Based on mesa commit daa2ccff7a0201941db3901780d179e2634057d5
Small bit of .c churn in the phy code to adapt to split up of phy
related registers.
Signed-off-by: Rob Clark <robdclark@chromium.org>
A problem was reported on CoachZ devices where the display wouldn't come
up, or it would be distorted. It turns out that the PLL code here wasn't
getting called once dsi_pll_10nm_vco_recalc_rate() started returning the
same exact frequency, down to the Hz, that the bootloader was setting
instead of 0 when the clk was registered with the clk framework.
After commit 001d8dc338 ("drm/msm/dsi: remove temp data from global
pll structure") we use a hardcoded value for the parent clk frequency,
i.e. VCO_REF_CLK_RATE, and we also hardcode the value for FRAC_BITS,
instead of getting it from the config structure. This combination of
changes to the recalc function allows us to properly calculate the
frequency of the PLL regardless of whether or not the PLL has been
clk_prepare()d or clk_set_rate()d. That's a good improvement.
Unfortunately, this means that now we won't call down into the PLL clk
driver when we call clk_set_rate() because the frequency calculated in
the framework matches the frequency that is set in hardware. If the rate
is the same as what we want it should be OK to not call the set_rate PLL
op. The real problem is that the prepare op in this driver uses a
private struct member to stash away the vco frequency so that it can
call the set_rate op directly during prepare. Once the set_rate op is
never called because recalc_rate told us the rate is the same, we don't
set this private struct member before the prepare op runs, so we try to
call the set_rate function directly with a frequency of 0. This
effectively kills the PLL and configures it for a rate that won't work.
Calling set_rate from prepare is really quite bad and will confuse any
downstream clks about what the rate actually is of their parent. Fixing
that will be a rather large change though so we leave that to later.
For now, let's stash away the rate we calculate during recalc so that
the prepare op knows what frequency to set, instead of 0. This way
things keep working and the display can enable the PLL properly. In the
future, we should remove that code from the prepare op so that it
doesn't even try to call the set rate function.
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Fixes: 001d8dc338 ("drm/msm/dsi: remove temp data from global pll structure")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210608195519.125561-1-swboyd@chromium.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Implement phy_disable() callback to disable DSI PHY lanes and blocks
when phy is not used.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: ff73ff1940 ("drm/msm/dsi: Populate the 10nm PHY funcs")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Clang warns:
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: warning: logical not is
only applied to the left hand side of this bitwise operator
[-Wlogical-not-parentheses]
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^ ~
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: note: add parentheses
after the '!' to evaluate the bitwise operator first
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^
( )
drivers/gpu/drm/msm/dsi/phy/dsi_phy_10nm.c:80:6: note: add parentheses
around left hand side expression to silence this warning
if (!phy->cfg->quirks & V3_0_0_10NM_OLD_TIMINGS_QUIRK) {
^
( )
1 warning generated.
Add parentheses around the bitwise AND so it is evaluated first then
negated.
Fixes: 3dbbf8f09e ("drm/msm/dsi: Add old timings quirk for 10nm phy")
Link: https://github.com/ClangBuiltLinux/linux/issues/547
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The v3.0.0 10nm phy has two different implementations between MSM8998 and
SDM845, which require different timings calculations. Unfortunately, the
hardware designers did not choose to revise the version to account for this
delta so implement a quirk instead.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The MSM8998 dsi phy is 10nm v3.0.0 like SDM845, however there appear to
be minor differences such as the address space location.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use DRM_DEV_INFO/ERROR/WARN instead of dev_info/err/debug to generate
drm-formatted specific log messages so that it will be easy to
differentiate in case of multiple instances of driver.
Signed-off-by: Mamta Shukla <mamtashukla555@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the DSI PHY timings are hard-coded for a specific panel
for the 10nm PHY.
Replace this with the auto PHY timing calculator which can calculate
the PHY timings for any panel.
Changes in v4:
- None
Changes in v3:
- None
Changes in v2:
- None
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Populate the PHY ops with the downstream driver as reference.
There are a couple of TODOs which need to be resolved:
- The PHY timings are all hardcoded for now. This needs to be replaced
with automatic calculations once we get/understand them.
- There are some lane configuration registers which use a new
representation between physical and logical lane mappings. For now,
we've hardcoced them to follow the default mapping (i.e
logical 0 -> phy 0, logical 1 -> phy 1 etc).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add new 10nm DSI PLL/PHY files that will be used on SDM845.
Just populate empty pll/phy funcs for now. These will be filled up
later.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
