In ipa_mem_valid(), wait until regions have been marked in the memory
region bitmap, and check all that are not found there to ensure they
are not required.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test in ipa_mem_valid() to ensure no memory region is defined
more than once, using a bitmap to record each defined memory region.
Skip over undefined regions when checking (we can have any number of
those).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce ipa_mem_id_valid(), and use it to check defined memory
regions to ensure they are valid for a given version of IPA.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new function that indicates whether a given memory
region is required for a given version of IPA hardware. Use it to
verify that all required regions are present during initialization.
Reorder the definitions of the memory region IDs to be based on
the version in which they're first defined. Use "+" rather than
"and above" where defining the IPA versions in which memory IDs are
used, and indicate which regions are optional (many are not).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the memory configuration data array to ipa_mem_valid() for
validation, and use that rather than assuming it's already been
recorded in the IPA structure. Move the memory data array size
check into ipa_mem_valid().
Call ipa_mem_valid() early in ipa_mem_init(), and only proceed with
assigning the memory array pointer and size if it is found to be
valid.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the memory region validation check so it happens earlier when
initializing the driver, at init time rather than config time (i.e.,
before access to hardware is required).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only thing done by ipa_mem_valid_one() that requires hardware
access is the check for whether all regions fit within the size of
IPA local memory specified by an IPA register.
Introduce ipa_mem_size_valid() to implement this verification and
stop doing so in ipa_mem_valid_one(). Call the new function from
ipa_mem_config() (which is also the caller of ipa_mem_valid()).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, memory regions are validated in the loop that initializes
them. Instead, validate them separately.
Rename ipa_mem_valid() to be ipa_mem_valid_one(). Define a *new*
function named ipa_mem_valid() that performs validation of the array
of memory regions provided. This function calls ipa_mem_valid_one()
for each region in turn.
Skip validation for any "empty" region descriptors, which have zero
size and are not preceded by any canary values. Issue a warning for
such descriptors if the offset is non-zero.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do memory region descriptor validation unconditionally, rather than
having it depend on IPA_VALIDATION being defined.
Pass the address of a memory region descriptor rather than a memory
ID to ipa_mem_valid().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the memory region ID in the memory descriptor structure. This
is a move toward *not* indexing the array by the ID, but for now we
must still specify those index values. Define an explicitly
undefined region ID, value 0, so uninitialized entries in the array
won't use an otherwise valid ID.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new pseudo memory region identifer that specifies the
offset at the end of IPA resident memory. Use it instead of
IPA_MEM_UC_EVENT_RING in places where the size of that region was
defined to be 0.
The size of the IPA_MEM_END_MARKER pseudo region must be zero.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c88c34fcf8.
The RMNet driver now supports inline checksum offload.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with IPA v4.5, IP payload checksum offload is implemented
differently.
Prior to v4.5, the IPA hardware appends an rmnet_map_dl_csum_trailer
structure to each packet if checksum offload is enabled in the
download direction (modem->AP). In the upload direction (AP->modem)
a rmnet_map_ul_csum_header structure is prepended before each sent
packet.
Starting with IPA v4.5, checksum offload is implemented using a
single new rmnet_map_v5_csum_header structure which sits between
the QMAP header and the packet data. The same header structure
is used in both directions.
The new header contains a header type (CSUM_OFFLOAD); a checksum
flag; and a flag indicating whether any other headers follow this
one. The checksum flag indicates whether the hardware should
compute (and insert) the checksum on a sent packet. On a received
packet the checksum flag indicates whether the hardware confirms the
checksum value in the payload is correct.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA configuration data includes an array of memory region
descriptors. That was a fixed-size array at one time, but
at some point we started defining it such that it was only
as big as required for a given platform. The actual number
of entries in the array is recorded in the configuration data
along with the array.
A loop in ipa_mem_config() still assumes the array has entries
for all defined memory region IDs. As a result, this loop can
go past the end of the actual array and attempt to write
"canary" values based on nonsensical data.
Fix this, by stashing the number of entries in the array, and
using that rather than IPA_MEM_COUNT in the initialization loop
found in ipa_mem_config().
The only remaining use of IPA_MEM_COUNT is in a validation check
to ensure configuration data doesn't have too many entries.
That's fine for now.
Fixes: 3128aae8c4 ("net: ipa: redefine struct ipa_mem_data")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In gsi_irq_setup(), two registers are written with the intention of
disabling inter-EE channel and event IRQs.
But the wrong registers are used (and defined); the ones used are
read-only registers that indicate whether the interrupt condition is
present.
Define the mask registers instead of the status registers, and use
them to disable the inter-EE interrupt types.
Fixes: 46f748ccaf ("net: ipa: explicitly disallow inter-EE interrupts")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20210505223636.232527-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPA initialization includes loading some firmware. This step is
done either by the modem or by the AP under Trust Zone. If the
AP loads firmware, the name of the firmware file is currently
hard-coded ("ipa_fws.mdt").
Add the ability to specify the relative path of the firmware file to
use in a property in the Device Tree IPA node. If the property is
not found (or if any other error occurs attempting to get it), fall
back to using a default relative path.
Use the "old" fixed name as the default. Rename the symbol that
represents this default to emphasize its purpose.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SM8350 SoC, which includes IPA version 4.9.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SC7280 SoC, which includes IPA version 4.11.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the SDX55 SoC, which includes IPA version 4.5.
Starting with IPA v4.5, a few of the memory regions have a different
number of "canary" values; update comments in the where the region
identifers are defined to accurately reflect that.
I'll note three differences in SDX55 versus the other two existing
platforms (SDM845 and SC7180):
- SDX55 uses a 32-bit Linux kernel
- SDX55 has four interconnects rather than three
- SDX55 uses IPA v4.5, which uses inline checksum offload
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checksum offload for IPA v4.5+ is implemented differently, using
"inline" offload (which uses a common header format for both upload
and download offload).
The IPA hardware must be programmed to enable MAP checksum offload,
but the RMNet driver is responsible for interpreting checksum
metadata supplied with messages.
Currently, the RMNet driver does not support inline checksum offload.
This support is imminent, but until it is available, do not allow
newer versions of IPA to specify checksum offload for endpoints.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some time ago changes were made to stop referring to clearing the
hardware pipeline as a "tag process." Fix a comment to use the
newer terminology.
Get rid of a pointless double-negation of the Boolean toward_ipa
flag in ipa_endpoint_config().
make ipa_endpoint_exit_one() private; it's only referenced inside
"ipa_endpoint.c".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are place holder functions in the GSI code that do nothing.
Remove these, knowing we can add something back in their place if
they're really needed someday.
Some of these are inverse functions (such as teardown to match setup).
Explicitly comment that there is no inverse in these cases.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are place holder functions in the IPA code that do nothing.
For the most part these are inverse functions, for example, once the
routing or filter tables are set up there is no need to perform any
matching teardown activity at shutdown, or in the case of an error.
These can be safely removed, resulting in some code simplification.
Add comments in these spots making it explicit that there is no
inverse.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ipa_modem_stop(), if the modem netdev pointer is non-null we call
ipa_stop(). We check for an error and if one is returned we handle
it. But ipa_stop() never returns an error, so this extra handling
is unnecessary. Simplify the code in ipa_modem_stop() based on the
knowledge no error handling is needed at this spot.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ipa_modem_start(), we set endpoint netdev pointers before the
network device is registered. If registration fails, we don't undo
those assignments. Instead, wait to assign the netdev pointer until
after registration succeeds.
Set these endpoint netdev pointers to NULL in ipa_modem_stop()
before unregistering the network device.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On IPA v3.5.1, the sequencer type for the modem TX endpoint does not
define the replication portion in the same way the downstream code
does. This difference doesn't affect the behavior of the upstream
code, but I'd prefer the two code bases use the same configuration
value here.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I no longer know why a validation check ensured the size of an entry
passed to gsi_trans_pool_init() was restricted to be a multiple of 8.
For 32-bit builds, this condition doesn't always hold, and for DMA
pools, the size is rounded up to a power of 2 anyway.
Remove this restriction.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Entries in an IPA route or filter table are 64-bit little-endian
addresses, each of which refers to a routing or filtering rule.
The format of these table slots are fixed, but IPA_TABLE_ENTRY_SIZE
is used to define their size. This symbol doesn't really add value,
and I think it unnecessarily obscures what a table entry *is*.
So get rid of IPA_TABLE_ENTRY_SIZE, and just use sizeof(__le64) in
its place throughout the code.
Update the comments in "ipa_table.c" to provide a little better
explanation of these table slots.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent patch avoided doing 64-bit modulo operations by checking
the alignment of some DMA allocations using only the lower 32 bits
of the address.
David Laight pointed out (after the fix was committed) that DMA
allocations might already satisfy the alignment requirements. And
he was right.
Remove the alignment checks that occur after DMA allocation requests,
and update comments to explain why the constraint is satisfied. The
only place IPA_TABLE_ALIGN was used was to check the alignment; it is
therefore no longer needed, so get rid of it.
Add comments where GSI_RING_ELEMENT_SIZE and the tre_count and
event_count channel data fields are defined to make explicit they
are required to be powers of 2.
Revise a comment in gsi_trans_pool_init_dma(), taking into account
that dma_alloc_coherent() guarantees its result is aligned to a page
size (or order thereof).
Don't bother printing an error if a DMA allocation fails.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the SC7180 configuration data file so that its name is
derived from its IPA version.
Update a few other references to the code that talk about the SC7180
rather than just IPA v4.2.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the SDM845 configuration data file so that its name is
derived from its IPA version. I am not aware of any special IPA
behavior or handling that would be based on a specific SoC (as
opposed to a specific version of the IPA it contains).
Update a few other references to the code that talk about the SDM845
rather than just IPA v3.5.1.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't typically need much information about modem endpoints.
Normally we need to specify information about modem endpoints in
configuration data in only two cases:
- When a modem TX endpoint supports filtering
- When another endpoint's configuration refers to it
For the first case, the AP initializes the filter table, and must
know how many endpoints (AP and modem) support filtering. An
example of the second case is the AP->modem TX endpoint, which
defines the modem<-AP RX endpoint as its status endpoint.
There is one exception to this, and it's due to a hardware quirk.
For IPA v4.2 (only) there is a problem related to allocating GSI
channels. And to work around this, the AP allocates *all* GSI
channels at startup time--including those used by the modem.
Get rid of the configuration information for two endpoints not
required for the SDM845. SC7180 runs IPA v4.2, so we can't
eliminate any modem endpoint definitions there.
Two more minor changes:
- Reorder the members defined for the ipa_endpoint_name enumerated
type to match the order used in configuration data files when
defining endpoints.
- Add a new name, IPA_ENDPOINT_MODEM_DL_NLO_TX, which can be used
for IPA v4.5+.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The backward compatibility register value is a platform-specific
property that is not stored in the platform data. Create a data
field where this can be represented, and get rid ipa_reg_bcr_val().
This register is not present starting with IPA v4.5.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix all warnings produced when running:
scripts/kernel-doc -none drivers/net/ipa/*.[ch]
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA versions 3.0 and 3.1 support up to 8 resource groups. There is
some interest in supporting these older versions of the hardware, so
update the resource configuration code to program resource limits
for these groups if specified.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arrays of source and destination resource limits defined in
configuration data are of a fixed size--which is the maximum number
of resource groups supported for any platform. Most platforms will
use fewer than that many groups.
Add new members to the ipa_rsrc_group_id enumerated type to define
the number of source and destination resource groups are defined for
the platform. (This type is defined for each platform in its data
file.)
Add a new field to the resource configuration data that indicates
how many of the source and destination resource groups are actually
used for the platform, and initialize it with the count value. This
allows us to determine the number of groups defined for the platform
without exposing the ipa_rsrc_group_id enumerated type.
As a result, we no longer need ipa_resource_group_src_count()
and ipa_resource_group_dst_count(), because each platform now
defines its supported number of resource groups. So get rid of
those two functions.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the resource data pointer to ipa_resource_config_src() and
ipa_resource_config_dst() to be used for configuring resource
limits.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipa_resource_src and ipa_resource_dst structures are identical
in form, so just replace them with a single structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace IPA_RESOURCE_GROUP_SRC_MAX and IPA_RESOURCE_GROUP_DST_MAX
with a single symbol, IPA_RESOURCE_GROUP_MAX.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most platforms have the same set of source and destination resource
types. But some older platforms have some additional ones, and it's
possible different resources will be used in the future.
Move the definition of the ipa_resource_type enumerated type so it
is defined for each platform in its configuration data file. This
permits each to have a distinct set of resources.
Shorten the data files slightly, by putting the min and max limit
values on the same line.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the type field from the ipa_resource_src and ipa_resource_dst
structures, and instead use that value as the index into the arrays
of source and destination resources.
Change ipa_resource_config_src() and ipa_resource_config_dst() so
the resource type is passed in as an argument.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine the ipa_resource_type_src and ipa_resource_type_dst
enumerated types into a single enumerated type, ipa_resource_type.
Assign value 0 to the first element for the source and destination
types, so their numeric values are preserved. Add some additional
commentary where these are defined, stating explicitly that code
assumes the first source and first destination member must have
numeric value 0.
Fix the kerneldoc comments for the ipa_gsi_endpoint_data structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the SDM845 configuration data defines resource limits for
the first two resource groups (for both source and destination
resource types). The hardware supports additional resource groups,
and we should program the resource limits for those groups as well.
Even the "unused" destination resource group (number 2) should have
non-zero limits programmed in some cases, to ensure correct operation.
Add these missing resource group limit definitions to the SDM845
configuration data.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a new ipa_resource_group_id enumerated type, whose members
have numeric values that match the resource group number used when
programming the hardware. Each platform supports a different number
of source and destination resource groups, so define the type
separately for each platform in its configuration data file.
Use these new symbolic values when specifying the resource group an
endpoint is associated with. And use them to index the limits
arrays for source and destination resources, making it clearer how
these values are used.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the number of resource groups supported by the hardware is less
than a certain number, we return early in ipa_resource_config_src()
and ipa_resource_config_dst() (to avoid programming resource limits
for non-existent groups).
Unfortunately, these checks are off by one. Fix this problem in the
four places it occurs.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the IPA resource-related code into a new source file,
"ipa_resource.c", and matching header file "ipa_resource.h".
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPA v4.5 (GSI v2.5) supports a larger set of channel protocols, and
adds an additional field to hold the most-significant bits of the
protocol identifier on a channel.
Add an inline function that encodes the protocol (including the
extra bits for newer versions of IPA), and define some additional
protocols. At this point we still use only GPI protocol.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each GSI channel has a CNTXT_1 register that encodes the size of its
ring buffer. The size of the field that records that is increased
starting at IPA v4.9. Replace the use of a fixed-size field mask
with a new inline function that encodes that size value.
Similarly, the size of GSI event rings can be larger starting with
IPA v4.9, so create a function to encode that as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main purpose of this is to extend these GSI register definitions
to support additional IPA versions.
This patch makes some minor updates to "gsi_reg.h":
- Define a DB_IN_BYTES field in the channel QOS register
- Add some comments clarifying when certain fields are valid
- Add the definition of GSI_CH_DB_STOP channel command
- Add a couple of blank lines
- Move one comment and indent another
- Delete two unused register definitions at the end.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
