For the SDIO driver, the RESET/ENABLE pins of WILC1000 are controlled
through the SDIO power sequence driver. This commit adds analogous
support for the SPI driver. Specifically, during initialization, the
chip will be ENABLEd and taken out of RESET and during
deinitialization, the chip will be placed back into RESET and disabled
(both to reduce power consumption and to ensure the WiFi radio is
off).
Both RESET and ENABLE GPIOs are optional. However, if the ENABLE GPIO
is specified, then the RESET GPIO should normally also be specified as
otherwise there is no way to ensure proper timing of the ENABLE/RESET
sequence.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221212531.4011609-2-davidm@egauge.net
Smatch complains that there is a double free in probe:
drivers/net/wireless/microchip/wilc1000/spi.c:186 wilc_bus_probe() error: double free of 'spi_priv'
drivers/net/wireless/microchip/wilc1000/sdio.c:163 wilc_sdio_probe() error: double free of 'sdio_priv'
The problem is that wilc_netdev_cleanup() function frees "wilc->bus_data".
That's confusing and a layering violation. Leave the frees in probe(),
delete the free in wilc_netdev_cleanup(), and add some new frees to the
remove() functions.
Fixes: dc8b338f3b ("wilc1000: use goto labels on error path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217150311.GC16611@kili
The USE_SPI_DMA macro name suggests that it could be set to 1 to
control whether or not SPI DMA should be used. However, that's not
what it does. If set to 1, it'll set the SPI messages'
"is_dma_mapped" flag to true, even though the tx/rx buffers aren't
actually DMA mapped by the driver. In other words, setting this flag
to 1 will break the driver.
Best to clean up this confusion by removing the macro altogether.
There is no need to explicitly initialize "is_dma_mapped" because the
message is cleared to zero anyhow, so "is_dma_mapped" is set to false
by default.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211207002453.3193737-1-davidm@egauge.net
Add reset/terminate/repeat command for SPI module. In case of SPI commands
failure, the host should issue a RESET command to WILC chip to recover
from any temporary bus error.
For now, the new command support is added and later the SPI read/write
API's would be modified to make use of these commands for retry mechanism
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210916164902.74629-6-ajay.kathat@microchip.com
The driver so far has always disabled CRC protection. This means any
data corruption that occurrs during the SPI transfers could go
undetected. This patch adds module parameters enable_crc7 and
enable_crc16 to selectively turn on CRC7 (for command transfers) and
CRC16 (for data transfers), respectively.
The default configuration remains unchanged, with both CRC7 and CRC16
off.
The performance impact of CRC was measured by running ttcp -t four
times in a row on a SAMA5 device:
CRC7 CRC16 Throughput: Standard deviation:
---- ----- ----------- -------------------
off off 1720 +/- 48 KB/s
on off 1658 +/- 58 KB/s
on on 1579 +/- 84 KB/s
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-4-davidm@egauge.net
For CMD_SINGLE_READ and CMD_INTERNAL_READ, WILC may insert one or more
zero bytes between the command response and the DATA Start tag (0xf3).
This behavior appears to be undocumented in "ATWILC1000 USER GUIDE"
(https://tinyurl.com/4hhshdts) but we have observed 1-4 zero bytes
when the SPI bus operates at 48MHz and none when it operates at 1MHz.
This code is derived from the equivalent code of the wilc driver in
the linux-at91 repository.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210227172818.1711071-1-davidm@egauge.net
