A similar check was added in gpiochip_generic_request, but not in free.
This has caused an imbalance count of request vs. free calls to the
pinctrl driver. This patch is targeted to fix that issue.
Fixes: 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
Signed-off-by: Edmond Chung <edmondchung@google.com>
Signed-off-by: Andrew Chant <achant@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
pm_runtime_enable will increase power disable depth. Thus a
pairing decrement is needed on the error handling path to keep
it balanced.
Fixes:27a49ed17e224(gpio: arizona: Add support for GPIOs that)
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Liang <zhengliang6@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The gpiochip may have dependencies from pinmux and so got deferred. Now it
will print error message every time -EPROBE_DEFER is returned which is
unnecessary:
"gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517"
Hence, do suppress error message for -EPROBE_DEFER case.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by explicitly adding a fallthrough pseudo-keyword to indicate
that the code is intended to fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The gpiochip_add_data() may return -EPROBE_DEFER which is not handled
properly by TI GPIO driver and causes unnecessary boot log messages.
Hence, add proper deferred probe handling with new dev_err_probe() API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no matching spi_get_drvdata() call in the driver, so there is no
need to do spi_set_drvdata(). This looks like it probably was copied from a
driver that used both spi_set_drvdata() & spi_get_drvdata().
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In dwapb_get_reset(), if devm_reset_control_get_optional_shared() fails,
an error message is printed even if the failure is the benign
EPROBE_DEFER error due to the reset controller not yet being
initialized. Use dev_err_probe() to handle
devm_reset_control_get_optional_shared() errors to avoid unnecessarilly
printing an error message for the deferred probe error.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We can simplify the error path in probe() and drop remove() entirely if
we provide a devm action for freeing the device ID.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We can simplify the code in gpio-exar by using regmap. This allows us to
drop the mutex (regmap provides its own locking) and we can also reuse
regmap's bit operations instead of implementing our own update function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Provide and use helpers for calculating the register address and bit
offset instead of hand coding it in every function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It's more elegant to use a helper local variable to store the address
of the underlying struct device than to dereference pdev everywhere. It
also has the benefit of avoiding unnecessary line breaks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We don't need to specify any ranges when allocating IDs so we can switch
to ida_alloc() and ida_free() instead of the ida_simple_ counterparts.
ida_simple_get(ida, 0, 0, gfp) is equivalent to
ida_alloc_range(ida, 0, UINT_MAX, gfp) which is equivalent to
ida_alloc(ida, gfp). Note: IDR will never actually allocate an ID
larger than INT_MAX.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We can get hwirq number of the gpio by its irq_data->hwirq so that we don't
need to add more macros for different platforms. This patch is tested in
SiFive Unleashed board and SiFive Unmatched board.
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
GpioIo() resources don't contain an initial value for the output pin.
Therefore instead of deducting its value solely based on bias field
we should deduce that value from the polarity and the bias fields.
Typical scenario is, when pin is defined in the table and its polarity,
specified in _DSD or via platform code, is defined as active low,
in the following call chain:
-> acpi_populate_gpio_lookup()
-> acpi_gpio_to_gpiod_flags()
it will return GPIOD_OUT_HIGH if bias is set no matter if polarity
is GPIO_ACTIVE_LOW, so it will return the current level instead of
the logical level.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Vasile-Laurentiu Stanimir <vasile-laurentiu.stanimir@windriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In some cases the GpioInt() resource is coming with bias settings
which may affect system functioning. Respect bias settings for
GpioInt() resource by calling acpi_gpio_update_gpiod_*flags() API
in acpi_dev_gpio_irq_get().
Reported-by: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If all we want to manage is a single pointer, there's no need to
manually allocate and add a new devres. We can simply use
devm_add_action_or_reset() and shrink the code by a good bit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
gpio fixes for v5.10-rc3
- fix missing conversion to gpiolib irqchip in gpio-dwapb
- fix bank properties for ast2600 variant in gpio-aspeed
- make sysfs work again when the character device is disabled
- fix interrupt handling in gpio-pcie-idio-24
Use raw_spinlock in order to fix spurious messages about invalid context
when spinlock debugging is enabled. This happens because there is a legit
nested raw_spinlock->spinlock locking usage within IRQ-related code. IRQ
core uses raw spinlock and then Tegra GPIO driver uses a nested spinlock.
The debug code can't recognize and handle this case, hence we need to use
raw spinlock in the GPIO driver.
[ BUG: Invalid wait context ]
...
(dump_stack) from (__lock_acquire)
(__lock_acquire) from (lock_acquire)
(lock_acquire) from (_raw_spin_lock_irqsave)
(_raw_spin_lock_irqsave) from (tegra_gpio_irq_set_type)
(tegra_gpio_irq_set_type) from (__irq_set_trigger)
(__irq_set_trigger) from (__setup_irq)
(__setup_irq) from (request_threaded_irq)
(request_threaded_irq) from (devm_request_threaded_irq)
(devm_request_threaded_irq) from (elants_i2c_probe)
(elants_i2c_probe) from (i2c_device_probe)
...
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add lockdep class in order to fix debug warnings that are coming from a
legit nested use of irq_set_irq_wake() by the Tegra GPIO driver.
WARNING: possible recursive locking detected
...
(irq_set_irq_wake) from (tegra_gpio_irq_set_wake)
(tegra_gpio_irq_set_wake) from (irq_set_irq_wake)
(irq_set_irq_wake) from (brcmf_sdiod_intr_register [brcmfmac])
...
Tested-by: Peter Geis <pgwipeout@gmail.com>
Reported-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This enables the PEX8311 internal PCI wire interrupt and the PEX8311
local interrupt input so the local interrupts are forwarded to the PCI.
Fixes: 5855620466 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In gpiochip_setup_dev() the call to gpiolib_cdev_register() indirectly
calls device_add(). This is still required for the sysfs even when
CONFIG_GPIO_CDEV is not selected in the build.
Replace the stubbed functions in gpiolib-cdev.h with macros in gpiolib.c
that perform the required device_add() and device_del() when
CONFIG_GPIO_CDEV is not selected.
Fixes: d143493c01 (gpiolib: make cdev a build option)
Reported-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
