Currently firmware passes CCF specific flags to ZynqMP clock driver.
So firmware needs to be updated if CCF flags are changed. The firmware
should have its own 'flag number space' that is distinct from the
common clk framework's 'flag number space'. So define and use ZynqMP
specific common clock flags instead of using CCF flags.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Link: https://lore.kernel.org/r/20210628070122.26217-2-rajan.vaja@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When the firmware code is disabled, the incomplete error handling
in the clk driver causes compile-time warnings:
drivers/clk/zynqmp/pll.c: In function 'zynqmp_pll_recalc_rate':
drivers/clk/zynqmp/pll.c:147:29: error: 'fbdiv' is used uninitialized [-Werror=uninitialized]
147 | rate = parent_rate * fbdiv;
| ~~~~~~~~~~~~^~~~~~~
In function 'zynqmp_pll_get_mode',
inlined from 'zynqmp_pll_recalc_rate' at drivers/clk/zynqmp/pll.c:148:6:
drivers/clk/zynqmp/pll.c:61:27: error: 'ret_payload' is used uninitialized [-Werror=uninitialized]
61 | return ret_payload[1];
| ~~~~~~~~~~~^~~
drivers/clk/zynqmp/pll.c: In function 'zynqmp_pll_recalc_rate':
drivers/clk/zynqmp/pll.c:53:13: note: 'ret_payload' declared here
53 | u32 ret_payload[PAYLOAD_ARG_CNT];
| ^~~~~~~~~~~
drivers/clk/zynqmp/clk-mux-zynqmp.c: In function 'zynqmp_clk_mux_get_parent':
drivers/clk/zynqmp/clk-mux-zynqmp.c:57:16: error: 'val' is used uninitialized [-Werror=uninitialized]
57 | return val;
| ^~~
As it was apparently intentional to support this for compile testing
purposes, change the code to have just enough error handling for the
compiler to not notice the remaining bugs.
Fixes: 21f2375346 ("clk: zynqmp: Drop dependency on ARCH_ZYNQMP")
Co-developed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f1c4e8c903fe2d5df5413421920a56890a46387a.1624356908.git.michal.simek@xilinx.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If there is a IOCTL_SET_PLL_FRAC_MODE request sent to ATF ever,
we shouldn't skip invoking PM_CLOCK_ENABLE fn even though this
pll has been enabled. In ATF implementation, it will only assign
the mode to the variable (struct pm_pll *)pll->mode when handling
IOCTL_SET_PLL_FRAC_MODE call. Invoking PM_CLOCK_ENABLE can force
ATF send request to PWU to set the pll mode to PLL's register.
There is a scenario that happens in enabling VPLL_INT(clk_id:96):
1) VPLL_INT has been enabled during booting.
2) A driver calls clk_set_rate and according to the rate, the VPLL_INT
should be set to FRAC mode. Then zynqmp_pll_set_mode is called
to pass IOCTL_SET_PLL_FRAC_MODE to ATF. Note that at this point
ATF just stores the mode to a variable.
3) This driver calls clk_prepare_enable and zynqmp_pll_enable is
called to try to enable VPLL_INT pll. Because of 1), the function
zynqmp_pll_enable just returns without doing anything after checking
that this pll has been enabled.
In the scenario above, the pll mode of VPLL_INT will never be set
successfully. So adding set_pll_mode to check condition to fix it.
Fixes: 3fde0e16d0 ("drivers: clk: Add ZynqMP clock driver")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210406153131.601701-1-quanyang.wang@windriver.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
