There's no need to build a bitmap first and then iterate,
just do the iteration with the right locking directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to have a hw refcount if we just mark the
command queue with a (fake) TID; at that point, the refcount
becomes equivalent to the hweight() of the TID bitmap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
None of these functions really need to be separate, they're all
only used in sta.c, move them there and make them static.
Fix a small typo in related code while at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make this a named struct rather than an anonymous one,
we'll want to refer to it by name later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the rt status checking to the start of the resume flow in order
to avoid sending D0I3_END_CMD to the FW. Also, collect dump if an
assert was encountered.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Debug data dump is not working in flows that stop the device is used
in their error handling. During these flows the op mode mutex is
locked until the device stops. Because of that, any assert generated
from the firmware can be handled only after the device already
stopped.
Since dumping cannot occour after stopping the device, split the the
dump function to two parts, Part that handles locking, and the part
that starts the actual dumping and call the second part in the op mode
stop device function.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently in case of DCM with P2P GO where BSS DTIM interval < 220 msec
the fw fails to allocate events for the P2P GO dtim due to long passive
scan events.
Fix this by requesting all scans in this scenario to be fragmented with
fast balance scan time settings. The only exception is in case
fragmented scan was planned to be set due to low latency or high
throughput reason, set the scan timing as planned.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fast balance scan is similar to SCAN_TYPE_MILD, but this scan is
fragmented and has shorter out of operating channel time,
and therefore better match low latency scenarios.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed. Note that RSC is sent separately in
a new command. This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for new trigger type, make iwl_fw_dbg_collect_desc
agnostic to the trigger structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For trigger-based PPDUs, most values aren't part of the HE-SIG-A
because they're preconfigured by the trigger frame. However, we
still have this information since we used the trigger frame to
configure the hardware, so we can (and do) read it back out and
can thus show it in radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the info type is MU, we still have the data from the TSF
overload words, so should decode that. When it's MU_EXT_INFO
we additionally have the SIG-B common 0/1/2 fields.
Also document the validity depending on the info type and fix
the name of the regular TB PPDU info type accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add send host command op to firmware runtime op struct to allow sending
host commands to the op mode from the fw runtime context.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change MCC update response API to be compatible with new FW API.
While at it change v2 which is not in use anymore to v3 and cleanup
mcc_update v1 command and response which is obsolete.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trigger dump collection if the alive flow fails, regardless of the
reason.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In mac80211, the default remains for HT, so set the limit to
HE for our driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For SU/SU-ER/MU PPDUs we have spatial reuse.
For those where it's relevant we also know the pre-FEC
padding factor, PE disambiguity bit, beam change bit
and doppler bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add information about the LDCP extra symbol segment to the HE
data when applicable (not for trigger-based PPDUs).
While at it, clean up the code for UL/DL a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This code gets shorter if it doesn't have to check all the
conditions, so move it to an appropriate place that has all
of them validated already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split the code out into a separate routine, and move that to be
called inside the previously introduced iwl_mvm_decode_he_phy_data()
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull some of the decoding of he_phy_data into a separate function so
we don't need to check over and over again if it's valid.
While at it, fix the UL/DL bit reporting to be for all but trigger-
based frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As detected by Luca during code review when I move this in the
next patch, the code here is putting the data into the wrong
field (flags1 instead of flags2). Fix that.
Fixes: e5721e3f77 ("iwlwifi: mvm: add radiotap data for HE")
Reported-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove a stray empty line, unbreak some lines that aren't
really that long, and move on variable setting into the
initializer to avoid initializing it twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is equivalent to checking he_phy_data != HE_PHY_DATA_INVAL,
which is already done in a number of places, so remove the extra
'overload' variable entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix a bug that happens in the following scenario:
1) suspend without WoWLAN
2) mac80211 calls drv_stop because of the suspend
3) __iwl_mvm_mac_stop deallocates the aux station
4) during drv_stop the firmware crashes
5) iwlmvm:
* sets IWL_MVM_STATUS_HW_RESTART_REQUESTED
* asks mac80211 to kick the restart flow
6) mac80211 puts the restart worker into a freezable
queue which means that the worker will not run for now
since the workqueue is already frozen
7) ...
8) resume
9) mac80211 runs ieee80211_reconfig as part of the resume
10) mac80211 detects that a restart flow has been requested
and that we are now resuming from suspend and cancels
the restart worker
11) mac80211 calls drv_start()
12) __iwl_mvm_mac_start checks that IWL_MVM_STATUS_HW_RESTART_REQUESTED
clears it, sets IWL_MVM_STATUS_IN_HW_RESTART and calls
iwl_mvm_restart_cleanup()
13) iwl_fw_error_dump gets called and accesses the device
to get debug data
14) iwl_mvm_up adds the aux station
15) iwl_mvm_add_aux_sta() allocates an internal station for
the aux station
16) iwl_mvm_allocate_int_sta() tests IWL_MVM_STATUS_IN_HW_RESTART
and doesn't really allocate a station ID for the aux
station
17) a new queue is added for the aux station
Note that steps from 5 to 9 aren't really part of the
problem but were described for the sake of completeness.
Once the iwl_mvm_mac_stop() is called, the device is not
accessible, meaning that step 12) can't succeed and we'll
see the following:
drivers/net/wireless/intel/iwlwifi/pcie/trans.c:2122 iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]()
Timeout waiting for hardware access (CSR_GP_CNTRL 0x080403d8)
Call Trace:
[<ffffffffc03e6ad3>] iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]
[<ffffffffc03e6a13>] iwl_trans_pcie_dump_regs+0x3fd/0x3fd [iwlwifi]
[<ffffffffc03dad42>] iwl_fw_error_dump+0x4f5/0xe8b [iwlwifi]
[<ffffffffc04bd43e>] __iwl_mvm_mac_start+0x5a/0x21a [iwlmvm]
[<ffffffffc04bd6d2>] iwl_mvm_mac_start+0xd4/0x103 [iwlmvm]
[<ffffffffc042d378>] drv_start+0xa1/0xc5 [iwl7000_mac80211]
[<ffffffffc045a339>] ieee80211_reconfig+0x145/0xf50 [mac80211]
[<ffffffffc044788b>] ieee80211_resume+0x62/0x66 [mac80211]
[<ffffffffc0366c5b>] wiphy_resume+0xa9/0xc6 [cfg80211]
The station id of the aux station is set to 0xff in step 3
and because we don't really allocate a new station id for
the auxliary station (as explained in 16), we end up sending
a command to the firmware asking to connect the queue
to station id 0xff. This makes the firmware crash with the
following information:
0x00002093 | ADVANCED_SYSASSERT
0x000002F0 | trm_hw_status0
0x00000000 | trm_hw_status1
0x00000B38 | branchlink2
0x0001978C | interruptlink1
0x00000000 | interruptlink2
0xFF080501 | data1
0xDEADBEEF | data2
0xDEADBEEF | data3
Firmware error during reconfiguration - reprobe!
FW error in SYNC CMD SCD_QUEUE_CFG
Fix this by clearing IWL_MVM_STATUS_HW_RESTART_REQUESTED
in iwl_mvm_mac_stop(). We won't be able to collect debug
data anyway and when we will brought up again, we will
have a clean state from the firmware perspective.
Since we won't have IWL_MVM_STATUS_IN_HW_RESTART set in
step 12) we won't get to the 2093 ASSERT either.
Fixes: bf8b286f86 ("iwlwifi: mvm: defer setting IWL_MVM_STATUS_IN_HW_RESTART")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The triplet of get trigger, is trigger enabled and is trigger stopped
repeats itself. Group them in a function to avoid code duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow the FW to reorder HB channels and first scan HB channels with
assumed APs, in order to reduce the scan duration.
Currently enable it for all scan requests types.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The debug variables are bloating the iwl_fw struct. And the fields
are out of order, missing docs and some are redundant.
Clean this up. This serves as preparation for unionizing it for the
new ini infra.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When reading the profiles from the EWRD table in ACPI, we loop over
the data and set it into our internal table. We use the number of
profiles specified in ACPI without checking its validity, so if the
ACPI table is corrupted and the number is larger than our array size,
we will try to make an out-of-bounds access.
Fix this by making sure the value specified in the ACPI table is
valid.
Fixes: 6996490501 ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbs6LVAAoJEG4XJFUm622b0sAH/1WLU433ZipgULs6PLULDz3/
cFS4CSu9+Hewx9MKvdr+vgMoru70CkiFIZMJeo/oNqAtFb6TQhXPFz2Ci3K4Y6jK
yZKATh9PvzQrOGQ1iy4p8QK6bQ9WRUNY5+elJuNQH62oB/SZ0XqCMU8ujUQRSaTC
xVqfIRnAtKcchAm/nqxx+EwlGCiUmlyt2pw2IUXXABLW7Fkj3Z3ISlOd8xVW6tca
XyWlx9pjZOrFrgOzyORB/B4TNI5q5CdcYPg2DEpqOs6LQeGXEq4BSxfxCe2de4ku
St6417K0OFTbUTZS7kJaxJnQFd1ZWhDtj5cJUzdNsSVzqeYeJoTnR4FBqDWLlec=
=7Nmq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for setting keys for TKIP cipher suite was mistakenly removed
for AP mode. Fix this.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As a temporary stage in the 22560 devices bring up, we disabled
power save, to avoid bugs related to that domain.
Now we would like to use power save so enable the balanced mode,
and allow configuring the mode via module parameter.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We no longer want to consider the RSSI if the beacon / probe
has been heard on an adjacent channel.
This was based on a firmware capability that is now
unavailable.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new coex schema requires setting the non-shared antenna
for the single_stream_ant_msk field in the TLC command.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When operating as a soft ap with wep security, the key was not
configured to the fw for the stations, based on the fact that the
key will be specified in the tx command.
However, in the new tx api the tx command does not include the key,
which resulted in all data frames going out un-encrypted.
Fix it by configuring the key for all the stations as they are added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current FIFO size calculation is wrong for two reasons:
- We access lmac 0 by default
- We don't take 11ax into consideration.
Fix both.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since AMSDUs are not de-aggregated by HW in monitor mode,
we still need the option for setting large RBs (up to 12K).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make the adjustments for gen2 TX and RX of TKIP packets. Strip MIC on
RX. Don't add IV space and keep the MIC space zeroed on TX.
Devices that support gen2 data path support TKIP only in station mode.
In all other modes, fall back to SW encryption. Do this early in the
set_key() callback so that the key flags would not be incorrectly set.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to receive TB (Trigger Based) PPDU in monitor mode,
the Driver must send the HE_AIR_SNIFFER_CONFIG_CMD host command.
Enable that via debugfs.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
CDB support has nothing to do with non unified image.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Alexei's patch, assumed that all versions of "struct iwl_error_event_table"
are the same, but there are really different versions in different files.
Rather than trying to fix this, or splitting the tracepoint, or anything of
the sort, just remove it entirely - turns out that nobody really uses it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We already report the RU offset, so we'd better also
report that we know the value.
Fixes: e5721e3f77 ("iwlwifi: mvm: add radiotap data for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Check the actual bit (mask) in Rx notification rate_n_flags.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In new devices, access to periphery is forbidden. Send instead
host command to start and stop debugging.
Memory allocation is written in context info, but in case we
need to update it there is a dedicated command. Add definitions,
currently unused, of the new command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the restart FW debug code to a function. This avoids code
duplication and lays the infra to support the new start and stop
host commands in some future devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align to new 11ax draft D3.0. Change/add new MAC and PHY capabilities
and update drivers' 11ax capabilities and mac80211's debugfs
accordingly.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of fragmented scan on the HB channels, configure EBS to be
fragmented as well.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support more txq_alloc command types by moving the command declaration
to the gen specific area. While at it, move some of the code segments
to a common place for re-use.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Decode the HE TB PPDU data that we get in sniffer mode
and use it to populate the HE radiotap information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add flags to the tlc_cfg_cmd for signaling peer support for receiving
Dual Carrier Modulation at BPSK (MCS 0), and set them according to peer
capabilities.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the HE phy capabilities IE there are 2 bits to signal support for
STBC in bandwidths of 80Mhz or less, and of 160Mhz.
Use these bits to determine STBC support if this IE exists.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make all FW debug data stop recording flows to use
iwl_fw_dbg_stop_recording function instead of writing to FW
registers directly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As with the non-offloaded rs case, during assoc on the ap side the phy
context is set to 20MHz until authorization of a client that supports
wider channel-widths. Support this by sending the initial
tlc_config_cmd with max supported channel width of 20MHz until
authorization succeeds.
Fixes: 6b7a5aea71 ("iwlwifi: mvm: always init rs with 20mhz bandwidth rates")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Probe responses were sent to the multicast station while
they should be routed to the broadcast station.
This has no negative effect since the frame was still
routed to the right queue, but it looked very fishy
to send a frame to a (queue, station) tuple where
'queue' is not mapped to 'station'.
Fixes: 7c305de2b9 ("iwlwifi: mvm: Direct multicast frames to the correct station")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the bandwidth is only 20 MHz, then the second channel doesn't
exist, but the hardware reports the CRC was OK. Suppress the data
of the second channel in the HE radiotap in this case, by marking
it as not known.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is the same as for SU PPDUs, so it's easy to do.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The GI duration depends on the frame type in some cases,
take that into account when decoding for radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
I evidently completely confused "number of LTF symbols" and "LTF size".
Radiotap was reporting the former, while I thought it was the latter,
and we really need both.
Add the LTF symbol size into the newly defined field in radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement the extended HE-MU info type decoding to show the HE-SIG-B
common contents in the HE-MU radiotap field.
The DW4 data is partially overwritten by the hardware in all cases, so
only the higher 16 bits can be used. To be able to use it for the HE
SIG-B common data anyway, move the bits around in the following way:
SIG-B common 0: DW 4 -> DW 7
SIG-B common 1: DW 7 -> DW 8
SIG-B common 2: DW 8 -> DW 4 (upper half)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present. Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The parameter that indicated whether the LQ command should be sent
as sync or async was removed, causing the LQ command to be sent as
sync from interrupt context (e.g. from the RX path). This resulted
in a kernel warning: "scheduling while atomic" and failing to send
the LQ command, which ultimately leads to a queue hang.
Fix it by adding back the required parameter to send the command as
sync only when it is allowed.
Fixes: d94c5a820d ("iwlwifi: mvm: open BA session only when sta is authorized")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we receive TX response, we may release a few packets
due to a hole that was closed in the transmission window.
However, if that frame failed, we will mark all the released
frames as failed and will send multiple BARs.
This affects statistics badly, and cause unnecessary frames
transmission.
Instead, mark all the following packets as success, with the
desired result of sending a bar for the failed frame only.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a bug in FW where the sequence control may be
incorrect, and the driver overrides it with the value
of the ieee80211 header.
However, in BAR there is no sequence control in the header,
which result with arbitrary sequence.
This access to an unknown location is bad and it makes the
logs very confusing - so fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the NIC is disconnected, we just can't do anything
besides seeking for help from the bus driver. Dumping the
device's memory is not necessary and just bloats the logs
with unusable data. Moreover, asking mac80211 to restart
the hardware is also useless. Bypass all this.
Also, use the STATUS_TRANS_DEAD status bit instead of a
bool inside the transport layer. The advantage of this is
that now, the transport and the op_mode can know what is the
situation and bypass the useless recovery steps mentioned
above.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new coex schema requires moving to SISO only when BT AG is 4.
Adjust the SISO criteria according to the coex schema version reported
by firmware.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update reduce tx power command API to be compatible with new FW API.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While associated in low latency mode, or when traffic load is high,
don't enable EBS in scan request if fragmented EBS is not supported
by the FW.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The HE code is bloating the RX handling, and makes it too big.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The HE code is bloating the RX handling, and makes it too big.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current implementation turns this bit on only for HE MU.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A probe response built by a P2P GO should contain:
1. CSA/eCSA IE when relevant
2. If the corresponding probe request had P2P IE, then
need to add P2P IE with NOA attributes.
However, the NOA attributes and the updated channel switch
counter are known only to the FW. The solution is that FW
will send a notification with the relevant probe response
data and the driver will save it and update the probe
response accordingly.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A new FW API has been added for WOWLAN_GET_STATUSES to support
multiple GTK keys and IGTK keys. Check the respective TLV and use the
new API when it is set.
Let most of the code use the new version (v7) and convert the old
version (v6) to the new one when needed.
Also refactor some functions a bit so that they can be reused more
easily. Particularly the part that calls WOWLAN_GET_STATUSES which is
reused in D3 and D0i3.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Runtime PM can only be used if CONFIG_PM is set. Move all the d0i3
code (which is essentially runtime PM) behind the CONFIG_PM flag.
This prevents undefined usage of some functions when CONFIG_PM is not
defined.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We repeated the same if twice in a row. Remove the second one and
move the code block into the previous one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During d3, the firmware records debug data into internal buffer
if debug data collection occurs, collect the data that was written to the
buffer
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The tid for Non-QOS frames is set to IWL_MAX_TID_COUNT. This value
is also used for configuring the queue for non-QOS data. However, this
tid is used by the FW for management queues. As a result, the FW
does not encrypt non-QOS data frames.
Fix this by setting the tid for non-QOS data frames to zero, which
is a valid value for data frames in the FW.
This also fixes a bug in sending multicast frames, where the queues
are allocated with tid == 0, but are sent with tid == 8, which may
lead to unexpected behavior.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Balanced power save mode isn't supported in the fw for 22560 devices
yet. Configure the power save mode to CAM until it gets implemented.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit f2e66c8df0.
The firmware never implemented this, and they do not plan to.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently multi-queue is disabled for 22000 devices.
This was since driver isn't supposed to write to prph
registers anymore, and FW needs to configure the RFH.
Now that FW added support for the API - use it and remove
the 22000 multi RX queue disablement.
Bump min API version to avoid compatibility issues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the firmware does not stop recording debugging data when
entering D3 and this causes trouble (e.g. sporadic wake ups).
Fix that by stopping dbg recording when suspending.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reading and dumping memory areas takes time, and sometimes
dumping all of the areas isn't necessary.
Allow choosing the memory areas which should be dumped.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices use a new rx_mpdu_desc api.
Update the code to use the new api.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The smallest rb size supported today is 4k rx buffers.
22560 devices use 2k rxb's, so allow using 2k buffers.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices use a new tx cmd api. Update the code to use
the new api.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For devices which use the image loader image, the length of the frame
must be updated in the byte count in bytes, and not dwords as today.
Avoid dividing the input length by 4.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Device 22560 have many different hw and sw features than 22000 family,
so introduce a new family of devices - 22560.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a module parameter to disable 802.11ax features in supported
devices. This is useful for testing or if there are interoperability
issues with some APs.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in wireless-drivers by changing it to BIT_ULL instead. In addition, there are
some places which don't use BIT nor BIT_ULL macros so align those as well.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbD/3rAAoJEG4XJFUm622b1ZwH/1xe1IqcwJXzfoDsYPlXVnSh
TiLExjKkD0ty5M0//844FxpxE1sSYJKOJ11uz/COzyG2qi4+5lgpUdjnDoINuKfH
ycqrXGssW7ogPWkVvnxKtlEYvkHNRYLQtxvd26umT77C69jVJLD0x9uihhh2En/C
EKs+OK1Pp0SRvTfB4AblWzoAnpEe1wHJFFh4i3F5H0lMGxLQz/YjFl5aeAjjR406
0vSKLGy2wKIydp8Pe4cAqBEeUWDJurn8ufkk7bmAET5zaXTH1qgZzLH3OWtx/ksz
mcPQq9/ctv35G2917t3Sn69SIUCDGfYkP5DiZV+ti0Hz2gIV0zOg7mGYCU8uHaU=
=11X5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially in this code, the race didn't matter since it didn't
do anything. Latest with the commit I marked this as fixing it
started to matter as something got done here that needed other
data that got freed as soon as the queue notification wait was
returning.
In the scenario we saw, apparently the IWL_MVM_RXQ_NOTIF_DEL_BA
event was sent to all queues, but processing the last event we
returned from iwl_mvm_sync_rx_queues_internal() and then from
iwl_mvm_free_reorder() and continued some processing before
wl_mvm_del_ba() was even invoked on the other CPU. Thus, when
the latter finally ran, it found that mvm->baid_map[baid] was
no longer valid.
Correct the race by moving the counter decrement and wake_up()
to be done only after all the per-event processing completed.
Note that in the commit I marked as being fixed the wake_up()
didn't exist yet (and the code was otherwise problematic) but
this particular problem already existed in a way.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A peer can limit the number of subframes it can handle in a
single A-MSDU. Honor this limit.
Note that the smallest limit is 8, and we are very unlikely to reach
that limit. So this isn't really a big deal.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, a BA session is opened when the tx traffic exceeds
10 frames per second. As a result of inter-op problems with some
APs, add a condition to open BA session only when station is
already authorized.
Fixes: 482e48440a ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our hardware has a limited amount of buffer descriptors
for each Tx packet. Because of that, there is a short
piece of code that makes sure that that we don't push too
many subframes in an A-MSDU because of subframes needs 2
buffer descriptors. This code also takes into account the
number of fragment of the skb since we also need a buffer
descriptor for each fragment in the skb.
This piece of code though didn't check that the resulting
number of subframes wasn't 0.
A user reported that using NFS client, he could get skbs
that are so fragmented that the code mentioned above
returned 0 for the number of subframes making
skb_gso_segment fail and subconsequently iwlwifi would WARN.
Fix this by make sure that num_subframes is at least 1.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=199209
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some versions of the FW don't support channel switch in TDLS.
Add a condition that checks it.
Fixes: 307e47235a ("iwlwifi: mvm: configure TDLS peers to FW")
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In some cases we may get from FW errored frames with
UNKNOWN security type.
This may happen in unsecured aggregation flow, where
the first packet had a CRC error in the WEP bit, which
was followed by a failure to decrypt and was dropped.
The next frames in the aggregation "inherit" the bad metadata
of the first packet.
Make sure to drop such frames since RADA and other offloads
will not operate correctly which may have unexpected results.
In case of AP it also causes to TX AMSDU frames to the peers,
resulting with assert 0x104B.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are specific cases, such as SAE authentication exchange, that
might require long duration to complete. For such cases, add support
for indicating to the driver the required duration of the prepare_tx()
operation, so the driver would still be able to complete the frame
exchange.
Currently, indicate the duration only for SAE authentication exchange,
as SAE authentication can take up to 2000 msec (as defined in IEEE
P802.11-REVmd D1.0 p. 3504).
As the patch modified the prepare_tx() callback API, also modify
the relevant code in iwlwifi.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of "any" wowlan trigger is configured, no valid wakeup filter
was configured.
Moreover, the fw assumes there's no connection when there are no configured
wakeup filters.
This leads to the station info not being updated on D3 command, causing
rate_n_flags to be 0 when the offloading code sends tx frame (triggering
SYSASSERT_102C due to invalid antenna param)
Note: "any" trigger is currently assumed to only be used when entering
d0i3 (which has a different flow). However, we still reach this code
when using d3_test.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Firmware will only send non low-latency TIDs in the
bitmap, so the check is now redundant.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Future changes will require moving the HE radiotap data into
the SKB head, but this means we need to have the alignment
reservation done before that. To prepare, move the alignment
reservation earlier here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In future devices a new image will be introduced - IML. The IML, image
loader, is loaded by the ROM, and as part of the new self-init flow,
loads the rest of the firmware images to the device.
Store the image, so the ROM can load it to the device.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Different device families may have different flag values
for passing a message to the fw (i.e. SW_RESET).
In order to keep the code readable, and avoid conditioning
upon the family, store a value for each flag, which indicates
the bit that needs to be enabled.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To fix a conflict reported by Stephen Rothwell <sfr@canb.auug.org.au>:
Today's linux-next merge of the wireless-drivers-next tree got a
conflict in:
drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
between commit:
77e30e10ee ("iwlwifi: mvm: query regdb for wmm rule if needed")
from the wireless-drivers tree and commits:
9c4f7d5127 ("iwlwifi: move all NVM parsing code to the common files")
4c625c564b ("iwlwifi: get rid of fw/nvm.c")
from the wireless-drivers-next tree.
When trying to open aggregations on 22000 HW before
traffic had actually passed, the driver will discover
it is missing a queue to aggregate on. In such a case -
allocate a queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's already an opmode common file for nvm iwl-nvm-parse.c
Move the content of fw/nvm.c to iwl-nvm-parse.c and delete fw/nvm.c.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update rs-fw API to match changes in FW. Specifically, the
TLC_MNG_NOTIF_REQ_CMD command and TLC_MNG_AMSDU_ENABLE_NOTIF
notification are removed, the A-MSDU related info is received from FW
via the TLC_MNG_UPDATE_NOTIF, and the TLC_MNG_CONFIG_CMD uses version
2 of its data structure.
Additionally, constify some arguments in a couple of functions.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22000 devices rely on this flag to install the key to the right
queues. For earlier devices we didn't have a key / queue mapping and
the key was sent along with the Tx command for each Tx hence the
problem didn't arise.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This saves some typing and is overall more readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move all the NVM file handling code to iwl-nvm-parse.c where all this
stuff belongs. This cleans up the MVM specific code and allows easier
reuse by other opmodes if needed.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22000 devices, aka gen2, the TFS is 256 bytes.
In order to save memory, use shorter TX queue for aux and
mgmt queues, since there isn't much traffic on them.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for dynamic queue sizing, add a parameter
of the TX queue size to the dynamic queue allocation op
mode API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support the new APIs and activate AMSDU based on the
offloaded TLC decisions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code that sets the correct out-of-channel priority depending on
the scan type was accidentally removed during a rebase. Add it back.
Fixes: c1a7515393 ("iwlwifi: mvm: add adaptive dwell support")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Introduce and use iwl_mvm_cdb_scan_api(), which checks the family.
Most of this will go away once the 22000 firmware supports adaptive
dwell, after which the V6 scan API won't be used, but the V3 scan
*config* API will still need to be distinguished.
In any case, this gets rid of the completely bogus has_new_tx_api()
checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Detect low latency and traffic load per band. Add support for
deciding on scan type and timings per band.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Try to detect that the AP is not using aggregation even when there's
enough traffic to make it worthwhile; if this is the case and U-APSD
is enabled then assume the AP is broken (like so many) and doesn't
enable aggregation when U-APSD is used. In this case, disconnect from
the AP and blacklist U-APSD for a potential new connection to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The primary channel is the channel that will be untouched by BT. The
secondary channel might be touched by BT. Hence, we want the primary
to be the most active channel. To do so, use the TCM infrastructure.
Since the BT keeps sending notifications, we can rely on them to
trigger the check. Every 10 seconds, we will check what is the most
active context and chose the right primary.
We need to wait 10 seconds before we modify the settings because
frequent changes in these settings can confuse BT.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code for changing the scan priority is already implemented, but
isn't yet in use. Now that TCM data is available, we can base the
scan priority decision on the traffic load.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Traffic condition monitor gathers data about the traffic load and
other conditions and can be used to make decisions regarding latency,
throughput etc. This patch introduces the code and data structures to
collect this data for future use.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since our device is regulatory self managed it maintains its regulatory
rules by its own. However the wmm_rules values can't be set by the
device itself but only the indication about the need to set it.
In case the device set wmm indication, proactively query the regulatory
data base to get these values
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-03-31
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add raw BPF tracepoint API in order to have a BPF program type that
can access kernel internal arguments of the tracepoints in their
raw form similar to kprobes based BPF programs. This infrastructure
also adds a new BPF_RAW_TRACEPOINT_OPEN command to BPF syscall which
returns an anon-inode backed fd for the tracepoint object that allows
for automatic detach of the BPF program resp. unregistering of the
tracepoint probe on fd release, from Alexei.
2) Add new BPF cgroup hooks at bind() and connect() entry in order to
allow BPF programs to reject, inspect or modify user space passed
struct sockaddr, and as well a hook at post bind time once the port
has been allocated. They are used in FB's container management engine
for implementing policy, replacing fragile LD_PRELOAD wrapper
intercepting bind() and connect() calls that only works in limited
scenarios like glibc based apps but not for other runtimes in
containerized applications, from Andrey.
3) BPF_F_INGRESS flag support has been added to sockmap programs for
their redirect helper call bringing it in line with cls_bpf based
programs. Support is added for both variants of sockmap programs,
meaning for tx ULP hooks as well as recv skb hooks, from John.
4) Various improvements on BPF side for the nfp driver, besides others
this work adds BPF map update and delete helper call support from
the datapath, JITing of 32 and 64 bit XADD instructions as well as
offload support of bpf_get_prandom_u32() call. Initial implementation
of nfp packet cache has been tackled that optimizes memory access
(see merge commit for further details), from Jakub and Jiong.
5) Removal of struct bpf_verifier_env argument from the print_bpf_insn()
API has been done in order to prepare to use print_bpf_insn() soon
out of perf tool directly. This makes the print_bpf_insn() API more
generic and pushes the env into private data. bpftool is adjusted
as well with the print_bpf_insn() argument removal, from Jiri.
6) Couple of cleanups and prep work for the upcoming BTF (BPF Type
Format). The latter will reuse the current BPF verifier log as
well, thus bpf_verifier_log() is further generalized, from Martin.
7) For bpf_getsockopt() and bpf_setsockopt() helpers, IPv4 IP_TOS read
and write support has been added in similar fashion to existing
IPv6 IPV6_TCLASS socket option we already have, from Nikita.
8) Fixes in recent sockmap scatterlist API usage, which did not use
sg_init_table() for initialization thus triggering a BUG_ON() in
scatterlist API when CONFIG_DEBUG_SG was enabled. This adds and
uses a small helper sg_init_marker() to properly handle the affected
cases, from Prashant.
9) Let the BPF core follow IDR code convention and therefore use the
idr_preload() and idr_preload_end() helpers, which would also help
idr_alloc_cyclic() under GFP_ATOMIC to better succeed under memory
pressure, from Shaohua.
10) Last but not least, a spelling fix in an error message for the
BPF cookie UID helper under BPF sample code, from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
fix iwlwifi_dev_ucode_error tracepoint to pass pointer to a table
instead of all 17 arguments by value.
dvm/main.c and mvm/utils.c have 'struct iwl_error_event_table'
defined with very similar yet subtly different fields and offsets.
tracepoint is still common and using definition of 'struct iwl_error_event_table'
from dvm/commands.h while copying fields.
Long term this tracepoint probably should be split into two.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently we have a boolean variable for each cause.
This costs space, and requires to check each separately
when determining low latency.
Since we have another cause incoming, convert it to an enum.
While at it, move the retrieval of the prev value and the
assignment of the new value to be inside iwl_mvm_update_low_latency
and save the need for each caller to do it separately.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove fragmented_dwell_time and add num_of_fragments to support
the new API version.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW does not allocate quota air time for the binding of a station
MAC before iwlmvm indicates that it is associated. Currently iwlmvm
indicates that the MAC is associated only after hearing a beacon from
the AP. In case a deauthentication frame is sent before the MAC is
associated, the frame might not be sent as the corresponding binding
is not scheduled.
To handle such cases, set IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP in the
HW flags, requesting mac80211 to call the mgd_prepare_tx() callback
before transmitting a deauthentication frame if associated but no
beacon was heard from the AP.
In addition, do not warn in iwl_mvm_mac_mgd_prepare_tx() when already
associated as now the callback can be called also when associated.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for Optimized Connectivity Experience (OCE). Get
capabilities from the fw, expose them with nl80211, and enable them in
UMAC scan if the relevant nl80211 flags are set by the userspace.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update the scan command API with support for adaptive dwell. Adaptive
dwell is a type of scan that dynamically changes the time it remains
on each channel listening for beacons or probe responses.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes iwl_mvm_disable_txq() may be called with mac80211_queue ==
IEEE80211_INVAL_HW_QUEUE, and this would cause us to use BIT(0xFF)
which is way too large for the u16 we used to store it in
hw_queue_to_mac820211. If this happens the following UBSAN warning
will be generated:
[ 167.185167] UBSAN: Undefined behaviour in drivers/net/wireless/intel/iwlwifi/mvm/utils.c:838:5
[ 167.185171] shift exponent 255 is too large for 64-bit type 'long unsigned int'
Fix that by checking that it is not IEEE80211_INVAL_HW_QUEUE and,
while at it, add a warning if the queue number is larger than
IEEE80211_MAX_QUEUES.
Fixes: 34e10860ae ("iwlwifi: mvm: remove references to queue_info in new TX path")
Reported-by: Paul Menzel <pmenzel+linux-wireless@molgen.mpg.de>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes future bail-outs from transmitting an AMSDU more
readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When immediate quiet bit is set in CSA, the entire channel is blocked
by the firmware. It is expected that all the MACs will evacuate the
channel and the phy will be eventually either moved or removed.
Currently, the phy context is just unreferenced and thus, the quiet
bit is kept set and it will be impossible to TX on this phy, if we
will need to reuse it in the future. This can be seen when doing a
channel switch with mode=1 (quiet) twice from channel X to Y and then
back to channel X.
Fix that, by moving the phy context to a default channel when not
referenced anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When starting aggregation, the code checks the status of the queue
allocated to the aggregation tid, which might not yet be allocated
and thus the queue index may be invalid.
Fix this by reserving a new queue in case the queue id is invalid.
While at it, clean up some unreachable code (a condition that is
already handled earlier) and remove all the non-DQA comments since
non-DQA mode is no longer supported.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the driver failed to resume from D3, it is possible that it has
no valid aux station. In such case, fw restart will end up in sending
station related commands with an invalid station id, which will
result in an assert.
Fix this by allocating a new station id for the aux station if it
does not have a valid id even in the case of fw restart.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a queue is reserved for aggregation, the queue id is assigned
to the tid_data. This is fine since iwl_mvm_sta_tx_agg_oper()
takes care of allocating the queue before actual tx starts.
When the reservation is cancelled (e.g. when the AP declined the
aggregation request) the tid_data is not cleared. As a result,
following tx for this tid was trying to use an unallocated queue.
Fix this by setting the txq_id for the tid to invalid when unreserving
the queue.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After switching to a new channel, driver schedules session protection
time event in order to hear the beacon on the new channel.
The duration of the protection is two beacon intervals.
However, since we start to switch slightly before beacon with count 1, in
case we don't hear (or AP doesn't transmit) the very first beacon on the
new channel the protection ends without hearing any beacon at all.
At this stage the switch is not complete, the queues are closed and the
interface doesn't have quota yet or TBTT events. As the result, we are
stuck forever waiting for iwl_mvm_post_channel_switch() to be called.
Fix this by increasing the protection time to be 3 beacon intervals and
in addition drop the connection if the time event ends before we got any
beacon.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some devices use a shared clock which is very sensitive to variations
and cause trouble in some situations. We need to set a bit in the phy
configuration to indicate that to the FW. To make this generic, add a
extra_phy_config_flags element to the device configuration and OR it
into the phy_cfg before sending it to the firmware. And also create a
set of configurations for devices that use shared clocks and need this
extra bit to be set.
Fixes: c62446d2b0 ("iwlwifi: add new 9460 series PCI IDs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The earlier patch called the station add functions but didn't
assign their return value to the ret variable, so that the
checks for it were meaningless. Fix that.
Found by smatch:
.../mac80211.c:2560 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
.../mac80211.c:2563 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
Fixes: 3a89411cd31c ("iwlwifi: mvm: fix assert 0x2B00 on older FWs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently when an IGTK is set for an AP, it is set as a regular key.
Since the cipher is set to CMAC, the STA_KEY_FLG_EXT flag is added to
the host command, which causes assert 0x253D on NICs that do not support
this.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The tid being used for the queue (cab_queue) for the MCAST
station has been changed recently to be 0 (for BE).
The flush path still flushed only the special tid (15)
which means that the firmware wasn't flushing the right
queue and we could get a firmware crash upon remove
station if we had an MCAST packet on the ring.
The current code that flushes queues for a station only
differentiates between internal stations (stations that
aren't instantiated in mac80211, like the MCAST station)
and the non-internal ones.
Internal stations can be either: BCAST (beacons), MCAST
(for cab_queue), GENERAL_PURPOSE (p2p dev, and sniffer
injection). The internal stations can use different tids.
To make the code simpler, just flush all the tids always
and add the special internal tid (15) for internal
stations. The firmware will know how to handle this even
if we hadn't any queue mapped that that tid.
Fixes: e340c1a6ef4b ("iwlwifi: mvm: Correctly set the tid for mcast queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the scheduler config command, the meaning of tid == 0xf was intended
to indicate the configuration is for management frames. However,
tid == 0xf was also used for the multicast queue that was meant only
for multicast data frames, which resulted with the FW not encrypting
multicast data frames.
As multicast frames do not have a QoS header, fix this by setting
tid == 0, to indicate that this is a data queue and not management
one.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Multicast frames for NL80211_IFTYPE_AP and NL80211_IFTYPE_ADHOC were
directed to the broadcast station, however, as the broadcast station
did not have keys configured, these frames were sent unencrypted.
Fix this by using the multicast station which is the station for which
encryption keys are configured.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the GTK is installed, we install it to HW with the
station ID of the AP.
Mac80211 will try to remove it only after the AP sta is
removed, which will result in a failure to remove key
since we do not have any station for it.
This is a valid situation, but a previous commit removed
the early return and added a return with error value, which
resulted in an error message that is confusing to users.
Remove the error return value.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trying to collect firmware debug data while firmware
is not loaded causes various errors (e.g. failing NIC access).
This causes even a bigger issue if at that time the
HW radio is off.
In that case, when later turning the radio on, the Driver
fails to read the HW (registers contain garbage values).
(It may be that the CSR_GP_CNTRL_REG_FLAG_RFKILL_WAKE_L1A_EN
bit is cleared on faulty NIC access - since the same behavior
was seen in HW RFKILL toggling before setting that bit.)
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We should add the multicast station before adding the
broadcast station.
However, in older FW, the firmware will start beaconing
when we add the multicast station, and since the broadcast
station is not added at this point so the transmission
of the beacon will fail on assert 0x2b00.
This is fixed in later firmware, so make the order
of addition depend on the TLV.
Fixes: 26d6c16bed ("iwlwifi: mvm: add multicast station")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It was assumed that apply_time==0 implies immediate scheduling, which is
wrong. Instead, the fw expects the START_IMMEDIATELY flag to be set.
Otherwise, this resulted in 0x3063 assert.
Fix that.
While at it rename the T2_V2_START_IMMEDIATELY to
TE_V2_START_IMMEDIATELY.
Fixes: f5d8f50f27 ("iwlwifi: mvm: Fix channel switch in case of count <= 1")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't have enough room in the TX command for a CCMP 256
key, and need to use key from table.
Fixes: 3264bf032bd9 ("[BUGFIX] iwlwifi: mvm: Fix CCMP IV setting")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While entering to D3 mode there is a gap between the time the
driver handles the D3_CONFIG_CMD response to the time the host is going
to sleep.
In between there might be cases which MARKER_CMD can tailgate.
Also during resume flow the MARKER_CMD might get sent while D0I3_CMD
is being handled in the FW.
Cancel MARKER_CMD timer and set it again properly during suspend
resume flows to prevent this command from being sent accidentlly.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Canceling the periodic timestamp work should be
done in the opposite flow to where it was started.
This also prevents from sending the MARKER command
during the mac_stop flow - causing a false queue hang
(FW is no longer there to send a response).
Fixes: 93b167c13a ("iwlwifi: runtime: sync FW and host clocks for logs")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In IBSS, the mac80211 sets the cab_queue to be invalid.
However, the multicast station uses it, so we need to override it.
A previous patch did it, but it was nested inside the if's and was
applied only for legacy FWs that don't support the new station type
API, instead of being applied for all paths.
In addition, add a missing NL80211_IFTYPE_ADHOC to the initialization
of the queues in iwl_mvm_mac_ctxt_init()
Fixes: ee48b72211 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A previous patch allowed the same PN for packets originating from the
same AMSDU by copying PN only for the last packet in the series.
This however is bogus since we cannot assume the last frame will be
received on the same queue, and if it is received on a different ueue
we will end up not incrementing the PN and possibly let the next
packet to have the same PN and pass through.
Change the logic instead to driver explicitly indicate for the second
sub frame and on to be allowed to have the same PN as the first
subframe. Indicate it to mac80211 as well for the fallback queue.
Fixes: f1ae02b186 ("iwlwifi: mvm: allow same PN for de-aggregated AMSDU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This aligns the code with the existing pattern to check
if the firmware has a certain capability.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recently a new command was added to the firmware
for setting a MAC's low-latency mode. Use it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have TSO enabled, we might end up segmenting it and
queuing multiple packets before the queue is even enabled. This causes
a warning.
For example, when starting TCP traffic on a non-zero TID, the
first packets may not have DSCP and will be sent on TID 0, while
the actual data packets will be sent on the TID.
To prevent this, simply remove the warning.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Latest firmware calculates both phases of the TKIP
field, so the TTAK ok flag is not needed and deprecated.
Support this API change.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For sync we send a marker cmd every <defined throughout debugfs> seconds.
The trigger for getting gp2 clock values from the FW is set by
writing to debugfs a periodic time in seconds,
if value zero is written, only one request would be sent
and the timer would be canceled.
Also added a small infrastructure for debugfs runtime code.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The way p2p NoA is forced in SCM (used for WFA tests)
is by setting a quota < 100% (simulating DCM).
A test-mode command is used for setting the NoA params.
In that case, force quota update or nothing will happen
if there was no significant change in the quota
at that exact point (which is likely to be the case).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Most of the sw resets in the code are done by one function,
which writes to the relevant CSR.
Use the common function to perform the only reset which was
done separately, redundant to the common code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support internal debug data collection on 9000 and newer
devices.
The method for finding the base and end address has changed
on new HW's, so introduce a new version of debug destination
tlv.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaN8MiAAoJEG4XJFUm622bGN4H/jc7+JqGUMozK8CKe5UGFnu7
HlwP3Vpz7SR655CgoMzvNzJ6lvBxaPA77epPFkALuwua3J22feakv5UGipT7RPI/
EtFCtq6+dIB+qooJ/8hUQVfAV8o13+dQzBQqtp7Wg37ok0qhcGpTLsvf2rI0ZG1R
+lcC2Jyk0lYjAPuPri3+KjxPLkZhGbx/hCdKwxQfCoubEVoqimMcQ68+RqU3rxNB
Of2Sk8IsaIevantLPnmO0+9OhZiMyoy4QGSnnuHntdpgZqEl0NbmVshQONCU9oTu
3RPKvbbYe57gRfgLKEvqTvij5R8ZxxwF+BFacaXch7Q9k6pMoJuyD6gJ8/S8AW8=
=FTCb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
The drivers/net/wireless/intel/iwlwifi/pcie/drv.c conflict was
resolved using a diff provided by Kalle in his pull request.
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
A bigger pull request this time, the most visible change being the new
driver mt76. But there's also Kconfig refactoring in ath9k and ath10k,
work beginning in iwlwifi to have rate scaling in firmware/hardware,
wcn3990 support getting closer in ath10k and lots of smaller changes.
mt76
* a new driver for MT76x2e, a 2x2 PCIe 802.11ac chipset by MediaTek
ath10k
* enable multiqueue support for all hw using mac80211 wake_tx_queue op
* new Kconfig option ATH10K_SPECTRAL to save RAM
* show tx stats on QCA9880
* new qcom,ath10k-calibration-variant DT entry
* WMI layer support for wcn3990
ath9k
* new Kconfig option ATH9K_COMMON_SPECTRAL to save RAM
wcn36xx
* hardware scan offload support
wil6210
* run-time PM support when interface is down
iwlwifi
* initial work for rate-scaling offload
* Support for new FW API version 36
* Rename the temporary hw name A000 to 22000
ssb
* make SSB a menuconfig to ease disabling it all
mwl8k
* enable non-DFS 5G channels 149-165
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I accidentally pushed a patch with CPTCFG (which is used in the
backports project) to the rs-fw.c file. Fix that to use CONFIG
instead.
Fixes: 9f66a397c8 ("iwlwifi: mvm: rs: add ops for the new rate scaling in the FW")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When statistics are read from debugfs, make sure that they
are actually updated from the firmware.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If FW loads without a problem, leaving init_dbg on can
cause a confusion, since the user won't necessarily
remember it is still turned on, and there are flows in
which everything continues as usual, only without
stopping the device after INIT, even if there is no FW
assert. On 22000 HW, for instance, this causes a
warning, since the paging is getting initialized twice.
Solve the issue by making this module param effective
only if the FW indeed asserts during INIT.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When sending LQ command, verify the rate scaling is not in firmware.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch sends to the FW notification configuration command and
handles the update responses.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch adds rate scaling configuration command and
implements a few other handlers.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch introduces a new instance of rate_control_ops for
the new API (adding only empty stubs here and the subsequent
patches in the series will fill in the implementation).
The decision which API to use is done during the register
step according to FW TLV.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New devices will have rate scaling algorithm running in the firmware.
With this feature, the driver's responsiblity is to provide an initial
configuration and to handle notifications regarding recent rates and
some other parameters. Debugfs hooks will be still available for
reading the current rate/statistics and setting a fixed rate.
The old API is supported so far, though both APIs cannot be used
simultaneously.
This is the first patch in the series. It adds a new TLV specifying
FW support for the new API and updates lq_sta to support two types
of rate scaling.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We might erroneously get to error dumping code when the
device is already stopped.
In that case the driver will detect a defective value and will try to
reset the HW, assuming it is only a bus issue. The driver than
proceeds with the dumping.
The result has two side effects:
1. The device won't be stopped again, since the transport status is
already stopped, so the device remains powered on while it actually
should be stopped.
2. The dump in that case is completely garbaged and useless.
Detect and avoid this. It will also make debugging such issues
easier.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the removal of non-DQA code, we don't need the queues
variable any more. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the WFA vendor specific TPC report IE to probe requests
when it is not added by the FW. The FW will still need to set
the tx power field.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When RADA is active, the hardware decrypts the packets and strips off
the MIC as it is useless after decryption. Indicate that to mac80211.
Cc: stable@vger.kernel.org # 4.13+
[this is needed for the 9000-series HW to work properly]
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the flag that indicates that ICV was stripped on if
this option was enabled in the HW.
Cc: stable@vger.kernel.org # 4.13+
[this is needed for the 9000-series HW to work properly]
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Before deleting a time event (remain-on-channel instance), flush
the queue so that frames cannot get stuck on it. We already flush
the AUX STA queues, but a separate station is used for the P2P
Device queue.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
-----BEGIN PGP SIGNATURE-----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=j1dk
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
First batch of iwlwifi updates for v4.16
* Rename the temporary name A000 to 22000;
* Change in the way we print the firmware version;
* Remove some unused code;
* Other small improvements;
kvalo:
There were conflicts, I fixed them with taking into account commit c2c48ddfc8
("iwlwifi: fix firmware names for 9000 and A000 series hw"):
CONFLICT (content): Merge conflict in drivers/net/wireless/intel/iwlwifi/iwl-config.h
CONFLICT (modify/delete): drivers/net/wireless/intel/iwlwifi/cfg/a000.c deleted in ca495785063c428641cc6df8888afd2587ca6677 and modified in HEAD. Version HEAD of drivers/net/wireless/intel/iwlwifi/cfg/a000.c left in tree.
The family name A000 was just a place-holder when we didn't know what
the official name would be yet. Now we know that the family name is
22000, so rename all occurrences accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since iwl_mvm_start_p2p_roc() is only called from iwl_mvm_roc(),
which already flushes the same work item, doing it again in it
is superfluous. Remove it and move the comment to the first one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This feature was actually removed from firmware, but without
ever telling the driver. Since nobody is actually using it,
just remove it entirely without bothering with a capability
check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new API will not be used, remove the code that
supports it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we are in a search cycle, we try different combinations
of parameters. Those combinations are called 'columns'.
When we switch to a new column, we first need to check if
this column has a suitable rate, if not, we can't try it.
This means we must not erase the statistics we gathered
for the previous column until we are sure that we are
indeed switching column.
The code that tries to switch to a new column first sets
a whole bunch of things for the new column, and only then
checks that we can find suitable rates in that column.
While doing that, the code mistakenly erased the rate
statistics. This code was right until
struct iwl_scale_tbl_info grew up for TPC.
Fix this to make sure we don't erase the rate statistics
until we are sure that we can indeed switch to the new
column.
Note that this bug is really harmless since it causes a
change in the behavior only when we can't find any rate
in the new column which should really not happen. In the
case we do find a suitable we reset the rate statistics
a few lines later anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In A000 family, compressed BA notifs can include MGMT
frames, so don't fail RXs in such a case.
While at it, since in A000 the TID for MGMT frames is
15, treat it in the RX flow as if received TID 8. This
way we won't require special handling of this TID.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This bit will be used in CCK to indicate short preamble.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to have a station and a queue for the monitor
interface to be able to inject traffic. We used to have
this traffic routed to the auxiliary queue, but this queue
isn't scheduled for the station we had linked to the
monitor vif.
Allocate a new queue, link it to the monitor vif's station
and make that queue use the BE fifo.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196715
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MONITOR type is missing in the interface type switch.
Add it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we act as an AP, new firmware versions handle
internally the power saving clients and the driver doesn't
know that the peers went to sleep. It is, hence, possible
that a peer goes to sleep for a long time and stop pulling
frames. This will cause its transmit queue to hang which is
a condition that triggers the recovery flow in the driver.
While this client is certainly buggy (it should have pulled
the frame based on the TIM IE in the beacon), we can't blow
up because of a buggy client.
Change the current implementation to not enable the
transmit queue hang detection on queues that serve peers
when we act as an AP / GO.
We can still enable this mechanism using the debug
configuration which can come in handy when we want to
debug why the client doesn't wake up.
Cc: stable@vger.kernel.org # v4.13
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
ieee80211_rx_status::chains was always set to zero.
That caused rate scaling to always start with the
lowest rate possible (rs_get_initial_rate).
Set it correctly according to the MPDU response.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
-----BEGIN PGP SIGNATURE-----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=JPn9
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
iwlwifi: first set of fixes for 4.15
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
