On VLV/CHV there is some kind of linkage between the cdclk frequency
and the DP link frequency. The spec says:
"For DP audio configuration, cdclk frequency shall be set to
meet the following requirements:
DP Link Frequency(MHz) | Cdclk frequency(MHz)
270 | 320 or higher
162 | 200 or higher"
I suspect that would more accurately be expressed as
"cdclk >= DP link clock", and in any case we can express it like
that in the code because of the limited set of cdclk (200, 266,
320, 400 MHz) and link frequencies (162 and 270 MHz) we support.
Without this we can end up in a situation where the cdclk
is too low and enabling DP audio will kill the pipe. Happens
eg. with 2560x1440 modes where the 266MHz cdclk is sufficient
to pump the pixels (241.5 MHz dotclock) but is too low for
the DP audio due to the link frequency being 270 MHz.
v2: Spell out the cdclk and link frequencies we actually support
Cc: stable@vger.kernel.org
Tested-by: Stefan Gottwald <gottwald@igel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111149
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717114536.22937-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit bffb31f73b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Gen2 doesn't have a frame counter and apparently we no longer provide
a fake .get_vblank_counter() hook for it. That means all tracepoints
calling that hook will oops. Update the tracepoints to use
intel_crtc_get_vblank_counter() which will gracefully fall back to
using the software counter. This is actually a better approach since
we now get (hopefully accurate) frame numbers in the traces.
This also gets rid of the raw driver->get_vblank_counter() calls, which
we need to do in order to switch to the per-crtc vblank vfuncs.
v2: Deal with new tracepoints
v3: Use a distinct variable name for the internal crtc iterator (Chris)
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 967dd48417 ("drm: remove drm_vblank_no_hw_counter assignment from driver code")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619170842.20579-2-ville.syrjala@linux.intel.com
(cherry picked from commit 4c888e7bd2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/gpu/drm/i915/gem/i915_gem_mman.c: In function ‘i915_gem_fault’:
drivers/gpu/drm/i915/gem/i915_gem_mman.c:342:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!i915_terminally_wedged(i915))
^
drivers/gpu/drm/i915/gem/i915_gem_mman.c:345:2: note: here
case -EAGAIN:
^~~~
drivers/gpu/drm/i915/gem/i915_gem_pages.c: In function ‘i915_gem_object_map’:
./include/linux/compiler.h:78:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:136:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/gpu/drm/i915/i915_utils.h:49:25: note: in expansion of macro ‘WARN’
#define MISSING_CASE(x) WARN(1, "Missing case (%s == %ld)\n", \
^~~~
drivers/gpu/drm/i915/gem/i915_gem_pages.c:270:3: note: in expansion of macro ‘MISSING_CASE’
MISSING_CASE(type);
^~~~~~~~~~~~
drivers/gpu/drm/i915/gem/i915_gem_pages.c:272:2: note: here
case I915_MAP_WB:
^~~~
drivers/gpu/drm/i915/i915_gpu_error.c: In function ‘error_record_engine_registers’:
./include/linux/compiler.h:78:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:136:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/gpu/drm/i915/i915_utils.h:49:25: note: in expansion of macro ‘WARN’
#define MISSING_CASE(x) WARN(1, "Missing case (%s == %ld)\n", \
^~~~
drivers/gpu/drm/i915/i915_gpu_error.c:1196:5: note: in expansion of macro ‘MISSING_CASE’
MISSING_CASE(engine->id);
^~~~~~~~~~~~
drivers/gpu/drm/i915/i915_gpu_error.c:1197:4: note: here
case RCS0:
^~~~
drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_get_fia_supported_lane_count’:
./include/linux/compiler.h:78:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:136:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/gpu/drm/i915/i915_utils.h:49:25: note: in expansion of macro ‘WARN’
#define MISSING_CASE(x) WARN(1, "Missing case (%s == %ld)\n", \
^~~~
drivers/gpu/drm/i915/display/intel_dp.c:233:3: note: in expansion of macro ‘MISSING_CASE’
MISSING_CASE(lane_info);
^~~~~~~~~~~~
drivers/gpu/drm/i915/display/intel_dp.c:234:2: note: here
case 1:
^~~~
drivers/gpu/drm/i915/display/intel_display.c: In function ‘check_digital_port_conflicts’:
CC [M] drivers/gpu/drm/nouveau/nvkm/engine/disp/cursgv100.o
drivers/gpu/drm/i915/display/intel_display.c:12043:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (WARN_ON(!HAS_DDI(to_i915(dev))))
^
drivers/gpu/drm/i915/display/intel_display.c:12046:3: note: here
case INTEL_OUTPUT_DP:
^~~~
Also, notice that the Makefile is modified to stop ignoring
fall-through warnings. The -Wimplicit-fallthrough option
will be enabled globally in v5.3.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
On VLV/CHV there is some kind of linkage between the cdclk frequency
and the DP link frequency. The spec says:
"For DP audio configuration, cdclk frequency shall be set to
meet the following requirements:
DP Link Frequency(MHz) | Cdclk frequency(MHz)
270 | 320 or higher
162 | 200 or higher"
I suspect that would more accurately be expressed as
"cdclk >= DP link clock", and in any case we can express it like
that in the code because of the limited set of cdclk (200, 266,
320, 400 MHz) and link frequencies (162 and 270 MHz) we support.
Without this we can end up in a situation where the cdclk
is too low and enabling DP audio will kill the pipe. Happens
eg. with 2560x1440 modes where the 266MHz cdclk is sufficient
to pump the pixels (241.5 MHz dotclock) but is too low for
the DP audio due to the link frequency being 270 MHz.
v2: Spell out the cdclk and link frequencies we actually support
Cc: stable@vger.kernel.org
Tested-by: Stefan Gottwald <gottwald@igel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111149
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190717114536.22937-1-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Right now we are aware of two cases that needs another hotplug retry:
- Unpowered type-c dongles
- HDMI slow unplug
Both have a complete explanation in the code to schedule another run
of the hotplug handler.
It could have more checks to just trigger the retry in those two
specific cases but why would sink signal a long pulse if there is
no change? Also the drawback of running the hotplug handler again
is really low and that could fix another cases that we are not
aware.
Also retrying for old DP ports(non-DDI) to make it consistent and not
cause CI failures if those systems are connected to chamelium boards
that will be used to simulate the issues reported in here.
v2: Also retrying for old DP ports(non-DDI)(Imre)
v4: Renamed INTEL_HOTPLUG_NOCHANGE to INTEL_HOTPLUG_UNCHANGED to keep
it consistent(Rodrigo)
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712005343.24571-2-jose.souza@intel.com
Some platforms may have Modular FIA. If Modular FIA is used in the SOC,
then Display Driver will access the additional instances of
FIA based on pre-assigned offset in GTTMADDR space.
Each Modular FIA instance has its own IOSF Sideband Port ID
and it houses only 2 Type-C Port. In SOC that has more than
two Type-C Ports, there are multiple instances of Modular FIA.
Gunit will need to use different destination ID when it access
different pair of Type-C Port.
The DFLEXDPSP register has Modular FIA bit starting on Tiger Lake. If
Modular FIA is used in the SOC, this register bit exists in all the
instances of Modular FIA. IOM FW is required to program only the MF bit
in first FIA instance that houses the Type-C Port 0 and Port 1, for
Display Driver to read from.
v2 (Lucas):
- Move all accesses to FIA to be contained in intel_tc.c, along with
display_fia that is now called tc_phy_fia
- Save the fia instance number on intel_digital_port, so we don't have
to query if modular FIA is used on every access
v3 (Lucas): Make function static
v4 (Lucas): Move enum phy_fia to the header and use it in
intel_digital_port (suggested by Ville)
v5 (Lucas): Add comment about the mapping between FIA and TC port
(suggested by Stuart)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712055706.12143-2-lucas.demarchi@intel.com
There are 2 new additional typeC ports in Tiger Lake and PORT-C is now a
combophy port. This results in 6 typeC ports and 3 combophy ports.
These 6 TC ports can be DP alternate mode, DP over thunderbolt, native
DP on legacy DP connector or native HDMI on legacy connector.
v2: Rebase on new modular FIA code (Lucas)
v3: Also add new port in port_identifier(), even though it can't
possibly be used there (requested by José)
v4: Add conversion port->tc_port in helper function after introction of
phy namespace (Lucas)
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-13-lucas.demarchi@intel.com
The patch adds the new power wells introduced by TGL (GEN 12) and
maps these to existing/new power domains. The changes for GEN 12 wrt
to GEN 11 are the following:
- Transcoder#EDP removed from power well#1 (Transcoder#A used in
low-power mode instead)
- Transcoder#A is now backed by power well#1 instead of power well#3
- The DDI#B/C combo PHY ports are now backed by power well#1 instead of
power well#3
- New power well#5 added for pipe#D functionality (TODO)
- 2 additional TC ports (TC#5-6) backed by power well#3, 2 port
specific IO power wells (only for the non-TBT modes) and 4 port
specific AUX power wells (2-2 for TBT vs. non-TBT modes)
- Power well#2 backs now VDSC/joining for pipe#A instead of VDSC for
eDP and MIPI DSI (TODO)
On TGL Port DDI#C changed to be a combo PHY (native DP/HDMI) and
BSpec has renamed ports DDI#D-F to TC#4-6 respectively. Thus on ICL we
have the following naming for ports:
- Combo PHYs (native DP/HDMI):
DDI#A-B
- TBT/non-TBT (TC altmode, native DP/HDMI) PHYs:
DDI#C-F
Starting from GEN 12 we have the following naming for ports:
- Combo PHYs (native DP/HDMI):
DDI#A-C
- TBT/non-TBT (TC altmode, native DP/HDMI) PHYs:
DDI TC#1-6
To save some space in the power domain enum the power domain naming in
the driver reflects the above change, that is power domains TC#1-3 are
added as aliases for DDI#D-F and new power domains are reserved for
TC#4-6.
v2 (Lucas):
- Separate out the bits and definitions for TGL from the ICL ones.
Fix use of TRANSCODER_EDP_VDSC, that is now the correct define since
we don't define TRANSCODER_A_VDSC power domain to spare a one bit in
the bitmask (suggested by Ville)
v3 (Lucas):
- Fix missing squashes on v2
- Rebase on renamed TRANSCODER_EDP_VDSC
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-9-lucas.demarchi@intel.com
