Not all RPM firmware versions have the dynamic sleep stats offset
available. Most older versions use a fixed offset of 0xdba0.
Add support for this using new SoC-specific compatibles for APQ8084,
MSM8226, MSM8916 and MSM8974.
Even older SoCs seem to use a different offset and stats format.
If needed those could be supported in the future by adding separate
compatibles for those with a different stats_config.
Cc: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211119213953.31970-3-stephan@gerhold.net
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
ARM_QCOM_SPM_CPUIDLE can be selected when compile-testing on
other architectures, but this causes a Kconfig warning
for QCOM_SPM:
WARNING: unmet direct dependencies detected for QCOM_SPM
Depends on [n]: ARCH_QCOM [=n]
Selected by [y]:
- ARM_QCOM_SPM_CPUIDLE [=y] && CPU_IDLE [=y] && (ARM [=y] || ARM64) && (ARCH_QCOM [=n] || COMPILE_TEST [=y]) && !ARM64 && MMU [=y]
Make it possible to also compile-test this one, which can
be done now that v5.15-rc5 lets you select QCOM_SCM everywhere.
Fixes: a871be6b8e ("cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver")
Fixes: 498ba2a8a2 ("cpuidle: Fix ARM_QCOM_SPM_CPUIDLE configuration")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix following coccicheck warning:
./drivers/soc/qcom/apr.c:485:1-23: WARNING: Function
for_each_child_of_node should have of_node_put() before return
Early exits from for_each_child_of_node should decrement the
node reference counter.
Fixes: 8347356626 ("soc: qcom: apr: Add avs/audio tracking functionality")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211014083017.19714-1-wanjiabing@vivo.com
This patch adds feature negotiation and ssr ack feature between
local host and remote processor. Local host can negotiate on common
features supported with remote processor.
When ssr ack feature bit is set, the remote processor will tell local
host when it is reinitialized. All clients registered for falling edge
interrupts will be notified when the smp2p entries are cleared for ssr.
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Deepak Kumar Singh <deesin@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1633450403-21281-1-git-send-email-deesin@codeaurora.org
Let's add a driver to read the stats from remote processor and
export to debugfs.
The driver creates "qcom_sleep_stats" directory in debugfs and
adds files for various low power mode available. Below is sample
output with command
cat /sys/kernel/debug/qcom_sleep_stats/ddr
count = 0
Last Entered At = 0
Last Exited At = 0
Accumulated Duration = 0
Signed-off-by: Mahesh Sivasubramanian <msivasub@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
[mkshah: add subsystem sleep stats, create one file for each stat]
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1634107104-22197-3-git-send-email-mkshah@codeaurora.org
The general expectation is that powering on a power-domain should make
the power domain deliver some power, and if a specific performance state
is needed further requests has to be made.
But in contrast with other power-domain implementations (e.g. rpmpd) the
RPMh does not have an interface to enable the power, so the driver has
to vote for a particular corner (performance level) in rpmh_power_on().
But the corner is never initialized, so a typical request to simply
enable the power domain would not actually turn on the hardware. Further
more, when no more clients vote for a performance state (i.e. the
aggregated vote is 0) the power domain would be turned off.
Fix both of these issues by always voting for a corner with non-zero
value, when the power domain is enabled.
The tracking of the lowest non-zero corner is performed to handle the
corner case if there's ever a domain with a non-zero lowest corner, in
which case both rpmh_power_on() and rpmh_rpmhpd_set_performance_state()
would be allowed to use this lowest corner.
Fixes: 279b7e8a62 ("soc: qcom: rpmhpd: Add RPMh power domain driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211005033732.2284447-1-bjorn.andersson@linaro.org
Practically all modern Qualcomm platforms has a single reserved-memory
region for SMEM. So rather than having to describe SMEM in the form of a
node with a reference to a reserved-memory node, allow the SMEM device
to be instantiated directly from the reserved-memory node.
The current means of falling back to dereferencing the "memory-region"
is kept as a fallback, if it's determined that the SMEM node is a
reserved-memory node.
The "qcom,smem" compatible is added to the reserved_mem_matches list, to
allow the reserved-memory device to be probed.
In order to retain the readability of the code, the resolution of
resources is split from the actual ioremapping.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20210930182111.57353-4-bjorn.andersson@linaro.org
Qualcomm Generic Packet router aka GPR is the IPC mechanism found
in AudioReach next generation signal processing framework to perform
command and response messages between various processors.
GPR has concepts of static and dynamic port, all static services like
APM (Audio Processing Manager), PRM (Proxy resource manager) have
fixed port numbers where as dynamic services like graphs have dynamic
port numbers which are allocated at runtime. All GPR packet messages
will have source and destination domain and port along with opcode
and payload.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210927135559.738-6-srinivas.kandagatla@linaro.org
APR and other packet routers like GPR are pretty much same and
interact with other drivers in similar way.
Ex: GPR ports can be considered as APR services, only difference
is they are allocated dynamically.
Other difference is packet layout, which should not matter
with the apis abstracted. Apart from this the rest of the
functionality is pretty much identical across APR and GPR.
Make the apr code more reusable by abstracting it service level,
rather than device level so that we do not need to write
new drivers for other new packet routers like GPR.
This patch is in preparation to add GPR support to this driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210927135559.738-4-srinivas.kandagatla@linaro.org
Remote susbsystems notify fatal crash through smp2p interrupt.
When remoteproc crashes it can cause soc to come out of low power
state and may not allow again to enter in low power state until
crash is handled.
Mark smp2p interrupt wakeup capable so that interrupt handler is
executed and remoteproc crash can be handled in system resume path.
This patch marks interrupt wakeup capable but keeps wakeup disabled
by default. User space can enable it based on its requirement for
wakeup from suspend.
Signed-off-by: Deepak Kumar Singh <deesin@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1632220467-27410-1-git-send-email-deesin@codeaurora.org
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. The safe replacement is strscpy().
This is a previous step in the path to remove the strcpy() function
entirely from the kernel.
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210808125012.4715-2-len.baker@gmx.com
