There is an uppercase 'N' that should be a lowercase 'n', fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This recently added macro provides more meaningful error messages thanks
to identifying a specific wiphy. It's especially important on systems
with few cards supported by the same (brcmfmac) driver.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We do not need separate lines for calculating register values.
Also add comment that value is different than in vendor driver.
Suggested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The TX_PIN_CFG_RFRX_EN bit was not set on other devices than MT7620,
restore old behavaviour since setting this bit maight not be
correct for older devices.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not enable TX_PIN_CFG_LNA_PE_A* bits for 2.4GHz band and
vice versa TX_PIN_CFG_LNA_PE_G* bits for 5GHz.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register 66 was causing issues on RT6352 if set to the same value as
in MTK driver. With 1c reg value device was working fine in both HT20
and HT40 modes.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove band check from rf53xx channel config routine since all chips
using it are single band.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The parameter order for clamp is supposed to be clamp(value, low, high).
When we write it in this order it's equivalent to
min(head->plcp[3] & 0x7f, 75) which works in this context where the min
is zero. But it's not a correct use of the API.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c: In function 'rtl8180_probe':
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1727:15: warning:
variable 'io_addr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1726:16: warning:
variable 'mem_addr' set but not used [-Wunused-but-set-variable]
They're never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace hard coded function name with __func__, to
improve robustness and to conform to the Linux kernel coding
style. Issue found using checkpatch.
Signed-off-by: Keyur Patel <iamkeyur96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As it is, doing something like
# iw phy phy0 interface add foobar type ibss
on a firmware that doesn't have ad-hoc support just yields failures of
HostCmd_CMD_SET_BSS_MODE, which happened to return a '-1' error code
(-EPERM? not really right...) and sometimes may even crash the firmware
along the way.
Let's parse the firmware capability flag while registering the wiphy, so
we don't allow attempting IBSS at all, and we get a proper -EOPNOTSUPP
from nl80211 instead.
Fixes: e267e71e68 ("mwifiex: Disable adhoc feature based on firmware capability")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NL80211_TX_POWER_LIMITED was treated as NL80211_TX_POWER_AUTOMATIC,
which is the opposite of what should happen and can cause nasty
regulatory problems.
if/else converted to a switch without default to make gcc warn
on unhandled enum values.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/marvell/libertas_tf/main.c: In function 'lbtf_rx':
drivers/net/wireless/marvell/libertas_tf/main.c:554:15: warning:
variable 'flags' set but not used [-Wunused-but-set-variable]
It never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of exposing the signal-to-noise ration, calculate the actual signal
level taking the noise floor into account.
Also, flip the SIGNAL_DBM bit on, so that mac80211 exposes the signal
level along with the station info in scan results. This fills
NetworkManager's "nmcli d wifi output" output with colors, bars and joy.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Also, turn it to a dev_info() to make checkpatch.pl happy.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It doesn't make sense and the USB core warns on each submit of such
URB, easily flooding the message buffer with tracebacks.
Analogous issue was fixed in regular libertas driver in commit 6528d88047
("libertas: don't set URB_ZERO_PACKET on IN USB transfer").
Cc: stable@vger.kernel.org
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Logging each and every command response is way too much for INFO level.
Silence this, unless CONFIG_LIBERTAS_THINFIRM_DEBUG has been enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Steve deRosier <derosier@cal-sierra.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/rsi/rsi_91x_main.c: In function 'rsi_prepare_skb':
drivers/net/wireless/rsi/rsi_91x_main.c:127:24: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/rsi/rsi_91x_main.c:124:28: warning:
variable 'info' set but not used [-Wunused-but-set-variable]
They're not used any more since 160ee2a11c ("rsi: fill rx_params only once.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fixes to spelling mistakes in various files in rsi folder.
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a \b (backspace) character in the message that wasn't intended.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function 'brcmf_usb_state_change':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:578:6: warning:
variable 'old_state' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This macro will be used in more places not just the cfg80211.c. It makes
sense to pass some common struct to it as "struct wiphy" is mostly
referenced in cfg80211 code only.
A very common one (used above the bus abstraction layer) is struct
brcmf_pub. Many functions already keep reference to it which will make
using bphy_err() simpler. It should also allow extending that macro's
logic if it's ever needed.
This improves code recently added in the commit 3ef005b82e ("brcmfmac:
add bphy_err() and use it in the cfg80211.c").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far 160 MHz channels were treated as 20 MHz ones which was breaking
support for 40/80 MHz due to the brcmf_construct_chaninfo() logic and
its assumptions.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1) Use switch to simplify/improve the code & avoid some duplication
2) Add warning for unsupported values
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware is capable of reporting ring status. It's used e.g. to signal
some problem with a specific ring setup. This patch adds support for
printing ring & error number which may be useful for debugging setup
issues.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The local variable chipname is string representation of chip id and revision
which is printed in the good flow of brcmf_fw_alloc_request(). Also use it
for the error path, ie. for unknown/unsupported devices.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the firmware crashes during the probe sequence we provide little
information on what really failed. This patch checks the sdpcm shared
location and show the trap information if a firmware trap has happened.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The MBSS feature was already disabled for bcm43362 as it resulted in a
beacon with BRCM_TEST_SSID regardless user configuration in hostapd. Now
the same has been reported for bcm4330 so disable the feature for this
device as well.
Reported-by: Russell King <linux@armlinux.org.uk>
Tested-by: Christopher Martin <chrsmrtn@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since we moved the drivers debugfs directory under ieee80211 debugfs the
debugfs entries need to be added after wiphy_register() has been called.
For most part that has been done accordingly, but for the debugfs entries
added by SDIO it was not and failed silently. This patch fixes that by
adding a bus-layer callback for it.
Fixes: 856d5a011c ("brcmfmac: allocate struct brcmf_pub instance using wiphy_new()")
Reported-by: Russel King <linux@armlinux.org.uk>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For USB there is no separate channel being used to pass events
from firmware to the host driver and as such are passed over the
data path. In order to detect mock event messages an additional
check is needed on event subtype. This check is added conditionally
using unlikely() keyword.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SSID length as received from firmware should not exceed
IEEE80211_MAX_SSID_LEN as that would result in heap overflow.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
The following checkpatch exceptions are also fixed:
WARNING: line over 80 characters
#316: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/fw.c:1751:
+ SET_8821AE_H2CCMD_AOAC_RSVDPAGE_LOC_GTK_EXT_MEM(u1rsvdpageloc2, GTKEXT_PG);
CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+ (eeaddr+1), hwinfo[eeaddr+1]);
^
CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+ (eeaddr+1), hwinfo[eeaddr+1]);
^
CHECK: spaces preferred around that '+' (ctx:VxV)
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+ if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/
^
WARNING: Comparisons should place the constant on the right side of the test
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+ if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/
CHECK: spaces preferred around that '&' (ctx:VxV)
#501: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2666:
+ pwrinfo24g->bw40_diff[rfpath][txcount] = (hwinfo[eeaddr]&0xf0) >> 4;
^
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
The following checkpatch exceptions are also fixed:
CHECK: No space is necessary after a cast
#211: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:109:
+ (u8 *) (&rfstate));
CHECK: No space is necessary after a cast
#241: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:277:
+ ptmp_byte = (u8 *) (®toset) + index;
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch affects modules rtl8192ce, rtl8192cu, and rtl8192com.
The following checkpatch exceptions are also fixed:
CHECK: No space is necessary after a cast
#237: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/hw.c:90:
+ (u8 *) (&rfstate));
CHECK: No space is necessary after a cast
#744: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:329:
+ pwr_val[i] = (u8) ((writeval & (0x7f <<
CHECK: No space is necessary after a cast
#784: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:365:
+ (u8) writeval);
CHECK: spaces preferred around that '/' (ctx:VxV)
#963: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:513:
+ txqpageunit = txqpagenum/outepnum;
^
CHECK: Unnecessary parentheses around 'outepnum > 1'
#975: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:521:
+ if ((outepnum > 1) && (txqremaininpage))
CHECK: Alignment should match open parenthesis
#1059: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:617:
+static void _rtl92cu_init_chipn_two_out_ep_priority(struct ieee80211_hw *hw,
bool wmm_enable,
ERROR: "foo * bar" should be "foo *bar"
#1940: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:591:
+void rtl92cu_fill_fake_txdesc(struct ieee80211_hw *hw, u8 *pdesc,
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver contains one instance of a CamelCase variable, namely
IS_81xxC_VENDOR_UMC_A_CUT. This macro is never used, thus it is deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
File halbt_precomp.h contains the only CamelCase value, namely
GetDefaultAdapter, but that macro is never used, thus it is deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are a number of CamelCase variables remaining in the source
files of modules rtl_pci, rtl_usb, and rtlwifi.
The following checkpatch excettions are also fixed:
for_kalle1/0001-rtlwifi-Remove-CamelCase-variables-from-base-code.patch
-----------------------------------------------------------------------
CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]'
#68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377:
+ if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) ||
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1])) {
CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1]'
#68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377:
+ if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) ||
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1])) {
WARNING: line over 80 characters
#70: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:379:
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
CHECK: No space is necessary after a cast
#186: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:396:
+ status->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#208: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/trx.c:335:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#243: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:301:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#252: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:368:
+ stats.rx_is40mhzpacket = (bool) GET_RX_DESC_BW(rxdesc);
CHECK: No space is necessary after a cast
#265: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/trx.c:475:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
WARNING: Unnecessary space before function pointer arguments
#455: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:1462:
+ void (*writen_sync) (struct rtl_priv *rtlpriv, u32 addr, void *buf,
WARNING: Unnecessary space before function pointer arguments
#483: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:2257:
+ void (*fill_fake_txdesc) (struct ieee80211_hw *hw, u8 *pdesc,
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The old-style license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hopefully the last set of fixes for 5.0, only fix this time.
mt76
* fix regression with resume on mt76x0u USB devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcaso2AAoJEG4XJFUm622bFJ0H/A/ShVALhS03OHmv0a6APuXP
MxC2ZvZH8NTIEPEx+zOrGvIvimkRT5ib41YuWxvxl74jdbXrrZ98uoYQcR/+i/v5
L9zlkLW5xfg0HV9CMrS64Dx7qmGvqsg3OywMSyeKrx16wOnjYyz9EXiPn1lcOYpl
lvla1TpasmqI9CzF5mudnfvp2Z0Ey2utAei77Siih4M3kFm5P8HNHuFsdaStXZNa
JuWUOm7du0FirOxJ0oGrea2yYRRM5vN9KUQhD/mDHqBBapp5lh835TuJE6PUKs8R
yKEB+TSNKcUIc9KUFi0BDcx8YksAeVLRZAHBgsB0FnbAyKDV438O0YN9AMLwM1o=
=zrqD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-02-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.0
Hopefully the last set of fixes for 5.0, only fix this time.
mt76
* fix regression with resume on mt76x0u USB devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It needs to be unset instead of set
Fixes: 2340523646 ("mt76: fix transmission of encrypted management frames")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since ccmp_pn is u8 *, the second half needs to start at array index 4
instead of 0. Fixes a connection stall after a certain amount of traffic
Fixes: 2340523646 ("mt76: fix transmission of encrypted management frames")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove bogus check for MT_PACKET_ID_NO_ACK in mt76_tx_status_skb_get, which
is already handled in callers and turns timeout calls into no-ops
Do not clean up pending status items on reordering of tx status information
if the timeout is not reached yet
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76_init_stream_cap() and mt76_get_txpower() call __sw_hweight8()
directly, but that's only defined if CONFIG_GENERIC_HWEIGHT is
enabled. The function that works on all architectures is hweight8().
Fixes: 551e1ef4d2 ("mt76: add mt76_init_stream_cap routine")
Fixes: 9313faacbb ("mt76: move mt76x02_get_txpower to mt76 core")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In mt76x02u_skb_dma_info() pad is always non-zero. Patch removes
bogus check and add comments to the function.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During device removal the driver can report multiple error messages.
Use dev_err_ratelimited instead of dev_err to display urb errors
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add disable_usb_sg module parameter to disable scatter-gather on demand
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use linear fragment and not a single usb scatter-gather buffer in mt76u
{tx,rx} datapath if the usb controller has sg data length constraints
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not use scatter-gather buffers for mcu commands.
Introduce mt76u_buf_alloc and mt76u_buf_alloc_sg routines.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76u_check_sg routine in usb.c and introduce sg_en variable
in mt76_usb in order to check if scatter-gather is supported by
mt76u layer
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move q->ndesc initialization before the for loop in mt76u_alloc_rx
since otherwise allocated urbs will not be freed in mt76u_buf_free
Double-check scatterlist pointer in mt76u_buf_free
Fixes: b40b15e152 ("mt76: add usb support to mt76 layer")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix possible NULL pointer dereference in mt76u_mcu_deinit routine that
can occur if initialization path fails before calling mt76u_mcu_init_rx
Fixes: ee676cd501 ("mt76: add driver code for MT76x2u based devices")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We don't need to send firmware data asynchronously, much simpler is just
use synchronous usb_bulk_msg().
Tested-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt76x0_init_txpower in order to initialize max_power per channel
at device bootstrap. Modify mt76x0_get_tx_power_per_rate and
mt76x0_get_power_info signature in order to compute tx power for
non-operating channels
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Initialize target_power variable in mt76x0_phy_set_txpower in order to
report target_power in debugfs
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is no need to retun 0 in mt76_dma_attach(), so switch it to void.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x2_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x2_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x0u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x0u_probe and in mt76x0e_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76x2u_alloc_device since it just runs mt76_alloc_device.
Move mt76_alloc_device call in mt76x2u_probe
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x{0,2} alloc_device common code in mt76_alloc_device and
remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Block only when the busy time reaches 92%, as lower values can be reached with
heavy 802.11 traffic as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Based on system load and time needed by other calibration runs, the time
between dev->mac_work runs can vary quite a bit.
Calculate busy time based on the actual time difference in order to avoid
potentially over-estimating busy time, which could lead to unnecessary tx
blocking.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ED/CCA Tx blocking checks need to be run every 100 ms in order to avoid
triggering too late and keeping tx blocking on for too long
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Software encrypted packets can be passed not just through the drv_tx callback,
but also through the intermediate tx queue.
In order to deal with that, move the override to mt76x02_mac_write_txwi and
also take care of filling in the per-packet rate information
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove add_buf function pointer in mt76_queue_ops data structure since
it is no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_dma_tx_queue_skb_raw routine in dma.c and add the
corresponding entry in mt76_queue_ops data structure.
mt76_dma_tx_queue_skb_raw will be reused adding support for
mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove useless commented out configuration in mt76x0u_load_firmware
routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_rx_event i mt76-core module and remove duplicated code.
mt76_mcu_rx_event will be reused adding support for mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_get_response in mt76-core module and remove duplicated
code. mt76_mcu_get_response will be reused adding support for mt7603
driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76_mcu_msg_alloc in mt76-core module and remove duplicated code.
mt76_mcu_msg_alloc will be reused adding support for mt7603 driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix rate power configuration for VHT mcs 8 and 9 in
mt76x0_get_tx_power_per_rate. Moreover use the rate power
offset used for HT/VHT mcs 6 even for HT/VHT mcs 7
Fixes: b37bbc8c82 ("mt76x0: remove eeprom dependency from mt76x0_set_tx_power_per_rate")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we implement beconing on USB now, similar interfaces should be
supported for USB as are for MMIO. Tested only on IBSS mode and
AP mode (not enabled due to lack of PS buffering).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure beaconing on USB devices without PS buffering support.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Disable BEACON timer during init and configure interrupt registers
only for mmio devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
BSSID is not strtirct related with beaconing (for example we can have
2 STA vifs) and more related with MAC address, so initaize BSSID when
setting MAC address.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we now support mt76x2u feature to allow set mac address
when creating interface in common code we can use it for
mt76x2u.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use vif_mask to count interfaces to allow to set mac address in HW
if there is only one interface and report error if we create
interface with wrong BSSID resulting in already used index.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
AP interfaces still use some static TX queues (for probes,
broadcast and multicast frames). These queues were not stopped
correctly when the transport layer indicated the queue should be
stopped. As a result, when flushing the queues, new frames from
the overflow queue were tx'd, so the queues still had frames after
flushing. This ended up in an assert since trying to remove a station
with non-empty queues.
Fix it by stopping the static queues correctly when required.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add IWL_FW_INI_APPLY_EARLY and IWL_FW_INI_APPLY_AFTER_ALIVE apply points
to unified images.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When HW restart is requested but not started yet, commands would not
be sent to the FW, and some function calls would return an error. In
case of iwl_mvm_mac_sta_state() returning an error value when a
station is removed can lead to an unneeded warning in
__sta_info_destroy_part2().
Handle this by setting the return value to 0, in case HW restart is
in progress.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When HW restart is requested but not started yet, commands would not
be sent to the FW, and some function calls return an error. Such cases
can trigger unneeded warning messages, e.g., in iwl_mvm_mac_sta_state()
and iwl_mvm_bss_info_changed_station().
Handle a couple of these cases by also checking in the WARN_ON()
condition that HW restart is not requested.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The size of the buffer is IWL_FW_TRIGGER_ID_NUM - 1 which is equal to
IWL_FW_TRIGGER_ID_HOST_CHANNEL_SWITCH_COMPLETE so if the driver receives
this trigger, it will cause a buffer overflow.
Solve this by increasing the buffer size by 1.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: fe1b7d6c28 ("iwlwifi: add support for triggering ini triggers")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The spatial reuse 4 words fields are fetched from the HE-SIGA
by the firmware and propagated to the driver through the
Rx info. This is useful to populate the radiotap header.
We were looking at the wrong place in the firmware data and
got bogus values. Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: bdf180c8d3 ("iwlwifi: mvm: change PHY data RX for HE radiotap")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Enable ignore consecutive trigger feature which allows to configure the
driver to skip consecutive triggers from the same type.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix several issues related to dump delay:
1. In legacy dump trigger, use stop_delay field instead of trig_dis_ms.
2. ini delay is messured in usec so align both ini and legacy to usec.
3. schedule_delayed_work receives the delay value in jiffies so
translate the dump delay to jiffies.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: ea7cb82938 ("iwlwifi: dbg: make trigger functions type agnostic")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't support A-step for some device combinations anymore. So
change them to use B-step, renaming and reorganizing the config
structures. Additionally, fix one device that was using the wrong
configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add debug prints for FTM results info. These prints are used by
tests automation.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In HE-TB PPDUs (labeled HE-TRIG in radiotap), we were overwriting
the data4.spatial_reuse_1 field with the spatial reuse data that
the firmware gives us for SU/MU PPDUs. Fix that by moving that,
we are already setting the data4.spatial_reuse_{1,2,3,4} fields
in the TB PPDU case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 69f3ca8ed3 ("iwlwifi: mvm: show more HE radiotap data for TB PPDUs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FTM new API uses API TLV bit 15. The driver mistakenly uses
this bit for beacon filter API, although no TLV was assigned for
the beacon filter API. For now, make beacon filter use bit 16
instead (not set by the fw anyway). Once a TLV is assigned to the
beacon filter API it should be updated.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- The FW supports up to 4 concurrent scans, so adjust the definitions
accordingly.
- Only a single periodic scan is supported, so enforce it in the code.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
D3 debug data is disabled by default. Currently it is done by tampering
the dump mask. Add an operation that will allow this to be changed
without recompilation.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For AX210 devices, the periphry for forcing NMI
has changed.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AX210 family, UMAC periphery address space moved from
0xA00000 to 0xD00000.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Many periphery addresses have changed in AX210 devices.
Until sorting out which peripheries should be dumped, skip
that step for now.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In low power modes, the chip clock source for platform integrated
devices is 32kHz. It is generated internally and supplied by a crystal
oscillator. However using a 32kHz sourced from crystal oscillator
has high power penalty.
There is an option to get an external 32kHz clock from the platform. Past
experience shows that the reliability is platform dependent,
i.e. on some platforms it works good and on other it doesn’t.
Working from external clock will save 0.5 mW in sleep state, from overall
1.8mW that we have today, i.e. almost 30%.
Each OEM can enable or disable the use of the external 32kHz clock by
setting a BIOS configuration. In case the OEM configured to use 32kHz
external clock the driver will pass this indication to the FW.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When flushing TX queues no new TX should go into the system.
However, in the following scenario we get TX:
1. Queues are stopped and there are packets in overflow queue
2. Station is removed and flush begins
3. Flush empties space, and reclaim path TXes SKB from overflow
queue.
Note that the fact the queues are stopped during the process
doesn't matter - the packet will be TXed since the TX path
doesn't care if TX queues are stopped or not, just if there is
space in the queue, which there is, since we just freed a
packet.
A fix here is rather complicated, since the flow is very racy.
Change code not to warn if we are TXing from overflow TX.
In case there is TX from both overflow TX and TX path we will
miss a warning we optimally had, but we can live with that.
Make sure we don't return before overflow queue is empty, otherwise
we will think queues are empty, but they will be refilled, resulting
with assert.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 3955525d5d ("iwlwifi: pcie: buffer packets to avoid overflowing Tx queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Start supporting API version 46 where applicable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_mvm_te_clear_data() is called for cleanup in case sending
the HOT_SPOT_CMD failed. However, in case sending the command
caused a fw error and restart (e.g. if the command is not supported)
then the te_data pointer may no longer be valid, which leads to
a NULL pointer dereference.
Fix it by checking that the te_data pointer is not NULL before
dereferencing it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Until supporting UHB (ultra high band) channels for
devices AX210, do not fail if number of channels reported
by firmware is greater than NL80211_MAX_SUPP_REG_RULES.
The Driver in that case will use only the non-UHB channels.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new API and TLV for the ability to send commands in the beginning
and end of reset flow.
The full flow of recovery is:
1. While loading FW, get address (from the TLV) of target buffer
to read in case of reset
2. If an error/assert happens read the address data from step 1.
3. Reset the HW and load the FW.
4. Send the data read in step 2.
5. Add station keys
6. Send notification to FW that reset flow is done.
The main use of the recovery flow is for support in PN/SN recovery
when offloaded
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new device family AX210.
Make the needed changes for this family.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trigger field ignore_default was changed to override_trig.
The first byte of the field indicates the driver to override existing
configuration or keep the previous one
The second byte of the field indicated the driver to replace the regions
of the previous trigger or to append new regions to it.
Change the way the active triggers are maintained to support trigger
override in different apply points.
Do this by making a trigger that updates at runtime by the
triggers that are being used in the different apply points.
In case of an assert, the driver does not reconfigure the triggers
and uses the old configuration which leads to undefined behavior.
Solve this by clearing the triggers in assert recovery flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TLV 54 holds umac debug related addresses.
TLV 55 holds lmac debug related addresses.
These TLVs aim to replace the alive notification data in the future.
Parse and keep error table addresses received from the TLVs
for both lmac and umac and use these addresses instead of the pointer
received from alive notification.
The feature supports only unified image.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We now no longer have any special code in
iwl_mvm_pass_packet_to_mac80211(), so don't
need to pass NO_PSDU packets through it.
Stop doing so and clean up the code there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.
Additionally, add two defines we depend on in
include/linux/ieee80211.h.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for FTM responder for hardware/firmware combinations
that advertise support for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement monitor dram memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
WOWLAN images in unified firmwares should not be used, so don't require
them to support wowlan. This will allow to reduce the firmware's file
size.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement monitor sram memory dump in the new dump mechanism.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently there is no way to debug RX/TX paths using prints
without harming tpt. Add prints to debug RX allocation path.
We can still get 1.9 gbps with those on.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use IWL_DL_FW instead. This will free a bit for more
needed prints in newer devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allocator swaps the pending requests with 0 when it starts
working. This means that relying on it n RX path to decide if
to move to emergency is not always a good idea, since it may
be zero, but there are still a lot of unallocated RBs in the
system. Change allocator to decrement the pending requests on
real time. It is more expensive since it accesses the atomic
variable more times, but it gives the RX path a better idea
of the system's status.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 868a1e863f ("iwlwifi: pcie: avoid empty free RB queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of copying fields one by one copy the whole structure. This way there's
no need to modify the function every time we add a new field to the struct.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With W=1 there's a warning:
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'new' not described in 'ath10k_wow_convert_8023_to_80211'
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'old' not described in 'ath10k_wow_convert_8023_to_80211'
Fix it by changing the documentation marker '/**' to a normal code comment.
While at it, clean up the line wrapping.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With W=1 GCC warns:
drivers/net/wireless/ath/ath10k/htt.h:1746:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_32' is less than 4 [-Wpacked-not-aligned]
drivers/net/wireless/ath/ath10k/htt.h:1753:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_64' is less than 4 [-Wpacked-not-aligned]
Fix that by using __align(4). Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When adding a new value to enum wmi_service it's very easy to miss that the new
value should be also added to wmi_service_name() mapping function. Modify the
function so that GCC can now warn about this:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_FOO' not handled in switch [-Wswitch]
And also add a reminder to the enum.
Thanks to Jouni Malinen for the idea.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After implementing the next patch GCC reported:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BTCOEX' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_MGMT_TX_WMI' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_SPOOF_MAC_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_THERM_THROT' not handled in switch [-Wswitch]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If supported, update transmit airtime in mac80211 with the airtime
values reported by the firmware. TX airtime of the PPDU is reported
via HTT data TX completion indication message.
A new service flag 'WMI_SERVICE_REPORT_AIRTIME' is added to advertise
the firmware support. For firmwares which do not support this feature,
TX airtime is calculated in the driver using TX bitrate.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.6.1-00841
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast/broadcast traffic destined for a particular vlan group will
always be encrypted in software. To enable dynamic VLANs, it requires
driver support for sending software encrypted packets.
In ath10k, sending software encrypted frames is allowed only when we insmod
the driver with cryptmode param set to 1, this configuration disables
hardware crypto and enables RAW mode implicitly. Since, enabling raw
mode has performance impact, this cannot be considered as an ideal
solution for supporting VLANs in the driver.
As an alternative take, in this approach, cryptographic keys for
unicast traffic (per peer PTKs) and keys for non-vlan group traffic
will be configured in hardware, allowing hardware encryption for unicast
and non-vlan group traffic. Only vlan group traffic will be encrypted in
software and pushed to the target with encap mode set to RAW in the TX
descriptors.
Not all firmwares can support this type of key configuration(having few
keys installed in hardware and few only in software); for this purpose a
new WMI service flag "WMI_SERVICE_PER_PACKET_SW_ENCRYPT" is introduced to
advertise this support.
Also, adding the logic required to send sw encrypted frames in raw mode.
Hardwares Tested : QCA9984, QCA988X
Firmwares Tested : 10.4-3.5.3-00057, 10.2.4-1.0-00042
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure fine timing measurement (FTM) responder role from the
ftm_responder bss param sent by mac80211. With FTM functionality offloaded
to firmware, adding the interface allows userspace to enable or disable
FTM responder functionality. ath10k disables it at the time of interface
creation.
Supported FW: 10.4
Tested on IPQ4019 with firmware: 10.4-3.2.1.1-00022
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The airtime of a transmitted frame will be estimated from last used tx rate
which the firmware reports with the peer stats feature
(WMI_SERVICE_PEER_STATS). The airtime is computed on the tx path and it
will be reported to mac80211 upon tx completion.
This change is based on Kan's orginal commit in Chromium tree
("CHROMIUM: ath10k: Implementing airtime fairness based TX scheduler")
ref: https://chromium-review.googlesource.com/588190
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Signed-off-by: Kan Yan <kyan@google.com>
[rmanohar@codeaurora.org: ported only the airtime computation]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[toke@redhat.com: Rebase to mac80211-next, add test note]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k maintains common txqs list for all stations. This txq
management can be removed by migrating to mac80211 txq APIs
and let mac80211 handle txqs reordering based on reported airtime.
By doing this, txq fairness maintained in ath10k i.e processing
N frames per txq is removed. By adapting to mac80211 APIs,
ath10k will support mac80211 based airtime fairness algorithm.
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Tested-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves the ath9k driver to use the mac80211 TXQ scheduling and
airtime accounting APIs, removing the corresponding state tracking
inside the driver.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
[rmanohar@codeaurora.org: fixed checkpatch error and warnings]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 750afb08ca ("cross-tree: phase out dma_zalloc_coherent()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/ce.c:1602: line over 90 characters
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports shadow registers write operation support
for copy engine for regular operation in powersave mode.
Since WCN3990 is a 64-bit target, the shadow register
implementation needs to be done in the copy engine handlers
for 64-bit target. Currently the shadow register implementation
is present in the 32-bit target handlers of copy engine.
Fix the shadow register copy engine write operation
implementation for 64-bit target(WCN3990).
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: b7ba83f7c4 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
