Memory controller drivers for v5.16
1. Renesas RPC: fix unaligned bus access and QSPI data transfers in
manual modes.
2. Renesas RPC: select RESET_CONTROLLER as it is necessary for
operation.
3. FSL IFC: fix error paths.
4. Broadcom: allow building as module.
* tag 'memory-controller-drv-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
memory: fsl_ifc: fix leak of irq and nand_irq in fsl_ifc_ctrl_probe
memory: renesas-rpc-if: RENESAS_RPCIF should select RESET_CONTROLLER
memory: brcmstb_dpfe: Allow building Broadcom STB DPFE as module
memory: samsung: describe drivers in KConfig
memory: renesas-rpc-if: Avoid unaligned bus access for HyperFlash
memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode
dt-bindings: rpc: renesas-rpc-if: Add support for the R8A779A0 RPC-IF
Link: https://lore.kernel.org/r/20211010175836.13302-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Memory controller drivers for v5.14 - Mediatek
Add MT8195 support to the Mediatek SMI memory controller driver. This
brings also several cleanups and minor enhancements before adding actual
new device support.
* tag 'memory-controller-drv-mtk-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
MAINTAINERS: Add entry for MediaTek SMI
memory: mtk-smi: mt8195: Add initial setting for smi-larb
memory: mtk-smi: mt8195: Add initial setting for smi-common
memory: mtk-smi: mt8195: Add smi support
memory: mtk-smi: Use devm_platform_ioremap_resource
memory: mtk-smi: Add clocks for smi-sub-common
memory: mtk-smi: Add device link for smi-sub-common
memory: mtk-smi: Add error handle for smi_probe
memory: mtk-smi: Adjust some code position
memory: mtk-smi: Rename smi_gen to smi_type
memory: mtk-smi: Use clk_bulk clock ops
dt-bindings: memory: mediatek: Add mt8195 smi sub common
dt-bindings: memory: mediatek: Add mt8195 smi binding
Link: https://lore.kernel.org/r/20211010175836.13302-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This binding is meant for the child nodes of the TI GPMC node. The node
represents any device connected to the GPMC bus. It may be a Flash chip,
RAM chip or Ethernet controller, etc. These properties are meant for
configuring the GPMC settings/timings and will accompany the bindings
supported by the respective device.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no GPMC Ethernet compatible or device driver. GPMC is
just a bus interface over which devices like Ethernet controller
can be to.
For SMSC 911x Ethernet chip bindings, please refer to
Documentation/devicetree/bindings/net/smsc,lan9115.yaml
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no GPMC NOR compatible or device driver. GPMC is just
a bus interface over which standard (CFI/JEDC) NOR Flash chips
can be attached.
For NOR chip bindings, please refer to
Documentation/devicetree/bindings/mtd/mtd-physmap.yaml
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both hardware and driver can communicate DDC over i2c bus.
Fixes warnings as:
arch/arm/boot/dts/tegra20-paz00.dt.yaml: panel: 'ddc-i2c-bus' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: /home/runner/work/linux/linux/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210927214503.36012-1-david@ixit.cz
This tablet display is unique and hence must be added to documentation.
Unfortunately, it's real make and number is not known due to obscure and
missing documentation and lack of writing on the display assembly
itself.
So the natural alternative that came to mind is to name the panel after
the device that contained it (an Android tablet). Hopefully that isn't
an issue.
I can confirm that the parameters that I've obtained are correct since
they came from a dump of the original Android OS.
Signed-off-by: Nikola Pavlica <pavlica.nikola@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211002202905.509437-2-pavlica.nikola@gmail.com
The Vitesse/Microsemi/Microchip family of switches supported by the
Felix DSA driver is capable of selecting between the native tagging
protocol and ocelot-8021q. This is necessary to enable flow control on
the CPU port.
Certain systems where these switches are integrated use the switch as a
port multiplexer, so the termination throughput is paramount. Changing
the tagging protocol at runtime is possible for these systems, but since
it is known beforehand that one tagging protocol will provide strictly
better performance than the other, just allow them to specify the
preference in the device tree.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hi All,
Changes since v2
================
1. Add Stephen's and Rob's tags.
2. Correct inb-supply description in patch 10/10.
Changes since v2
================
1. Add Rob's tags.
2. Remove "regulator-name" from properties (all regulator dtschema).
3. Move "unevaluatedProperties" higher to make code easier to read (all regulator dtschema).
4. Add ref-type to op-mode property (patch 6: s5m8767 regulators).
Changes since v1
================
1. Drop DTS patches - applied.
2. Fully remove bindings/regulator/samsung,s5m8767.txt .
3. Minor subject reformatting and few typos in text.
Intro
=====
This patchset converts all devicetree bindings of Samsung S2M and S5M
PMIC devices from txt to dtschema.
It includes also two fixes because later conversion depends on it
(contextually).
Merging/dependencies
====================
1. Regulator related binding changes depend on first two commits (the
fixes), because of context.
2. The mfd bindings depend on clock and regulator bindings.
The fixes and bindings changes (patches 1-10) should go via the same
tree. For example regulator or mfd tree.
Another alternative is that regulator patches (1-2, 4-6) go via Mark who
later gives MFD a stable branch/tag to pull. Then the clock and MFD
bindings would go on top via MFD tree. Or any other setup you would like
to have.
Overview of devices
===================
Essentially all Samsung S2M and S5M PMICs are very similar devices. They
provide the same functionality: regulators, RTC, 2 or 3 clocks and main
power management (e.g. power cut to SoC).
The differences are mostly in registers layout and number of regulators.
The drivers are built around one common part, mfd/sec-core.c, and share
some drivers between devices:
1. MFD sec-core for all devices,
1. one clock driver for most of devices,
2. one RTC driver for all devices,
3. three regulator drivers.
The regulator drivers were implementing slightly different features,
therefore one regulator binding for all devices does not make much
sense. However the clock device binding can be shared.
The final dtschema bindings try to implement this - share only the clock
bindings.
Best regards,
Krzysztof
Krzysztof Kozlowski (10):
regulator: s5m8767: do not use reset value as DVS voltage if GPIO DVS
is disabled
regulator: dt-bindings: samsung,s5m8767: correct
s5m8767,pmic-buck-default-dvs-idx property
dt-bindings: clock: samsung,s2mps11: convert to dtschema
regulator: dt-bindings: samsung,s2m: convert to dtschema
regulator: dt-bindings: samsung,s2mpa01: convert to dtschema
regulator: dt-bindings: samsung,s5m8767: convert to dtschema
dt-bindings: mfd: samsung,s2mps11: convert to dtschema
dt-bindings: mfd: samsung,s2mpa01: convert to dtschema
dt-bindings: mfd: samsung,s5m8767: convert to dtschema
dt-bindings: mfd: samsung,s5m8767: document buck and LDO supplies
.../bindings/clock/samsung,s2mps11.txt | 49 ---
.../bindings/clock/samsung,s2mps11.yaml | 45 +++
.../bindings/mfd/samsung,s2mpa01.yaml | 91 ++++++
.../bindings/mfd/samsung,s2mps11.yaml | 267 +++++++++++++++
.../bindings/mfd/samsung,s5m8767.yaml | 307 ++++++++++++++++++
.../bindings/mfd/samsung,sec-core.txt | 86 -----
.../bindings/regulator/samsung,s2mpa01.txt | 79 -----
.../bindings/regulator/samsung,s2mpa01.yaml | 62 ++++
.../bindings/regulator/samsung,s2mps11.txt | 102 ------
.../bindings/regulator/samsung,s2mps11.yaml | 44 +++
.../bindings/regulator/samsung,s2mps13.yaml | 44 +++
.../bindings/regulator/samsung,s2mps14.yaml | 44 +++
.../bindings/regulator/samsung,s2mps15.yaml | 44 +++
.../bindings/regulator/samsung,s2mpu02.yaml | 44 +++
.../bindings/regulator/samsung,s5m8767.txt | 145 ---------
.../bindings/regulator/samsung,s5m8767.yaml | 74 +++++
MAINTAINERS | 9 +-
drivers/regulator/s5m8767.c | 21 +-
18 files changed, 1080 insertions(+), 477 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/clock/samsung,s2mps11.txt
create mode 100644 Documentation/devicetree/bindings/clock/samsung,s2mps11.yaml
create mode 100644 Documentation/devicetree/bindings/mfd/samsung,s2mpa01.yaml
create mode 100644 Documentation/devicetree/bindings/mfd/samsung,s2mps11.yaml
create mode 100644 Documentation/devicetree/bindings/mfd/samsung,s5m8767.yaml
delete mode 100644 Documentation/devicetree/bindings/mfd/samsung,sec-core.txt
delete mode 100644 Documentation/devicetree/bindings/regulator/samsung,s2mpa01.txt
create mode 100644 Documentation/devicetree/bindings/regulator/samsung,s2mpa01.yaml
delete mode 100644 Documentation/devicetree/bindings/regulator/samsung,s2mps11.txt
create mode 100644 Documentation/devicetree/bindings/regulator/samsung,s2mps11.yaml
create mode 100644 Documentation/devicetree/bindings/regulator/samsung,s2mps13.yaml
create mode 100644 Documentation/devicetree/bindings/regulator/samsung,s2mps14.yaml
create mode 100644 Documentation/devicetree/bindings/regulator/samsung,s2mps15.yaml
create mode 100644 Documentation/devicetree/bindings/regulator/samsung,s2mpu02.yaml
delete mode 100644 Documentation/devicetree/bindings/regulator/samsung,s5m8767.txt
create mode 100644 Documentation/devicetree/bindings/regulator/samsung,s5m8767.yaml
--
2.30.2
Pull drm fixes from Dave Airlie:
"I've returned from my tropical island retreat, even managed to bring
one of my kids on a dive with some turtles. Thanks to Daniel for doing
last week's work.
Otherwise this is the weekly fixes pull, it's a bit bigger because the
vc4 reverts in your tree caused some problems with fixes in the
drm-misc tree so it got left out last week, so this week has the misc
fixes rebased without the vc4 pieces.
Otherwise it's i915, amdgpu with the usual fixes and a scattering over
other drivers.
I expect things should calm down a bit more next week.
core:
- Kconfig fix for fb_simple vs simpledrm.
i915:
- Fix RKL HDMI audio
- Fix runtime pm imbalance on i915_gem_shrink() error path
- Fix Type-C port access before hw/sw state sync
- Fix VBT backlight struct version/size check
- Fix VT-d async flip on SKL/BXT with plane stretch workaround
amdgpu:
- DCN 3.1 DP alt mode fixes
- S0ix gfxoff fix
- Fix DRM_AMD_DC_SI dependencies
- PCIe DPC handling fix
- DCN 3.1 scaling fix
- Documentation fix
amdkfd:
- Fix potential memory leak
- IOMMUv2 init fixes
vc4 (there were some hdmi fixes but things got reverted, sort it out
later):
- compiler fix
nouveau:
- Cursor fix
- Fix ttm buffer moves for ampere gpu's by adding minimal
acceleration support.
- memory leak fixes
rockchip:
- crtc/clk fixup
panel:
- ili9341 Fix DT bindings indent
- y030xx067a - yellow tint init seq fix
gbefb:
- Fix gbefb when built with COMPILE_TEST"
* tag 'drm-fixes-2021-10-08' of git://anongit.freedesktop.org/drm/drm: (33 commits)
drm/amd/display: Fix detection of 4 lane for DPALT
drm/amd/display: Limit display scaling to up to 4k for DCN 3.1
drm/amd/display: Skip override for preferred link settings during link training
drm/nouveau/debugfs: fix file release memory leak
drm/nouveau/kms/nv50-: fix file release memory leak
drm/nouveau: avoid a use-after-free when BO init fails
DRM: delete DRM IRQ legacy midlayer docs
video: fbdev: gbefb: Only instantiate device when built for IP32
fbdev: simplefb: fix Kconfig dependencies
drm/panel: abt-y030xx067a: yellow tint fix
dt-bindings: panel: ili9341: correct indentation
drm/nouveau/fifo/ga102: initialise chid on return from channel creation
drm/rockchip: Update crtc fixup to account for fractional clk change
drm/nouveau/ga102-: support ttm buffer moves via copy engine
drm/nouveau/kms/tu102-: delay enabling cursor until after assign_windows
drm/sun4i: dw-hdmi: Fix HDMI PHY clock setup
drm/vc4: hdmi: Remove unused struct
drm/kmb: Enable alpha blended second plane
drm/amdgpu: handle the case of pci_channel_io_frozen only in amdgpu_pci_resume
drm/amdgpu: init iommu after amdkfd device init
...
The driver and its bindings, before commit 04f9f068a6 ("regulator:
s5m8767: Modify parsing method of the voltage table of buck2/3/4") were
requiring to provide at least one safe/default voltage for DVS registers
if DVS GPIO is not being enabled.
IOW, if s5m8767,pmic-buck2-uses-gpio-dvs is missing, the
s5m8767,pmic-buck2-dvs-voltage should still be present and contain one
voltage.
This requirement was coming from driver behavior matching this condition
(none of DVS GPIO is enabled): it was always initializing the DVS
selector pins to 0 and keeping the DVS enable setting at reset value
(enabled). Therefore if none of DVS GPIO is enabled in devicetree,
driver was configuring the first DVS voltage for buck[234].
Mentioned commit 04f9f068a6 ("regulator: s5m8767: Modify parsing
method of the voltage table of buck2/3/4") broke it because DVS voltage
won't be parsed from devicetree if DVS GPIO is not enabled. After the
change, driver will configure bucks to use the register reset value as
voltage which might have unpleasant effects.
Fix this by relaxing the bindings constrain: if DVS GPIO is not enabled
in devicetree (therefore DVS voltage is also not parsed), explicitly
disable it.
Cc: <stable@vger.kernel.org>
Fixes: 04f9f068a6 ("regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Message-Id: <20211008113723.134648-2-krzysztof.kozlowski@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hello,
while trying to understand how the spi framework makes use of the core
device driver stuff (to fix a deadlock) I found these simplifications
and improvements.
They are build-tested with allmodconfig on arm64, m68k, powerpc, riscv,
s390, sparc64 and x86_64.
Best regards
Uwe
Uwe Kleine-König (4):
spi: Move comment about chipselect check to the right place
spi: Remove unused function spi_busnum_to_master()
spi: Reorder functions to simplify the next commit
spi: Make several public functions private to spi.c
Documentation/spi/spi-summary.rst | 8 -
drivers/spi/spi.c | 237 ++++++++++++------------------
include/linux/spi/spi.h | 55 -------
3 files changed, 95 insertions(+), 205 deletions(-)
base-commit: 9e1ff307c7
--
2.30.2
