The DSI host might be left in some state by the bootloader. If this
state generates an IRQ, it might hang the system by holding the
interrupt line before the driver sets up the DSI host to the known
state.
Move the request_irq into msm_dsi_host_init and pass IRQF_NO_AUTOEN to
it. Call enable/disable_irq after msm_dsi_host_power_on/_off()
functions, so that we can be sure that the interrupt is delivered when
the host is in the known state.
It is not possible to defer the interrupt enablement to a later point,
because drm_panel_prepare might need to communicate with the panel over
the DSI link and that requires working interrupt.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211002010830.647416-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
During board bringups its useful to have a DSI test pattern
generator to isolate a DPU vs a DSI issue and focus on the relevant
hardware block.
To facilitate this, add an API which triggers the DSI controller
test pattern. The expected output is a rectangular checkered pattern.
This has been validated on a single DSI video mode panel by calling it
right after drm_panel_enable() which is also the ideal location to use
this as the DSI host and the panel have been initialized by then.
Further validation on dual DSI and command mode panel is pending.
If there are any fix ups needed for those, it shall be applied on top
of this change.
Changes in v2:
- generate the new dsi.xml.h and update the bitfield names
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/1626922232-29105-2-git-send-email-abhinavk@codeaurora.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Add the msm_disp_snapshot module which adds supports to dump dpu
registers and capture the drm atomic state which can be used in
case of error conditions.
changes in v5:
- start storing disp_state in msm_kms instead of dpu_kms
- get rid of MSM_DISP_SNAPSHOT_IN_* enum by simplifying the functions
- move snprintf inside the snapshot core by using varargs
- get rid of some stale code comments
- allow snapshot module for non-DPU targets
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1618606645-19695-3-git-send-email-abhinavk@codeaurora.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The only usage of dsi_host_ops is to assign its address to the ops field
in the mipi_dsi_host struct, which is a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, also create a label to put clkname.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
On SDM845 and SC7180 DSI needs to express a performance state
requirement on a power domain depending on the clock rates.
Use OPP table from DT to register with OPP framework and use
dev_pm_opp_set_rate() to set the clk/perf state.
dev_pm_opp_set_rate() is designed to be equivalent to clk_set_rate()
for devices without an OPP table, hence the change works fine
on devices/platforms which only need to set a clock rate.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
LANE_CTRL register in latest version of DSI controller (v2.2)
has additional functionality introduced to enable/disable HS
signalling with default value set to enabled. To accommodate this
change, LANE_CTRL register should be read and bit wise ORed to enable
non continuous clock mode. Without this change, if register is written
directly, HS signalling will be disabled resulting in black screen.
Changes in v1:
-Update LANE_CTRL register value
Changes in v2:
-Changing commit message accordingly.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Decouple enable and rate setting. Prep work to handle bootloader
enabled display.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
On msm8998, vblank timeouts are observed because the DSI controller is not
reset properly, which ends up stalling the MDP. This is because the reset
logic is not correct per the hardware documentation.
The documentation states that after asserting reset, software should wait
some time (no indication of how long), or poll the status register until it
returns 0 before deasserting reset.
wmb() is insufficient for this purpose since it just ensures ordering, not
timing between writes. Since asserting and deasserting reset occurs on the
same register, ordering is already guaranteed by the architecture, making
the wmb extraneous.
Since we would define a timeout for polling the status register to avoid a
possible infinite loop, lets just use a static delay of 20 ms, since 16.666
ms is the time available to process one frame at 60 fps.
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Cc: Hai Li <hali@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Sean Paul <sean@poorly.run>
[seanpaul renamed RESET_DELAY to DSI_RESET_TOGGLE_DELAY_MS]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011133939.16551-1-jeffrey.l.hugo@gmail.com
+ usual progress on cleanups
+ dsi vs EPROBE_DEFER fixes
+ msm8998 (snapdragon 835 support)
+ a540 gpu support (mesa support already landed)
+ dsi, dsi-phy support
+ mdp5 and dpu interconnect (bus/memory scaling) support
+ initial prep work for per-context pagetables (at least the parts that
don't have external dependencies like iommu/arm-smmu)
There is one more patch for fixing DSI cmd mode panels (part of a set of
patches to get things working on nexus5), but it would be conflicty with
1cff7440a8 in drm-next without rebasing or back-merge,
and since it doesn't conflict with anything in msm-next, I think it best
if Sean merges that through drm-mix-fixes instead.
(In other news, I've been making some progress w/ getting efifb working
properly on sdm850 laptop without horrible hacks, and drm/msm + clk stuff
not totally falling over when bootloader enables display and things are
already running when driver probes.. but not quite ready yet, hopefully
we can post some of that for 5.4.. should help for both the sdm835 and
sdm850 laptops.)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsj3N4XzDLSDoa+4RHZ9wXObYmhcep0M3LjnRg48BeLvg@mail.gmail.com
wait_for_completion_timeout() returns 0 on timeout and aleast 1 otherwise
so checking for < makes no sense here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode and ajusted_mode passed to the bridge .mode_set() operation
should never be modified by the bridge (and are not in any of the
existing bridge drivers). Make them const to make this clear.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
