since navy_flounder has the same ip offset with sienna_cichlid,
follow sienna_cichlid setting for the moment.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <Tao.Zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same as navi10.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Same as navi10.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the asic family and IP blocks for navy flounder.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently navy_flounder only supports backdoor loading type.
Will switch to psp load type when psp is ready.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Sienna_cichlid has four sdma instances, but other chips don't.
So we need expand to add multiple trap event irq id in sdma
v5.2.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1.Skip decode_ring test in VF, because VCN in SRIOV does not
support direct register read/write.
2.Skip powergating configuration in hw fini because
VCN3.0 SRIOV doesn't support powergating.
V2: delete unneccessary white lines and refine implementation.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1.In early_init and for sriov, hardcode
harvest_config=0, enc_num=1
2.sw_init/fini
alloc & free mm_table for sriov
doorbell setting for sriov
3.hw_init/fini
Under sriov, add start_sriov to config mmsch
Skip ring_test to avoid mmio in VF, but need to initialize wptr for vcn rings.
4.Implementation for vcn_v3_0_start_sriov
V2:Clean-up some uneccessary funciton declaration.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For VCN3.0 SRIOV, Guest driver needs to communicate with mmsch
to set the World Switch for MM appropriately. This patch add
the interface for mmsch_v3.0.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Reviewed-by: Dennis Li <Dennis.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For gfx10 boards, except for nv12, other boards take mmio write
rather than rlcg write
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For SIENNA_CICHLID SRIOV, jpeg and pgcp is not supported.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Leftover of previous performance level setting cleanups.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we are in RAS triggered situation and
BACO isn't support, emergency restart is needed,
and this code is only needed for some specific
cases(vega20 with given smu fw version).
After we add smu mode1 reset for sienna cichlid, we
need to share AMD_RESET_METHOD_MODE1 with psp mode1 reset,
so in amdgpu_device_gpu_recover, we need differentiate
which mode1 reset we are using, then decide if it's
a full reset and then decide if emergency restart is needed,
the logic will become much more complex.
After discussion with Hawking, move emergency restart logic
to an independent function.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Wenhui Sheng <Wenhui.Sheng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
"u64 *wptr" points to the the wptr value in write back buffer and
"*wptr = (*wptr) >> 2;" results in the value being overwritten each time
when ->get_wptr() is called.
umr uses /sys/kernel/debug/dri/0/amdgpu_ring_sdma0 to get rptr/wptr and
decode ring content and it is affected by this issue.
fix and simplify the logic similar as sdma_v4_0_ring_get_wptr().
v2: fix for sdma5.2 as well
Suggested-by: Le Ma <le.ma@amd.com>
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to easily add new debugfs file w/o changing the hardcoded list count.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a DRM_ERROR error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove signaled jobs from job list and ensure the
job was indeed preempted.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During preemption test for gfx10, it uses kiq to trigger
gfx preemption, which would result in race condition
with flushing TLB for kiq.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cleanup of phase1 suspend code to reduce unnecessary indentation.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This helps to maintain clear code layers and drop unnecessary
parameter.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This helps to maintain clear code layers and drop unnecessary
parameter.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove some unused ASIC check logic.
Remove some definition of amdgpu_device which only used by
the removed ASIC check logic.(V2)
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's impossible to debug shader hangs with soft recovery.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When I update the latest kernel, I see the following "____ptrval____" boot
messages.
[ 1.872600] radeon 0000:01:05.0: fence driver on ring 0 use gpu addr 0x0000000048000c00 and cpu addr 0x(____ptrval____)
[ 1.879095] radeon 0000:01:05.0: fence driver on ring 5 use gpu addr 0x0000000040056038 and cpu addr 0x(____ptrval____)
Both radeon_fence_driver_start_ring() and amdgpu_fence_driver_start_ring()
have the similar issue, there exists the following two methods to solve it:
(1) Use "%pK" instead of "%p" so that the CPU address can be printed when
the kptr_restrict sysctl is set to 1.
(2) Just completely drop the CPU address suggested by Christian, because
the CPU address was useful in the past, but isn't any more. We now have a
debugfs file to read the current fence values.
Since the CPU address is not much useful, just remove the debug info about
CPU address.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of hardcode
in mmhub v9.4.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of hardcode
in mmhub v2.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of hardcode
in mmhub v1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of hardcode
in gfxhub v2.1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of hardcode
in gfxhub v2.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of hardcode
in gfxhub v1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of hardcode
in VCN2/JEPG2. They are for the same ASIC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of hardcode
in UVD7/VCE4. They are for the same ASIC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of
hardcode in VCN1/JEPG1. They are for the same ASIC.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of hardcode
in GMC10.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates to use register distance member instead of hardcode
in GMC9.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to abstract register distances between two continuous
context domains and invalidation engines. In different ip headers, these
distances may be differences.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Tested-by: AnZhong Huang <anzhong.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the mutext lock/unlock outside of the if(),
as the mutex is always taken: either in the if()
branch or in the else branch.
Signed-off-by: Alex Jivin <alex.jivin@amd.com>
Suggested-By: Luben Tukov <luben.tuikov@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MMHUB powergating should be disabled on navi12 and enabled on sienna
cichlid.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use RREG32_KIQ to read gfx register when try to get gfx/sdma
clockgating state instead of RREG32, as it will result
to system hard hang when GPU is enter into GFXOFF state.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add support for loading ucode with ta_firmware_header_v2_0
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
