The driver was not previously programming the VDD_SEL values for each
output to indicate what external VDDO voltage was used for each. Add
ability to specify a regulator supplying the VDDO pin for each output of
the device. The voltage of the regulator is used to automatically set the
VDD_SEL value appropriately. If no regulator is specified and the chip is
being reconfigured, assume 2.5V which appears to be the chip default.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20210325192643.2190069-7-robert.hancock@calian.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If the Si5341 is being initially programmed and has no stored NVM
configuration, some of the register contents may contain unexpected
values, such as zeros, which could cause divide by zero errors during
driver initialization. Trap errors caused by zero registers or zero clock
rates which could result in divide errors later in the code.
Fixes: 3044a860fd ("clk: Add Si5341/Si5340 driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20210325192643.2190069-4-robert.hancock@calian.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Si5341 datasheet warns that before accessing any other registers,
including the PAGE register, we need to wait for the DEVICE_READY register
to indicate the device is ready, or the process of the device loading its
state from NVM can be corrupted. Wait for DEVICE_READY on startup before
continuing initialization. This is done using a raw I2C register read
prior to setting up regmap to avoid any potential unwanted automatic PAGE
register accesses from regmap at this stage.
Fixes: 3044a860fd ("clk: Add Si5341/Si5340 driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20210325192643.2190069-3-robert.hancock@calian.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Si5341 and Si5340 have multiple input clock options. So far, the driver
only supported the XTAL input, this adds support for the three external
clock inputs as well.
If the clock chip isn't programmed at boot, the driver will default to the
XTAL input as before. If there is no "xtal" clock input available, it will
pick the first connected input (e.g. "in0") as the input clock for the PLL.
One can use clock-assigned-parents to select a particular clock as input.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Link: https://lkml.kernel.org/r/20200107075340.14528-1-mike.looijmans@topic.nl
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Adds a driver for the Si5341 and Si5340 chips. The driver does not fully
support all features of these chips, but allows the chip to be used
without any support from the "clockbuilder pro" software.
If the chip is preprogrammed, that is, you bought one with some defaults
burned in, or you programmed the NVM in some way, the driver will just
take over the current settings and only change them on demand. Otherwise
the input must be a fixed XTAL in its most basic configuration (no
predividers, no feedback, etc.).
The driver supports dynamic changes of multisynth, output dividers and
enabling or powering down outputs and multisynths.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd@kernel.org: Mark some things static, use BIT_ULL for big bits and
ULL for big constants]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
