Remove extra le32_to_cpu() conversion, data is already converted from
le32 to cpu endianness. This fixes two following warnings:
drivers/soc/qcom/socinfo.c:322:36: sparse: sparse: cast to restricted __le32
drivers/soc/qcom/socinfo.c:323:36: sparse: sparse: cast to restricted __le32
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 734c78e7fe ("soc: qcom: socinfo: add info from PMIC models array")
Link: https://lore.kernel.org/r/20210118152236.514776-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Requests sent to RPMH can be sent as fire-n-forget or response required,
with the latter ensuring the command has been completed by the hardware
accelerator. Commands in a request with tcs_cmd::wait set, would ensure
that those select commands are sent as response required, even though
the actual TCS request may be fire-n-forget.
Also, commands with .wait flag were also guaranteed to be complete
before the following command in the TCS is sent. This means that the
next command of the same request blocked until the current request is
completed. This could mean waiting for a voltage to settle or series of
NOCs be configured before the next command is sent. But drivers using
this feature have never cared about the serialization aspect. By not
enforcing the serialization we can allow the hardware to run in parallel
improving the performance.
Let's clarify the usage of this member in the tcs_cmd structure to mean
only completion and not serialization. This should also improve the
performance of bus requests where changes could happen in parallel.
Also, CPU resume from deep idle may see benefits from certain wake
requests.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1610008770-13891-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When triggering a TCS to send its contents, reading back the trigger
value may return an incorrect value. That is because, writing the
trigger may raise an interrupt which could be handled immediately and
the trigger value could be reset in the interrupt handler.
A write_tcs_reg_sync() would read back the value that is written and try
to match it to the value written to ensure that the value is written,
but if that value is different, we may see false error for same.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1606211610-15168-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
clang static analysis reports this problem
pdr_interface.c:596:6: warning: Branch condition evaluates
to a garbage value
if (!req.service_path[0])
^~~~~~~~~~~~~~~~~~~~
This check that req.service_path was set in an earlier loop.
However req is a stack variable and its initial value
is undefined.
So initialize req to 0.
Fixes: fbe639b44a ("soc: qcom: Introduce Protection Domain Restart helpers")
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20200819184637.15648-1-trix@redhat.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fixes the following W=1 kernel build warning(s):
drivers/soc/qcom/wcnss_ctrl.c:81: warning: Function parameter or member 'major' not described in 'wcnss_version_resp'
drivers/soc/qcom/wcnss_ctrl.c:81: warning: Function parameter or member 'minor' not described in 'wcnss_version_resp'
drivers/soc/qcom/wcnss_ctrl.c:81: warning: Function parameter or member 'version' not described in 'wcnss_version_resp'
drivers/soc/qcom/wcnss_ctrl.c:81: warning: Function parameter or member 'revision' not described in 'wcnss_version_resp'
drivers/soc/qcom/wcnss_ctrl.c:122: warning: Function parameter or member 'rpdev' not described in 'wcnss_ctrl_smd_callback'
drivers/soc/qcom/wcnss_ctrl.c:122: warning: Function parameter or member 'priv' not described in 'wcnss_ctrl_smd_callback'
drivers/soc/qcom/wcnss_ctrl.c:122: warning: Function parameter or member 'addr' not described in 'wcnss_ctrl_smd_callback'
drivers/soc/qcom/wcnss_ctrl.c:122: warning: Excess function parameter 'channel' description in 'wcnss_ctrl_smd_callback'
drivers/soc/qcom/wcnss_ctrl.c:272: warning: Function parameter or member 'priv' not described in 'qcom_wcnss_open_channel'
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201103152838.1290217-19-lee.jones@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
RPMH and drivers that use RPMH APIs need Command DB API to find the
dynamic resource information. Let's match the RPMH to match the Command
DB configuration.
This should fix undefined symbol references reported by CI :
aarch64-linux-ld: drivers/clk/qcom/clk-rpmh.o: in function `clk_rpmh_probe':
>> clk-rpmh.c:(.text+0xac): undefined reference to `cmd_db_read_addr'
>> aarch64-linux-ld: clk-rpmh.c:(.text+0xc0): undefined reference to `cmd_db_read_aux_data'
aarch64-linux-ld: drivers/soc/qcom/rpmh-rsc.o: in function `rpmh_rsc_probe':
>> rpmh-rsc.c:(.text+0x42c): undefined reference to `cmd_db_ready'
aarch64-linux-ld: drivers/regulator/qcom-rpmh-regulator.o: in function `rpmh_regulator_probe':
>> qcom-rpmh-regulator.c:(.text+0x3e0): undefined reference to `cmd_db_read_addr'
Cc: Todd Kjos <tkjos@google.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Link: https://lore.kernel.org/r/20201008040907.7036-1-ilina@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The functions geni_se_select_fifo_mode() and
geni_se_select_fifo_mode() are a little funny. They read/write a
bunch of memory mapped registers even if they don't change or aren't
relevant for the current protocol. Let's make them a little more
sane. We'll also add a comment explaining why we don't do some of the
operations for UART.
NOTE: there is no evidence at all that this makes any performance
difference and it fixes no bugs. However, it seems (to me) like it
makes the functions a little easier to understand. Decreasing the
amount of times we read/write memory mapped registers is also nice,
even if we are using "relaxed" variants.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201013142448.v2.3.I646736d3969dc47de8daceb379c6ba85993de9f4@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On geni-i2c transfers using DMA, it was seen that if you program the
command (I2C_READ) before calling geni_se_rx_dma_prep() that it could
cause interrupts to fire. If we get unlucky, these interrupts can
just keep firing (and not be handled) blocking further progress and
hanging the system.
In commit 02b9aec592 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
we avoided that by making sure we didn't program the command until
after geni_se_rx_dma_prep() was called. While that avoided the
problems, it also turns out to be invalid. At least in the TX case we
started seeing sporadic corrupted transfers. This is easily seen by
adding an msleep() between the DMA prep and the writing of the
command, which makes the problem worse. That means we need to revert
that commit and find another way to fix the bogus IRQs.
Specifically, after reverting commit 02b9aec592 ("i2c:
i2c-qcom-geni: Fix DMA transfer race"), I put some traces in. I found
that the when the interrupts were firing like crazy:
- "m_stat" had bits for M_RX_IRQ_EN, M_RX_FIFO_WATERMARK_EN set.
- "dma" was set.
Further debugging showed that I could make the problem happen more
reliably by adding an "msleep(1)" any time after geni_se_setup_m_cmd()
ran up until geni_se_rx_dma_prep() programmed the length.
A rather simple fix is to change geni_se_select_dma_mode() so it's a
true inverse of geni_se_select_fifo_mode() and disables all the FIFO
related interrupts. Now the problematic interrupts can't fire and we
can program things in the correct order without worrying.
As part of this, let's also change the writel_relaxed() in the prepare
function to a writel() so that our DMA is guaranteed to be prepared
now that we can't rely on geni_se_setup_m_cmd()'s writel().
NOTE: the only current user of GENI_SE_DMA in mainline is i2c.
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Fixes: 02b9aec592 ("i2c: i2c-qcom-geni: Fix DMA transfer race")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20201013142448.v2.1.Ifdb1b69fa3367b81118e16e9e4e63299980ca798@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Older SoCs like MSM8916, MSM8939, MSM8974, MSM8996, ...
use "voltage corners" instead of "voltage levels".
It seems like they all use exactly the same set of corner values,
a value from 0-6 where 6 is the maximum corner (super turbo).
In preparation to add the power domains for MSM8916, rename
MAX_8996_RPMPD_STATE to MAX_CORNER_RPMPD_STATE to make it clear
that this is the max_state to be used for all SoCs using corners. -
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200916104135.25085-2-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit efde2659b0 ("drivers: qcom: rpmh-rsc: Use rcuidle tracepoints
for rpmh") was written to fix a bug seen in an unmerged series that
implemented a struct generic_pm_domain::power_off() callback calling
rpmh_flush(). See stack trace below.
Call trace:
dump_backtrace+0x0/0x174
show_stack+0x20/0x2c
dump_stack+0xc8/0x124
lockdep_rcu_suspicious+0xe4/0x104
__tcs_buffer_write+0x230/0x2d0
rpmh_rsc_write_ctrl_data+0x210/0x270
rpmh_flush+0x84/0x24c
rpmh_domain_power_off+0x78/0x98
_genpd_power_off+0x40/0xc0
genpd_power_off+0x168/0x208
Later the final merged solution is to use CPU PM notification to invoke
rpmh_flush() and power_off() callback of genpd is not implemented in the
driver.
CPU PM notifiers are run with RCU enabled/watching (see cpu_pm_notify()
and how it calls rcu_irq_enter_irqson() before calling the notifiers).
Remove this change since RCU will not be idle during CPU PM notifications
hence not required to use _rcuidle tracepoint. Using _rcuidle tracepoint
prevented rpmh driver to be loadable module as these are not exported
symbols.
This reverts commit efde2659b0.
Cc: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1601877596-32676-2-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Older chipsets may not be allowed to configure certain LLCC registers
as that is handled by the secure side software. However, this is not
the case for newer chipsets and they must configure these registers
according to the contents of the SCT table, while keeping in mind that
older targets may not have these capabilities. So add support to allow
such configuration of registers to enable capacity based allocation
and power collapse retention for capable chipsets.
Reason for choosing capacity based allocation rather than the default
way based allocation is because capacity based allocation allows more
finer grain partition and provides more flexibility in configuration.
As for the retention through power collapse, it has an advantage where
the cache hits are more when we wake up from power collapse although
it does burn more power but the exact power numbers are not known at
the moment.
Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
[saiprakash.ranjan@codeaurora.org: use existing config and reword commit msg]
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/dac7e11cf654fc6d75a6b5ca062ab87b01547810.1600151951.git.saiprakash.ranjan@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
smp2p_update_bits() should disable interrupts when it acquires its
spinlock. This is important because without the _irqsave, a priority
inversion can occur.
This function is called both with interrupts enabled in
qcom_q6v5_request_stop(), and with interrupts disabled in
ipa_smp2p_panic_notifier(). IRQ handling of spinlocks should be
consistent to avoid the panic notifier deadlocking because it's
sitting on the thread that's already got the lock via _request_stop().
Found via lockdep.
Cc: stable@vger.kernel.org
Fixes: 50e9964141 ("soc: qcom: smp2p: Qualcomm Shared Memory Point to Point")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Link: https://lore.kernel.org/r/20200929133040.RESEND.1.Ideabf6dcdfc577cf39ce3d95b0e4aa1ac8b38f0c@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
