Prior to commit 6c836d965b ("drm/rockchip: Use the helpers for PSR"),
"PSR exit" used non-blocking analogix_dp_send_psr_spd(). The refactor
started using the blocking variant, for a variety of reasons -- quoting
Sean Paul's potentially-faulty memory:
"""
- To avoid racing a subsequent PSR entry (if exit takes a long time)
- To avoid racing disable/modeset
- We're not displaying new content while exiting PSR anyways, so there
is minimal utility in allowing frames to be submitted
- We're lying to userspace telling them frames are on the screen when
we're just dropping them on the floor
"""
However, I'm finding that this blocking transition is causing upwards of
60+ ms of unneeded latency on PSR-exit, to the point that initial cursor
movements when leaving PSR are unbearably jumpy.
It turns out that we need to meet in the middle somewhere: Sean is right
that we were "lying to userspace" with a non-blocking PSR-exit, but the
new blocking behavior is also waiting too long:
According to the eDP specification, the sink device must support PSR
entry transitions from both state 4 (ACTIVE_RESYNC) and state 0
(INACTIVE). It also states that in ACTIVE_RESYNC, "the Sink device must
display the incoming active frames from the Source device with no
visible glitches and/or artifacts."
Thus, for our purposes, we only need to wait for ACTIVE_RESYNC before
moving on; we are ready to display video, and subsequent PSR-entry is
safe.
Tested on a Samsung Chromebook Plus (i.e., Rockchip RK3399 Gru Kevin),
where this saves about 60ms of latency, for PSR-exit that used to
take about 80ms.
Fixes: 6c836d965b ("drm/rockchip: Use the helpers for PSR")
Cc: <stable@vger.kernel.org>
Cc: Zain Wang <wzz@rock-chips.com>
Cc: Tomasz Figa <tfiga@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211103135112.v3.1.I67612ea073c3306c71b46a87be894f79707082df@changeid
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VSC SDP Payload for PSR is one of data block type of SDP (Secondaray Data
Packet). In order to generalize SDP packet structure name, it renames
struct edp_vsc_psr to struct dp_sdp. And each SDP data blocks have
different usages, each SDP type has different reserved data blocks and
Video_Stream_Configuration Extension VESA SDP might use all of Data Blocks
as Extended INFORFRAME Data Byte. so it makes Data Block variables as
array type. And it adds comments of details of DB of VSC SDP Payload
for Pixel Encoding/Colorimetry Format. This comments follows DP 1.4a spec,
section 2.2.5.7.5, chapter "VSC SDP Payload for Pixel Encoding/Colorimetry
Format".
v7: Addressed review comments from Ville.
v9: Rename a member value name DB to db on struct dp_sdp [Laurent]
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190521121721.32010-3-gwan-gyeong.mun@intel.com
Reference from drm_dp_aux description (about transfer):
Upon success, the implementation should return the number of payload bytes
that were transferred, or a negative error-code on failure. Helpers
propagate errors from the .transfer() function, with the exception of
the -EBUSY error, which causes a transaction to be retried. On a short,
helpers will return -EPROTO to make it simpler to check for failure.
The analogix_dp_transfer will return num_transferred, but if there is none
byte been transferred, the return value will be 0, which means success, we
should return error-code if transfer none byte.
for (retry = 0; retry < 32; retry++) {
err = aux->transfer(aux, &msg);
if (err < 0) {
if (err == -EBUSY)
continue;
goto unlock;
}
}
Cc: zain wang <wzz@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1479255219-7243-1-git-send-email-jay.xu@rock-chips.com
The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
sense to save the power consumption.
This patch have exported two symbols for platform driver to implement
the PSR function in hardware side:
- analogix_dp_active_psr()
- analogix_dp_inactive_psr()
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
As vendor document indicate, when REF_CLK bit set 0, then DP
phy's REF_CLK should switch to 24M source clock.
But due to IC PHY layout mistaken, some chips need to flip this
bit(like RK3288), and unfortunately they didn't indicate in the
DP version register. That's why we have to make this little hack.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
It may caused a dead lock if we flush the hpd work in bridge disable time.
The normal flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
3. HPD work already in idle, no need to run the work function.
OUT <-- analogix_dp_bridge
OUT <-- DRM IOCTL
The dead lock flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
IN --> analogix_dp_hotplug
IN --> drm_helper_hpd_irq_event
3. Acquire mode_config lock (This lock already have been acquired in previous step 1)
** Dead Lock Now **
It's wrong to flush the hpd work in bridge->disable time, I guess the
original code just want to ensure the delay work must be finish before
encoder disabled.
The flush work in bridge disable time is try to ensure the HPD event
won't be missed before display card disabled, actually we can take a
fast respond way(interrupt thread) to update DRM HPD event to fix the
delay update and possible dead lock.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Some edp screen do not have hpd signal, so we can't just return
failed when hpd plug in detect failed.
This is an hardware property, so we need add a devicetree property
"analogix,need-force-hpd" to indicate this sutiation.
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Both hsync/vsync polarity and interlace mode can be parsed from
drm display mode, and dynamic_range and ycbcr_coeff can be judge
by the video code.
But presumably Exynos still relies on the DT properties, so take
good use of mode_fixup() in to achieve the compatibility hacks.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
link_rate and lane_count already configured in analogix_dp_set_link_train(),
so we don't need to config those repeatly after training finished, just
remove them out.
Beside Display Port 1.2 already support 5.4Gbps link rate, the maximum sets
would change from {1.62Gbps, 2.7Gbps} to {1.62Gbps, 2.7Gbps, 5.4Gbps}.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
In the original split we kept the register constants intact to keep the
diff small. Still the constants are Analogix-specific, so rename them now.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Split the dp core driver from exynos directory to bridge directory,
and rename the core driver to analogix_dp_*, rename the platform
code to exynos_dp.
Beside the new analogix_dp driver would export six hooks.
"analogix_dp_bind()" and "analogix_dp_unbind()"
"analogix_dp_suspned()" and "analogix_dp_resume()"
"analogix_dp_detect()" and "analogix_dp_get_modes()"
The bind/unbind symbols is used for analogix platform driver to connect
with analogix_dp core driver. And the detect/get_modes is used for analogix
platform driver to init the connector.
They reason why connector need register in helper driver is rockchip drm
haven't implement the atomic API, but Exynos drm have implement it, so
there would need two different connector helper functions, that's why we
leave the connector register in helper driver.
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
