Pull sound updates from Takashi Iwai:
"It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1"
* tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: hda: intel-dsp-config: reorder the config table
ALSA: hda: intel-dsp-config: add JasperLake support
ALSA: hda: cs35l41: fix double free on error in probe()
ALSA: hda: Fix dependencies of CS35L41 on SPI/I2C buses
ALSA: hda: Fix dependency on ASoC cs35l41 codec
ASoC: cs35l41: Add support for hibernate memory retention mode
ASoC: cs35l41: Update handling of test key registers
ALSA: intel_hdmi: Check for error num after setting mask
ASoC: wcd9335: Keep a RX port value for each SLIM RX mux
ASoC: amd: acp: acp-mach: Change default RT1019 amp dev id
ALSA: virmidi: Remove duplicated code
ALSA: seq: virmidi: Add a drain operation
ASoC: topology: Fix typo
ASoC: fsl_asrc: refine the check of available clock divider
ASoC: Intel: bytcr_rt5640: Add support for external GPIO jack-detect
ASoC: Intel: bytcr_rt5640: Support retrieving the codec IRQ from the AMCR0F28 ACPI dev
ASoC: rt5640: Add support for boards with an external jack-detect GPIO
ASoC: rt5640: Allow snd_soc_component_set_jack() to override the codec IRQ
ASoC: rt5640: Change jack_work to a delayed_work
ASoC: rt5640: Fix possible NULL pointer deref on resume
...
Pull ARM SoC devicetree updates from Arnd Bergmann:
"As usual, this is the bulk of the updates for the SoC tree, adding
more devices to existing files, addressing issues from ever improving
automated checking, and fixing minor issues.
The most interesting bits as usual are the new platforms. All the
newly supported SoCs belong into existing families this time:
- Qualcomm gets support for two newly announced platforms, both of
which can now work in production environments: the SDX65 5G modem
that can run a minimal Linux on its Cortex-A7 core, and the
Snapdragon 8 Gen 1, their latest high-end phone SoC.
- Renesas adds support for R-Car S4-8, the most recent automotive
Server/Communication SoC.
- TI adds support for J721s2, a new automotive SoC in the K3 family.
- Mediatek MT7986a/b is a SoC used in Wifi routers, the latest
generation following their popular MT76xx series. Only basic
support is added for now.
- NXP i.MX8 ULP8 is a new low-power variant of the widespread i.MX8
series.
- TI SPEAr320s is a minor variant of the old SPEAr320 SoC that we
have supported for a long time.
New boards with the existing SoCs include
- Aspeed AST2500/AST2600 BMCs in TYAN, Facebook and Yadro servers
- AT91/SAMA5 based evaluation board
- NXP gains twenty new development and industrial boards for their
i.MX and Layerscape SoCs
- Intel IXP4xx now supports the final two machines in device tree
that were previously only supported in old style board files.
- Mediatek MT6589 is used in the Fairphone FP1 phone from 2013, while
MT8183 is used in the Acer Chromebook 314.
- Qualcomm gains support for the reference machines using the two new
SoCs, plus a number of Chromebook variants and phones based on the
Snapdragon 7c, 845 and 888 SoCs, including various Sony Xperia
devices and the Microsoft Surface Duo 2.
- ST STM32 now supports the Engicam i.Core STM32MP1 carrier board.
- Tegra now boots various older Android devices based on 32-bit chips
out of the box, including a number of ASUS Transformer tablets.
There is also a new Jetson AGX Orin developer kit.
- Apple support adds the missing device trees for all the remaining
M1 Macbook and iMac variants, though not yet the M1 Pro/Max
versions.
- Allwinner now supports another version of the Tanix TX6 set-top box
based on the H6 SoC.
- Broadcom gains support for the Netgear RAXE500 Wireless router
based on BCM4908"
* tag 'dt-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (574 commits)
Revert "ARM: dts: BCM5301X: define RTL8365MB switch on Asus RT-AC88U"
arm64: dts: qcom: sm6125: Avoid using missing SM6125_VDDCX
arm64: dts: qcom: sm8450-qrd: Enable USB nodes
arm64: dts: qcom: sm8450: Add usb nodes
ARM: dts: aspeed: add LCLK setting into LPC KCS nodes
dt-bindings: ipmi: bt-bmc: add 'clocks' as a required property
ARM: dts: aspeed: add LCLK setting into LPC IBT node
ARM: dts: aspeed: p10: Add TPM device
ARM: dts: aspeed: p10: Enable USB host ports
ARM: dts: aspeed: Add TYAN S8036 BMC machine
ARM: dts: aspeed: tyan-s7106: Add uart_routing and fix vuart config
ARM: dts: aspeed: Adding Facebook Bletchley BMC
ARM: dts: aspeed: g220a: Enable secondary flash
ARM: dts: Add openbmc-flash-layout-64-alt.dtsi
ARM: dts: aspeed: Add secure boot controller node
dt-bindings: aspeed: Add Secure Boot Controller bindings
ARM: dts: Remove "spidev" nodes
dt-bindings: pinctrl: samsung: Add pin drive definitions for Exynos850
dt-bindings: arm: samsung: Document E850-96 board binding
dt-bindings: Add vendor prefix for WinLink
...
Because of commit 9cb2ff1117 ("spi: cadence-quadspi: Disable Auto-HW polling"),
which does a write to the CQSPI_REG_WR_COMPLETION_CTRL register
regardless of any condition. Well, the Cadence QuadSPI controller on
Intel's SoCFPGA platforms does not implement the
CQSPI_REG_WR_COMPLETION_CTRL register, thus a write to this register
results in a crash!
So starting with v5.16, I introduced the patch
98d948eb83 ("spi: cadence-quadspi: fix write completion support"),
which adds the dts compatible "intel,socfpga-qspi" that is specific for
versions that doesn't have the CQSPI_REG_WR_COMPLETION_CTRL register implemented.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v3: revert back to "intel,socfpga-qspi"
v2: use both "cdns,qspi-nor" and "cdns,qspi-nor-0010"
Pull ARM SoC fixes from Arnd Bergmann:
"This is my last set of fixes for 5.16, including
- multiple code fixes for the op-tee firmware driver
- Two patches for allwinner SoCs, one fixing the phy mode on a board,
the other one fixing a driver bug in the "RSB" bus driver. This was
originally targeted for 5.17, but seemed worth moving to 5.16
- Two small fixes for devicetree files on i.MX platforms, resolving
problems with ethernet and i2c"
* tag 'arm-fixes-5.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
optee: Suppress false positive kmemleak report in optee_handle_rpc()
tee: optee: Fix incorrect page free bug
arm64: dts: lx2160a: fix scl-gpios property name
tee: handle lookup of shm with reference count 0
ARM: dts: imx6qdl-wandboard: Fix Ethernet support
bus: sunxi-rsb: Fix shutdown
arm64: dts: allwinner: orangepi-zero-plus: fix PHY mode
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.17, please pull the following:
- Rafal adds and documents the Netgear RAXE500 Wireless router based on
the BCM4908 SoC.
* tag 'arm-soc/for-5.17/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: bcm4908: add DT for Netgear RAXE500
dt-bindings: arm: bcm: document Netgear RAXE500 binding
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM64 DeviceTree updates for v5.17
This introduces initial support for the brand new Snapdragon 8 Gen 1,
aka SM8450 platform, with SMP, CPUfreq, cluster idling, low speed buses,
TLMM pinctrl, SMMU, regulators, clocks, power-domains, UFS storage and
USB currently supported.
SDM845 adds new support for Sony Xperia XZ2, XZ2C and XZ3. The Lenovo
Yoga C630 gains a few audio related fixes. The PMIC's VADC channels are
described as thermal zones. OnePlus devices gains msm-id and board-id,
to facilitate a single firmware image for the multiple devices.
On SM8350 the Sony Xperia 1 III and 5 III, as well as initial
description of Microsoft's Surface Duo 2 are introduced. On the
platform side, LLCC, QUP nodes, redistributor stride and all the
low-speed QUPs are added
MSM8996 gained various regulator fixes, and adsp firmware name to
faciliate pushing firmware to linux-firmware. Xiaomi Mi Note 2 gained
touchkey controller definition.
On SDM660 the Xiaomi Redmi Note 7 gained power and volume keys, RPM and
regulator definitions, USB, eMMC and SD-card and a simple-framebuffer
description.
MSM8916 has the mmc aliases corrected, to stop the storage devices to
move around and the RPM sleep stats memory is described. Support for the
Samsung J5 2015 smartphone is introduced.
SM6350 validation errors are fixed and and description of the audio,
compute and modem remoteprocs are added.
A couple new revisions of the SC7180 based Google devices are added.
The SC7280 platform gains venus and a few fixes. The CRD development
device is introduced, with the EC, touchscreen and touchpad.
On SM8250 CPU opp-tables, for scaling L3 cache and DDR frequency based
on CPU frequency, are added. As is TX, RX macros and SoundWire blocks
and used to enable audio on the SM8350 MTP.
* tag 'qcom-arm64-for-5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (92 commits)
arm64: dts: qcom: sm6125: Avoid using missing SM6125_VDDCX
arm64: dts: qcom: sm8450-qrd: Enable USB nodes
arm64: dts: qcom: sm8450: Add usb nodes
arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes
arm64: dts: qcom: sm8450: add cpufreq support
arm64: dts: qcom: sm8450: Add rpmhpd node
arm64: dts: qcom: sm8450-qrd: enable ufs nodes
arm64: dts: qcom: sm8450: add ufs nodes
arm64: dts: qcom: sm8450-qrd: Add rpmh regulator nodes
arm64: dts: qcom: Add base SM8450 QRD DTS
arm64: dts: qcom: sm8450: add smmu nodes
arm64: dts: qcom: sm8450: Add reserved memory nodes
arm64: dts: qcom: sm8450: Add tlmm nodes
arm64: dts: qcom: Add base SM8450 DTSI
arm64: dts: qcom: ipq6018: Fix gpio-ranges property
arm64: dts: qcom: sdm845: add QFPROM chipset specific compatible
arm64: dts: qcom: sdm845: mtp: Add vadc channels and thermal zones
arm64: dts: qcom: pm8998: Add ADC Thermal Monitor node
arm64: qcom: dts: drop legacy property #stream-id-cells
Revert "arm64: dts: qcom: sm8350: Specify clock-frequency for arch timer"
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The SM6125_VDDCX constant is introduced through a separate branch and is
not available in the dts branch. Temporarily replace the constant with
it's value to avoid the build breakage.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Samsung DTS ARM64 changes for v5.17
1. Add bindings for: Exynos USI, Samsung Galaxy A8 (2018) board, WinLink
E850-96 board and WinLink vendor prefix.
2. Add pinctrl definitions used for Exynos850.
3. Minor fixes and improvements.
4. Convert serial on ExynosAutov9 to new hierarchy where serial is part
of USI node.
* tag 'samsung-dt64-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: pinctrl: samsung: Add pin drive definitions for Exynos850
dt-bindings: arm: samsung: Document E850-96 board binding
dt-bindings: Add vendor prefix for WinLink
dt-bindings: arm: samsung: document jackpotlte board binding
dt-bindings: soc: samsung: Fix I2C clocks order in USI binding example
arm64: dts: exynos: convert serial_0 to USI on ExynosAutov9
dt-bindings: soc: samsung: Add Exynos USI bindings
arm64: dts: exynos: Rename hsi2c nodes to i2c for Exynos5433 and Exynos7
Link: https://lore.kernel.org/r/20211220115530.30961-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX arm64 device tree change for 5.17:
- New SoC support: i.MX8 ULP.
- New board support: i.MX8MM/MN based TQMa8Mx boards, iMX8MN BSH SMM S2,
i.MX8 ULP EVK.
- A series from Adam Ford to enable Camera and USB support for
imx8mm-beacon device.
- Add overlays for various serdes protocols on LS1028A QDS board using
different PHY cards.
- A series from Biwen Li to update LS1028A devices around RTC, flextimer
and PWM support.
- A series from Joakim Zhang to update ENET/FEC suppport on i.MX8M
devices.
- A couple of changes from Lucas Stach to update nitrogen8-som Ethernet
PHY and I2C1 pad configuration.
- A series from Martin Kepplinger to split out a shared imx8mq-librem5-r3
dtsi for Librem5 devices.
- Add cache descriptions for i.MX8 SoCs.
- A series from Vladimir Oltean to update ls1028a-rdb device tree in
order to share the DTS between Linux and U-Boot.
- Random device addtion to various i.MX8 and LX2160A based devices.
* tag 'imx-dt64-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (56 commits)
arm64: dts: imx8mp-evk: configure multiple queues on eqos
arm64: dts: ls1028a-qds: add overlays for various serdes protocols
arm64: dts: ls1028a-qds: enable lpuart1
arm64: dts: ls1028a-qds: move rtc node to the correct i2c bus
arm64: dts: ls1028a-rdb: enable pwm0
arm64: dts: ls1028a: add flextimer based pwm nodes
arm64: dts: ls1028a: add ftm_alarm1 node to be used as wakeup source
arm64: dts: ls1028a: Add PCIe EP nodes
arm64: dts: lx2162a-qds: add interrupt line for RTC node
arm64: dts: lx2162a-qds: support SD UHS-I and eMMC HS400 modes
arm64: dts: lx2160a: enable usb3-lpm-capable for usb3 nodes
arm64: dts: lx2160a-qds: Add mdio mux nodes
arm64: dts: lx2160a: add optee-tz node
arm64: dts: lx2160a-rdb: Add Inphi PHY node
arm64: dts: imx8mm: don't assign PLL2 in SoC dtsi
arm64: dts: nitrogen8-som: correct i2c1 pad-ctrl
arm64: dts: nitrogen8-som: correct network PHY reset
arm64: dts: imx8mn-bsh-smm-s2/pro: Add iMX8MN BSH SMM S2 boards
arm64: dts: imx8mm/n: Remove the 'pm-ignore-notify' property
arm64: dts: imx8ulp: add power domain entry for usdhc
...
Link: https://lore.kernel.org/r/20211218071427.26745-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Devicetree changes for TI K3 platforms for v5.17 merge window:
* New Platforms:
- J721s2 SoC, SoM and Common Processor Board support
* New features:
- CAN support on AM64 EVM and SK
- TimeSync Router on AM64
* Fixes:
- Correct d-cache-sets info on J7200
- Fix L2 cache-sets value for J721e/J7200/AM64
- Fixes for dtbs_check warnings wrt serdes_ln_ctrl node on J721e/J7200
- Disable McASP on IoT2050 board to fix dtbs_check warnings
* tag 'ti-k3-dt-for-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
arch: arm64: ti: Add support J721S2 Common Processor Board
arm64: dts: ti: Add initial support for J721S2 System on Module
arm64: dts: ti: Add initial support for J721S2 SoC
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721S2
dt-bindings: arm: ti: Add bindings for J721s2 SoC
arm64: dts: ti: iot2050: Disable mcasp nodes at dtsi level
arm64: dts: ti: k3-am642-evm/sk: Add support for main domain mcan nodes in EVM and disable them on SK
arm64: dts: ti: k3-am64-main: Add support for MCAN
arm64: dts: ti: k3-j721e-common-proc-board: Add support for mcu and main mcan nodes
arm64: dts: ti: k3-j721e: Add support for MCAN nodes
arm64: dts: ti: am654-base-board/am65-iot2050-common: Disable mcan nodes
arm64: dts: ti: k3-am65-mcu: Add Support for MCAN
arm64: dts: ti: k3-am64-main: add timesync router node
arm64: dts: ti: k3-j7200: Correct the d-cache-sets info
arm64: dts: ti: k3-j721e: Fix the L2 cache sets
arm64: dts: ti: k3-j7200: Fix the L2 cache sets
arm64: dts: ti: k3-am642: Fix the L2 cache sets
arm64: dts: ti: j721e-main: Fix 'dtbs_check' in serdes_ln_ctrl node
arm64: dts: ti: j7200-main: Fix 'dtbs_check' serdes_ln_ctrl node
arm64: dts: ti: k3-j721e: correct cache-sets info
Link: https://lore.kernel.org/r/20211217172806.10023-2-vigneshr@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: tegra: Device tree changes for v5.17-rc1
The vast majority of this contains various updates and cleanups to the
Tegra device trees that will eventually help validate all of them using
the dt-schema infrastructure.
Another notable chunk of this contains additional Tegra234 support as
well as support for the new Jetson AGX Orin Developer Kit.
* tag 'tegra-for-5.17-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (47 commits)
arm64: tegra: Add host1x hotflush reset on Tegra210
arm64: tegra: Hook up MMC and BPMP to memory controller
arm64: tegra: Add memory controller on Tegra234
arm64: tegra: Add EMC general interrupt on Tegra194
arm64: tegra: Update SDMMC4 speeds for Tegra194
arm64: tegra: Add dma-coherent for Tegra194 VIC
arm64: tegra: Rename Ethernet PHY nodes
arm64: tegra: Remove unused only-1-8-v properties
arm64: tegra: Sort Tegra210 XUSB clocks correctly
arm64: tegra: Add missing TSEC properties on Tegra210
arm64: tegra: jetson-nano: Remove extra PLL power supplies for PCIe and XUSB
arm64: tegra: smaug: Remove extra PLL power supplies for XUSB
arm64: tegra: jetson-tx1: Remove extra PLL power supplies for PCIe and XUSB
arm64: tegra: Rename GPIO hog nodes to match schema
arm64: tegra: Remove unsupported regulator properties
arm64: tegra: Rename TCU node to "serial"
arm64: tegra: Remove undocumented Tegra194 PCIe "core_m" clock
arm64: tegra: Drop unused properties for Tegra194 PCIe
arm64: tegra: Fix Tegra194 HSP compatible string
arm64: tegra: Drop unsupported nvidia,lpdr property
...
Link: https://lore.kernel.org/r/20211217162253.1801077-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CN9130 has a built-in CP115 which has 2 GPIO controllers, but unlike in
Armada 7k and 8k both are left disabled by the SoC DTSI.
This first of all makes no sense as they are always present due to being
SoC built-in and its an issue as boards like CN9130-CRB use the CPO GPIO2
pins for regulators and SD card support without enabling them first.
So, enable both of them like Armada 7k and 8k do.
Fixes: 6b8970bd8d ("arm64: dts: marvell: Add support for Marvell CN9130 SoC support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
CN9130 has one CP115 built in, which like the CP110 has 2 GPIO and 2 SPI
controllers built-in.
However, unlike the Armada 7k and 8k the SoC DTSI doesn't add the required
aliases as both the Orion SPI driver and MVEBU GPIO drivers require the
aliases to be present.
So add the required aliases for GPIO and SPI controllers.
Fixes: 6b8970bd8d ("arm64: dts: marvell: Add support for Marvell CN9130 SoC support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Kernel driver phy-mvebu-a3700-comphy.c needs to know the rate of the
reference xtal clock. So add missing xtal clock source into comphy device
tree node. If the property is not present, the driver defaults to 25 MHz
xtal rate (which, as far as we know, is used by all the existing boards).
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Pull ARM SoC fixes from Arnd Bergmann:
"There are a number of DT fixes, mostly for mistakes found through
static checking of the dts files again, as well as a couple of minor
changes to address incorrect DT settings.
For i.MX, there is yet another series of devitree changes to update
RGMII delay settings for ethernet, which is an ongoing problem after
some driver changes.
For SoC specific device drivers, a number of smaller fixes came up:
- i.MX SoC identification was incorrectly registered non-i.MX
machines when the driver is built-in
- One fix on imx8m-blk-ctrl driver to get i.MX8MM MIPI reset work
properly
- a few compile fixes for warnings that get in the way of -Werror
- a string overflow in the scpi firmware driver
- a boot failure with FORTIFY_SOURCE on Rockchips machines
- broken error handling in the AMD TEE driver
- a revert for a tegra reset driver commit that broke HDA"
* tag 'soc-fixes-5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
soc/tegra: fuse: Fix bitwise vs. logical OR warning
firmware: arm_scpi: Fix string overflow in SCPI genpd driver
soc: imx: Register SoC device only on i.MX boards
soc: imx: imx8m-blk-ctrl: Fix imx8mm mipi reset
ARM: dts: imx6ull-pinfunc: Fix CSI_DATA07__ESAI_TX0 pad name
arm64: dts: imx8mq: remove interconnect property from lcdif
ARM: socfpga: dts: fix qspi node compatible
arm64: dts: apple: add #interrupt-cells property to pinctrl nodes
dt-bindings: i2c: apple,i2c: allow multiple compatibles
arm64: meson: remove COMMON_CLK
arm64: meson: fix dts for JetHub D1
tee: amdtee: fix an IS_ERR() vs NULL bug
arm64: dts: apple: change ethernet0 device type to ethernet
arm64: dts: ten64: remove redundant interrupt declaration for gpio-keys
arm64: dts: rockchip: fix poweroff on helios64
arm64: dts: rockchip: fix audio-supply for Rock Pi 4
arm64: dts: rockchip: fix rk3399-leez-p710 vcc3v3-lan supply
arm64: dts: rockchip: fix rk3308-roc-cc vcc-sd supply
arm64: dts: rockchip: remove mmc-hs400-enhanced-strobe from rk3399-khadas-edge
ARM: rockchip: Use memcpy_toio instead of memcpy on smp bring-up
...
Use the interconnects property to hook up the MMC and BPMP to the memory
controller. This is needed to set the correct bus-level DMA mask, which
is a prerequisite for adding IOMMU support.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds the memory controller and the embedded external memory
controller found on the Tegra234 SoC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
DMA operations for the Tegra194 Video Image Compositor (VIC) are
coherent and so populate the 'dma-coherent' property.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make the order of the clocks and clock-names properties match the order
in the device tree bindings. This isn't strictly necessary from a point
of view of the operating system because matching will be done based on
the clock-names, but it makes it easier to validate the device trees
against the DT schema.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add missing interrupts, clocks, clock-names, reset and reset-names
properties for the TSEC blocks found on Tegra210.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the PCIe and XUSB controller device
tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the XUSB controller device tree
node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the PCIe and XUSB controller device
tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
GPIO hog nodes must have a "hog-" prefix or "-hog" suffix according to
the DT schema. Rename all such nodes to allow validation to pass.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the unsupported "regulator-disable-ramp-delay" properties which
ended up in various DTS files for some reason.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The num-viewport property is never used and can be dropped, whereas the
"iommus" property is not needed since we use "iommu-map-mask" and
"iommu-map" already.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HSP instances on Tegra194 are not fully compatible with the version
found on Tegra186, so drop the fallback compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra194 pinmux DT bindings do not define the nvidia,lpdr property,
so drop them from the device trees that have listed them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The standard "jedec," vendor prefix should be used for SPI NOR flash
chips. This allows the right DT schema to be picked for validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra186 CCPLEX cluster register region is 4 MiB is length, not 4
MiB - 1. This was likely presumed to be the "limit" rather than length.
Fix it up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
