For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Link: https://lore.kernel.org/r/2fef280d8409ab0100c26c6ac7050227defd098d.1627818365.git.tommyhebb@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make 'struct mmc_request' contain a pointer to the request's
'struct bio_crypt_ctx' directly, instead of extracting a 32-bit DUN from
it which is a cqhci-crypto specific detail.
This keeps the cqhci crypto specific details in the cqhci module, and it
makes mmc_core and mmc_block ready for MMC crypto hardware that accepts
the DUN and/or key in a way that is more flexible than that which will
be specified by the eMMC v5.2 standard. Exynos SoCs are an example of
such hardware, as their inline encryption hardware takes keys directly
(it has no concept of keyslots) and supports 128-bit DUNs.
Note that the 32-bit DUN length specified by the standard is very
restrictive, so it is likely that more hardware will support longer DUNs
despite it not following the standard. Thus, limiting the scope of the
32-bit DUN assumption to the place that actually needs it is warranted.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210721154738.3966463-1-ebiggers@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver has had problems when handling data errors. Add fault
injection support so that the abort handling can be easily triggered and
regression-tested. A hrtimer is used to indicate a data CRC error at
various points during the data transfer.
Note that for the recent problem with hangs in the case of some data CRC
errors, a udelay(10) inserted at the start of send_stop_abort() greatly
helped in triggering the error, but I've not included this as part of
the fault injection support since it seemed too specific.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210701080534.23138-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When a Data CRC interrupt is received, the driver disables the DMA, then
sends the stop/abort command and then waits for Data Transfer Over.
However, sometimes, when a data CRC error is received in the middle of a
multi-block write transfer, the Data Transfer Over interrupt is never
received, and the driver hangs and never completes the request.
The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
"before assertion of SWR". Do these operations in the recommended
order. With this change the Data Transfer Over is always received
correctly in my tests.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210630102232.16011-1-vincent.whitchurch@axis.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull MMC fixes from Ulf Hansson
"MMC core:
- Clear flags before allowing to retune
MMC host:
- sdhci: Clear unused bounce buffer at DMA mmap error path
- sdhci: Fix warning message when accessing RPMB in HS400 mode
- sdhci-of-arasan: Use clock-frequency property to update clk_xin
- mtk-sd: Fixup compatible string for MT8195"
* tag 'mmc-v5.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci: Fix warning message when accessing RPMB in HS400 mode
dt-bindings: mmc: change compatiable string for MT8195 mmc host IP
mmc: sdhci: Clear unused bounce buffer at DMA mmap error path
phy: intel: Fix for warnings due to EMMC clock 175Mhz change in FIP
mmc: sdhci-of-arasan: Use clock-frequency property to update clk_xin
mmc: core: clear flags before allowing to retune
Pull KUnit update from Shuah Khan:
"Fixes and features:
- add support for skipped tests
- introduce kunit_kmalloc_array/kunit_kcalloc() helpers
- add gnu_printf specifiers
- add kunit_shutdown
- add unit test for filtering suites by names
- convert lib/test_list_sort.c to use KUnit
- code organization moving default config to tools/testing/kunit
- refactor of internal parser input handling
- cleanups and updates to documentation
- code cleanup related to casts"
* tag 'linux-kselftest-kunit-fixes-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (29 commits)
kunit: add unit test for filtering suites by names
kasan: test: make use of kunit_skip()
kunit: test: Add example tests which are always skipped
kunit: tool: Support skipped tests in kunit_tool
kunit: Support skipped tests
thunderbolt: test: Reinstate a few casts of bitfields
kunit: tool: internal refactor of parser input handling
lib/test: convert lib/test_list_sort.c to use KUnit
kunit: introduce kunit_kmalloc_array/kunit_kcalloc() helpers
kunit: Remove the unused all_tests.config
kunit: Move default config from arch/um -> tools/testing/kunit
kunit: arch/um/configs: Enable KUNIT_ALL_TESTS by default
kunit: Add gnu_printf specifiers
lib/cmdline_kunit: Remove a cast which are no-longer required
kernel/sysctl-test: Remove some casts which are no-longer required
thunderbolt: test: Remove some casts which are no longer required
mmc: sdhci-of-aspeed: Remove some unnecessary casts from KUnit tests
iio: Remove a cast in iio-test-format which is no longer required
device property: Remove some casts in property-entry-test
Documentation: kunit: Clean up some string casts in examples
...
When an eMMC device is being run in HS400 mode, any access to the
RPMB device will cause the error message "mmc1: Invalid UHS-I mode
selected". This happens as a result of tuning being disabled before
RPMB access and then re-enabled after the RPMB access is complete.
When tuning is re-enabled, the system has to switch from HS400
to HS200 to do the tuning and then back to HS400. As part of
sequence to switch from HS400 to HS200 the system is temporarily
put into HS mode. When switching to HS mode, sdhci_get_preset_value()
is called and does not have support for HS mode and prints the warning
message and returns the preset for SDR12. The fix is to add support
for MMC and SD HS modes to sdhci_get_preset_value().
This can be reproduced on any system running eMMC in HS400 mode
(not HS400ES) by using the "mmc" utility to run the following
command: "mmc rpmb read-counter /dev/mmcblk0rpmb".
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 52983382c7 ("mmc: sdhci: enhance preset value function")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210624163045.33651-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull clk updates from Stephen Boyd:
"This round has a diffstat dominated by Qualcomm clk drivers. Honestly
though that's just a bunch of data so the diffstat reflects that.
Looking beyond that there's just a bunch of updates all around in
various clk drivers. Renesas and NXP (for i.MX) are two SoC vendors
that have a lot of patches in here.
Overall the driver changes look to be mostly enabling more clks and
non-critical fixes that we could hold until the next merge window.
I'm especially excited about the series from Arnd that graduates
clkdev to be the only implementation of clk_get() and clk_put().
That's a good step in the right direction to migreate eveerything over
to the common clk framework. Now we don't have to worry about clkdev
specific details, they're just part of the clk API now.
Core:
- clkdev is now the only option, i.e. clk_get()/clk_put() is
implemented in only one place in the kernel instead of in
drivers/clk/clkdev.c and in architectures that want their own
implementation
New Drivers:
- Texas Instruments' LMK04832 Ultra Low-Noise JESD204B Compliant
Clock Jitter Cleaner With Dual Loop PLLs
- Qualcomm MDM9607 GCC
- Qualcomm SC8180X display clks
- Qualcomm SM6125 GCC
- Qualcomm SM8250 CAMCC (camera)
- Renesas RZ/G2L SoC
- Hisilicon hi3559A SoC
Updates:
- Stop using clock-output-names in ST clk drivers (yay!)
- Support secure mode of STM32MP1 SoCs
- Improve clock support for Actions S500 SoC
- duty cycle setting support on qcom clks
- Add TI am33xx spread spectrum clock support
- Use determine_rate() for the Amlogic pll ops instead of
round_rate()
- Restrict Amlogic gp0/1 and audio plls range on g12a/sm1
- Improve Amlogic axg-audio controller error on deferral
- Add NNA clocks on Amlogic g12a
- Reduce memory footprint of Rockchip PLL rate tables
- A fix for the newly added Rockchip rk3568 clk driver
- Exported clock for the newly added Rockchip video decoder
- Remove audio ipg clock from i.MX8MP
- Remove deprecated legacy clock binding for i.MX SCU clock driver
- Use common clk-imx8qxp for both i.MX8QXP and i.MX8QM
- Add multiple clocks to clk-imx8qxp driver (enet, hdmi, lcdif,
audio, parallel interface)
- Add dedicated clock ops for i.MX paralel interface
- Different fixes for clocks controlled by ATF on i.MX SoCs
- Add A53/A72 frequency scaling support i.MX clk-scu driver
- Add special case for DCSS clock on suspend for i.MX clk-scu driver
- Add parent save/restore on suspend/resume to i.MX clk-scu driver
- Skip runtime PM enablement for CPU clocks in i.MX clk-scu driver
- Remove the sys1_pll/sys2_pll clock gates for i.MX8MQ and their
bindings
- Tegra clk driver no longer deasserts resets on clk_enable as it
gets in the way of certain power-up sequences
- Fix compile testing for Tegra clk driver
- One patch to fix a divider on the Allwinner v3s Audio PLL
- Add support for CPU core clock boost modes on Renesas R-Car Gen3
- Add ISPCS (Image Signal Processor) clocks on Renesas R-Car V3U
- Switch SH/R-Mobile and R-Car "DIV6" clocks to .determine_rate() and
improve support for multiple parents
- Switch Renesas RZ/N1 divider clocks to .determine_rate()
- Add ZA2 (Audio Clock Generator) clock on Renesas R-Car D3
- Convert ar7 to common clk framework
- Convert ralink to common clk framework"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (161 commits)
clk: zynqmp: Handle divider specific read only flag
clk: zynqmp: Use firmware specific mux clock flags
clk: zynqmp: Use firmware specific divider clock flags
clk: zynqmp: Use firmware specific common clock flags
clk: lmk04832: Use of match table
clk: lmk04832: Depend on SPI
clk: stm32mp1: new compatible for secure RCC support
dt-bindings: clock: stm32mp1 new compatible for secure rcc
dt-bindings: reset: add MCU HOLD BOOT ID for SCMI reset domains on stm32mp15
dt-bindings: reset: add IDs for SCMI reset domains on stm32mp15
dt-bindings: clock: add IDs for SCMI clocks on stm32mp15
reset: stm32mp1: remove stm32mp1 reset
clk: hisilicon: Add clock driver for hi3559A SoC
dt-bindings: Document the hi3559a clock bindings
clk: si5341: Add sysfs properties to allow checking/resetting device faults
clk: si5341: Add silabs,iovdd-33 property
clk: si5341: Add silabs,xaxb-ext-clk property
clk: si5341: Allow different output VDD_SEL values
clk: si5341: Update initialization magic
clk: si5341: Check for input clock presence and PLL lock on startup
...
When DMA-mapping of the bounce buffer fails, the driver tries to fall
back, but it leaves the allocated host->bounce_buffer although its
size is zero. Later on, the driver checks the use of bounce buffer
with host->bounce_buffer pointer, and it tries to use the buffer
incorrectly, resulting in Oops.
This patch clears the release the unused buffer and clears the
bounce_buffer pointer for addressing the problem.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20210611101948.18972-1-tiwai@suse.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The card timing and the bus frequency are not changed atomically with
respect to calls to the set_clock() callback in the driver. The result
is the driver sees a transient state where there's a mismatch between
the two and thus the inputs to the phase correction calculation
formula are garbage.
Switch from dev_warn() to dev_dbg() to avoid noise in the normal case,
though the change does make bad configurations less likely to be
noticed.
Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210607013020.85885-1-andrew@aj.id.au
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The hardware provides capability configuration registers for each SDHCI
in the global configuration space for the SD controller. Writes to the
global capability registers are mirrored to the capability registers in
the associated SDHCI. Configuration of the capabilities must be written
through the mirror registers prior to initialisation of the SDHCI.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210524073308.9328-5-steven_lee@aspeedtech.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
