i.MX8ULP is a new SoC with Ultra low power support, it has a Cortex-M33
core and two Cortex-A35 cores. We need to add new configuration because
it could not reuse the previous i.MX7/8 configuration.
i.MX8ULP M33 core is kicked by ROM, it is not under control of A35 core.
So need to mark the method is IMX_RPROC_NONE.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210622060148.18411-3-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
mbox_send_message is called by passing a local dummy message or
a function parameter. As the message is queued, it is dereferenced.
This works because the message field is not used by the stm32 ipcc
driver, but it is not clean.
Fix by passing a constant string in all cases.
The associated comments are removed because rproc should not have to
deal with the behavior of the mailbox frame.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20210420091922.29429-1-arnaud.pouliquen@foss.st.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When cdev_add is called after device_add has been called there is no
way for the userspace to know about the addition of a cdev as cdev_add
itself doesn't trigger a uevent notification, or for the kernel to
know about the change to devt. This results in two problems:
- mknod is never called for the cdev and hence no cdev appears on
devtmpfs.
- sysfs links to the new cdev are not established.
The cdev needs to be added and devt assigned before device_add() is
called in order for the relevant sysfs and devtmpfs entries to be
created and the uevent to be properly populated.
Signed-off-by: Siddharth Gupta <sidgup@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1623723671-5517-2-git-send-email-sidgup@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 AM64x family of SoCs have a ICSSG IP that is similar to the
version on AM65x SR2.0 SoCs with some minor differences. The AM64x
SoCs contain two instances of this newer ICSSG IP. Each ICSSG processor
subsystem contains 2 primary PRU cores, 2 auxiliary PRU cores called
RTUs, and 2 new auxiliary cores called Transmit PRUs (Tx_PRUs).
Enhance the existing PRU remoteproc driver to support all these PRU,
RTU and Tx_PRU cores by using specific compatibles. The cores have the
same memory copying limitations as on AM65x, so reuses the custom memcpy
function within the driver's ELF loader implementation. The initial
names for the firmware images for each PRU core are retrieved from
DT nodes, and can be adjusted through sysfs if required.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210623173243.7862-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When CONFIG_IMX_REMOTEPROC is y and CONFIG_HAVE_ARM_SMCCC
is not set, compiling errors are encountered as follows:
drivers/remoteproc/imx_rproc.o: in function `imx_rproc_stop':
imx_rproc.c:(.text+0x140): undefined reference to `__arm_smccc_smc'
drivers/remoteproc/imx_rproc.o: in function `imx_rproc_detect_mode':
imx_rproc.c:(.text+0x272): undefined reference to `__arm_smccc_smc'
drivers/remoteproc/imx_rproc.o: in function `imx_rproc_start':
imx_rproc.c:(.text+0x5e0): undefined reference to `__arm_smccc_smc'
__arm_smccc_smc is defined when HAVE_ARM_SMCCC is y, so
add dependency on HAVE_ARM_SMCCC in IMX_REMOTEPROC configuration.
Fixes: 79806d32d5 ("remoteproc: imx_rproc: support i.MX8MN/P")
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20210610031530.26326-1-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A phys_addr_t may be wider than an int or pointer:
drivers/remoteproc/stm32_rproc.c: In function 'stm32_rproc_da_to_pa':
drivers/remoteproc/stm32_rproc.c:583:30: error: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'phys_addr_t' {aka 'long long unsigned int'} [-Werror=format=]
583 | dev_dbg(dev, "da %llx to pa %#x\n", da, *pa);
Print it by reference using the special %pap format string.
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Fixes: 8a471396d2 ("remoteproc: stm32: Move resource table setup to rproc_ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210421140053.3727528-1-arnd@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The K3 AM64x SoC family has a revised R5F sub-system and contains a
subset of the R5F clusters present on J721E SoCs. The K3 AM64x SoCs
only have two dual-core Arm R5F clusters/subsystems with 2 R5F cores
each present within the MAIN voltage domain (MAIN_R5FSS0 & MAIN_R5FSS1).
The revised IP has the following distinct features:
1. The R5FSS IP supports a new "Single-CPU" mode instead of the LockStep
mode on existing SoCs (AM65x, J721E or J7200). This mode is similar
to LockStep-mode on J7200 SoCs in terms of TCM usage without the
fault-tolerant safety feature provided by the LockStep mode.
The Core1 TCMs are combined with the Core0 TCMs effectively doubling
the amount of TCMs available in Single-CPU mode. The LockStep-mode
on previous AM65x and J721E SoCs could only use the Core0 TCMs. These
combined TCMs appear contiguous at the respective Core0 TCM addresses.
The code though is executed only on a single CPU (on Core0), and as
such, requires the halt signal to be programmed only for Core0, while
the resets need to be managed for both the cores.
2. TCMs are auto-initialized during module power-up, and the behavior
is programmable through a MMR bit. This feature is the same as on
the recent J7200 SoCs.
Extend the support to these clusters in the K3 R5F remoteproc driver
using AM64x specific compatibles. New TI-SCI flags and a unique cluster
mode are also needed for the cluster mode detection on these SoCs. The
reset assert and deassert sequence of both the cores in Single-CPU mode
is agnostic of the order, so the same LockStep reset and release sequences
are re-used.
The integration of these clusters is very much similar to existing SoCs
otherwise.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210327143117.1840-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pull remoteproc updates from Bjorn Andersson:
"This adds support to the remoteproc core for detaching Linux from a
running remoteproc, e.g. to reboot Linux while leaving the remoteproc
running, and it enable this support in the stm32 remoteproc driver.
It also introduces a property for memory carveouts to track if they
are iomem or system ram, to enable proper handling of the differences.
The imx_rproc received a number of fixes and improvements, in
particular support for attaching to already running remote processors
and i.MX8MQ and i.MX8MM support.
The Qualcomm wcss driver gained support for starting and stopping the
wireless subsystem on QCS404, when not using the TrustZone-based
validator/loader.
Finally it brings a few fixes to the TI PRU and to the firmware loader
for the Qualcomm modem subsystem drivers"
* tag 'rproc-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (53 commits)
remoteproc: stm32: add capability to detach
dt-bindings: remoteproc: stm32-rproc: add new mailbox channel for detach
remoteproc: imx_rproc: support remote cores booted before Linux Kernel
remoteproc: imx_rproc: move memory parsing to rproc_ops
remoteproc: imx_rproc: enlarge IMX7D_RPROC_MEM_MAX
remoteproc: imx_rproc: add missing of_node_put
remoteproc: imx_rproc: fix build error without CONFIG_MAILBOX
remoteproc: qcom: wcss: Remove unnecessary PTR_ERR()
remoteproc: qcom: wcss: Fix wrong pointer passed to PTR_ERR()
remoteproc: qcom: pas: Add modem support for SDX55
dt-bindings: remoteproc: qcom: pas: Add binding for SDX55
remoteproc: qcom: wcss: Fix return value check in q6v5_wcss_init_mmio()
remoteproc: pru: Fix and cleanup firmware interrupt mapping logic
remoteproc: pru: Fix wrong success return value for fw events
remoteproc: pru: Fixup interrupt-parent logic for fw events
remoteproc: qcom: wcnss: Allow specifying firmware-name
remoteproc: qcom: wcss: explicitly request exclusive reset control
remoteproc: qcom: wcss: Add non pas wcss Q6 support for QCS404
dt-bindings: remoteproc: qcom: Add Q6V5 Modem PIL binding for QCS404
remoteproc: qcom: wcss: populate hardcoded param using driver data
...
- When remote cores are kicked before Linux Kernel, we are not able
to get resource table from the firmware elf file, so we need to add
rsc_table to hold the resource table published by remote cores and
imx_rproc_get_loaded_rsc_table is to get the resource table.
- Per remoteproc framework, add attach hook for processor in a detached
state.
- Add imx_rproc_detect_mode to detect remote cores' working mode to
set the state which is required by remoteproc framework.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1617846289-13496-5-git-send-email-peng.fan@oss.nxp.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The PRU firmware interrupt mappings are configured and unconfigured in
.start() and .stop() callbacks respectively using the variables 'evt_count'
and a 'mapped_irq' pointer. These variables are modified only during these
callbacks but are not re-initialized/reset properly during unwind or
failure paths. These stale values caused a kernel crash while stopping a
PRU remoteproc running a different firmware with no events on a subsequent
run after a previous run that was running a firmware with events.
Fix this crash by ensuring that the evt_count is 0 and the mapped_irq
pointer is set to NULL in pru_dispose_irq_mapping(). Also, reset these
variables properly during any failures in the .start() callback. While
at this, the pru_dispose_irq_mapping() callsites are all made to look
the same, moving any conditional logic to inside the function.
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Fixes: c75c9fdac6 ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210407155641.5501-4-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The irq_create_fwspec_mapping() returns a proper virq value on success
and 0 upon any failure. The pru_handle_intrmap() treats this as an error
and disposes all firmware event mappings correctly, but is returning
this incorrect value as is, letting the pru_rproc_start() interpret it
as a success and boot the PRU.
Fix this by returning an error value back upon any such failure. While
at this, revise the error trace to print some meaningful info about the
failed event.
Fixes: c75c9fdac6 ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210407155641.5501-3-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The PRU firmware interrupt mapping logic in pru_handle_intrmap() uses
of_irq_find_parent() with PRU device node to get a handle to the PRUSS
Interrupt Controller at present. This logic however requires that the
PRU nodes always define a interrupt-parent property. This property is
neither a required/defined property as per the PRU remoteproc binding,
nor is relevant from a DT node point of view without any associated
interrupts. The current logic finds a wrong interrupt controller and
fails to perform proper mapping without any interrupt-parent property
in the PRU nodes.
Fix this logic to always find and use the sibling interrupt controller.
Also, while at this, fix the acquired interrupt controller device node
reference properly.
Fixes: c75c9fdac6 ("remoteproc: pru: Add support for PRU specific interrupt configuration")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20210407155641.5501-2-s-anna@ti.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When a remote processor that was attached to is stopped, special care
must be taken to make sure the shutdown process is similar to what
it would be had it been started by the remoteproc core.
This patch takes care of that by making a copy of the resource
table currently used by the remote processor. From that point on
the copy is used, as if the remote processor had been started by
the remoteproc core.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-13-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move the setting of the resource table installed by an external
entity to rproc_ops::get_loaded_rsc_table(). This is to support
scenarios where a remote processor has been attached to but is
detached at a later stage. To re-attach the remote processor,
the address of the resource table needs to be available
at a later time than the platform driver's probe() function.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Link: https://lore.kernel.org/r/20210312162453.1234145-7-mathieu.poirier@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
