This patch adds driver for Cadence's XSPI controller.
It supports 3 work modes.
1. ACMD (auto command) work mode
ACMD name is because it uses auto command engine in the controller.
It further has 2 modes PIO and CDMA (command DMA).
The CDMA work mode is dedicated for high-performance application
where very low software overhead is required. In this mode the
Command Engine is programmed by the series of linked descriptors
stored in system memory. These descriptors provide commands to execute
and store status information for finished commands.
The PIO mode work mode is dedicated for single operation where
constructing a linked list of descriptors would require too
much effort.
2. STIG (Software Triggered Instruction Generator) work mode
In STIG mode, controller sends low-level instructions to memory.
Each instruction is 128-bit width. There is special instruction
DataSequence which carries information about data phase.
Driver uses Slave DMA interface to transfer data as only this
interface can be used in STIG work mode.
3. Direct work mode
This work mode allows sending data without invoking any command through
the slave interface.
Currently only STIG work mode is enabled, remaining work modes will
be added later.
Signed-off-by: Konrad Kociolek <konrad@cadence.com>
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1632038734-23999-1-git-send-email-pthombar@cadence.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding an id_table listing the
SPI IDs for everything.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210923170023.1683-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull spi modalias fix from Mark Brown:
"Fix modalias issues
As reported by Russell King the change to use OF style modaliases for
DT enumerated broke at least the spi-nor driver, the patch here
reverts that change to fix the regression.
Sadly this will mean that anything that started loading since the
change to OF modaliases will run into issues, there doesn't seem to be
any approach which doesn't cause some problems and thi seems like the
least bad approach - gory details are in the commit log for the
change.
I'm currently working through the SPI drivers to add ID tables and
missing IDs to tables which should address things from the other end,
this seems more straightforward and robust than any other options"
* tag 'spi-fix-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Revert modalias changes
Currently for SPI devices we use the spi_device_id for module autoloading
even on systems using device tree, meaning that listing a compatible string
in the of_match_table isn't enough to have the module for a SPI driver
autoloaded.
We attempted to fix this by generating OF based modaliases for devices
instantiated from DT in 3ce6c9e261 ("spi: add of_device_uevent_modalias
support") but this meant we no longer reported spi_device_id based aliases
which broke drivers such as spi-nor which don't list all the compatible
strings they support directly for DT, and in at least that case it's not
super practical to do so given the very large number of compatibles
needed, much larger than the number spi_device_ids due to vendor strings.
As a result fell back to using spi_device_id based modalises.
Try to close the gap by printing a warning when a SPI driver has a DT
compatible that won't be matched as a SPI device ID with the goal of having
drivers provide both. Given fallback compatibles this check is going to be
excessive but it should be robust which is probably more important here.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210921192149.50740-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
During the v5.13 cycle we updated the SPI subsystem to generate OF style
modaliases for SPI devices, replacing the old Linux style modalises we
used to generate based on spi_device_id which are the DT style name with
the vendor removed. Unfortunately this means that we start only
reporting OF style modalises and not the old ones and there is nothing
that ensures that drivers list every possible OF compatible string in
their OF ID table. The result is that there are systems which have been
relying on loading modules based on the old style that are now broken,
as found by Russell King with spi-nor on Macchiatobin.
spi-nor is a particularly problematic case for this, it only lists a
single generic DT compatible jedec,spi-nor in the driver but supports a
huge raft of device specific compatibles, with a large set of part
numbers many of which are offered by multiple vendors. Russell's
searches of upstream device trees has turned up examples with vendor
names written in non-standard ways too. To make matters worse up until
8ff16cf77c ("Documentation: devicetree: m25p80: add "nor-jedec"
binding") the generic compatible was not part of the binding so there
are device trees out there written to that binding version which don't
list it all. The sheer number of parts supported together with our
previous approach of ignoring the vendor ID makes robustly fixing this
by adding compatibles to the spi-nor driver seem problematic, the
current DT binding document does not list all the parts supported by the
driver at the minute (further patches will fix this).
I've also investigated supporting both formats of modalias
simultaneously but that doesn't seem possible, especially without
breaking our userspace ABI which is obviously not viable.
Instead revert the relevant changes for now:
e09f2ab8ee ("spi: update modalias_show after of_device_uevent_modalias support")
3ce6c9e261 ("spi: add of_device_uevent_modalias support")
This will unfortunately mean that any system which had started having
modules autoload based on the OF compatibles for drivers that list
things there but not in the spi_device_ids will now not have those
modules load which is itself a regression. Since it affects a narrower
time window and the particularly problematic spi-nor driver may be
critical to system boot on smaller systems this seems the best of a
series of bad options. I will start an audit of SPI drivers to identify
and fix cases where things won't autoload using spi_device_id, this is
not great but seems to be the best way forward that anyone has been able
to identify.
Thanks to Russell for both his report and the additional diagnostic and
analysis work he has done here, the detailed research above was his
work.
Fixes: e09f2ab8ee ("spi: update modalias_show after of_device_uevent_modalias support")
Fixes: 3ce6c9e261 ("spi: add of_device_uevent_modalias support")
Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Cc: Andreas Schwab <schwab@suse.de>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Pull spi fixes from Mark BrownL
"This contains a couple of fixes, one fix for handling of zero length
transfers on Rockchip devices and a warning fix which will conflict
with a version you did but cleans up some extra unneeded forward
declarations as well which seems a bit neater"
* tag 'spi-fix-v5.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: tegra20-slink: Declare runtime suspend and resume functions conditionally
spi: rockchip: handle zero length transfers without timing out
Without CONFIG_PM enabled, the SET_RUNTIME_PM_OPS() macro ends up being
empty, and the only use of tegra_slink_runtime_{resume,suspend} goes
away, resulting in
drivers/spi/spi-tegra20-slink.c:1200:12: error: ‘tegra_slink_runtime_resume’ defined but not used [-Werror=unused-function]
1200 | static int tegra_slink_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/spi-tegra20-slink.c:1188:12: error: ‘tegra_slink_runtime_suspend’ defined but not used [-Werror=unused-function]
1188 | static int tegra_slink_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
mark the functions __maybe_unused to make the build happy.
This hits the alpha allmodconfig build (and others).
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hi,
This patchset introduces support for SPI controllers found in the
Ingenic JZ47xx family of SoCs. Of particular note, this allows to
replace GPIO backed SPI on the MIPS Creator CI20 board.
Mark:
Checkpatch generates a `need consistent spacing around '*'` error on
this patchset, however I believe this is a false positive due to it
confusing a pointer with multiplication operator inside a macro.
Rob:
I refrained from adding SPI pin groups into the bindings, as I felt that
would be enforcing a policy (SPI signals can be multiplexed on multiple
pin groups on the board, per use case). Instead, I included an example
pin configuration into the relevant commit description.
Other controllers already present in ci20.dts do specify their pin
groups, but I think this is bad practice. Do you have particular
guidelines on this?
Pavel:
Feel free to add your Tested-by, if you still have your CI20 setup
around :) I tested this driver with two SPI mode MMC/SD card readers and
also with the spi-loopback test driver.
Cheers,
Artur
Artur Rojek (2):
SPI: add Ingenic JZ47xx driver.
MIPS: JZ4780: CI20: DTS: add SPI controller config
Paul Cercueil (1):
dt-bindings: spi: Document Ingenic SPI controller bindings
.../devicetree/bindings/spi/ingenic,spi.yaml | 72 +++
arch/mips/boot/dts/ingenic/ci20.dts | 9 +-
arch/mips/boot/dts/ingenic/jz4780.dtsi | 44 +-
drivers/spi/Kconfig | 9 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-ingenic.c | 482 ++++++++++++++++++
6 files changed, 602 insertions(+), 15 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/ingenic,spi.yaml
create mode 100644 drivers/spi/spi-ingenic.c
--
2.33.0
The following build error is seen with CONFIG_PM=n.
drivers/spi/spi-tegra20-slink.c:1188:12: error:
'tegra_slink_runtime_suspend' defined but not used
drivers/spi/spi-tegra20-slink.c:1200:12: error:
'tegra_slink_runtime_resume' defined but not used
Declare the functions only if PM is enabled. While at it, remove the
unnecessary forward declarations.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210907045358.2138282-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously zero length transfers submitted to the Rokchip SPI driver would
time out in the SPI layer. This happens because the SPI peripheral does
not trigger a transfer completion interrupt for zero length transfers.
Fix that by completing zero length transfers immediately at start of
transfer.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20210827050357.165409-1-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull ARM SoC driver updates from Arnd Bergmann:
"These are updates for drivers that are tied to a particular SoC,
including the correspondig device tree bindings:
- A couple of reset controller changes for unisoc, uniphier, renesas
and zte platforms
- memory controller driver fixes for omap and tegra
- Rockchip io domain driver updates
- Lots of updates for qualcomm platforms, mostly touching their
firmware and power management drivers
- Tegra FUSE and firmware driver updateѕ
- Support for virtio transports in the SCMI firmware framework
- cleanup of ixp4xx drivers, towards enabling multiplatform support
and bringing it up to date with modern platforms
- Minor updates for keystone, mediatek, omap, renesas"
* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
reset: simple: remove ZTE details in Kconfig help
soc: rockchip: io-domain: Remove unneeded semicolon
soc: rockchip: io-domain: add rk3568 support
dt-bindings: power: add rk3568-pmu-io-domain support
bus: ixp4xx: return on error in ixp4xx_exp_probe()
soc: renesas: Prefer memcpy() over strcpy()
firmware: tegra: Stop using seq_get_buf()
soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
soc/tegra: fuse: Add runtime PM support
soc/tegra: fuse: Clear fuse->clk on driver probe failure
soc/tegra: pmc: Prevent racing with cpuilde driver
soc/tegra: bpmp: Remove unused including <linux/version.h>
dt-bindings: soc: ti: pruss: Add dma-coherent property
soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
firmware: arm_scmi: Use WARN_ON() to check configured transports
firmware: arm_scmi: Fix boolconv.cocci warnings
soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
soc: mediatek: mmsys: add MT8365 support
...
Pull driver core updates from Greg KH:
"Here is the big set of driver core patches for 5.15-rc1.
These do change a number of different things across different
subsystems, and because of that, there were 2 stable tags created that
might have already come into your tree from different pulls that did
the following
- changed the bus remove callback to return void
- sysfs iomem_get_mapping rework
Other than those two things, there's only a few small things in here:
- kernfs performance improvements for huge numbers of sysfs users at
once
- tiny api cleanups
- other minor changes
All of these have been in linux-next for a while with no reported
problems, other than the before-mentioned merge issue"
* tag 'driver-core-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (33 commits)
MAINTAINERS: Add dri-devel for component.[hc]
driver core: platform: Remove platform_device_add_properties()
ARM: tegra: paz00: Handle device properties with software node API
bitmap: extend comment to bitmap_print_bitmask/list_to_buf
drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI
topology: use bin_attribute to break the size limitation of cpumap ABI
lib: test_bitmap: add bitmap_print_bitmask/list_to_buf test cases
cpumask: introduce cpumap_print_list/bitmask_to_buf to support large bitmask and list
sysfs: Rename struct bin_attribute member to f_mapping
sysfs: Invoke iomem_get_mapping() from the sysfs open callback
debugfs: Return error during {full/open}_proxy_open() on rmmod
zorro: Drop useless (and hardly used) .driver member in struct zorro_dev
zorro: Simplify remove callback
sh: superhyway: Simplify check in remove callback
nubus: Simplify check in remove callback
nubus: Make struct nubus_driver::remove return void
kernfs: dont call d_splice_alias() under kernfs node lock
kernfs: use i_lock to protect concurrent inode updates
kernfs: switch kernfs to use an rwsem
kernfs: use VFS negative dentry caching
...
Pull char / misc driver updates from Greg KH:
"Here is the big set of char/misc driver changes for 5.15-rc1.
Lots of different driver subsystems are being updated in here,
notably:
- mhi subsystem update
- fpga subsystem update
- coresight/hwtracing subsystem update
- interconnect subsystem update
- nvmem subsystem update
- parport drivers update
- phy subsystem update
- soundwire subsystem update
and there are some other char/misc drivers being updated as well:
- binder driver additions
- new misc drivers
- lkdtm driver updates
- mei driver updates
- sram driver updates
- other minor driver updates.
Note, there are no habanalabs driver updates in this pull request,
that will probably come later before -rc1 is out in a different
request.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (169 commits)
Revert "bus: mhi: Add inbound buffers allocation flag"
misc/pvpanic: fix set driver data
VMCI: fix NULL pointer dereference when unmapping queue pair
char: mware: fix returnvar.cocci warnings
parport: remove non-zero check on count
soundwire: cadence: do not extend reset delay
soundwire: intel: conditionally exit clock stop mode on system suspend
soundwire: intel: skip suspend/resume/wake when link was not started
soundwire: intel: fix potential race condition during power down
phy: qcom-qmp: Add support for SM6115 UFS phy
dt-bindings: phy: qcom,qmp: Add SM6115 UFS PHY bindings
phy: qmp: Provide unique clock names for DP clocks
lkdtm: remove IDE_CORE_CP crashpoint
lkdtm: replace SCSI_DISPATCH_CMD with SCSI_QUEUE_RQ
coresight: Replace deprecated CPU-hotplug functions.
Documentation: coresight: Add documentation for CoreSight config
coresight: syscfg: Add initial configfs support
coresight: config: Add preloaded configurations
coresight: etm4x: Add complex configuration handlers to etmv4
coresight: etm-perf: Update to activate selected configuration
...
The function wait_for_completion_interruptible_timeout will return
-ERESTARTSYS immediately when receiving SIGKILL signal which is sent
by "jffs2_gcd_mtd" during umounting jffs2. This will break the SPI memory
operation because the data transmitting may begin before the command or
address transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
Fixes: 67dca5e580 ("spi: spi-mem: Add support for Zynq QSPI controller")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210826005930.20572-1-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently there are two places where the error return variable ret is
being assigned -ETIMEDOUT on timeout errors and this value is not
being returned. Fix this by returning -ETIMEDOUT rather than redundantly
assiging it to ret.
Addresses-Coverity: ("Unused value")
Fixes: 0b89fc0a36 ("spi: rockchip-sfc: add rockchip serial flash controller")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210818141051.36320-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When clearing the chip-select mask, the controller will switch to chip
selecting the native CS0 line. Because the control register chip-select
mask is not updated in a single write this will cause undesirable
chip-selection of CS0 even when requesting to select other native
chip-select lines. This is additionally problematic as the chip-select
may still be asserted. With the ARMADA 38x SoC the controller will
assert both the desired native chip-select and CS0.
To avoid any undesirable behaviour with the chip-select lines, update
the control register with a single write. This avoids selecting CS0 and
causes the (de-)assert to apply at the same time.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Link: https://lore.kernel.org/r/20210816050228.3223661-1-nathan@nathanrossi.com
Signed-off-by: Mark Brown <broonie@kernel.org>
i.MX eCSPI errata handling for 5.15:
It includes all required changes for handling i.MX6/7 eCSPI errata
ERR009165, which causes FIFO transfer to be sent twice in DMA mode.
Both SPI and DMA maintainers agree to merge it through arm-soc tree.
* tag 'imx-ecspi-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dmaengine: imx-sdma: add terminated list for freed descriptor in worker
dmaengine: imx-sdma: add uart rom script
dma: imx-sdma: add i.mx6ul compatible name
dmaengine: imx-sdma: remove ERR009165 on i.mx6ul
spi: imx: remove ERR009165 workaround on i.mx6ul
spi: imx: fix ERR009165
dmaengine: imx-sdma: add mcu_2_ecspi script
dmaengine: dma: imx-sdma: add fw_loaded and is_ram_script
dmaengine: imx-sdma: remove duplicated sdma_load_context
Revert "dmaengine: imx-sdma: refine to load context only once"
Revert "ARM: dts: imx6: Use correct SDMA script for SPI cores"
Revert "ARM: dts: imx6q: Use correct SDMA script for SPI5 core"
Link: https://lore.kernel.org/r/20210809071838.GF30984@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix the following waring:
drivers/spi/spi-mxic.c: In function ‘mxic_spi_mem_exec_op’:
drivers/spi/spi-mxic.c:401:3: warning: this ‘if’ clause does not guard... [-Wmisleading-indentation]
if (op->data.dir == SPI_MEM_DATA_IN)
^~
drivers/spi/spi-mxic.c:403:4: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
if (op->data.dtr)
^~
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Zhengxun Li <zhengxunli@mxic.com.tw>
Link: https://lore.kernel.org/r/20210810142405.2221540-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For spi-pic32, this is probably not currently an issue but is still good to
fix though.
Fixes: 1bcb9f8ceb ("spi: spi-pic32: Add PIC32 SPI master driver")
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210810081727.19491-2-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Tegra SPI driver supports runtime PM, which controls the clock
enable state, but the clk is also enabled separately from the RPM
at the driver probe time, and thus, stays always on. Fix it.
Runtime PM now is always available on Tegra, hence there is no need to
check the RPM presence in the driver anymore. Remove these checks.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210731192731.5869-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We need the fixes in here as well, and resolves some merge issues with
the mhi codebase.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
