Function tegra_pinctrl_gpio_request_enable() and
tegra_pinctrl_gpio_disable_free() uses pin offset instead
of group offset, causing the driver to use wrong offset
to enable gpio.
Add a helper function tegra_pinctrl_get_group() to parse the
pin group and determine correct offset.
Signed-off-by: Kartik K <kkartik@nvidia.com>
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Link: https://lore.kernel.org/r/20211025110959.27751-1-pshete@nvidia.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
spmi-mpp did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should be
usable from the start without the consumer having to make an additional
call to get the proper IRQ on the parent. This patch adds hierarchical
IRQ chip support to the spmi-mpp code to correct this issue.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-17-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process.
This change will also allow for the removal of the interrupts property
later in this patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,spmi-mpp OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-16-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ssbi-mpp did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should be
usable from the start without the consumer having to make an additional
call to get the proper IRQ on the parent. This patch adds hierarchical
IRQ chip support to the ssbi-mpp code to correct this issue.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-15-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process.
This change will also allow for the removal of the interrupts property
later in this patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,ssbi-mpp OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-14-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some systems such as the Microsoft Surface Laptop 4 leave interrupts
enabled and configured for use in sleep states on boot, which cause
unexpected behaviour such as spurious wakes and failed resumes in
s2idle states.
As interrupts should not be enabled until they are claimed and
explicitly enabled, disabling any interrupts mistakenly left enabled by
firmware should be safe.
Signed-off-by: Sachi King <nakato@nakato.io>
Link: https://lore.kernel.org/r/20211009033240.21543-1-nakato@nakato.io
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If some bits in a pin Pull-Up control register (PUPR) control pin
pull-down instead of pin pull-up, there are two pinmux_bias_reg entries:
a first one with the puen field filled in, listing pins with pull-up
functionality, and a second one with the pud field filled in, listing
pins with pull-down functionality. On encountering the second entry,
where puen is NULL, the for-loop terminates early, causing the remaining
bias registers not to be checked. In addition, sh_pfc_check_bias_reg()
does not handle such entries.
Fix this by treating pinmux_bias_reg.puen and pinmux_bias_reg.pud the
same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/29526d06fa223cffd785cdb264b756a202b11cea.1633615652.git.geert+renesas@glider.be
If some bits in a pin Pull-Up control register (PUPR) control pin
pull-down instead of pin pull-up, there are two pinmux_bias_reg entries:
a first one with the puen field filled in, listing pins with pull-up
functionality, and a second one with the pud field filled in, listing
pins with pull-down functionality. On encountering the second entry,
where puen is NULL, the for-loop terminates early, causing the remaining
bias registers not to be saved/restored during PSCI system suspend.
Fortunately this does not trigger on any supported system yet, as PSCI
is only used on R-Car Gen3 and RZ/G2 systems, which all have separate
pin Pull-Enable (PUEN) and pin Pull-Up/Down control (PUD) registers.
Avoid this ever becoming a problem by treating pinmux_bias_reg.puen and
pinmux_bias_reg.pud the same. Note that a register controlling both
pull-up and pull-down pins would be saved and restored twice, which is
harmless.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/59d2fbddff685b6a7a82ff17d2b37633e30e8860.1633615652.git.geert+renesas@glider.be
When resuming from low power, the driver attempts to restore the
configuration of some pins. This is done by a call to:
stm32_pinctrl_restore_gpio_regs(struct stm32_pinctrl *pctl, u32 pin)
where 'pin' must be a valid pin value (i.e. matching some 'groups->pin').
Fix the current implementation which uses some wrong 'pin' value.
Fixes: e2f3cf18c3 ("pinctrl: stm32: add suspend/resume management")
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Link: https://lore.kernel.org/r/20211008122517.617633-1-fabien.dessenne@foss.st.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit a49d784d5a.
The updated binding was wrong / invalid and has been reverted. There
isn't any upstream kernel DTS using it and Broadcom isn't known to use
it neither. There is close to zero chance this will cause regression for
anyone.
Actually in-kernel bcm5301x.dtsi still uses the old good binding and so
it's broken since the driver update. This revert fixes it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211008205938.29925-3-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull asm-generic fixes from Arnd Bergmann:
"There is one build fix for Arm platforms that ended up impacting most
architectures because of the way the drivers/firmware Kconfig file is
wired up:
The CONFIG_QCOM_SCM dependency have caused a number of randconfig
regressions over time, and some still remain in v5.15-rc4. The fix we
agreed on in the end is to make this symbol selected by any driver
using it, and then building it even for non-Arm platforms with
CONFIG_COMPILE_TEST.
To make this work on all architectures, the drivers/firmware/Kconfig
file needs to be included for all architectures to make the symbol
itself visible.
In a separate discussion, we found that a sound driver patch that is
pending for v5.16 needs the same change to include this Kconfig file,
so the easiest solution seems to have my Kconfig rework included in
v5.15.
Finally, the branch also includes a small unrelated build fix for
NOMMU architectures"
Link: https://lore.kernel.org/all/20210928153508.101208f8@canb.auug.org.au/
Link: https://lore.kernel.org/all/20210928075216.4193128-1-arnd@kernel.org/
Link: https://lore.kernel.org/all/20211007151010.333516-1-arnd@kernel.org/
* tag 'asm-generic-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: give stub iounmap() on !MMU same prototype as elsewhere
qcom_scm: hide Kconfig symbol
firmware: include drivers/firmware/Kconfig unconditionally
Now that SCM can be a loadable module, we have to add another
dependency to avoid link failures when ipa or adreno-gpu are
built-in:
aarch64-linux-ld: drivers/net/ipa/ipa_main.o: in function `ipa_probe':
ipa_main.c:(.text+0xfc4): undefined reference to `qcom_scm_is_available'
ld.lld: error: undefined symbol: qcom_scm_is_available
>>> referenced by adreno_gpu.c
>>> gpu/drm/msm/adreno/adreno_gpu.o:(adreno_zap_shader_load) in archive drivers/built-in.a
This can happen when CONFIG_ARCH_QCOM is disabled and we don't select
QCOM_MDT_LOADER, but some other module selects QCOM_SCM. Ideally we'd
use a similar dependency here to what we have for QCOM_RPROC_COMMON,
but that causes dependency loops from other things selecting QCOM_SCM.
This appears to be an endless problem, so try something different this
time:
- CONFIG_QCOM_SCM becomes a hidden symbol that nothing 'depends on'
but that is simply selected by all of its users
- All the stubs in include/linux/qcom_scm.h can go away
- arm-smccc.h needs to provide a stub for __arm_smccc_smc() to
allow compile-testing QCOM_SCM on all architectures.
- To avoid a circular dependency chain involving RESET_CONTROLLER
and PINCTRL_SUNXI, drop the 'select RESET_CONTROLLER' statement.
According to my testing this still builds fine, and the QCOM
platform selects this symbol already.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently, if the GPIO is configured as output in the bootloader
and user changes the mode to input in HLOS, it would end up
getting configured as input/output. Functionally, this is fine;
however, there may be some requirements where the output needs
to be disabled so that it can be used only for input.
Add support to enable/disable output mode through "output-enable"
or "output-disable" pinctrl properties.
Signed-off-by: Subbaraman Narayanamurthy <quic_subbaram@quicinc.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631588246-4811-3-git-send-email-quic_subbaram@quicinc.com
[Drop copyright change which is already upstrean in -rcN]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The separation of pinctrl and gpio drivers created a tiny window where
a pinconfig setting might produce a null-pointer dereference.
The affected device were rk3288-veyron devices in this case.
Pinctrl-hogs are claimed when the pinctrl driver is registered,
at which point their pinconfig settings will be applied.
At this time the now separate gpio devices will not have been created
yet and the matching driver won't have probed yet, making the gpio->foo()
call run into a null-ptr.
As probing is not really guaranteed to have been completed at a specific
time, introduce a queue that can hold the output settings until the gpio
driver has probed and will (in a separate patch) fetch the elements
of the list.
We expect the gpio driver to empty the list, but will nevertheless empty
it ourself on remove if that didn't happen.
Fixes: 9ce9a02039 ("pinctrl/rockchip: drop the gpio related codes")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210913224926.1260726-4-heiko@sntech.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pmic_gpio_child_to_parent_hwirq() and
gpiochip_populate_parent_fwspec_fourcell() translate a pinctrl-
spmi-gpio irqspec to an SPMI controller irqspec. When they do
this, they use a fixed SPMI slave ID of 0 and a fixed GPIO
peripheral offset of 0xC0 (corresponding to SPMI address 0xC000).
This translation results in an incorrect irqspec for secondary
PMICs that don't have a slave ID of 0 as well as for PMIC chips
which have GPIO peripherals located at a base address other than
0xC000.
Correct this issue by passing the slave ID of the pinctrl-spmi-
gpio device's parent in the SPMI controller irqspec and by
calculating the peripheral ID base from the device tree 'reg'
property of the pinctrl-spmi-gpio device.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Signed-off-by: satya priya <skakit@codeaurora.org>
Fixes: ca69e2d165 ("qcom: spmi-gpio: add support for hierarchical IRQ chip")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1631798498-10864-2-git-send-email-skakit@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
