Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.
Major changes:
mt76
* Specific Absorption Rate (SAR) support
* mt7921: new PCI ids
* mt7921: 160 MHz channel support
iwlwifi
* fix W=1 and sparse warnings
* BNJ hardware support
* add new killer device ids
* support for Time-Aware-SAR (TAS) from the BIOS
* Optimized Connectivity Experience (OCE) scan support
rtw88
* hardware scan
* Specific Absorption Rate (SAR) support
ath11k
* qca6390/wcn6855: report signal and tx bitrate
* qca6390: rfkill support
* qca6390/wcn6855: regdb.bin support
ath5k
* switch to rate table based lookup
wilc1000
* spi: reset/enable GPIO support
* tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (148 commits)
mt76: mt7921: fix a possible race enabling/disabling runtime-pm
wilc1000: Document enable-gpios and reset-gpios properties
wilc1000: Add reset/enable GPIO support to SPI driver
wilc1000: Convert static "chipid" variable to device-local variable
rtw89: 8852a: correct bit definition of dfs_en
rtw88: don't consider deep PS mode when transmitting packet
ath11k: Fix unexpected return buffer manager error for QCA6390
ath11k: add support of firmware logging for WCN6855
ath11k: Fix napi related hang
ath10k: replace strlcpy with strscpy
rtw88: support SAR via kernel common API
rtw88: 8822c: add ieee80211_ops::hw_scan
iwlwifi: mei: wait before mapping the shared area
iwlwifi: mei: clear the ownership when the driver goes down
iwlwifi: yoyo: fix issue with new DBGI_SRAM region read.
iwlwifi: fw: fix some scan kernel-doc
iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ
iwlwifi: mvm: remove card state notification code
iwlwifi: mvm: drop too short packets silently
iwlwifi: mvm: fix AUX ROC removal
...
====================
Link: https://lore.kernel.org/r/20211223141108.78808C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since sock.h is modified relatively often (60 times in the last
12 months) it seems worthwhile to decrease the incremental build
work.
CoDel's header includes net/inet_ecn.h which in turn includes net/sock.h.
codel.h is itself included by mac80211 which is included by much of
the WiFi stack and drivers. Removing the net/inet_ecn.h include from
CoDel breaks the dependecy between WiFi and sock.h.
Commit d068ca2ae2 ("codel: split into multiple files") moved all
the code which actually needs ECN helpers out to net/codel_impl.h,
the include can be moved there as well.
This decreases the incremental build size after touching sock.h
from 4999 objects to 4051 objects.
Fix unmasked missing includes in WiFi drivers.
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221193941.3805147-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix sending rx_buf_sz to ath11k_dp_tx_htt_rx_filter_setup()
to enable pktlog full or lite mode. Depending on mode update the
trace buffer with log type full/lite.
Pktlog lite is a lighter version of pktlog. This can be used to capture
PPDU stats. These are useful for firmware performance debugging.
pktlog lite dumps are enabled using,
echo "0x0 1" > ath11k/IPQ8074 hw2.0/mac0/pktlog_filter
Tested On: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01233-QCAHKSWPL_SILICONZ-1 v2
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-1-jouni@codeaurora.org
QMI sequence fails if caldata file is not available.
It is observed that 'rmmod ath11k' fails if qmi message fails.
With this patch rmmod/insmod is working.
Logs:
Direct firmware load for IPQ8074/caldata.bin failed with error -2
Falling back to user helper
qmi failed to load CAL: IPQ8074/caldata.bin
qmi failed to load board data file:-11
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01699-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606916215-24643-1-git-send-email-akolli@codeaurora.org
debugfs_create_dir() returns an ERR_PTR in case of error, but never a
null pointer. There are a number of places where error-checking code can
accordingly be simplified.
Addresses-Coverity: CID 1497150: Memory - illegal accesses (USE_AFTER_FREE)
Addresses-Coverity: CID 1497158: Memory - illegal accesses (USE_AFTER_FREE)
Addresses-Coverity: CID 1497160: Memory - illegal accesses (USE_AFTER_FREE)
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200927132451.585473-1-alex.dewar90@gmail.com
If CONFIG_ATH11K_DEBUGFS is disabled there are warnings debug.c:
drivers/net/wireless/ath/ath11k/debug.c:36:20: warning: 'htt_bp_lmac_ring' defined but not used [-Wunused-variable]
36 | static const char *htt_bp_lmac_ring[HTT_SW_LMAC_RING_IDX_MAX] = {
| ^~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath11k/debug.c:15:20: warning: 'htt_bp_umac_ring' defined but not used [-Wunused-variable]
15 | static const char *htt_bp_umac_ring[HTT_SW_UMAC_RING_IDX_MAX] = {
| ^~~~~~~~~~~~~~~~
Fix this by refactoring debugfs code to debugfs.c. This also reduces the number
of ifdefs in debug.c and makes it easier to maintain the code.
No functional changes. Compile tested only.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600264523-12939-1-git-send-email-kvalo@codeaurora.org
