Source needs to write DPCD 103-106 after receiving a PHY request to change
swing/pre-emphasis after reading DPCD 206-207. This is especially needed if
there is a retimer between source and sink and the retimer implements AUX_CH
interception scheme to manage DP PHY settings (e.g. adjusting Swing/Pre-emphasis
equalization level) for DP output channel. If the source doesn't write to
DPCD 103-106, the retimer may not output the requested swing/pre-emphasis and
eventually we fail compliance.
v2: Rebase and use crtc->lane_count (Imre)
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210226081554.984307-1-khaled.almahallawy@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
This workaround is specific for a particular panel on Google
chromebook project. When user space daemon enter idle state.
It request adjust brightness to 0, turn backlight_enable signal
off and keep eDP main link active.
On general LCD, this behavior might not be a problem.
But on this panel, its tcon would expect source to execute
full eDP power off sequence after drop backlight_enable signal.
Without eDP power off sequence. Even source try to turn
backlight_enable signal on and restore proper brightness level.
This panel is not able to light on again.
This WA ignored the request from user space daemon to disable
backlight_enable signal and keep it on always. When user space
request kernel to turn eDP display off, kernel driver still
can control backlight_enable signal properly. It would not
impact standard eDP power off sequence.
v2: 1. modify the quirk name and debug messages.
2. unregister backlight.power callback for specific device.
v3: 1. modify debug output messages.
2. use DMI_EXACT_MATCH instead of DMI_MATCH.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210624053932.21037-1-shawn.c.lee@intel.com
intel_dp_check_mst_status() uses a 14-byte array to read the DPRX Event
Status Indicator data, but then passes that buffer at offset 10 off as
an argument to drm_dp_channel_eq_ok().
End result: there are only 4 bytes remaining of the buffer, yet
drm_dp_channel_eq_ok() wants a 6-byte buffer. gcc-11 correctly warns
about this case:
drivers/gpu/drm/i915/display/intel_dp.c: In function ‘intel_dp_check_mst_status’:
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: warning: ‘drm_dp_channel_eq_ok’ reading 6 bytes from a region of size 4 [-Wstringop-overread]
3491 | !drm_dp_channel_eq_ok(&esi[10], intel_dp->lane_count)) {
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/i915/display/intel_dp.c:3491:22: note: referencing argument 1 of type ‘const u8 *’ {aka ‘const unsigned char *’}
In file included from drivers/gpu/drm/i915/display/intel_dp.c:38:
include/drm/drm_dp_helper.h:1466:6: note: in a call to function ‘drm_dp_channel_eq_ok’
1466 | bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
| ^~~~~~~~~~~~~~~~~~~~
6:14 elapsed
This commit just extends the original array by 2 zero-initialized bytes,
avoiding the warning.
There may be some underlying bug in here that caused this confusion, but
this is at least no worse than the existing situation that could use
random data off the stack.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
Gen to ver conversions across the driver
The main change is Lucas' series [1], with Ville's GLK fixes [2] and a
cherry-pick of Matt's commit [3] from drm-intel-next as a base to avoid
conflicts.
[1] https://patchwork.freedesktop.org/series/88825/
[2] https://patchwork.freedesktop.org/series/88938/
[3] 70bfb30743 ("drm/i915/display: Eliminate IS_GEN9_{BC,LP}")
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
# Conflicts:
# drivers/gpu/drm/i915/display/intel_bios.c
# drivers/gpu/drm/i915/display/intel_cdclk.c
# drivers/gpu/drm/i915/display/intel_ddi.c
# drivers/gpu/drm/i915/display/intel_ddi_buf_trans.c
# drivers/gpu/drm/i915/display/intel_display.c
# drivers/gpu/drm/i915/display/intel_display_power.c
# drivers/gpu/drm/i915/display/intel_dp.c
# drivers/gpu/drm/i915/display/intel_dpll_mgr.c
# drivers/gpu/drm/i915/display/intel_fbc.c
# drivers/gpu/drm/i915/display/intel_gmbus.c
# drivers/gpu/drm/i915/display/intel_hdcp.c
# drivers/gpu/drm/i915/display/intel_hdmi.c
# drivers/gpu/drm/i915/display/intel_pps.c
# drivers/gpu/drm/i915/intel_pm.c
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/878s5ebny0.fsf@intel.com
While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:
1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?
2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check
With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.
So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:
@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1
@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1
@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com
Display features should not be initialized or de-initialized when there
is no display. Skip modeset initialization, output setup, plane, crtc,
encoder, connector registration, display cdclk and rawclk
initialization, display core initialization, etc.
Skip the functionality at as high level as possible, and remove any
redundant checks. If the functionality is conditional to *other* display
checks, do not add more. If the un-initialization has checks for
initialization, do not add more.
We explicitly do not care about any GMCH/VLV/CHV code paths, as they've
always had and will have display.
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210408203150.237947-3-jose.souza@intel.com
Currently the FRL training mode (Concurrent, Sequential) and
training type (Normal, Extended) are not defined properly and
are passed as bool values in drm_helpers for pcon
configuration for FRL training.
This patch:
-Add register masks for Sequential and Normal FRL training options.
-Fixes the drm_helpers for FRL Training configuration to use the
appropriate masks.
-Modifies the calls to the above drm_helpers in i915/intel_dp as per
the above change.
v2: Re-used the register masks for these options, instead of enum. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210323112422.1211-2-ankit.k.nautiyal@intel.com
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
ILK is the only platform that we consider "gen5" and SNB is the only
platform we consider "gen6." Add an IS_SANDYBRIDGE() macro and then
replace numeric platform tests for these two generations with direct
platform tests with the following Coccinelle semantic patch:
@@ expression dev_priv; @@
- IS_GEN(dev_priv, 5)
+ IS_IRONLAKE(dev_priv)
@@ expression dev_priv; @@
- IS_GEN(dev_priv, 6)
+ IS_SANDYBRIDGE(dev_priv)
@@ expression dev_priv; @@
- IS_GEN_RANGE(dev_priv, 5, 6)
+ IS_IRONLAKE(dev_priv) || IS_SANDYBRIDGE(dev_priv)
This will simplify our upcoming patches which eliminate INTEL_GEN()
usage in the display code.
v2:
- Reverse ilk/snb order for IS_GEN_RANGE conversion. (Ville)
- Rebase + regenerate from semantic patch
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-2-matthew.d.roper@intel.com
