Add support for the io_uring interface in I/O-polled mode.
This feature is disabled in the driver by default. To enable the feature, a
module parameter "poll_queues" has to be set with the desired number of
polling queues.
When the feature is enabled, the driver reserves a certain number of
operational queue pairs for the poll_queues either from the available queue
pairs or creates additional queue pairs based on the operational queue
availability.
The Polling queues will have corresponding IRQ and ISR functions as similar
to default queues. However, the IRQ line is disabled by the driver for
poll_queues.
Link: https://lore.kernel.org/r/20211220141159.16117-22-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The IOC sends a Prepare for Reset Event to the host to prepare for a Soft
Reset. This event data has two reason codes:
1. Start - The host is expected to gracefully quiesce all I/O within
approximately 1 second.
2. Abort - The IOC is requesting to abort a previous Prepare for Reset
Event request. Normal I/O may be resumed.
Link: https://lore.kernel.org/r/20211220141159.16117-20-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detect asynchronous reset that occurred in the firmware by polling for
reset history bit of IOC status register is set and if that bit is set,
then the driver waits for the controller to become ready and then
re-initializes the controller.
Also reduce the time driver is waiting for the controller to acknowledge
the reset action after issuing a specific reset action to the
controller. The wait time is reduced from 510 seconds to 30 seconds. If the
controller didn't acknowledge a specific reset action within the time
interval then the driver marks the controller as unrecoverable instead of
retrying two more times prior to giving up.
Link: https://lore.kernel.org/r/20211220141159.16117-17-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver marks the controller as unrecoverable if there is an
asynchronous reset or fault during the initialization, reinitialization
post reset, and OS resume.
Enhance driver to retry the initialization, re-initialization, and resume
sequences for a maximum of 3 times if the controller became faulty or
asynchronously reset due to a firmware activation during the initialization
sequence.
Link: https://lore.kernel.org/r/20211220141159.16117-15-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The following special handling is needed for UNMAP commands issued to NVMe
drives:
- On B0 boards, if the parameter list length is greater than 24 and not a
16-byte multiple, then truncate the parameter list length to a 16-byte
multiple.
- On A0 boards, if the parameter list length is greater than block
descriptor data length + 8, then truncate the parameter list length to
block descriptor data length + 8 value.
Link: https://lore.kernel.org/r/20211220141159.16117-10-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SAS4 Controller firmware exposes the SES devices in Managed PCIe Switch
as a PCIe Device Type SCSI Device
(MPI3_DEVICE0_PCIE_DEVICE_INFO_TYPE_SCSI_DEVICE).
Driver is enhanced to handle this device type by:
- Exposing the device to the upper layers and
- Not updating any hardware sectors & virtual boundary settings as these
settings are needed only for NVMe devices.
Link: https://lore.kernel.org/r/20211220141159.16117-7-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, smartpqi, lpfc,
target, megaraid_sas, hisi_sas, qla2xxx) and minor updates and bug
fixes.
Notable core changes are the removal of scsi->tag which caused some
churn in obsolete drivers and a sweep through all drivers to call
scsi_done() directly instead of scsi->done() which removes a pointer
indirection from the hot path and a move to register core sysfs files
earlier, which means they're available to KOBJ_ADD processing, which
necessitates switching all drivers to using attribute groups"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: lpfc: Update lpfc version to 14.0.0.3
scsi: lpfc: Allow fabric node recovery if recovery is in progress before devloss
scsi: lpfc: Fix link down processing to address NULL pointer dereference
scsi: lpfc: Allow PLOGI retry if previous PLOGI was aborted
scsi: lpfc: Fix use-after-free in lpfc_unreg_rpi() routine
scsi: lpfc: Correct sysfs reporting of loop support after SFP status change
scsi: lpfc: Wait for successful restart of SLI3 adapter during host sg_reset
scsi: lpfc: Revert LOG_TRACE_EVENT back to LOG_INIT prior to driver_resource_setup()
scsi: ufs: ufshcd-pltfrm: Fix memory leak due to probe defer
scsi: ufs: mediatek: Avoid sched_clock() misuse
scsi: mpt3sas: Make mpt3sas_dev_attrs static
scsi: scsi_transport_sas: Add 22.5 Gbps link rate definitions
scsi: target: core: Stop using bdevname()
scsi: aha1542: Use memcpy_{from,to}_bvec()
scsi: sr: Add error handling support for add_disk()
scsi: sd: Add error handling support for add_disk()
scsi: target: Perform ALUA group changes in one step
scsi: target: Replace lun_tg_pt_gp_lock with rcu in I/O path
scsi: target: Fix alua_tg_pt_gps_count tracking
scsi: target: Fix ordered tag handling
...
Include Hannes' SCSI command result rework in the staging branch.
[mkp: remove DRIVER_SENSE from mpi3mr]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Detection of firmware fault or any kind of unresponsiveness in the
controller (any admin command which times out) results in resetting the
controller. The primary reset mechanisms used are either soft reset or diag
fault reset. A reset is performed if the host sets the ResetAction field in
the HostDiagnostic register to either 001b (soft reset) or 007b (diag fault
reset). After successfully resetting the controller the driver
reinitializes the controller by going through start of the day
initialization procedure. Pending I/Os during the reset are returned back
to the SCSI midlayer for retry.
Link: https://lore.kernel.org/r/20210520152545.2710479-10-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.co
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create operational request and reply queue pair.
The MPI3 transport interface consists of an Administrative Request Queue,
an Administrative Reply Queue, and Operational Messaging Queues. The
Operational Messaging Queues are the primary communication mechanism
between the host and the I/O Controller (IOC). Request messages, allocated
in host memory, identify I/O operations to be performed by the IOC. These
operations are queued on an Operational Request Queue by the host driver.
Reply descriptors track I/O operations as they complete. The IOC queues
these completions in an Operational Reply Queue.
To fulfil large contiguous memory requirement, driver creates multiple
segments and provide the list of segments. Each segment size should be 4K
which is a hardware requirement. An element array is contiguous or
segmented. A contiguous element array is located in contiguous physical
memory. A contiguous element array must be aligned on an element size
boundary. An element's physical address within the array may be directly
calculated from the base address, the Producer/Consumer index, and the
element size.
Expected phased identifier bit is used to find out valid entry on reply
queue. Driver sets <ephase> bit and IOC inverts the value of this bit on
each pass.
Link: https://lore.kernel.org/r/20210520152545.2710479-4-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
