Pull m68k updates from Geert Uytterhoeven.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Make sys_atomic_cmpxchg_32 work on classic m68k
m68k/apollo: Rename "timer" to "apollo_timer"
zorro: Remove unused zorro_bus.devices
m68k: Remove never used asm/shm.h
m68k/sun3: Remove unselectable code in prom_init()
m68k: Use asm-generic version of <asm/sections.h>
m68k: Replace m68k-specific _[se]bss by generic __bss_{start,stop}
mtd/uclinux: Use generic __bss_stop instead of _ebss
m68knommu: Allow ColdFire CPUs to use unaligned accesses
m68k: Remove five unused headers
m68k: CPU32 does not support unaligned accesses
m68k: Introduce config option CPU_HAS_NO_UNALIGNED
m68k: delay, muldi3 - Use CONFIG_CPU_HAS_NO_MULDIV64
m68k: Move CPU_HAS_* config options
m68k: Remove duplicate FPU config option
m68knommu: Clean up printing of sections
m68k: Use asm-generic version of <asm/types.h>
m68k: Use Kbuild logic to import asm-generic headers
The ColdFire M54xx SoC family have a traditional PCI bus interface.
Add the core support code to access and use this bus on these parts.
This code provides all the config space access functions and IO access
functions. It also carries out the PCI bus initialization and hooks into
the kernel PCI subsystem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Quite a few of Freescale's older ColdFire development boards used an NS8390
based ethernet interface. Add a platform definition for the resources used
by these devices so we can use it on these boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The 532x has individually controllable clocks for it peripherals. Add clk
definitions for these and add default initialization of either enabled or
disabled.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The 520x has individually controllable clocks for its peripherals. Add clk
definitions for these and add default initialization of either enabled or
disabled for all of the clocks.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Add support for the Coldfire 5441x (54410/54415/54416/54417/54418). Currently
we only support noMMU mode. It requires the PIT patch posted previously as it
uses the PIT instead of the dma timer as a clock source so we can get all that
GENERIC_CLOCKEVENTS goodness. It also adds some simple clk definitions and
very simple minded power management. The gpio code is tweeked and some
additional devices are added to devices.c. The Makefile uses -mv4e as
apparently, the only difference a v4m (m5441x) and a v4e is the later has a
FPU, which I don't think should matter to us in the kernel.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
use MCF_IRQ_PIT1 instead of MCFINT_VECBASE + MCFINT_PIT1 so we can support
those parts that have the pit1 interrupt on other than the first interrupt
controller.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
If we're not connecting external GPIO extenders via i2c or spi or whatever, we
probably don't need GPIOLIB. If we provide an alternate implementation of
the GPIOLIB functions to use when only on-chip GPIO is needed, we can change
ARCH_REQUIRE_GPIOLIB to ARCH_WANTS_OPTIONAL_GPIOLIB so that GPIOLIB becomes
optional.
The downside is that in the GPIOLIB=n case, we lose all error checking done by
gpiolib, ie multiply allocating the gpio, free'ing gpio etc., so that the
only checking that can be done is if we reference a gpio on an external part.
Targets that need the extra error checking can still select GPIOLIB=y.
For the case where GPIOLIB=y, we can simplify the table of gpio chips to use a
single chip, eliminating the tables of chips in the 5xxx.c files. The
original motivation for the definition of multiple chips was to match the way
many of the Coldfire variants defined their gpio as a spare array in memory.
However, all this really gains us is some error checking when we request a
gpio, gpiolib can check that it doesn't fall in one of the holes. If thats
important, I think we can still come up with a better way of accomplishing
that.
Also in this patch is some general cleanup and reorganizing of the gpio header
files (I'm sure I must have had a reason why I sometimes used a prefix of
mcf_gpio and other times mcfgpio but for the life of me I can't think of it
now).
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
BSS_SECTION() provides the __bss_{start,stop} symbols, so there's no need
to wrap our own _[se]bss around it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer<gerg@uclinux.org>
Commit f4d40de39a ("net fec: do not depend
on grouped clocks") breaks compilation of the FEC driver for non iMX
platforms in linux-3.5-rc1. For example when compiling for ColdFire I get:
LD vmlinux
drivers/built-in.o: In function `fec_probe':
fec.c:(.devinit.text+0x1e0): undefined reference to `devm_clk_get'
Define a simple devm_clk_get() function for the m68knommu architecture.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Compiling for 68360 based targets fails with:
arch/m68k/platform/68360/config.c: In function ‘hw_tick’:
arch/m68k/platform/68360/config.c:55:2: error: implicit declaration of function ‘arch_timer_interrupt’
arch/m68k/platform/68360/config.c: At top level:
arch/m68k/platform/68360/config.c:64:6: error: conflicting types for ‘hw_timer_init’
arch/m68k/include/asm/machdep.h:36:13: note: previous declaration of ‘hw_timer_init’ was here
Changes made to hw_timer_init() didn't get updated in the 68328 timer code.
So process and call the "handler" arg that is now passed into that
hw_timer_init() function.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Compiling for 68328 based targets fails with:
arch/m68k/platform/68328/timers.c: In function ‘hw_tick’:
arch/m68k/platform/68328/timers.c:65:2: error: implicit declaration of function ‘arch_timer_interrupt’
arch/m68k/platform/68328/timers.c: At top level:
arch/m68k/platform/68328/timers.c:102:6: error: conflicting types for ‘hw_timer_init’
arch/m68k/include/asm/machdep.h:36:13: note: previous declaration of ‘hw_timer_init’ was here
Changes made to hw_timer_init() didn't get updated in the 68328 timer code.
So process and call the "handler" arg that is now passed into that
hw_timer_init() function.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Pull first series of signal handling cleanups from Al Viro:
"This is just the first part of the queue (about a half of it);
assorted fixes all over the place in signal handling.
This one ends with all sigsuspend() implementations switched to
generic one (->saved_sigmask-based).
With this, a bunch of assorted old buglets are fixed and most of the
missing bits of NOTIFY_RESUME hookup are in place. Two more fixes sit
in arm and um trees respectively, and there's a couple of broken ones
that need obvious fixes - parisc and avr32 check TIF_NOTIFY_RESUME
only on one of two codepaths; fixes for that will happen in the next
series"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (55 commits)
unicore32: if there's no handler we need to restore sigmask, syscall or no syscall
xtensa: add handling of TIF_NOTIFY_RESUME
microblaze: drop 'oldset' argument of do_notify_resume()
microblaze: handle TIF_NOTIFY_RESUME
score: add handling of NOTIFY_RESUME to do_notify_resume()
m68k: add TIF_NOTIFY_RESUME and handle it.
sparc: kill ancient comment in sparc_sigaction()
h8300: missing checks of __get_user()/__put_user() return values
frv: missing checks of __get_user()/__put_user() return values
cris: missing checks of __get_user()/__put_user() return values
powerpc: missing checks of __get_user()/__put_user() return values
sh: missing checks of __get_user()/__put_user() return values
sparc: missing checks of __get_user()/__put_user() return values
avr32: struct old_sigaction is never used
m32r: struct old_sigaction is never used
xtensa: xtensa_sigaction doesn't exist
alpha: tidy signal delivery up
score: don't open-code force_sigsegv()
cris: don't open-code force_sigsegv()
blackfin: don't open-code force_sigsegv()
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
TIF_NOTIFY_RESUME added (as bit 5). That way nommu glue needs no changes at
all; mmu one needs just to replace jmi do_signal_return to jne do_signal_return
There we have flags shifted up, until bit 6 (SIGPENDING) is in MSBit; instead
of checking that MSBit is set (jmi) we check that MSBit or something below it
is set (jne); bits 0..4 are never set, so that's precisely "bit 6 or bit 5 is
set".
Usual handling of NOTIFY_RESUME/SIGPENDING is done in do_notify_resume(); glue
calls it instead of do_signal().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
All these separate directories for each ColdFire CPU SoC varient seems like
overkill. The majority of them only contain a single small config file. Move
these into the common ColdFire code directory.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The GPIO data struct setup is now the only remaining code in the platform
gpio.c file. So move it to the platform config.c code and remove the gpio.c
file.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
The code that adds each ColdFire platforms GPIO signals is duplicated in
each platforms specific code. Remove it from each platforms code and put
a single version in the existing ColdFire gpio subsystem init code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
We also need to rename some of the GPIO registers to be consistent with
all other ColdFire parts (we can't use the new GPIO macros otherwise).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
Modify the GPIO setup table to use the mcfgpio.h macros for table init.
Simplifies code and reduces line count significantly.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Steven King <sfking@fdwdc.com>
That old mail address doesnt exist any more.
This changes all occurences to a current address.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Acked-by: Sebastian Heß <shess@hessware.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
