The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/usb/gadget/udc/trace files follows this syntax, but
the content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc.
For e.g., running scripts/kernel-doc -none drivers/usb/gadget/udc/trace.h
emits:
warning: expecting prototype for udc.c(). Prototype was for TRACE_SYSTEM() instead
Provide a simple fix by replacing this occurrence with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Link: https://lore.kernel.org/r/20210522115227.9977-1-yashsri421@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb3_start_pipen() is called by renesas_usb3_ep_queue() and
usb3_request_done_pipen() so that usb3_start_pipen() is possible
to cause a race when getting usb3_first_req like below:
renesas_usb3_ep_queue()
spin_lock_irqsave()
list_add_tail()
spin_unlock_irqrestore()
usb3_start_pipen()
usb3_first_req = usb3_get_request() --- [1]
--- interrupt ---
usb3_irq_dma_int()
usb3_request_done_pipen()
usb3_get_request()
usb3_start_pipen()
usb3_first_req = usb3_get_request()
...
(the req is possible to be finished in the interrupt)
The usb3_first_req [1] above may have been finished after the interrupt
ended so that this driver caused to start a transfer wrongly. To fix this
issue, getting/checking the usb3_first_req are under spin_lock_irqsave()
in the same section.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210524060155.1178724-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows
that, in the worse scenario, could lead to heap overflows.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20210513193353.GA196565@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to store the dentry for a fixed filename that we have
the string for. So just have debugfs look it up when we need it to
remove the file, no need to store it anywhere locally.
Note, this driver is broken in that debugfs will not work for more than
one instance of the device it supports. But given that this patch does
not change that, and no one has ever seemed to notice, it must not be an
issue...
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20210518162035.3697860-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quieten implicit-fallthrough warnings in fsl_qe_udc.c:
../drivers/usb/gadget/udc/fsl_qe_udc.c: In function 'qe_ep_init':
../drivers/usb/gadget/udc/fsl_qe_udc.c:542:37: warning: this statement may fall through [-Wimplicit-fallthrough=]
542 | if ((max == 128) || (max == 256) || (max == 512))
../drivers/usb/gadget/udc/fsl_qe_udc.c:563:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
563 | if (max <= 1024)
../drivers/usb/gadget/udc/fsl_qe_udc.c:566:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
566 | if (max <= 64)
../drivers/usb/gadget/udc/fsl_qe_udc.c:580:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
580 | if (max <= 1024)
../drivers/usb/gadget/udc/fsl_qe_udc.c:596:5: warning: this statement may fall through [-Wimplicit-fallthrough=]
596 | switch (max) {
This basically just documents what is currently being done.
If any of them need to do something else, just say so or
even make the change.
Cc: Li Yang <leoyang.li@nxp.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20210428040855.25907-1-rdunlap@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a general protection fault reported by syzbot due to a race between
gadget_setup() and gadget_unbind() in raw_gadget.
The gadget core is supposed to guarantee that there won't be any more
callbacks to the gadget driver once the driver's unbind routine is
called. That guarantee is enforced in usb_gadget_remove_driver as
follows:
usb_gadget_disconnect(udc->gadget);
if (udc->gadget->irq)
synchronize_irq(udc->gadget->irq);
udc->driver->unbind(udc->gadget);
usb_gadget_udc_stop(udc);
usb_gadget_disconnect turns off the pullup resistor, telling the host
that the gadget is no longer connected and preventing the transmission
of any more USB packets. Any packets that have already been received
are sure to processed by the UDC driver's interrupt handler by the time
synchronize_irq returns.
But this doesn't work with dummy_hcd, because dummy_hcd doesn't use
interrupts; it uses a timer instead. It does have code to emulate the
effect of synchronize_irq, but that code doesn't get invoked at the
right time -- it currently runs in usb_gadget_udc_stop, after the unbind
callback instead of before. Indeed, there's no way for
usb_gadget_remove_driver to invoke this code before the unbind callback.
To fix this, move the synchronize_irq() emulation code to dummy_pullup
so that it runs before unbind. Also, add a comment explaining why it is
necessary to have it there.
Reported-by: syzbot+eb4674092e6cc8d9e0bd@syzkaller.appspotmail.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210419033713.3021-1-mail@anirudhrb.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's remove path calls cancel_delayed_work(). However, that
function does not wait until the work function finishes. This means
that the callback function may still be running after the driver's
remove function has finished, which would result in a use-after-free.
Fix by calling cancel_delayed_work_sync(), which ensures that
the work is properly cancelled, no longer running, and unable
to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210407092947.3271507-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the virtual port_dev device is passed to DMA API, and this is
wrong because the device passed to DMA API calls must be the actual
hardware device performing the DMA.
The patch replaces usb_gadget_map_request/usb_gadget_unmap_request APIs
with usb_gadget_map_request_by_dev/usb_gadget_unmap_request_by_dev APIs
so the DMA capable platform device can be passed to the DMA APIs.
The patch fixes below backtrace detected on Facebook AST2500 OpenBMC
platforms:
[<80106550>] show_stack+0x20/0x24
[<80106868>] dump_stack+0x28/0x30
[<80823540>] __warn+0xfc/0x110
[<8011ac30>] warn_slowpath_fmt+0xb0/0xc0
[<8011ad44>] dma_map_page_attrs+0x24c/0x314
[<8016a27c>] usb_gadget_map_request_by_dev+0x100/0x1e4
[<805cedd8>] usb_gadget_map_request+0x1c/0x20
[<805cefbc>] ast_vhub_epn_queue+0xa0/0x1d8
[<7f02f710>] usb_ep_queue+0x48/0xc4
[<805cd3e8>] ecm_do_notify+0xf8/0x248
[<7f145920>] ecm_set_alt+0xc8/0x1d0
[<7f145c34>] composite_setup+0x680/0x1d30
[<7f00deb8>] ast_vhub_ep0_handle_setup+0xa4/0x1bc
[<7f02ee94>] ast_vhub_dev_irq+0x58/0x84
[<7f0309e0>] ast_vhub_irq+0xb0/0x1c8
[<7f02e118>] __handle_irq_event_percpu+0x50/0x19c
[<8015e5bc>] handle_irq_event_percpu+0x38/0x8c
[<8015e758>] handle_irq_event+0x38/0x4c
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Link: https://lore.kernel.org/r/20210331045831.28700-1-rentao.bupt@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a 75 Byte request, it would send the first 64 separately, then detect
that the remaining 11 Byte fit into a single DMA, but due to this bug set
the length to the original 75 Bytes. This leads to a DMA failure (which is
ignored...) and the request completes without the remaining bytes having
been sent.
Fixes: b84a8dee23 ("usb: gadget: add Faraday fotg210_udc driver")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/20210324141115.9384-2-fabian@ritter-vogt.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a121 completely.
While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.
Fixes: d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
Fixes: 9903b6bedd ("usb: gadget: pch-udc: fix lock")
Fixes: 1d23d16a88 ("usb: gadget: pch_udc: reorder spin_[un]lock to avoid deadlock")
Cc: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have a separate routine for VBUS sense, the interrupt may occur
before gadget driver is present. Hence, ->setup() call may oops the kernel:
[ 55.245843] BUG: kernel NULL pointer dereference, address: 00000010
...
[ 55.245843] EIP: pch_udc_isr.cold+0x162/0x33f
...
[ 55.245843] <IRQ>
[ 55.245843] ? pch_udc_svc_data_out+0x160/0x160
Check if driver is present before calling ->setup().
Fixes: f646cf9452 ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Either way ~0 will be in the correct byte order, hence
replace cpu_to_le32() by lower_32_bits(). Moreover,
it makes sparse happy, otherwise it complains:
.../pch_udc.c:1813:27: warning: incorrect type in assignment (different base types)
.../pch_udc.c:1813:27: expected unsigned int [usertype] dataptr
.../pch_udc.c:1813:27: got restricted __le32 [usertype]
Fixes: f646cf9452 ("USB device driver of Topcliff PCH")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210323153626.54908-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
init_dma_pools() calls dma_pool_create(...dev->dev) to create dma pool.
however, dev->dev is actually set after calling init_dma_pools(), which
effectively makes dma_pool_create(..NULL) and cause crash.
To fix this issue, init dma only after dev->dev is set.
[ 1.317993] RIP: 0010:dma_pool_create+0x83/0x290
[ 1.323257] Call Trace:
[ 1.323390] ? pci_write_config_word+0x27/0x30
[ 1.323626] init_dma_pools+0x41/0x1a0 [snps_udc_core]
[ 1.323899] udc_pci_probe+0x202/0x2b1 [amd5536udc_pci]
Fixes: 7c51247a1f (usb: gadget: udc: Provide correct arguments for 'dma_pool_create')
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20210317230400.357756-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull Kbuild updates from Masahiro Yamada:
- Fix false-positive build warnings for ARCH=ia64 builds
- Optimize dictionary size for module compression with xz
- Check the compiler and linker versions in Kconfig
- Fix misuse of extra-y
- Support DWARF v5 debug info
- Clamp SUBLEVEL to 255 because stable releases 4.4.x and 4.9.x
exceeded the limit
- Add generic syscall{tbl,hdr}.sh for cleanups across arches
- Minor cleanups of genksyms
- Minor cleanups of Kconfig
* tag 'kbuild-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (38 commits)
initramfs: Remove redundant dependency of RD_ZSTD on BLK_DEV_INITRD
kbuild: remove deprecated 'always' and 'hostprogs-y/m'
kbuild: parse C= and M= before changing the working directory
kbuild: reuse this-makefile to define abs_srctree
kconfig: unify rule of config, menuconfig, nconfig, gconfig, xconfig
kconfig: omit --oldaskconfig option for 'make config'
kconfig: fix 'invalid option' for help option
kconfig: remove dead code in conf_askvalue()
kconfig: clean up nested if-conditionals in check_conf()
kconfig: Remove duplicate call to sym_get_string_value()
Makefile: Remove # characters from compiler string
Makefile: reuse CC_VERSION_TEXT
kbuild: check the minimum linker version in Kconfig
kbuild: remove ld-version macro
scripts: add generic syscallhdr.sh
scripts: add generic syscalltbl.sh
arch: syscalls: remove $(srctree)/ prefix from syscall tables
arch: syscalls: add missing FORCE and fix 'targets' to make if_changed work
gen_compile_commands: prune some directories
kbuild: simplify access to the kernel's version
...
Instead of storing the version in a single integer and having various
kernel (and userspace) code how it's constructed, export individual
(major, patchlevel, sublevel) components and simplify kernel code that
uses it.
This should also make it easier on userspace.
Signed-off-by: Sasha Levin <sashal@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
