The referenced commit added in .config_intr() the part of code which upon
configuration of the IRQ state it also clears up any pending IRQ. If
there were actually pending IRQs, a read on the IRQ status register will
return something non zero. This should not result in the callback
returning an error.
Fix this by returning an error only when the result of the
phy_read_mmd() is negative.
Fixes: e11ef96d44 ("net: phy: aquantia: remove the use of .ack_interrupt()")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Link: https://lore.kernel.org/r/20201109154601.3812574-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RTL8401-internal PHY identifies as RTL8201CP, and the init
sequence in r8169, copied from vendor driver r8168, uses paged
operations. Therefore set the same paged operation callbacks as
for the other Realtek PHY's.
Fixes: cdafdc29ef ("r8169: sync support for RTL8401 with vendor driver")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/69882f7a-ca2f-e0c7-ae83-c9b6937282cd@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Willy Liu <willy.liu@realtek.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Willy Liu <willy.liu@realtek.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems there are cases where the interrupts are handled by another
entity (ie an IRQ controller embedded inside the PHY) and do not need
any other interraction from phylib. For this kind of PHYs, like the
RTL8366RB, add the genphy_handle_interrupt_no_ack() function which just
triggers the link state machine.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Michael Walle <michael@walle.cc>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Also, remove the .did_interrupt() callback since it's not anymore used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the comment describing the phy_mac_interrupt() function, it
it intended to be used by MAC drivers which have noticed a link change
thus its use in the mscc PHY driver is improper and, most probably, was
added just because phy_trigger_machine() was not exported.
Now that we have acces to trigger the link state machine, use directly
the phy_trigger_machine() function to notify a link change detected by
the PHY driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ADIN1300/ADIN1200 support cable diagnostics using TDR.
The cable fault detection is automatically run on all four pairs looking at
all combinations of pair faults by first putting the PHY in standby (clear
the LINK_EN bit, PHY_CTRL_3 register, Address 0x0017) and then enabling the
diagnostic clock (set the DIAG_CLK_EN bit, PHY_CTRL_1 register, Address
0x0012).
Cable diagnostics can then be run (set the CDIAG_RUN bit in the
CDIAG_RUN register, Address 0xBA1B). The results are reported for each pair
in the cable diagnostics results registers, CDIAG_DTLD_RSLTS_0,
CDIAG_DTLD_RSLTS_1, CDIAG_DTLD_RSLTS_2, and CDIAG_DTLD_RSLTS_3, Address
0xBA1D to Address 0xBA20).
The distance to the first fault for each pair is reported in the cable
fault distance registers, CDIAG_FLT_DIST_0, CDIAG_FLT_DIST_1,
CDIAG_FLT_DIST_2, and CDIAG_FLT_DIST_3, Address 0xBA21 to Address 0xBA24).
This change implements support for this using phylib's cable-test support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201103074436.93790-2-alexandru.ardelean@analog.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the PHY powers up, the diagnostics clock isn't enabled (bit 2 in
register PHY_CTRL_1 (0x0012)).
Also, the PHY is not in standby mode, so bit 13 in PHY_CTRL_3 (0x0017) is
always set at power up.
The standby mode and the diagnostics clock are both meant to be for the
cable diagnostics feature of the PHY (in phylib this would be equivalent to
the cable-test support), and for the frame-generator feature of the PHY.
In standby mode, the PHY doesn't negotiate links or manage links.
To use the cable diagnostics/test (or frame-generator), the PHY must be
first set in standby mode, so that the link operation doesn't interfere.
Then, the diagnostics clock must be enabled.
For the cable-test feature, when the operation finishes, the PHY goes into
PHY_UP state, and the config_aneg hook is called.
For the ADIN PHY, we need to make sure that during autonegotiation
configuration/setup the PHY is removed from standby mode and the
diagnostics clock is disabled, so that normal operation is resumed.
This change does that by moving the set of the ADIN1300_LINKING_EN bit (2)
in the config_aneg (to disable standby mode).
Previously, this was set in the downshift setup, because the downshift
retry value and the ADIN1300_LINKING_EN are in the same register.
And the ADIN1300_DIAG_CLK_EN bit (13) is cleared, to disable the
diagnostics clock.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201103074436.93790-1-alexandru.ardelean@analog.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Realtek single-port 2.5Gbps Ethernet PHYs are list as below:
RTL8226-CG: the 1st generation 2.5Gbps single port PHY
RTL8226B-CG/RTL8221B-CG: the 2nd generation 2.5Gbps single port PHY
RTL8221B-VB-CG: the 3rd generation 2.5Gbps single port PHY
RTL8221B-VM-CG: the 2.5Gbps single port PHY with MACsec feature
This patch adds the minimal drivers to manage these transceivers.
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1604281927-9874-1-git-send-email-willy.liu@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the comparisons of u16 integers value and sopass_val with
less than zero for error checking is always false because the values
are unsigned. Fix this by making these variables int. This does not
affect the shift and mask operations performed on these variables
Addresses-Coverity: ("Unsigned compared against zero")
Fixes: 49fc23018e ("net: phy: dp83869: support Wake on LAN")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek single-chip Ethernet PHY solutions can be separated as below:
10M/100Mbps: RTL8201X
1Gbps: RTL8211X
2.5Gbps: RTL8226/RTL8221X
RTL8226 is the first version for realtek that compatible 2.5Gbps single PHY.
Since RTL8226 is single port only, realtek changes its name to RTL8221B from
the second version.
PHY ID for RTL8226 is 0x001cc800 and RTL8226B/RTL8221B is 0x001cc840.
RTL8125 is not a single PHY solution, it integrates PHY/MAC/PCIE bus
controller and embedded memory.
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the check covers only parts of the contexts in which these
functions cannot be called. It fails to detect preemption or interrupt
disabled invocations.
As the functions which contain these warnings invoke mutex_lock() which
contains a broad variety of checks (always enabled or debug option
dependent) and therefore covers all invalid conditions already, there is no
point in having inconsistent warnings in those drivers. The conditional
return is not really valuable in practice either.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. These two pins can config via
4.7k-ohm resistor to 3.3V hw setting, but also config via software setting
(extension page 0xa4 register 0x1c bit13 12 and 11).
The configuration register definitions from table 13 official PHY datasheet:
PHYAD[2:0] = PHY Address
AN[1:0] = Auto-Negotiation
Mode = Interface Mode Select
RX Delay = RX Delay
TX Delay = TX Delay
SELRGV = RGMII/GMII Selection
This table describes how to config these hw pins via external pull-high or pull-
low resistor.
It is a misunderstanding that mapping it as register bits below:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
So I removed these descriptions above and add related settings as below:
14 = reserved
13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay
10:0 = Test && debug settings reserved by realtek
Test && debug settings are not recommend to modify by default.
Fixes: f81dadbcf7 ("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the speed optimization bit on the DP83869 PHY.
Speed optimization, also known as link downshift, enables fallback to 100M
operation after multiple consecutive failed attempts at Gigabit link
establishment. Such a case could occur if cabling with only four wires
(two twisted pairs) were connected instead of the standard cabling with
eight wires (four twisted pairs).
The number of failed link attempts before falling back to 100M operation is
configurable. By default, four failed link attempts are required before
falling back to 100M.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds WoL support on TI DP83869 for magic, magic secure, unicast and
broadcast.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build error by selecting MDIO_DEVRES for MDIO_THUNDER.
Fixes this build error:
ld: drivers/net/phy/mdio-thunder.o: in function `thunder_mdiobus_pci_probe':
drivers/net/phy/mdio-thunder.c:78: undefined reference to `devm_mdiobus_alloc_size'
Fixes: 379d7ac7ca ("phy: mdio-thunder: Add driver for Cavium Thunder SoC MDIO buses.")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: netdev@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add kerneldoc for the core PHY data structures, a few inline functions
and exported functions which are not already documented.
v2
Typos
g/phy/PHY/s
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM72113 features a 28nm integrated EPHY, add an entry to the driver for
it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the fiber advertisement for speed and duplex modes with the
100base-FX full and half linkmode entries.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to advertise the Fiber connection if the strap or the
op-mode is configured for 100Base-FX.
Auto negotiation is not supported on this PHY when in fiber mode.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
