There's no need to store all this stuff in intel_fbc_state_cache.
Just check it all against the plane/crtc states and store only
what we need. Probably more should get nuked still, but this
is a start.
So what we'll do is:
- each plane will check its own state and update its local
no_fbc_reason
- the per-plane no_fbc_reason (if any) then gets propagated
to the cache->no_fbc_reason while doing the actual update
- fbc->no_fbc_reason gets updated in the end with either
the value from the cache or directly from frontbuffer
tracking
It's still a bit messy, but should hopefuly get cleaned up
more in the future. At least now we can observe each plane's
reasons for rejecting FBC now more consistently, and we don't
have so mcuh redundant state store all over the place.
v2: store no_fbc_reason per-plane instead of per-pipe
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211124113652.22090-4-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Let's just stick to 32bit mmio accesses so we can get rid
of the bare "uncore" reg access in display code. The register
are defined as 32bit in the spec anyway.
We could define a 64bit "de" variant I suppose, but doesn't
really make much sense just for this one case, and when we
start to use the DSB for this stuff we'd also need another
64bit variant for that. Just easier to do 32bit always.
While at it we can reorder stuff a bit so that we write the
registers in order of increasing offset (more or less).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211201152552.7821-2-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
PLANE_CUS_CTL has a restriction of 4096 width even though
PLANE_SIZE and scaler size registers supports max 5120.
Take care of this restriction in max_width.
Without this patch, when 5k content is sent on HDR plane
with NV12 content, FIFO underrun is seen and screen blanks
out.
v2: Addressed review comments from Ville. Added separate
functions for max_width - for HDR and SDR
v3: Addressed review comments from Ville. Changed names of
HDR and SDR max_width functions to icl_hdr_plane_max_width
and icl_sdr_plane_max_width
v4: Fixed paranthesis alignment. No code change
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Vidya Srinivas <vidya.srinivas@intel.com>
[vsyrjala: Fix alignment]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211202110836.17536-1-vidya.srinivas@intel.com
drm/i915 feature pull for v5.17:
Features and functionality:
- Implement per-lane DP drive settings for ICL+ (Ville)
- Enable runtime pm autosuspend by default (Tilak Tangudu)
- ADL-P DSI support (Vandita)
- Add support for pipe C and D DMC firmware (Anusha)
- Implement (near)atomic gamma LUT updates via vblank workers (Ville)
- Split plane updates to noarm+arm phases (Ville)
- Remove the CCS FB stride restrictions on ADL-P (Imre)
- Add PSR selective fetch support for biplanar formats (Jouni)
- Add support for display audio codec keepalive (Kai)
- VRR platform support for display 11 (Manasi)
Refactoring and cleanups:
- FBC refactoring and cleanups preparing for multiple FBC instances (Ville)
- PCH modeset refactoring, move to its own file (Ville)
- Refactor and simplify handling of modifiers (Imre)
- PXP cleanups (Ville)
- Display header and include refactoring (Jani)
- Some register macro cleanups (Ville)
- Refactor DP HDMI DFP limit code (Ville)
Fixes:
- Disable DSB usage for now due to incorrect gamma LUT updates (Ville)
- Check async flip state of every crtc and plane only once (José)
- Fix DPT FB suspend/resume (Imre)
- Fix black screen on reboot due to disabled DP++ TMDS output buffers (Ville)
- Don't request GMBUS to generate irqs when called while irqs are off (Ville)
- Fix type1 DVI DP dual mode adapter heuristics for modern platforms (Ville)
- Fix fix integer overflow in 128b/132b data rate calculation (Jani)
- Fix bigjoiner state readout (Ville)
- Build fix for non-x86 (Siva)
- PSR fixes (José, Jouni, Ville)
- Disable ADL-P underrun recovery (José)
- Fix DP link parameter usage before valid DPCD (Imre)
- VRR vblank and frame counter fixes (Ville)
- Fix fastsets on TypeC ports following a non-blocking modeset (Imre)
- Compiler warning fixes (Nathan Chancellor)
- Fix DSI HS mode commands (William Tseng)
- Error return fixes (Dan Carpenter)
- Update memory bandwidth calculations (Radhakrishna)
- Implement WM0 cursor WA for DG2 (Stan)
- Fix DSI Double pixelclock on read-back for dual-link panels (Hans de Goede)
- HDMI 2.1 PCON FRL configuration fixes (Ankit)
Merges:
- DP link training delay helpers, via topic branch (Jani)
- Backmerge drm-next (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87v909it0t.fsf@intel.com
With asynchronous migrations, the vma state may be several migrations
ahead of the state that matches the request we're capturing.
Address that by introducing an i915_vma_snapshot structure that
can be used to snapshot relevant state at request submission.
In order to make sure we access the correct memory, the snapshots take
references on relevant sg-tables and memory regions.
Also move the capture list allocation out of the fence signaling
critical path and use the CONFIG_DRM_I915_CAPTURE_ERROR define to
avoid compiling in members and functions used for error capture
when they're not used.
Finally, Introduce lockdep annotation.
v4:
- Break out the capture allocation mode change to a separate patch.
v5:
- Fix compilation error in the !CONFIG_DRM_I915_CAPTURE_ERROR case
(kernel test robot)
v6:
- Use #if IS_ENABLED() instead of #ifdef to match driver style.
- Move yet another change of allocation mode to the separate patch.
- Commit message rework due to patch reordering.
v7:
- Adjust for removal of region refcounting.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211129202245.472043-1-thomas.hellstrom@linux.intel.com
While working on supporting the Intel HDR backlight interface, I noticed
that there's a couple of laptops that will very rarely manage to boot up
without detecting Intel HDR backlight support - even though it's supported
on the system. One example of such a laptop is the Lenovo P17 1st
generation.
Following some investigation Ville Syrjälä did through the docs they have
available to them, they discovered that there's actually supposed to be a
30ms wait after writing the source OUI before we begin setting up the rest
of the backlight interface.
This seems to be correct, as adding this 30ms delay seems to have
completely fixed the probing issues I was previously seeing. So - let's
start performing a 30ms wait after writing the OUI, which we do in a manner
similar to how we keep track of PPS delays (e.g. record the timestamp of
the OUI write, and then wait for however many ms are left since that
timestamp right before we interact with the backlight) in order to avoid
waiting any longer then we need to. As well, this also avoids us performing
this delay on systems where we don't end up using the HDR backlight
interface.
V3:
* Move last_oui_write into intel_dp
V2:
* Move panel delays into intel_pps
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Fixes: 4a8d79901d ("drm/i915/dp: Enable Intel's HDR backlight interface (only SDR for now)")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.12+
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211130212912.212044-1-lyude@redhat.com
(cherry picked from commit c7c90b0b84)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In igt_request_rewind(), mock_context(i915, "A") is assigned to ctx[0]
and used in i915_gem_context_get_engine(). There is a dereference
of ctx[0] in i915_gem_context_get_engine(), which could lead to a NULL
pointer dereference on failure of mock_context(i915, "A") .
So as mock_context(i915, "B").
Although this bug is not serious for it belongs to testing code, it is
better to be fixed to avoid unexpected failure in testing.
Fix this bugs by adding checks about ctx[0] and ctx[1].
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_DRM_I915_SELFTEST=y show no new warnings,
and our static analyzer no longer warns about this code.
References: 591c0fb85d ("drm/i915: Exercise request cancellation using a mock selftest")
[tursulin: Replaced fixes with references to avoid.]
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211130141545.153899-1-zhou1615@umn.edu
With both integrated and discrete Intel GPUs in a system, the current
global check of intel_iommu_gfx_mapped, as done from intel_vtd_active()
may not be completely accurate.
In this patch we add i915 parameter to intel_vtd_active() in order to
prepare it for multiple GPUs and we also change the check away from Intel
specific intel_iommu_gfx_mapped (global exported by the Intel IOMMU
driver) to probing the presence of IOMMU on a specific device using
device_iommu_mapped().
This will return true both for IOMMU pass-through and address translation
modes which matches the current behaviour. If in the future we wanted to
distinguish between these two modes we could either use
iommu_get_domain_for_dev() and check for __IOMMU_DOMAIN_PAGING bit
indicating address translation, or ask for a new API to be exported from
the IOMMU core code.
v2:
* Check for dmar translation specifically, not just iommu domain. (Baolu)
v3:
* Go back to plain "any domain" check for now, rewrite commit message.
v4:
* Use device_iommu_mapped. (Robin, Baolu)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211126141424.493753-1-tvrtko.ursulin@linux.intel.com
While working on supporting the Intel HDR backlight interface, I noticed
that there's a couple of laptops that will very rarely manage to boot up
without detecting Intel HDR backlight support - even though it's supported
on the system. One example of such a laptop is the Lenovo P17 1st
generation.
Following some investigation Ville Syrjälä did through the docs they have
available to them, they discovered that there's actually supposed to be a
30ms wait after writing the source OUI before we begin setting up the rest
of the backlight interface.
This seems to be correct, as adding this 30ms delay seems to have
completely fixed the probing issues I was previously seeing. So - let's
start performing a 30ms wait after writing the OUI, which we do in a manner
similar to how we keep track of PPS delays (e.g. record the timestamp of
the OUI write, and then wait for however many ms are left since that
timestamp right before we interact with the backlight) in order to avoid
waiting any longer then we need to. As well, this also avoids us performing
this delay on systems where we don't end up using the HDR backlight
interface.
V3:
* Move last_oui_write into intel_dp
V2:
* Move panel delays into intel_pps
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Fixes: 4a8d79901d ("drm/i915/dp: Enable Intel's HDR backlight interface (only SDR for now)")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.12+
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211130212912.212044-1-lyude@redhat.com
Rather than stealing bits from i915_sw_fence function pointer use
separate fields for function pointer and flags. If using two different
fields, the 4 byte alignment for the i915_sw_fence function pointer can
also be dropped.
v2:
(CI)
- Set new function field rather than flags in __i915_sw_fence_init
v3:
(Tvrtko)
- Remove BUG_ON(!fence->flags) in reinit as that will now blow up
- Only define fence->flags if CONFIG_DRM_I915_SW_FENCE_CHECK_DAG is
defined
v4:
- Rebase, resend for CI
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211116194929.10211-1-matthew.brost@intel.com
Since the PMU callback runs in irq context, it synchronizes with gt
reset using the reset count. We could run into a case where the PMU
callback could read the reset count before it is updated. This has a
potential of corrupting the busyness stats.
In addition to the reset count, check if the reset bit is set before
capturing busyness.
In addition save the previous stats only if you intend to update them.
v2:
- The 2 reset counts captured in the PMU callback can end up being the
same if they were captured right after the count is incremented in the
reset flow. This can lead to a bad busyness state. Ensure that reset
is not in progress when the initial reset count is captured.
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211108211057.68783-1-umesh.nerlige.ramappa@intel.com
This simply adds proper support for panel backlights that can be controlled
via VESA's backlight control protocol, but which also require that we
enable and disable the backlight via PWM instead of via the DPCD interface.
We also enable this by default, in order to fix some people's backlights
that were broken by not having this enabled.
For reference, backlights that require this and use VESA's backlight
interface tend to be laptops with hybrid GPUs, but this very well may
change in the future.
v4:
* Make sure that we call intel_backlight_level_to_pwm() in
intel_dp_aux_vesa_enable_backlight() - vsyrjala
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/3680
Fixes: fe7d52bcca ("drm/i915/dp: Don't use DPCD backlights that need PWM enable/disable")
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.12+
Link: https://patchwork.freedesktop.org/patch/msgid/20211105183342.130810-2-lyude@redhat.com
(cherry picked from commit 04f0d6cc62)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The "nomodeset" kernel cmdline parameter is handled by the vgacon driver
but the exported vgacon_text_force() symbol is only used by DRM drivers.
It makes much more sense for the parameter logic to be in the subsystem
of the drivers that are making use of it.
Let's move the vgacon_text_force() function and related logic to the DRM
subsystem. While doing that, rename it to drm_firmware_drivers_only() and
make it return true if "nomodeset" was used and false otherwise. This is
a better description of the condition that the drivers are testing for.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211112133230.1595307-4-javierm@redhat.com
The gpu coredump typically takes place in a dma_fence signalling
critical path, and hence can't use GFP_KERNEL allocations, as that
means we might hit deadlocks under memory pressure. However
changing to __GFP_KSWAPD_RECLAIM which will be done in an upcoming
patch will instead mean a lower chance of the allocation succeeding.
In particular large contigous allocations like the coredump page
vector.
Remove the page vector in favor of a linked list of single pages.
Use the page lru list head as the list link, as the page owner is
allowed to do that.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211108174547.979714-2-thomas.hellstrom@linux.intel.com
The signaled bit is already used for quick testing if a fence is signaled.
On top of that, it's a terrible abuse of dma-fence api, and in the common
case where the object is already locked by the caller, the trylock will fail.
If it were useful, the core dma-api would have exposed the same functionality.
The fact that i915 has a dma_resv_utils.c file should be a warning that the
functionality either belongs in core, or is not very useful at all.
In this case the latter.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
[mlankhorst: Improve commit message]
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211021103605.735002-3-maarten.lankhorst@linux.intel.com
Reviewed-by: Matthew Auld <matthew.auld@intel.com> #irc
Maarten requested a backmerge due his work depending on subtle semantic
changes introduced by:
7e2e69ed46 ("drm/i915: Fix i915_request fence wait semantics")
2cbb8d4d67 ("drm/i915: use new iterator in i915_gem_object_wait_reservation")
Both should probably have been merged to drm-intel-gt-next anyway.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't wait sync while migrating, but rather make the GPU blit await the
dependencies and add a moving fence to the object.
This also enables asynchronous VRAM management in that on eviction,
rather than waiting for the moving fence to expire before freeing VRAM,
it is freed immediately and the fence is stored with the VRAM manager and
handed out to newly allocated objects to await before clears and swapins,
or for kernel objects before setting up gpu vmas or mapping.
To collect dependencies before migrating, add a set of utilities that
coalesce these to a single dma_fence.
What is still missing for fully asynchronous operation is asynchronous vma
unbinding, which is still to be implemented.
This commit substantially reduces execution time in the gem_lmem_swapping
test.
v2:
- Make a couple of functions static.
v4:
- Fix some style issues (Matthew Auld)
- Audit and add more checks for ghost objects (Matthew Auld)
- Add more documentation for the i915_deps utility (Mattew Auld)
- Simplify the i915_deps_sync() function
v6:
- Re-check for fence signaled before returning -EBUSY (Matthew Auld)
- Use dma_resv_iter_is_exclusive() (Matthew Auld)
- Await all dma-resv fences before a migration blit (Matthew Auld)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211122214554.371864-6-thomas.hellstrom@linux.intel.com
With async migration, the shrinker may end up wanting to release the
pages of an object while the migration blit is still running, since
the GT migration code doesn't set up VMAs and the shrinker is thus
oblivious to the fact that the GPU is still using the pages.
Add waiting for gpu in the shrinker_release_pages() op and an
argument to that function indicating whether the shrinker expects it
to not wait for gpu. In the latter case the shrinker_release_pages()
op will return -EBUSY if the object is not idle.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211122214554.371864-5-thomas.hellstrom@linux.intel.com
There is an interesting refcounting loop:
struct intel_memory_region has a struct ttm_resource_manager,
ttm_resource_manager->move may hold a reference to i915_request,
i915_request may hold a reference to intel_context,
intel_context may hold a reference to drm_i915_gem_object,
drm_i915_gem_object may hold a reference to intel_memory_region.
Break this loop by dropping region reference counting.
In addition, Have regions with a manager moving fence make sure
that all region objects are released before freeing the region.
v6:
- Fix a code comment.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211122214554.371864-4-thomas.hellstrom@linux.intel.com
For now, we will only allow async migration when TTM is used,
so the paths we care about are related to TTM.
The mmap path is handled by having the fence in ttm_bo->moving,
when pinning, the binding only becomes available after the moving
fence is signaled, and pinning a cpu map will only work after
the moving fence signals.
This should close all holes where userspace can read a buffer
before it's fully migrated.
v2:
- Fix a couple of SPARSE warnings
v3:
- Fix a NULL pointer dereference
v4:
- Ditch the moving fence waiting for i915_vma_pin_iomap() and
replace with a verification that the vma is already bound.
(Matthew Auld)
- Squash with a previous patch introducing moving fence waiting and
accessing interfaces (Matthew Auld)
- Rename to indicated that we also add support for sync waiting.
v5:
- Fix check for NULL and unreferencing i915_vma_verify_bind_complete()
(Matthew Auld)
- Fix compilation failure if !CONFIG_DRM_I915_DEBUG_GEM
- Fix include ordering. (Matthew Auld)
v7:
- Fix yet another compilation failure with clang if
!CONFIG_DRM_I915_DEBUG_GEM
Co-developed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211122214554.371864-2-thomas.hellstrom@linux.intel.com
