Inserting an SD-card on an Intel NUC10i3FNK4 (which contains a GL9755)
results in the message:
mmc0: 1.8V regulator output did not become stable
Following this message, some cards work (sometimes), but most cards fail
with EILSEQ. This behaviour is observed on Debian 10 running kernel
4.19.188, but also with 5.8.18 and 5.11.15.
The driver currently waits 5ms after switching on the 1.8V regulator for
it to become stable. Increasing this to 10ms gets rid of the warning
about stability, but most cards still fail. Increasing it to 20ms gets
some cards working (a 32GB Samsung micro SD works, a 128GB ADATA
doesn't). At 50ms, the ADATA works most of the time, and at 100ms both
cards work reliably.
Signed-off-by: Daniel Beer <dlbeer@gmail.com>
Acked-by: Ben Chuang <benchuanggli@gmail.com>
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210424081652.GA16047@nyquist.nev
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GL9763E enters ASPM L1 state after a very short idle in default,
even during a burst of request. So the R/W performance of GL9763E
is low with some platforms, which support ASPM mechanism, due to
entering ASPM L1 state very frequently in R/W process. Set the L1
entry delay bits in vendor-specific register to 0x3FF to enlarge
the idle period to 260us for improving the R/W performance
of GL9763E.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Link: https://lore.kernel.org/r/20210115054736.27769-1-reniuschengl@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable MSI interrupt for GL9750/GL9755. Some platforms
do not support PCI INTx and devices can not work without
interrupt. Like messages below:
[ 4.487132] sdhci-pci 0000:01:00.0: SDHCI controller found [17a0:9755] (rev 0)
[ 4.487198] ACPI BIOS Error (bug): Could not resolve symbol [\_SB.PCI0.PBR2._PRT.APS2], AE_NOT_FOUND (20190816/psargs-330)
[ 4.487397] ACPI Error: Aborting method \_SB.PCI0.PBR2._PRT due to previous error (AE_NOT_FOUND) (20190816/psparse-529)
[ 4.487707] pcieport 0000:00:01.3: can't derive routing for PCI INT A
[ 4.487709] sdhci-pci 0000:01:00.0: PCI INT A: no GSI
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Tested-by: Raul E Rangel <rrangel@chromium.org>
Fixes: e51df6ce66 ("mmc: host: sdhci-pci: Add Genesys Logic GL975x support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200219092900.9151-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the GL9750 and GL9755 chipsets.
Enable v4 mode and wait 5ms after set 1.8V signal enable for GL9750/
GL9755. Fix the value of SDHCI_MAX_CURRENT register and use the vendor
tuning flow for GL9750.
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
