Collect the dipslay related mask under the display sub-structure
in intel_device_info.
Note that there is a slight change in behaviour in that we zero
out .display entirely when !HAS_DISPLAY (aka. pipe_mask==0), so
now we also zero out the other masks (although cpu_transocder_mask
should already be zero of pipe_mask is zero). abox_mask is
only used by the display core init when HAS_DISPLAY is true, so
the actual behaviour of the system shouldn't change despite the
zeroing of these masks.
There is a lot more display stuff directly in device info that
could be moved over. Maybe someone else will be inspired to do it...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211210122726.12577-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
MIPI DSI transcoder cannot be in video mode to support any of the
display C states.
Bspec: 49195 (For DC*co DSI transcoders cannot be in video mode)
Bspec: 49193 (Hardware does not support DC5 or DC6 with MIPI DSI enabled)
Bspec: 49188 (desc of DSI_DCSTATE_CTL talks about cmd mode PM control
v2: Align to the power domain ordering (Jani)
Add bspec references (Imre)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211019151435.20477-4-vandita.kulkarni@intel.com
DG1 and XE_PLD platforms has Audio MMIO/VERBS lies in PG0 power
well. Adjusting the power domain accordingly to
POWER_DOMAIN_AUDIO_MMIO for audio detection and
POWER_DOMAIN_AUDIO_PLAYBACK for audio playback.
While doing this it requires to use POWER_DOMAIN_AUDIO_MMIO
power domain instead of POWER_DOMAIN_AUDIO in crtc power domain mask
and POWER_DOMAIN_AUDIO_PLAYBACK with intel_display_power_{get, put}
to enable/disable display audio codec power.
It will save the power in use cases when DP/HDMI connectors
configured with PIPE_A without any audio playback.
v1: Changes since RFC
- changed power domain names. [Imre]
- Removed TC{3,6}, AUX_USBC{3,6} and TBT from DG1
power well and PW_3 power domains. [Imre]
- Fixed the order of powe wells , power domains and its
registration. [Imre]
v2:
- Not allowe DC states when AUDIO_MMIO domain enabled. [Imre]
v3:
- Squashes the commits of series to avoid build failure.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
[Fix typo in commit message and in AUDIO_PLAYBACK domain name]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210729121858.16897-2-anshuman.gupta@intel.com
Workarounds are documented in the bspec with an exclusive upper bound
(i.e., a "fixed" stepping that no longer needs the workaround). This
makes our driver's use of an inclusive upper bound for stepping ranges
confusing; the differing notation between code and bspec makes it very
easy for mistakes to creep in.
Let's switch the upper bound of our IS_{GT,DISP}_STEP macros over to use
an exclusive upper bound like the bspec does. This also has the benefit
of helping make sure workarounds are properly handled for new minor
steppings that show up (e.g., an A1 between the A0 and B0 we already
knew about) --- if the new intermediate stepping pulls in hardware fixes
early, there will be an update to the workaround definition which lets
us know we need to change our code. If the new stepping does not pull a
hardware fix earlier, then the new stepping will already be captured
properly by the "[begin, fix)" range in the code.
We'll probably need to be extra vigilant in code review of new
workarounds for the near future to make sure developers notice the new
semantics of workaround bounds. But we just migrated a bunch of our
platforms from the IS_REVID bounds over to IS_{GT,DISP}_STEP, so people
are already adjusting to the new macros and now is a good time to make
this change too.
[mattrope: Split out display changes to apply through intel-next tree]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210717051426.4120328-8-matthew.d.roper@intel.com
The switch from old old IS_FOO_REVID() macros to the new table-based
IS_FOO_{GT,DISP}_STEP() macros is needed on both drm-intel-next (for
display-based DMC matching) and drm-intel-gt-next (for workaround
guards). To avoid conflicts, we'll apply the patches to a topic branch
and merge it to both intel branches to ensure the transition to the
new macros is clean.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
This patch adds Pipe A plumbing to the already
existing parsing and loading functions which is
taken care of in the prep patches. Adding MAX_DMC_FW
to keep track for both Main and Pipe A DMC while loading
the respective blobs.
Also adding present field in dmc_info.
s/find_dmc_fw_offset/csr_set_dmc_fw_offset. While at it add
fw_info_matches_stepping() helper. CSR_PROGRAM() should now
take the starting address of the particular blob (Main or Pipe)
and not hardcode it.
v2: Add dmc_offset and start_mmioaddr fields for dmc_info struct.
v3: Add a missing corner cases of stepping-substepping combination in
fw_info_matches_stepping() helper.
v4: Add macro for start_mmioaddr for V1 package. Simplify code
in dmc_set_fw_offset (Lucas)
Cc: Souza, Jose <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210621191415.29823-3-anusha.srivatsa@intel.com
On ADL-P TC cold is exited and blocked when legacy aux is powered,
that is exacly the same of what ICL need for static TC ports.
TODO: When a TBT hub or monitor is connected it will cause TBT and
legacy aux to be powered at the same time, hopefully this will not
cause any issues but if it do, some rework will be needed.
v2:
- skip icl_tc_port_assert_ref_held() warn on, adl-p uses aux to
block TC cold
v3:
- Drop icl_tc_port_assert_ref_held() earlier return for adl_p, not
needed anymore
- Set timeout_expected when enabling aux power well as port could be
disconnected when tc_cold_block() is called
BSpec: 55480
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210524214805.259692-2-jose.souza@intel.com
Aside from the hardware-managed PG0, XE_LPD has power wells 1-2 and
A-D. These power wells should be enabled/disabled according to the
following dependency tree (enable top to bottom, disable bottom to top):
PG0
|
--PG1--
/ \
PGA --PG2--
/ | \
PGB PGC PGD
PWR_WELL_CTL follows the general ICL/TGL design and places PG A-D in the
bits that would have been PG 6-9 under the old scheme.
PWR_WELL_CTL_{DDI,AUX}'s bit indexing for DDI's A-C and TC1 is the same
as TGL, but DDI-D is placed at index 7 (bits 14 & 15).
v2:
- Squash in LPSP status patch from Uma since it's also a
powerwell-specific change.
Bspec: 49233
Bspec: 49503
Bspec: 49504
Bspec: 49505
Bspec: 49296
Bspec: 50090
Bspec: 53920
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512042144.2089071-4-matthew.d.roper@intel.com
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
Gen to ver conversions across the driver
The main change is Lucas' series [1], with Ville's GLK fixes [2] and a
cherry-pick of Matt's commit [3] from drm-intel-next as a base to avoid
conflicts.
[1] https://patchwork.freedesktop.org/series/88825/
[2] https://patchwork.freedesktop.org/series/88938/
[3] 70bfb30743 ("drm/i915/display: Eliminate IS_GEN9_{BC,LP}")
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
# Conflicts:
# drivers/gpu/drm/i915/display/intel_bios.c
# drivers/gpu/drm/i915/display/intel_cdclk.c
# drivers/gpu/drm/i915/display/intel_ddi.c
# drivers/gpu/drm/i915/display/intel_ddi_buf_trans.c
# drivers/gpu/drm/i915/display/intel_display.c
# drivers/gpu/drm/i915/display/intel_display_power.c
# drivers/gpu/drm/i915/display/intel_dp.c
# drivers/gpu/drm/i915/display/intel_dpll_mgr.c
# drivers/gpu/drm/i915/display/intel_fbc.c
# drivers/gpu/drm/i915/display/intel_gmbus.c
# drivers/gpu/drm/i915/display/intel_hdcp.c
# drivers/gpu/drm/i915/display/intel_hdmi.c
# drivers/gpu/drm/i915/display/intel_pps.c
# drivers/gpu/drm/i915/intel_pm.c
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/878s5ebny0.fsf@intel.com
While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:
1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?
2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check
With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.
So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:
@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1
@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1
@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com
Display features should not be initialized or de-initialized when there
is no display. Skip modeset initialization, output setup, plane, crtc,
encoder, connector registration, display cdclk and rawclk
initialization, display core initialization, etc.
Skip the functionality at as high level as possible, and remove any
redundant checks. If the functionality is conditional to *other* display
checks, do not add more. If the un-initialization has checks for
initialization, do not add more.
We explicitly do not care about any GMCH/VLV/CHV code paths, as they've
always had and will have display.
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210408203150.237947-3-jose.souza@intel.com
