PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder.
Bigjoiner is making life even more confusing by introducing
a N:1 relationship between pipes and transcoders. In that case
we only enable/configure the transcoder corresponding to the
master pipe. Let's do some renames to make it clear we're dealing
with the transcoder rather than pipe when it comes to
PIPECONF/TRANSCONF.
I decided to leave the _cpu_ part out from the function/macro
names since the PCH transcoder related stuff already has a
_pch_ in their name. So shouldn't be possible to confuse them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
On some Cherry Trail devices, DisplayPort over Type-C is supported through
a USB-PD microcontroller (e.g. a fusb302) + a mux to switch the superspeed
datalines between USB-3 and DP (e.g. a pi3usb30532). The kernel in this
case does the PD/alt-mode negotiation itself, rather then everything being
handled in firmware.
So the kernel itself picks an alt-mode, tells the Type-C "dongle" to switch
to DP mode and sets the mux accordingly. In this setup the HPD pin is not
connected, so the i915 driver needs to respond to a software event and scan
the DP port for changes manually.
This commit adds support for this. Together with the recent addition of
DP alt-mode support to the Type-C subsystem this makes DP over Type-C
work on these devices.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210817215201.795062-7-hdegoede@redhat.com
On Intel platforms we know that the ACPI connector device
node order will follow the order the driver (i915) decides.
The decision is made using the custom Intel ACPI OpRegion
(intel_opregion.c), though the driver does not actually know
that the values it sends to ACPI there are used for
associating a device node for the connectors, and assigning
address for them.
In reality that custom Intel ACPI OpRegion actually violates
ACPI specification (we supply dynamic information to objects
that are defined static, for example _ADR), however, it
makes assigning correct connector node for a connector entry
straightforward (it's one-on-one mapping).
Changes in v2 (Hans de goede):
- Take a reference on the fwnode which we assign to the connector,
for ACPI nodes this is a no-op but in the future we may see
software-fwnodes assigned to connectors which are ref-counted.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210817215201.795062-6-hdegoede@redhat.com
On some MST docking stations, rx_info can only be read after
RepeaterAuth_Send_ReceiverID_List and the RxStatus READY bit is set
otherwise the read will return -EIO.
This behavior causes the mst stream type1 capability test to fail to
read rx_info and determine if the topology supports type1 and fallback
to type0.
To fix this, check for type1 capability when we receive rx_info within
the AKE flow when we read RepeaterAuth_Send_ReceiverID_List instead
of an explicit read just for type1 capability checking.
This does require moving where we set stream_types to after
hdcp2_authenticate_sink() when we get rx_info but this occurs before we
do hdcp2_propagate_stream_management_info.
Also, legacy HDCP 2.0/2.1 are not type 1 capable either so check for
that as well.
Changes since v5:
- rename intel_set_stream_types() to intel_hdcp_prepare_streams()
(Anshuman)
Changes since v4:
- move topology_type1_capable to intel_digital_port and rename it as
hdcp_mst_type1_capable (Anshuman)
- make a helper function intel_set_stream_types() to set stream types
in hdcp2_authenticate_and_encrypt() (Anshuman)
- break on failure to set stream types and retry instead of returning
- remove no longer used declaration for streams_type1_capable()
Changes since v2:
- Remove no longer used variables in _intel_hdcp2_enable()
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-4-juston.li@intel.com
When reading RepeaterAuth_Send_ReceiverID_List, RxInfo is read by itself
once to retrieve the DEVICE_COUNT to calculate the size of the
ReceiverID list then read a second time as a part of reading ReceiverID
list.
On some MST docking stations, RxInfo can only be read after the RxStatus
READY bit is set otherwise the read will return -EIO. The spec states that
the READY bit should be cleared as soon as RxInfo has been read.
In this case, the first RxInfo read succeeds but after the READY bit is
cleared, the second read fails.
Fix it by reading RxInfo once and storing it before reading the rest of
RepeaterAuth_Send_ReceiverID_List once we know the size.
Modify get_receiver_id_list_size() to read and store RxInfo in the
message buffer and also parse DEVICE_COUNT so we know the size of
RepeaterAuth_Send_ReceiverID_List.
Afterwards, retrieve the rest of the message at the offset for
seq_num_V.
Changes in v5:
- Don't change the offset define for Send_ReceiverID_List
When reading, update message offset to account for RxInfo being read
Changes in v4:
- rebase and edit commit message
Changes in v3:
- remove comment
Changes in v2:
- remove unnecessary moving of drm_i915_private from patch 1
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-3-juston.li@intel.com
Update cp_irq_count_cached when reading messages rather than when
writing a message to make sure the value is up to date and not
stale from a previously handled CP_IRQ.
AKE flow doesn't always respond to a read with a ACK write msg.
E.g. AKE_Send_Pairing_Info will "timeout" because we received
a CP_IRQ for reading AKE_Send_H_Prime but no write occurred between that
and reading AKE_Send_Pairing_Info so cp_irq_count_cached is stale
causing the wait to return right away rather than waiting for a new
CP_IRQ.
Signed-off-by: Juston Li <juston.li@intel.com>
Acked-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-2-juston.li@intel.com
Frontbuffer rendering will be dropped for modern platforms but
before that we to prepare DRRS for it.
intel_drrs_flush and intel_drrs_invalidate will not be called
for platforms that will not support frontbuffer rendering so DRRS
needs another way to be notified about to page flips so it can change
between high and low refresh rates as needed.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210903221036.34770-3-jose.souza@intel.com
intel_dp_set_source_rates() calls intel_dp_is_edp(), which is unsafe to
use before intel_encoder->type is set. This causes incorrect max source
rate to be used for display 11+. On EHL and JSL, HBR3 is used instead of
HBR2, and on the other affected platforms, HBR2 is used instead of HBR3.
Move intel_dp_set_source_rates() to after intel_encoder->type is
set. Add comment to intel_dp_is_edp() describing unsafe usages. Cleanup
intel_dp_init_connector() while at it.
Note: The same change was originally added as commit 680c45c767
("drm/i915/dp: Correctly advertise HBR3 for GEN11+"), but later reverted
due to issues in CI in commit d391301960 ("Revert "drm/i915/dp:
Correctly advertise HBR3 for GEN11+"").
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901160402.24816-2-animesh.manna@intel.com
Pull drm updates from Dave Airlie:
"Highlights:
- i915 has seen a lot of refactoring and uAPI cleanups due to a
change in the upstream direction going forward
This has all been audited with known userspace, but there may be
some pitfalls that were missed.
- i915 now uses common TTM to enable discrete memory on DG1/2 GPUs
- i915 enables Jasper and Elkhart Lake by default and has preliminary
XeHP/DG2 support
- amdgpu adds support for Cyan Skillfish
- lots of implicit fencing rules documented and fixed up in drivers
- msm now uses the core scheduler
- the irq midlayer has been removed for non-legacy drivers
- the sysfb code now works on more than x86.
Otherwise the usual smattering of stuff everywhere, panels, bridges,
refactorings.
Detailed summary:
core:
- extract i915 eDP backlight into core
- DP aux bus support
- drm_device.irq_enabled removed
- port drivers to native irq interfaces
- export gem shadow plane handling for vgem
- print proper driver name in framebuffer registration
- driver fixes for implicit fencing rules
- ARM fixed rate compression modifier added
- updated fb damage handling
- rmfb ioctl logging/docs
- drop drm_gem_object_put_locked
- define DRM_FORMAT_MAX_PLANES
- add gem fb vmap/vunmap helpers
- add lockdep_assert(once) helpers
- mark drm irq midlayer as legacy
- use offset adjusted bo mapping conversion
vgaarb:
- cleanups
fbdev:
- extend efifb handling to all arches
- div by 0 fixes for multiple drivers
udmabuf:
- add hugepage mapping support
dma-buf:
- non-dynamic exporter fixups
- document implicit fencing rules
amdgpu:
- Initial Cyan Skillfish support
- switch virtual DCE over to vkms based atomic
- VCN/JPEG power down fixes
- NAVI PCIE link handling fixes
- AMD HDMI freesync fixes
- Yellow Carp + Beige Goby fixes
- Clockgating/S0ix/SMU/EEPROM fixes
- embed hw fence in job
- rework dma-resv handling
- ensure eviction to system ram
amdkfd:
- uapi: SVM address range query added
- sysfs leak fix
- GPUVM TLB optimizations
- vmfault/migration counters
i915:
- Enable JSL and EHL by default
- preliminary XeHP/DG2 support
- remove all CNL support (never shipped)
- move to TTM for discrete memory support
- allow mixed object mmap handling
- GEM uAPI spring cleaning
- add I915_MMAP_OBJECT_FIXED
- reinstate ADL-P mmap ioctls
- drop a bunch of unused by userspace features
- disable and remove GPU relocations
- revert some i915 misfeatures
- major refactoring of GuC for Gen11+
- execbuffer object locking separate step
- reject caching/set-domain on discrete
- Enable pipe DMC loading on XE-LPD and ADL-P
- add PSF GV point support
- Refactor and fix DDI buffer translations
- Clean up FBC CFB allocation code
- Finish INTEL_GEN() and friends macro conversions
nouveau:
- add eDP backlight support
- implicit fence fix
msm:
- a680/7c3 support
- drm/scheduler conversion
panfrost:
- rework GPU reset
virtio:
- fix fencing for planes
ast:
- add detect support
bochs:
- move to tiny GPU driver
vc4:
- use hotplug irqs
- HDMI codec support
vmwgfx:
- use internal vmware device headers
ingenic:
- demidlayering irq
rcar-du:
- shutdown fixes
- convert to bridge connector helpers
zynqmp-dsub:
- misc fixes
mgag200:
- convert PLL handling to atomic
mediatek:
- MT8133 AAL support
- gem mmap object support
- MT8167 support
etnaviv:
- NXP Layerscape LS1028A SoC support
- GEM mmap cleanups
tegra:
- new user API
exynos:
- missing unlock fix
- build warning fix
- use refcount_t"
* tag 'drm-next-2021-08-31-1' of git://anongit.freedesktop.org/drm/drm: (1318 commits)
drm/amd/display: Move AllowDRAMSelfRefreshOrDRAMClockChangeInVblank to bounding box
drm/amd/display: Remove duplicate dml init
drm/amd/display: Update bounding box states (v2)
drm/amd/display: Update number of DCN3 clock states
drm/amdgpu: disable GFX CGCG in aldebaran
drm/amdgpu: Clear RAS interrupt status on aldebaran
drm/amdgpu: Add support for RAS XGMI err query
drm/amdkfd: Account for SH/SE count when setting up cu masks.
drm/amdgpu: rename amdgpu_bo_get_preferred_pin_domain
drm/amdgpu: drop redundant cancel_delayed_work_sync call
drm/amdgpu: add missing cleanups for more ASICs on UVD/VCE suspend
drm/amdgpu: add missing cleanups for Polaris12 UVD/VCE on suspend
drm/amdkfd: map SVM range with correct access permission
drm/amdkfd: check access permisson to restore retry fault
drm/amdgpu: Update RAS XGMI Error Query
drm/amdgpu: Add driver infrastructure for MCA RAS
drm/amd/display: Add Logging for HDMI color depth information
drm/amd/amdgpu: consolidate PSP TA init shared buf functions
drm/amd/amdgpu: add name field back to ras_common_if
drm/amdgpu: Fix build with missing pm_suspend_target_state module export
...
