There is no harm, when users can read the info and we ask often enough
during debugging for this kind of information.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
File permissions for
/sys/devices/system/clocksource/clocksource0/available_clocksource
are 600 which allows write access. But this is in fact a read only
file. So change permissions to 400.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove the leap second handling from second_overflow(), which doesn't have to
check for it every second anymore. With CONFIG_NO_HZ this also makes sure the
leap second is handled close to the full second. Additionally this makes it
possible to abort a leap second properly by resetting the STA_INS/STA_DEL
status bits.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
current_tick_length used to do a little more, but now it just returns
tick_length, which we can also access directly at the few places, where it's
needed.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As TICK_LENGTH_SHIFT is used for more than just the tick length, the name
isn't quite approriate anymore, so this renames it to NTP_SCALE_SHIFT.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for setting the TAI value (International Atomic Time). The
value is reported back to userspace via timex (as we don't have a
ntp_gettime() syscall).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
time_offset is already a 64bit value but its resolution barely used, so this
makes better use of it by replacing SHIFT_UPDATE with TICK_LENGTH_SHIFT.
Side note: the SHIFT_HZ in SHIFT_UPDATE was incorrect for CONFIG_NO_HZ and the
primary reason for changing time_offset to 64bit to avoid the overflow.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes time_freq to a 64bit value and makes it static (the only outside
user had no real need to modify it). Intermediate values were already 64bit,
so the change isn't that big, but it saves a little in shifts by replacing
SHIFT_NSEC with TICK_LENGTH_SHIFT. PPM_SCALE is then used to convert between
user space and kernel space representation.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a few more things from the ntp nanokernel related to user space.
It's now possible to select the resolution used of some values via STA_NANO
and the kernel reports in which mode it works (pll/fll).
If some values for adjtimex() are outside the acceptable range, they are now
simply normalized instead of letting the syscall fail. I removed
MOD_CLKA/MOD_CLKB as the mapping didn't really makes any sense, the kernel
doesn't support setting the clock.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly a style cleanup of ntp.c and extracts part of do_adjtimex as
ntp_update_offset(). Otherwise the functionality is still the same as before.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86 is the only arch right now, which provides an optimized for
div_long_long_rem and it has the downside that one has to be very careful that
the divide doesn't overflow.
The API is a little akward, as the arguments for the unsigned divide are
signed. The signed version also doesn't handle a negative divisor and
produces worse code on 64bit archs.
There is little incentive to keep this API alive, so this converts the few
users to the new API.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This converts a few users of do_div to div_[su]64 and this demonstrates nicely
how it can reduce some expressions to one-liners.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Miller reported:
|--------------->
the following commit:
| commit 27ec440779
| Author: Ingo Molnar <mingo@elte.hu>
| Date: Thu Feb 28 21:00:21 2008 +0100
|
| sched: make cpu_clock() globally synchronous
|
| Alexey Zaytsev reported (and bisected) that the introduction of
| cpu_clock() in printk made the timestamps jump back and forth.
|
| Make cpu_clock() more reliable while still keeping it fast when it's
| called frequently.
|
| Signed-off-by: Ingo Molnar <mingo@elte.hu>
causes watchdog triggers when a cpu exits NOHZ state when it has been
there for >= the soft lockup threshold, for example here are some
messages from a 128 cpu Niagara2 box:
[ 168.106406] BUG: soft lockup - CPU#11 stuck for 128s! [dd:3239]
[ 168.989592] BUG: soft lockup - CPU#21 stuck for 86s! [swapper:0]
[ 168.999587] BUG: soft lockup - CPU#29 stuck for 91s! [make:4511]
[ 168.999615] BUG: soft lockup - CPU#2 stuck for 85s! [swapper:0]
[ 169.020514] BUG: soft lockup - CPU#37 stuck for 91s! [swapper:0]
[ 169.020514] BUG: soft lockup - CPU#45 stuck for 91s! [sh:4515]
[ 169.020515] BUG: soft lockup - CPU#69 stuck for 92s! [swapper:0]
[ 169.020515] BUG: soft lockup - CPU#77 stuck for 92s! [swapper:0]
[ 169.020515] BUG: soft lockup - CPU#61 stuck for 92s! [swapper:0]
[ 169.112554] BUG: soft lockup - CPU#85 stuck for 92s! [swapper:0]
[ 169.112554] BUG: soft lockup - CPU#101 stuck for 92s! [swapper:0]
[ 169.112554] BUG: soft lockup - CPU#109 stuck for 92s! [swapper:0]
[ 169.112554] BUG: soft lockup - CPU#117 stuck for 92s! [swapper:0]
[ 169.171483] BUG: soft lockup - CPU#40 stuck for 80s! [dd:3239]
[ 169.331483] BUG: soft lockup - CPU#13 stuck for 86s! [swapper:0]
[ 169.351500] BUG: soft lockup - CPU#43 stuck for 101s! [dd:3239]
[ 169.531482] BUG: soft lockup - CPU#9 stuck for 129s! [mkdir:4565]
[ 169.595754] BUG: soft lockup - CPU#20 stuck for 93s! [swapper:0]
[ 169.626787] BUG: soft lockup - CPU#52 stuck for 93s! [swapper:0]
[ 169.626787] BUG: soft lockup - CPU#84 stuck for 92s! [swapper:0]
[ 169.636812] BUG: soft lockup - CPU#116 stuck for 94s! [swapper:0]
It's simple enough to trigger this by doing a 10 minute sleep after a
fresh bootup then starting a parallel kernel build.
I suspect this might be reintroducing a problem we've had and fixed
before, see the thread:
http://marc.info/?l=linux-kernel&m=119546414004065&w=2
<---------------|
touch the softlockup watchdog when exiting NOHZ state - we are
obviously not locked up.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
hrtimer: optimize the softirq time optimization
hrtimer: reduce calls to hrtimer_get_softirq_time()
clockevents: fix typo in tick-broadcast.c
jiffies: add time_is_after_jiffies and others which compare with jiffies
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel: (62 commits)
sched: build fix
sched: better rt-group documentation
sched: features fix
sched: /debug/sched_features
sched: add SCHED_FEAT_DEADLINE
sched: debug: show a weight tree
sched: fair: weight calculations
sched: fair-group: de-couple load-balancing from the rb-trees
sched: fair-group scheduling vs latency
sched: rt-group: optimize dequeue_rt_stack
sched: debug: add some debug code to handle the full hierarchy
sched: fair-group: SMP-nice for group scheduling
sched, cpuset: customize sched domains, core
sched, cpuset: customize sched domains, docs
sched: prepatory code movement
sched: rt: multi level group constraints
sched: task_group hierarchy
sched: fix the task_group hierarchy for UID grouping
sched: allow the group scheduler to have multiple levels
sched: mix tasks and groups
...
braodcast -> broadcast
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Various SMP balancing algorithms require that the bandwidth period
run in sync.
Possible improvements are moving the rt_bandwidth thing into root_domain
and keeping a span per rt_bandwidth which marks throttled cpus.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We already catch most of the TSC problems by sanity checks, but there
is a subtle bug which has been in the code forever. This can cause
time jumps in the range of hours.
This was reported in:
http://lkml.org/lkml/2007/8/23/96
and
http://lkml.org/lkml/2008/3/31/23
I was able to reproduce the problem with a gettimeofday loop test on a
dual core and a quad core machine which both have sychronized
TSCs. The TSCs seems not to be perfectly in sync though, but the
kernel is not able to detect the slight delta in the sync check. Still
there exists an extremly small window where this delta can be observed
with a real big time jump. So far I was only able to reproduce this
with the vsyscall gettimeofday implementation, but in theory this
might be observable with the syscall based version as well.
CPU 0 updates the clock source variables under xtime/vyscall lock and
CPU1, where the TSC is slighty behind CPU0, is reading the time right
after the seqlock was unlocked.
The clocksource reference data was updated with the TSC from CPU0 and
the value which is read from TSC on CPU1 is less than the reference
data. This results in a huge delta value due to the unsigned
subtraction of the TSC value and the reference value. This algorithm
can not be changed due to the support of wrapping clock sources like
pm timer.
The huge delta is converted to nanoseconds and added to xtime, which
is then observable by the caller. The next gettimeofday call on CPU1
will show the correct time again as now the TSC has advanced above the
reference value.
To prevent this TSC specific wreckage we need to compare the TSC value
against the reference value and return the latter when it is larger
than the actual TSC value.
I pondered to mark the TSC unstable when the readout is smaller than
the reference value, but this would render an otherwise good and fast
clocksource unusable without a real good reason.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
clocksource: make clocksource watchdog cycle through online CPUs
Documentation: move timer related documentation to a single place
clockevents: optimise tick_nohz_stop_sched_tick() a bit
locking: remove unused double_spin_lock()
hrtimers: simplify lockdep handling
timers: simplify lockdep handling
posix-timers: fix shadowed variables
timer_list: add annotations to workqueue.c
hrtimer: use nanosleep specific restart_block fields
hrtimer: add nanosleep specific restart_block member
In order to not trip the clocksource watchdog, kgdb must touch the
clocksource watchdog on the return to normal system run state.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This way it checks if the clocks are synchronized between CPUs too.
This might be able to detect slowly drifting TSCs which only
go wrong over longer time.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Call
ts = &per_cpu(tick_cpu_sched, cpu);
and
cpu = smp_processor_id();
once instead of twice.
No functional change done, as changed code runs with local irq off.
Reduces source lines and text size (20bytes on x86_64).
[ akpm@linux-foundation.org: Build fix ]
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
> Generic code is not supposed to include irq.h. Replace this include
> by linux/hardirq.h instead and add/replace an include of linux/irq.h
> in asm header files where necessary.
> This change should only matter for architectures that make use of
> GENERIC_CLOCKEVENTS.
> Architectures in question are mips, x86, arm, sh, powerpc, uml and sparc64.
>
> I did some cross compile tests for mips, x86_64, arm, powerpc and sparc64.
> This patch fixes also build breakages caused by the include replacement in
> tick-common.h.
I generally dislike adding optional linux/* includes in asm/* includes -
I'm nervous about this causing include loops.
However, there's a separate point to be discussed here.
That is, what interfaces are expected of every architecture in the kernel.
If generic code wants to be able to set the affinity of interrupts, then
that needs to become part of the interfaces listed in linux/interrupt.h
rather than linux/irq.h.
So what I suggest is this approach instead (against Linus' tree of a
couple of days ago) - we move irq_set_affinity() and irq_can_set_affinity()
to linux/interrupt.h, change the linux/irq.h includes to linux/interrupt.h
and include asm/irq_regs.h where needed (asm/irq_regs.h is supposed to be
rarely used include since not much touches the stacked parent context
registers.)
Build tested on ARM PXA family kernels and ARM's Realview platform
kernels which both use genirq.
[ tglx@linutronix.de: add GENERIC_HARDIRQ dependencies ]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Revert
commit 1077f5a917
Author: Parag Warudkar <parag.warudkar@gmail.com>
Date: Wed Jan 30 13:30:01 2008 +0100
clocksource.c: use init_timer_deferrable for clocksource_watchdog
clocksource_watchdog can use a deferrable timer - reduces wakeups from
idle per second.
The watchdog timer needs to run with the specified interval. Otherwise
it will miss the possible wrap of the watchdog clocksource.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
The printk() can deadlock because it can wake up klogd(), and
task enqueueing will try to read the time in order to set a hrtimer.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Debugged-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 1ada5cba6a ("clocksource:
make clocksource watchdog cycle through online CPUs") due to the
regression reported by Gabriel C at
http://lkml.org/lkml/2008/2/24/281
(short vesion: it makes TSC be marked as always unstable on his
machine).
Cc: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Robert Hancock <hancockr@shaw.ca>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The first version of the ntp_interval/tick_length inconsistent usage patch was
recently merged as bbe4d18ac2http://git.kernel.org/gitweb.cgi?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=bbe4d18ac2e058c56adb0cd71f49d9ed3216a405
While the fix did greatly improve the situation, it was correctly pointed out
by Roman that it does have a small bug: If the users change clocksources after
the system has been running and NTP has made corrections, the correctoins made
against the old clocksource will be applied against the new clocksource,
causing error.
The second attempt, which corrects the issue in the NTP_INTERVAL_LENGTH
definition has also made it up-stream as commit
e13a2e61ddhttp://git.kernel.org/gitweb.cgi?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=e13a2e61dd5152f5499d2003470acf9c838eab84
Roman has correctly pointed out that CLOCK_TICK_ADJUST is calculated
based on the PIT's frequency, and isn't really relevant to non-PIT
driven clocksources (that is, clocksources other then jiffies and pit).
This patch reverts both of those changes, and simply removes
CLOCK_TICK_ADJUST.
This does remove the granularity error correction for users of PIT and Jiffies
clocksource users, but the granularity error but for the majority of users, it
should be within the 500ppm range NTP can accommodate for.
For systems that have granularity errors greater then 500ppm, the
"ntp_tick_adj=" boot option can be used to compensate.
[johnstul@us.ibm.com: provided changelog]
[mattilinnanvuori@yahoo.com: maek ntp_tick_adj static]
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Acked-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Matti Linnanvuori <mattilinnanvuori@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Silences WARN_ONs in rcu_enter_nohz() and rcu_exit_nohz(), which appeared
before caused by (repeated) calls to:
$ echo 0 > /sys/devices/system/cpu/cpu1/online
$ echo 1 > /sys/devices/system/cpu/cpu1/online
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Cc: johnstul@us.ibm.com
Cc: Rafael Wysocki <rjw@sisk.pl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The kernel NTP code shouldn't hand 64-bit *signed* values to do_div(). Make it
instead hand 64-bit unsigned values. This gets rid of a couple of warnings.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The PREEMPT-RCU can get stuck if a CPU goes idle and NO_HZ is set. The
idle CPU will not progress the RCU through its grace period and a
synchronize_rcu my get stuck. Without this patch I have a box that will
not boot when PREEMPT_RCU and NO_HZ are set. That same box boots fine
with this patch.
This patch comes from the -rt kernel where it has been tested for
several months.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Relative expiry time can get negative, so it should be signed.
Signed-off-by: Pavel Machek <Pavel@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
clocksource initialization and error accumulation. This corrects a 280ppm
drift seen on some systems using acpi_pm, and affects other clocksources as
well (likely to a lesser degree).
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix typo in comments.
BTW: I have to fix coding style in arch/ia64/kernel/time.c also, otherwise
checkpatch.pl will be complaining.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Function timekeeping_is_continuous() no longer checks flag
CLOCK_IS_CONTINUOUS, and it checks CLOCK_SOURCE_VALID_FOR_HRES now. So rename
the function accordingly.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flag CLOCK_SOURCE_WATCHDOG is cleared twice. Note clocksource_change_rating()
won't do anyting with the cs flag.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found that there is a buffer overflow problem in the following code.
Version: 2.6.24-rc2,
File: kernel/time/clocksource.c:417-432
--------------------------------------------------------------------
static ssize_t
sysfs_show_available_clocksources(struct sys_device *dev, char *buf)
{
struct clocksource *src;
char *curr = buf;
spin_lock_irq(&clocksource_lock);
list_for_each_entry(src, &clocksource_list, list) {
curr += sprintf(curr, "%s ", src->name);
}
spin_unlock_irq(&clocksource_lock);
curr += sprintf(curr, "\n");
return curr - buf;
}
-----------------------------------------------------------------------
sysfs_show_current_clocksources() also has the same problem though in practice
the size of current clocksource's name won't exceed PAGE_SIZE.
I fix the bug by using snprintf according to the specification of the kernel
(Version:2.6.24-rc2,File:Documentation/filesystems/sysfs.txt)
Fix sysfs_show_available_clocksources() and sysfs_show_current_clocksources()
buffer overflow problem with snprintf().
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To allow better diagnosis of tick-sched related, especially NOHZ
related problems, we need to know when the last wakeup via an irq
happened and when the CPU left the idle state.
Add two fields (idle_waketime, idle_exittime) to the tick_sched
structure and add them to the timer_list output.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
xtime_cache needs to be updated whenever xtime and or wall_to_monotic
are changed. Otherwise users of xtime_cache might see a stale (and in
the case of timezone changes utterly wrong) value until the next
update happens.
Fixup the obvious places, which miss this update.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Current idle time in kstat is based on jiffies and is coarse grained.
tick_sched.idle_sleeptime is making some attempt to keep track of idle time
in a fine grained manner. But, it is not handling the time spent in
interrupts fully.
Make tick_sched.idle_sleeptime accurate with respect to time spent on
handling interrupts and also add tick_sched.idle_lastupdate, which keeps
track of last time when idle_sleeptime was updated.
This statistics will be crucial for cpufreq-ondemand governor, which can
shed some conservative gaurd band that is uses today while setting the
frequency. The ondemand changes that uses the exact idle time is coming
soon.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I recently noticed on one of my boxes that when synched with an NTP
server, the drift value reported for the system was ~283ppm. While in
some cases, clock hardware can be that bad, it struck me as unusual as
the system was using the acpi_pm clocksource, which is one of the more
trustworthy and accurate clocksources on x86 hardware.
I brought up another system and let it sync to the same NTP server, and
I noticed a similar 280some ppm drift.
In looking at the code, I found that the acpi_pm's constant frequency
was being computed correctly at boot-up, however once the system was up,
even without the ntp daemon running, the clocksource's frequency was
being modified by the clocksource_adjust() function.
Digging deeper, I realized that in the code that keeps track of how much
the clocksource is skewing from the ntp desired time, we were using
different lengths to establish how long an time interval was.
The clocksource was being setup with the following interval:
NTP_INTERVAL_LENGTH = NSEC_PER_SEC/NTP_INTERVAL_FREQ
While the ntp code was using the tick_length_base value:
tick_length_base ~= (tick_usec * NSEC_PER_USEC * USER_HZ)
/NTP_INTERVAL_FREQ
The subtle difference is:
(tick_usec * NSEC_PER_USEC * USER_HZ) != NSEC_PER_SEC
This difference in calculation was causing the clocksource correction
code to apply a correction factor to the clocksource so the two
intervals were the same, however this results in the actual frequency of
the clocksource to be made incorrect. I believe this difference would
affect all clocksources, although to differing degrees depending on the
clocksource resolution.
The issue was introduced when my HZ free ntp patch landed in 2.6.21-rc1,
so my apologies for the mistake, and for not noticing it until now.
The following patch, corrects the clocksource's initialization code so
it uses the same interval length as the code in ntp.c. After applying
this patch, the drift value for the same system went from ~283ppm to
only 2.635ppm.
I believe this patch to be good, however it does affect all arches and
I've only tested on x86, so some caution is advised. I do think it would
be a likely candidate for a stable 2.6.24.x release.
Any thoughts or feedback would be appreciated.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
detect zero event-device multiplicators - they then cause
division-by-zero crashes if a clockevent has been initialized
incorrectly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On x86 the PIT might become an unusable clocksource. Add an unregister
function to provide a possibilty to remove the PIT from the list of
available clock sources.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This way it checks if the clocks are synchronized between CPUs too.
This might be able to detect slowly drifting TSCs which only
go wrong over longer time.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
clocksource_watchdog can use a deferrable timer - reduces wakeups from
idle per second.
Signed-off-by: Parag Warudkar <parag.warudkar@gmail.com>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- getnstimeofday() was just a wrapper around __get_realtime_clock_ts()
- Replace calls to __get_realtime_clock_ts() by calls to getnstimeofday()
- Fix bogus reference to get_realtime_clock_ts(), which never existed
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I was confused by FSEC = 10^15 NSEC statement, plus small whitespace
fixes. When there's copyright, there should be GPL.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Small cleanups to tick-related code. Wrong preempt count is followed
by BUG(), so it is hardly KERN_WARNING.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In order to more easily allow for the scheduler to use timers, clean up
the locking a bit.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need to teach no_hz about the rt throttling because its tick driven.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resolve the following regression of a choppy, almost unusable laptop:
http://lkml.org/lkml/2007/12/7/299http://bugzilla.kernel.org/show_bug.cgi?id=9525
A previous version of the code did the reprogramming of the broadcast
device in the return from idle code. This was removed, but the logic in
tick_handle_oneshot_broadcast() was kept the same.
When a broadcast interrupt happens we signal the expiry to all CPUs
which have an expired event. If none of the CPUs has an expired event,
which can happen in dyntick mode, then we reprogram the broadcast
device. We do not reprogram otherwise, but this is only correct if all
CPUs, which are in the idle broadcast state have been woken up.
The code ignores, that there might be pending not yet expired events on
other CPUs, which are in the idle broadcast state. So the delivery of
those events can be delayed for quite a time.
Change the tick_handle_oneshot_broadcast() function to check for CPUs,
which are in broadcast state and are not woken up by the current event,
and enforce the rearming of the broadcast device for those CPUs.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The hrtimer problem with large relative timeouts resulting in a
negative expiry time went unnoticed as there is no check in the
clockevents_program_event() code. Put a check there with a WARN_ONCE
to avoid such problems in the future.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
David Miller reported soft lockup false-positives that trigger
on NOHZ due to CPUs idling for more than 10 seconds.
The solution is touch the softlockup watchdog when we return from
idle. (by definition we are not 'locked up' when we were idle)
http://bugzilla.kernel.org/show_bug.cgi?id=9409
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Michael Kerrisk reported that a long standing bug in the adjtimex()
system call causes glibc's adjtime(3) function to deliver the wrong
results if 'delta' is NULL.
add the ADJ_OFFSET_SS_READ API detail, which will be used by glibc
to fix this API compatibility bug.
Also see: http://bugzilla.kernel.org/show_bug.cgi?id=6761
[ mingo@elte.hu: added patch description and made it backwards compatible ]
NOTE: the new flag is defined 0xa001 so that it returns -EINVAL on
older kernels - this way glibc can use it safely. Suggested by Ulrich
Drepper.
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix a typo in ntp.c that has caused updating of the persistent (RTC)
clock when synced to NTP to behave erratically.
When debugging a freeze that arises on my AMD64 machines when I
run the ntpd service, I added a number of printk's to monitor the
sync_cmos_clock procedure. I discovered that it was not syncing to
cmos RTC every 11 minutes as documented, but instead would keep trying
every second for hours at a time. The reason turned out to be a typo
in sync_cmos_clock, where it attempts to ensure that
update_persistent_clock is called very close to 500 msec. after a 1
second boundary (required by the PC RTC's spec). That typo referred to
"xtime" in one spot, rather than "now", which is derived from "xtime"
but not equal to it. This makes the test erratic, creating a
"coin-flip" that decides when update_persistent_clock is called - when
it is called, which is rarely, it may be at any time during the one
second period, rather than close to 500 msec, so the value written is
needlessly incorrect, too.
Signed-off-by: David P. Reed
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes sure printk format strings contain no more than a single
line.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch removes the unused
EXPORT_SYMBOL_GPL(tick_nohz_get_sleep_length).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (41 commits)
ACPICA: hw: Don't carry spinlock over suspend
ACPICA: hw: remove use_lock flag from acpi_hw_register_{read, write}
ACPI: cpuidle: port idle timer suspend/resume workaround to cpuidle
ACPI: clean up acpi_enter_sleep_state_prep
Hibernation: Make sure that ACPI is enabled in acpi_hibernation_finish
ACPI: suppress uninitialized var warning
cpuidle: consolidate 2.6.22 cpuidle branch into one patch
ACPI: thinkpad-acpi: skip blanks before the data when parsing sysfs
ACPI: AC: Add sysfs interface
ACPI: SBS: Add sysfs alarm
ACPI: SBS: Add ACPI_PROCFS around procfs handling code.
ACPI: SBS: Add support for power_supply class (and sysfs)
ACPI: SBS: Make SBS reads table-driven.
ACPI: SBS: Simplify data structures in SBS
ACPI: SBS: Split host controller (ACPI0001) from SBS driver (ACPI0002)
ACPI: EC: Add new query handler to list head.
ACPI: Add acpi_bus_generate_event4() function
ACPI: Battery: add sysfs alarm
ACPI: Battery: Add sysfs support
ACPI: Battery: Misc clean-ups, no functional changes
...
Fix up conflicts in drivers/misc/thinkpad_acpi.[ch] manually
kernel/time/clocksource.c: Convert list_for_each to
list_for_each_entry in clocksource_resume(),
sysfs_override_clocksource() and show_available_clocksources()
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Doh, I completely missed that devices marked DUMMY are not running
the set_mode function. So we force broadcasting, but we keep the
local APIC timer running.
Let the clock event layer mark the device _after_ switching it off.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To avoid lock contention, we distribute the sched_timer calls across the
cpus so they do not trigger at the same instant. However, I used NR_CPUS,
which can cause needless grouping on small smp systems depending on your
kernel config. This patch converts to using num_possible_cpus() so we
spread it as evenly as possible on every machine.
Briefly tested w/ NR_CPUS=255 and verified reduced contention.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- remove the no longer required __attribute__((weak)) of xtime_lock
- remove the following no longer used EXPORT_SYMBOL's:
- xtime
- xtime_lock
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
smp_call_function_single() now knows how to call the function on the
current cpu.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
improve performance of sys_time(). sys_time() returns time in seconds,
but it does so by calling do_gettimeofday() and then returning the
tv_sec portion of the GTOD time. But the data structure "xtime", which
is updated by every timer/scheduler tick, already offers HZ granularity
time.
the patch improves the sysbench oltp macrobenchmark by 4-5% on an AMD
dual-core system:
v2.6.23:
#threads
1: transactions: 4073 (407.23 per sec.)
2: transactions: 8530 (852.81 per sec.)
3: transactions: 8321 (831.88 per sec.)
4: transactions: 8407 (840.58 per sec.)
5: transactions: 8070 (806.74 per sec.)
v2.6.23 + sys_time-speedup.patch:
1: transactions: 4281 (428.09 per sec.)
2: transactions: 8910 (890.85 per sec.)
3: transactions: 8659 (865.79 per sec.)
4: transactions: 8676 (867.34 per sec.)
5: transactions: 8532 (852.91 per sec.)
and by 4-5% on an Intel dual-core system too:
2.6.23:
1: transactions: 4560 (455.94 per sec.)
2: transactions: 10094 (1009.30 per sec.)
3: transactions: 9755 (975.36 per sec.)
4: transactions: 9859 (985.78 per sec.)
5: transactions: 9701 (969.72 per sec.)
2.6.23 + sys_time-speedup.patch:
1: transactions: 4779 (477.84 per sec.)
2: transactions: 10103 (1010.14 per sec.)
3: transactions: 10141 (1013.93 per sec.)
4: transactions: 10371 (1036.89 per sec.)
5: transactions: 10178 (1017.50 per sec.)
(the more CPUs the system has, the more speedup this patch gives for
this particular workload.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The 64bit SMP bootup is slightly different to the 32bit one. It enables
the boot CPU local APIC timer before all CPUs are brought up. Some AMD C1E
systems have the C1E feature flag only set in the secondary CPU. Due to
the early enable of the boot CPU local APIC timer the APIC timer is
registered as a fully functional device. When we detect the wreckage during
the bringup of the secondary CPU, we need to force the boot CPU into
broadcast mode.
Add a new notifier reason and implement the force broadcast in the clock
events layer.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change the broadcast timer, if a timer with higher rating becomes available.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The next_event member of the clock event device is used to keep track
of the next periodic event. For one shot only devices it is wrong to
clear the variable, as the next event will be based on it.
Pointed out by Ralf Baechle
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Migration aid to allow preparatory patches which introduce not yet
used parts of clock events code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
commit e5a16b1f9eec0af7cfa0830304b41c1c0833cf9f
Author: Len Brown <len.brown@intel.com>
Date: Tue Oct 2 23:44:44 2007 -0400
cpuidle: shrink diff
processor_idle.c | 440 +++++++++++++++++++++++++++++++++++++++++--
1 file changed, 429 insertions(+), 11 deletions(-)
Signed-off-by: Len Brown <len.brown@intel.com>
commit dfbb9d5aedfb18848a3e0d6f6e3e4969febb209c
Author: Len Brown <len.brown@intel.com>
Date: Wed Sep 26 02:17:55 2007 -0400
cpuidle: reduce diff size
Reduces the cpuidle processor_idle.c diff vs 2.6.22 from this
processor_idle.c | 2006 ++++++++++++++++++++++++++-----------------
1 file changed, 1219 insertions(+), 787 deletions(-)
to this:
processor_idle.c | 502 +++++++++++++++++++++++++++++++++++++++----
1 file changed, 458 insertions(+), 44 deletions(-)
...for the purpose of making the cpuilde patch less invasive
and easier to review.
no functional changes. build tested only.
Signed-off-by: Len Brown <len.brown@intel.com>
commit 889172fc915f5a7fe20f35b133cbd205ce69bf6c
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Sep 13 13:40:05 2007 -0700
cpuidle: Retain old ACPI policy for !CONFIG_CPU_IDLE
Retain the old policy in processor_idle, so that when CPU_IDLE is not
configured, old C-state policy will still be used. This provides a
clean gradual migration path from old ACPI policy to new cpuidle
based policy.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 9544a8181edc7ecc33b3bfd69271571f98ed08bc
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Sep 13 13:39:17 2007 -0700
cpuidle: Configure governors by default
Quoting Len "Do not give an option to users to shoot themselves in the foot".
Remove the configurability of ladder and menu governors as they are
needed for default policy of cpuidle. That way users will not be able to
have cpuidle without any policy loosing all C-state power savings.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8975059a2c1e56cfe83d1bcf031bcf4cb39be743
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:27:07 2007 -0400
CPUIDLE: load ACPI properly when CPUIDLE is disabled
Change the registration return codes for when CPUIDLE
support is not compiled into the kernel. As a result, the ACPI
processor driver will load properly even if CPUIDLE is unavailable.
However, it may be possible to cleanup the ACPI processor driver further
and eliminate some dead code paths.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit e0322e2b58dd1b12ec669bf84693efe0dc2414a8
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:26:06 2007 -0400
CPUIDLE: remove cpuidle_get_bm_activity()
Remove cpuidle_get_bm_activity() and updates governors
accordingly.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 18a6e770d5c82ba26653e53d240caa617e09e9ab
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:58 2007 -0400
CPUIDLE: max_cstate fix
Currently max_cstate is limited to 0, resulting in no idle processor
power management on ACPI platforms. This patch restores the value to
the array size.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1fdc0887286179b40ce24bcdbde663172e205ef0
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:40 2007 -0400
CPUIDLE: handle BM detection inside the ACPI Processor driver
Update the ACPI processor driver to detect BM activity and
limit state entry depth internally, rather than exposing such
requirements to CPUIDLE. As a result, CPUIDLE can drop this
ACPI-specific interface and become more platform independent. BM
activity is now handled much more aggressively than it was in the
original implementation, so some testing coverage may be needed to
verify that this doesn't introduce any DMA buffer under-run issues.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0ef38840db666f48e3cdd2b769da676c57228dd9
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:25:14 2007 -0400
CPUIDLE: menu governor updates
Tweak the menu governor to more effectively handle non-timer
break events. Non-timer break events are detected by comparing the
actual sleep time to the expected sleep time. In future revisions, it
may be more reliable to use the timer data structures directly.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit bb4d74fca63fa96cf3ace644b15ae0f12b7df5a1
Author: Adam Belay <abelay@novell.com>
Date: Tue Aug 21 18:24:40 2007 -0400
CPUIDLE: fix 'current_governor' sysfs entry
Allow the "current_governor" sysfs entry to properly handle
input terminated with '\n'.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit df3c71559bb69b125f1a48971bf0d17f78bbdf47
Author: Len Brown <len.brown@intel.com>
Date: Sun Aug 12 02:00:45 2007 -0400
cpuidle: fix IA64 build (again)
Signed-off-by: Len Brown <len.brown@intel.com>
commit a02064579e3f9530fd31baae16b1fc46b5a7bca8
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:39:27 2007 -0400
cpuidle: Remove support for runtime changing of max_cstate
Remove support for runtime changeability of max_cstate. Drivers can use
use latency APIs.
max_cstate can still be used as a boot time option and dmi override.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0912a44b13adf22f5e3f607d263aed23b4910d7e
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:39:16 2007 -0400
cpuidle: Remove ACPI cstate_limit calls from ipw2100
ipw2100 already has code to use accetable_latency interfaces to limit the
C-state. Remove the calls to acpi_set_cstate_limit and acpi_get_cstate_limit
as they are redundant.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c649a76e76be6bff1fd770d0a775798813a3f6e0
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Sun Aug 12 01:35:39 2007 -0400
cpuidle: compile fix for pause and resume functions
Fix the compilation failure when cpuidle is not compiled in.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Adam Belay <adam.belay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 2305a5920fb8ee6ccec1c62ade05aa8351091d71
Author: Adam Belay <abelay@novell.com>
Date: Thu Jul 19 00:49:00 2007 -0400
cpuidle: re-write
Some portions have been rewritten to make the code cleaner and lighter
weight. The following is a list of changes:
1.) the state name is now included in the sysfs interface
2.) detection, hotplug, and available state modifications are handled by
CPUIDLE drivers directly
3.) the CPUIDLE idle handler is only ever installed when at least one
cpuidle_device is enabled and ready
4.) the menu governor BM code no longer overflows
5.) the sysfs attributes are now printed as unsigned integers, avoiding
negative values
6.) a variety of other small cleanups
Also, Idle drivers are no longer swappable during runtime through the
CPUIDLE sysfs inteface. On i386 and x86_64 most idle handlers (e.g.
poll, mwait, halt, etc.) don't benefit from an infrastructure that
supports multiple states, so I think using a more general case idle
handler selection mechanism would be cleaner.
Signed-off-by: Adam Belay <abelay@novell.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit df25b6b56955714e6e24b574d88d1fd11f0c3ee5
Author: Len Brown <len.brown@intel.com>
Date: Tue Jul 24 17:08:21 2007 -0400
cpuidle: fix IA64 buid
Signed-off-by: Len Brown <len.brown@intel.com>
commit fd6ada4c14488755ff7068860078c437431fbccd
Author: Adrian Bunk <bunk@stusta.de>
Date: Mon Jul 9 11:33:13 2007 -0700
cpuidle: static
make cpuidle_replace_governor() static
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c1d4a2cebcadf2429c0c72e1d29aa2a9684c32e0
Author: Adrian Bunk <bunk@stusta.de>
Date: Tue Jul 3 00:54:40 2007 -0400
cpuidle: static
This patch makes the needlessly global struct menu_governor static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit dbf8780c6e8d572c2c273da97ed1cca7608fd999
Author: Andrew Morton <akpm@linux-foundation.org>
Date: Tue Jul 3 00:49:14 2007 -0400
export symbol tick_nohz_get_sleep_length
ERROR: "tick_nohz_get_sleep_length" [drivers/cpuidle/governors/menu.ko] undefined!
ERROR: "tick_nohz_get_idle_jiffies" [drivers/cpuidle/governors/menu.ko] undefined!
And please be sure to get your changes to core kernel suitably reviewed.
Cc: Adam Belay <abelay@novell.com>
Cc: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 29f0e248e7017be15f99febf9143a2cef00b2961
Author: Andrew Morton <akpm@linux-foundation.org>
Date: Tue Jul 3 00:43:04 2007 -0400
tick.h needs hrtimer.h
It uses hrtimers.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit e40cede7d63a029e92712a3fe02faee60cc38fb4
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:40:34 2007 -0400
cpuidle: first round of documentation updates
Documentation changes based on Pavel's feedback.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 83b42be2efece386976507555c29e7773a0dfcd1
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:39:25 2007 -0400
cpuidle: add rating to the governors and pick the one with highest rating by default
Introduce a governor rating scheme to pick the right governor by default.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit d2a74b8c5e8f22def4709330d4bfc4a29209b71c
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:38:08 2007 -0400
cpuidle: make cpuidle sysfs driver governor switch off by default
Make default cpuidle sysfs to show current_governor and current_driver in
read-only mode. More elaborate available_governors and available_drivers with
writeable current_governor and current_driver interface only appear with
"cpuidle_sysfs_switch" boot parameter.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1f60a0e80bf83cf6b55c8845bbe5596ed8f6307b
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:37:00 2007 -0400
cpuidle: menu governor: change the early break condition
Change the C-state early break out algorithm in menu governor.
We only look at early breakouts that result in wakeups shorter than idle
state's target_residency. If such a breakout is frequent enough, eliminate
the particular idle state upto a timeout period.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 45a42095cf64b003b4a69be3ce7f434f97d7af51
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:35:38 2007 -0400
cpuidle: fix uninitialized variable in sysfs routine
Fix the uninitialized usage of ret.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 80dca7cdba3e6ee13eae277660873ab9584eb3be
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:34:16 2007 -0400
cpuidle: reenable /proc/acpi//power interface for the time being
Keep /proc/acpi/processor/CPU*/power around for a while as powertop depends
on it. It will be marked deprecated and removed in future. powertop can use
cpuidle interfaces instead.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 589c37c2646c5e3813a51255a5ee1159cb4c33fc
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Jul 3 00:32:37 2007 -0400
cpuidle: menu governor and hrtimer compile fix
Compile fix for menu governor.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0ba80bd9ab3ed304cb4f19b722e4cc6740588b5e
Author: Len Brown <len.brown@intel.com>
Date: Thu May 31 22:51:43 2007 -0400
cpuidle: build fix - cpuidle vs ipw2100 module
ERROR: "acpi_set_cstate_limit" [drivers/net/wireless/ipw2100.ko] undefined!
Signed-off-by: Len Brown <len.brown@intel.com>
commit d7d8fa7f96a7f7682be7c6cc0cc53fa7a18c3b58
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:47:07 2007 -0400
cpuidle: add the 'menu' governor
Here is my first take at implementing an idle PM governor that takes
full advantage of NO_HZ. I call it the 'menu' governor because it
considers the full list of idle states before each entry.
I've kept the implementation fairly simple. It attempts to guess the
next residency time and then chooses a state that would meet at least
the break-even point between power savings and entry cost. To this end,
it selects the deepest idle state that satisfies the following
constraints:
1. If the idle time elapsed since bus master activity was detected
is below a threshold (currently 20 ms), then limit the selection
to C2-type or above.
2. Do not choose a state with a break-even residency that exceeds
the expected time remaining until the next timer interrupt.
3. Do not choose a state with a break-even residency that exceeds
the elapsed time between the last pair of break events,
excluding timer interrupts.
This governor has an advantage over "ladder" governor because it
proactively checks how much time remains until the next timer interrupt
using the tick infrastructure. Also, it handles device interrupt
activity more intelligently by not including timer interrupts in break
event calculations. Finally, it doesn't make policy decisions using the
number of state entries, which can have variable residency times (NO_HZ
makes these potentially very large), and instead only considers sleep
time deltas.
The menu governor can be selected during runtime using the cpuidle sysfs
interface like so:
"echo "menu" > /sys/devices/system/cpu/cpuidle/current_governor"
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit a4bec7e65aa3b7488b879d971651cc99a6c410fe
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:47:03 2007 -0400
cpuidle: export time until next timer interrupt using NO_HZ
Expose information about the time remaining until the next
timer interrupt expires by utilizing the dynticks infrastructure.
Also modify the main idle loop to allow dynticks to handle
non-interrupt break events (e.g. DMA). Finally, expose sleep ticks
information to external code. Thomas Gleixner is responsible for much
of the code in this patch. However, I've made some additional changes,
so I'm probably responsible if there are any bugs or oversights :)
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 2929d8996fbc77f41a5ff86bb67cdde3ca7d2d72
Author: Adam Belay <abelay@novell.com>
Date: Sat Mar 24 03:46:58 2007 -0400
cpuidle: governor API changes
This patch prepares cpuidle for the menu governor. It adds an optional
stage after idle state entry to give the governor an opportunity to
check why the state was exited. Also it makes sure the idle loop
returns after each state entry, allowing the appropriate dynticks code
to run.
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 3a7fd42f9825c3b03e364ca59baa751bb350775f
Author: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Apr 26 00:03:59 2007 -0700
cpuidle: hang fix
Prevent hang on x86-64, when ACPI processor driver is added as a module on
a system that does not support C-states.
x86-64 expects all idle handlers to enable interrupts before returning from
idle handler. This is due to enter_idle(), exit_idle() races. Make
cpuidle_idle_call() confirm to this when there is no pm_idle_old.
Also, cpuidle look at the return values of attch_driver() and set
current_driver to NULL if attach fails on all CPUs.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 4893339a142afbd5b7c01ffadfd53d14746e858e
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:09 2007 +0800
cpuidle: add support for max_cstate limit
With CPUIDLE framework, the max_cstate (to limit max cpu c-state)
parameter is ingored. Some systems require it to ignore C2/C3
and some drivers like ipw require it too.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 43bbbbe1cb998cbd2df656f55bb3bfe30f30e7d1
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:13 2007 +0800
cpuidle: add cpuidle_fore_redetect_devices API
add cpuidle_force_redetect_devices API,
which forces all CPU redetect idle states.
Next patch will use it.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit d1edadd608f24836def5ec483d2edccfb37b1d19
Author: Shaohua Li <shaohua.li@intel.com>
Date: Thu Apr 26 10:40:01 2007 +0800
cpuidle: fix sysfs related issue
Fix the cpuidle sysfs issue.
a. make kobject dynamicaly allocated
b. fixed sysfs init issue to avoid suspend/resume issue
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 7169a5cc0d67b263978859672e86c13c23a5570d
Author: Randy Dunlap <randy.dunlap@oracle.com>
Date: Wed Mar 28 22:52:53 2007 -0400
cpuidle: 1-bit field must be unsigned
A 1-bit bitfield has no room for a sign bit.
drivers/cpuidle/governors/ladder.c:54:16: error: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 4658620158dc2fbd9e4bcb213c5b6fb5d05ba7d4
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Wed Mar 28 22:52:41 2007 -0400
cpuidle: fix boot hang
Patch for cpuidle boot hang reported by Larry Finger here.
http://www.ussg.iu.edu/hypermail/linux/kernel/0703.2/2025.html
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit c17e168aa6e5fe3851baaae8df2fbc1cf11443a9
Author: Len Brown <len.brown@intel.com>
Date: Wed Mar 7 04:37:53 2007 -0500
cpuidle: ladder does not depend on ACPI
build fix for CONFIG_ACPI=n
In file included from drivers/cpuidle/governors/ladder.c:21:
include/acpi/processor.h:88: error: expected specifier-qualifier-list before âacpi_integerâ
include/acpi/processor.h:106: error: expected specifier-qualifier-list before âacpi_integerâ
include/acpi/processor.h:168: error: expected specifier-qualifier-list before âacpi_handleâ
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8c91d958246bde68db0c3f0c57b535962ce861cb
Author: Adrian Bunk <bunk@stusta.de>
Date: Tue Mar 6 02:29:40 2007 -0800
cpuidle: make code static
This patch makes the following needlessly global code static:
- driver.c: __cpuidle_find_driver()
- governor.c: __cpuidle_find_governor()
- ladder.c: struct ladder_governor
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 0c39dc3187094c72c33ab65a64d2017b21f372d2
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Wed Mar 7 02:38:22 2007 -0500
cpu_idle: fix build break
This patch fixes a build breakage with !CONFIG_HOTPLUG_CPU and
CONFIG_CPU_IDLE.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 8112e3b115659b07df340ef170515799c0105f82
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Tue Mar 6 02:29:39 2007 -0800
cpuidle: build fix for !CPU_IDLE
Fix the compile issues when CPU_IDLE is not configured.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 1eb4431e9599cd25e0d9872f3c2c8986821839dd
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:54:57 2007 -0800
cpuidle take2: Basic documentation for cpuidle
Documentation for cpuidle infrastructure
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit ef5f15a8b79123a047285ec2e3899108661df779
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:54:03 2007 -0800
cpuidle take2: Hookup ACPI C-states driver with cpuidle
Hookup ACPI C-states onto generic cpuidle infrastructure.
drivers/acpi/procesor_idle.c is now a ACPI C-states driver that registers as
a driver in cpuidle infrastructure and the policy part is removed from
drivers/acpi/processor_idle.c. We use governor in cpuidle instead.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
commit 987196fa82d4db52c407e8c9d5dec884ba602183
Author: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Date: Thu Feb 22 13:52:57 2007 -0800
cpuidle take2: Core cpuidle infrastructure
Announcing 'cpuidle', a new CPU power management infrastructure to manage
idle CPUs in a clean and efficient manner.
cpuidle separates out the drivers that can provide support for multiple types
of idle states and policy governors that decide on what idle state to use
at run time.
A cpuidle driver can support multiple idle states based on parameters like
varying power consumption, wakeup latency, etc (ACPI C-states for example).
A cpuidle governor can be usage model specific (laptop, server,
laptop on battery etc).
Main advantage of the infrastructure being, it allows independent development
of drivers and governors and allows for better CPU power management.
A huge thanks to Adam Belay and Shaohua Li who were part of this mini-project
since its beginning and are greatly responsible for this patchset.
This patch:
Core cpuidle infrastructure.
Introduces a new abstraction layer for cpuidle:
* which manages drivers that can support multiple idles states. Drivers
can be generic or particular to specific hardware/platform
* allows pluging in multiple policy governors that can take idle state policy
decision
* The core also has a set of sysfs interfaces with which administrato can know
about supported drivers and governors and switch them at run time.
Signed-off-by: Adam Belay <abelay@novell.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When using /proc/timer_stats on ppc64 I noticed the events/sec field wasnt
accurate. Sometimes the integer part was incorrect due to rounding (we
werent taking the fractional seconds into consideration).
The fraction part is also wrong, we need to pad the printf statement and
take the bottom three digits of 1000 times the value.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In a desparate attempt to fix the suspend/resume problem on Andrews
VAIO I added a workaround which enforced the broadcast of the oneshot
timer on resume. This was actually resolving the problem on the VAIO
but was just a stupid workaround, which was not tackling the root
cause: the assignement of lower idle C-States in the ACPI processor_idle
code. The cpuidle patches, which utilize the dynamic tick feature and
go faster into deeper C-states exposed the problem again. The correct
solution is the previous patch, which prevents lower C-states across
the suspend/resume.
Remove the enforcement code, including the conditional broadcast timer
arming, which helped to pamper over the real problem for quite a time.
The oneshot broadcast flag for the cpu, which runs the resume code can
never be set at the time when this code is executed. It only gets set,
when the CPU is entering a lower idle C-State.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Taking a cpu offline removes the cpu from the online mask before the
CPU_DEAD notification is done. The clock events layer does the cleanup
of the dead CPU from the CPU_DEAD notifier chain. tick_do_timer_cpu is
used to avoid xtime lock contention by assigning the task of jiffies
xtime updates to one CPU. If a CPU is taken offline, then this
assignment becomes stale. This went unnoticed because most of the time
the offline CPU went dead before the online CPU reached __cpu_die(),
where the CPU_DEAD state is checked. In the case that the offline CPU did
not reach the DEAD state before we reach __cpu_die(), the code in there
goes to sleep for 100ms. Due to the stale time update assignment, the
system is stuck forever.
Take the assignment away when a cpu is not longer in the cpu_online_mask.
We do this in the last call to tick_nohz_stop_sched_tick() when the offline
CPU is on the way to the final play_dead() idle entry.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When a cpu goes offline it is removed from the broadcast masks. If the
mask becomes empty the code shuts down the broadcast device. This is
wrong, because the broadcast device needs to be ready for the online
cpu going idle (into a c-state, which stops the local apic timer).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The jinxed VAIO refuses to resume without hitting keys on the keyboard
when this is not enforced. It is unclear why the cpu ends up in a lower
C State without notifying the clock events layer, but enforcing the
oneshot broadcast here is safe.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Timekeeping resume adjusts xtime by adding the slept time in seconds and
resets the reference value of the clock source (clock->cycle_last).
clock->cycle last is used to calculate the delta between the last xtime
update and the readout of the clock source in __get_nsec_offset(). xtime
plus the offset is the current time. The resume code ignores the delta
which had already elapsed between the last xtime update and the actual
time of suspend. If the suspend time is short, then we can see time
going backwards on resume.
Suspend:
offs_s = clock->read() - clock->cycle_last;
now = xtime + offs_s;
timekeeping_suspend_time = read_rtc();
Resume:
sleep_time = read_rtc() - timekeeping_suspend_time;
xtime.tv_sec += sleep_time;
clock->cycle_last = clock->read();
offs_r = clock->read() - clock->cycle_last;
now = xtime + offs_r;
if sleep_time_seconds == 0 and offs_r < offs_s, then time goes
backwards.
Fix this by storing the offset from the last xtime update and add it to
xtime during resume, when we reset clock->cycle_last:
sleep_time = read_rtc() - timekeeping_suspend_time;
xtime.tv_sec += sleep_time;
xtime += offs_s; /* Fixup xtime offset at suspend time */
clock->cycle_last = clock->read();
offs_r = clock->read() - clock->cycle_last;
now = xtime + offs_r;
Thanks to Marcelo for tracking this down on the OLPC and providing the
necessary details to analyze the root cause.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Tosatti <marcelo@kvack.org>
Lockdep complains about the access of rtc in timekeeping_suspend
inside the interrupt disabled region of the write locked xtime lock.
Move the access outside.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <johnstul@us.ibm.com>
Seems to me that this timer will only get started on platforms that say
they don't want it?
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Gabriel Paubert <paubert@iram.es>
Cc: Zachary Amsden <zach@vmware.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I find a function(clockevents_unregister_notifier) which is not called by
anything in tree.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This avoids xtime lag seen with dynticks, because while 'xtime' itself
is still not updated often, we keep a 'xtime_cache' variable around that
contains the approximate real-time that _is_ updated each time we do a
'update_wall_time()', and is thus never off by more than one tick.
IOW, this restores the original semantics for 'xtime' users, as long as
you use the proper abstraction functions (ie 'current_kernel_time()' or
'get_seconds()' depending on whether you want a timespec or just the
seconds field).
[ Updated Patch. As penance for my sins I've also yanked another #ifdef
that was added to avoid the xtime lag w/ hrtimers. ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This avoids use of the kernel-internal "xtime" variable directly outside
of the actual time-related functions. Instead, use the helper functions
that we already have available to us.
This doesn't actually change any behaviour, but this will allow us to
fix the fact that "xtime" isn't updated very often with CONFIG_NO_HZ
(because much of the realtime information is maintained as separate
offsets to 'xtime'), which has caused interfaces that use xtime directly
to get a time that is out of sync with the real-time clock by up to a
third of a second or so.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i386 and sparc64 have the identical code to update the cmos clock. Move it
into kernel/time/ntp.c as there are other architectures coming along with the
same requirements.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: David Miller <davem@davemloft.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some more debug information to the hrtimer and clock events code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After discussing w/ Thomas over IRC, it seems the issue is the sched tick
fires on every cpu at the same time, causing extra lock contention.
This smaller change, adds an extra offset per cpu so the ticks don't line up.
This patch also drops the idle latency from 40us down to under 20us.
Signed-off-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a device is replaced by a better rated device, then the broadcast
mode needs to be evaluated again. When the new device has no requirement
for broadcasting, then the broadcast bits for the CPU must be cleared.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to make sure, that the clockevent devices are resumed, before
the tick is resumed. The current resume logic does not guarantee this.
Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock
event devices before resuming the tick / oneshot functionality.
Fixup the existing users.
Thanks to Nigel Cunningham for tracking down a long standing thinko,
which affected the jinxed VAIO.
[akpm@linux-foundation.org: xen build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove time_interpolator code (This is generic code, but
only user was ia64. It has been superseded by the
CONFIG_GENERIC_TIME code).
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Peter Keilty <peter.keilty@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
clocksource_adjust() has a clock argument, which shadows the file global clock
variable. Fix this up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KSYM_NAME_LEN is peculiar in that it does not include the space for the
trailing '\0', forcing all users to use KSYM_NAME_LEN + 1 when allocating
buffer. This is nonsense and error-prone. Moreover, when the caller
forgets that it's very likely to subtly bite back by corrupting the stack
because the last position of the buffer is always cleared to zero.
This patch increments KSYM_NAME_LEN by one and updates code accordingly.
* off-by-one bug in asm-powerpc/kprobes.h::kprobe_lookup_name() macro
is fixed.
* Where MODULE_NAME_LEN and KSYM_NAME_LEN were used together,
MODULE_NAME_LEN was treated as if it didn't include space for the
trailing '\0'. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Paulo Marques <pmarques@grupopie.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I forgot to remove capability.h from mm.h while removing sched.h! This
patch remedies that, because the only inline function which was using
CAP_something was made out of line.
Cross-compile tested without regressions on:
all powerpc defconfigs
all mips defconfigs
all m68k defconfigs
all arm defconfigs
all ia64 defconfigs
alpha alpha-allnoconfig alpha-defconfig alpha-up
arm
i386 i386-allnoconfig i386-defconfig i386-up
ia64 ia64-allnoconfig ia64-defconfig ia64-up
m68k
mips
parisc parisc-allnoconfig parisc-defconfig parisc-up
powerpc powerpc-up
s390 s390-allnoconfig s390-defconfig s390-up
sparc sparc-allnoconfig sparc-defconfig sparc-up
sparc64 sparc64-allnoconfig sparc64-defconfig sparc64-up
um-x86_64
x86_64 x86_64-allnoconfig x86_64-defconfig x86_64-up
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a flag in /proc/timer_stats to indicate deferrable timers. This will
let developers/users to differentiate between types of tiemrs in
/proc/timer_stats.
Deferrable timer and normal timer will appear in /proc/timer_stats as below.
10D, 1 swapper queue_delayed_work_on (delayed_work_timer_fn)
10, 1 swapper queue_delayed_work_on (delayed_work_timer_fn)
Also version of timer_stats changes from v0.1 to v0.2
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not called by anything in tree.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commits
411187fb05 (GTOD: persistent clock support)
c1d370e167 (i386: use GTOD persistent clock
support)
changed the monotonic time so that it no longer jumps after resume, but it's
not possible to use it for boot time and process start time calculations then.
Also, the uptime no longer increases during suspend.
I add a variable to track the wall_to_monotonic changes, a function to get the
real boot time and a function to get the boot based time from the monotonic
one.
[akpm@linux-foundation.org: remove exports, add comment]
Signed-off-by: Tomas Janousek <tjanouse@redhat.com>
Cc: Tomas Smetana <tsmetana@redhat.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clock_was_set() call in seconds_overflow() which happens only when
leap seconds are inserted / deleted is wrong in two aspects:
1. it results in a call to on_each_cpu() with interrupts disabled
2. it is potential deadlock source vs. call_lock in smp_call_function()
The only possible side effect of the removal might be, that an absolute
CLOCK_REALTIME timer fires 1 second too late, in the rare case of leap
second deletion and an absolute CLOCK_REALTIME timer which expires in
the affected time frame. It will never fire too early.
This was probably observed by the reporter of a June 30th -> July 1st
hang: http://lkml.org/lkml/2007/7/3/103
A similar problem was observed by Dave Jones, who provided a screen shot
with a lockdep back trace, which allowed to analyse the problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make timer-stats have almost zero overhead when enabled in the config but
not used. (this way distros can enable it more easily)
Also update the documentation about overhead of timer_stats - it was
written for the first version which had a global lock and a linear list
walk based lookup ;-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix two races in the timer stats lookup code. One by ensuring that the
initialization of a new entry is finished upon insertion of that entry.
The other by cleaning up the hash table when the entries array is cleared,
so that we don't have any "pre-inserted" entries.
Thanks to Eric Dumazet for reminding me of the memory barriers.
Signed-off-by: Bjorn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: Ian Kumlien <pomac@vapor.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_next_timer_interrupt() returns a delta of (LONG_MAX > 1) in case
there is no timer pending. On 64 bit machines this results in a
multiplication overflow in tick_nohz_stop_sched_tick().
Reported by: Dave Miller <davem@davemloft.net>
Make the return value a constant and limit the return value to a 32 bit
value.
When the max timeout value is returned, we can safely stop the tick
timer device. The max jiffies delta results in a 12 days timeout for
HZ=1000.
In the long term the get_next_timer_interrupt() code needs to be
reworked to return ktime instead of jiffies, but we have to wait until
the last users of the original NO_IDLE_HZ code are converted.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The warning in the NOHZ code, which triggers when a CPU goes idle with
softirqs pending can fill up the logs quite quickly. Rate limit the output
until we found the root cause of that problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Booting a SMP kernel with maxcpus=1 on a SMP system leads to a hard hang,
because ACPI ignores the maxcpus setting and sends timer broadcast info for
the offline CPUs. This results in a stuck for ever call to
smp_call_function_single() on an offline CPU.
Ignore the bogus information and print a kernel error to remind ACPI
folks to fix it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lockdep complains about the lock nesting of clocksource and watchdog lock
in the resume path.
Change the resume marker to a bit operation and remove the lock from this
path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The time keeping code move to kernel/time/timekeeping.c broke the
clocksource resume logic patch, which got applied to the old file by a
fuzzy application. Fix it up and move the clocksource_resume() call to
the appropriate place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ tssk, tssk, everybody should use --fuzz=0 ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to make sure that the clocksources are resumed, when timekeeping is
resumed. The current resume logic does not guarantee this.
Add a resume function pointer to the clocksource struct, so clocksource
drivers which need to reinitialize the clocksource can provide a resume
function.
Add a resume function, which calls the maybe available clocksource resume
functions and resets the watchdog function, so a stable TSC can be used
accross suspend/resume.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
u64 and s64 are not necessarily 'long long' on some 64-bit
platforms, so explicit the type to kill the compiler warnings.
Also consistently use '%Lu' which is unsigned.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's more that need fixing, and fix my own subject spelling error too.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the process idle load balancing in the presence of dynticks. cpus for
which ticks are stopped will sleep till the next event wakes it up.
Potentially these sleeps can be for large durations and during which today,
there is no periodic idle load balancing being done.
This patch nominates an owner among the idle cpus, which does the idle load
balancing on behalf of the other idle cpus. And once all the cpus are
completely idle, then we can stop this idle load balancing too. Checks added
in fast path are minimized. Whenever there are busy cpus in the system, there
will be an owner(idle cpu) doing the system wide idle load balancing.
Open items:
1. Intelligent owner selection (like an idle core in a busy package).
2. Merge with rcu's nohz_cpu_mask?
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While the !highres/!dyntick code assigns the duty of the do_timer() call to
one specific CPU, this was dropped in the highres/dyntick part during
development.
Steven Rostedt discovered the xtime lock contention on highres/dyntick due
to several CPUs trying to update jiffies.
Add the single CPU assignement back. In the dyntick case this needs to be
handled carefully, as the CPU which has the do_timer() duty must drop the
assignement and let it be grabbed by another CPU, which is active.
Otherwise the do_timer() calls would not happen during the long sleep.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Mark Lord <mlord@pobox.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kallsyms_lookup() can go iterating over modules list unprotected which is OK
for emergency situations (oops), but not OK for regular stuff like
/proc/*/wchan.
Introduce lookup_symbol_name()/lookup_module_symbol_name() which copy symbol
name into caller-supplied buffer or return -ERANGE. All copying is done with
module_mutex held, so...
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several kallsyms_lookup() pass dummy arguments but only need, say, module's
name. Make kallsyms_lookup() accept NULLs where possible.
Also, makes picture clearer about what interfaces are needed for all symbol
resolving business.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the timekeeping code out of kernel/timer.c and into
kernel/time/timekeeping.c. I made no cleanups or other changes in transit.
[akpm@linux-foundation.org: build fix]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In debugging a problem w/ the -rt tree, I noticed that on systems that mark
the tsc as unstable before it is registered, the TSC would still be
selected and used for a short period of time. Digging in it looks to be a
result of the mix of the clocksource list changes and my clocksource
initialization changes.
With the -rt tree, using a bad TSC, even for a short period of time can
results in a hang at boot. I was not able to reproduce this hang w/
mainline, but I'm not completely certain that someone won't trip on it.
This patch resolves the issue by initializing the jiffies clocksource
earlier so a bad TSC won't get selected just because nothing else is yet
registered.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've been seeing some odd NTP behavior recently on a few boxes and
finally narrowed it down to time_offset overflowing when converted to
SHIFT_UPDATE units (which was a side effect from my HZfreeNTP patch).
This patch converts time_offset from a long to a s64 which resolves the
issue.
[tglx@linutronix.de: signedness fixes]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current sysfs support of clockevents does not obey the "only one
value per file" rule.
The real fix is not 2.6.21 material. Therefor remove the sysfs support
for now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The watchdog implementation excludes low res / non continuous
clocksources from being selected as a watchdog reference
unintentionally.
Allow using jiffies/PIT as a watchdog reference as long as no better
clocksource is available. This is necessary to detect TSC breakage on
systems, which have no pmtimer/hpet.
The main goal of the initial patch (preventing to switch to highres/nohz
when no reliable fallback clocksource is available) is still guaranteed
by the checks in clocksource_watchdog().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the print formatting of three unsigned long fields in /proc/timer_list,
which are currently being formatted as signed long.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I finally found a dual core box, which survives suspend/resume without
crashing in the middle of nowhere. Sigh, I never figured out from the
code and the bug reports what's going on.
The observed hangs are caused by a stale state transition of the clock
event devices, which keeps the RCU synchronization away from completion,
when the non boot CPU is brought back up.
The suspend/resume in oneshot mode needs the similar care as the
periodic mode during suspend to RAM. My assumption that the state
transitions during the different shutdown/bringups of s2disk would go
through the periodic boot phase and then switch over to highres resp.
nohz mode were simply wrong.
Add the appropriate suspend / resume handling for the non periodic
modes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The programming of periodic tick devices needs to be saved/restored
across suspend/resume - otherwise we might end up with a system coming
up that relies on getting a PIT (or HPET) interrupt, while those devices
default to 'no interrupts' after powerup. (To confuse things it worked
to a certain degree on some systems because the lapic gets initialized
as a side-effect of SMP bootup.)
This suspend / resume thing was dropped unintentionally during the
last-minute -mm code reshuffling.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resolves the issue found here:
http://bugme.osdl.org/show_bug.cgi?id=7426
The basic summary is:
Currently we register most of i386/x86_64 clocksources at module_init
time. Then we enable clocksource selection at late_initcall time. This
causes some problems for drivers that use gettimeofday for init
calibration routines (specifically the es1968 driver in this case),
where durring module_init, the only clocksource available is the low-res
jiffies clocksource. This may cause slight calibration errors, due to
the small sampling time used.
It should be noted that drivers that require fine grained time may not
function on architectures that do not have better then jiffies
resolution timekeeping (there are a few). However, this does not
discount the reasonable need for such fine-grained timekeeping at init
time.
Thus the solution here is to register clocksources earlier (ideally when
the hardware is being initialized), and then we enable clocksource
selection at fs_initcall (before device_initcall).
This patch should probably get some testing time in -mm, since
clocksource selection is one of the most important issues for correct
timekeeping, and I've only been able to test this on a few of my own
boxes.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When clockevents_program_event() is given an expire time in the
past, it does not update dev->next_event, so this looping code
would loop forever once the first in-the-past expiration time
was used.
Keep advancing "next" locally to fix this bug.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BUG_ON() in tick_nohz_stop_sched_tick() triggers on some boxen.
Remove the BUG_ON and print information about the pending softirq
to allow better debugging of the problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a CPU is needed for RCU the tick has to continue even when it was
stopped before.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement high resolution timers on top of the hrtimers infrastructure and the
clockevents / tick-management framework. This provides accurate timers for
all hrtimer subsystem users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With Ingo Molnar <mingo@elte.hu>
Add functions to provide dynamic ticks and high resolution timers. The code
which keeps track of jiffies and handles the long idle periods is shared
between tick based and high resolution timer based dynticks. The dyntick
functionality can be disabled on the kernel commandline. Provide also the
infrastructure to support high resolution timers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With Ingo Molnar <mingo@elte.hu>
Add broadcast functionality, so per cpu clock event devices can be registered
as dummy devices or switched from/to broadcast on demand. The broadcast
function distributes the events via the broadcast function of the clock event
device. This is primarily designed to replace the switch apic timer to / from
IPI in power states, where the apic stops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With Ingo Molnar <mingo@elte.hu>
The tick-management code is the first user of the clockevents layer. It takes
clock event devices from the clock events core and uses them to provide the
periodic tick.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures register their clock event devices, in the clock events core.
Users of the clockevents core can get clock event devices for their use. The
clockevents core code provides notification mechanisms for various clock
related management events.
This allows to control the clock event devices without the architectures
having to worry about the details of function assignment. This is also a
preliminary for high resolution timers and dynamic ticks to allow the core
code to control the clock functionality without intrusive changes to the
architecture code.
[Fixes-by: Ingo Molnar <mingo@elte.hu>]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TSC needs to be verified against another clocksource. Instead of using
hardwired assumptions of available hardware, provide a generic verification
mechanism. The verification uses the best available clocksource and handles
the usability for high resolution timers / dynticks of the clocksource which
needs to be verified.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Using a flag filed allows to encode more than one information into a variable.
Preparatory patch for the generic clocksource verification.
[mingo@elte.hu: convert vmitime.c to the new clocksource flag]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enqueue clocksources in rating order to make selection of the clocksource
easier. Also check the match with an user override at enqueue time.
Preparatory patch for the generic clocksource verification.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Distangle the NTP update from HZ. This is necessary for dynamic tick enabled
kernels.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kernel/time/clocksource.c needs struct task_struct on m68k.
Because it uses spin_unlock_irq(), which, on m68k, uses hardirq_count(), which
uses preempt_count(), which needs to dereference struct task_struct, we
have to include sched.h. Because it would cause a loop inclusion, we
cannot include sched.h in any other of asm-m68k/system.h,
linux/thread_info.h, linux/hardirq.h, which leaves this ugly include in
a C file as the only simple solution.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mostly changing alignment. Just some general cleanup.
[akpm@osdl.org: build fix]
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Simply adds some ifdefs to remove clocksoure sysfs code when CONFIG_SYSFS
isn't turn on.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I notice that the code which implements adjtime clears the time_adjust
value before using it. The attached patch makes the obvious fix.
Acked-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Jim Houston <jim.houston@ccur.com>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid possible PIT livelock issues seen on SMP systems (and reported by
Andi), by not allowing it as a clocksource on SMP boxes.
However, since the PIT may no longer be present, we have to properly handle
the cases where SMP systems have TSC skew and fall back from the TSC.
Since the PIT isn't there, it would "fall back" to the TSC again. So this
changes the jiffies rating to 1, and the TSC-bad rating value to 0.
Thus you will get the following behavior priority on i386 systems:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if UP]
jiffies
Rather then the current more complicated:
tsc [if present & stable]
hpet [if present]
cyclone [if present]
acpi_pm [if present]
pit [if cpus < 4]
tsc [if present & unstable]
jiffies
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the following possible cleanups:
- make the following needlessly global function static:
- ntp_update_frequency()
- make the following needlessly global variables static:
- time_state
- time_offset
- time_constant
- time_reftime
- remove the following read-only global variable:
- time_precision
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts the kernel ntp model into a model which matches the nanokernel
reference implementations. The previous patches already increased the
resolution and precision of the computations, so that this conversion becomes
quite simple.
<linux@horizon.com> explains:
The original NTP kernel interface was defined in units of microseconds.
That's what Linux implements. As computers have gotten faster and can now
split microseconds easily, a new kernel interface using nanosecond units was
defined ("the nanokernel", confusing as that name is to OS hackers), and
there's an STA_NANO bit in the adjtimex() status field to tell the application
which units it's using.
The current ntpd supports both, but Linux loses some possible timing
resolution because of quantization effects, and the ntpd hackers would really
like to be able to drop the backwards compatibility code.
Ulrich Windl has been maintaining a patch set to do the conversion for years,
but it's hard to keep in sync.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts time_freq to a scaled nsec value and adds around 6bit of extra
resolution. This pushes the time_freq to its 32bit limits so the calculatons
have to be done with 64bit.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
time_tolerance isn't changed at all in the kernel, so simply remove it, this
simplifies the next patch, as it avoids a number of conversions.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This folds update_ntp_one_tick() into second_overflow() and adds time_adjust
to the tick length, this makes time_next_adjust unnecessary. This slightly
changes the adjtime() behaviour, instead of applying it to the next tick, it's
applied to the next second.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This converts time_offset into a scaled per tick value. This avoids now
completely the crude compensation in second_overflow().
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
