[Why]
DIB_BE_CNTL<i>.DIG_HPD_SELECT selects the HPD block being used
by the display endpoint assigned to DIG<i>. In the case of USB4
display endpoints, no physical HPD block is assigned.
[How]
Setting DIB_BE_CNTL<i>.DIG_HPD_SELECT to 5 indicates that no HPD
is assigned to a display endpoint. Firmware decrements the
HPD_SELECT value by 1 before writing it to the register.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To process SET_CONFIG transactions with DMUB using inbox1 and
outbox1 mail boxes.
[How]
1) DMUB posts SET_CONFIG reply as an Outbox1 message of type
DMUB_OUT_CMD__SET_CONFIG_REPLY.
2) The dmub async to sync mechanism for AUX is modified to accommodate
SET_CONFIG commands for both command issue and reply code paths.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jude Shih <shenshih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To process SET_CONFIG transactions with DMUB using inbox1 and
outbox1 mail boxes.
[How]
1) Added inbox1 DPIA command subtype DMUB_CMD__DPIA_SET_CONFIG_ACCESS to
issue SET_CONFIG command to DMUB in dc_process_dmub_set_config_async().
DMUB processes the command with DPIA sends reply back immediately or
in an outbox1 message triggering an outbox1 interrupt to driver.
2) DMUB posts SET_CONFIG reply as an Outbox1 message of type
DMUB_OUT_CMD__SET_CONFIG_REPLY.
3) The dmub async to sync mechanism for AUX is modified to accommodate
SET_CONFIG commands for both command issue and reply code paths.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Training settings need to be applied to DPIA link at start of each
training loop. Note: FEC readiness should be configured before link
training while FEC enablement should be configured once training is
complete.
[How]
- Implement DPIA link configuration function.
- Account for dynamically assigned link encoders during link
configuration.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Training of DPIA link differs enough from that of conventional
DP link to warrant a separate implementation.
[How]
- Implement top-level of DPIA training loop.
- Make functions shared between DP and DPIA link training "public".
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To add support for HPD & HPD RX interrupt handling for USB4 DPIA in
YELLOW_CARP_B0. USB4 DPIA HPD & HPD RX interrupts are issued from DMUB to
driver as a outbox1 message.
[HOW]
1) Created get_link_index_from_dpia_port_index() to retrieve link index
from dpia port index for HPD & HPD RX dmub notifications.
2) Added DMUB HPD & HPD RX handling in dmub_srv_stat_get_notification().
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To enable dc links for USB4 DPIA ports and AUX command tunneling
for YELLOW_CARP_B0.
[HOW]
1) Created dc links for all USB4 DPIA ports in create_links().
dc_link_construct() implementation is split for legacy DDC and DPIAs.
As usb4 has no ddc, ddc->ddc_pin will be set to NULL for its dc link
and this parameter will be used to identify the dc links as DPIA. The
dc link for DPIA is further to be enhanced with implementation for link
encoder and link initialization.
2) usb4_dpia_count in struct resource_pool will be initialized to 4 in
dcn31_resource_construct() if the DCN is YELLOW_CARP_B0.
3) Enabled DMUB AUX via outbox for YELLOW_CARP_B0.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During DQE's promotion test, error appears in dmesg at boot
on dcn3.1;
[How]
Add NULL pointor check for the pointor to the amdgpu_dm_connector;
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Trying to enable multiple displays simultaneously exposed shortcomings
with the algorithm for dynamic link encoder assignment.
The main problems were:
- Assuming stream order remained constant across states would
sometimes lead to invalid DIG encoder assignment.
- Incorrect logic for deciding whether or not a DIG could support a
stream would also sometimes lead to invalid DIG encoder assignment.
- Changes in encoder assignment were wholesale while updating of the
pipe backend is incremental. This would lead to the hardware state
not matching the software state even with valid encoder assignments.
[How]
The following changes fix the identified problems.
- Use stream pointer rather than stream index to track streams across
states.
- Fix DIG compatibility check by examining the link signal type
rather than the stream signal type.
- Modify assignment algorithm to make incremental updates so software
and hardware states remain coherent.
Additionally:
- Add assertions and an encoder assignment validation
function link_enc_cfg_validate() to detect potential problems with
encoder assignment closer to their root cause.
- Reduce the frequency with which the assignment algorithm is
executed. It should not be necessary for fast state validation.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The codes to blank all dp display have been called many times,
so add a helper in dc_link to make it more concise.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- New firmware version
- Fix DMUB problems on stress test.
- Improve link training by skip overrride for preferred link
- Refinement of FPU code structure for DCN2
- Fix 3DLUT skipped programming
- Fix detection of 4 lane for DPALT
- Fix dcn3 failure due to dmcbu_abm not created
- Limit display scaling to up to 4k for DCN 3.1
- Add helper for blanking all dp displays
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current FPU code for DCN2x is located under dml/dcn2x.
This is not aligned with DC's general source tree
structure.
[How]
Move FPU code for DCN2x to dml/dcn20.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Overriding link setting inside override_training_settings
result in fallback link settings being ignored. This can
potentially cause link training to always fail and consequently
result in an infinite loop of link training to occur in
dp_verify_link_cap during detection.
[How]
Since preferred link settings are already considered inside
decide_link_settings, skip the check in override_training_settings
to avoid infinite link training loops.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some reason we're defining DP 2.0 definitions inside our
driver. Now that patches to introduce relevant definitions
are slated to be merged into drm-next this is causing conflicts.
In file included from drivers/gpu/drm/amd/amdgpu/amdgpu_bo_list.c:33:
In file included from ./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgpu.h:70:
In file included from ./drivers/gpu/drm/amd/amdgpu/../amdgpu/amdgpu_mode.h:36:
./include/drm/drm_dp_helper.h:1322:9: error: 'DP_MAIN_LINK_CHANNEL_CODING_PHY_REPEATER' macro redefined [-Werror,-Wmacro-redefined]
^
./drivers/gpu/drm/amd/amdgpu/../display/dc/dc_dp_types.h:881:9: note: previous definition is here
^
1 error generated.
[How]
Guard all display driver defines with #ifndef for now. Once we pull
in the new definitions into amd-staging-drm-next we will follow
up and drop definitions from our driver and provide follow-up
header updates for any addition DP 2.0 definitions required
by our driver.
We also ensure drm_dp_helper.h is included before dc_dp_types.h.
v3: Ensure drm_dp_helper.h is included before dc_dp_types.h
v2: Add one missing endif
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The two AMD drivers have their own custom offsetof() implementation
that now triggers a warning with recent versions of clang:
drivers/gpu/drm/radeon/radeon_atombios.c:133:14: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
Change all the instances to use the normal offsetof() provided
by the kernel that does not have this problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recently debugging efforts have involved setting/checking the
X.Y value used during payload allocation. Current output for
Y was calculated with incorrect bitshift. Y value is also not
human readable.
[How]
Refactor logging into separate function. Fix Y calculation error
and format output to be human readable.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is a chance verified link cap can be greater than max link cap.
This causes software hang because we cannot power up PHY with link rate
that cannot handle.
The change is to guard verfieid link cap from becoming larger than max link cap
our PHy can support.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Blnd, 3dlut, and shaper LUT select registers are double buffered, however
their accompanying LUT memory shutdown registers are not. As a result,
shutting down LUT memory immediately after setting a block to bypass causes
corruption as bypass only happens at next Vupdate.
[HOW]
Re-enable mem low power for CM block
Force optimization on next flip and disable LUT memory during optimization
sequence if LUT select field is then set to bypass
v2: squash in CONFIG_DRM_AMD_DC_DCN fix (Alex)
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ASSR is dependent on Signed PSP Verstage to enable Content
Protection for eDP panels. Unsigned PSP verstage is used
during development phase causing ASSR to FAIL.
As a result, link training is performed with
DP_PANEL_MODE_DEFAULT instead of DP_PANEL_MODE_EDP for
eDP panels that causes display flicker on some panels.
[How]
- Do not change panel mode, if ASSR is disabled
- Just report and continue to perform eDP link training
with right settings further.
Signed-off-by: Praful Swarnakar <Praful.Swarnakar@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This version brings along following fixes:
- Fixes to backlight, LUT, PPS, MST
- Use correct vpg for 128b/132b encoding
- Improved logging for VCP
- Replace referral of dal with dc
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change is needed for DCN2 to make use of the immediate_update
flag. With this flag, update to PPS will be immediate, rather than
always taking place on dig_update signal.
[How]
Set AFMT_GENERIC7_FRAME/IMMEDIATE_UPDATE bits depending on flag
value.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Ilya <Ilya.Bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MST streams share the same link and should share the same encoder.
The current availability check may erroneously determine that an
encoder is unavailable for MST streams.
[How]
When checking for link encoder availability, check if an encoder
in use shares a link with the stream for which the availability
check is being conducted. If the link is shared, then the link
encoder should be shared too and will be deemed available.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Requested feature to assist with Thermal, Acoustic, Power, and
Performance tuning.
[How]
Add a debug field that will override calculated minimum DRAM clock,
if the debug value is larger than the calculate value.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prevent unnecessary wake up of DMCUB when ABM is enabled without PSR
enabled, driver will notify DMCUB to stop ABM's vertical interrupts
if vsync is disabled and steady state is reached.
[How]
Send inbox message to notify ABM pause based on vsync on/off
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
