Provide a list of ->available_scan_masks which match the device's
capabilities. Basically, these devices are able to scan from 0 to N, N
being the highest voltage channel requested by the user. The temperature
can be included or not, but cannot be retrieved alone.
The consequence is, instead of reading and pushing to the IIO buffers
all channels each time, the "minimum" number of channels will be scanned
and pushed based on the ->active_scan_mask.
For example, if the user wants channels 1, 4 and 5, all channels from
0 to 5 will be scanned and pushed to the IIO buffers. The core will then
filter out the unneeded samples based on the ->active_scan_mask that has
been selected and only channels 1, 4 and 5 will be available to the user
in the shared buffer.
Provide a comment in the code explaining this logic.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20210921115408.66711-5-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC controller has a trimming register for fine-tune the reference
voltage. The trimming value comes from the OTP register which will be
written during chip production. This patch will read this OTP value and
configure it to the ADC register when the ADC controller probes and using
dts property "aspeed,trim-data-valid" to determine whether to execute this
flow.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-12-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In ast2600, ADC integrate dividing circuit at last input channel for
battery sensing. This patch use the dts property "battery-sensing" to
enable this feature makes the last channel of each adc can tolerance
higher voltage than reference voltage. The offset interface of ch7 will
be separated when enabling the battery sensing mode.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-11-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC clock formula is
ast2400/2500:
ADC clock period = PCLK * 2 * (ADC0C[31:17] + 1) * (ADC0C[9:0] + 1)
ast2600:
ADC clock period = PCLK * 2 * (ADC0C[15:0] + 1)
They all have one fixed divided 2 and the legacy driver didn't handle it.
This patch register the fixed factory clock device as the parent of ADC
clock scaler to fix this issue.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-8-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch refactors the model data structure to distinguish the
function form different versions of aspeed ADC.
- Rename the vref_voltage to vref_fixed_mv and add vref_mv driver data
When driver probe will check vref_fixed_mv value and store it to vref_mv
which isn't const value.
- Add num_channels
Make num_channles of iio device can be changed by different model_data
- Add need_prescaler flag and scaler_bit_width
The need_prescaler flag is used to tell the driver the clock divider needs
another Prescaler and the scaler_bit_width to set the clock divider
bitfield width.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20210922081520.30580-3-billy_tsai@aspeedtech.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7793 datasheet: " The DOUT/RDY falling edge can be
used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-4-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Correct IRQ flag here is falling.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7780 datasheet: " The DOUT/Figure 22 RDY falling edge
can be used as an interrupt to a processor"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-3-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IRQ type in ad_sigma_delta_info struct was missing.
In Sigma-Delta devices the SDO line is also used as an interrupt.
Leaving IRQ on level instead of falling might trigger a sample read
when the IRQ is enabled, as the SDO line is already low. Not sure
if SDO line will always immediately go high in ad_sd_buffer_postenable
before the IRQ is enabled.
Also the datasheet seem to explicitly say the falling edge of the SDO
should be used as an interrupt:
>From the AD7192 datasheet: "The DOUT/RDY falling edge can be used
as an interrupt to a processor,"
Fixes: da4d3d6bb9 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210906065630.16325-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently when a timeout occurs in rzg2l_adc_hw_init the error -EBUSY is
assigned to ret but the error code is used as the function is hard-coded
to return 0. The variable ret is 0 before entering the while-loop hence
the fix is just to return ret at the end of the function to return the
success 0 or -EBUSY return code.
Addresses-Coverity: ("Unused value")
Fixes: d484c21bac ("iio: adc: Add driver for Renesas RZ/G2L A/D converter")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210817172111.495897-1-colin.king@canonical.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the driver to platform specific structures. This means:
- create a register layout struct that will hold offsets for registers
- create a platform struct that will hold platform information (number of
channels, indexes for different channels and pointer to layout struct)
- convert specific macros that are platform dependent into platform variables
This step is in fact a no-op, but allows the driver to be more flexible
and for future enhancement including adding new platforms that are partly
compatible with the current driver and differ slightly in register layout
or capabilities for example.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Link: https://lore.kernel.org/r/20210901123013.329792-5-eugen.hristev@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for selecting the voltage reference from the devicetree.
This change is required to get valid readings with all three
vref hardware configurations supported by the ADC.
For instance if the ADC isn't provided with an external reference,
the sample request must specify an internal voltage reference to get a
valid reading.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-4-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver supports devices with 14-bit and 16-bit sample sizes.
This implies different SPI transfer lengths which are not always handled
properly by some SPI controllers.
To work around this limitation, define a big endian buffer used to split
the buffer into two 8-bit messages in the event that the controller
doesn't support 14-bit or 16-bit transfers.
A separate buffer is introduced here to avoid performing operations on
types of different endianness.
Since all transfers use the same bits_per_word value, move that logic to
the probe function, and let transfers default to the value defined in
the struct spi_device.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Link: https://lore.kernel.org/r/20210815213309.2847711-3-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull IIO and staging driver updates from Greg KH:
"Here is the big set of staging and IIO driver updates for 5.15-rc1.
Also included in here are the counter driver subsystem updates as the
IIO drivers needed them.
Lots of churn in some staging drivers, we dropped the "old" rtl8188eu
driver and replaced it with a newer version of the driver that had
been maintained out-of-tree by Larry with the end goal of actually
being able to get this driver out of staging eventually. Despite that
driver being "newer" the line count of this pull request is going up.
Some drivers moved out of staging as well, which is always nice to
see, that is why there are additions to the mfc and misc driver
subsystems. All of these were acked by the various subsystem
maintainers involved.
But by far, as normal, it's coding style cleanups all over the
drivers/staging/ tree in here.
Full details of these changes are in the shortlog.
All of these have been in linux-next for a while with no reported
problems"
[ Note: the r8188eu merge clashed with commit 89939e8906 ("staging:
rtlwifi: use siocdevprivate") from the networking tree. When resolving
the issue, I noted that the whole r8188eu rtw_android code is dead
since commit ae7471cae0 ("staging: r8188eu: remove rtw_ioctl
function").
End result: the merge resolution was to throw all of that away,
rather than do the mindless fixup to code that isn't actually
reachable - Linus ]
* tag 'staging-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (551 commits)
staging: vt6655: Remove filenames in files
staging: r8188eu: add extra TODO entries
staging: vt6656: Remove filenames in files
staging: wlan-ng: fix invalid assignment warning
staging: r8188eu: rename fields of struct rtl_ps
staging: r8188eu: remove ODM_DynamicPrimaryCCA_DupRTS()
staging: r8188eu: rename fields of struct dyn_primary_cca
staging: r8188eu: rename struct field Wifi_Error_Status
staging: r8188eu: Provide a TODO file for this driver
staging: r8188eu: remove unneeded variable
staging: r8188eu: remove unneeded conversions to bool
staging: r8188eu: remove {read,write}_macreg
staging: r8188eu: core: remove condition with no effect
staging: r8188eu: remove ethernet.h header file
staging: r8188eu: remove ip.h header file
staging: r8188eu: remove if_ether.h header file
staging: r8188eu: make rtw_deinit_intf_priv return void
staging: r8188eu: use is_multicast_ether_addr in os_dep/recv_linux.c
staging: r8188eu: use is_multicast_ether_addr in hal/rtl8188eu_xmit.c
staging: r8188eu: use is_multicast_ether_addr in core/rtw_xmit.c
...
Jonathan writes:
2nd set of new IIO device support and cleanups for the 5.15 cycle.
A small pull request to pick up a few new drivers and some cleanup
and fix patches.
New device support
* ad5110 non-volatile digital potentiometer
- New driver
* renesas rzl/gl2 12-bit / 8 channel ADC block
- New driver and bindings
Minor or late breaking fixes and cleanups
* ltc2983
- Fix a false assumption of initial interrupt during probe().
* hp03
- Use devm_* to simplify probe and allow the remove function to be dropped.
* rockchip_saradc
- Use a regulator notifier to reduce overheads of querying the scale.
* tag 'iio-for-5.15b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: Add driver for Renesas RZ/G2L A/D converter
dt-bindings: iio: adc: Add binding documentation for Renesas RZ/G2L A/D converter
iio: pressure: hp03: update device probe to register with devm functions
iio: adc: rockchip_saradc: add voltage notifier so get referenced voltage once at probe
iio: ltc2983: fix device probe
iio: potentiometer: Add driver support for AD5110
dt-bindings: iio: potentiometer: Add AD5110 in trivial-devices
