Move the *_get_ddi_pll() stuff into the encodet->get_config() hook.
There it neatly sits next to the matching .{enable,disable}_clock()
functions.
In order to avoid excessive boilerplate I changed the behaviour
such that all platforms now do the readout via
crtc_state->port_dpll[].
ICL+ TC is still a bit special due to TBTPLL not having a functional
.get_freq(). Should probably change that by adopting the LCPLL
approach, but that would require a fairly substantial rework of the
DPLL ID handling. So leave it for later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-5-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
All the other places we have use pipes instead of crtc indices
when tracking resource usage. Life is easier when we do it
the same way always, so switch the dpll mgr to using pipes as
well. Looks like it was actually mixing these up in some cases
so it would not even have worked correctly except when the
device has a contiguous set of pipes starting from pipe A.
Granted, that is the typical case but supposedly it may not
always hold on modern hw.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-4-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
For platforms/outputs without hardware frame counters we can't
call drm_crtc_accurate_vblank_count() when the vblank support is
disabled or we just get a WARN due to the crtc timings
(vblank->hwmode) being considered invalid. Note that until the
pipe in question has been enabled and drm_crtc_set_max_vblank_count()
has been called on it we would also take this path on platforms
which have a working frame counter. So getting the WARN is rather
likely on any platform unless you always boot with lots of displays
plugged in.
Also even on hardware with a working frame counter we may not be
able to read the actual frame counter register on disabled pipes
due the relevant power well being disabled. Ie. would just result
in the unclaimed reg spew.
So let's just avoid all this an directly report zero in case
the pipe is disabled.
Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210304170421.10901-3-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
On platforms/outputs without a working frame counter we rely
on the vblank code to cook up the frame counter from the timestamps.
That requires that vblank support is enabled. Thus we need to
move the pipe enable/disable tracepoints to the other side
of the drm_vblank_{on,off}() calls. There shouldn't really be
much happening between these old and new call sites so the
tracepoints should still provide reasonable data.
The alternative would be to give up on having the frame counter
values in the trace which would render the tracepoints more or
less pointless.
v2: Missed one case in intel_ddi_post_disable()
Drop the now useless i915_trace.h includes
Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210304170421.10901-2-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Populate conn_state->max_bpc with something sensible from the start.
Otherwise it's possible that we get to compute_sink_pipe_bpp() with
max_bpc==0.
The specific scenario goes as follows:
1. Initial connector state allocated with max_bpc==0
2. Trigger a modeset on the crtc feeding the connector, without
actually adding the connector to the commit
3. drm_atomic_connector_check() is skipped because the
connector has not yet been added, hence conn_state->max_bpc
retains its current value
4. drm_atomic_helper_check_modeset() ->
drm_atomic_add_affected_connectors() -> the connector
is now part of the commit
5. compute_baseline_pipe_bpp() -> MISSING_CASE(max_bpc==0)
Note that pipe_bpp itself may not be populated on pre-g4x machines,
in which case we just fall back to max_bpc==8 and let .compute_config()
limit the resulting pipe_bpp further if necessary.
Cc: Daniel Vetter <daniel@ffwll.ch>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210216160035.4780-1-ville.syrjala@linux.intel.com
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Pull more drm updates from Dave Airlie:
"This is mostly fixes but I missed msm-next pull last week. It's been
in drm-next.
Otherwise it's a selection of i915, amdgpu and misc fixes, one TTM
memory leak, nothing really major stands out otherwise.
core:
- vblank fence timing improvements
dma-buf:
- improve error handling
ttm:
- memory leak fix
msm:
- a6xx speedbin support
- a508, a509, a512 support
- various a5xx fixes
- various dpu fixes
- qseed3lite support for sm8250
- dsi fix for msm8994
- mdp5 fix for framerate bug with cmd mode panels
- a6xx GMU OOB race fixes that were showing up in CI
- various addition and removal of semicolons
- gem submit fix for legacy userspace relocs path
amdgpu:
- clang warning fix
- S0ix platform shutdown/poweroff fix
- misc display fixes
i915:
- color format fix
- -Wuninitialised reenabled
- GVT ww locking, cmd parser fixes
atyfb:
- fix build
rockchip:
- AFBC modifier fix"
* tag 'drm-next-2021-02-26' of git://anongit.freedesktop.org/drm/drm: (60 commits)
drm/panel: kd35t133: allow using non-continuous dsi clock
drm/rockchip: Require the YTR modifier for AFBC
drm/ttm: Fix a memory leak
drm/drm_vblank: set the dma-fence timestamp during send_vblank_event
dma-fence: allow signaling drivers to set fence timestamp
dma-buf: heaps: Rework heap allocation hooks to return struct dma_buf instead of fd
dma-buf: system_heap: Make sure to return an error if we abort
drm/amd/display: Fix system hang after multiple hotplugs (v3)
drm/amdgpu: fix shutdown and poweroff process failed with s0ix
drm/i915: Nuke INTEL_OUTPUT_FORMAT_INVALID
drm/i915: Enable -Wuninitialized
drm/amd/display: Remove Assert from dcn10_get_dig_frontend
drm/amd/display: Add vupdate_no_lock interrupts for DCN2.1
Revert "drm/amd/display: reuse current context instead of recreating one"
drm/amd/pm/swsmu: Avoid using structure_size uninitialized in smu_cmn_init_soft_gpu_metrics
fbdev: atyfb: add stubs for aty_{ld,st}_lcd()
drm/i915/gvt: Introduce per object locking in GVT scheduler.
drm/i915/gvt: Purge dev_priv->gt
drm/i915/gvt: Parse default state to update reg whitelist
dt-bindings: dp-connector: Drop maxItems from -supply
...
In Bspec the TGL TypeC ports are TC1-6, the AUX power well request flags
are USBC1-6/TBT1-6, so for clarity use these names in the port power
domain names instead of the D-I terminology (which Bspec uses only for
the ICL TypeC ports).
A domain name should follow the <domain>_<pipe/transcoder/port/aux_ch>
format. Add the new aliases based on this, leaving a change to rename
all the rest accordingly for a follow-up.
No functional change.
v2: Add comment to commit log about unifying domain names. (Jose)
Cc: Souza Jose <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222210400.940158-1-imre.deak@intel.com
Even though GEN12+ HW supports PSR + DC3CO, DMC's HW DC3CO exit mechanism
has an issue with using of Selective Fecth and PSR2 manual tracking.
And as some GEN12+ platforms (RKL, ADL-S) don't support PSR2 HW tracking,
Selective Fetch will be enabled by default on that platforms.
Therefore if the system enables PSR Selective Fetch / PSR manual tracking,
it does not allow DC3CO dc state, in that case.
When this DC3CO exit issue is addressed while PSR Selective Fetch is
enabled, this restriction should be removed.
v2: Address Jose's review comment.
- Fix typo
- Move check routine of DC3CO ability to
tgl_dc3co_exitline_compute_config()
v3: Change the check routine of enablement of psr2 sel fetch. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222213006.1609085-1-gwan-gyeong.mun@intel.com
We tend to use output_format!=RGB as a shorthand for YCbCr, but
this fails if we have a disabled crtc where output_format==INVALID.
We're now getting some fail from intel_color_check() when we have:
hw.enable==false
hw.ctm!=NULL
output_format==INVALID
Let's avoid that by throwing INTEL_OUTPUT_FORMAT_INVALID to the
dumpster, and thus everything defaults to RGB when the crtc
is disabled.
This does beg the deeper question of how much of the state
should we in fact be validating when hw/uapi.enable==false.
And should we even be doing the uapi->hw copy when
uapi.enable==false? So far I've not been able to come up with
satisfactory answers for myself, so I'm putting it off for the
moment.
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: 0aa5c3835c ("drm/i915: support two CSC module on gen11 and later")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2964
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205202322.27608-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
(cherry picked from commit 7e07c68f06)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There is no support for two pipes one transcoder for PSR and if we had
that the current code should not use cpu_transcoder.
Also I can't see a scenario where crtc_state->enable_psr2_sel_fetch is
set and PSR is not enabled and if by a bug it happens PSR HW will just
ignore any value in set in PSR2_MAN_TRK_CTL.
So dropping all the rest and keeping the same behavior that we have
with intel_psr2_program_plane_sel_fetch().
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209181439.215104-2-jose.souza@intel.com
We tend to use output_format!=RGB as a shorthand for YCbCr, but
this fails if we have a disabled crtc where output_format==INVALID.
We're now getting some fail from intel_color_check() when we have:
hw.enable==false
hw.ctm!=NULL
output_format==INVALID
Let's avoid that by throwing INTEL_OUTPUT_FORMAT_INVALID to the
dumpster, and thus everything defaults to RGB when the crtc
is disabled.
This does beg the deeper question of how much of the state
should we in fact be validating when hw/uapi.enable==false.
And should we even be doing the uapi->hw copy when
uapi.enable==false? So far I've not been able to come up with
satisfactory answers for myself, so I'm putting it off for the
moment.
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: 0aa5c3835c ("drm/i915: support two CSC module on gen11 and later")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2964
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205202322.27608-1-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
ilk+ planes get notably unhappy when the plane x+w exceeds
the stride. This wasn't a problem previously because we
always aligned SURF to the closest tile boundary so the
x offset never got particularly large. But now with async
flips we have to align to 256KiB instead and thus this
becomes a real issue.
On ilk/snb/ivb it looks like the accesses just wrap
early to the next tile row when scanout goes past the
SURF+n*stride boundary, hsw/bdw suffer more heavily and
start to underrun constantly. i965/g4x appear to be immune.
vlv/chv I've not yet checked.
Let's borrow another trick from the skl+ code and search
backwards for a better SURF offset in the hopes of getting the
x offset below the limit. IIRC when I ran into a similar issue
on skl years ago it was causing the hardware to fall over
pretty hard as well.
And let's be consistent and include i965/g4x in the check
as well, just in case I just got super lucky somehow when
I wasn't able to reproduce the issue. Not that it really
matters since we still use 4k SURF alignment for i965/g4x
anyway.
Fixes: 6ede6b0616 ("drm/i915: Implement async flips for vlv/chv")
Fixes: 4bb18054ad ("drm/i915: Implement async flip for ilk/snb")
Fixes: 2a636e240c ("drm/i915: Implement async flip for ivb/hsw")
Fixes: cda195f13a ("drm/i915: Implement async flips for bdw")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210209021918.16234-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 59fb8218c8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
[Rodrigo also exported some functions from intel_display.c during backport]
Instead of every new platform having yet another masive
copy of the whole PLL sanitation code, let's just reuse the
.disable_clock() hook for this purpose. We do need to plug
this into the ICL+ DSI code for that, but fortunately it
already has a suitable function we can use.
We do lose the debug message though on account of not bothering
to check if the clock is actually enabled or not before turning
it off. We could introduce yet another vfunc to query the current
state, but not sure it's worth the hassle?
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-14-ville.syrjala@linux.intel.com
For ICL+ we have several styles of clock routing for DDIs:
1) TC DDI + TC PHY
-> needs DDI_CLK_SEL==MG/TBT part form intel_ddi_clk_{select,disable}()
and ICL_DPCLKA_CFGCR0_TC_CLK_OFF part form icl_{map,unmap}_plls_to_ports()
2) ICL/TGL combo DDI + combo PHY
-> just need the stuff from icl_{map,unmap}_plls_to_ports()
3) JSL/EHL TC DDI + combo PHY
-> needs DDI_CLK_SEL==MG part from intel_ddi_clk_{select,disable}() and
the full combo style clock selection from icl_{map,unmap}_plls_to_ports()
4) ADLS/RKL
-> these use both TC and combo DDIs with combo PHYs, however they
always use the full combo style clock selection as per
icl_{map,unmap}_plls_to_ports() and do not use DDI_CLK_SEL at all,
thus get treated the same as 2)
We extract all that from the current mess in the following way:
1) icl_ddi_tc_{enable,disable}_clock()
2) icl_ddi_combo_{enable,disable}_clock()
3) jsl_ddi_tc_{enable,disable}_clock()
4) for now we reuse icl_ddi_combo_{enable,disable}_clock() here
v2: s/dev_priv/i915/ (Lucas)
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-8-ville.syrjala@linux.intel.com
