If some bits in a pin Pull-Up control register (PUPR) control pin
pull-down instead of pin pull-up, there are two pinmux_bias_reg entries:
a first one with the puen field filled in, listing pins with pull-up
functionality, and a second one with the pud field filled in, listing
pins with pull-down functionality. On encountering the second entry,
where puen is NULL, the for-loop terminates early, causing the remaining
bias registers not to be checked. In addition, sh_pfc_check_bias_reg()
does not handle such entries.
Fix this by treating pinmux_bias_reg.puen and pinmux_bias_reg.pud the
same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/29526d06fa223cffd785cdb264b756a202b11cea.1633615652.git.geert+renesas@glider.be
If some bits in a pin Pull-Up control register (PUPR) control pin
pull-down instead of pin pull-up, there are two pinmux_bias_reg entries:
a first one with the puen field filled in, listing pins with pull-up
functionality, and a second one with the pud field filled in, listing
pins with pull-down functionality. On encountering the second entry,
where puen is NULL, the for-loop terminates early, causing the remaining
bias registers not to be saved/restored during PSCI system suspend.
Fortunately this does not trigger on any supported system yet, as PSCI
is only used on R-Car Gen3 and RZ/G2 systems, which all have separate
pin Pull-Enable (PUEN) and pin Pull-Up/Down control (PUD) registers.
Avoid this ever becoming a problem by treating pinmux_bias_reg.puen and
pinmux_bias_reg.pud the same. Note that a register controlling both
pull-up and pull-down pins would be saved and restored twice, which is
harmless.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/59d2fbddff685b6a7a82ff17d2b37633e30e8860.1633615652.git.geert+renesas@glider.be
As R-Car H3 ES1.x (R8A77950) and R-Car ES2.0+ (R8A77951) use the same
compatible value, the pin control driver relies on soc_device_match()
with soc_id = "r8a7795" and the (non)matching of revision = "ES1.*" to
match with and distinguish between the two SoC variants. The
corresponding entries in the normal of_match_table are present only to
make the optional sanity checks work.
The R-Car H3e-2G (R8A779M1) SoC is a different grading of the R-Car H3
ES3.0 (R8A77951) SoC. It uses the same compatible values for individual
devices, but has an additional compatible value for the root node.
When running on an R-Car H3e-2G SoC, soc_device_match() with soc_id =
"r8a7795" does not return a match. Hence the pin control driver falls
back to the normal of_match_table, and, as the R8A77950 entry is listed
first, incorrectly uses the sub-driver for R-Car H3 ES1.x.
Fix this by moving the entry for R8A77951 before the entry for R8A77950.
Simplify sh_pfc_quirk_match() to only handle R-Car H3 ES1,x, as R-Car H3
ES2.0+ can now be matched using the normal of_match_table as well.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/6cdc5bfa424461105779b56f455387e03560cf66.1626707688.git.geert+renesas@glider.be
When DEBUG is defined (e.g. if CONFIG_DEBUG_PINCTRL=y), the Renesas pin
control driver runs sanity checks against the pin control tables. This
may cause lots of output on the console, and can be annoying in ARM
multi-platform kernels. Fix this by only running the checks when
running on SuperH, or on a DT platform supported by the Renesas pin
controller driver.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210111165013.496897-1-geert+renesas@glider.be
On SuperH and ARM SH/R-Mobile SoCs, the pin control driver handles
GPIOs, too. To reduce code size when compiling a kernel supporting only
modern SoCs, most, but not all, of the GPIO functionality is protected
by checks for CONFIG_PINCTRL_SH_FUNC_GPIO.
Factor out the remaining parts when not needed:
1. sh_pfc_soc_info.{in,out}put describe GPIO pins that have input
resp. output capabilities (SuperH and SH/R-Mobile).
2. sh_pfc_soc_info.gpio_irq{,_size} describe the mapping from GPIO
pins to interrupt numbers (SH/R-Mobile).
3. sh_pfc_gpio_set_direction() configures GPIO direction, called from
the GPIO driver through pinctrl_gpio_direction_{in,out}put()
(SH/R-Mobile). Unfortunately this function cannot just be moved to
drivers/pinctrl/renesas/gpio.c, as it relies on knowledge of
sh_pfc_pinctrl, which is internal to
drivers/pinctrl/renesas/pinctrl.c.
While code size reduction is minimal, this does help in documenting
depencies.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-9-geert+renesas@glider.be
The drivers/pinctrl/sh-pfc subdirectory was originally created to group
pin control drivers for various Renesas SuperH and SH-Mobile platforms.
However, the name "sh-pfc" no longer reflects its contents, as the
directory now contains pin control drivers for Renesas SuperH, ARM32,
and ARM64 SoCs.
Hence rename the subdirectory from drivers/pinctrl/sh-pfc to
drivers/pinctrl/renesas, and the related Kconfig symbol from
PINCTRL_SH_PFC to PINCTRL_RENESAS.
Rename the git branch in MAINTAINERS, too, for consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200909131534.12897-3-geert+renesas@glider.be
