The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to align the RX buffer size to at least 16 byte so that IP
doesn't mis-behave. This is required by HW.
Changes from v2:
- Align UP and not DOWN (David)
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching between buffer sizes we need to clear the previous value.
Fixes: d6ddfacd95 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the last received buffer contains the FCS field. Check for end of
packet before trying to strip the FCS field.
Fixes: 88ebe2cf7f ("net: stmmac: Rework stmmac_rx()")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum MTU value is determined by the maximum size of TX FIFO so
that a full packet can fit in the FIFO. Add a check for this in the MTU
change callback.
Also check if provided and rounded MTU does not passes the maximum limit
of 16K.
Changes from v2:
- Align MTU before checking if its valid
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split Header feature needs to know the size of RX buffer but current
code is determining it too late. Fix this by moving the RX buffer
computation to earlier stage.
Changes from v2:
- Do not try to align already aligned buffer size
Fixes: 67afd6d1cf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the MC and UC filter tests we setup a multicast address
that its expected to be blocked. If the number of available multicast
registers is zero, driver will always pass the multicast packets which
will fail the test.
Check if available multicast addresses is enough before running the
tests.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
net/nfc/nci/uart.c, 349:
nci_skb_alloc in nci_uart_default_recv_buf
net/nfc/nci/uart.c, 255:
(FUNC_PTR)nci_uart_default_recv_buf in nci_uart_tty_receive
net/nfc/nci/uart.c, 254:
spin_lock in nci_uart_tty_receive
nci_skb_alloc(GFP_KERNEL) can sleep at runtime.
(FUNC_PTR) means a function pointer is called.
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC for
nci_skb_alloc().
This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've been chasing a weird and obscure crash that was userspace stack
corruption, and finally narrowed it down to a bit flip that made a
stack address invalid. io_wq_submit_work() unconditionally flips
the req->rw.ki_flags IOCB_NOWAIT bit, but since it's a generic work
handler, this isn't valid. Normal read/write operations own that
part of the request, on other types it could be something else.
Move the IOCB_NOWAIT clear to the read/write handlers where it belongs.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The following build warning is seen if CONFIG_PM is disabled.
drivers/usb/host/xhci-pci.c:498:13: warning:
unused function 'xhci_pci_shutdown'
Fixes: f2c710f7dc ("usb: xhci: only set D3hot for pci device")
Cc: Henry Lin <henryl@nvidia.com>
Cc: stable@vger.kernel.org # all stable releases with f2c710f7dc
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20191218011911.6907-1-linux@roeck-us.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent addition exposed a helper that is only used for CONFIG_OF. Move
it into the CONFIG_OF zone in this file to make the compiler stop
warning about an unused function.
Fixes: 66d9506440 ("clk: walk orphan list on clock provider registration")
Signed-off-by: Olof Johansson <olof@lixom.net>
Link: https://lkml.kernel.org/r/20191217082501.424892072D@mail.kernel.org
[sboyd@kernel.org: "Simply" move the function instead]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no reliable way to submit and wait in a single syscall, as
io_submit_sqes() may under-consume sqes (in case of an early error).
Then it will wait for not-yet-submitted requests, deadlocking the user
in most cases.
Don't wait/poll if can't submit all sqes
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A slightly high amount at this time, but all good and small fixes.
- A PCM core fix that initializes the buffer properly for avoiding
information leaks; it is a long-standing minor problem, but good
to fix better now
- A few ASoC core fixes for the init / cleanup ordering issues
that surfaced after the recent refactoring
- Lots of SOF and topology-related fixes went in, as usual as such
hot topics
- Several ASoC codec and platform-specific small fixes: wm89xx,
realtek, and max98090, AMD, Intel-SST
- A fix for the previous incomplete regression of HD-audio, now
hitting Nvidia HDMI
- A few HD-audio CA0132 codec fixes
-----BEGIN PGP SIGNATURE-----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=eyq5
-----END PGP SIGNATURE-----
Merge tag 'sound-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A slightly high amount at this time, but all good and small fixes:
- A PCM core fix that initializes the buffer properly for avoiding
information leaks; it is a long-standing minor problem, but good to
fix better now
- A few ASoC core fixes for the init / cleanup ordering issues that
surfaced after the recent refactoring
- Lots of SOF and topology-related fixes went in, as usual as such
hot topics
- Several ASoC codec and platform-specific small fixes: wm89xx,
realtek, and max98090, AMD, Intel-SST
- A fix for the previous incomplete regression of HD-audio, now
hitting Nvidia HDMI
- A few HD-audio CA0132 codec fixes"
* tag 'sound-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (27 commits)
ALSA: hda - Downgrade error message for single-cmd fallback
ASoC: wm8962: fix lambda value
ALSA: hda: Fix regression by strip mask fix
ALSA: hda/ca0132 - Fix work handling in delayed HP detection
ALSA: hda/ca0132 - Avoid endless loop
ALSA: hda/ca0132 - Keep power on during processing DSP response
ALSA: pcm: Avoid possible info leaks from PCM stream buffers
ASoC: Intel: common: work-around incorrect ACPI HID for CML boards
ASoC: SOF: Intel: split cht and byt debug window sizes
ASoC: SOF: loader: fix snd_sof_fw_parse_ext_data
ASoC: SOF: loader: snd_sof_fw_parse_ext_data log warning on unknown header
ASoC: simple-card: Don't create separate link when platform is present
ASoC: topology: Check return value for soc_tplg_pcm_create()
ASoC: topology: Check return value for snd_soc_add_dai_link()
ASoC: core: only flush inited work during free
ASoC: Intel: bytcr_rt5640: Update quirk for Teclast X89
ASoC: core: Init pcm runtime work early to avoid warnings
ASoC: Intel: sst: Add missing include <linux/io.h>
ASoC: max98090: fix possible race conditions
ASoC: max98090: exit workaround earlier if PLL is locked
...
The host reports support for the synthetic feature X86_FEATURE_SSBD
when any of the three following hardware features are set:
CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31]
CPUID.80000008H:EBX.AMD_SSBD[bit 24]
CPUID.80000008H:EBX.VIRT_SSBD[bit 25]
Either of the first two hardware features implies the existence of the
IA32_SPEC_CTRL MSR, but CPUID.80000008H:EBX.VIRT_SSBD[bit 25] does
not. Therefore, CPUID.80000008H:EBX.AMD_SSBD[bit 24] should only be
set in the guest if CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31] or
CPUID.80000008H:EBX.AMD_SSBD[bit 24] is set on the host.
Fixes: 4c6903a0f9 ("KVM: x86: fix reporting of AMD speculation bug CPUID leaf")
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Jacob Xu <jacobhxu@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Reported-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The host reports support for the synthetic feature X86_FEATURE_SSBD
when any of the three following hardware features are set:
CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31]
CPUID.80000008H:EBX.AMD_SSBD[bit 24]
CPUID.80000008H:EBX.VIRT_SSBD[bit 25]
Either of the first two hardware features implies the existence of the
IA32_SPEC_CTRL MSR, but CPUID.80000008H:EBX.VIRT_SSBD[bit 25] does
not. Therefore, CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31] should only be
set in the guest if CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31] or
CPUID.80000008H:EBX.AMD_SSBD[bit 24] is set on the host.
Fixes: 0c54914d0c ("KVM: x86: use Intel speculation bugs and features as derived in generic x86 code")
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Jacob Xu <jacobhxu@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Reported-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit ece6e6f021 ("iommu/dma-iommu: Split iommu_dma_map_msi_msg()
in two parts"), iommu_dma_prepare_msi() should no longer have to worry
about preempting itself, nor being called in atomic context at all. Thus
we can downgrade the IRQ-safe locking to a simple mutex to avoid angering
the new might_sleep() check in iommu_map().
Reported-by: Qian Cai <cai@lca.pw>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In smmu_pmu_probe(), there is put_cpu() in the error path,
which is wrong because we use raw_smp_processor_id() to
get the cpu ID, not get_cpu(), remove it.
While we are at it, kill 'out_cpuhp_err' altogether and
just return err if we fail to add the hotplug instance.
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The PSI (Page Selective Invalidation) bit in the capability register
is only valid for second-level translation. Intel IOMMU supporting
scalable mode must support page/address selective IOTLB invalidation
for first-level translation. Remove the PSI capability check in SVA
cache invalidation code.
Fixes: 8744daf4b0 ("iommu/vt-d: Remove global page flush support")
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The driver checks that the number of retries made by the device is
coherent with the rate policy. However, this check make sense only if
the device has returned RETRY_EXCEEDED.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-11-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code has a special case to handle association with WEP. Before
to rework the tx data handling, let's try to detect any possible misuse
of this code.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-9-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When not using HT mode, minstrel always includes 1Mbps as fallback rate.
But, when using HT mode, this fallback is not included. Yet, it seems
that it could save some frames. So, this patch add it unconditionally.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-8-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A tx_retry_policy (the equivalent of a list of ieee80211_tx_rate in
hardware API) is not able to include a rate multiple time. So currently,
the driver merges the identical rates from the policy provided by
minstrel (and it try to do the best choice it can in the associated
flags) before to sent it to firmware.
Until now, when rates are merged, field "count" is set to
max(count1, count2). But, it means that the sum of retries for all rates
could be far less than initial number of retries. So, this patch changes
the value of field "count" to count1 + count2. Thus, sum of all retries
for all rates stay the same.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-7-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sum of all retries for a Tx frame cannot be superior to 32.
There are 4 rates at most. So this patch limits number of retries per
rate to 8.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-6-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some weird behaviors were observed when connection is really good and
packets are small. It appears that sometime, number of packets in queues
can exceed 255 and generate an overflow in field usage_count.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-4-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some rare cases, driver may not have any available tx_retry_policies.
In this case, the driver asks to mac80211 to stop sending data. However,
it seems that a race is possible and a few frames can be sent to the
driver. In this case, driver can't wait for free tx_retry_policies since
wfx_tx() must be atomic. So, this patch fix this case by sending these
frames with the special policy number 15.
The firmware normally use policy 15 to send internal frames (PS-poll,
beacons, etc...). So, it is not a so bad fallback.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-3-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device and driver maintain a cache of rate policies (aka.
tx_retry_policy in hardware API).
When hif_reset() is sent to hardware, device resets its cache of rate
policies. In order to keep driver in sync, it is necessary to do the
same on driver.
Note, when driver tries to use a rate policy that has not been defined
on device, data is sent at 1Mbps. So, this patch should fix abnormal
throughput observed sometime after a reset of the interface.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20191217161318.31402-2-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update user's and administrator's guide to mention USB4, how it relates
to Thunderbolt and and how it is supported in Linux.
While there add the missing SPDX identifier to the document.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-10-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 added a capability to tunnel USB 3.x protocol over the USB4
fabric. USB4 device routers may include integrated SuperSpeed HUB or a
function or both. USB tunneling follows PCIe so that the tunnel is
created between the parent and the child router from USB3 downstream
adapter port to USB3 upstream adapter port over a single USB4 link.
This adds support for USB 3.x tunneling and also capability to discover
existing USB 3.x tunnels (for example created by connection manager in
boot firmware).
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-9-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Time Management Unit (TMU) is included in each USB4 router. It is used
to synchronize time across the USB4 fabric. By default when USB4 router
is plugged to the domain, its TMU is turned off. This differs from
Thunderbolt (1, 2 and 3) devices whose TMU is by default configured to
bi-directional HiFi mode. Since time synchronization is needed for
proper Display Port tunneling this means we need to configure the TMU on
USB4 compliant devices.
The USB4 spec allows some flexibility on how the TMU can be configured.
This makes it possible to enable link power management states (CLx) in
certain topologies, where for example DP tunneling is not used. TMU can
also be re-configured dynamicaly depending on types of tunnels created
over the USB4 fabric.
In this patch we simply configure the TMU to be in bi-directional HiFi
mode. This way we can tunnel any kind of traffic without need to perform
complex steps to re-configure the domain dynamically. We can add more
fine-grained TMU configuration later on when we start enabling CLx
states.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-8-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to find switch capabilities in order to implement TMU support so
make it available to other files as well.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-7-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the driver now supports USB4 which is the standard going forward,
update the Kconfig entry to mention this and rename the entry from
CONFIG_THUNDERBOLT to CONFIG_USB4 instead to help people to find the
correct option if they want to enable USB4.
Also do the same for Thunderbolt network driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20191217123345.31850-6-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 is the public specification based on Thunderbolt 3 protocol. There
are some differences in register layouts and flows. In addition to PCIe
and DP tunneling, USB4 supports tunneling of USB 3.x. USB4 is also
backward compatible with Thunderbolt 3 (and older generations but the
spec only talks about 3rd generation). USB4 compliant devices can be
identified by checking USB4 version field in router configuration space.
This patch adds initial support for USB4 compliant hosts and devices
which enables following features provided by the existing functionality
in the driver:
- PCIe tunneling
- Display Port tunneling
- Host and device NVM firmware upgrade
- P2P networking
This brings the USB4 support to the same level that we already have for
Thunderbolt 1, 2 and 3 devices.
Note the spec talks about host and device "routers" but in the driver we
still use term "switch" in most places. Both can be used interchangeably.
Co-developed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-5-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 1.0 section 6.4.2.7 specifies a new field (PG) in notification
packet that is sent as response of hot plug/unplug events. This field
tells whether the acknowledgment is for plug or unplug event. This needs
to be set accordingly in order the router to send further hot plug
notifications.
To make it simpler we fill the field unconditionally. Legacy devices do
not look at this field so there should be no problems with them.
While there rename tb_cfg_error() to tb_cfg_ack_plug() and update the
log message accordingly. The function is only used to ack plug/unplug
events.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-4-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are going to re-use tb_drom_read() for USB4 DROM reading as well.
USB4 has separate router operations for this which does not need the
drom_offset. Therefore we move call to tb_eeprom_get_drom_offset() into
tb_eeprom_read_n() where it is needed.
While there change return -ENOSYS to -ENODEV because the former is only
supposed to be used with system calls (invalid syscall nr).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-3-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will be needing this when adding initial USB4 support so make it
available to other files in the driver as well. We also rename it to
tb_switch_find_port() to follow conventions used in switch.c.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-2-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), scripts/checkpatch.pl warns the use of ---help---.
Kconfig still supports ---help---, but new code should avoid using it.
Let's stop advertising it in documentation.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Command queuing has been reported broken on some systems based on Intel
GLK. A separate patch disables command queuing in some cases.
This patch adds a quirk for broken command queuing, which enables users
with problems to disable command queuing using sdhci module parameters for
quirks.
Fixes: 8ee82bda23 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Command queuing has been reported broken on some Lenovo systems based on
Intel GLK. This is likely a BIOS issue, so disable command queuing for
Intel GLK if the BIOS vendor string is "LENOVO".
Fixes: 8ee82bda23 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Two previous patches introduced below quirks for P2020 platforms.
- SDHCI_QUIRK_RESET_AFTER_REQUEST
- SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
The patches made a mistake to add them in quirks2 of sdhci_host
structure, while they were defined for quirks.
host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
This patch is to fix them.
host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
Fixes: 05cb6b2a66 ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support")
Fixes: a46e427125 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Get_pid_task() needs to be paired with a put_pid or we leak a pid
reference every time a banned client tries to create a context.
v2:
* task_pid_nr helper exists! (Chris)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b083a0870c ("drm/i915: Add per client max context ban limit")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217170933.8108-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit ba16a48af7)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since commit e5dadff4b0 ("drm/i915: Protect request retirement with
timeline->mutex"), the request retirement can happen outside of the
struct_mutex serialised only by the timeline->mutex. We drop the
timeline->mutex on submitting the request (i915_request_add) so after
that point, it is liable to be freed. Make sure our local reference is
kept alive until we have finished attaching it to the signalers. (Note
that this erodes the argument that i915_request_add should consume the
reference, but that is a slightly larger patch!)
Fixes: e5dadff4b0 ("drm/i915: Protect request retirement with timeline->mutex")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217134729.3297818-1-chris@chris-wilson.co.uk
(cherry picked from commit e14177f197)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Dev_hold has to be called always in rx_queue_add_kobject.
Otherwise usage count drops below 0 in case of failure in
kobject_init_and_add.
Fixes: b8eb718348 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject")
Reported-by: syzbot <syzbot+30209ea299c09d8785c9@syzkaller.appspotmail.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As flower rules are added, they are given a stats ID based on the number
of rules that can be supported in firmware. Only after the initial
allocation of all available IDs does the driver begin to reuse those that
have been released.
The initial allocation of IDs was modified to account for multiple memory
units on the offloaded device. However, this introduced a bug whereby the
counter that controls the IDs could be decremented before the ID was
assigned (where it is further decremented). This means that the stats ID
could be assigned as -1/0xfffffff which is out of range.
Fix this by only decrementing the main counter after the current ID has
been assigned.
Fixes: 467322e262 ("nfp: flower: support multiple memory units for filter offloads")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dsa_link_touch() is not exported, or defined outside of the
file it is in so make it static to avoid the following warning:
net/dsa/dsa2.c:127:17: warning: symbol 'dsa_link_touch' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/atheros/ag71xx.c: In function 'ag71xx_probe':
drivers/net/ethernet/atheros/ag71xx.c:1776:30: warning: passing argument 2 of
'of_get_phy_mode' makes pointer from integer without a cast [-Wint-conversion]
In file included from drivers/net/ethernet/atheros/ag71xx.c:33:
./include/linux/of_net.h:15:69: note: expected 'phy_interface_t *'
{aka 'enum <anonymous> *'} but argument is of type 'int'
Fixes: 0c65b2b90d ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix missing '*' kernel-doc notation that causes this warning:
../include/linux/netdevice.h:1779: warning: bad line: spinlock
Fixes: ab92d68fc2 ("net: core: add generic lockdep keys")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
