1) MOXA_ASPP_MON_EXT is broken at least since commit ecbbfd44a0 (TTY:
move tty buffers to tty_port) in 2012.
2) The ioctl definitions were never exposed to userspace, so noone should
actually be reliably using them.
3) They're not even mentioned in any of the mxser utilities.
So remove all these mxser-special ioctls: MOXA_ASPP_MON,
MOXA_ASPP_MON_EXT, and MOXA_SDS_RSTICOUNTER.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-25-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) The semantics are defined exactly nowhere.
2) The ioctl definition was never exposed to userspace, so noone should
actually be reliably using this.
3) It's not even mentioned in any of the mxser utilities.
Provided the above, remove this mxser-special ioctl.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-24-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In struct mxser_port, all the UART registers and masks, and the xon/xoff
character are stored into int. Let's re-type all these as UART registers
are 8bit (u8) and xon/xoff character is an unsigned char (cc_t in
ktermios).
This save some bytes in memory, but more importantly the change makes it
what it really is.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-19-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the new handling of receive chars (using the MUST chip
enhancements) into a separate function. This eliminates the need for the
intr_old label and makes the code of mxser_receive_chars more compact.
In the next step, we will extract the old handling too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mxser_interrupt is a bit confusing as it passes a pointer to LSR
variable ("status") to mxser_receive_chars. That function can indeed
update the LCR variable. Make this clear by not passing a variable by
reference, instead, return updated status. And change its type
accordingly -- to u8.
Note that the next patches will rework ISR so that even the definition
of status will be u8 soon too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-13-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Gpci_uart_info structure contains up to tripled information and
chose weird types for the members. Deduplicate the members and choose
proper types for the data -- everything can be u8 except baud rate.
There, we use speed_t, which is used in this context.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mxser.h serves only mxser.c, integrate the definitions into .c and
drop .h. There are some "semi-public" ioctl definitions, but they are
mostly go away in the next patches. If something, they would need to
live in an uapi header anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While mxser PCI cards are still around and produced (Moxa provided me
with two recently), ISA cards are obsolete for a long time. I haven't
seen anyone using the cards and the ISA code paths are barely tested.
Hence, remove ISA support from mxser driver so that we can clean the
driver up.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210618061516.662-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adjust the kconfig a little to allow disabling NO_IOMEM in UML. To
make an "allyesconfig" with CONFIG_NO_IOMEM=n build, adjust a few
Kconfig things elsewhere and add dummy asm/fb.h and asm/vga.h files.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Handle custom baud rates requested in the UPF_MAGIC_MULTIPLIER range
with BOTHER. Currently matching is exact, that is if a baud rate that
is not either of clk/4 or clk/8 is requested, then we fall through to
the default case, which will just divide the clock rate by 16 times the
rate requested, round it to closest integer, and possibly yield even
worse results then if clamping to the extra baud rates was chosen.
So for example if we have the usual base rate of 115200 and request a
rate of 230399, then the fall-through divisor calculation will yield 1,
and consequently the baud rate of 115200 will be programmed even though
obviously the magic rate of 230400 would be more appropriate.
Make the selection of the magic rates range-qualified then and use clk/4
for rates from clk/6 up (assuming `serial8250_get_baud_rate' has already
rejected any rates too far beyond clk/4), and otherwise use clk/8 for
rates from clk/12 up, and finally fall through to the standard divisor
calculation. Explicitly void using the undocumented rate of 153600bps
and stick to documented divisor values only.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105200232090.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit
2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>.
Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them. This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.
Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set. Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.
References:
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Table 31 - "Baud Rates", p. 77
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105190412280.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Contrary to what SMSC documentation says and unlike NS16C550A UARTs the
SMSC Super I/O IC claims compatibility with the SMSC UART implementation
does not support dividing the internal PLL clock by any divisor from 1
to 65535[1], with the exception of two magic divisors of 32769 and 32770
used respectively to select the high-speed data rates of 460800bps and
230400bps[2] if enabled on a port-by-port basis in with the Serial Port
Mode Register in the Device Configuration Space[3][4].
Instead empirical evidence indicates that the divisor, as stored in the
DLL and DLM register pair, has the range of 1 to 32767 only, and bit 7
of the DLM register (bit 15 of the divisor) effectively serves as a
selection bit for the prescaler from the base frequency of 7.3728MHz,
either 4 if the bit is 0, or 1 if the bit is 1 and high-speed operation
has been enabled with the Serial Port Mode Register.
So if high-speed operation has not been enabled, then say the values of
1 and 32769 (0x8001) written into the combined DLL and DLM register pair
both select the divisor of 1 and the baud rate of 115200bps.
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Section "Programmable Baud Rate Generator (and Divisor
Latches DLH, DLL)", p. 75
[2] same, Table 31 - "Baud Rates", p. 77
[3] same, Table 60 - "Serial Port 1, Logical Device 4 [Logical Device
Number = 0x04]", p. 153
[4] same, Table 61 - "Serial Port 2, Logical Device 5 [Logical Device
Number = 0x05]", p. 153
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106092330530.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor PCIe (Tornado) serial port devices are driven by a
fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
In the enhanced (650) mode, which we select in `autoconfig_has_efr' by
setting the ECB bit in the EFR register, and in the absence of clock
reconfiguration, which we currently don't do, the clock rate is divided
only by the oversampling rate of 16 as it is supplied to the baud rate
generator, yielding the baud base of 3906250. This comes from the reset
values of the TCR and MCR[7] registers which are both zero[1][2][3][4],
choosing the oversampling rate of 16 and the normal (divide by 1) baud
rate generator prescaler respectively. This is the rate that is divided
by the value held in the divisor latch to determine the baud rate used.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then.
References:
[1] "OXPCIe200 PCI Express Multi-Port Bridge", Oxford Semiconductor,
Inc., DS-0045, 10 Nov 2008, Section "Reset Configuration", p. 72
[2] "OXPCIe952 PCI Express Bridge to Dual Serial & Parallel Port",
Oxford Semiconductor, Inc., DS-0046, Mar 06 08, Section "Reset
Configuration", p. 27
[3] "OXPCIe954 PCI Express Bridge to Quad Serial Port", Oxford
Semiconductor, Inc., DS-0047, Feb 08, Section "Reset Configuration",
p. 28
[4] "OXPCIe958 PCI Express Bridge to Octal Serial Port", Oxford
Semiconductor, Inc., DS-0048, Feb 08, Section "Reset Configuration",
p. 28
Fixes: 7106b4e333 ("8250: Oxford Semiconductor Devices")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106100203510.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor PCIe (Tornado) serial port devices have their baud
base set incorrectly, however their `pciserial_board' entries have been
reused for Titan serial port devices. Define own entries for the latter
devices then, carrying over the settings, so that Oxford entries can be
fixed.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106100142310.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's a bit illogical to take magic constants in AUART_LINECTRL_WLEN.
Like in auart_console_get_options(), 2 means 7 bits. Switch
AUART_LINECTRL_WLEN to accept bit length, i.e. let it subtract 5 from
the parameter before doing the logic.
This will ease conversion from CSIZE to bits in mxs_auart_settermios()
in the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many tty drivers contain code to compute bits count depending on termios
cflags. So extract this code from serial core to two separate tty helper
functions:
* tty_get_char_size -- only size of a character, without flags,
* tty_get_frame_size -- complete size of a frame including flags.
In the next patch, calls to these new functions replace many copies of
this code.
Note that we accept only cflag as a parameter. That's because some
callers like pch_uart_startup or sunsab_console_setup don't have at hand
termios which we could pass around.
Cc: Joe Perches <joe@perches.com>
Cc: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
message is possible output when system enters suspend and while
transferring data, because clearing TIE bit in SCSCR is not able to
stop any dmaengine transfer.
sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
Note that this driver has already used some #ifdef in the .c file
so that this patch also uses #ifdef to fix the issue. Otherwise,
build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210610110806.277932-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_ldisc.c:63: warning: Excess function
parameter 'disc' description in 'tty_register_ldisc'
drivers/tty/tty_ldisc.c:90: warning: Function parameter or
member 'ldisc' not described in 'tty_unregister_ldisc'
drivers/tty/tty_ldisc.c:90: warning: Excess function
parameter 'disc' description in 'tty_unregister_ldisc'
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Link: https://lore.kernel.org/r/20210608024843.2756746-1-libaokun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the hack to assign the global console_port variable at probe time.
This assumption that cons->index is -1 is wrong for systems that specify
'console=' in the cmdline (or 'stdout-path' in dts). Hence, on such system
the actual console assignment is ignored, and the first UART that happens
to be probed is used as console instead.
Move the logic to console_setup() and map the console to the correct port
through the array of available ports instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20210528133321.1859346-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
