drm-misc and drm-intel pull request for topic/i915-ttm:
- Convert i915 lmem handling to ttm.
- Add a patch to temporarily add a driver_private member to vma_node.
- Use this to allow mixed object mmap handling for i915.
Currently as the workaround is applied the screen flickers. As a result
we do not achieve seamless boot experience.
Avoiding the issue in the common use-case might be hard, although we can
resolve it for dual GPU setups - when the "other" GPU is primary and/or
outputs are connected to it.
With this I was able to get seamless experience on my Intel/Nvidia box,
running systemd-boot and sddm/Xorg. Note that the i915 driver is within
initrd while the Nvidia one is not.
Without this patch, the splash presented by systemd-boot (UEFI BGRT) is
torn down as the code-path kicks in, leaving the monitor blank until the
login manager starts.
Same issue were reported with plymouth/grub, although personally I
wasn't able to get them to behave on my setup.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210604154905.660142-1-emil.l.velikov@gmail.com
Since we're about to implement eDP backlight support in nouveau using the
standard protocol from VESA, we might as well just take the code that's
already written for this and move it into a set of shared DRM helpers.
Note that these helpers are intended to handle DPCD related backlight
control bits such as setting the brightness level over AUX, probing the
backlight's TCON, enabling/disabling the backlight over AUX if supported,
etc. Any PWM-related portions of backlight control are explicitly left up
to the driver, as these will vary from platform to platform.
The only exception to this is the calculation of the PWM frequency
pre-divider value. This is because the only platform-specific information
required for this is the PWM frequency of the panel, which the driver is
expected to provide if available. The actual algorithm for calculating this
value is standard and is defined in the eDP specification from VESA.
Note that these helpers do not yet implement the full range of features
the VESA backlight interface provides, and only provide the following
functionality (all of which was already present in i915's DPCD backlight
support):
* Basic control of brightness levels
* Basic probing of backlight capabilities
* Helpers for enabling and disabling the backlight
v3:
* Split out changes to i915's backlight code to separate patches to make it
easier to review
v4:
* Style/spelling changes from Thomas Zimmermann
v5:
* Start using new drm_dbg_*() functions
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: greg.depoire@gmail.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514181504.565252-9-lyude@redhat.com
Since we're about to be moving this code into shared DRM helpers, we might
as well start to cache certain backlight capabilities that can be
determined from the EDP DPCD, and are likely to be relevant to the majority
of drivers using said helpers. The main purpose of this is just to prevent
every driver from having to check everything against the eDP DPCD using DP
macros, which makes the code slightly easier to read (especially since the
names of some of the eDP capabilities don't exactly match up with what we
actually need to use them for, like DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT
for instance).
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514181504.565252-5-lyude@redhat.com
This is kind of an annoying aspect of DRM's DP helpers:
drm_dp_dpcd_readb/writeb() return the size of bytes read/written on
success, thus we want to check against that instead of checking if the
return value is less than 0.
I'll probably be fixing this in the near future once I start doing DP work
again, also because I'd rather not mix a tree-wide refactor like that in
with a patch series intended to be around introducing DP backlight helpers.
So, for now let's just handle the return values from each function
correctly.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514181504.565252-3-lyude@redhat.com
Noticed this while moving all of the VESA backlight code in i915 over to
DRM helpers: it would appear that we calculate the frequency value we want
to write to DP_EDP_BACKLIGHT_FREQ_SET twice even though this value never
actually changes during runtime. So, let's simplify things by just caching
this value in intel_panel.backlight, and re-writing it as-needed.
Changes since v1:
* Wrap panel->backlight.edp.vesa.pwm_freq_pre_divider in
DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP check - Jani
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Dave Airlie <airlied@gmail.com>
Cc: greg.depoire@gmail.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514181504.565252-2-lyude@redhat.com
This introduces the following function that can exit and activate a psr
source when intel_psr is already enabled.
- intel_psr_pause(): Pause current PSR. It deactivates current psr state.
- intel_psr_resume(): Resume paused PSR. It activates paused psr state.
v2: Address Jose's review comment.
- Remove unneeded changes around the intel_psr_enable().
- Add intel_psr_post_exit() which processes waiting until PSR is idle
and WA for SelectiveFetch.
v3: Address Jose's review comment.
- Rename intel_psr_post_exit() to intel_psr_wait_exit_locked().
- Move WA_1408330847 to intel_psr_disable_locked()
- If the PSR is paused by an explicit intel_psr_paused() call, make the
intel_psr_flush() not to activate PSR.
v4: Address Jose's review comment.
- In order to avoid the scenario of PSR is not active but there is a
scheduled psr->work, it changes the check routine of intel_psr_pause()
for PSR's enablement from "psr->active" to "psr->enable".
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210608085415.515342-1-gwan-gyeong.mun@intel.com
Commit 78b772e1a0 ("drm/i915/display: Fill PSR state during hardware
configuration read out") is not allowing fastsets to happen when PSR
states changes but PSR is a feature that can be enabled and disabled
during fastsets.
So here moving the PSR pipe conf checks to a block that is only
executed when checking if HW state matches with requested state, not
during the phase where it checks if fastset is possible or not.
There still a state mismatch not allowing fastsets between states
turning off or on PSR because of crtc_state->infoframes.enable
BIT(DP_SDP_VSC) but at least for now it will allow a fastset between
PSR1 <-> PSR2, that is a case heavilly used by CI due to pipe CRC not
work with PSR2, but the remaning issue will be fixed in a future patch.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 78b772e1a0 ("drm/i915/display: Fill PSR state during hardware configuration read out")
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514232247.144542-1-jose.souza@intel.com
UAPI Changes:
- Add reworked uAPI for DG1 behind CONFIG_BROKEN (Matt A, Abdiel)
Driver Changes:
- Fix for Gitlab issues #3293 and #3450:
Avoid kernel crash on older L-shape memory machines
- Add Wa_14010733141 (VDBox SFC reset) for Gen11+ (Aditya)
- Fix crash in auto_retire active retire callback due to
misalignment (Stephane)
- Fix overlay active retire callback alignment (Tvrtko)
- Eliminate need to align active retire callbacks (Matt A, Ville,
Daniel)
- Program FF_MODE2 tuning value for all Gen12 platforms (Caz)
- Add Wa_14011060649 for TGL,RKL,DG1 and ADLS (Swathi)
- Create stolen memory region from local memory on DG1 (CQ)
- Place PD in LMEM on dGFX (Matt A)
- Use WC when default state object is allocated in LMEM (Venkata)
- Determine the coherent map type based on object location (Venkata)
- Use lmem physical addresses for fb_mmap() on discrete (Mohammed)
- Bypass aperture on fbdev when LMEM is available (Anusha)
- Return error value when displayable BO not in LMEM for dGFX (Mohammed)
- Do release kernel context if breadcrumb measure fails (Janusz)
- Hide modparams for compiled-out features (Tvrtko)
- Apply Wa_22010271021 for all Gen11 platforms (Caz)
- Fix unlikely ref count race in arming the watchdog timer (Tvrtko)
- Check actual RC6 enable status in PMU (Tvrtko)
- Fix a double free in gen8_preallocate_top_level_pdp (Lv)
- Use trylock in shrinker for GGTT on BSW VT-d and BXT (Maarten)
- Remove erroneous i915_is_ggtt check for
I915_GEM_OBJECT_UNBIND_VM_TRYLOCK (Maarten)
- Convert uAPI headers to real kerneldoc (Matt A)
- Clean up kerneldoc warnings headers (Matt A, Maarten)
- Fail driver if LMEM training failed (Matt R)
- Avoid div-by-zero on Gen2 (Ville)
- Read C0DRB3/C1DRB3 as 16 bits again and add _BW suffix (Ville)
- Remove reference to struct drm_device.pdev (Thomas)
- Increase separation between GuC and execlists code (Chris, Matt B)
- Use might_alloc() (Bernard)
- Split DGFX_FEATURES from GEN12_FEATURES (Lucas)
- Deduplicate Wa_22010271021 programming on (Jose)
- Drop duplicate WaDisable4x2SubspanOptimization:hsw (Tvrtko)
- Selftest improvements (Chris, Hsin-Yi, Tvrtko)
- Shuffle around init_memory_region for stolen (Matt)
- Typo fixes (wengjianfeng)
[airlied: fix conflict with fixes in i915_active.c]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YLCbBR22BsQ/dpJB@jlahtine-mobl.ger.corp.intel.com
[why]
Link rate in kHz is what is eventually required to calculate the link
bandwidth, which makes kHz a more generic unit. This should also make
forward-compatibility with new DP standards easier.
[how]
- Replace 'link rate DPCD code' with 'link rate in kHz' when used with
drm_dp_mst_topology_mgr_init()
- Add/remove related DPCD code conversion from/to kHz where applicable
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512210011.8425-2-nikola.cornij@amd.com
The kernel prefers enabling fbc over the initial fb, since this leads to
actual runtime power savings, so if the initial fb is deemed too big
using some heuristic, then we simply skip allocating stolen for it.
However if the kernel is not configured with fbcon then it should be
possible to relax this, since unlike with fbcon the display server
shouldn't preserve it when later replacing it, and so we should be able
to re-use the stolen memory for fbc and friends. This patch is reported
to fix some flicker seen during boot splash on some devices.
v2: s/FRAMEBUFFER_CONSOLE/CONFIG_FRAMEBUFFER_CONSOLE
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210526124901.245689-1-matthew.auld@intel.com
XE_LPD brings enhanced underrun recovery: the hardware can somewhat
mitigate underruns by using an interpolated replacement pixel (soft
underrun) or the previous pixel (hard underrun). Furthermore, underruns
can now be caused downstream by the port, even if the pipe itself is
operating properly. The interrupt register and PIPE_STATUS register
give us extra bits to recognize hard/soft underruns and determine
whether the underrun was caused by the port, so we'll use that
information to print some more descriptive errors when underruns occur.
v2:
- Keep ICL's PIPE_STATUS defined separately from the old GMCH pipe
status register. (Ville)
- Only read/clear the PIPE_STATUS register on platforms with
display ver >= 11. (Lucas)
v3:
- Actually enable+unmask all the new underrun interrupts, clear stale
bits out from PIPE_STATUS before enabling the interrupts, report all
FIFO underruns errors at once, rename a bunch of stuff to unconfuse
vs. PIPESTAT. (Ville)
Bspec: 50335
Bspec: 50366
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210526000656.3060314-2-matthew.d.roper@intel.com
