The downside of using defines in struct ath11k_hw_params.fw.dir is that it's
easy to get it wrong as the full path is not visible. So drop the use of
defines and instead create the patch runtime using a static inline function
ath11k_core_create_firmware_path(). Hopefully this reduces the chances of using
incorrect firmware path.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-8-git-send-email-kvalo@codeaurora.org
To avoid duplicating the logic how the full firmware path is created create a
common function ath11k_core_firmware_request() and convert also qmi.c to use it.
Also remove a useless info print, it's more like a debug message anyway.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-7-git-send-email-kvalo@codeaurora.org
A compromized ath10k peripheral is able to control the size argument
of memcpy in ath10k_pci_hif_exchange_bmi_msg.
The min result from previous line is not used as the size argument
for memcpy. Instead, xfer.resp_len comes from untrusted stream dma
input. The value comes from "nbytes" in ath10k_pci_bmi_recv_data,
which is set inside _ath10k_ce_completed_recv_next_nolock with the line
nbytes = __le16_to_cpu(sdesc.nbytes);
sdesc is a stream dma region which device can write to.
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200616132544.17478-1-bruceshenzk@gmail.com
It is expected that the returned counters by .get_survey are monotonic
increasing. But the data from ath10k gets reset to zero regularly. Channel
active/busy time are then showing incorrect values (less than previous or
sometimes zero) for the currently active channel during successive survey
dump commands.
example:
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 54995 ms
channel busy time: 432 ms
channel receive time: 0 ms
channel transmit time: 59 ms
...
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 32592 ms
channel busy time: 254 ms
channel receive time: 0 ms
channel transmit time: 0 ms
...
The correct way to handle this is to use the non-clearing
WMI_BSS_SURVEY_REQ_TYPE_READ wmi_bss_survey_req_type. The firmware will
then accumulate the survey data and handle wrap arounds.
Tested-on: QCA9984 hw1.0 10.4-3.5.3-00057
Tested-on: QCA988X hw2.0 10.2.4-1.0-00047
Tested-on: QCA9888 hw2.0 10.4-3.9.0.2-00024
Tested-on: QCA4019 hw1.0 10.4-3.6-00140
Fixes: fa7937e3d5 ("ath10k: update bss channel survey information")
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Tested-by: Markus Theil <markus.theil@tu-ilmenau.de>
Tested-by: John Deere <24601deerej@gmail.com>
[sven@narfation.org: adjust commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592232686-28712-1-git-send-email-kvalo@codeaurora.org
When tx status enabled, retry count is updated from tx completion status.
which is not working as expected due to firmware limitation where
firmware can not provide per MSDU rate statistics from tx completion
status. Due to this tx retry count is always 0 in station dump.
Fix this issue by updating the retry packet count from per peer
statistics. This patch will not break on SDIO devices since, this retry
count is already updating from peer statistics for SDIO devices.
Tested-on: QCA9984 PCI 10.4-3.6-00104
Tested-on: QCA9882 PCI 10.2.4-1.0-00047
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591856446-26977-1-git-send-email-vnaralas@codeaurora.org
On wcn3990 we have "per_ce_irq = true". That makes the
ath10k_ce_interrupt_summary() function always return 0xfff. The
ath10k_ce_per_engine_service_any() function will see this and think
that _all_ copy engines have an interrupt. Without checking, the
ath10k_ce_per_engine_service() assumes that if it's called that the
"copy complete" (cc) interrupt fired. This combination seems bad.
Let's add a check to make sure that the "copy complete" interrupt
actually fired in ath10k_ce_per_engine_service().
This might fix a hard-to-reproduce failure where it appears that the
copy complete handlers run before the copy is really complete.
Specifically a symptom was that we were seeing this on a Qualcomm
sc7180 board:
arm-smmu 15000000.iommu: Unhandled context fault:
fsr=0x402, iova=0x7fdd45780, fsynr=0x30003, cbfrsynra=0xc1, cb=10
Even on platforms that don't have wcn3990 this still seems like it
would be a sane thing to do. Specifically the current IRQ handler
comments indicate that there might be other misc interrupt sources
firing that need to be cleared. If one of those sources was the one
that caused the IRQ handler to be called it would also be important to
double-check that the interrupt we cared about actually fired.
Tested-on: WCN3990 SNOC WLAN.HL.3.2.2-00490-QCAHLSWMTPL-1
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200609082015.1.Ife398994e5a0a6830e4d4a16306ef36e0144e7ba@changeid
Currently need ptk/gtk wmi peer flags in wmi peer assoc cmd
are set based on the rsnie and wpaie of the bss from the bss list.
Since this bss list is not updated with current BSSID for AP mode,
we may not find bss from the bss list. Which results in ptk/gtk peer
flags are not set in the wmi peer assoc cmd. Due to this EAPOL frames
are going in data rates instead of management rates.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591771841-25503-1-git-send-email-vnaralas@codeaurora.org
Add support for collecting and dumping the ring backpressure
stats via debugfs. Stats are dumped only if events are
received for the specific ring.
Below command can be used to obtain these stats as part of soc dp stats.
cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
Sample Output - When No stats available:
Backpressure Stats
==================
No Ring Backpressure stats received
Sample Output - When ring bp stats available for specific ring
Backpressure Stats
==================
Ring: REO2SW1_RING
count: 1
hp: 2
tp: 2
seen before: 4ms
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-3-git-send-email-srirrama@codeaurora.org
Add support for dp tx error stats which logs tx failure reasons due
to ring full condition, etc. This stats is added in soc_dp_stats
which was earlier used as soc_rx_stats so that all dp related info
are logged in same file.
Below is an example usage,
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
SOC RX STATS:
err ring pkts: 0
Invalid RBM: 0
<snip>
SOC TX STATS:
Ring Full Failures:
ring0: 4
ring1: 3
ring2: 5
Misc Transmit Failures: 2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-2-git-send-email-srirrama@codeaurora.org
spectral scan control interface is exposed through debugfs eentry.
Relayfs is used to collect the spectral data. These interfaces are
similar to ath10k spectral.
spectral debugfs interfaces are below,
echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-2-git-send-email-periyasa@codeaurora.org
Add direct buffer ring (dbring) with helper API, which is used by the
spectral scan. Initialise the direct buffer ring based on the dma ring
capability, which get announced in the wmi service ready extended event.
This ring is slightly changed from data path rings. Compare to data path
ring this ring shares the hp and tp address to firmware though WMI commands.
Also the replenish buffer size is derived from firmware announcement.
driver receive indication through WMI event
WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-1-git-send-email-periyasa@codeaurora.org
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
This adds support required for configuring min_data_rate of 6GHz oper IE
and peer_he_caps_6ghz in peer assoc command. The Minimum Rate field
indicates the minimum rate, in units of 1 Mb/s, that the non-AP STA is
allowed to use for sending PPDUs as defined in IEEE P802.11ax™/D6.0.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-5-pradeepc@codeaurora.org
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Advertise support for multicast frame registration and update the RX
filter based on the recently added FIF_MCAST_ACTION to allow broadcast
Action frames to be received. This is needed for Device Provisioning
Protocol (DPP) use cases that use broadcast Public Action frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426084733.7889-2-jouni@codeaurora.org
Advertise support for multicast frame registration and update the RX
filter based on the recently added FIF_MCAST_ACTION to allow broadcast
Action frames to be received. This is needed for Device Provisioning
Protocol (DPP) use cases that use broadcast Public Action frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426084733.7889-1-jouni@codeaurora.org
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'thermal_cooling_device_register()' fails, we must undo what has been
allocated so far. So we must go to 'err_thermal_destroy' instead of
returning directly
In case of error in 'ath11k_thermal_register()', the previous
'thermal_cooling_device_register()' call must also be undone. Move the
'ar->thermal.cdev = cdev' a few lines above in order for this to be done
in 'ath11k_thermal_unregister()' which is called in the error handling
path.
Fixes: 2a63bbca06 ("ath11k: add thermal cooling device support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200513201454.258111-1-christophe.jaillet@wanadoo.fr
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507151758.GA4962@embeddedor
HTT EXT stats comes in stream of TLVs spanning over multiple
messages. Currently completion is being sent for each message
which is creating a race where stats_req is being accessed
for filling in second message after the memory is already
freed in release operation. Fix this by issuing completion
once all the messages are received and processed. Driver
knows this info from DONE bit set in htt msg.
Also fix locking required for htt stats.
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589221074-28778-1-git-send-email-pradeepc@codeaurora.org
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200507151120.GA4469@embeddedor
