When an SPI device is unregistered, the spi->controller->cleanup() is
called in the device's release callback. That's wrong for a couple of
reasons:
1. spi_dev_put() can be called before spi_add_device() is called. And
it's spi_add_device() that calls spi_setup(). This will cause clean()
to get called without the spi device ever being setup.
2. There's no guarantee that the controller's driver would be present by
the time the spi device's release function gets called.
3. It also causes "sleeping in atomic context" stack dump[1] when device
link deletion code does a put_device() on the spi device.
Fix these issues by simply moving the cleanup from the device release
callback to the actual spi_unregister_device() function.
[1] - https://lore.kernel.org/lkml/CAHp75Vc=FCGcUyS0v6fnxme2YJ+qD+Y-hQDQLa2JhWNON9VmsQ@mail.gmail.com/
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210426235638.1285530-1-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull CFI on arm64 support from Kees Cook:
"This builds on last cycle's LTO work, and allows the arm64 kernels to
be built with Clang's Control Flow Integrity feature. This feature has
happily lived in Android kernels for almost 3 years[1], so I'm excited
to have it ready for upstream.
The wide diffstat is mainly due to the treewide fixing of mismatched
list_sort prototypes. Other things in core kernel are to address
various CFI corner cases. The largest code portion is the CFI runtime
implementation itself (which will be shared by all architectures
implementing support for CFI). The arm64 pieces are Acked by arm64
maintainers rather than coming through the arm64 tree since carrying
this tree over there was going to be awkward.
CFI support for x86 is still under development, but is pretty close.
There are a handful of corner cases on x86 that need some improvements
to Clang and objtool, but otherwise works well.
Summary:
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)"
* tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm64: allow CONFIG_CFI_CLANG to be selected
KVM: arm64: Disable CFI for nVHE
arm64: ftrace: use function_nocfi for ftrace_call
arm64: add __nocfi to __apply_alternatives
arm64: add __nocfi to functions that jump to a physical address
arm64: use function_nocfi with __pa_symbol
arm64: implement function_nocfi
psci: use function_nocfi for cpu_resume
lkdtm: use function_nocfi
treewide: Change list_sort to use const pointers
bpf: disable CFI in dispatcher functions
kallsyms: strip ThinLTO hashes from static functions
kthread: use WARN_ON_FUNCTION_MISMATCH
workqueue: use WARN_ON_FUNCTION_MISMATCH
module: ensure __cfi_check alignment
mm: add generic function_nocfi macro
cfi: add __cficanonical
add support for Clang CFI
Pull spi updates from Mark Brown:
"The only core work for SPI this time around is the completion of the
conversion to the new style method for specifying transfer delays,
meaning we can cope with what most controllers support more directly
using conversions in the core rather than open coding in drivers.
Otherwise it's a good stack of cleanups and fixes plus a few new
drivers.
Summary:
- Completion of the conversion to new style transfer delay
configuration
- Introduction and use of module_parport_driver() helper, merged here
as there's no parport tree
- Support for Altera SoCs on DFL buses, NXP i.MX8DL, HiSilicon
Kunpeng, MediaTek MT8195"
* tag 'spi-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (113 commits)
spi: Rename enable1 to activate in spi_set_cs()
spi: Convert Freescale QSPI binding to json schema
spi: stm32-qspi: fix debug format string
spi: tools: make a symbolic link to the header file spi.h
spi: fsi: add a missing of_node_put
spi: Make error handling of gpiod_count() call cleaner
spidev: Add Micron SPI NOR Authenta device compatible
spi: brcm,spi-bcm-qspi: convert to the json-schema
spi: altera: Add DFL bus driver for Altera API Controller
spi: altera: separate core code from platform code
spi: stm32-qspi: Fix compilation warning in ARM64
spi: Handle SPI device setup callback failure.
spi: sync up initial chipselect state
spi: stm32-qspi: Add dirmap support
spi: stm32-qspi: Trigger DMA only if more than 4 bytes to transfer
spi: stm32-qspi: fix pm_runtime usage_count counter
spi: spi-zynqmp-gqspi: return -ENOMEM if dma_map_single fails
spi: spi-zynqmp-gqspi: fix use-after-free in zynqmp_qspi_exec_op
spi: spi-zynqmp-gqspi: Resolved slab-out-of-bounds bug
spi: spi-zynqmp-gqspi: fix hang issue when suspend/resume
...
Printing size_t needs a special %zx format modifier to avoid a
warning like:
drivers/spi/spi-stm32-qspi.c:481:41: note: format string is defined here
481 | dev_dbg(qspi->dev, "%s len = 0x%x offs = 0x%llx buf = 0x%p\n", __func__, len, offs, buf);
Patrice already tried to fix this, but picked %lx instead of %zx,
which fixed some architectures but broke others in the same way.
Using %zx works everywhere.
Fixes: 18674dee3c ("spi: stm32-qspi: Add dirmap support")
Fixes: 1b8a7d4282 ("spi: stm32-qspi: Fix compilation warning in ARM64")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210422134955.1988316-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Each time we call spi_get_gpio_descs() the num_chipselect is overwritten
either by new value or by the old one. This is an extra operation in case
gpiod_count() returns an error. Besides that it slashes the error handling
of gpiod_count().
Refactor the code to make error handling of gpiod_count() call cleaner.
Note, that gpiod_count() never returns 0, take this into account as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210420164040.40055-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 7d93aecdb5 ("spi: Add generic support for unused native cs
with cs-gpios") excludes the valid case for the controllers that doesn't
need to switch native CS in order to perform the transfer, i.e. when
0 native
... ...
<n> - 1 native
<n> GPIO
<n> + 1 GPIO
... ...
where <n> defines maximum of native CSs supported by the controller.
To allow this, bail out from spi_get_gpio_descs() conditionally for
the controllers which explicitly marked with SPI_MASTER_GPIO_SS.
Fixes: 7d93aecdb5 ("spi: Add generic support for unused native cs with cs-gpios")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210420164425.40287-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the SPI core doesn't set the struct device fwnode pointer
when it creates a new SPI device. This means when the device is
registered the fwnode is NULL and the check in device_add which sets
the fwnode->dev pointer is skipped. This wasn't previously an issue,
however these two patches:
commit 4731210c09 ("gpiolib: Bind gpio_device to a driver to enable
fw_devlink=on by default")
commit ced2af4195 ("gpiolib: Don't probe gpio_device if it's not the
primary device")
Added some code to the GPIO core which relies on using that
fwnode->dev pointer to determine if a driver is bound to the fwnode
and if not bind a stub GPIO driver. This means the GPIO providers
behind SPI will get both the expected driver and this stub driver
causing the stub driver to fail if it attempts to request any pin
configuration. For example on my system:
madera-pinctrl madera-pinctrl: pin gpio5 already requested by madera-pinctrl; cannot claim for gpiochip3
madera-pinctrl madera-pinctrl: pin-4 (gpiochip3) status -22
madera-pinctrl madera-pinctrl: could not request pin 4 (gpio5) from group aif1 on device madera-pinctrl
gpio_stub_drv gpiochip3: Error applying setting, reverse things back
gpio_stub_drv: probe of gpiochip3 failed with error -22
The firmware node on the device created by the GPIO framework is set
through the of_node pointer hence things generally actually work,
however that fwnode->dev is never set, as the check was skipped at
device_add time. This fix appears to match how the I2C subsystem
handles the same situation.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210421101402.8468-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When initially probing the SPI slave device, the call for disabling an
SPI device without the SPI_CS_HIGH flag is not applied, as the
condition for checking whether or not the state to be applied equals the
one currently set evaluates to true.
This however might not necessarily be the case, as the chipselect might
be active.
Add a force flag to spi_set_cs which allows to override this
early exit condition. Set it to false everywhere except when called
from spi_setup to sync up the initial CS state.
Fixes commit d40f0b6f2e ("spi: Avoid setting the chip select if we don't
need to")
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20210416195956.121811-1-mail@david-bauer.net
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to optimize accesses to spi flashes, trigger a DMA only
if more than 4 bytes has to be transferred.
DMA transfer preparation's cost becomes negligible above 4 bytes to
transfer. Below this threshold, indirect transfer give more throughput.
mtd_speedtest shows that page write throughtput increases :
- from 779 to 853 KiB/s (~9.5%) with s25fl512s SPI-NOR.
- from 5283 to 5666 KiB/s (~7.25%) with Micron SPI-NAND.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210419121541.11617-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi controller supports 44-bit address space on AXI in DMA mode,
so set dma_addr_t width to 44-bit to avoid using a swiotlb mapping.
In addition, if dma_map_single fails, it should return immediately
instead of continuing doing the DMA operation which bases on invalid
address.
This fixes the following crash which occurs in reading a big block
from flash:
[ 123.633577] zynqmp-qspi ff0f0000.spi: swiotlb buffer is full (sz: 4194304 bytes), total 32768 (slots), used 0 (slots)
[ 123.644230] zynqmp-qspi ff0f0000.spi: ERR:rxdma:memory not mapped
[ 123.784625] Unable to handle kernel paging request at virtual address 00000000003fffc0
[ 123.792536] Mem abort info:
[ 123.795313] ESR = 0x96000145
[ 123.798351] EC = 0x25: DABT (current EL), IL = 32 bits
[ 123.803655] SET = 0, FnV = 0
[ 123.806693] EA = 0, S1PTW = 0
[ 123.809818] Data abort info:
[ 123.812683] ISV = 0, ISS = 0x00000145
[ 123.816503] CM = 1, WnR = 1
[ 123.819455] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000805047000
[ 123.825887] [00000000003fffc0] pgd=0000000803b45003, p4d=0000000803b45003, pud=0000000000000000
[ 123.834586] Internal error: Oops: 96000145 [#1] PREEMPT SMP
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-6-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After calling platform_set_drvdata(pdev, xqspi) in probe, the return
value of dev_get_drvdata(dev) is a pointer to struct zynqmp_qspi but
not struct spi_controller. A wrong structure type passing to the
functions spi_controller_suspend/resume will hang the system.
And we should check the return value of spi_controller_suspend, if
an error is returned, return it to PM subsystem to stop suspend.
Also, GQSPI_EN_MASK should be written to GQSPI_EN_OFST to enable
the spi controller in zynqmp_qspi_resume since it was disabled in
zynqmp_qspi_suspend before.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-3-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The clks "pclk" and "ref_clk" are enabled twice during the probe. The
first time is in the function zynqmp_qspi_probe and the second time is
in zynqmp_qspi_setup_op which is called by devm_spi_register_controller.
Then calling zynqmp_qspi_remove (rmmod this module) to disable these clks
will trigger a warning as below:
[ 309.124604] Unpreparing enabled qspi_ref
[ 309.128641] WARNING: CPU: 1 PID: 537 at drivers/clk/clk.c:824 clk_core_unprepare+0x108/0x110
Since pm_runtime works now, clks can be enabled/disabled by calling
zynqmp_runtime_suspend/resume. So we don't need to enable these clks
explicitly in zynqmp_qspi_setup_op. Remove them to fix this issue.
And remove clk enabling/disabling in zynqmp_qspi_resume because there is
no spi transfer operation so enabling ref_clk is redundant meanwhile pclk
is not disabled for it is shared with other peripherals.
Furthermore replace clk_enable/disable with clk_prepare_enable and
clk_disable_unprepare in runtime_suspend/resume functions.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-2-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series fix a potential interrupt race condition and
cleanup the ACPI protection for the driver.
Change since v1:
- reword the commit in patch #2
Link: https://lore.kernel.org/linux-spi/1617881505-51552-1-git-send-email-yangyicong@hisilicon.com/
Yicong Yang (2):
spi: hisi-sfc-v3xx: fix potential irq race condition
spi: hisi-sfc-v3xx: drop unnecessary ACPI_PTR and related ifendif
protection
drivers/spi/spi-hisi-sfc-v3xx.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
--
2.8.1
We use ACPI_PTR() and related ifendif protection for the id table.
This is unnecessary as the struct acpi_device_id is defined in
mod_devicetable.h and doesn't rely on ACPI. The driver doesn't
use any ACPI apis, so it can be compiled in the ACPI=n case
with no warnings.
So remove the ACPI_PTR and related ifendif protection, also
replace the header acpi.h with mod_devicetable.h.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1618228708-37949-3-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull OPP (Operating Performance Points) framework updates for v5.13
from Viresh Kumar:
"This adds devm variants for OPP APIs and updates few of the users
as well (Yangtao Li and Dmitry Osipenko)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
memory: samsung: exynos5422-dmc: Convert to use resource-managed OPP API
drm/panfrost: Convert to use resource-managed OPP API
drm/lima: Convert to use resource-managed OPP API
mmc: sdhci-msm: Convert to use resource-managed OPP API
spi: spi-qcom-qspi: Convert to use resource-managed OPP API
spi: spi-geni-qcom: Convert to use resource-managed OPP API
serial: qcom_geni_serial: Convert to use resource-managed OPP API
opp: Change return type of devm_pm_opp_attach_genpd()
opp: Change return type of devm_pm_opp_register_set_opp_helper()
opp: Add devres wrapper for dev_pm_opp_of_add_table
opp: Add devres wrapper for dev_pm_opp_set_supported_hw
opp: Add devres wrapper for dev_pm_opp_set_regulators
opp: Add devres wrapper for dev_pm_opp_set_clkname
Quanyang Wang <quanyang.wang@windriver.com>:
From: Quanyang Wang <quanyang.wang@windriver.com>
Hello,
This series fix some issues that occurs when the gqspi driver switches to spi-mem framework.
Hi Amit,
I rewrite the "Subject" and "commit message" of these patches, so they
look different from the ones which you reviewed before. I still keep
your "Reviewed-by" and hope you will not mind.
Regards,
Quanyang Wang
Quanyang Wang (4):
spi: spi-zynqmp-gqspi: use wait_for_completion_timeout to make
zynqmp_qspi_exec_op not interruptible
spi: spi-zynqmp-gqspi: add mutex locking for exec_op
spi: spi-zynqmp-gqspi: transmit dummy circles by using the
controller's internal functionality
spi: spi-zynqmp-gqspi: fix incorrect operating mode in
zynqmp_qspi_read_op
drivers/spi/spi-zynqmp-gqspi.c | 53 +++++++++++++++++-----------------
1 file changed, 27 insertions(+), 26 deletions(-)
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
If device_get_match_data returns NULL, devdata isn't being updated
properly. It is being used later in the function. Both devdata and
spi->devdata should be updated to avoid NULL pointer dereference.
Addresses-Coverity: ("NULL pointer dereference")
Fixes: 0e6521f13c ("spi: orion: Use device_get_match_data() helper")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Link: https://lore.kernel.org/r/20210408195718.GA3075166@LEGION
Signed-off-by: Mark Brown <broonie@kernel.org>
When some drivers use spi to send data, spi_transfer->speed_hz is
not assigned. If spidev->max_speed_hz is not assigned as well, it
will cause an error in configuring the clock.
Add a check for these two values before configuring the clock. An
error will be returned when they are not assigned.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20210408103347.244313-2-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When starting a read operation, we should call zynqmp_qspi_setuprxdma
first to set xqspi->mode according to xqspi->bytes_to_receive and
to calculate correct xqspi->dma_rx_bytes. Then in the function
zynqmp_qspi_fillgenfifo, generate the appropriate command with
operating mode and bytes to transfer, and fill the GENFIFO with
the command to perform the read operation.
Calling zynqmp_qspi_fillgenfifo before zynqmp_qspi_setuprxdma will
result in incorrect transfer length and operating mode. So change
the calling order to fix this issue.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-5-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
