We have always had softe in pt_regs, and accessible via PT_SOFTE, even
though it is not userspace state.
The value userspace sees should always be 1, because we should never
be in userspace with interrupts soft disabled.
In a subsequent patch we will be changing the semantics of the kernel
softe value, so hard wire the value to 1 to retain the existing
semantics. As far as we know nothing ever looks at it, but better safe
than sorry.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
[mpe: Split out of larger patch, write change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This works on top of the single escalation support. When in single
escalation, with this change, we will keep the escalation interrupt
disabled unless the VCPU is in H_CEDE (idle). In any other case, we
know the VCPU will be rescheduled and thus there is no need to take
escalation interrupts in the host whenever a guest interrupt fires.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The prodded flag is only cleared at the beginning of H_CEDE,
so every time we have an escalation, we will cause the *next*
H_CEDE to return immediately.
Instead use a dedicated "irq_pending" flag to indicate that
a guest interrupt is pending for the VCPU. We don't reuse the
existing exception bitmap so as to avoid expensive atomic ops.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The powerpc NMI IPIs may not be recoverable if they are taken in
some sections of code, and also there have been and still are issues
with taking NMIs (in KVM guest code, in firmware, etc) which makes them
a bit dangerous to use.
Generic code like softlockup detector and rcu stall detectors really
hammer on trigger_*_backtrace, which has lead to further problems
because we've implemented it with the NMI.
So stop providing NMI backtraces for now. Importantly, the powerpc code
uses NMI IPIs in crash/debug, and the SMP hardlockup watchdog. So if the
softlockup and rcu hang detection traces are not being printed because
the CPU is stuck with interrupts off, then the hard lockup watchdog
should get it with the NMI IPI.
Fixes: 2104180a53 ("powerpc/64s: implement arch-specific hardlockup watchdog")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Book3S PACA memory allocation is restricted by the RMA limit and also
must not take SLB faults when accessed in virtual mode. Currently a
fixed 256MB limit is used for this, which is imprecise and sub-optimal.
Update the paca allocation limits to use use the ppc64_rma_size for RMA
limit, and share the safe_stack_limit() that is currently used for stack
allocations that must not take virtual mode faults.
The safe_stack_limit() name is changed to ppc64_bolted_size() to match
ppc64_rma_size and some comments are updated. We also need to use
early_mmu_has_feature() because we are now calling this function prior
to the jump label patching that enables mmu_has_feature().
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Change mmu_has_feature() to early_mmu_has_feature()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Hypervisor maintenance interrupts (HMIs) are generated by various
causes, signalled by bits in the hypervisor maintenance exception
register (HMER). In most cases calling OPAL to handle the interrupt
is the correct thing to do, but the "debug trigger" HMIs signalled by
PPC bit 17 (bit 46) of HMER are used to invoke software workarounds
for hardware bugs, and OPAL does not have any code to handle this
cause. The debug trigger HMI is used in POWER9 DD2.0 and DD2.1 chips
to work around a hardware bug in executing vector load instructions to
cache inhibited memory. In POWER9 DD2.2 chips, it is generated when
conditions are detected relating to threads being in TM (transactional
memory) suspended mode when the core SMT configuration needs to be
reconfigured.
The kernel currently has code to detect the vector CI load condition,
but only when the HMI occurs in the host, not when it occurs in a
guest. If a HMI occurs in the guest, it is always passed to OPAL, and
then we always re-sync the timebase, because the HMI cause might have
been a timebase error, for which OPAL would re-sync the timebase, thus
removing the timebase offset which KVM applied for the guest. Since
we don't know what OPAL did, we don't know whether to subtract the
timebase offset from the timebase, so instead we re-sync the timebase.
This adds code to determine explicitly what the cause of a debug
trigger HMI will be. This is based on a new device-tree property
under the CPU nodes called ibm,hmi-special-triggers, if it is
present, or otherwise based on the PVR (processor version register).
The handling of debug trigger HMIs is pulled out into a separate
function which can be called from the KVM guest exit code. If this
function handles and clears the HMI, and no other HMI causes remain,
then we skip calling OPAL and we proceed to subtract the guest
timebase offset from the timebase.
The overall handling for HMIs that occur in the host (i.e. not in a
KVM guest) is largely unchanged, except that we now don't set the flag
for the vector CI load workaround on DD2.2 processors.
This also removes a BUG_ON in the KVM code. BUG_ON is generally not
useful in KVM guest entry/exit code since it is difficult to handle
the resulting trap gracefully.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of calling both of_irq_parse_pci() and irq_create_of_mapping(),
call of_irq_parse_and_map_pci(), which does the same thing. This will allow
making of_irq_parse_pci() a private, static function.
This changes the logic slightly in that the fallback path will also be
taken if irq_create_of_mapping() fails internally.
Signed-off-by: Rob Herring <robh@kernel.org>
[bhelgaas: fold in virq init from Stephen Rothwell <sfr@canb.auug.org.au>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Commit 177ba7c647 ("powerpc/mm/radix: Limit paca allocation in radix")
limited the paca allocation address to 1G on pSeries because RTAS return
accesses the paca in 32-bit mode:
On return from RTAS we access the paca variables and we have 64 bit
disabled. This requires us to limit paca in 32 bit range.
Fix this by setting ppc64_rma_size to first_memblock_size/1G range.
Avoid this limit by switching to 64-bit mode before accessing any memory.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are several cases outside the normal address space management
where a CPU's entire local TLB is to be flushed:
1. Booting the kernel, in case something has left stale entries in
the TLB (e.g., kexec).
2. Machine check, to clean corrupted TLB entries.
One other place where the TLB is flushed, is waking from deep idle
states. The flush is a side-effect of calling ->cpu_restore with the
intention of re-setting various SPRs. The flush itself is unnecessary
because in the first case, the TLB should not acquire new corrupted
TLB entries as part of sleep/wake (though they may be lost).
This type of TLB flush is coded inflexibly, several times for each CPU
type, and they have a number of problems with ISA v3.0B:
- The current radix mode of the MMU is not taken into account, it is
always done as a hash flushn For IS=2 (LPID-matching flush from host)
and IS=3 with HV=0 (guest kernel flush), tlbie(l) is undefined if
the R field does not match the current radix mode.
- ISA v3.0B hash must flush the partition and process table caches as
well.
- ISA v3.0B radix must flush partition and process scoped translations,
partition and process table caches, and also the page walk cache.
So consolidate the flushing code and implement it in C and inline asm
under the mm/ directory with the rest of the flush code. Add ISA v3.0B
cases for radix and hash, and use the radix flush in radix environment.
Provide a way for IS=2 (LPID flush) to specify the radix mode of the
partition. Have KVM pass in the radix mode of the guest.
Take out the flushes from early cputable/dt_cpu_ftrs detection hooks,
and move it later in the boot process after, the MMU registers are set
up and before relocation is first turned on.
The TLB flush is no longer called when restoring from deep idle states.
This was not be done as a separate step because booting secondaries
uses the same cpu_restore as idle restore, which needs the TLB flush.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The die() oops path contains a serializing lock to prevent oops
messages from being interleaved. In the case of a system reset
initiated oops (e.g., qemu nmi command), __die was being called
which lacks that synchronisation and oops reports could be
interleaved across CPUs.
A recent patch 4388c9b3a6 ("powerpc: Do not send system reset
request through the oops path") changed this to __die to avoid
the debugger() call, but there is no real harm to calling it twice
if the first time fell through. So go back to using die() here.
This was observed to fix the problem.
Fixes: 4388c9b3a6 ("powerpc: Do not send system reset request through the oops path")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Expose the state of the RFI flush (enabled/disabled) via debugfs, and
allow it to be enabled/disabled at runtime.
eg: $ cat /sys/kernel/debug/powerpc/rfi_flush
1
$ echo 0 > /sys/kernel/debug/powerpc/rfi_flush
$ cat /sys/kernel/debug/powerpc/rfi_flush
0
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
The recent commit 87590ce6e3 ("sysfs/cpu: Add vulnerability folder")
added a generic folder and set of files for reporting information on
CPU vulnerabilities. One of those was for meltdown:
/sys/devices/system/cpu/vulnerabilities/meltdown
This commit wires up that file for 64-bit Book3S powerpc.
For now we default to "Vulnerable" unless the RFI flush is enabled.
That may not actually be true on all hardware, further patches will
refine the reporting based on the CPU/platform etc. But for now we
default to being pessimists.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Trap numbers can have extra bits at the bottom that need to
be filtered out. There are a few cases where we don't do that.
It's possible that we got lucky but better safe than sorry.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The only difference between EXC_COMMON_HV and EXC_COMMON is that the
former adds "2" to the trap number which is supposed to represent the
fact that this is an "HV" interrupt which uses HSRR0/1.
However KVM is the only one who cares and it has its own separate macros.
In fact, we only have one user of EXC_COMMON_HV and it's for an
unknown interrupt case. All the other ones already using EXC_COMMON.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We used to not put the newline between the CPU part and the summary
part on UP kernels. This is a rather pointless ifdef so take it out.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When CONFIG_SWAP is set, the TLB miss handlers have to also take
into account _PAGE_ACCESSED flag. At the moment it is done by
anding _PAGE_ACCESSED into _PAGE_PRESENT using 3 instructions.
This patch uses APG for handling _PAGE_ACCESSED, allowing to
just copy _PAGE_ACCESSED bit into APG field, hence reducing the
action to a single instruction.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As Linux kernel separates KERNEL and USER address spaces, there is
therefore no need to flag USER access at page level.
Today, the 8xx TLB handlers already handle user access in the L1 entry
through Access Protection Groups, it is then natural to move the user
access handling at PMD level once _PAGE_NA allows to handle PAGE_NONE
protection without _PAGE_USER
In the mean time, as we free up one bit in the PTE, we can use it to
include SPS (page size flag) in the PTE and avoid handling it at every
TLB miss hence removing special handling based on compiled page size.
For _PAGE_EXEC, we rework it to use PP PTE bits, avoiding the copy
of _PAGE_EXEC bit into the L1 entry. Unfortunatly we are not
able to put it at the correct location as it conflicts with
NA/RO/RW bits for data entries.
Upper bits of APG in L1 entry overlap with PMD base address. In
order to avoid having to filter that out, we set up all groups so that
upper bits can have any value.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit ac29c64089 ("powerpc/mm: Replace _PAGE_USER with
_PAGE_PRIVILEGED") introduced _PAGE_PRIVILEGED for BOOK3S/64
This patch generalises _PAGE_PRIVILEGED for all CPUs, allowing
to have either _PAGE_PRIVILEGED or _PAGE_USER or both.
PPC_8xx has a _PAGE_SHARED flag which is set for and only for
all non user pages. Lets rename it _PAGE_PRIVILEGED to remove
confusion as it has nothing to do with Linux shared pages.
On BookE, there's a _PAGE_BAP_SR which has to be set for kernel
pages: defining _PAGE_PRIVILEGED as _PAGE_BAP_SR will make
this generic
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
_PAGE_WRITETHRU is only used in:
* AMIGA_Z2RAM block driver which is never activated on powerPC
* Video/FB driver which is for PPC_PMAC
Therefore, no need to spend time in 8xx TLB miss handlers for
handling it.
And by removing it, we free up bit 20 which then avoids having
to clear it on each TLB miss.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In TLB miss handlers, updating the perf counter is only useful
when performing a perf analysis. As it has a noticeable overhead,
let's only do it when needed.
In order to do so, the exit of the miss handlers will be patched
when starting/stopping 'perf': the first register restore
instruction of each exit point will be replaced by a jump to
the counting code.
Once this is done, CONFIG_PPC_8xx_PERF_EVENT becomes useless as
this feature doesn't add any overhead.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
EXCEPTION_PROLOG_0 and EXCEPTION_EPILOG_0 were added some
time ago in order to regroup the two mtspr/mfspr to SCRATCH0 and
SCRATCH1 and the mfcr/mtcr in order to ease entry and exit of
function not using the full EXCEPTION_PROLOG.
Since then, the mfcr/mtcr has been taken out, hence just leaving
the two mtspr/mfspr in the macro.
In order to improve readability of the exception functions, we
remove those two macros and copy back the two mtspr/mfspr instead.
As r10 and r11 are used for SCRATCH0 and SCRATCH1, lets also use
r12 for SCRATCH2. It will also improve the readability/maintenance.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CPU6 ERRATA affects only MPC860 revisions prior to C.0. Manufacturing
of those revisiosn was stopped in 1999-2000.
Therefore, it has been almost 20 years since this ERRATA has been
fixed in the silicon.
This patch removes the workaround for that ERRATA.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Certain HMI's such as malfunction error propagate through
all threads/core on the system. If a thread was offline
prior to us crashing the system and jumping to the kdump
kernel, bad things happen when it wakes up due to an HMI
in the kdump kernel.
There are several possible ways to solve this problem
1. Put the offline cores in a state such that they are
not woken up for machine check and HMI errors. This
does not work, since we might need to wake up offline
threads to handle TB errors
2. Ignore HMI errors, setup HMEER to mask HMI errors,
but this still leads the window open for any MCEs
and masking them for the duration of the dump might
be a concern
3. Wake up offline CPUs, as in send them to
crash_ipi_callback (not wake them up as in mark them
online as seen by the hotplug). kexec does a
wake_online_cpus() call, this patch does something
similar, but instead sends an IPI and forces them to
crash_ipi_callback()
This patch takes approach #3.
Care is taken to enable this only for powenv platforms
via crash_wake_offline (a global value set at setup
time). The crash code sends out IPI's to all CPU's
which then move to crash_ipi_callback and kexec_smp_wait().
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Our check was extra cautious, we've audited crash_send_ipi
and it sends an IPI only to online CPU's. Removal of this
check should have not functional impact on crash kdump.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Instead of manually coding the loop with of_find_node_by_type(), let's
switch to the standard macro for iterating over nodes with given type.
Also fixed a couple of refcount leaks in the aforementioned loops.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add required bits to the architecture vector to enable support
of the ibm,dynamic-memory-v2 device tree property.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We currently have code to parse the dynamic reconfiguration LMB
information from the ibm,dynamic-meory device tree property in
multiple locations; numa.c, prom.c, and pseries/hotplug-memory.c.
In anticipation of adding support for a version 2 of the
ibm,dynamic-memory property this patch aims to separate the device
tree information from the device tree format.
Doing this requires a two step process to avoid a possibly very large
bootmem allocation early in boot. During initial boot, new routines
are provided to walk the device tree property and make a call-back
for each LMB.
The second step (introduced in later patches) will allocate an
array of LMB information that can be used directly without needing
to know the DT format.
This approach provides the benefit of consolidating the device tree
property parsing to a single location and (eventually) providing
a common data structure for retrieving LMB information.
This patch introduces a routine to walk the ibm,dynamic-memory
property in the flattened device tree and updates the prom.c code
to use this to initialize memory.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Among the existing architecture specific versions of
copy_siginfo_to_user32 there are several different implementation
problems. Some architectures fail to handle all of the cases in in
the siginfo union. Some architectures perform a blind copy of the
siginfo union when the si_code is negative. A blind copy suggests the
data is expected to be in 32bit siginfo format, which means that
receiving such a signal via signalfd won't work, or that the data is
in 64bit siginfo and the code is copying nonsense to userspace.
Create a single instance of copy_siginfo_to_user32 that all of the
architectures can share, and teach it to handle all of the cases in
the siginfo union correctly, with the assumption that siginfo is
stored internally to the kernel is 64bit siginfo format.
A special case is made for x86 x32 format. This is needed as presence
of both x32 and ia32 on x86_64 results in two different 32bit signal
formats. By allowing this small special case there winds up being
exactly one code base that needs to be maintained between all of the
architectures. Vastly increasing the testing base and the chances of
finding bugs.
As the x86 copy of copy_siginfo_to_user32 the call of the x86
signal_compat_build_tests were moved into sigaction_compat_abi, so
that they will keep running.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The function copy_siginfo_from_user32 is used for two things, in ptrace
since the dawn of siginfo for arbirarily modifying a signal that
user space sees, and in sigqueueinfo to send a signal with arbirary
siginfo data.
Create a single copy of copy_siginfo_from_user32 that all architectures
share, and teach it to handle all of the cases in the siginfo union.
In the generic version of copy_siginfo_from_user32 ensure that all
of the fields in siginfo are initialized so that the siginfo structure
can be safely copied to userspace if necessary.
When copying the embedded sigval union copy the si_int member. That
ensures the 32bit values passes through the kernel unchanged.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
We'll need that name for a generic implementation soon.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Lift the code from x86 so that we behave consistently. In the future we
should probably warn if any of these is set.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Setting si_code to 0 results in a userspace seeing an si_code of 0.
This is the same si_code as SI_USER. Posix and common sense requires
that SI_USER not be a signal specific si_code. As such this use of 0
for the si_code is a pretty horribly broken ABI.
Further use of si_code == 0 guaranteed that copy_siginfo_to_user saw a
value of __SI_KILL and now sees a value of SIL_KILL with the result
that uid and pid fields are copied and which might copying the si_addr
field by accident but certainly not by design. Making this a very
flakey implementation.
Utilizing FPE_FIXME and TRAP_FIXME, siginfo_layout() will now return
SIL_FAULT and the appropriate fields will be reliably copied.
Possible ABI fixes includee:
- Send the signal without siginfo
- Don't generate a signal
- Possibly assign and use an appropriate si_code
- Don't handle cases which can't happen
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Ref: 9bad068c24d7 ("[PATCH] ppc32: support for e500 and 85xx")
Ref: 0ed70f6105ef ("PPC32: Provide proper siginfo information on various exceptions.")
History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Getting ready to remove pci_get_bus_and_slot() function in favor of
pci_get_domain_bus_and_slot().
Use pci_get_domain_bus_and_slot() with a domain number of 0 as the code
is not ready to consume multiple domains and existing code used domain
number 0.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
We want to use the dma_direct_ namespace for a generic implementation,
so rename powerpc to the second best choice: dma_nommu_.
Signed-off-by: Christoph Hellwig <hch@lst.de>
This causes warnings from cpufreq mutex code. This is also rather
unnecessary and ineffective. If we really want to prevent concurrent
unplug, we could take the unplug read lock but I don't see this being
critical.
Fixes: cd77b5ce20 ("powerpc/powernv/cpufreq: Fix the frequency read by /proc/cpuinfo")
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Because there may be some performance overhead of the RFI flush, add
kernel command line options to disable it.
We add a sensibly named 'no_rfi_flush' option, but we also hijack the
x86 option 'nopti'. The RFI flush is not the same as KPTI, but if we
see 'nopti' we can guess that the user is trying to avoid any overhead
of Meltdown mitigations, and it means we don't have to educate every
one about a different command line option.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On some CPUs we can prevent the Meltdown vulnerability by flushing the
L1-D cache on exit from kernel to user mode, and from hypervisor to
guest.
This is known to be the case on at least Power7, Power8 and Power9. At
this time we do not know the status of the vulnerability on other CPUs
such as the 970 (Apple G5), pasemi CPUs (AmigaOne X1000) or Freescale
CPUs. As more information comes to light we can enable this, or other
mechanisms on those CPUs.
The vulnerability occurs when the load of an architecturally
inaccessible memory region (eg. userspace load of kernel memory) is
speculatively executed to the point where its result can influence the
address of a subsequent speculatively executed load.
In order for that to happen, the first load must hit in the L1,
because before the load is sent to the L2 the permission check is
performed. Therefore if no kernel addresses hit in the L1 the
vulnerability can not occur. We can ensure that is the case by
flushing the L1 whenever we return to userspace. Similarly for
hypervisor vs guest.
In order to flush the L1-D cache on exit, we add a section of nops at
each (h)rfi location that returns to a lower privileged context, and
patch that with some sequence. Newer firmwares are able to advertise
to us that there is a special nop instruction that flushes the L1-D.
If we do not see that advertised, we fall back to doing a displacement
flush in software.
For guest kernels we support migration between some CPU versions, and
different CPUs may use different flush instructions. So that we are
prepared to migrate to a machine with a different flush instruction
activated, we may have to patch more than one flush instruction at
boot if the hypervisor tells us to.
In the end this patch is mostly the work of Nicholas Piggin and
Michael Ellerman. However a cast of thousands contributed to analysis
of the issue, earlier versions of the patch, back ports testing etc.
Many thanks to all of them.
Tested-by: Jon Masters <jcm@redhat.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the SLB miss handler we may be returning to user or kernel. We need
to add a check early on and save the result in the cr4 register, and
then we bifurcate the return path based on that.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Similar to the syscall return path, in fast_exception_return we may be
returning to user or kernel context. We already have a test for that,
because we conditionally restore r13. So use that existing test and
branch, and bifurcate the return based on that.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the syscall exit path we may be returning to user or kernel
context. We already have a test for that, because we conditionally
restore r13. So use that existing test and branch, and bifurcate the
return based on that.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This commit does simple conversions of rfi/rfid to the new macros that
include the expected destination context. By simple we mean cases
where there is a single well known destination context, and it's
simply a matter of substituting the instruction for the appropriate
macro.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are moving towards separate kernel and module function descriptor
dereference callbacks. This patch enables it for powerpc64.
For pointers that belong to the kernel
- Added __start_opd and __end_opd pointers, to track the kernel
.opd section address range;
- Added dereference_kernel_function_descriptor(). Now we
will dereference only function pointers that are within
[__start_opd, __end_opd);
For pointers that belong to a module
- Added dereference_module_function_descriptor() to handle module
function descriptor dereference. Now we will dereference only
pointers that are within [module->opd.start, module->opd.end).
Link: http://lkml.kernel.org/r/20171109234830.5067-4-sergey.senozhatsky@gmail.com
To: Tony Luck <tony.luck@intel.com>
To: Fenghua Yu <fenghua.yu@intel.com>
To: Helge Deller <deller@gmx.de>
To: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To: Paul Mackerras <paulus@samba.org>
To: Michael Ellerman <mpe@ellerman.id.au>
To: James Bottomley <jejb@parisc-linux.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-ia64@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Santosh Sivaraj <santosh@fossix.org> #powerpc
Signed-off-by: Petr Mladek <pmladek@suse.com>
The current scanning code is really hard to understand because it calls the
same function in a loop where pass value is changed without any comments
explaining it:
for (pass = 0; pass < 2; pass++)
for_each_pci_bridge(dev, bus)
max = pci_scan_bridge(bus, dev, max, pass);
Unfamiliar reader cannot tell easily what is the purpose of this loop
without looking at internals of pci_scan_bridge().
In order to make this bit easier to understand, open-code the loop in
pci_scan_child_bus() and pci_hp_add_bridge() with added comments.
No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use for_each_pci_bridge() helper to make the code slightly cleaner. No
functional change intended.
Requires: 24a0c654d7 ("PCI: Add for_each_pci_bridge() helper")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
When we oops or otherwise call show_regs() we print the address of the
regs structure. Being able to see the address is fairly useful,
firstly to verify that the regs pointer is not completely bogus, and
secondly it allows you to dump the regs and surrounding memory with a
debugger if you have one.
In the normal case the regs will be located somewhere on the stack, so
printing their location discloses no further information than printing
the stack pointer does already.
So switch to %px and print the actual address, not the hashed value.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
SR-IOV can now be enabled for the powernv platform and pseries
platform. Therefore move the appropriate calls to machine dependent
code instead of relying on definition at compile time.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@us.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc64 gcc can generate code that offsets an address, to access
part of an object in memory. If the address is a -mcmodel=medium toc
pointer relative address then code like the following is possible.
addis r9,r2,var@toc@ha
ld r3,var@toc@l(r9)
ld r4,(var+8)@toc@l(r9)
This works fine so long as var is naturally aligned, *and* r2 is
sufficiently aligned. If not, there is a possibility that the offset
added to access var+8 wraps over a n*64k+32k boundary. Modules don't
have any guarantee that r2 is sufficiently aligned. Moreover, code
generated by older compilers generates a .toc section with 2**0
alignment, which can result in relocation failures at module load time
even without the wrap problem.
Thus, this patch links modules with an aligned .toc section (Makefile
and module.lds changes), and forces alignment for out of tree modules
or those without a .toc section (module_64.c changes).
Signed-off-by: Alan Modra <amodra@gmail.com>
[desnesn: updated patch to apply to powerpc-next kernel v4.15 ]
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
[mpe: Fix out-of-tree build, swap -256 for ~0xff, reflow comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When an interrupt is returning to a soft-disabled context (which can
happen for non-maskable interrupts or synchronous interrupts), it goes
through the motions of soft-disabling again, including calling
TRACE_DISABLE_INTS (i.e., trace_hardirqs_off()).
This is not necessary, because we must already be soft-disabled in the
interrupt context, it also may be causing crashes in the irq tracing
code to re-enter as an nmi. Replace it with a warning to ensure that
soft-interrupts are still disabled.
Fixes: 7c0482e3d0 ("powerpc/irq: Fix another case of lazy IRQ state getting out of sync")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Match powerpc/64 and include .data.rel* input sections in the .data output
section explicitly.
This solves the warning:
powerpc-linux-gnu-ld: warning: orphan section `.data.rel.ro' from `arch/powerpc/kernel/head_44x.o' being placed in section `.data.rel.ro'.
Link: https://lists.01.org/pipermail/kbuild-all/2017-November/040010.html
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Print the function address associated with the restore_r2() error to
make it easier to debug the problem.
Also clarify the wording a bit.
Before:
module_64: patch_foo: Expect noop after relocate, got 3c820000
After:
module_64: patch_foo: Expected nop after call, got 7c630034 at netdev_has_upper_dev+0x54/0xb0 [patch_foo]
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
[mpe: Change noop to nop, as that's the name of the instruction]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When attempting to load a livepatch module, I got the following error:
module_64: patch_module: Expect noop after relocate, got 3c820000
The error was triggered by the following code in
unregister_netdevice_queue():
14c: 00 00 00 48 b 14c <unregister_netdevice_queue+0x14c>
14c: R_PPC64_REL24 net_set_todo
150: 00 00 82 3c addis r4,r2,0
GCC didn't insert a nop after the branch to net_set_todo() because it's
a sibling call, so it never returns. The nop isn't needed after the
branch in that case.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-and-tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Livepatch re-uses module loader function apply_relocate_add() to write
relocations, instead of managing them by arch-dependent
klp_write_module_reloc() function.
apply_relocate_add() doesn't understand livepatch symbols (marked with
SHN_LIVEPATCH symbol section index) and assumes them to be local
symbols by default for R_PPC64_REL24 relocation type. It fails with an
error, when trying to calculate offset with local_entry_offset():
module_64: kpatch_meminfo: REL24 -1152921504897399800 out of range!
Whereas livepatch symbols are essentially SHN_UNDEF, should be called
via stub used for global calls. This issue can be fixed by teaching
apply_relocate_add() to handle both SHN_UNDEF/SHN_LIVEPATCH symbols
via the same stub. This patch extends SHN_UNDEF code to handle
livepatch symbols too.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This statement causes some not very useful messages to always
be printed on the serial port at boot, even on quiet boots.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
kexec can leave MMU registers set when booting into a new kernel,
the PIDR (Process Identification Register) in particular. The boot
sequence does not zero PIDR, so it only gets set when CPUs first
switch to a userspace processes (until then it's running a kernel
thread with effective PID = 0).
This leaves a window where a process table entry and page tables are
set up due to user processes running on other CPUs, that happen to
match with a stale PID. The CPU with that PID may cause speculative
accesses that address quadrant 0 (aka userspace addresses), which will
result in cached translations and PWC (Page Walk Cache) for that
process, on a CPU which is not in the mm_cpumask and so they will not
be invalidated properly.
The most common result is the kernel hanging in infinite page fault
loops soon after kexec (usually in schedule_tail, which is usually the
first non-speculative quadrant 0 access to a new PID) due to a stale
PWC. However being a stale translation error, it could result in
anything up to security and data corruption problems.
Fix this by zeroing out PIDR at boot and kexec.
Fixes: 7e381c0ff6 ("powerpc/mm/radix: Add mmu context handling callback for radix")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit a3b2cb30f2.
That commit tried to fix problems with panic on powerpc in certain
circumstances, where some output from the generic panic code was being
dropped.
Unfortunately, it breaks things worse in other circumstances. In
particular when running a PAPR guest, it will now attempt to reboot
instead of informing the hypervisor (KVM or PowerVM) that the guest
has crashed. The crash notification is important to some
virtualization management layers.
Revert it for now until we can come up with a better solution.
Fixes: a3b2cb30f2 ("powerpc: Do not call ppc_md.panic in fadump panic notifier")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[mpe: Tweak change log a bit]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Live patching consistency model is of LEAVE_PATCHED_SET and
SWITCH_THREAD. This means that all tasks in the system have to be marked
one by one as safe to call a new patched function. Safe means when a
task is not (sleeping) in a set of patched functions. That is, no
patched function is on the task's stack. Another clearly safe place is
the boundary between kernel and userspace. The patching waits for all
tasks to get outside of the patched set or to cross the boundary. The
transition is completed afterwards.
The problem is that a task can block the transition for quite a long
time, if not forever. It could sleep in a set of patched functions, for
example. Luckily we can force the task to leave the set by sending it a
fake signal, that is a signal with no data in signal pending structures
(no handler, no sign of proper signal delivered). Suspend/freezer use
this to freeze the tasks as well. The task gets TIF_SIGPENDING set and
is woken up (if it has been sleeping in the kernel before) or kicked by
rescheduling IPI (if it was running on other CPU). This causes the task
to go to kernel/userspace boundary where the signal would be handled and
the task would be marked as safe in terms of live patching.
There are tasks which are not affected by this technique though. The
fake signal is not sent to kthreads. They should be handled differently.
They can be woken up so they leave the patched set and their
TIF_PATCH_PENDING can be cleared thanks to stack checking.
For the sake of completeness, if the task is in TASK_RUNNING state but
not currently running on some CPU it doesn't get the IPI, but it would
eventually handle the signal anyway. Second, if the task runs in the
kernel (in TASK_RUNNING state) it gets the IPI, but the signal is not
handled on return from the interrupt. It would be handled on return to
the userspace in the future when the fake signal is sent again. Stack
checking deals with these cases in a better way.
If the task was sleeping in a syscall it would be woken by our fake
signal, it would check if TIF_SIGPENDING is set (by calling
signal_pending() predicate) and return ERESTART* or EINTR. Syscalls with
ERESTART* return values are restarted in case of the fake signal (see
do_signal()). EINTR is propagated back to the userspace program. This
could disturb the program, but...
* each process dealing with signals should react accordingly to EINTR
return values.
* syscalls returning EINTR happen to be quite common situation in the
system even if no fake signal is sent.
* freezer sends the fake signal and does not deal with EINTR anyhow.
Thus EINTR values are returned when the system is resumed.
The very safe marking is done in architectures' "entry" on syscall and
interrupt/exception exit paths, and in a stack checking functions of
livepatch. TIF_PATCH_PENDING is cleared and the next
recalc_sigpending() drops TIF_SIGPENDING. In connection with this, also
call klp_update_patch_state() before do_signal(), so that
recalc_sigpending() in dequeue_signal() can clear TIF_PATCH_PENDING
immediately and thus prevent a double call of do_signal().
Note that the fake signal is not sent to stopped/traced tasks. Such task
prevents the patching to finish till it continues again (is not traced
anymore).
Last, sending the fake signal is not automatic. It is done only when
admin requests it by writing 1 to signal sysfs attribute in livepatch
sysfs directory.
Signed-off-by: Miroslav Benes <mbenes@suse.cz>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: x86@kernel.org
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Current vDSO64 implementation does not have support for coarse clocks
(CLOCK_MONOTONIC_COARSE, CLOCK_REALTIME_COARSE), for which it falls back
to system call, increasing the response time, vDSO implementation reduces
the cycle time. Below is a benchmark of the difference in execution times.
(Non-coarse clocks are also included just for completion)
clock-gettime-realtime: syscall: 172 nsec/call
clock-gettime-realtime: libc: 28 nsec/call
clock-gettime-realtime: vdso: 22 nsec/call
clock-gettime-monotonic: syscall: 171 nsec/call
clock-gettime-monotonic: libc: 30 nsec/call
clock-gettime-monotonic: vdso: 25 nsec/call
clock-gettime-realtime-coarse: syscall: 153 nsec/call
clock-gettime-realtime-coarse: libc: 16 nsec/call
clock-gettime-realtime-coarse: vdso: 10 nsec/call
clock-gettime-monotonic-coarse: syscall: 167 nsec/call
clock-gettime-monotonic-coarse: libc: 17 nsec/call
clock-gettime-monotonic-coarse: vdso: 11 nsec/call
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At some point, pr_warning will be removed so all logging messages use
a consistent <prefix>_warn style.
Update arch/powerpc/
Miscellanea:
o Coalesce formats
o Realign arguments
o Use %s, __func__ instead of embedded function names
o Remove unnecessary line continuations
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Geoff Levand <geoff@infradead.org>
[mpe: Rebase due to some %pOF changes.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Two fixes for nasty kexec/kdump crashes in certain configurations.
A couple of minor fixes for the new TIDR code.
A fix for an oops in a CXL error handling path.
Thanks to:
Andrew Donnellan, Christophe Lombard, David Gibson, Mahesh Salgaonkar, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----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=/LD/
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two fixes for nasty kexec/kdump crashes in certain configurations.
A couple of minor fixes for the new TIDR code.
A fix for an oops in a CXL error handling path.
Thanks to: Andrew Donnellan, Christophe Lombard, David Gibson, Mahesh
Salgaonkar, Vaibhav Jain"
* tag 'powerpc-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Do not assign thread.tidr if already assigned
powerpc: Avoid signed to unsigned conversion in set_thread_tidr()
powerpc/kexec: Fix kexec/kdump in P9 guest kernels
powerpc/powernv: Fix kexec crashes caused by tlbie tracing
cxl: Check if vphb exists before iterating over AFU devices
If set_thread_tidr() is called twice for same task_struct then it will
allocate a new tidr value to it leaving the previous value still
dangling in the vas_thread_ida table.
To fix this the patch changes set_thread_tidr() to check if a tidr
value is already assigned to the task_struct and if yes then returns
zero.
Fixes: ec233ede4c86("powerpc: Add support for setting SPRN_TIDR")
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
[mpe: Modify to return 0 in the success case, not the TID value]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is an unsafe signed to unsigned conversion in set_thread_tidr()
that may cause an error value to be assigned to SPRN_TIDR register and
used as thread-id.
The issue happens as assign_thread_tidr() returns an int and
thread.tidr is an unsigned-long. So a negative error code returned
from assign_thread_tidr() will fail the error check and gets assigned
as tidr as a large positive value.
To fix this the patch assigns the return value of assign_thread_tidr()
to a temporary int and assigns it to thread.tidr iff its '> 0'.
The patch shouldn't impact the calling convention of set_thread_tidr()
i.e all -ve return-values are error codes and a return value of '0'
indicates success.
Fixes: ec233ede4c86("powerpc: Add support for setting SPRN_TIDR")
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Christophe Lombard clombard@linux.vnet.ibm.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
A small batch of fixes, about 50% tagged for stable and the rest for recently
merged code.
There's one more fix for the >128T handling on hash. Once a process had
requested a single mmap above 128T we would then always search above 128T. The
correct behaviour is to consider the hint address in isolation for each mmap
request.
Then a couple of fixes for the IMC PMU, a missing EXPORT_SYMBOL in VAS, a fix
for STRICT_KERNEL_RWX on 32-bit, and a fix to correctly identify P9 DD2.1 but in
code that is currently not used by default.
Thanks to:
Aneesh Kumar K.V, Christophe Leroy, Madhavan Srinivasan, Sukadev Bhattiprolu.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gv70
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A small batch of fixes, about 50% tagged for stable and the rest for
recently merged code.
There's one more fix for the >128T handling on hash. Once a process
had requested a single mmap above 128T we would then always search
above 128T. The correct behaviour is to consider the hint address in
isolation for each mmap request.
Then a couple of fixes for the IMC PMU, a missing EXPORT_SYMBOL in
VAS, a fix for STRICT_KERNEL_RWX on 32-bit, and a fix to correctly
identify P9 DD2.1 but in code that is currently not used by default.
Thanks to: Aneesh Kumar K.V, Christophe Leroy, Madhavan Srinivasan,
Sukadev Bhattiprolu"
* tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix Power9 DD2.1 logic in DT CPU features
powerpc/perf: Fix IMC_MAX_PMU macro
powerpc/perf: Fix pmu_count to count only nest imc pmus
powerpc: Fix boot on BOOK3S_32 with CONFIG_STRICT_KERNEL_RWX
powerpc/perf/imc: Use cpu_to_node() not topology_physical_package_id()
powerpc/vas: Export chip_to_vas_id()
powerpc/64s/slice: Use addr limit when computing slice mask
The code that cleans up the IAMR/AMOR before kexec'ing failed to
remember that when we're running as a guest AMOR is not writable, it's
hypervisor privileged.
They symptom is that the kexec stops before entering purgatory and
nothing else is seen on the console. If you examine the state of the
system all threads will be in the 0x700 program check handler.
Fix it by making the write to AMOR dependent on HV mode.
Fixes: 1e2a516e89 ("powerpc/kexec: Fix radix to hash kexec due to IAMR/AMOR")
Cc: stable@vger.kernel.org # v4.10+
Reported-by: Yilin Zhang <yilzhang@redhat.com>
Debugged-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
I got the logic wrong in the DT CPU features code when I added the
Power9 DD2.1 feature. We should be setting the bit if we detect a
DD2.1, not clearing it if we detect a DD2.0.
This code isn't actually exercised at the moment so nothing is
actually broken.
Fixes: 3ffa9d9e2a ("powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull compat and uaccess updates from Al Viro:
- {get,put}_compat_sigset() series
- assorted compat ioctl stuff
- more set_fs() elimination
- a few more timespec64 conversions
- several removals of pointless access_ok() in places where it was
followed only by non-__ variants of primitives
* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (24 commits)
coredump: call do_unlinkat directly instead of sys_unlink
fs: expose do_unlinkat for built-in callers
ext4: take handling of EXT4_IOC_GROUP_ADD into a helper, get rid of set_fs()
ipmi: get rid of pointless access_ok()
pi433: sanitize ioctl
cxlflash: get rid of pointless access_ok()
mtdchar: get rid of pointless access_ok()
r128: switch compat ioctls to drm_ioctl_kernel()
selection: get rid of field-by-field copyin
VT_RESIZEX: get rid of field-by-field copyin
i2c compat ioctls: move to ->compat_ioctl()
sched_rr_get_interval(): move compat to native, get rid of set_fs()
mips: switch to {get,put}_compat_sigset()
sparc: switch to {get,put}_compat_sigset()
s390: switch to {get,put}_compat_sigset()
ppc: switch to {get,put}_compat_sigset()
parisc: switch to {get,put}_compat_sigset()
get_compat_sigset()
get rid of {get,put}_compat_itimerspec()
io_getevents: Use timespec64 to represent timeouts
...
Common:
- Python 3 support in kvm_stat
- Accounting of slabs to kmemcg
ARM:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
PPC:
- Support for running hashed page table (HPT) MMU mode on a host that
is using the radix MMU mode; single threaded mode on POWER 9 is
added as a pre-requisite
- Resolution of merge conflicts with the last second 4.14 HPT fixes
- Fixes and cleanups
s390:
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
x86:
- Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs, and
after-reset state
- Refined dependencies for VMX features
- Fixes for nested SMI injection
- A lot of cleanups
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJaDayXAAoJEED/6hsPKofo/3UH/3HvlcHt+ADTkCU1/iiKAs+i
0zngIOXIxgHDnV0ww6bV+Znww0BzTYgKCAXX76z603jdpDwG/pzQQcbLDF5ZoJnD
sQtF10gZinWaRsHlfbLqjrHGL2pGDHO1UKBKLJ0bAIyORPZBxs7i+VmrY/blnr9c
0wsybJ8RbvwAxjsDL5jeX/z4NehPupmKUc4Lf0eZdSHwVOf9sjn+MP6jJ0r2JcIb
D+zddPBiLStzN97t4gZpQsrlj3LKrDS+6hY+1TjSvlh+yHKFVFh58VhLm4DuDeb5
bYOAlWJ/gAWEzfvr5Ld+Nd7SqWWn/14logPkQ4gcU4BI/neAOzk4c6hJfCHl1nk=
=593n
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"First batch of KVM changes for 4.15
Common:
- Python 3 support in kvm_stat
- Accounting of slabs to kmemcg
ARM:
- Optimized arch timer handling for KVM/ARM
- Improvements to the VGIC ITS code and introduction of an ITS reset
ioctl
- Unification of the 32-bit fault injection logic
- More exact external abort matching logic
PPC:
- Support for running hashed page table (HPT) MMU mode on a host that
is using the radix MMU mode; single threaded mode on POWER 9 is
added as a pre-requisite
- Resolution of merge conflicts with the last second 4.14 HPT fixes
- Fixes and cleanups
s390:
- Some initial preparation patches for exitless interrupts and crypto
- New capability for AIS migration
- Fixes
x86:
- Improved emulation of LAPIC timer mode changes, MCi_STATUS MSRs,
and after-reset state
- Refined dependencies for VMX features
- Fixes for nested SMI injection
- A lot of cleanups"
* tag 'kvm-4.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (89 commits)
KVM: s390: provide a capability for AIS state migration
KVM: s390: clear_io_irq() requests are not expected for adapter interrupts
KVM: s390: abstract conversion between isc and enum irq_types
KVM: s390: vsie: use common code functions for pinning
KVM: s390: SIE considerations for AP Queue virtualization
KVM: s390: document memory ordering for kvm_s390_vcpu_wakeup
KVM: PPC: Book3S HV: Cosmetic post-merge cleanups
KVM: arm/arm64: fix the incompatible matching for external abort
KVM: arm/arm64: Unify 32bit fault injection
KVM: arm/arm64: vgic-its: Implement KVM_DEV_ARM_ITS_CTRL_RESET
KVM: arm/arm64: Document KVM_DEV_ARM_ITS_CTRL_RESET
KVM: arm/arm64: vgic-its: Free caches when GITS_BASER Valid bit is cleared
KVM: arm/arm64: vgic-its: New helper functions to free the caches
KVM: arm/arm64: vgic-its: Remove kvm_its_unmap_device
arm/arm64: KVM: Load the timer state when enabling the timer
KVM: arm/arm64: Rework kvm_timer_should_fire
KVM: arm/arm64: Get rid of kvm_timer_flush_hwstate
KVM: arm/arm64: Avoid phys timer emulation in vcpu entry/exit
KVM: arm/arm64: Move phys_timer_emulate function
KVM: arm/arm64: Use kvm_arm_timer_set/get_reg for guest register traps
...
Non-highlights:
- Five fixes for the >128T address space handling, both to fix bugs in our
implementation and to bring the semantics exactly into line with x86.
Highlights:
- Support for a new OPAL call on bare metal machines which gives us a true NMI
(ie. is not masked by MSR[EE]=0) for debugging etc.
- Support for Power9 DD2 in the CXL driver.
- Improvements to machine check handling so that uncorrectable errors can be
reported into the generic memory_failure() machinery.
- Some fixes and improvements for VPHN, which is used under PowerVM to notify
the Linux partition of topology changes.
- Plumbing to enable TM (transactional memory) without suspend on some Power9
processors (PPC_FEATURE2_HTM_NO_SUSPEND).
- Support for emulating vector loads form cache-inhibited memory, on some
Power9 revisions.
- Disable the fast-endian switch "syscall" by default (behind a CONFIG), we
believe it has never had any users.
- A major rework of the API drivers use when initiating and waiting for long
running operations performed by OPAL firmware, and changes to the
powernv_flash driver to use the new API.
- Several fixes for the handling of FP/VMX/VSX while processes are using
transactional memory.
- Optimisations of TLB range flushes when using the radix MMU on Power9.
- Improvements to the VAS facility used to access coprocessors on Power9, and
related improvements to the way the NX crypto driver handles requests.
- Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.
Thanks to:
Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew Donnellan, Aneesh
Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin Herrenschmidt, Breno Leitao,
Christophe Leroy, Christophe Lombard, Cyril Bur, Frederic Barrat, Gautham R.
Shenoy, Geert Uytterhoeven, Guilherme G. Piccoli, Gustavo Romero, Haren
Myneni, Joel Stanley, Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami
Hiramatsu, Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia Franco de
Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee, Shriya, Stephen
Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel Datwyler, Vaibhav Jain,
Vaidyanathan Srinivasan, William A. Kennington III.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Rq81
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A bit of a small release, I suspect in part due to me travelling for
KS. But my backlog of patches to review is smaller than usual, so I
think in part folks just didn't send as much this cycle.
Non-highlights:
- Five fixes for the >128T address space handling, both to fix bugs
in our implementation and to bring the semantics exactly into line
with x86.
Highlights:
- Support for a new OPAL call on bare metal machines which gives us a
true NMI (ie. is not masked by MSR[EE]=0) for debugging etc.
- Support for Power9 DD2 in the CXL driver.
- Improvements to machine check handling so that uncorrectable errors
can be reported into the generic memory_failure() machinery.
- Some fixes and improvements for VPHN, which is used under PowerVM
to notify the Linux partition of topology changes.
- Plumbing to enable TM (transactional memory) without suspend on
some Power9 processors (PPC_FEATURE2_HTM_NO_SUSPEND).
- Support for emulating vector loads form cache-inhibited memory, on
some Power9 revisions.
- Disable the fast-endian switch "syscall" by default (behind a
CONFIG), we believe it has never had any users.
- A major rework of the API drivers use when initiating and waiting
for long running operations performed by OPAL firmware, and changes
to the powernv_flash driver to use the new API.
- Several fixes for the handling of FP/VMX/VSX while processes are
using transactional memory.
- Optimisations of TLB range flushes when using the radix MMU on
Power9.
- Improvements to the VAS facility used to access coprocessors on
Power9, and related improvements to the way the NX crypto driver
handles requests.
- Implementation of PMEM_API and UACCESS_FLUSHCACHE for 64-bit.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Allen Pais, Andrew
Donnellan, Aneesh Kumar K.V, Arnd Bergmann, Balbir Singh, Benjamin
Herrenschmidt, Breno Leitao, Christophe Leroy, Christophe Lombard,
Cyril Bur, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven,
Guilherme G. Piccoli, Gustavo Romero, Haren Myneni, Joel Stanley,
Kamalesh Babulal, Kautuk Consul, Markus Elfring, Masami Hiramatsu,
Michael Bringmann, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pedro Miraglia
Franco de Carvalho, Philippe Bergheaud, Sandipan Das, Seth Forshee,
Shriya, Stephen Rothwell, Stewart Smith, Sukadev Bhattiprolu, Tyrel
Datwyler, Vaibhav Jain, Vaidyanathan Srinivasan, and William A.
Kennington III"
* tag 'powerpc-4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (151 commits)
powerpc/64s: Fix Power9 DD2.0 workarounds by adding DD2.1 feature
powerpc/64s: Fix masking of SRR1 bits on instruction fault
powerpc/64s: mm_context.addr_limit is only used on hash
powerpc/64s/radix: Fix 128TB-512TB virtual address boundary case allocation
powerpc/64s/hash: Allow MAP_FIXED allocations to cross 128TB boundary
powerpc/64s/hash: Fix fork() with 512TB process address space
powerpc/64s/hash: Fix 128TB-512TB virtual address boundary case allocation
powerpc/64s/hash: Fix 512T hint detection to use >= 128T
powerpc: Fix DABR match on hash based systems
powerpc/signal: Properly handle return value from uprobe_deny_signal()
powerpc/fadump: use kstrtoint to handle sysfs store
powerpc/lib: Implement UACCESS_FLUSHCACHE API
powerpc/lib: Implement PMEM API
powerpc/powernv/npu: Don't explicitly flush nmmu tlb
powerpc/powernv/npu: Use flush_all_mm() instead of flush_tlb_mm()
powerpc/powernv/idle: Round up latency and residency values
powerpc/kprobes: refactor kprobe_lookup_name for safer string operations
powerpc/kprobes: Blacklist emulate_update_regs() from kprobes
powerpc/kprobes: Do not disable interrupts for optprobes and kprobes_on_ftrace
powerpc/kprobes: Disable preemption before invoking probe handler for optprobes
...
-----BEGIN PGP SIGNATURE-----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=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
Recently we added a CPU feature for Power9 DD2.0, to capture the fact
that some workarounds are required only on Power9 DD1 and DD2.0 but
not DD2.1 or later.
Then in commit 9d2f510a66 ("powerpc/64s/idle: avoid POWER9 DD1 and
DD2.0 ERAT workaround on DD2.1") and commit e3646330cf
"powerpc/64s/idle: avoid POWER9 DD1 and DD2.0 PMU workaround on
DD2.1") we changed CPU_FTR_SECTIONs to check for DD1 or DD20, eg:
BEGIN_FTR_SECTION
PPC_INVALIDATE_ERAT
END_FTR_SECTION_IFSET(CPU_FTR_POWER9_DD1 | CPU_FTR_POWER9_DD20)
Unfortunately although this reads as "if set DD1 or DD2.0", the or is
a bitwise or and actually generates a mask of both bits. The code that
does the feature patching then checks that the value of the CPU
features masked with that mask are equal to the mask.
So the end result is we're checking for DD1 and DD20 being set, which
never happens. Yes the API is terrible.
Removing the ERAT workaround on DD2.0 results in random SEGVs, the
system tends to boot, but things randomly die including sometimes
dhclient, udev etc.
To fix the problem and hopefully avoid it in future, we remove the
DD2.0 CPU feature and instead add a DD2.1 (or later) feature. This
allows us to easily express that the workarounds are required if DD2.1
is not set.
At some point we will drop the DD1 workarounds entirely and some of
this can be cleaned up.
Fixes: 9d2f510a66 ("powerpc/64s/idle: avoid POWER9 DD1 and DD2.0 ERAT workaround on DD2.1")
Fixes: e3646330cf ("powerpc/64s/idle: avoid POWER9 DD1 and DD2.0 PMU workaround on DD2.1")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On 64-bit Book3s, when we take an instruction fault the reason for the
fault may be reported in SRR1. For data faults the reason is reported
in DSISR (Data Storage Instruction Status Register).
The reasons reported in each do not necessarily correspond, so we mask
the SRR1 bits before copying them to the DSISR, which is then used by
the page fault code.
Prior to commit b4c001dc44 ("powerpc/mm: Use symbolic constants for
filtering SRR1 bits on ISIs") we used a hard-coded mask of 0x58200000,
which corresponds to:
DSISR_NOHPTE 0x40000000 /* no translation found */
DSISR_NOEXEC_OR_G 0x10000000 /* exec of no-exec or guarded */
DSISR_PROTFAULT 0x08000000 /* protection fault */
DSISR_KEYFAULT 0x00200000 /* Storage Key fault */
That commit added a #define for the mask, DSISR_SRR1_MATCH_64S, but
incorrectly used a different similarly named DSISR_BAD_FAULT_64S.
This had the effect of changing the mask to 0xa43a0000, which omits
everything but DSISR_KEYFAULT.
Luckily this had no visible effect, because in practice we hardly use
the DSISR bits. The lack of DSISR_NOHPTE means a TLB flush
optimisation was missed in the native HPTE code, and DSISR_NOEXEC_OR_G
and DSISR_PROTFAULT are both only used to trigger rare warnings.
So we got lucky, but let's fix it. The new value only has bits between
17 and 30 set, so we can continue to use andis.
Fixes: b4c001dc44 ("powerpc/mm: Use symbolic constants for filtering SRR1 bits on ISIs")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
Pull x86 core updates from Ingo Molnar:
"Note that in this cycle most of the x86 topics interacted at a level
that caused them to be merged into tip:x86/asm - but this should be a
temporary phenomenon, hopefully we'll back to the usual patterns in
the next merge window.
The main changes in this cycle were:
Hardware enablement:
- Add support for the Intel UMIP (User Mode Instruction Prevention)
CPU feature. This is a security feature that disables certain
instructions such as SGDT, SLDT, SIDT, SMSW and STR. (Ricardo Neri)
[ Note that this is disabled by default for now, there are some
smaller enhancements in the pipeline that I'll follow up with in
the next 1-2 days, which allows this to be enabled by default.]
- Add support for the AMD SEV (Secure Encrypted Virtualization) CPU
feature, on top of SME (Secure Memory Encryption) support that was
added in v4.14. (Tom Lendacky, Brijesh Singh)
- Enable new SSE/AVX/AVX512 CPU features: AVX512_VBMI2, GFNI, VAES,
VPCLMULQDQ, AVX512_VNNI, AVX512_BITALG. (Gayatri Kammela)
Other changes:
- A big series of entry code simplifications and enhancements (Andy
Lutomirski)
- Make the ORC unwinder default on x86 and various objtool
enhancements. (Josh Poimboeuf)
- 5-level paging enhancements (Kirill A. Shutemov)
- Micro-optimize the entry code a bit (Borislav Petkov)
- Improve the handling of interdependent CPU features in the early
FPU init code (Andi Kleen)
- Build system enhancements (Changbin Du, Masahiro Yamada)
- ... plus misc enhancements, fixes and cleanups"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (118 commits)
x86/build: Make the boot image generation less verbose
selftests/x86: Add tests for the STR and SLDT instructions
selftests/x86: Add tests for User-Mode Instruction Prevention
x86/traps: Fix up general protection faults caused by UMIP
x86/umip: Enable User-Mode Instruction Prevention at runtime
x86/umip: Force a page fault when unable to copy emulated result to user
x86/umip: Add emulation code for UMIP instructions
x86/cpufeature: Add User-Mode Instruction Prevention definitions
x86/insn-eval: Add support to resolve 16-bit address encodings
x86/insn-eval: Handle 32-bit address encodings in virtual-8086 mode
x86/insn-eval: Add wrapper function for 32 and 64-bit addresses
x86/insn-eval: Add support to resolve 32-bit address encodings
x86/insn-eval: Compute linear address in several utility functions
resource: Fix resource_size.cocci warnings
X86/KVM: Clear encryption attribute when SEV is active
X86/KVM: Decrypt shared per-cpu variables when SEV is active
percpu: Introduce DEFINE_PER_CPU_DECRYPTED
x86: Add support for changing memory encryption attribute in early boot
x86/io: Unroll string I/O when SEV is active
x86/boot: Add early boot support when running with SEV active
...
Radix keeps no meaningful state in addr_limit, so remove it from radix
code and rename to slb_addr_limit to make it clear it applies to hash
only.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 398a719d34 ("powerpc/mm: Update bits used to skip hash_page")
mistakenly dropped the DSISR_DABRMATCH bit from the mask of bit tested
to skip trying to hash a page.
As a result, the DABR matches would no longer be detected.
This adds it back. We open code it in the 2 places where it matters
rather than fold it into DSISR_BAD_FAULT_32S/64S because this isn't
technically a bad fault and while we would never hit it with the
current code, I prefer if page_fault_is_bad() didn't trigger on these.
Fixes: 398a719d34 ("powerpc/mm: Update bits used to skip hash_page")
Cc: stable@vger.kernel.org # v4.14
Tested-by: Pedro Miraglia Franco de Carvalho <pedromfc@br.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When a uprobe is installed on an instruction that we currently do not
emulate, we copy the instruction into a xol buffer and single step
that instruction. If that instruction generates a fault, we abort the
single stepping before invoking the signal handler. Once the signal
handler is done, the uprobe trap is hit again since the instruction is
retried and the process repeats.
We use uprobe_deny_signal() to detect if the xol instruction triggered
a signal. If so, we clear TIF_SIGPENDING and set TIF_UPROBE so that the
signal is not handled until after the single stepping is aborted. In
this case, uprobe_deny_signal() returns true and get_signal() ends up
returning 0. However, in do_signal(), we are not looking at the return
value, but depending on ksig.sig for further action, all with an
uninitialized ksig that is not touched in this scenario. Fix the same
by initializing ksig.sig to 0.
Fixes: 129b69df9c ("powerpc: Use get_signal() signal_setup_done()")
Cc: stable@vger.kernel.org # v3.17+
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently sysfs store handlers in fadump use if buf[0] == 'char'.
This means input "100foo" is interpreted as '1' and "01" as '0'.
Change to kstrtoint so leading zeroes and the like is handled in
expected way.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Acked-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michal Suchanek <a class="moz-txt-link-rfc2396E" href="mailto:msuchanek@suse.de"><msuchanek@suse.de></a></pre>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use safer string manipulation functions when dealing with a
user-provided string in kprobe_lookup_name().
Reported-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Per Documentation/kprobes.txt, we don't necessarily need to disable
interrupts before invoking the kprobe handlers. Masami submitted
similar changes for x86 via commit a19b2e3d78 ("kprobes/x86: Remove
IRQ disabling from ftrace-based/optimized kprobes"). Do the same for
powerpc.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Per Documentation/kprobes.txt, probe handlers need to be invoked with
preemption disabled. Update optimized_callback() to do so. Also move
get_kprobe_ctlblk() invocation post preemption disable, since it
accesses pre-cpu data.
This was not an issue so far since optprobes wasn't selected if
CONFIG_PREEMPT was enabled. Commit a30b85df7d ("kprobes: Use
synchronize_rcu_tasks() for optprobe with CONFIG_PREEMPT=y") changes
this.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 78adf6c214 ("powerpc/64s: Implement system reset idle wakeup
reason"), added a call to ppc_save_regs() in the book3s code.
ppc_save_regs() is only built if XMON and/or KEXEC_CORE are enabled,
which is usually the case, however if they're not enabled then the
build breaks.
Fix it by making the Makefile check also build ppc_save_regs.o if
CONFIG_PPC_BOOK3S is enabled.
Fixes: 78adf6c214 ("powerpc/64s: Implement system reset idle wakeup reason")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[mpe: Write change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A CP_ABORT instruction is required in processes that have mapped a VAS
"paste address" with the intention of using COPY/PASTE instructions.
But since CP_ABORT is expensive, we want to restrict it to only
processes that use/intend to use COPY/PASTE.
Define an interface, set_thread_uses_vas(), that VAS can use to
indicate that the current process opened a send window. During context
switch, issue CP_ABORT only for processes that have the flag set.
Thanks for input from Nick Piggin, Michael Ellerman.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
[mpe: Fix to not use new_thread after _switch() returns]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We need the SPRN_TIDR to be set for use with fast thread-wakeup (core-
to-core wakeup) and also with CAPI.
Each thread in a process needs to have a unique id within the process.
But for now, we assign globally unique thread ids to all threads in
the system.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
[mpe: Simplify tidr clearing on fork() and ctx switch code]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Take the DSCR value set by firmware as the dscr_default value,
rather than zero.
POWER9 recommends DSCR default to a non-zero value.
Signed-off-by: From: Nicholas Piggin <npiggin@gmail.com>
[mpe: Make record_spr_defaults() __init]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPAL boot does not insert secondaries at 0x60 to wait at the secondary
hold spinloop. Instead they are started later, and inserted at
generic_secondary_smp_init(), which is after the secondary hold
spinloop.
Avoid waiting on this spinloop when booting with OPAL firmware. This
wait always times out that case.
This saves 100ms boot time on powernv, and 10s of seconds of real time
when booting on the simulator in SMP.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have some dependencies & conflicts between patches in fixes and
things to go in next, both in the radix TLB flush code and the IMC PMU
driver. So merge fixes into next.
In preperation for a new function that will need additional resource
information during the resource walk, update the resource walk callback to
pass the resource structure. Since the current callback start and end
arguments are pulled from the resource structure, the callback functions
can obtain them from the resource structure directly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Tested-by: Borislav Petkov <bp@suse.de>
Cc: kvm@vger.kernel.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lkml.kernel.org/r/20171020143059.3291-10-brijesh.singh@amd.com
DD2.1 does not have to save MMCR0 for all state-loss idle states,
only after deep idle states (like other PMU registers).
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
DD2.1 does not have to flush the ERAT after a state-loss idle.
Performance testing was done on a DD2.1 using only the stop0 idle state
(the shallowest state which supports state loss), using context_switch
selftest configured to ping-poing between two threads on the same core
and two different cores.
Performance improvement for same core is 7.0%, different cores is 14.8%.
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After handling a transactional FP, Altivec or VSX unavailable exception.
The return to userspace code will detect that the TIF_RESTORE_TM bit is
set and call restore_tm_state(). restore_tm_state() will call
restore_math() to ensure that the correct facilities are loaded.
This means that all the loadup code in {fp,altivec,vsx}_unavailable_tm()
is doing pointless work and can simply be removed.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lazy save and restore of FP/Altivec means that a userspace process can
be sent to userspace with FP or Altivec disabled and loaded only as
required (by way of an FP/Altivec unavailable exception). Transactional
Memory complicates this situation as a transaction could be started
without FP/Altivec being loaded up. This causes the hardware to
checkpoint incorrect registers. Handling FP/Altivec unavailable
exceptions while a thread is transactional requires a reclaim and
recheckpoint to ensure the CPU has correct state for both sets of
registers.
tm_reclaim() has optimisations to not always save the FP/Altivec
registers to the checkpointed save area. This was originally done
because the caller might have information that the checkpointed
registers aren't valid due to lazy save and restore. We've also been a
little vague as to how tm_reclaim() leaves the FP/Altivec state since it
doesn't necessarily always save it to the thread struct. This has lead
to an (incorrect) assumption that it leaves the checkpointed state on
the CPU.
tm_recheckpoint() has similar optimisations in reverse. It may not
always reload the checkpointed FP/Altivec registers from the thread
struct before the trecheckpoint. It is therefore quite unclear where it
expects to get the state from. This didn't help with the assumption
made about tm_reclaim().
These optimisations sit in what is by definition a slow path. If a
process has to go through a reclaim/recheckpoint then its transaction
will be doomed on returning to userspace. This mean that the process
will be unable to complete its transaction and be forced to its failure
handler. This is already an out if line case for userspace. Furthermore,
the cost of copying 64 times 128 bits from registers isn't very long[0]
(at all) on modern processors. As such it appears these optimisations
have only served to increase code complexity and are unlikely to have
had a measurable performance impact.
Our transactional memory handling has been riddled with bugs. A cause
of this has been difficulty in following the code flow, code complexity
has not been our friend here. It makes sense to remove these
optimisations in favour of a (hopefully) more stable implementation.
This patch does mean that some times the assembly will needlessly save
'junk' registers which will subsequently get overwritten with the
correct value by the C code which calls the assembly function. This
small inefficiency is far outweighed by the reduction in complexity for
general TM code, context switching paths, and transactional facility
unavailable exception handler.
0: I tried to measure it once for other work and found that it was
hiding in the noise of everything else I was working with. I find it
exceedingly likely this will be the case here.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lazy save and restore of FP/Altivec means that a userspace process can
be sent to userspace with FP or Altivec disabled and loaded only as
required (by way of an FP/Altivec unavailable exception). Transactional
Memory complicates this situation as a transaction could be started
without FP/Altivec being loaded up. This causes the hardware to
checkpoint incorrect registers. Handling FP/Altivec unavailable
exceptions while a thread is transactional requires a reclaim and
recheckpoint to ensure the CPU has correct state for both sets of
registers.
tm_reclaim() has optimisations to not always save the FP/Altivec
registers to the checkpointed save area. This was originally done
because the caller might have information that the checkpointed
registers aren't valid due to lazy save and restore. We've also been a
little vague as to how tm_reclaim() leaves the FP/Altivec state since it
doesn't necessarily always save it to the thread struct. This has lead
to an (incorrect) assumption that it leaves the checkpointed state on
the CPU.
tm_recheckpoint() has similar optimisations in reverse. It may not
always reload the checkpointed FP/Altivec registers from the thread
struct before the trecheckpoint. It is therefore quite unclear where it
expects to get the state from. This didn't help with the assumption
made about tm_reclaim().
This patch is a minimal fix for ease of backporting. A more correct fix
which removes the msr parameter to tm_reclaim() and tm_recheckpoint()
altogether has been upstreamed to apply on top of this patch.
Fixes: dc3106690b ("powerpc: tm: Always use fp_state and vr_state to
store live registers")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Lazy save and restore of FP/Altivec means that a userspace process can
be sent to userspace with FP or Altivec disabled and loaded only as
required (by way of an FP/Altivec unavailable exception). Transactional
Memory complicates this situation as a transaction could be started
without FP/Altivec being loaded up. This causes the hardware to
checkpoint incorrect registers. Handling FP/Altivec unavailable
exceptions while a thread is transactional requires a reclaim and
recheckpoint to ensure the CPU has correct state for both sets of
registers.
Lazy save and restore of FP/Altivec cannot be done if a process is
transactional. If a facility was enabled it must remain enabled whenever
a thread is transactional.
Commit dc16b553c9 ("powerpc: Always restore FPU/VEC/VSX if hardware
transactional memory in use") ensures that the facilities are always
enabled if a thread is transactional. A bug in the introduced code may
cause it to inadvertently enable a facility that was (and should remain)
disabled. The problem with this extraneous enablement is that the
registers for the erroneously enabled facility have not been correctly
recheckpointed - the recheckpointing code assumed the facility would
remain disabled.
Further compounding the issue, the transactional {fp,altivec,vsx}
unavailable code has been incorrectly using the MSR to enable
facilities. The presence of the {FP,VEC,VSX} bit in the regs->msr simply
means if the registers are live on the CPU, not if the kernel should
load them before returning to userspace. This has worked due to the bug
mentioned above.
This causes transactional threads which return to their failure handler
to observe incorrect checkpointed registers. Perhaps an example will
help illustrate the problem:
A userspace process is running and uses both FP and Altivec registers.
This process then continues to run for some time without touching
either sets of registers. The kernel subsequently disables the
facilities as part of lazy save and restore. The userspace process then
performs a tbegin and the CPU checkpoints 'junk' FP and Altivec
registers. The process then performs a floating point instruction
triggering a fp unavailable exception in the kernel.
The kernel then loads the FP registers - and only the FP registers.
Since the thread is transactional it must perform a reclaim and
recheckpoint to ensure both the checkpointed registers and the
transactional registers are correct. It then (correctly) enables
MSR[FP] for the process. Later (on exception exist) the kernel also
(inadvertently) enables MSR[VEC]. The process is then returned to
userspace.
Since the act of loading the FP registers doomed the transaction we know
CPU will fail the transaction, restore its checkpointed registers, and
return the process to its failure handler. The problem is that we're
now running with Altivec enabled and the 'junk' checkpointed registers
are restored. The kernel had only recheckpointed FP.
This patch solves this by only activating FP/Altivec if userspace was
using them when it entered the kernel and not simply if the process is
transactional.
Fixes: dc16b553c9 ("powerpc: Always restore FPU/VEC/VSX if hardware
transactional memory in use")
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This interface is inefficient and deprecated because of the y2038
overflow.
ktime_get_seconds() is an appropriate replacement here, since it
has sufficient granularity but is more efficient and uses monotonic
time.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently when we take a TM Bad Thing program check exception, we
search the bug table to see if the program check was generated by a
WARN/WARN_ON etc.
That makes no sense, the WARN macros use trap instructions, which
should never generate a TM Bad Thing exception. If they ever did that
would be a bug and we should oops.
We do have some hand-coded bugs in tm.S, using EMIT_BUG_ENTRY, but
those are all BUGs not WARNs, and they all use trap instructions
anyway. Almost certainly this check was incorrectly copied from the
REASON_TRAP handling in the same function.
Remove it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-By: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_PPC_STD_MMU_64 indicates support for the "standard" powerpc MMU
on 64-bit CPUs. The "standard" MMU refers to the hash page table MMU
found in "server" processors, from IBM mainly.
Currently CONFIG_PPC_STD_MMU_64 is == CONFIG_PPC_BOOK3S_64. While it's
annoying to have two symbols that always have the same value, it's not
quite annoying enough to bother removing one.
However with the arrival of Power9, we now have the situation where
CONFIG_PPC_STD_MMU_64 is enabled, but the kernel is running using the
Radix MMU - *not* the "standard" MMU. So it is now actively confusing
to use it, because it implies that code is disabled or inactive when
the Radix MMU is in use, however that is not necessarily true.
So s/CONFIG_PPC_STD_MMU_64/CONFIG_PPC_BOOK3S_64/, and do some minor
formatting updates of some of the affected lines.
This will be a pain for backports, but c'est la vie.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The last user of CPU_FTR_ICSWX was removed in commit
6ff4d3e966 ("powerpc: Remove old unused icswx based coprocessor
support"), so free the bit up for future use.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When returning from an exception to a soft-enabled context, pending
IRQs are replayed but IRQ tracing is not reset, so a number of them
can get chained together into the same IRQ-disabled trace.
Fix this by having __check_irq_replay re-set IRQ trace. This is
conceptually where we respond to the next interrupt, so it fits the
semantics of the IRQ tracer.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the host takes a system reset interrupt while a guest is running,
the CPU must exit the guest before processing the host exception
handler.
After this patch, taking a sysrq+x with a CPU running in a guest
gives a trace like this:
cpu 0x27: Vector: 100 (System Reset) at [c000000fdf5776f0]
pc: c008000010158b80: kvmppc_run_core+0x16b8/0x1ad0 [kvm_hv]
lr: c008000010158b80: kvmppc_run_core+0x16b8/0x1ad0 [kvm_hv]
sp: c000000fdf577850
msr: 9000000002803033
current = 0xc000000fdf4b1e00
paca = 0xc00000000fd4d680 softe: 3 irq_happened: 0x01
pid = 6608, comm = qemu-system-ppc
Linux version 4.14.0-rc7-01489-g47e1893a404a-dirty #26 SMP
[c000000fdf577a00] c008000010159dd4 kvmppc_vcpu_run_hv+0x3dc/0x12d0 [kvm_hv]
[c000000fdf577b30] c0080000100a537c kvmppc_vcpu_run+0x44/0x60 [kvm]
[c000000fdf577b60] c0080000100a1ae0 kvm_arch_vcpu_ioctl_run+0x118/0x310 [kvm]
[c000000fdf577c00] c008000010093e98 kvm_vcpu_ioctl+0x530/0x7c0 [kvm]
[c000000fdf577d50] c000000000357bf8 do_vfs_ioctl+0xd8/0x8c0
[c000000fdf577df0] c000000000358448 SyS_ioctl+0x68/0x100
[c000000fdf577e30] c00000000000b220 system_call+0x58/0x6c
--- Exception: c01 (System Call) at 00007fff76868df0
SP (7fff7069baf0) is in userspace
Fixes: e36d0a2ed5 ("powerpc/powernv: Implement NMI IPI with OPAL_SIGNAL_SYSTEM_RESET")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A fix to the handling of misaligned paste instructions (P9 only), where a change
to a #define has caused the check for the instruction to always fail.
The preempt handling was unbalanced in the radix THP flush (P9 only). Though we
don't generally use preempt we want to keep it working as much as possible.
Two fixes for IMC (P9 only), one when booting with restricted number of CPUs and
one in the error handling when initialisation fails due to firmware etc.
A revert to fix function_graph on big endian machines, and then a rework of the
reverted patch to fix kprobes blacklist handling on big endian machines.
Thanks to:
Anju T Sudhakar, Guilherme G. Piccoli, Madhavan Srinivasan, Naveen N. Rao,
Nicholas Piggin, Paul Mackerras.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vTi1
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 4.14.
This is bigger than I like to send at rc7, but that's at least partly
because I didn't send any fixes last week. If it wasn't for the IMC
driver, which is new and getting heavy testing, the diffstat would
look a bit better. I've also added ftrace on big endian to my test
suite, so we shouldn't break that again in future.
- A fix to the handling of misaligned paste instructions (P9 only),
where a change to a #define has caused the check for the
instruction to always fail.
- The preempt handling was unbalanced in the radix THP flush (P9
only). Though we don't generally use preempt we want to keep it
working as much as possible.
- Two fixes for IMC (P9 only), one when booting with restricted
number of CPUs and one in the error handling when initialisation
fails due to firmware etc.
- A revert to fix function_graph on big endian machines, and then a
rework of the reverted patch to fix kprobes blacklist handling on
big endian machines.
Thanks to: Anju T Sudhakar, Guilherme G. Piccoli, Madhavan Srinivasan,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras"
* tag 'powerpc-4.14-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/perf: Fix core-imc hotplug callback failure during imc initialization
powerpc/kprobes: Dereference function pointers only if the address does not belong to kernel text
Revert "powerpc64/elfv1: Only dereference function descriptor for non-text symbols"
powerpc/64s/radix: Fix preempt imbalance in TLB flush
powerpc: Fix check for copy/paste instructions in alignment handler
powerpc/perf: Fix IMC allocation routine
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ9kEFAAoJEHm+PkMAQRiGw6wH/0j197qyGd0hkVFMJO6LAgN3
KQWS4nZ5BkVDocwv0RVnUJTtXqU1eozFgdVEtSoaFXpzlHGuptR2Tau9efDCJ7w3
/utZxqvhGebZd2T+j+/o/LE8BRQxhADBNJq2D/o0WNt8ecxuG0GIkhkEYt/o3z1v
/sxlwVwzXB7Dc/h1WcgGJG7cS6L9KzzAzGAS/iNvdFrPOygHBv8c0MxVZIiBIeeK
1nZdyvbyM8uenSyG+prGt9ENrqXZxxfwUxIchi2V7A9m1WmD5zijNkf1JCWji/O+
UsA1auxna7MwoxjxqZuGm4MlKOwZ+8xutk4JGgc+aP/ulndJbJYu+4op/3vaFBM=
=Mhx+
-----END PGP SIGNATURE-----
Backmerge tag 'v4.14-rc7' into drm-next
Linux 4.14-rc7
Requested by Ben Skeggs for nouveau to avoid major conflicts,
and things were getting a bit conflicty already, esp around amdgpu
reverts.
This makes the changes introduced in commit 83e840c770
("powerpc64/elfv1: Only dereference function descriptor for non-text
symbols") to be specific to the kprobe subsystem.
We previously changed ppc_function_entry() to always check the provided
address to confirm if it needed to be dereferenced. This is actually
only an issue for kprobe blacklisted asm labels (through use of
_ASM_NOKPROBE_SYMBOL) and can cause other issues with ftrace. Also, the
additional checks are not really necessary for our other uses.
As such, move this check to the kprobes subsystem.
Fixes: 83e840c770 ("powerpc64/elfv1: Only dereference function descriptor for non-text symbols")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch removes the restriction that a radix host can only run
radix guests, allowing us to run HPT (hashed page table) guests as
well. This is useful because it provides a way to run old guest
kernels that know about POWER8 but not POWER9.
Unfortunately, POWER9 currently has a restriction that all threads
in a given code must either all be in HPT mode, or all in radix mode.
This means that when entering a HPT guest, we have to obtain control
of all 4 threads in the core and get them to switch their LPIDR and
LPCR registers, even if they are not going to run a guest. On guest
exit we also have to get all threads to switch LPIDR and LPCR back
to host values.
To make this feasible, we require that KVM not be in the "independent
threads" mode, and that the CPU cores be in single-threaded mode from
the host kernel's perspective (only thread 0 online; threads 1, 2 and
3 offline). That allows us to use the same code as on POWER8 for
obtaining control of the secondary threads.
To manage the LPCR/LPIDR changes required, we extend the kvm_split_info
struct to contain the information needed by the secondary threads.
All threads perform a barrier synchronization (where all threads wait
for every other thread to reach the synchronization point) on guest
entry, both before and after loading LPCR and LPIDR. On guest exit,
they all once again perform a barrier synchronization both before
and after loading host values into LPCR and LPIDR.
Finally, it is also currently necessary to flush the entire TLB every
time we enter a HPT guest on a radix host. We do this on thread 0
with a loop of tlbiel instructions.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the ppc-kvm topic branch of the powerpc tree to get the
commit that reverts the patch "KVM: PPC: Book3S HV: POWER9 does not
require secondary thread management". This is needed for subsequent
patches which will be applied on this branch.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Commit 07d2a628bc ("powerpc/64s: Avoid cpabort in context switch
when possible", 2017-06-09) changed the definition of PPC_INST_COPY
and in so doing inadvertently broke the check for copy/paste
instructions in the alignment fault handler. The check currently
matches no instructions.
This fixes it by ANDing both sides of the comparison with the mask.
Fixes: 07d2a628bc ("powerpc/64s: Avoid cpabort in context switch when possible")
Cc: stable@vger.kernel.org # v4.13+
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Back in 2008 we added support for "fast little-endian switch" in the
syscall path. This added a special case syscall number 0x1ebe, which
is caught very early in the system call exception and switches endian
with as little overhead as possible. See commit 745a14cc26
("[POWERPC] Add fast little-endian switch system call") for full
details.
Although it is fast, it's also completely non standard. The "syscall
number" is out of the range of normal syscalls, it can't be traced or
audited, and it's a bit of a wart. To the best of our knowledge it was
only used by one program, now long since discontinued.
So in an effort to shake out any current users, put it behind a config
option, and make it default n. If anyone *is* using it they can
quickly reinstate it with a rebuild, and we can flip it to default y.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Unfortunately userspace can construct a sigcontext which enables
suspend. Thus userspace can force Linux into a path where trechkpt is
executed.
This patch blocks this from happening on POWER9 by sanity checking
sigcontexts passed in.
ptrace doesn't have this problem as only MSR SE and BE can be changed
via ptrace.
This patch also adds a number of WARN_ON()s in case we ever enter
suspend when we shouldn't. This should not happen, but if it does the
symptoms are soft lockup warnings which are not obviously TM related,
so the WARN_ON()s should make it obvious what's happening.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some Power9 revisions can run in a mode where TM operates without
suspended state. If we find ourself on a CPU that might be in this
mode, we query OPAL to check, and if so we reenable TM in CPU
features, and enable a new user feature to signal to userspace that we
are in this mode.
We do not enable the "normal" user feature, PPC_FEATURE2_HTM, but we
do enable PPC_FEATURE2_HTM_NOSC because that indicates to userspace
that the kernel will abort transactions on syscall entry, which is
true regardless of the suspend mode.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently the kernel relies on firmware to inform it whether or not the
CPU supports HTM and as long as the kernel was built with
CONFIG_PPC_TRANSACTIONAL_MEM=y then it will allow userspace to make
use of the facility.
There may be situations where it would be advantageous for the kernel
to not allow userspace to use HTM, currently the only way to achieve
this is to recompile the kernel with CONFIG_PPC_TRANSACTIONAL_MEM=n.
This patch adds a simple commandline option so that HTM can be
disabled at boot time.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Simplify to a bool, move to prom.c, put doco in the right place.
Always disable, regardless of initial state, to avoid user confusion.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reverts commit 94a04bc25a.
In order to run HPT guests on a radix POWER9 host, we will have to run
the host in single-threaded mode, because POWER9 processors do not
currently support running some threads of a core in HPT mode while
others are in radix mode ("mixed mode").
That means that we will need the same mechanisms that are used on
POWER8 to make the secondary threads available to KVM, which were
disabled on POWER9 by commit 94a04bc25a.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch_spin_lock_flags() is an internal part of the spinlock implementation
and is no longer available when SMP=n and DEBUG_SPINLOCK=y, so the PPC
RTAS code fails to compile in this configuration:
arch/powerpc/kernel/rtas.c: In function 'lock_rtas':
>> arch/powerpc/kernel/rtas.c:81:2: error: implicit declaration of function 'arch_spin_lock_flags' [-Werror=implicit-function-declaration]
arch_spin_lock_flags(&rtas.lock, flags);
^~~~~~~~~~~~~~~~~~~~
Since there's no good reason to use arch_spin_lock_flags() here (the code
in question already calls local_irq_save(flags)), switch it over to
arch_spin_lock and get things building again.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1508327469-20231-1-git-send-email-will.deacon@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Daniel Axtens reported that on the HiSilicon D05 board, the VGA device is
behind a bridge that doesn't support PCI_BRIDGE_CTL_VGA, so the VGA arbiter
never selects it as the default, which means Xorg auto-detection doesn't
work.
VGA is a legacy PCI feature: a VGA device can respond to addresses, e.g.,
[mem 0xa0000-0xbffff], [io 0x3b0-0x3bb], [io 0x3c0-0x3df], etc., that are
not configurable by BARs. Consequently, multiple VGA devices can conflict
with each other. The VGA arbiter avoids conflicts by ensuring that those
legacy resources are only routed to one VGA device at a time.
The arbiter identifies the "default VGA" device, i.e., a legacy VGA device
that was used by boot firmware. It selects the first device that:
- is of PCI_CLASS_DISPLAY_VGA,
- has both PCI_COMMAND_IO and PCI_COMMAND_MEMORY enabled, and
- has PCI_BRIDGE_CTL_VGA set in all upstream bridges.
Some systems don't have such a device. For example, if a host bridge
doesn't support I/O space, PCI_COMMAND_IO probably won't be enabled for any
devices below it. Or, as on the HiSilicon D05, the VGA device may be
behind a bridge that doesn't support PCI_BRIDGE_CTL_VGA, so accesses to the
legacy VGA resources will never reach the device.
This patch extends the arbiter so that if it doesn't find a device that
meets all the above criteria, it selects the first device that:
- is of PCI_CLASS_DISPLAY_VGA and
- has PCI_COMMAND_IO or PCI_COMMAND_MEMORY enabled
If it doesn't find even that, it selects the first device that:
- is of class PCI_CLASS_DISPLAY_VGA.
Such a device may not be able to use the legacy VGA resources, but most
drivers can operate the device without those. Setting it as the default
device means its "boot_vga" sysfs file will contain "1", which Xorg (via
libpciaccess) uses to help select its default output device.
This fixes Xorg auto-detection on some arm64 systems (HiSilicon D05 in
particular; see the link below).
It also replaces the powerpc fixup_vga() quirk, albeit with slightly
different semantics: the quirk selected the first VGA device we found, and
overrode that selection with any enabled VGA device we found. If there
were several enabled VGA devices, the *last* one we found would become the
default.
The code here instead selects the *first* enabled VGA device we find, and
if none are enabled, the first VGA device we find.
Link: http://lkml.kernel.org/r/20170901072744.2409-1-dja@axtens.net
Tested-by: Daniel Axtens <dja@axtens.net> # arm64, ppc64-qemu-tcg
Tested-by: Zhou Wang <wangzhou1@hisilicon.com> # D05 Hisi Hip07, Hip08
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171013034721.14630.65913.stgit@bhelgaas-glaptop.roam.corp.google.com
If we are in user space and hit a UE error, we now have the
basic infrastructure to walk the page tables and find out
the effective address that was accessed, since the DAR
is not valid.
We use a work_queue content to hookup the bad pfn, any
other context causes problems, since memory_failure itself
can call into schedule() via lru_drain_ bits.
We could probably poison the struct page to avoid a race
between detection and taking corrective action.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Hookup instruction errors (UE) for memory offling via memory_failure()
in a manner similar to load/store errors (derror). Since we have access
to the NIP, the conversion is a one step process in this case.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Extract physical_address for UE errors by walking the page
tables for the mm and address at the NIP, to extract the
instruction. Then use the instruction to find the effective
address via analyse_instr().
We might have page table walking races, but we expect them to
be rare, the physical address extraction is best effort. The idea
is to then hook up this infrastructure to memory failure eventually.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the same alignment as Effective address.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are no users of get_mce_fault_addr() since commit
1363875bdb ("powerpc/64s: fix handling of non-synchronous machine
checks") removed the last usage.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A fix for a bad bug (written by me) in our livepatch handler. Removal of an
over-zealous lockdep_assert_cpus_held() in our topology code. A fix to the
recently added emulation of cntlz[wd]. And three small fixes to the recently
added IMC PMU driver.
Thanks to:
Anju T Sudhakar, Balbir Singh, Kamalesh Babulal, Naveen N. Rao, Sandipan Das,
Santosh Sivaraj, Thiago Jung Bauermann.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wWnt
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A fix for a bad bug (written by me) in our livepatch handler. Removal
of an over-zealous lockdep_assert_cpus_held() in our topology code. A
fix to the recently added emulation of cntlz[wd]. And three small
fixes to the recently added IMC PMU driver.
Thanks to: Anju T Sudhakar, Balbir Singh, Kamalesh Babulal, Naveen N.
Rao, Sandipan Das, Santosh Sivaraj, Thiago Jung Bauermann"
* tag 'powerpc-4.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/perf: Fix IMC initialization crash
powerpc/perf: Add ___GFP_NOWARN flag to alloc_pages_node()
powerpc/perf: Fix for core/nest imc call trace on cpuhotplug
powerpc: Don't call lockdep_assert_cpus_held() from arch_update_cpu_topology()
powerpc/lib/sstep: Fix count leading zeros instructions
powerpc/livepatch: Fix livepatch stack access
Use WARN_ON(), while running out of stubs in stub_for_addr()
and abort loading of the module instead of BUG_ON().
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
While running stress test with livepatch module loaded, kernel bug was
triggered.
cpu 0x5: Vector: 400 (Instruction Access) at [c0000000eb9d3b60]
5:mon> t
[c0000000eb9d3de0] c0000000eb9d3e30 (unreliable)
[c0000000eb9d3e30] c000000000008ab4 hardware_interrupt_common+0x114/0x120
--- Exception: 501 (Hardware Interrupt) at c000000000053040 livepatch_handler+0x4c/0x74
[c0000000eb9d4120] 0000000057ac6e9d (unreliable)
[d0000000089d9f78] 2e0965747962382e
SP (965747962342e09) is in userspace
When an interrupt occurs during the livepatch_handler execution, it's
possible for the livepatch_stack and/or thread_info to be corrupted.
eg:
Task A Interrupt Handler
========= =================
livepatch_handler:
mr r0, r1
ld r1, TI_livepatch_sp(r12)
hardware_interrupt_common:
do_IRQ+0x8:
mflr r0 <- saved stack pointer is overwritten
bl _mcount
...
std r27,-40(r1) <- overwrite of thread_info()
lis r2, STACK_END_MAGIC@h
ori r2, r2, STACK_END_MAGIC@l
ld r12, -8(r1)
Fix the corruption by using r11 register for livepatch stack
manipulation, instead of shuffling task stack and livepatch stack into
r1 register. Using r11 register also avoids disabling/enabling irq's
while setting up the livepatch stack.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge powerpc transactional memory fixes from Michael Ellerman:
"I figured I'd still send you the commits using a bundle to make sure
it works in case I need to do it again in future"
This fixes transactional memory state restore for powerpc.
* bundle'd patches from Michael Ellerman:
powerpc/tm: Fix illegal TM state in signal handler
powerpc/64s: Use emergency stack for kernel TM Bad Thing program checks
Nine small fixes, really nothing that stands out.
A work around for a spurious MCE on Power9. A CXL fault handling fix, some fixes
to the new XIVE code, and a fix to the new 32-bit STRICT_KERNEL_RWX code.
Fixes for old code/stable: an fix to an incorrect TLB flush on boot but not on
any current machines, a compile error on 4xx and a fix to memory hotplug when
using radix (Power9).
Thanks to:
Anton Blanchard, Cédric Le Goater, Christian Lamparter, Christophe Leroy,
Christophe Lombard, Guenter Roeck, Jeremy Kerr, Michael Neuling, Nicholas
Piggin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZ11/yAAoJEFHr6jzI4aWAooYQAKjOKamLyxRotFGSqBfrfOMN
UfWKAmfeoF/gi4z03x8JdhcMQ1CMh5c/cQmrwzkzDosQ2m83CEWzNbk0gFV0Tpld
2qDTrEnBfTC4TRhCwWuOlaQC8LFeqxwpsCS6iXGpYoTY2NzmsbliPIQaruCIqj3f
F+7etfTqGJ+gCCkGfT0s7m96QO+daaT32nXL1VM8i/rOOpwZ23oj6kR3/ZSTWxBc
eyzvUcTLLhLp8hJoF0kU4f1VQtYijnpqK6ULr3wSfxYqjB9S4dsGyiF537aw5bKX
UPUCoMgkttVy8Jh35dtvKLuMqlfjHGqoe6UcezSG9a6wxeUnQRzsVmXihNDSkyEt
EawmPS6R5YaXXu9NKsleKBZDAdU4+EkcX24Wwn/lZy3wTKc1Lys+wH9hXuzzGNiH
JYEcMacXvpM1yFYNT+ouyLtoT86VWVCdwihueBMV74lyV87Wr55zS65XP6Z+Bb8/
aPL906sOAvnJW1JhHbYq/UxLfvs0enHNHpyR0xM4/oXi+RoGfhbM/MC1uJxv4w9z
12n1hbrpaRxHSSnJr1gahCrDoNUXLjkO2+0Ur3iXP4tfMMhwDs8qCILeaKpNmzkC
sO1ehOmXSSYqJLNiPmSIxs/QEzjFrvQdNwZOIav+3Tsc5ofR6wsauDCmfK5br2Mg
BdhW7LXtqL77cmOzN95e
=etbe
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Nine small fixes, really nothing that stands out.
A work-around for a spurious MCE on Power9. A CXL fault handling fix,
some fixes to the new XIVE code, and a fix to the new 32-bit
STRICT_KERNEL_RWX code.
Fixes for old code/stable: an fix to an incorrect TLB flush on boot
but not on any current machines, a compile error on 4xx and a fix to
memory hotplug when using radix (Power9).
Thanks to: Anton Blanchard, Cédric Le Goater, Christian Lamparter,
Christophe Leroy, Christophe Lombard, Guenter Roeck, Jeremy Kerr,
Michael Neuling, Nicholas Piggin"
* tag 'powerpc-4.14-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Increase memory block size to 1GB on radix
powerpc/mm: Call flush_tlb_kernel_range with interrupts enabled
powerpc/xive: Clear XIVE internal structures when a CPU is removed
powerpc/xive: Fix IPI reset
powerpc/4xx: Fix compile error with 64K pages on 40x, 44x
powerpc: Fix action argument for cpufeatures-based TLB flush
cxl: Fix memory page not handled
powerpc: Fix workaround for spurious MCE on POWER9
powerpc: Handle MCE on POWER9 with only DSISR bit 30 set
Pull watchddog clean-up and fixes from Thomas Gleixner:
"The watchdog (hard/softlockup detector) code is pretty much broken in
its current state. The patch series addresses this by removing all
duct tape and refactoring it into a workable state.
The reasons why I ask for inclusion that late in the cycle are:
1) The code causes lockdep splats vs. hotplug locking which get
reported over and over. Unfortunately there is no easy fix.
2) The risk of breakage is minimal because it's already broken
3) As 4.14 is a long term stable kernel, I prefer to have working
watchdog code in that and the lockdep issues resolved. I wouldn't
ask you to pull if 4.14 wouldn't be a LTS kernel or if the
solution would be easy to backport.
4) The series was around before the merge window opened, but then got
delayed due to the UP failure caused by the for_each_cpu()
surprise which we discussed recently.
Changes vs. V1:
- Addressed your review points
- Addressed the warning in the powerpc code which was discovered late
- Changed two function names which made sense up to a certain point
in the series. Now they match what they do in the end.
- Fixed a 'unused variable' warning, which got not detected by the
intel robot. I triggered it when trying all possible related config
combinations manually. Randconfig testing seems not random enough.
The changes have been tested by and reviewed by Don Zickus and tested
and acked by Micheal Ellerman for powerpc"
* 'core-watchdog-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
watchdog/core: Put softlockup_threads_initialized under ifdef guard
watchdog/core: Rename some softlockup_* functions
powerpc/watchdog: Make use of watchdog_nmi_probe()
watchdog/core, powerpc: Lock cpus across reconfiguration
watchdog/core, powerpc: Replace watchdog_nmi_reconfigure()
watchdog/hardlockup/perf: Fix spelling mistake: "permanetely" -> "permanently"
watchdog/hardlockup/perf: Cure UP damage
watchdog/hardlockup: Clean up hotplug locking mess
watchdog/hardlockup/perf: Simplify deferred event destroy
watchdog/hardlockup/perf: Use new perf CPU enable mechanism
watchdog/hardlockup/perf: Implement CPU enable replacement
watchdog/hardlockup/perf: Implement init time detection of perf
watchdog/hardlockup/perf: Implement init time perf validation
watchdog/core: Get rid of the racy update loop
watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage
watchdog/sysctl: Clean up sysctl variable name space
watchdog/sysctl: Get rid of the #ifdeffery
watchdog/core: Clean up header mess
watchdog/core: Further simplify sysctl handling
watchdog/core: Get rid of the thread teardown/setup dance
...
Currently it's possible that on returning from the signal handler
through the restore_tm_sigcontexts() code path (e.g. from a signal
caught due to a `trap` instruction executed in the middle of an HTM
block, or a deliberately constructed sigframe) an illegal TM state
(like TS=10 TM=0, i.e. "T0") is set in SRR1 and when `rfid` sets
implicitly the MSR register from SRR1 register on return to userspace
it causes a TM Bad Thing exception.
That illegal state can be set (a) by a malicious user that disables
the TM bit by tweaking the bits in uc_mcontext before returning from
the signal handler or (b) by a sufficient number of context switches
occurring such that the load_tm counter overflows and TM is disabled
whilst in the signal handler.
This commit fixes the illegal TM state by ensuring that TM bit is
always enabled before we return from restore_tm_sigcontexts(). A small
comment correction is made as well.
Fixes: 5d176f751e ("powerpc: tm: Enable transactional memory (TM) lazily for userspace")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When using transactional memory (TM), the CPU can be in one of six
states as far as TM is concerned, encoded in the Machine State
Register (MSR). Certain state transitions are illegal and if attempted
trigger a "TM Bad Thing" type program check exception.
If we ever hit one of these exceptions it's treated as a bug, ie. we
oops, and kill the process and/or panic, depending on configuration.
One case where we can trigger a TM Bad Thing, is when returning to
userspace after a system call or interrupt, using RFID. When this
happens the CPU first restores the user register state, in particular
r1 (the stack pointer) and then attempts to update the MSR. However
the MSR update is not allowed and so we take the program check with
the user register state, but the kernel MSR.
This tricks the exception entry code into thinking we have a bad
kernel stack pointer, because the MSR says we're coming from the
kernel, but r1 is pointing to userspace.
To avoid this we instead always switch to the emergency stack if we
take a TM Bad Thing from the kernel. That way none of the user
register values are used, other than for printing in the oops message.
This is the fix for CVE-2017-1000255.
Fixes: 5d176f751e ("powerpc: tm: Enable transactional memory (TM) lazily for userspace")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
[mpe: Rewrite change log & comments, tweak asm slightly]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a check for p->state == TASK_RUNNING so that any wake-ups on
task_struct p in the interim lead to 0 being returned by get_wchan().
Signed-off-by: Kautuk Consul <kautuk.consul.1980@gmail.com>
[mpe: Confirmed other architectures do similar]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The "reset" argument passed to pci_iov_add_virtfn() and
pci_iov_remove_virtfn() is always zero since 46cb7b1bd8 ("PCI: Remove
unused SR-IOV VF Migration support")
Remove the argument together with the associated code.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Fix a circa 2005 FIXME by implementing a check to ensure that we
actually got into the jprobe break handler() due to the trap in
jprobe_return().
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Kamalesh pointed out that we are getting the below call traces with
livepatched functions when we enable CONFIG_PREEMPT:
[ 495.470721] BUG: using __this_cpu_read() in preemptible [00000000] code: cat/8394
[ 495.471167] caller is is_current_kprobe_addr+0x30/0x90
[ 495.471171] CPU: 4 PID: 8394 Comm: cat Tainted: G K 4.13.0-rc7-nnr+ #95
[ 495.471173] Call Trace:
[ 495.471178] [c00000008fd9b960] [c0000000009f039c] dump_stack+0xec/0x160 (unreliable)
[ 495.471184] [c00000008fd9b9a0] [c00000000059169c] check_preemption_disabled+0x15c/0x170
[ 495.471187] [c00000008fd9ba30] [c000000000046460] is_current_kprobe_addr+0x30/0x90
[ 495.471191] [c00000008fd9ba60] [c00000000004e9a0] ftrace_call+0x1c/0xb8
[ 495.471195] [c00000008fd9bc30] [c000000000376fd8] seq_read+0x238/0x5c0
[ 495.471199] [c00000008fd9bcd0] [c0000000003cfd78] proc_reg_read+0x88/0xd0
[ 495.471203] [c00000008fd9bd00] [c00000000033e5d4] __vfs_read+0x44/0x1b0
[ 495.471206] [c00000008fd9bd90] [c0000000003402ec] vfs_read+0xbc/0x1b0
[ 495.471210] [c00000008fd9bde0] [c000000000342138] SyS_read+0x68/0x110
[ 495.471214] [c00000008fd9be30] [c00000000000bc6c] system_call+0x58/0x6c
Commit c05b8c4474 ("powerpc/kprobes: Skip livepatch_handler() for
jprobes") introduced a helper is_current_kprobe_addr() to help determine
if the current function has been livepatched or if it has a jprobe
installed, both of which modify the NIP. This was subsequently renamed
to __is_active_jprobe().
In the case of a jprobe, kprobe_ftrace_handler() disables pre-emption
before calling into setjmp_pre_handler() which returns without disabling
pre-emption. This is done to ensure that the jprobe handler won't
disappear beneath us if the jprobe is unregistered between the
setjmp_pre_handler() and the subsequent longjmp_break_handler() called
from the jprobe handler. Due to this, we can use __this_cpu_read() in
__is_active_jprobe() with the pre-emption check as we know that
pre-emption will be disabled.
However, if this function has been livepatched, we are still doing this
check and when we do so, pre-emption won't necessarily be disabled. This
results in the call trace shown above.
Fix this by only invoking __is_active_jprobe() when pre-emption is
disabled. And since we now guard this within a pre-emption check, we can
instead use raw_cpu_read() to get the current_kprobe value skipping the
check done by __this_cpu_read().
Fixes: c05b8c4474 ("powerpc/kprobes: Skip livepatch_handler() for jprobes")
Reported-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Tested-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit c05b8c4474 ("powerpc/kprobes: Skip livepatch_handler() for
jprobes"), we added a helper is_current_kprobe_addr() to help detect if
the modified regs->nip was due to a jprobe or livepatch. Masami felt
that the function name was not quite clear. To that end, this patch
renames is_current_kprobe_addr() to __is_active_jprobe() and adds a
comment to (hopefully) better clarify the purpose of this helper. The
helper has also now been moved to kprobes-ftrace.c so that it is only
available for KPROBES_ON_FTRACE.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, we disable instruction emulation if emulate_step() fails for
any reason. However, such failures could be transient and specific to a
particular run. Instead, only disable instruction emulation if we have
never been able to emulate this. If we had emulated this instruction
successfully at least once, then we single step only this probe hit and
continue to try emulating the instruction in subsequent probe hits.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
1. This is only used in kprobes.c, so make it static.
2. Remove the un-necessary (ret == 0) comparison in the else clause.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The rework of the core hotplug code triggers the WARN_ON in start_wd_cpu()
on powerpc because it is called multiple times for the boot CPU.
The first call is via:
start_wd_on_cpu+0x80/0x2f0
watchdog_nmi_reconfigure+0x124/0x170
softlockup_reconfigure_threads+0x110/0x130
lockup_detector_init+0xbc/0xe0
kernel_init_freeable+0x18c/0x37c
kernel_init+0x2c/0x160
ret_from_kernel_thread+0x5c/0xbc
And then again via the CPU hotplug registration:
start_wd_on_cpu+0x80/0x2f0
cpuhp_invoke_callback+0x194/0x620
cpuhp_thread_fun+0x7c/0x1b0
smpboot_thread_fn+0x290/0x2a0
kthread+0x168/0x1b0
ret_from_kernel_thread+0x5c/0xbc
This can be avoided by setting up the cpu hotplug state with nocalls and
move the initialization to the watchdog_nmi_probe() function. That
initializes the hotplug callbacks without invoking the callback and the
following core initialization function then configures the watchdog for the
online CPUs (in this case CPU0) via softlockup_reconfigure_threads().
Reported-and-tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Instead of dropping the cpu hotplug lock after stopping NMI watchdog and
threads and reaquiring for restart, the code and the protection rules
become more obvious when holding cpu hotplug lock across the full
reconfiguration.
Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710022105570.2114@nanos
The recent cleanup of the watchdog code split watchdog_nmi_reconfigure()
into two stages. One to stop the NMI and one to restart it after
reconfiguration. That was done by adding a boolean 'run' argument to the
code, which is functionally correct but not necessarily a piece of art.
Replace it by two explicit functions: watchdog_nmi_stop() and
watchdog_nmi_start().
Fixes: 6592ad2fcc ("watchdog/core, powerpc: Make watchdog_nmi_reconfigure() two stage")
Requested-by: Linus 'Nursing his pet-peeve' Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Thomas 'Mopping up garbage' Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1710021957480.2114@nanos
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This code is used at boot and machine checks, so it should be using
early_radix_enabled() (which is usable any time).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is possible to wake from idle due to a system reset exception, in
which case the CPU takes a system reset interrupt to wake from idle,
with system reset as the wakeup reason.
The regular (not idle wakeup) system reset interrupt handler must be
invoked in this case, otherwise the system reset interrupt is lost.
Handle the system reset interrupt immediately after CPU state has been
restored.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In xmon, touch_nmi_watchdog() is not expected to be checking that
other CPUs have not touched the watchdog, so the code will just call
touch_nmi_watchdog() once before re-enabling hard interrupts.
Just update our CPU's state, and ignore apparently stuck SMP threads.
Arguably touch_nmi_watchdog should check for SMP lockups, and callers
should be fixed, but that's not trivial for the input code of xmon.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If sysctl_hardlockup_all_cpu_backtrace is enabled, there is no need to
IPI stuck CPUs for backtrace before trigger_allbutself_cpu_backtrace(),
which does the same thing again.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The SMP watchdog will detect locked CPUs and IPI them to print a
backtrace and registers. If panic on hard lockup is enabled, do not
panic from this handler, because that can cause recursion into the IPI
layer during the panic.
The caller already panics in this case.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The mmu context on the 40x, 44x does not define pte_frag entry. This
causes gcc abort the compilation due to:
setup-common.c: In function ‘setup_arch’:
setup-common.c:908: error: ‘mm_context_t’ has no ‘pte_frag’
This patch fixes the issue by removing the pte_frag initialization in
setup-common.c.
This is possible, because the compiler will do the initialization,
since the mm_context is a sub struct of init_mm. init_mm is declared
in mm_types.h as external linkage.
According to C99 6.2.4.3:
An object whose identifier is declared with external linkage
[...] has static storage duration.
C99 defines in 6.7.8.10 that:
If an object that has static storage duration is not
initialized explicitly, then:
- if it has pointer type, it is initialized to a null pointer
Fixes: b1923caa6e ("powerpc: Merge 32-bit and 64-bit setup_arch()")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 41d0c2ecde ("powerpc/powernv: Fix local TLB flush for boot
and MCE on POWER9") introduced calls to __flush_tlb_power[89] from the
cpufeatures code, specifying the number of sets to flush.
However, these functions take an action argument, not a number of
sets. This means we hit the BUG() in __flush_tlb_{206,300} when using
cpufeatures-style configuration.
This change passes TLB_INVAL_SCOPE_GLOBAL instead.
Fixes: 41d0c2ecde ("powerpc/powernv: Fix local TLB flush for boot and MCE on POWER9")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the recent commit d8bd9f3f09 ("powerpc: Handle MCE on POWER9 with
only DSISR bit 30 set") I screwed up the bit number. It should be bit
25 (IBM bit 38).
Fixes: d8bd9f3f09 ("powerpc: Handle MCE on POWER9 with only DSISR bit 30 set")
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD2.1 and earlier has an issue where some cache inhibited
vector load will return bad data. The workaround is two part, one
firmware/microcode part triggers HMI interrupts when hitting such
loads, the other part is this patch which then emulates the
instructions in Linux.
The affected instructions are limited to lxvd2x, lxvw4x, lxvb16x and
lxvh8x.
When an instruction triggers the HMI, all threads in the core will be
sent to the HMI handler, not just the one running the vector load.
In general, these spurious HMIs are detected by the emulation code and
we just return back to the running process. Unfortunately, if a
spurious interrupt occurs on a vector load that's to normal memory we
have no way to detect that it's spurious (unless we walk the page
tables, which is very expensive). In this case we emulate the load but
we need do so using a vector load itself to ensure 128bit atomicity is
preserved.
Some additional debugfs emulated instruction counters are added also.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Switch CONFIG_PPC_BOOK3S_64 to CONFIG_VSX to unbreak the build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9 DD2.1 and below, it's possible for a paste instruction to
cause a Machine Check Exception (MCE) where only DSISR bit 30 (IBM 33)
is set. This will result in the MCE handler seeing an unknown event,
which triggers linux to crash.
We change this by detecting unknown events caused by load/stores in
the MCE handler and marking them as handled so that we no longer
crash.
An MCE that occurs like this is spurious, so we don't need to do
anything in terms of servicing it. If there is something that needs to
be serviced, the CPU will raise the MCE again with the correct DSISR
so that it can be serviced properly.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com
Acked-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Expand comment with details from change log, use normal bit #s]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the post_init callback which is only used
by powernv, we can just call it explicitly from
the powernv code.
This partially kills the ability to "disable" eeh at
runtime via debugfs as this was calling that same
callback again, but this is both unused and broken
in several ways. If we want to revive it, we need
to create a dedicated enable/disable callback on the
backend that does the right thing.
Let the bulk of eeh initialize normally at
core_initcall() like it does on pseries by removing
the hack in eeh_init() that delays it.
Instead we make sure our eeh->probe cleanly bails
out of the PEs haven't been created yet and we force
a re-probe where we used to call eeh_init() again.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Otherwise we end up not yet having computed the right diag data size
on powernv where EEH initialization is delayed, thus causing memory
corruption later on when calling OPAL.
Fixes: 5cb1f8fddd ("powerpc/powernv/pci: Dynamically allocate PHB diag data")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Optprobes depended on an updated regs->nip from analyse_instr() to
identify the location to branch back from the optprobes trampoline.
However, since commit 3cdfcbfd32 ("powerpc: Change analyse_instr so
it doesn't modify *regs"), analyse_instr() doesn't update the registers
anymore. Due to this, we end up branching back from the optprobes
trampoline to the same branch into the trampoline resulting in a loop.
Fix this by calling out to emulate_update_regs() before using the nip.
Additionally, explicitly compare the return value from analyse_instr()
to 1, rather than just checking for !0 so as to guard against any
future changes to analyse_instr() that may result in -1 being returned
in more scenarios.
Fixes: 3cdfcbfd32 ("powerpc: Change analyse_instr so it doesn't modify *regs")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit cd63f3c ("powerpc/tm: Fix saving of TM SPRs in core dump")
added code to access TM SPRs in flush_tmregs_to_thread(). However
flush_tmregs_to_thread() does not check if TM feature is available on
CPU before trying to access TM SPRs in order to copy live state to
thread structures. flush_tmregs_to_thread() is indeed guarded by
CONFIG_PPC_TRANSACTIONAL_MEM but it might be the case that kernel
was compiled with CONFIG_PPC_TRANSACTIONAL_MEM enabled and ran on
a CPU without TM feature available, thus rendering the execution
of TM instructions that are treated by the CPU as illegal instructions.
The fix is just to add proper checking in flush_tmregs_to_thread()
if CPU has the TM feature before accessing any TM-specific resource,
returning immediately if TM is no available on the CPU. Adding
that checking in flush_tmregs_to_thread() instead of in places
where it is called, like in vsr_get() and vsr_set(), is better because
avoids the same problem cropping up elsewhere.
Cc: stable@vger.kernel.org # v4.13+
Fixes: cd63f3c ("powerpc/tm: Fix saving of TM SPRs in core dump")
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Just one fix, for the handling of alignment interrupts on dcbz instructions.
Thanks to:
Paul Mackerras, Christian Zigotzky, Michal Sojka.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=F9yZ
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"Just one fix, for the handling of alignment interrupts on dcbz
instructions.
Thanks to Paul Mackerras, Christian Zigotzky, Michal Sojka"
* tag 'powerpc-4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Fix handling of alignment interrupt on dcbz instruction
This fixes the emulation of the dcbz instruction in the alignment
interrupt handler. The error was that we were comparing just the
instruction type field of op.type rather than the whole thing,
and therefore the comparison "type != CACHEOP + DCBZ" was always
true.
Fixes: 31bfdb036f ("powerpc: Use instruction emulation infrastructure to handle alignment faults")
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Tested-by: Michal Sojka <sojkam1@fel.cvut.cz>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All watchdog thread related functions are delegated to the smpboot thread
infrastructure, which handles serialization against CPU hotplug correctly.
The sysctl interface is completely decoupled from anything which requires
CPU hotplug protection.
No need to protect the sysctl writes against cpu hotplug anymore. Remove it
and add the now required protection to the powerpc arch_nmi_watchdog
implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20170912194148.418497420@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Both the perf reconfiguration and the powerpc watchdog_nmi_reconfigure()
need to be done in two steps.
1) Stop all NMIs
2) Read the new parameters and start NMIs
Right now watchdog_nmi_reconfigure() is a combination of both. To allow a
clean reconfiguration add a 'run' argument and split the functionality in
powerpc.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20170912194147.862865570@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This interface has several issues:
- It's causing recursive locking of the hotplug lock.
- It's complete overkill to teardown all threads and then recreate them
The same can be achieved with the simple hardlockup_detector_perf_stop /
restart() interfaces. The abuse from the busy looping poweroff() loop of
PARISC has been solved as well.
Remove the cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Link: http://lkml.kernel.org/r/20170912194146.487537732@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
GFP_TEMPORARY was introduced by commit e12ba74d8f ("Group short-lived
and reclaimable kernel allocations") along with __GFP_RECLAIMABLE. It's
primary motivation was to allow users to tell that an allocation is
short lived and so the allocator can try to place such allocations close
together and prevent long term fragmentation. As much as this sounds
like a reasonable semantic it becomes much less clear when to use the
highlevel GFP_TEMPORARY allocation flag. How long is temporary? Can the
context holding that memory sleep? Can it take locks? It seems there is
no good answer for those questions.
The current implementation of GFP_TEMPORARY is basically GFP_KERNEL |
__GFP_RECLAIMABLE which in itself is tricky because basically none of
the existing caller provide a way to reclaim the allocated memory. So
this is rather misleading and hard to evaluate for any benefits.
I have checked some random users and none of them has added the flag
with a specific justification. I suspect most of them just copied from
other existing users and others just thought it might be a good idea to
use without any measuring. This suggests that GFP_TEMPORARY just
motivates for cargo cult usage without any reasoning.
I believe that our gfp flags are quite complex already and especially
those with highlevel semantic should be clearly defined to prevent from
confusion and abuse. Therefore I propose dropping GFP_TEMPORARY and
replace all existing users to simply use GFP_KERNEL. Please note that
SLAB users with shrinkers will still get __GFP_RECLAIMABLE heuristic and
so they will be placed properly for memory fragmentation prevention.
I can see reasons we might want some gfp flag to reflect shorterm
allocations but I propose starting from a clear semantic definition and
only then add users with proper justification.
This was been brought up before LSF this year by Matthew [1] and it
turned out that GFP_TEMPORARY really doesn't have a clear semantic. It
seems to be a heuristic without any measured advantage for most (if not
all) its current users. The follow up discussion has revealed that
opinions on what might be temporary allocation differ a lot between
developers. So rather than trying to tweak existing users into a
semantic which they haven't expected I propose to simply remove the flag
and start from scratch if we really need a semantic for short term
allocations.
[1] http://lkml.kernel.org/r/20170118054945.GD18349@bombadil.infradead.org
[akpm@linux-foundation.org: fix typo]
[akpm@linux-foundation.org: coding-style fixes]
[sfr@canb.auug.org.au: drm/i915: fix up]
Link: http://lkml.kernel.org/r/20170816144703.378d4f4d@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170728091904.14627-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull namespace updates from Eric Biederman:
"Life has been busy and I have not gotten half as much done this round
as I would have liked. I delayed it so that a minor conflict
resolution with the mips tree could spend a little time in linux-next
before I sent this pull request.
This includes two long delayed user namespace changes from Kirill
Tkhai. It also includes a very useful change from Serge Hallyn that
allows the security capability attribute to be used inside of user
namespaces. The practical effect of this is people can now untar
tarballs and install rpms in user namespaces. It had been suggested to
generalize this and encode some of the namespace information
information in the xattr name. Upon close inspection that makes the
things that should be hard easy and the things that should be easy
more expensive.
Then there is my bugfix/cleanup for signal injection that removes the
magic encoding of the siginfo union member from the kernel internal
si_code. The mips folks reported the case where I had used FPE_FIXME
me is impossible so I have remove FPE_FIXME from mips, while at the
same time including a return statement in that case to keep gcc from
complaining about unitialized variables.
I almost finished the work to get make copy_siginfo_to_user a trivial
copy to user. The code is available at:
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace.git neuter-copy_siginfo_to_user-v3
But I did not have time/energy to get the code posted and reviewed
before the merge window opened.
I was able to see that the security excuse for just copying fields
that we know are initialized doesn't work in practice there are buggy
initializations that don't initialize the proper fields in siginfo. So
we still sometimes copy unitialized data to userspace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
Introduce v3 namespaced file capabilities
mips/signal: In force_fcr31_sig return in the impossible case
signal: Remove kernel interal si_code magic
fcntl: Don't use ambiguous SIG_POLL si_codes
prctl: Allow local CAP_SYS_ADMIN changing exe_file
security: Use user_namespace::level to avoid redundant iterations in cap_capable()
userns,pidns: Verify the userns for new pid namespaces
signal/testing: Don't look for __SI_FAULT in userspace
signal/mips: Document a conflict with SI_USER with SIGFPE
signal/sparc: Document a conflict with SI_USER with SIGFPE
signal/ia64: Document a conflict with SI_USER with SIGFPE
signal/alpha: Document a conflict with SI_USER for SIGTRAP
First, number of CPUs can't be negative number.
Second, different signnnedness leads to suboptimal code in the following
cases:
1)
kmalloc(nr_cpu_ids * sizeof(X));
"int" has to be sign extended to size_t.
2)
while (loff_t *pos < nr_cpu_ids)
MOVSXD is 1 byte longed than the same MOV.
Other cases exist as well. Basically compiler is told that nr_cpu_ids
can't be negative which can't be deduced if it is "int".
Code savings on allyesconfig kernel: -3KB
add/remove: 0/0 grow/shrink: 25/264 up/down: 261/-3631 (-3370)
function old new delta
coretemp_cpu_online 450 512 +62
rcu_init_one 1234 1272 +38
pci_device_probe 374 399 +25
...
pgdat_reclaimable_pages 628 556 -72
select_fallback_rq 446 369 -77
task_numa_find_cpu 1923 1807 -116
Link: http://lkml.kernel.org/r/20170819114959.GA30580@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On POWER9, the Client Architecture Support (CAS) negotiation process
determines whether the guest operates in XIVE Legacy compatibility or
in XIVE exploitation mode. Now that we have initial guest support for
the XIVE interrupt controller, let's inform the hypervisor what we can
do.
The platform advertises the XIVE Exploitation Mode support using the
property "ibm,arch-vec-5-platform-support-vec-5", byte 23 bits 0-1 :
- 0b00 XIVE legacy mode Only
- 0b01 XIVE exploitation mode Only
- 0b10 XIVE legacy or exploitation mode
The OS asks for XIVE Exploitation Mode support using the property
"ibm,architecture-vec-5", byte 23 bits 0-1:
- 0b00 XIVE legacy mode Only
- 0b01 XIVE exploitation mode Only
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use DEVICE_ATTR_RW for read-write attributes. This simplifies the
source code, improves readbility, and reduces the chance of
inconsistencies.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Omit an extra message for a memory allocation failure in
eeh_dev_init().
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[mpe: Do not drop the message that can happen at runtime and lead to
an event not being handled]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
memset() is patched after initialisation to activate the
optimised part which uses cache instructions.
Today we have a 'b 2f' to skip the optimised patch, which then gets
replaced by a NOP, implying a useless cycle consumption.
As we have a 'bne 2f' just before, we could use that instruction
for the live patching, hence removing the need to have a
dedicated 'b 2f' to be replaced by a NOP.
This patch changes the 'bne 2f' by a 'b 2f'. During init, that
'b 2f' is then replaced by 'bne 2f'
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This replaces almost all of the instruction emulation code in
fix_alignment() with calls to analyse_instr(), emulate_loadstore()
and emulate_dcbz(). The only emulation code left is the SPE
emulation code; analyse_instr() etc. do not handle SPE instructions
at present.
One result of this is that we can now handle alignment faults on
all the new VSX load and store instructions that were added in POWER9.
VSX loads/stores will take alignment faults for unaligned accesses
to cache-inhibited memory.
Another effect is that we no longer rely on the DAR and DSISR values
set by the processor.
With this, we now need to include the instruction emulation code
unconditionally.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Anton noticed that if we fault part way through emulating an unaligned
instruction, we don't update the DAR to reflect that.
The DAR value is eventually reported back to userspace as the address
in the SEGV signal, and if userspace is using that value to demand
fault then it can be confused by us not setting the value correctly.
This patch is ugly as hell, but is intended to be the minimal fix and
back ports easily.
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
In previous generations of Power processors each core had a private L2
cache. The Power 9 processor has a slightly different design where the
L2 cache is shared among pairs of cores rather than being completely
private.
Making the scheduler aware of this cache sharing allows the scheduler to
make better migration decisions. For example, if two CPU heavy tasks
share a core then one task can be migrated to the paired core to improve
throughput. Under the existing three level topology the task could be
migrated to any core on the same chip, while with the new topology it
would be preferentially migrated to the paired core so it remains
cache-hot.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We want to add an extra level to the CPU scheduler topology to account
for cores which share a cache. To do this we need to build a cpumask
for each CPU that indicates which CPUs share this cache to use as an
input to the scheduler.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The CPU scheduler topology is constructed from a number of per-cpu
cpumasks which describe which sets of logical CPUs are related in some
fashion. Current code that handles constructing these masks when CPUs
are hot(un)plugged can be simplified a bit by exploiting the fact that
the scheduler requires higher levels of the toplogy (e.g package level
groupings) to be supersets of the lower levels (e.g. threas in a core).
This patch reworks the cpumask construction to be simpler and easier to
extend with extra topology levels.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
[mpe: Fix CONFIG_HOTPLUG_CPU=n build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When building the CPU scheduler topology the kernel uses the ibm,chipid
property from the devicetree to group logical CPUs. Currently the DT
search for this property is open-coded in smp.c and this functionality
is a duplication of what's in cpu_to_chip_id() already. This patch
removes the existing search in favor of that.
It's worth mentioning that the semantics of the search are different
in cpu_to_chip_id(). When there is no ibm,chipid in the CPUs node it
will also search /cpus and / for the property, but this should not
effect the output topology.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
.llong is an undocumented PPC specific directive. The generic
equivalent is .quad, but even better (because it's self describing) is
.8byte.
Convert all .llong directives to .8byte.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For a PCI device it's pci_dn can be retrieved from
pdev->dev.archdata.firmware_data, PCI_DN(devnode), or parent's list.
Thus, we should just use the existing function pci_get_pdn_by_devfn
to get the pci_dn.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Reviewed-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The check_req() helper uses pci_get_pdn() to get an OF node pointer.
pci_get_pdn() returns a pci_dn pointer which either:
1) from the OF node returned by pci_device_to_OF_node();
2) from the parent child_list where entries don't have OF node pointers.
Since check_req() does not care about 2), it can call
pci_device_to_OF_node() directly, hence the change.
The find_pe_dn() helper uses embedded pci_dn to get an OF node which is
also stored in edev->pdev so let's take a shortcut and call
pci_device_to_OF_node() directly.
With these 2 changes, we can finally get rid of the OF node back pointer.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pci_dn struct caches a OF device node pointer in order to access
the "ibm,loc-code" property when EEH is recovering.
However, when this happens in eeh_dev_check_failure(), we also have
a pci_dev pointer which should have a valid pointer to the device node
when pci_dn has one (both pointers are not NULL for physical functions
and are NULL for virtual functions).
This changes pci_remove_device_node_info() to look for a parent of
the node being removed, just like pci_add_device_node_info() does when it
references the parent node.
This is the first step to get rid of pci_dn::node.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The eeh_dev struct hold a config space address of an associated node
and the very same address is also stored in the pci_dn struct which
is always present during the eeh_dev lifetime.
This uses bus:devfn directly from pci_dn instead of cached and packed
config_addr.
Since config_addr is made from device's bus:dev.fn, there is no point
in keeping it in the debugfs either so remove that too.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The eeh_dev struct already holds a pointer to pci_dn which it does not
exist without and pci_dn itself holds the very same pointer so just
use it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch/powerpc/kernel/eeh_dev.c:57 is the only legit place where edev
is allocated; other 2 places allocate it on stack and in the heap for
a very short period of time to use eeh_pe_get() as takes edev.
This changes eeh_pe_get() to receive required parameters explicitly.
This removes unnecessary temporary allocation of edev.
This uses the "pe_no" name instead of the "pe_config_addr" name as
it actually is a PE number and not a config space address as it seemed.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pdev is always NULL, remove it.
To make checkpatch.pl happy, this also removes the "out of memory"
message.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use nmi_enter similarly to system reset interrupts. This uses NMI
printk NMI buffers and turns off various debugging facilities that
helps avoid tripping on ourselves or other CPUs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are quite a few machine check exceptions that can be caused by
kernel bugs. To make debugging easier, use the kernel crash path in
cases of synchronous machine checks that occur in kernel mode, if that
would not result in the machine going straight to panic or crash dump.
There is a downside here that die()ing the process in kernel mode can
still leave the system unstable. panic_on_oops will always force the
system to fail-stop, so systems where that behaviour is important will
still do the right thing.
As a test, when triggering an i-side 0111b error (ifetch from foreign
address) in kernel mode process context on POWER9, the kernel currently
dies quickly like this:
Severe Machine check interrupt [Not recovered]
NIP [ffff000000000000]: 0xffff000000000000
Initiator: CPU
Error type: Real address [Instruction fetch (foreign)]
[ 127.426651616,0] OPAL: Reboot requested due to Platform error.
Effective[ 127.426693712,3] OPAL: Reboot requested due to Platform error. address: ffff000000000000
opal: Reboot type 1 not supported
Kernel panic - not syncing: PowerNV Unrecovered Machine Check
CPU: 56 PID: 4425 Comm: syscall Tainted: G M 4.12.0-rc1-13857-ga4700a261072-dirty #35
Call Trace:
[ 128.017988928,4] IPMI: BUG: Dropping ESEL on the floor due to
buggy/mising code in OPAL for this BMC
Rebooting in 10 seconds..
Trying to free IRQ 496 from IRQ context!
After this patch, the process is killed and the kernel continues with
this message, which gives enough information to identify the offending
branch (i.e., with CFAR):
Severe Machine check interrupt [Not recovered]
NIP [ffff000000000000]: 0xffff000000000000
Initiator: CPU
Error type: Real address [Instruction fetch (foreign)]
Effective address: ffff000000000000
Oops: Machine check, sig: 7 [#1]
SMP NR_CPUS=2048
NUMA
PowerNV
Modules linked in: iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 ...
CPU: 22 PID: 4436 Comm: syscall Tainted: G M 4.12.0-rc1-13857-ga4700a261072-dirty #36
task: c000000932300000 task.stack: c000000932380000
NIP: ffff000000000000 LR: 00000000217706a4 CTR: ffff000000000000
REGS: c00000000fc8fd80 TRAP: 0200 Tainted: G M (4.12.0-rc1-13857-ga4700a261072-dirty)
MSR: 90000000001c1003 <SF,HV,ME,RI,LE>
CR: 24000484 XER: 20000000
CFAR: c000000000004c80 DAR: 0000000021770a90 DSISR: 0a000000 SOFTE: 1
GPR00: 0000000000001ebe 00007fffce4818b0 0000000021797f00 0000000000000000
GPR04: 00007fff8007ac24 0000000044000484 0000000000004000 00007fff801405e8
GPR08: 900000000280f033 0000000024000484 0000000000000000 0000000000000030
GPR12: 9000000000001003 00007fff801bc370 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR24: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR28: 00007fff801b0000 0000000000000000 00000000217707a0 00007fffce481918
NIP [ffff000000000000] 0xffff000000000000
LR [00000000217706a4] 0x217706a4
Call Trace:
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A system reset is a request to crash / debug the system rather than
necessarily caused by encountering a BUG. So there is no need to
serialize all CPUs behind the die lock, adding taints to all
subsequent traces beyond the first, breaking console locks, etc.
The system reset is NMI context which has its own printk buffers to
prevent output being interleaved. Then it's better to have all
secondaries print out their debug as quickly as possible and the
primary will flush out all printk buffers during panic().
So remove the 0x100 path from die, and move it into system_reset. Name
the crash/dump reasons "System Reset".
This gives "not tained" traces when crashing an untainted kernel. It
also gives the panic reason as "System Reset" as opposed to "Fatal
exception in interrupt" (or "die oops" for fadump).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If fadump is not registered, and no other crash or debug handlers are
registered, the powerpc panic handler stops the guest before the
generic panic code can push out debug information to the console.
Currently, system reset injection causes the guest to silently stop.
Stop calling ppc_md.panic in the panic notifier. crash_fadump already
does rtas_os_term() to terminate the guest if fadump is registered.
Remove ppc_md.panic. Move fadump panic notifier into fadump code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes a couple more bits of fallout from the new hard lockup watchdog
patch.
It restores the required hw_nmi_get_sample_period() function for the
perf watchdog, and removes some function declarations on 64e that are only
defined for 64s. This fixes the 64e build when the hardlockup detector is
enabled.
It restores the default behaviour of disabling the perf watchdog, and also
fixes disabling the 64s watchdog when running as a guest.
Fixes: 2104180a53 ("powerpc/64s: implement arch-specific hardlockup watchdog")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Radix MMU does not take SLB or TLB interrupts when accessing kernel
linear address. Remove this restriction for radix mode.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hardware can execute stop in any context, and KVM does not
require real mode because siblings do not share MMU state. This
saves a switch to real-mode when going idle.
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are no longer any callers of IDLE_STATE_ENTER_SEQ, all callers
use IDLE_STATE_ENTER_SEQ_NORET. So drop the former.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch, write change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We don't need to use IDLE_STATE_ENTER_SEQ_NORET on Power9.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This macro is only used in idle_book3s.S, move it in there and add a
more descriptive comment.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch and write change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 CPUs have independent MMU contexts per thread, so KVM does not
need to quiesce secondary threads, so the hwthread_req/hwthread_state
protocol does not have to be used. So patch it away on POWER9, and patch
away the branch from the Linux idle wakeup to kvm_start_guest that is
never used.
Add a warning and error out of kvmppc_grab_hwthread in case it is ever
called on POWER9.
This avoids a hwsync in the idle wakeup path on POWER9.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
[mpe: Use WARN(...) instead of WARN_ON()/pr_err(...)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch updates the machine check handler of Linux kernel to
handle the e6500 architecture case. In e6500 core, L1 Data Cache Write
Shadow Mode (DCWS) register is not implemented but L1 data cache always
runs in write shadow mode. So, on L1 data cache parity errors, hardware
will automatically invalidate the data cache but will still log a
machine check interrupt.
Signed-off-by: Ronak Desai <ronak.desai@rockwellcollins.com>
Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Somehow we missed this when the pr_cont() changes went in. Fix CR/XER
to go on the same line as MSR, as they have historically, eg:
MSR: 8000000000009032 <SF,EE,ME,IR,DR,RI> CR: 4804408a XER: 20000000
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Although the MSR tells you what endian you're in it's possible that
isn't the same endian the kernel was built for, and if that happens
you're usually having a very bad day. So print a marker to make
it 100% clear which endian the kernel was built for.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we oops we print a few markers for significant config options
such as PREEMPT, SMP etc. Currently these appear on separate lines
because we're not using pr_cont() properly. Fix it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This helper is used to detect if a uprobe'd function has returned
through a setjmp/longjmp, rather than branching to the LR that was
updated previously by us. This fixes a SIGSEGV that gets generated when
programs use setjmp/longjmp with uretprobes.
We use the arm64 model (arch/arm64/kernel/probes/uprobes.c:
arch_uretprobe_is_alive()) for detecting when stack frames have been
removed from under us.
Reference:
https://marc.info/?l=linux-kernel&m=143748610330073
commit 7b868e4802 ("uprobes/x86: Reimplement arch_uretprobe_is_alive()")
commit db087ef69a ("uprobes/x86: Make arch_uretprobe_is_alive(RP_CHECK_CALL) more
clever")
Tested with the test program from:
https://sourceware.org/git/gitweb.cgi?p=systemtap.git;a=blob;f=testsuite/systemtap.base/bz5274.c;hb=HEAD
And this script:
$ cat test.sh
#!/bin/bash
perf probe -x ./bz5274 -a bz5274_main_return=main%return
perf probe -x ./bz5274 -a bz5274_funca_return=funca%return
perf probe -x ./bz5274 -a bz5274_funcb_return=funcb%return
perf probe -x ./bz5274 -a bz5274_funcc_return=funcc%return
perf probe -x ./bz5274 -a bz5274_funcd_return=funcd%return
perf record -e 'probe_bz5274:*' -aR ./bz5274
Reported-by: Gustavo Luiz Duarte <gduarte@redhat.com>
Reported-by: zsun@redhat.com
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We don't save/restore these across a trap, or with KPROBES_ON_FTRACE.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On modern CPUs the CTRL register is read-only except bit 63 which is
the run latch control. This means it can be updated with a mtspr
rather than mfspr/mtspr.
To accomodate older CPUs (Cell at least), where there are other bits
in the register, we still do a read/modify/write on pre 2.06 CPUs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Update change log to mention 2.06 workaround]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
HVI interrupts have always used 0x500, so remove the dead branch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 host external interrupts use the h_virt_irq_common handler, so
use that to replay them rather than using the hardware_interrupt_common
handler. Both call do_IRQ, but using the correct handler reduces
i-cache footprint.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This results in smaller code, and fewer branches. This relies on the
fact that both the 0xe80 and 0xa00 handlers call the same upper level
code, namely doorbell_exception().
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Mention we rely on the implementation of the 0xe80/0xa00 handlers]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the clearing of irq_happened bits into the condition where they
were found to be set. This reduces instruction count slightly, and
reduces stores into irq_happened.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Places in the kernel where r13 is not the PACA pointer must have
maskable interrupts disabled, so r13 does not have to be restored when
returning from a soft-masked interrupt. We should never have
interrupts soft disabled when we're in user space.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
MSR_EE is always enabled in SRR1 for masked interrupts, so we can use
xor to clear it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Interrupts which do not require EE to be cleared can all be tested
with a single bitwise test.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In __replay_interrupt() we take the address of a local label so we can
return to it later. However the assembler turns the local label into a
symbol with a name like ".L1^B42" - where "^B" is literally "\002".
This does not make for pleasant stack traces. Fix it by giving the
label a sensible name.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linuxppc-dev@lists.ozlabs.org
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There's a non-trivial dependency between some commits we want to put in
next and the KVM prefetch work around that went into fixes. So merge
fixes into next.
Bring in the commit to rename find_linux_pte_or_hugepte() which touches
arch and KVM code, and might need to be merged with the kvmppc tree to
avoid conflicts.
Add newer helpers to make the function usage simpler. It is always
recommended to use find_current_mm_pte() for walking the page table.
If we cannot use find_current_mm_pte(), it should be documented why
the said usage of __find_linux_pte() is safe against a parallel THP
split.
For now we have KVM code using __find_linux_pte(). This is because kvm
code ends up calling __find_linux_pte() in real mode with MSR_EE=0 but
with PACA soft_enabled = 1. We may want to fix that later and make
sure we keep the MSR_EE and PACA soft_enabled in sync. When we do that
we can switch kvm to use find_linux_pte().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__giveup_vsx/save_vsx are completely equivalent to testing MSR_FP
and MSR_VEC and calling the corresponding giveup/save function so
just remove the spurious VSX cases. Also add WARN_ONs checking that
we never have VSX enabled without the two other.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__giveup_fpu() already does it and we cannot have MSR_VSX set
without having MSR_FP also set.
This also adds a warning to check we indeed do
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__giveup_vsx() already calls those two functions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
VSX uses a combination of the old vector registers, the old FP
registers and new "second halves" of the FP registers.
Thus when we need to see the VSX state in the thread struct
(flush_vsx_to_thread()) or when we'll use the VSX in the kernel
(enable_kernel_vsx()) we need to ensure they are all flushed into
the thread struct if either of them is individually enabled.
Unfortunately we only tested if the whole VSX was enabled, not if they
were individually enabled.
Fixes: 72cd7b44bc ("powerpc: Uncomment and make enable_kernel_vsx() routine available")
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With commit aa888a7497 ("hugetlb: support larger than MAX_ORDER") we added
support for allocating gigantic hugepages via kernel command line. Switch
ppc64 arch specific code to use that.
W.r.t FSL support, we now limit our allocation range using BOOTMEM_ALLOC_ACCESSIBLE.
We use the kernel command line to do reservation of hugetlb pages on powernv
platforms. On pseries hash mmu mode the supported gigantic huge page size is
16GB and that can only be allocated with hypervisor assist. For pseries the
command line option doesn't do the allocation. Instead pseries does gigantic
hugepage allocation based on hypervisor hint that is specified via
"ibm,expected#pages" property of the memory node.
Cc: Scott Wood <oss@buserror.net>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch implements STRICT_KERNEL_RWX on PPC32.
As for CONFIG_DEBUG_PAGEALLOC, it deactivates BAT and LTLB mappings
in order to allow page protection setup at the level of each page.
As BAT/LTLB mappings are deactivated, there might be a performance
impact.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reduces the DTLB miss handler hot path (user address path)
by one instruction by preserving r10.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As stated in a comment in head_8xx.S, today we "Always pin the first
8 MB ITLB to prevent ITLB misses while mucking around with SRR0/SRR1
in asm".
This issue has just been cleared by the preceding patch, therefore
we can make this pinning optional (on by default) and independent
of DATA pinning.
This patch also makes pinning of IMMR independent of pinning of DATA.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
By default, the 8xx pins an ITLB on the first 8M of memory in order
to avoid any ITLB miss on kernel code.
However, with some debug functions like DEBUG_PAGEALLOC and
DEBUG_RODATA, pinning TLBs is contradictory.
In order to avoid any ITLB miss in a critical section without pinning
TLBs, we have to ensure that there is no page boundary crossed between
the setup of a new value in SRR0/SRR1 and the associated RFI.
The functions modifying srr0/srr1 are all located in setup_32.S.
They are spread over almost 4kbytes.
The patch forces a 12 bits (4kbytes) alignment for those
functions. This garanties that the functions remain in a
single 4k page.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The macro to check if an address is a kernel address or not is
not used anymore in DTLBmiss handler. It is used in ITLB miss handler
and in DTLB error handler. DTLB error handler is not a hot path, it
doesn't need such optimisation.
In order to simplify a following patch which will rework ITLB miss
handler, we remove the macros and reintroduce them inside the handler.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes another invalid use of register expressions.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In iommu_range_alloc() we generate a mask by right shifting ~0,
however if the specified alignment is 0 then we right shift by 64,
which is undefined. UBSAN tells us so:
UBSAN: Undefined behaviour in ../arch/powerpc/kernel/iommu.c:193:35
shift exponent 64 is too large for 64-bit type 'long unsigned int'
We can avoid it by instead generating the mask with:
align_mask = (1ull << align_order) - 1;
That will also generate an undefined shift if align_order is 64 or
greater, but that shouldn't be a problem for a while.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
head_8xx is dedicated to 8xx so no need to use macros that
depends on the CPU
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use symbolic names for DSISR bits in DSI
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For the 8xx, PVR values defined in arch/powerpc/include/asm/reg.h
are nowhere used.
Remove all defines and add PVR_8xx
Use it in arch/powerpc/kernel/cputable.c
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
arch/powerpc is now the only place with remaining use of
CONFIG_8xx: get rid of them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 8xx cannot access the TBL and TBU registers using mfspr/mtspr
It must be accessed using mftb/mftbu
Due to this, there is a number of places with #ifdef CONFIG_8xx
This patch defines new macros MFTBL(x) and MFTBU(x) on the same model
as MFTB(x) and tries to make use of them as much as possible.
In arch/powerpc/include/asm/timex.h, we also remove the ifdef
for the asm() operands as the compiler doesn't mind unused operands
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since commit aa42c69c67 ("[POWERPC] Add support for FP emulation
for the e300c2 core"), program_check_exception() can be called for
math emulation. In that case, 'reason' is 0.
On the 8xx, there is a Software Emulation interrupt which is
called for all unimplemented and illegal instructions. This
interrupt calls SoftwareEmulation() which does almost the
same as program_check_exception() called with reason = 0.
The Software Emulation interrupt sets all reason bits to 0,
it is therefore possible to call program_check_exception()
directly from the interrupt handler.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the same spirit as what was done for 4xx and 44x, move
the 8xx machine check into platforms/8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we open code the reason codes for program checks. Instead use
the existing SRR1 defines.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We already have mce.c which is built for 64bit and contains other parts
of the machine check code, so move these bits in there too.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make it clear that the fallback version of machine_check_generic() is
only used on 32-bit configs.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
get_mc_reason() no longer provides (if it ever really did) any
meaningful abstraction, so remove it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we have 4xx platform directory we can move the 4xx machine
check handler in there. Again we drop get_mc_reason() and replace it
with regs->dsisr directly (which is actually SPRN_ESR).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have several 44x machine check handlers defined in traps.c. It would
be preferable if they were split out with the platforms that use them.
Do that.
In the process, drop get_mc_reason() and instead just open code the
lookup of reason from regs->dsisr. This avoids a pointless layer of
abstraction.
We know to use regs->dsisr because 44x enables BOOKE which enables
PPC_ADV_DEBUG_REGS, and FSL_BOOKE is not enabled on 44x builds.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we build the 47x cputable entries even when CONFIG_PPC_47x is
disabled. That means a kernel built without CONFIG_PPC_47x will claim to
support a 47x CPU and start booting, only to break somewhere later
because it doesn't have 47x support compiled in.
So guard the 47x cputable entries with CONFIG_PPC_47x. Note that this is
inside the #ifdef CONFIG_44x section, because 47x depends on 44x.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds an irq counter for the watchdog soft-NMI. This interrupt
only fires when interrupts are soft-disabled, so it will not
increment much even when the watchdog is running. However it's
useful for debugging and sanity checking.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The powerpc kernel/watchdog.o should be built when HARDLOCKUP_DETECTOR
and HAVE_HARDLOCKUP_DETECTOR_ARCH are both selected. If only the former
is selected, then the generic perf watchdog has been selected.
To simplify this check, introduce a new Kconfig symbol PPC_WATCHDOG that
depends on both. This Kconfig option means the powerpc specific
watchdog is enabled.
Without this patch, Book3E will attempt to build the powerpc watchdog.
Fixes: 2104180a53 ("powerpc/64s: implement arch-specific hardlockup watchdog")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On 64-bit Book3s, when we're in HV mode, we have already counted the
machine check exception in machine_check_early().
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Use IS_ENABLED() rather than an #ifdef]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
binutils >= 2.26 now warns about misuse of register expressions in
assembler operands that are actually literals, for example:
arch/powerpc/kernel/entry_64.S:535: Warning: invalid register expression
In practice these are almost all uses of r0 that should just be a
literal 0.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
[mpe: Mention r0 is almost always the culprit, fold in purgatory change]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When CPUs start and stop the watchdog, they manipulate shared data
that is normally protected by the lock. Other CPUs can be running
concurrently at this time, so it's a good idea to use locking here
to be on the safe side.
Remove the barrier which is undocumented and didn't do anything.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the SMP detector finds other CPUs stuck, it iterates over
them and marks them as stuck. This pulls them out of the pending
mask and allows the detector to continue with remaining good
CPUs (if nmi_watchdog=panic is not enabled).
The code to dothat was buggy because when setting a CPU stuck,
if the pending mask became empty, it resets it to keep the
watchdog running. However the iterator will continue to run
over the new pending mask and mark remaining good CPUs sas stuck.
Fix this by doing it with cpumask bitwise operations.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the watchdog decides to panic, it takes the lock and double
checks everything (to avoid races with the CPU being unstuck or
panic()ed by something else).
The exit label was misplaced and would result in all-CPUs backtrace
and watchdog panic even in the case that the condition was found to be
resolved.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some code can go into a tight loop calling touch_nmi_watchdog (e.g.,
stop_machine CPU hotplug code). This can cause contention on watchdog
locks particularly if all CPUs with watchdog enabled are spinning in
the loops.
Avoid this storm of activity by running the watchdog timer callback
from this path if we have exceeded the timer period since it was last
run.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- Hard-disable interrupts before taking the lock, which prevents
soft-NMI re-entrancy and therefore can prevent deadlocks.
- Use raw_ variants of local_irq_disable to avoid irq debugging.
- When the lock is contended, spin at low SMT priority, using
loads only, and with interrupts enabled (where possible).
Some stalls have been noticed at high loads that go away with improved
locking. There should not be so much locking contention in the first
place (which is addressed in a subsequent patch), but locking should
still be improved.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the NMI IPI lock is contended, spin at low SMT priority, using
loads only, and with interrupts enabled (where possible). This
improves behaviour under high contention (e.g., a system crash when
a number of CPUs are trying to enter the debugger).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d300627c6a ("powerpc/6xx: Handle DABR match before calling
do_page_fault") breaks non 6xx platforms.
Failed to execute /init (error -14)
Starting init: /bin/sh exists but couldn't execute it (error -14)
Kernel panic - not syncing: No working init found. Try passing init= ...
CPU: 0 PID: 1 Comm: init Not tainted 4.13.0-rc3-s3k-dev-00143-g7aa62e972a56 #56
Call Trace:
panic+0x108/0x250 (unreliable)
rootfs_mount+0x0/0x58
ret_from_kernel_thread+0x5c/0x64
Rebooting in 180 seconds..
This is because in handle_page_fault(), the call to do_page_fault() has been
mistakenly enclosed inside an #ifdef CONFIG_6xx
Fixes: d300627c6a ("powerpc/6xx: Handle DABR match before calling do_page_fault")
Brown-paper-bag-to-be-worn-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the decrementer wraps again and de-asserts the decrementer
exception while hard-disabled, __check_irq_replay() has a test to
notice the wrap when interrupts are re-enabled.
The decrementer check must be done when clearing the PACA_IRQ_HARD_DIS
flag, not when the PACA_IRQ_DEC flag is tested. Previously this worked
because the decrementer interrupt was always the first one checked
after clearing the hard disable flag, but HMI check was moved ahead of
that, which introduced this bug.
This can cause a missed decrementer interrupt if we soft-disable
interrupts then take an HMI which is recorded in irq_happened, then
hard-disable interrupts for > 4s to wrap the decrementer.
Fixes: e0e0d6b739 ("powerpc/64: Replay hypervisor maintenance interrupt first")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD2 PMU can stop after a state-loss idle in some conditions.
A solution is to set then clear MMCRA[60] after wake from state-loss
idle. MMCRA[60] is a non-architected bit, see the user manual for
details.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Reviewed-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This uses the newly defined constants for this rather than open-coded
numbers. There is a side effect on 64-bit which is to pass through
some of the new P9 bits which we didn't before.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We test a number of bits from DSISR/SRR1 before deciding
to call hash_page(). If any of these is set, we go directly
to do_page_fault() as the bit indicate a fault that needs
to be handled there (no hashing needed).
This updates the current open-coded masks to use the new
DSISR definitions.
This *does* change the masks actually used in two ways:
- We used to test various bits that were defined as "always 0"
in the architecture and could be repurposed for something
else. From now on, we just ignore such bits.
- We were missing some new bits defined on P9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On legacy 6xx 32-bit procesors, we checked for the DABR match bit
in DSISR from do_page_fault(), in the middle of a pile of ifdef's
because all other CPU types do it in assembly prior to calling
do_page_fault. Fix that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Add #ifdef CONFIG_6xx]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
By filtering the relevant SRR1 bits in the assembly rather than
in do_page_fault() itself, we avoid a conditional branch (since we
already come from different path for data and instruction faults).
This will allow more simplifications later
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace the __this_cpu_read() with raw_cpu_read() in
iommu_range_alloc(). Otherwise we get a warning about using
__this_cpu_read() in preemptible code:
BUG: using __this_cpu_read() in preemptible
caller is iommu_range_alloc+0xa8/0x3d0
Preemption doesn't need to be disabled since according to the comment
any CPU can safely use any IOMMU pool.
Signed-off-by: Victor Aoqui <victora@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The stop4 idle state on POWER9 is a deep idle state which loses
hypervisor resources, but whose latency is low enough that it can be
exposed via cpuidle.
Until now, the deep idle states which lose hypervisor resources (eg:
winkle) were only exposed via CPU-Hotplug. Hence currently on wakeup
from such states, barring a few SPRs which need to be restored to
their older value, rest of the SPRS are reinitialized to their values
corresponding to that at boot time.
When stop4 is used in the context of cpuidle, we want these additional
SPRs to be restored to their older value, to ensure that the context
on the CPU coming back from idle is same as it was before going idle.
In this patch, we define a SPR save area in PACA (since we have used
up the volatile register space in the stack) and on POWER9, we restore
SPRN_PID, SPRN_LDBAR, SPRN_FSCR, SPRN_HFSCR, SPRN_MMCRA, SPRN_MMCR1,
SPRN_MMCR2 to the values they had before entering stop.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The watchdog soft-NMI exception stack setup loads a stack pointer
twice, which is an obvious error. It ends up using the system reset
interrupt (true-NMI) stack, which is also a bug because the watchdog
could be preempted by a system reset interrupt that overwrites the
NMI stack.
Change the soft-NMI to use the "emergency stack". The current kernel
stack is not used, because of the longer-term goal to prevent
asynchronous stack access using soft-disable.
Fixes: 2104180a53 ("powerpc/64s: implement arch-specific hardlockup watchdog")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZapWhAAoJEHm+PkMAQRiGKb0IAJM6b7SbWaw69Og7+qiFB+zZ
xp29iXqbE9fPISC6a5BRQV1ONjeDM6opGixGHqGC8Hla6k2IYz25VDNoF8wd0MXN
cz/Ih20vd3C5afxXGe5cTT8lsPAlV0mWXxForlu6j8jPeL62FPfq6RhEkw7AcrYL
yfYy3k3qSdOrrvBdII0WAAUi46UfIs+we9BQgbsMbkHOiqV2K0MOrzKE84Xbgepq
RAy2xg6P4b4+hTx8xTrYc1MXwpnqjRc0oJ08gdmiwW3AOOU7LxYFn7zDkLPWi9Rr
g4x6r4YhBTGxT4wNvovLIiqd9QFs//dMCuPWYwEtTICG48umIqqq24beQ0mvCdg=
=08Ic
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc1' into fixes
The fixes branch is based off a random pre-rc1 commit, because we had
some fixes that needed to go in before rc1 was released.
However we now need to fix some code that went in after that point, but
before rc1, so merge rc1 to get that code into fixes so we can fix it!
In smp_cpus_done() we need to call smp_ops->setup_cpu() for the boot
CPU, which means it has to run *on* the boot CPU.
In the past we ensured it ran on the boot CPU by changing the CPU
affinity mask of current directly. That was removed in commit
6d11b87d55 ("powerpc/smp: Replace open coded task affinity logic"),
and replaced with a work queue call.
Unfortunately using a work queue leads to a lockdep warning, now that
the CPU hotplug lock is a regular semaphore:
======================================================
WARNING: possible circular locking dependency detected
...
kworker/0:1/971 is trying to acquire lock:
(cpu_hotplug_lock.rw_sem){++++++}, at: [<c000000000100974>] apply_workqueue_attrs+0x34/0xa0
but task is already holding lock:
((&wfc.work)){+.+.+.}, at: [<c0000000000fdb2c>] process_one_work+0x25c/0x800
...
CPU0 CPU1
---- ----
lock((&wfc.work));
lock(cpu_hotplug_lock.rw_sem);
lock((&wfc.work));
lock(cpu_hotplug_lock.rw_sem);
Although the deadlock can't happen in practice, because
smp_cpus_done() only runs in early boot before CPU hotplug is allowed,
lockdep can't tell that.
Luckily in commit 8fb12156b8 ("init: Pin init task to the boot CPU,
initially") tglx changed the generic code to pin init to the boot CPU
to begin with. The unpinning of init from the boot CPU happens in
sched_init_smp(), which is called after smp_cpus_done().
So smp_cpus_done() is always called on the boot CPU, which means we
don't need the work queue call at all - and the lockdep warning goes
away.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Currently flush_tmregs_to_thread() does not save the TM SPRs (TFHAR,
TFIAR, TEXASR) to the thread struct, unless the process is currently
inside a suspended transaction.
If the process is core dumping, and the TM SPRs have changed since the
last time the process was context switched, then we will save stale
values of the TM SPRs to the core dump.
Fix it by saving the live register state to the thread struct in that
case.
Fixes: 08e1c01d6a ("powerpc/ptrace: Enable support for TM SPR state")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
struct siginfo is a union and the kernel since 2.4 has been hiding a union
tag in the high 16bits of si_code using the values:
__SI_KILL
__SI_TIMER
__SI_POLL
__SI_FAULT
__SI_CHLD
__SI_RT
__SI_MESGQ
__SI_SYS
While this looks plausible on the surface, in practice this situation has
not worked well.
- Injected positive signals are not copied to user space properly
unless they have these magic high bits set.
- Injected positive signals are not reported properly by signalfd
unless they have these magic high bits set.
- These kernel internal values leaked to userspace via ptrace_peek_siginfo
- It was possible to inject these kernel internal values and cause the
the kernel to misbehave.
- Kernel developers got confused and expected these kernel internal values
in userspace in kernel self tests.
- Kernel developers got confused and set si_code to __SI_FAULT which
is SI_USER in userspace which causes userspace to think an ordinary user
sent the signal and that it was not kernel generated.
- The values make it impossible to reorganize the code to transform
siginfo_copy_to_user into a plain copy_to_user. As si_code must
be massaged before being passed to userspace.
So remove these kernel internal si codes and make the kernel code simpler
and more maintainable.
To replace these kernel internal magic si_codes introduce the helper
function siginfo_layout, that takes a signal number and an si_code and
computes which union member of siginfo is being used. Have
siginfo_layout return an enumeration so that gcc will have enough
information to warn if a switch statement does not handle all of union
members.
A couple of architectures have a messed up ABI that defines signal
specific duplications of SI_USER which causes more special cases in
siginfo_layout than I would like. The good news is only problem
architectures pay the cost.
Update all of the code that used the previous magic __SI_ values to
use the new SIL_ values and to call siginfo_layout to get those
values. Escept where not all of the cases are handled remove the
defaults in the switch statements so that if a new case is missed in
the future the lack will show up at compile time.
Modify the code that copies siginfo si_code to userspace to just copy
the value and not cast si_code to a short first. The high bits are no
longer used to hold a magic union member.
Fixup the siginfo header files to stop including the __SI_ values in
their constants and for the headers that were missing it to properly
update the number of si_codes for each signal type.
The fixes to copy_siginfo_from_user32 implementations has the
interesting property that several of them perviously should never have
worked as the __SI_ values they depended up where kernel internal.
With that dependency gone those implementations should work much
better.
The idea of not passing the __SI_ values out to userspace and then
not reinserting them has been tested with criu and criu worked without
changes.
Ref: 2.4.0-test1
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
A handful of fixes, mostly for new code.
Some reworking of the new STRICT_KERNEL_RWX support to make sure we also remove
executable permission from __init memory before it's freed.
A fix to some recent optimisations to the hypercall entry where we were
clobbering r12, this was breaking nested guests (PR KVM).
A fix for the recent patch to opal_configure_cores(). This could break booting
on bare metal Power8 boxes if the kernel was built without
CONFIG_JUMP_LABEL_FEATURE_CHECK_DEBUG.
And finally a workaround for spurious PMU interrupts on Power9 DD2.
Thanks to:
Nicholas Piggin, Anton Blanchard, Balbir Singh.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Oy4/
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A handful of fixes, mostly for new code:
- some reworking of the new STRICT_KERNEL_RWX support to make sure we
also remove executable permission from __init memory before it's
freed.
- a fix to some recent optimisations to the hypercall entry where we
were clobbering r12, this was breaking nested guests (PR KVM).
- a fix for the recent patch to opal_configure_cores(). This could
break booting on bare metal Power8 boxes if the kernel was built
without CONFIG_JUMP_LABEL_FEATURE_CHECK_DEBUG.
- .. and finally a workaround for spurious PMU interrupts on Power9
DD2.
Thanks to: Nicholas Piggin, Anton Blanchard, Balbir Singh"
* tag 'powerpc-4.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Mark __init memory no-execute when STRICT_KERNEL_RWX=y
powerpc/mm/hash: Refactor hash__mark_rodata_ro()
powerpc/mm/radix: Refactor radix__mark_rodata_ro()
powerpc/64s: Fix hypercall entry clobbering r12 input
powerpc/perf: Avoid spurious PMU interrupts after idle
powerpc/powernv: Fix boot on Power8 bare metal due to opal_configure_cores()
A previous optimisation incorrectly assumed the PAPR hcall does
not use r12, and clobbers it upon entry. In fact it is used as
an input. This can result in KVM guests crashing (observed with
PR KVM).
Instead of using r12 to save r13, tihs patch saves r13 in ctr.
This is more costly, but not as slow as using the SPRG.
Fixes: acd7d8cef0 ("powerpc/64s: Optimize hypercall/syscall entry")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD2 can see spurious PMU interrupts after state-loss idle in
some conditions.
A solution is to save and reload MMCR0 over state-loss idle.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nothing that really stands out, just a bunch of fixes that have come in in the
last couple of weeks.
None of these are actually fixes for code that is new in 4.13. It's roughly half
older bugs, with fixes going to stable, and half fixes/updates for Power9.
Thanks to:
Aneesh Kumar K.V, Anton Blanchard, Balbir Singh, Benjamin Herrenschmidt,
Madhavan Srinivasan, Michael Neuling, Nicholas Piggin, Oliver O'Halloran.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6eIT
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Nothing that really stands out, just a bunch of fixes that have come
in in the last couple of weeks.
None of these are actually fixes for code that is new in 4.13. It's
roughly half older bugs, with fixes going to stable, and half
fixes/updates for Power9.
Thanks to: Aneesh Kumar K.V, Anton Blanchard, Balbir Singh, Benjamin
Herrenschmidt, Madhavan Srinivasan, Michael Neuling, Nicholas Piggin,
Oliver O'Halloran"
* tag 'powerpc-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64: Fix atomic64_inc_not_zero() to return an int
powerpc: Fix emulation of mfocrf in emulate_step()
powerpc: Fix emulation of mcrf in emulate_step()
powerpc/perf: Add POWER9 alternate PM_RUN_CYC and PM_RUN_INST_CMPL events
powerpc/perf: Fix SDAR_MODE value for continous sampling on Power9
powerpc/asm: Mark cr0 as clobbered in mftb()
powerpc/powernv: Fix local TLB flush for boot and MCE on POWER9
powerpc/mm/radix: Synchronize updates to the process table
powerpc/mm/radix: Properly clear process table entry
powerpc/powernv: Tell OPAL about our MMU mode on POWER9
powerpc/kexec: Fix radix to hash kexec due to IAMR/AMOR
prom_init is a bit special; in theory it should be able to be linked
separately to the kernel. To keep this from getting too complex, the
symbols that prom_init.c uses are checked.
Fortification adds symbols, and it gets quite messy as it includes
things like panic(). So just don't fortify prom_init.c for now.
Link: http://lkml.kernel.org/r/1497903987-21002-6-git-send-email-keescook@chromium.org
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement an arch-speicfic watchdog rather than use the perf-based
hardlockup detector.
The new watchdog takes the soft-NMI directly, rather than going through
perf. Perf interrupts are to be made maskable in future, so that would
prevent the perf detector from working in those regions.
Additionally, implement a SMP based detector where all CPUs watch one
another by pinging a shared cpumask. This is because powerpc Book3S
does not have a true periodic local NMI, but some platforms do implement
a true NMI IPI.
If a CPU is stuck with interrupts hard disabled, the soft-NMI watchdog
does not work, but the SMP watchdog will. Even on platforms without a
true NMI IPI to get a good trace from the stuck CPU, other CPUs will
notice the lockup sufficiently to report it and panic.
[npiggin@gmail.com: honor watchdog disable at boot/hotplug]
Link: http://lkml.kernel.org/r/20170621001346.5bb337c9@roar.ozlabs.ibm.com
[npiggin@gmail.com: fix false positive warning at CPU unplug]
Link: http://lkml.kernel.org/r/20170630080740.20766-1-npiggin@gmail.com
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20170616065715.18390-6-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Tested-by: Babu Moger <babu.moger@oracle.com> [sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split SOFTLOCKUP_DETECTOR from LOCKUP_DETECTOR, and split
HARDLOCKUP_DETECTOR_PERF from HARDLOCKUP_DETECTOR.
LOCKUP_DETECTOR implies the general boot, sysctl, and programming
interfaces for the lockup detectors.
An architecture that wants to use a hard lockup detector must define
HAVE_HARDLOCKUP_DETECTOR_PERF or HAVE_HARDLOCKUP_DETECTOR_ARCH.
Alternatively an arch can define HAVE_NMI_WATCHDOG, which provides the
minimum arch_touch_nmi_watchdog, and it otherwise does its own thing and
does not implement the LOCKUP_DETECTOR interfaces.
sparc is unusual in that it has started to implement some of the
interfaces, but not fully yet. It should probably be converted to a full
HAVE_HARDLOCKUP_DETECTOR_ARCH.
[npiggin@gmail.com: fix]
Link: http://lkml.kernel.org/r/20170617223522.66c0ad88@roar.ozlabs.ibm.com
Link: http://lkml.kernel.org/r/20170616065715.18390-4-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Don Zickus <dzickus@redhat.com>
Reviewed-by: Babu Moger <babu.moger@oracle.com>
Tested-by: Babu Moger <babu.moger@oracle.com> [sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vmcoreinfo_max_size stands for the vmcoreinfo_data, the correct one we
should use is vmcoreinfo_note whose total size is VMCOREINFO_NOTE_SIZE.
Like explained in commit 77019967f0 ("kdump: fix exported size of
vmcoreinfo note"), it should not affect the actual function, but we
better fix it, also this change should be safe and backward compatible.
After this, we can get rid of variable vmcoreinfo_max_size, let's use
the corresponding macros directly, fewer variables means more safety for
vmcoreinfo operation.
[xlpang@redhat.com: fix build warning]
Link: http://lkml.kernel.org/r/1494830606-27736-1-git-send-email-xlpang@redhat.com
Link: http://lkml.kernel.org/r/1493281021-20737-2-git-send-email-xlpang@redhat.com
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Reviewed-by: Dave Young <dyoung@redhat.com>
Cc: Hari Bathini <hbathini@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are two cases outside the normal address space management
where a CPU's local TLB is to be flushed:
1. Host boot; in case something has left stale entries in the
TLB (e.g., kexec).
2. Machine check; to clean corrupted TLB entries.
CPU state restore from deep idle states also flushes the TLB.
However this seems to be a side effect of reusing the boot code to set
CPU state, rather than a requirement itself.
The current flushing has a number of problems with ISA v3.0B:
- The current radix mode of the MMU is not taken into account. tlbiel
is undefined if the R field does not match the current radix mode.
- ISA v3.0B hash must flush the partition and process table caches.
- ISA v3.0B radix must flush partition and process scoped translations,
partition and process table caches, and also the page walk cache.
Add POWER9 cases to handle these, with radix vs hash determined by the
host MMU mode.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch fixes a crash seen while doing a kexec from radix mode to
hash mode. Key 0 is special in hash and used in the RPN by default, we
set the key values to 0 today. In radix mode key 0 is used to control
supervisor<->user access. In hash key 0 is used by default, so the
first instruction after the switch causes a crash on kexec.
Commit 3b10d0095a ("powerpc/mm/radix: Prevent kernel execution of
user space") introduced the setting of IAMR and AMOR values to prevent
execution of user mode instructions from supervisor mode. We need to
clean up these SPR's on kexec.
Fixes: 3b10d0095a ("powerpc/mm/radix: Prevent kernel execution of user space")
Cc: stable@vger.kernel.org # v4.10+
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull perf fixes from Thomas Gleixner:
"A couple of fixes for perf and kprobes:
- Add he missing exclude_kernel attribute for the precise_ip level so
!CAP_SYS_ADMIN users get the proper results.
- Warn instead of failing completely when perf has no unwind support
for a particular architectiure built in.
- Ensure that jprobes are at function entry and not at some random
place"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes: Ensure that jprobe probepoints are at function entry
kprobes: Simplify register_jprobes()
kprobes: Rename [arch_]function_offset_within_entry() to [arch_]kprobe_on_func_entry()
perf unwind: Do not fail due to missing unwind support
perf evsel: Set attr.exclude_kernel when probing max attr.precise_ip
Rename function_offset_within_entry() to scope it to kprobe namespace by
using kprobe_ prefix, and to also simplify it.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Suggested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/3aa6c7e2e4fb6e00f3c24fa306496a66edb558ea.1499443367.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Highlights include:
- Support for STRICT_KERNEL_RWX on 64-bit server CPUs.
- Platform support for FSP2 (476fpe) board
- Enable ZONE_DEVICE on 64-bit server CPUs.
- Generic & powerpc spin loop primitives to optimise busy waiting
- Convert VDSO update function to use new update_vsyscall() interface
- Optimisations to hypercall/syscall/context-switch paths
- Improvements to the CPU idle code on Power8 and Power9.
As well as many other fixes and improvements.
Thanks to:
Akshay Adiga, Andrew Donnellan, Andrew Jeffery, Anshuman Khandual, Anton
Blanchard, Balbir Singh, Benjamin Herrenschmidt, Christophe Leroy, Christophe
Lombard, Colin Ian King, Dan Carpenter, Gautham R. Shenoy, Hari Bathini, Ian
Munsie, Ivan Mikhaylov, Javier Martinez Canillas, Madhavan Srinivasan,
Masahiro Yamada, Matt Brown, Michael Neuling, Michal Suchanek, Murilo
Opsfelder Araujo, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran, Paul
Mackerras, Pavel Machek, Russell Currey, Santosh Sivaraj, Stephen Rothwell,
Thiago Jung Bauermann, Yang Li.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=w8rj
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for STRICT_KERNEL_RWX on 64-bit server CPUs.
- Platform support for FSP2 (476fpe) board
- Enable ZONE_DEVICE on 64-bit server CPUs.
- Generic & powerpc spin loop primitives to optimise busy waiting
- Convert VDSO update function to use new update_vsyscall() interface
- Optimisations to hypercall/syscall/context-switch paths
- Improvements to the CPU idle code on Power8 and Power9.
As well as many other fixes and improvements.
Thanks to: Akshay Adiga, Andrew Donnellan, Andrew Jeffery, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Benjamin Herrenschmidt,
Christophe Leroy, Christophe Lombard, Colin Ian King, Dan Carpenter,
Gautham R. Shenoy, Hari Bathini, Ian Munsie, Ivan Mikhaylov, Javier
Martinez Canillas, Madhavan Srinivasan, Masahiro Yamada, Matt Brown,
Michael Neuling, Michal Suchanek, Murilo Opsfelder Araujo, Naveen N.
Rao, Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pavel Machek,
Russell Currey, Santosh Sivaraj, Stephen Rothwell, Thiago Jung
Bauermann, Yang Li"
* tag 'powerpc-4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (158 commits)
powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs
powerpc/mm/radix: Implement STRICT_RWX/mark_rodata_ro() for Radix
powerpc/mm/hash: Implement mark_rodata_ro() for hash
powerpc/vmlinux.lds: Align __init_begin to 16M
powerpc/lib/code-patching: Use alternate map for patch_instruction()
powerpc/xmon: Add patch_instruction() support for xmon
powerpc/kprobes/optprobes: Use patch_instruction()
powerpc/kprobes: Move kprobes over to patch_instruction()
powerpc/mm/radix: Fix execute permissions for interrupt_vectors
powerpc/pseries: Fix passing of pp0 in updatepp() and updateboltedpp()
powerpc/64s: Blacklist rtas entry/exit from kprobes
powerpc/64s: Blacklist functions invoked on a trap
powerpc/64s: Un-blacklist system_call() from kprobes
powerpc/64s: Move system_call() symbol to just after setting MSR_EE
powerpc/64s: Blacklist system_call() and system_call_common() from kprobes
powerpc/64s: Convert .L__replay_interrupt_return to a local label
powerpc64/elfv1: Only dereference function descriptor for non-text symbols
cxl: Export library to support IBM XSL
powerpc/dts: Use #include "..." to include local DT
powerpc/perf/hv-24x7: Aggregate result elements on POWER9 SMT8
...
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls
to ->mapping_error so that the dma_map_ops instances are
more self contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)
-----BEGIN PGP SIGNATURE-----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=0Fso
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping infrastructure from Christoph Hellwig:
"This is the first pull request for the new dma-mapping subsystem
In this new subsystem we'll try to properly maintain all the generic
code related to dma-mapping, and will further consolidate arch code
into common helpers.
This pull request contains:
- removal of the DMA_ERROR_CODE macro, replacing it with calls to
->mapping_error so that the dma_map_ops instances are more self
contained and can be shared across architectures (me)
- removal of the ->set_dma_mask method, which duplicates the
->dma_capable one in terms of functionality, but requires more
duplicate code.
- various updates for the coherent dma pool and related arm code
(Vladimir)
- various smaller cleanups (me)"
* tag 'dma-mapping-4.13' of git://git.infradead.org/users/hch/dma-mapping: (56 commits)
ARM: dma-mapping: Remove traces of NOMMU code
ARM: NOMMU: Set ARM_DMA_MEM_BUFFERABLE for M-class cpus
ARM: NOMMU: Introduce dma operations for noMMU
drivers: dma-mapping: allow dma_common_mmap() for NOMMU
drivers: dma-coherent: Introduce default DMA pool
drivers: dma-coherent: Account dma_pfn_offset when used with device tree
dma: Take into account dma_pfn_offset
dma-mapping: replace dmam_alloc_noncoherent with dmam_alloc_attrs
dma-mapping: remove dmam_free_noncoherent
crypto: qat - avoid an uninitialized variable warning
au1100fb: remove a bogus dma_free_nonconsistent call
MAINTAINERS: add entry for dma mapping helpers
powerpc: merge __dma_set_mask into dma_set_mask
dma-mapping: remove the set_dma_mask method
powerpc/cell: use the dma_supported method for ops switching
powerpc/cell: clean up fixed mapping dma_ops initialization
tile: remove dma_supported and mapping_error methods
xen-swiotlb: remove xen_swiotlb_set_dma_mask
arm: implement ->dma_supported instead of ->set_dma_mask
mips/loongson64: implement ->dma_supported instead of ->set_dma_mask
...
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements
There is a small conflict in arch/s390 due to an arch-wide field rename.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZW4XTAAoJEL/70l94x66DkhMH/izpk54KI17PtyQ9VYI2sYeZ
BWK6Kl886g3ij4pFi3pECqjDJzWaa3ai+vFfzzpJJ8OkCJT5Rv4LxC5ERltVVmR8
A3T1I/MRktSC0VJLv34daPC2z4Lco/6SPipUpPnL4bE2HATKed4vzoOjQ3tOeGTy
dwi7TFjKwoVDiM7kPPDRnTHqCe5G5n13sZ49dBe9WeJ7ttJauWqoxhlYosCGNPEj
g8ZX8+cvcAhVnz5uFL8roqZ8ygNEQq2mgkU18W8ZZKuiuwR0gdsG0gSBFNTdwIMK
NoreRKMrw0+oLXTIB8SZsoieU6Qi7w3xMAMabe8AJsvYtoersugbOmdxGCr1lsA=
=OD7H
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"PPC:
- Better machine check handling for HV KVM
- Ability to support guests with threads=2, 4 or 8 on POWER9
- Fix for a race that could cause delayed recognition of signals
- Fix for a bug where POWER9 guests could sleep with interrupts pending.
ARM:
- VCPU request overhaul
- allow timer and PMU to have their interrupt number selected from userspace
- workaround for Cavium erratum 30115
- handling of memory poisonning
- the usual crop of fixes and cleanups
s390:
- initial machine check forwarding
- migration support for the CMMA page hinting information
- cleanups and fixes
x86:
- nested VMX bugfixes and improvements
- more reliable NMI window detection on AMD
- APIC timer optimizations
Generic:
- VCPU request overhaul + documentation of common code patterns
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
Update my email address
kvm: vmx: allow host to access guest MSR_IA32_BNDCFGS
x86: kvm: mmu: use ept a/d in vmcs02 iff used in vmcs12
kvm: x86: mmu: allow A/D bits to be disabled in an mmu
x86: kvm: mmu: make spte mmio mask more explicit
x86: kvm: mmu: dead code thanks to access tracking
KVM: PPC: Book3S: Fix typo in XICS-on-XIVE state saving code
KVM: PPC: Book3S HV: Close race with testing for signals on guest entry
KVM: PPC: Book3S HV: Simplify dynamic micro-threading code
KVM: x86: remove ignored type attribute
KVM: LAPIC: Fix lapic timer injection delay
KVM: lapic: reorganize restart_apic_timer
KVM: lapic: reorganize start_hv_timer
kvm: nVMX: Check memory operand to INVVPID
KVM: s390: Inject machine check into the nested guest
KVM: s390: Inject machine check into the guest
tools/kvm_stat: add new interactive command 'b'
tools/kvm_stat: add new command line switch '-i'
tools/kvm_stat: fix error on interactive command 'g'
KVM: SVM: suppress unnecessary NMI singlestep on GIF=0 and nested exit
...
- use memdup_user() instead of open-coded copies (Geliang Tang)
- fix record memory leak during initialization (Douglas Anderson)
- avoid confused compressed record warning (Ankit Kumar)
- prepopulate record timestamp and remove redundant logic from backends
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=VRl5
-----END PGP SIGNATURE-----
Merge tag 'pstore-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"Various fixes and tweaks for the pstore subsystem.
Highlights:
- use memdup_user() instead of open-coded copies (Geliang Tang)
- fix record memory leak during initialization (Douglas Anderson)
- avoid confused compressed record warning (Ankit Kumar)
- prepopulate record timestamp and remove redundant logic from
backends"
* tag 'pstore-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
powerpc/nvram: use memdup_user
pstore: use memdup_user
pstore: Fix format string to use %u for record id
pstore: Populate pstore record->time field
pstore: Create common record initializer
efi-pstore: Refactor erase routine
pstore: Avoid potential infinite loop
pstore: Fix leaked pstore_record in pstore_get_backend_records()
pstore: Don't warn if data is uncompressed and type is not PSTORE_TYPE_DMESG
Pull SMP hotplug updates from Thomas Gleixner:
"This update is primarily a cleanup of the CPU hotplug locking code.
The hotplug locking mechanism is an open coded RWSEM, which allows
recursive locking. The main problem with that is the recursive nature
as it evades the full lockdep coverage and hides potential deadlocks.
The rework replaces the open coded RWSEM with a percpu RWSEM and
establishes full lockdep coverage that way.
The bulk of the changes fix up recursive locking issues and address
the now fully reported potential deadlocks all over the place. Some of
these deadlocks have been observed in the RT tree, but on mainline the
probability was low enough to hide them away."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
cpu/hotplug: Constify attribute_group structures
powerpc: Only obtain cpu_hotplug_lock if called by rtasd
ARM/hw_breakpoint: Fix possible recursive locking for arch_hw_breakpoint_init
cpu/hotplug: Remove unused check_for_tasks() function
perf/core: Don't release cred_guard_mutex if not taken
cpuhotplug: Link lock stacks for hotplug callbacks
acpi/processor: Prevent cpu hotplug deadlock
sched: Provide is_percpu_thread() helper
cpu/hotplug: Convert hotplug locking to percpu rwsem
s390: Prevent hotplug rwsem recursion
arm: Prevent hotplug rwsem recursion
arm64: Prevent cpu hotplug rwsem recursion
kprobes: Cure hotplug lock ordering issues
jump_label: Reorder hotplug lock and jump_label_lock
perf/tracing/cpuhotplug: Fix locking order
ACPI/processor: Use cpu_hotplug_disable() instead of get_online_cpus()
PCI: Replace the racy recursion prevention
PCI: Use cpu_hotplug_disable() instead of get_online_cpus()
perf/x86/intel: Drop get_online_cpus() in intel_snb_check_microcode()
x86/perf: Drop EXPORT of perf_check_microcode
...
For CONFIG_STRICT_KERNEL_RWX align __init_begin to 16M. We use 16M
since its the larger of 2M on radix and 16M on hash for our linear
mapping. The plan is to have .text, .rodata and everything upto
__init_begin marked as RX. Note we still have executable read only
data. We could further align rodata to another 16M boundary. I've used
keeping text plus rodata as read-only-executable as a trade-off to
doing read-only-executable for text and read-only for rodata.
We don't use multi PT_LOAD in PHDRS because we are not sure if all
bootloaders support them. This patch keeps PHDRS in vmlinux.lds.S as
the same they are with just one PT_LOAD for all of the kernel marked
as RWX (7).
mpe: What this means is the added alignment bloats the resulting
binary on disk, a powernv kernel goes from 17M to 22M.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
So that we can implement STRICT_RWX, use patch_instruction() in
optprobes.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch_arm/disarm_probe() use direct assignment for copying
instructions, replace them with patch_instruction(). We don't need to
call flush_icache_range() because patch_instruction() does it for us.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We can't take traps with relocation off, so blacklist enter_rtas() and
rtas_return_loc(). However, instead of blacklisting all of enter_rtas(),
introduce a new symbol __enter_rtas from where on we can't take a trap
and blacklist that.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Blacklist all functions involved while handling a trap. We:
- convert some of the symbols into private symbols, and
- blacklist most functions involved while handling a trap.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is actually safe to probe system_call() in entry_64.S, but only till
we unset MSR_RI. To allow this, add a new symbol system_call_exit()
after the mtmsrd and blacklist that.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It is common to get a PMU interrupt right after the mtmsr instruction that
enables interrupts. Due to this, the stack trace profile gets needlessly split
across system_call_common() and system_call().
Previously, system_call() symbol was at the current place to hide a few
earlier symbols which have since been made private or removed entirely.
So, let's move system_call() slightly higher up, right after the mtmsr
instruction that enables interrupts. Convert existing references to
system_call to a local syscall symbol.
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Convert some of the symbols into private symbols and blacklist
system_call_common() and system_call() from kprobes. We can't take a
trap at parts of these functions as either MSR_RI is unset or the
kernel stack pointer is not yet setup.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Don't convert system_call_common to _GLOBAL()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit b48bbb82e2 ("powerpc/64s: Don't unbalance the return branch
predictor in __replay_interrupt()") introduced __replay_interrupt_return
symbol with '.L' prefix in hopes of keeping it private. However, due to
the use of LOAD_REG_ADDR(), the assembler kept this symbol visible. Fix
the same by instead using the local label '1'.
Fixes: Commit b48bbb82e2 ("powerpc/64s: Don't unbalance the return branch
predictor in __replay_interrupt()")
Suggested-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Merge our fixes branch, a few of them are tripping people up while
working on top of next, and we also have a dependency between the CXL
fixes and new CXL code we want to merge into next.
Use the different spin loop primitives in some simple powerpc
spin loops, including those which will spin as a common case.
This will help to test the spin loop primitives before more
conversions are done.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add some includes of <linux/processor.h>]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
DMA_ERROR_CODE is going to go away, so don't rely on it. Instead
define a ->mapping_error method for all IOMMU based dma operation
instances. The direct ops don't ever return an error and don't
need a ->mapping_error method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
pnv_wakeup_noloss() expects r12 to contain SRR1 value to determine if the wakeup
reason is an HMI in CHECK_HMI_INTERRUPT.
When we wakeup with ESL=0, SRR1 will not contain the wakeup reason, so there is
no point setting r12 to SRR1.
However, we don't set r12 at all so r12 contains garbage (likely a kernel
pointer), and is still used to check HMI assuming that it contained SRR1. This
causes the OPAL msglog to be filled with the following print:
HMI: Received HMI interrupt: HMER = 0x0040000000000000
This patch clears r12 after waking up from stop with ESL=EC=0, so that we don't
accidentally enter the HMI handler in pnv_wakeup_noloss() if the value of
r12[42:45] corresponds to HMI as wakeup reason.
Prior to commit 9d29250136 ("powerpc/64s/idle: Avoid SRR usage in idle
sleep/wake paths") this bug existed, in that we would incorrectly look at SRR1
to check for a HMI when SRR1 didn't contain a wakeup reason. However the SRR1
value would just happen to never have bits 42:45 set.
Fixes: 9d29250136 ("powerpc/64s/idle: Avoid SRR usage in idle sleep/wake paths")
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Change log and comment massaging]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
nr_cpu_ids can be limited by nr_cpus boot parameter, whereas NR_CPUS is a
compile time constant, which shouldn't be compared against during cpu kick.
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During secondary start, we do not need to BUG_ON if an invalid CPU number
is passed. We already print an error if secondary cannot be started, so
just return an error instead.
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Around 95% of memory is reserved by fadump/capture kernel. All this
memory is freed, one page at a time, on writing '1' to the node
/sys/kernel/fadump_release_mem. On systems with large memory, this
can take a long time to complete, leading to soft lockup warning
messages. To avoid this, add reschedule points at regular intervals.
Also, while memblock_reserve() implicitly takes care of holes in the
given memory range while reserving memory, those holes need to be
taken care of while releasing memory as memory is freed one page at
a time. Add support to skip holes while releasing memory.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
fadump fails to register when there are holes in boot memory area.
Provide a helpful error message to the user in such case.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To register fadump, boot memory area - the size of low memory chunk that
is required for a kernel to boot successfully when booted with restricted
memory, is assumed to have no holes. But this memory area is currently
not protected from hot-remove operations. So, fadump could fail to
re-register after a memory hot-remove operation, if memory is removed
from boot memory area. To avoid this, ensure that memory from boot
memory area is not hot-removed when fadump is registered.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Reviewed-by: Mahesh J Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
fadump sets up crash memory ranges to be used for creating PT_LOAD
program headers in elfcore header. Memory chunk RMA_START through
boot memory area size is added as the first memory range because
firmware, at the time of crash, moves this memory chunk to different
location specified during fadump registration making it necessary to
create a separate program header for it with the correct offset.
This memory chunk is skipped while setting up the remaining memory
ranges. But currently, there is possibility that some of this memory
may have duplicate entries like when it is hot-removed and added
again. Ensure that no two memory ranges represent the same memory.
When 5 lmbs are hot-removed and then hot-plugged before registering
fadump, here is how the program headers in /proc/vmcore exported by
fadump look like
without this change:
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
NOTE 0x0000000000010000 0x0000000000000000 0x0000000000000000
0x0000000000001894 0x0000000000001894 0
LOAD 0x0000000000021020 0xc000000000000000 0x0000000000000000
0x0000000040000000 0x0000000040000000 RWE 0
LOAD 0x0000000040031020 0xc000000000000000 0x0000000000000000
0x0000000010000000 0x0000000010000000 RWE 0
LOAD 0x0000000050040000 0xc000000010000000 0x0000000010000000
0x0000000050000000 0x0000000050000000 RWE 0
LOAD 0x00000000a0040000 0xc000000060000000 0x0000000060000000
0x000000019ffe0000 0x000000019ffe0000 RWE 0
and with this change:
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
NOTE 0x0000000000010000 0x0000000000000000 0x0000000000000000
0x0000000000001894 0x0000000000001894 0
LOAD 0x0000000000021020 0xc000000000000000 0x0000000000000000
0x0000000040000000 0x0000000040000000 RWE 0
LOAD 0x0000000040030000 0xc000000040000000 0x0000000040000000
0x0000000020000000 0x0000000020000000 RWE 0
LOAD 0x0000000060030000 0xc000000060000000 0x0000000060000000
0x000000019ffe0000 0x000000019ffe0000 RWE 0
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Reviewed-by: Mahesh J Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use memdup_user() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
On POWER9 the ERAT may be incorrect on wakeup from some stop states
that lose state. This causes random segvs and illegal instructions
when these stop states are enabled.
This patch invalidates the ERAT on wakeup on POWER9 to prevent this
from causing a problem.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Merge comment change with upstream changes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The asm code assumes the FP regs are at the start of fp_state. While
this is true now, it may not always be the case and there is nothing
enforcing it.
This fixes the asm-offsets to point to the actual FP registers inside
the fp_state. Similarly for VMX.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The P9 PVR bits 12-15 don't indicate a revision but instead different
chip configurations. From BookIV we have:
Bits Configuration
0 : Scale out 12 cores
1 : Scale out 24 cores
2 : Scale up 12 cores
3 : Scale up 24 cores
DD1 doesn't use this but DD2 does. Linux will mostly use the "Scale
out 24 core" configuration (ie. SMT4 not SMT8) which results in a PVR
of 0x004e1200. The reported revision in /proc/cpuinfo is hence
reported incorrectly as "18.0".
This patch fixes this to mask off only the relevant bits for the major
revision (ie. bits 8-11) for POWER9.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Calling arch_update_cpu_topology from a CPU hotplug state machine callback
hits a deadlock because the function tries to get a read lock on
cpu_hotplug_lock while the state machine still holds a write lock on it.
Since all callers of arch_update_cpu_topology except rtasd already hold
cpu_hotplug_lock, this patch changes the function to use
stop_machine_cpuslocked and creates a separate function for rtasd which
still tries to obtain the lock.
Michael Bringmann investigated the bug and provided a detailed analysis
of the deadlock on this previous RFC for an alternate solution:
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Cc: Michael Bringmann <mwb@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1497996510-4032-1-git-send-email-bauerman@linux.vnet.ibm.com
Link: https://patchwork.ozlabs.org/patch/771293/
Emergency stacks have their thread_info mostly uninitialised, which in
particular means garbage preempt_count values.
Emergency stack code runs with interrupts disabled entirely, and is
used very rarely, so this has been unnoticed so far. It was found by a
proposed new powerpc watchdog that takes a soft-NMI directly from the
masked_interrupt handler and using the emergency stack. That crashed
at BUG_ON(in_nmi()) in nmi_enter(). preempt_count()s were found to be
garbage.
To fix this, zero the entire THREAD_SIZE allocation, and initialize
the thread_info.
Cc: stable@vger.kernel.org
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Move it all into setup_64.c, use a function not a macro. Fix
crashes on Cell by setting preempt_count to 0 not HARDIRQ_OFFSET]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This converts the powerpc VDSO time update function to use the new
interface introduced in commit 576094b7f0 ("time: Introduce new
GENERIC_TIME_VSYSCALL", 2012-09-11). Where the old interface gave
us the time as of the last update in seconds and whole nanoseconds,
with the new interface we get the nanoseconds part effectively in
a binary fixed-point format with tk->tkr_mono.shift bits to the
right of the binary point.
With the old interface, the fractional nanoseconds got truncated,
meaning that the value returned by the VDSO clock_gettime function
would have about 1ns of jitter in it compared to the value computed
by the generic timekeeping code in the kernel.
The powerpc VDSO time functions (clock_gettime and gettimeofday)
already work in units of 2^-32 seconds, or 0.23283 ns, because that
makes it simple to split the result into seconds and fractional
seconds, and represent the fractional seconds in either microseconds
or nanoseconds. This is good enough accuracy for now, so this patch
avoids changing how the VDSO works or the interface in the VDSO data
page.
This patch converts the powerpc update_vsyscall_old to be called
update_vsyscall and use the new interface. We convert the fractional
second to units of 2^-32 seconds without truncating to whole nanoseconds.
(There is still a conversion to whole nanoseconds for any legacy users
of the vdso_data/systemcfg stamp_xtime field.)
In addition, this improves the accuracy of the computation of tb_to_xs
for those systems with high-frequency timebase clocks (>= 268.5 MHz)
by doing the right shift in two parts, one before the multiplication and
one after, rather than doing the right shift before the multiplication.
(We can't do all of the right shift after the multiplication unless we
use 128-bit arithmetic.)
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since trace_clock is in a different file and already marked with notrace,
enable tracing in time.c by removing it from the disabled list in Makefile.
Also annotate clocksource read functions and sched_clock with notrace.
Testing: Timer and ftrace selftests run with different trace clocks.
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Santosh Sivaraj <santosh@fossix.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As for slb_miss_realmode(), rename slb_allocate_realmode() to avoid
confusion over whether it runs in real or virtual mode - it runs in
both.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
slb_miss_realmode() doesn't always runs in real mode, which is what the
name implies. So rename it to avoid confusing people.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
All the callers of slb_miss_realmode currently open code the #ifndef
CONFIG_RELOCATABLE check and the branch via CTR in the RELOCATABLE case.
We have a macro to do this, BRANCH_TO_COMMON(), so use it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
It will be used in arch/powerpc/kvm/book3s_hv.c KVM module.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This introduces a new KVM capability to control how KVM behaves
on machine check exception (MCE) in HV KVM guests.
If this capability has not been enabled, KVM redirects machine check
exceptions to guest's 0x200 vector, if the address in error belongs to
the guest. With this capability enabled, KVM will cause a guest exit
with the exit reason indicating an NMI.
The new capability is required to avoid problems if a new kernel/KVM
is used with an old QEMU, running a guest that doesn't issue
"ibm,nmi-register". As old QEMU does not understand the NMI exit
type, it treats it as a fatal error. However, the guest could have
handled the machine check error if the exception was delivered to
guest's 0x200 interrupt vector instead of NMI exit in case of old
QEMU.
[paulus@ozlabs.org - Reworded the commit message to be clearer,
enable only on HV KVM.]
Signed-off-by: Aravinda Prasad <aravinda@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The SLB miss handler uses r3 for the faulting address but r12 is
mostly able to be freed up to save r3 in. It just requires SRR1
be reloaded again on error.
It would be more conventional to use r12 for SRR1 (and use r11 to
save r3), but slb_allocate_realmode clobbers r11 and not r12.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The EXCEPTION_PROLOG_1 used by SLB miss already saves CTR when the
kernel is built with CONFIG_RELOCATABLE. So it does not have to be
saved and reloaded when branching to slb_miss_realmode. It can be
restored from the PACA as usual.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The EX_DAR save area is only used in exceptional cases. With r3 no
longer clobbered by slb_allocate_realmode, saving faulting address to
EX_DAR can be deferred to those cases.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Conflicts:
kernel/sched/Makefile
Pick up the waitqueue related renames - it didn't get much feedback,
so it appears to be uncontroversial. Famous last words? ;-)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In a busy system, idle wakeups can be expected from IPIs and device
interrupts.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Idle code now always runs at the 0xc... effective address whether
in real or virtual mode. This means rfid can be ditched, along
with a lot of SRR manipulations.
In the wakeup path, carry SRR1 around in r12. Use mtmsrd to change
MSR states as required.
This also balances the return prediction for the idle call, by
doing blr rather than rfid to return to the idle caller.
On POWER9, 2-process context switch on different cores, with snooze
disabled, increases performance by 2%.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Incorporate v2 fixes from Nick]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Have the system reset idle wakeup handlers branched to in real mode
with the 0xc... kernel address applied. This allows simplifications of
avoiding rfid when switching to virtual mode in the wakeup handler.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The __replay_interrupt() code is branched to with bl, but the caller is
returned to directly with rfid from the interrupt.
Instead, rfid to a stub that returns to the caller with blr, which
should keep the return branch predictor balanced.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
msgsnd doorbell exceptions are cleared when the doorbell interrupt is
taken. However if a doorbell exception causes a system reset interrupt
wake from power saving state, the message is not cleared. Processing
the doorbell from the system reset interrupt requires msgclr to avoid
taking the exception again.
Testing this plus the previous wakup direct patch gives:
original wakeup direct msgclr
Different threads, same core: 315k/s 264k/s 345k/s
Different cores: 235k/s 242k/s 242k/s
Net speedup is +10% for same core, and +3% for different core.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the CPU wakes from low power state, it begins at the system reset
interrupt with the exception that caused the wakeup encoded in SRR1.
Today, powernv idle wakeup ignores the wakeup reason (except a special
case for HMI), and the regular interrupt corresponding to the
exception will fire after the idle wakeup exits.
Change this to replay the interrupt from the idle wakeup before
interrupts are hard-enabled.
Test on POWER8 of context_switch selftests benchmark with polling idle
disabled (e.g., always nap, giving cross-CPU IPIs) gives the following
results:
original wakeup direct
Different threads, same core: 315k/s 264k/s
Different cores: 235k/s 242k/s
There is a slowdown for doorbell IPI (same core) case because system
reset wakeup does not clear the message and the doorbell interrupt
fires again needlessly.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This simplifies the asm and fixes irq-off tracing over sleep
instructions.
Also move powersave_nap check for POWER8 into C code, and move
PSSCR register value calculation for POWER9 into C.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9, we no longer have the restriction that we had on POWER8
where all threads in a core have to be in the same partition, so
the CPU threads are now independent. However, we still want to be
able to run guests with a virtual SMT topology, if only to allow
migration of guests from POWER8 systems to POWER9.
A guest that has a virtual SMT mode greater than 1 will expect to
be able to use the doorbell facility; it will expect the msgsndp
and msgclrp instructions to work appropriately and to be able to read
sensible values from the TIR (thread identification register) and
DPDES (directed privileged doorbell exception status) special-purpose
registers. However, since each CPU thread is a separate sub-processor
in POWER9, these instructions and registers can only be used within
a single CPU thread.
In order for these instructions to appear to act correctly according
to the guest's virtual SMT mode, we have to trap and emulate them.
We cause them to trap by clearing the HFSCR_MSGP bit in the HFSCR
register. The emulation is triggered by the hypervisor facility
unavailable interrupt that occurs when the guest uses them.
To cause a doorbell interrupt to occur within the guest, we set the
DPDES register to 1. If the guest has interrupts enabled, the CPU
will generate a doorbell interrupt and clear the DPDES register in
hardware. The DPDES hardware register for the guest is saved in the
vcpu->arch.vcore->dpdes field. Since this gets written by the guest
exit code, other VCPUs wishing to cause a doorbell interrupt don't
write that field directly, but instead set a vcpu->arch.doorbell_request
flag. This is consumed and set to 0 by the guest entry code, which
then sets DPDES to 1.
Emulating reads of the DPDES register is somewhat involved, because
it requires reading the doorbell pending interrupt status of all of the
VCPU threads in the virtual core, and if any of those VCPUs are
running, their doorbell status is only up-to-date in the hardware
DPDES registers of the CPUs where they are running. In order to get
a reasonable approximation of the current doorbell status, we send
those CPUs an IPI, causing an exit from the guest which will update
the vcpu->arch.vcore->dpdes field. We then use that value in
constructing the emulated DPDES register value.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to allow us to use a different value for the HFSCR
(Hypervisor Facilities Status and Control Register) when running the
guest from that which applies in the host. The reason for doing this
is to allow us to trap the msgsndp instruction and related operations
in future so that they can be virtualized. We also save the value of
HFSCR when a hypervisor facility unavailable interrupt occurs, because
the high byte of HFSCR indicates which facility the guest attempted to
access.
We save and restore the host value on guest entry/exit because some
bits of it affect host userspace execution.
We only do all this on POWER9, not on POWER8, because we are not
intending to virtualize any of the facilities controlled by HFSCR on
POWER8. In particular, the HFSCR bit that controls execution of
msgsndp and related operations does not exist on POWER8. The HFSCR
doesn't exist at all on POWER7.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On Power9, trying to use data breakpoints throws the splat shown
below. This is because the check for a data breakpoint in DSISR is in
do_hash_page(), which is not called when in Radix mode.
Unable to handle kernel paging request for data at address 0xc000000000e19218
Faulting instruction address: 0xc0000000001155e8
cpu 0x0: Vector: 300 (Data Access) at [c0000000ef1e7b20]
pc: c0000000001155e8: find_pid_ns+0x48/0xe0
lr: c000000000116ac4: find_task_by_vpid+0x44/0x90
sp: c0000000ef1e7da0
msr: 9000000000009033
dar: c000000000e19218
dsisr: 400000
Move the check to handle_page_fault() so as to catch data breakpoints
in both Hash and Radix MMU modes.
We have to change the check in do_hash_page() against 0xa410 to use
0xa450, so as to include the value of (DSISR_DABRMATCH << 16).
There are two sites that call handle_page_fault() when in Radix, both
already pass DSISR in r4.
Fixes: caca285e5a ("powerpc/mm/radix: Use STD_MMU_64 to properly isolate hash related code")
Cc: stable@vger.kernel.org # v4.7+
Reported-by: Shriya R. Kulkarni <shriykul@in.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Fix the fall-through case on hash, we need to reload DSISR]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ftrace_caller() depends on a modified regs->nip to detect if a certain
function has been livepatched. However, with KPROBES_ON_FTRACE, it is
possible for regs->nip to have been modified by the kprobes pre_handler
(jprobes, for instance). In this case, we do not want to invoke the
livepatch_handler so as not to consume the livepatch stack.
To distinguish between the two (kprobes and livepatch), we check if
there is an active kprobe on the current function. If there is, then we
know for sure that it must have modified the NIP as we don't support
livepatching a kprobe'd function. In this case, we simply skip the
livepatch_handler and branch to the new NIP. Otherwise, the
livepatch_handler is invoked.
Fixes: ead514d5fb ("powerpc/kprobes: Add support for KPROBES_ON_FTRACE")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For DYNAMIC_FTRACE_WITH_REGS, we should be passing-in the original set
of registers in pt_regs, to capture the state _before_ ftrace_caller.
However, we are instead passing the stack pointer *after* allocating a
stack frame in ftrace_caller. Fix this by saving the proper value of r1
in pt_regs. Also, use SAVE_10GPRS() to simplify the code.
Fixes: 153086644f ("powerpc/ftrace: Add support for -mprofile-kernel ftrace ABI")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This fixes a crash when function_graph and jprobes are used together.
This is essentially commit 237d28db03 ("ftrace/jprobes/x86: Fix
conflict between jprobes and function graph tracing"), but for powerpc.
Jprobes breaks function_graph tracing since the jprobe hook needs to use
jprobe_return(), which never returns back to the hook, but instead to
the original jprobe'd function. The solution is to momentarily pause
function_graph tracing before invoking the jprobe hook and re-enable it
when returning back to the original jprobe'd function.
Fixes: 6794c78243 ("powerpc64: port of the function graph tracer")
Cc: stable@vger.kernel.org # v2.6.30+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ISA v3.0B copy-paste facility only requires cpabort when switching
to a process that has foreign real addresses mapped (direct access to
accelerators), to clear a potential copy buffer filled by a previous
thread. There is no accelerator driver implemented yet, so cpabort can
be removed. It can be be re-added when a driver is implemented.
POWER9 DD1 requires the copy buffer to always be cleared on context
switch, but if accelerators are not in use, then an unpaired copy from
a dummy region is sufficient to clear data out of the copy buffer.
This increases context switch performance by about 5% on POWER9.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The sync (aka. hwsync, aka. heavyweight sync) in the context switch
code to prevent MMIO access being reordered from the point of view of
a single process if it gets migrated to a different CPU is not
required because there is an hwsync performed earlier in the context
switch path.
Comment this so it's clear enough if anything changes on the scheduler
or the powerpc sides. Remove the hwsync from _switch.
This improves context switch performance by 2-3% on POWER8.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is no need to explicitly break the reservation in _switch,
because we are guaranteed that the context switch path will include a
larx/stcx.
Comment the guarantee and remove the reservation clear from _switch.
This is worth 1-2% in context switch performance.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 4387e9ff25 ("[POWERPC] Fix PMU + soft interrupt disable bug")
hard disabled interrupts over the low level context switch, because
the SLB management can't cope with a PMU interrupt accesing the stack
in that window.
Radix based kernel mapping does not use the SLB so it does not require
interrupts hard disabled here.
This is worth 1-2% in context switch performance on POWER9.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The syscall exit code that branches to restore_math is quite heavy on
Book3S, consisting of 2 mtmsr instructions. Threads that don't use both
FP and vector can get caught here if the kernel ever uses FP or vector.
Lazy-FP/vec context switching also trips this case.
So check for lazy FP and vector before switching RI for restore_math.
Move most of this case out of line.
For threads that do want to restore math registers, the MSR switches are
still suboptimal. Future direction may be to use a soft-RI bit to avoid
MSR switches in kernel (similar to soft-EE), but for now at least the
no-restore
POWER9 context switch rate increases by about 5% due to sched_yield(2)
return performance. I haven't constructed a test to measure the syscall
cost.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
After bc3551257a ("powerpc/64: Allow for relocation-on interrupts from
guest to host"), a getppid() system call goes from 307 cycles to 358
cycles (+17%) on POWER8. This is due significantly to the scratch SPR
used by the hypercall check.
It turns out there are a some volatile registers common to both system
call and hypercall (in particular, r12, cr0, ctr), which can be used to
avoid the SPR and some other overheads. This brings getppid to 320 cycles
(+4%).
Testing hcall entry performance by running "sc 1" in guest userspace
before this patch is 854 cycles, afterwards is 826. Also a small win
there.
POWER9 syscall is improved by about the same amount, hcall not tested.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Supporting 512TB requires us to do a order 3 allocation for level 1 page
table (pgd). This results in page allocation failures with certain workloads.
For now limit 4k linux page size config to 64TB.
Fixes: f6eedbba7a ("powerpc/mm/hash: Increase VA range to 128TB")
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit 8c27226119 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"), we
switched to the generic implementation of cpu_to_node(), which uses a percpu
variable to hold the NUMA node for each CPU.
Unfortunately we neglected to notice that we use cpu_to_node() in the allocation
of our percpu areas, leading to a chicken and egg problem. In practice what
happens is when we are setting up the percpu areas, cpu_to_node() reports that
all CPUs are on node 0, so we allocate all percpu areas on node 0.
This is visible in the dmesg output, as all pcpu allocs being in group 0:
pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07
pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15
pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23
pcpu-alloc: [0] 24 25 26 27 [0] 28 29 30 31
pcpu-alloc: [0] 32 33 34 35 [0] 36 37 38 39
pcpu-alloc: [0] 40 41 42 43 [0] 44 45 46 47
To fix it we need an early_cpu_to_node() which can run prior to percpu being
setup. We already have the numa_cpu_lookup_table we can use, so just plumb it
in. With the patch dmesg output shows two groups, 0 and 1:
pcpu-alloc: [0] 00 01 02 03 [0] 04 05 06 07
pcpu-alloc: [0] 08 09 10 11 [0] 12 13 14 15
pcpu-alloc: [0] 16 17 18 19 [0] 20 21 22 23
pcpu-alloc: [1] 24 25 26 27 [1] 28 29 30 31
pcpu-alloc: [1] 32 33 34 35 [1] 36 37 38 39
pcpu-alloc: [1] 40 41 42 43 [1] 44 45 46 47
We can also check the data_offset in the paca of various CPUs, with the fix we
see:
CPU 0: data_offset = 0x0ffe8b0000
CPU 24: data_offset = 0x1ffe5b0000
And we can see from dmesg that CPU 24 has an allocation on node 1:
node 0: [mem 0x0000000000000000-0x0000000fffffffff]
node 1: [mem 0x0000001000000000-0x0000001fffffffff]
Cc: stable@vger.kernel.org # v3.16+
Fixes: 8c27226119 ("powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The i-side 0111b machine check, which is "Instruction Fetch to foreign
address space", was missed by 7b9f71f974 ("powerpc/64s: POWER9 machine
check handler").
The POWER9 processor core considers host real addresses with a
nonzero value in RA(8:12) as foreign address space, accessible only
by the copy and paste instructions. The copy and paste instruction
pair can be used to invoke the Nest accelerators via the Virtual
Accelerator Switchboard (VAS).
It is an error for any regular load/store or ifetch to go to a foreign
addresses. When relocation is on, this causes an MMU exception. When
relocation is off, a machine check exception. It is possible to trigger
this machine check by branching to a foreign address with MSR[IR]=0.
Fixes: 7b9f71f974 ("powerpc/64s: POWER9 machine check handler")
Reported-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently tsk->thread.load_tm is not initialized in the task creation
and can contain garbage on a new task.
This is an undesired behaviour, since it affects the timing to enable
and disable the transactional memory laziness (disabling and enabling
the MSR TM bit, which affects TM reclaim and recheckpoint in the
scheduling process).
Fixes: 5d176f751e ("powerpc: tm: Enable transactional memory (TM) lazily for userspace")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently tsk->thread->load_vec and load_fp are not initialized during
task creation, which can lead to garbage values in these variables (non-zero
values).
These variables will be checked later in restore_math() to validate if the
FP and vector registers are being utilized. Since these values might be
non-zero, the restore_math() will continue to save the FP and vectors even if
they were never utilized by the userspace application. load_fp and load_vec
counters will then overflow (they wrap at 255) and the FP and Altivec will be
finally disabled, but before that condition is reached (counter overflow)
several context switches will have restored FP and vector registers without
need, causing a performance degradation.
Fixes: 70fe3d980f ("powerpc: Restore FPU/VEC/VSX if previously used")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Gustavo Romero <gusbromero@gmail.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
By default, 5% of system RAM is reserved for preserving boot memory.
Alternatively, a user can specify the amount of memory to reserve.
See Documentation/powerpc/firmware-assisted-dump.txt for details. In
addition to the memory reserved for preserving boot memory, some more
memory is reserved, to save HPTE region, CPU state data and ELF core
headers.
Memory Reservation during first kernel looks like below:
Low memory Top of memory
0 boot memory size |
| | |<--Reserved dump area -->|
V V | Permanent Reservation V
+-----------+----------/ /----------+---+----+-----------+----+
| | |CPU|HPTE| DUMP |ELF |
+-----------+----------/ /----------+---+----+-----------+----+
| ^
| |
\ /
-------------------------------------------
Boot memory content gets transferred to
reserved area by firmware at the time of
crash
This implicitly means that the sum of the sizes of boot memory, CPU
state data, HPTE region, DUMP preserving area and ELF core headers
can't be greater than the total memory size. But currently, a user is
allowed to specify any value as boot memory size. So, the above rule
is violated when a boot memory size around 50% of the total available
memory is specified. As the kernel is not handling this currently, it
may lead to undefined behavior. Fix it by setting an upper limit for
boot memory size to 25% of the total available memory. Also, instead
of using memblock_end_of_DRAM(), which doesn't take the holes, if any,
in the memory layout into account, use memblock_phys_mem_size() to
calculate the percentage of total available memory.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With commit f6e6bedb77 ("powerpc/fadump: Reserve memory at an offset
closer to bottom of RAM"), memory for fadump is no longer reserved at
the top of RAM. But there are still a few places which say so. Change
them appropriately.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With commit 11550dc0a0 ("powerpc/fadump: reuse crashkernel parameter
for fadump memory reservation"), 'fadump_reserve_mem=' parameter is
deprecated in favor of 'crashkernel=' parameter. Add a warning if
'fadump_reserve_mem=' is still used.
Fixes: 11550dc0a0 ("powerpc/fadump: reuse crashkernel parameter for fadump memory reservation")
Suggested-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
[mpe: Unsplit long printk strings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- log an error message when registration fails and no error code listed
in the switch is returned
- translate the hv error code to posix error code and return it from
fw_register
- return the posix error code from fw_register to the process writing
to sysfs
- return EEXIST on re-registration
- return success on deregistration when fadump is not registered
- return ENODEV when no memory is reserved for fadump
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Tested-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
[mpe: Use pr_err() to shrink the error print]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It often happens to have simultaneous interrupts, for instance
when having double Ethernet attachment. With the current
implementation, we suffer the cost of kernel entry/exit for each
interrupt.
This patch introduces a loop in __do_irq() to handle all interrupts
at once before returning.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are running low on CPU feature bits, so we only want to use them when
it's really necessary.
CPU_FTR_SUBCORE is only used in one place, and only in C, so we don't
need it in order to make asm patching work. It can only be set on
"Power8" CPUs, which in practice means POWER8, POWER8E and POWER8NVL.
There are no plans to implement it on future CPUs, but if there ever
were we could retrofit it then.
Although KVM uses subcores, it never looks at the CPU feature, it either
looks at the ISA level or the threads_per_subcore value.
So drop the CPU feature and do a PVR check instead. Drop the device tree
"subcore" feature as we no longer support doing anything with it, and we
will drop it from skiboot too.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Provide a dt_cpu_ftrs= cmdline option to disable the dt_cpu_ftrs CPU
feature discovery, and fall back to the "cputable" based version.
Also allow control of advertising unknown features to userspace and
with this parameter, and remove the clunky CONFIG option.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add explicit early check of bootargs in dt_cpu_ftrs_init()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add --orphan-handling=warn to final link flags. This ensures we can
handle all sections explicitly. This would have caught subtle breakage
such as 7de3b27bac at build-time.
Also bring existing orphan sections into the fold:
- .text.hot and .text.unlikely are compiler generated sections.
- .sdata2, .dynsbss, .plt are used by PPC32
- We previously did not specify DWARF_DEBUG or STABS_DEBUG
- DWARF_DEBUG did not include all DWARF sections that can be emitted
- A number of sections are unused and can be discarded.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use a tool to check that the location of "fixed sections" are where
we expected them to be, which catches cases the linker script can't
(stubs being added to start of .text section), and which ends up
being neater.
Sample output:
ERROR: start_text address is c000000000008100, should be c000000000008000
ERROR: see comments in arch/powerpc/tools/head_check.sh
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Fold in fix from Nick for 4.6 era toolchains]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Very large kernels may require linker stubs for branches from HEAD
text code. The linker may place these stubs before the HEAD text
sections, which breaks the assumption that HEAD text is located at 0
(or the .text section being located at 0x7000/0x8000 on Book3S
kernels).
Provide an option to create a small section just before the .text
section with an empty 256 - 4 bytes, and adjust the start of the .text
section to match. The linker will tend to put stubs in that section
and not break our relative-to-absolute offset assumptions.
This causes a small waste of space on common kernels, but allows large
kernels to build and boot. For now, it is an EXPERT config option,
defaulting to =n, but a reference is provided for it in the build-time
check for such breakage. This is good enough for allyesconfig and
custom users / hackers.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Prevent a kernel panic caused by unintentionally clearing TCR watchdog
bits. At this point in the kernel boot, the watchdog may have already
been enabled by u-boot. The original code's attempt to write to the TCR
register results in an inadvertent clearing of the watchdog
configuration bits, causing the 476 to reset.
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On Power9 DD1 due to a hardware bug the Power-Saving Level Status
field (PLS) of the PSSCR for a thread waking up from a deep state can
under-report if some other thread in the core is in a shallow stop
state. The scenario in which this can manifest is as follows:
1) All the threads of the core are in deep stop.
2) One of the threads is woken up. The PLS for this thread will
correctly reflect that it is waking up from deep stop.
3) The thread that has woken up now executes a shallow stop.
4) When some other thread in the core is woken, its PLS will reflect
the shallow stop state.
Thus, the subsequent thread for which the PLS is under-reporting the
wakeup state will not restore the hypervisor resources.
Hence, on DD1 systems, use the Requested Level (RL) field as a
workaround to restore the contents of the hypervisor resources on the
wakeup from the stop state.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On wakeup from a deep stop state which is supposed to lose the
hypervisor state, we don't restore the LPCR to the old value but set
it to a "sane" value via cur_cpu_spec->cpu_restore().
The problem is that the "sane" value doesn't include UPRT and the HR
bits which are required to run correctly in Radix mode.
Fix this on POWER9 onwards by restoring the LPCR value whatever it was
before executing the stop instruction.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER8, in case of
- nap: both timebase and hypervisor state is retained.
- fast-sleep: timebase is lost. But the hypervisor state is retained.
- winkle: timebase and hypervisor state is lost.
Hence, the current code for handling exit from a idle state assumes
that if the timebase value is retained, then so is the hypervisor
state. Thus, the current code doesn't restore per-core hypervisor
state in such cases.
But that is no longer the case on POWER9 where we do have stop states
in which timebase value is retained, but the hypervisor state is
lost. So we have to ensure that the per-core hypervisor state gets
restored in such cases.
Fix this by ensuring that even in the case when timebase is retained,
we explicitly check if we are waking up from a deep stop that loses
per-core hypervisor state (indicated by cr4 being eq or gt), and if
this is the case, we restore the per-core hypervisor state.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Providing "scv" support to userspace requires kernel support, so it
must be advertised as independently to the base ISA 3 instruction set.
The darn instruction relies on firmware enablement, so it has been
decided to split this out from the core ISA 3 feature as well.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently if you disable CONFIG_PPC_RADIX_MMU you'll crash on boot on
a P9. This is because we still set MMU_FTR_TYPE_RADIX via
ibm,pa-features and MMU_FTR_TYPE_RADIX is what's used for code patching
in much of the asm code (ie. slb_miss_realmode)
This patch fixes the problem by stopping MMU_FTR_TYPE_RADIX from being
set from ibm.pa-features.
We may eventually end up removing the CONFIG_PPC_RADIX_MMU option
completely but until then this fixes the issue.
Fixes: 17a3dd2f5f ("powerpc/mm/radix: Use firmware feature to enable Radix MMU")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To enable smp_processor_id() and might_sleep() debug checks earlier, it's
required to add system states between SYSTEM_BOOTING and SYSTEM_RUNNING.
Adjust the system_state check in smp_generic_cpu_bootable() to handle the
extra states.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20170516184735.359536998@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 22d8b3dec2 ("powerpc/kprobes: Emulate instructions on kprobe
handler re-entry") enabled emulating instructions on kprobe re-entry,
rather than single-stepping always. However, we didn't update the single
stepping code to only be run if the emulation fails. Also, we missed
re-enabling preemption if the instruction emulation was successful. Fix
those issues.
Fixes: 22d8b3dec2 ("powerpc/kprobes: Emulate instructions on kprobe handler re-entry")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 17ed4c8f81 ("powerpc/powernv: Recover correct PACA on wakeup
from a stop on P9 DD1") promises to set the NAPSTATELOST bit in paca
after recovering the correct paca for the thread waking up from stop1
on DD1, so that the GPRs can be correctly restored on the stop exit
path. However, it loads the value 1 into r3, but stores the value in
r0 into NAPSTATELOST(r13).
Fix this by correctly set the NAPSTATELOST bit in paca after
recovering the paca on POWER9 DD1.
Fixes: 17ed4c8f81 ("powerpc/powernv: Recover correct PACA on wakeup from a stop on P9 DD1")
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit dc3106690b ("powerpc: tm: Always use fp_state and vr_state
to store live registers"), a section of code was removed that copied
the current state to checkpointed state. That code should not have been
removed.
When an FP (Floating Point) unavailable is taken inside a transaction,
we need to abort the transaction. This is because at the time of the
tbegin, the FP state is bogus so the state stored in the checkpointed
registers is incorrect. To fix this, we treclaim (to get the
checkpointed GPRs) and then copy the thread_struct FP live state into
the checkpointed state. We then trecheckpoint so that the FP state is
correctly restored into the CPU.
The copying of the FP registers from live to checkpointed is what was
missing.
This simplifies the logic slightly from the original patch.
tm_reclaim_thread() will now always write the checkpointed FP
state. Either the checkpointed FP state will be written as part of
the actual treclaim (in tm.S), or it'll be a copy of the live
state. Which one we use is based on MSR[FP] from userspace.
Similarly for VMX.
Fixes: dc3106690b ("powerpc: tm: Always use fp_state and vr_state to store live registers")
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: cyrilbur@gmail.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights include:
- rework the Linux page table geometry to lower memory usage on 64-bit Book3S
(IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features on future
firmwares.
- Freescale updates from Scott: "Includes a fix for a powerpc/next mm regression
on 64e, a fix for a kernel hang on 64e when using a debugger inside a
relocated kernel, a qman fix, and misc qe improvements."
Thanks to:
Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong, Nicholas Piggin, Roy
Pledge, Scott Wood, Valentin Longchamp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YOQs
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"The change to the Linux page table geometry was delayed for more
testing with 16G pages, and there's the new CPU features stuff which
just needed one more polish before going in. Plus a few changes from
Scott which came in a bit late. And then various fixes, mostly minor.
Summary highlights:
- rework the Linux page table geometry to lower memory usage on
64-bit Book3S (IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features
on future firmwares.
- Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for
a kernel hang on 64e when using a debugger inside a relocated
kernel, a qman fix, and misc qe improvements."
Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"
* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Support new device tree binding for discovering CPU features
powerpc: Don't print cpu_spec->cpu_name if it's NULL
of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
powerpc/64s: Fix unnecessary machine check handler relocation branch
powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
powerpc: Fix distclean with Makefile.postlink
powerpc/64e: Don't place the stack beyond TASK_SIZE
powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
soc/fsl/qbman: Disable IRQs for deferred QBMan work
soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
soc/fsl/qe: round brg_freq to 1kHz granularity
soc/fsl/qe: get rid of immrbar_virt_to_phys()
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
powerpc/64e: Fix hang when debugging programs with relocated kernel
The ibm,powerpc-cpu-features device tree binding describes CPU features with
ASCII names and extensible compatibility, privilege, and enablement metadata
that allows improved flexibility and compatibility with new hardware.
The interface is described in detail in ibm,powerpc-cpu-features.txt in this
patch.
Currently this code is not enabled by default, and there are no released
firmwares that provide the binding.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we assume that if the cpu_spec has a pvr_mask then it must also have a
cpu_name. But that will change in a subsequent commit when we do CPU feature
discovery via the device tree, so check explicitly if cpu_name is NULL.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for a
kernel hang on 64e when using a debugger inside a relocated kernel, a
qman fix, and misc qe improvements."
The main thing here is a new implementation of the in-kernel
XICS interrupt controller emulation for POWER9 machines, from Ben
Herrenschmidt.
POWER9 has a new interrupt controller called XIVE (eXternal Interrupt
Virtualization Engine) which is able to deliver interrupts directly
to guest virtual CPUs in hardware without hypervisor intervention.
With this new code, the guest still sees the old XICS interface but
performance is better because the XICS emulation in the host uses the
XIVE directly rather than going through a XICS emulation in firmware.
Conflicts:
arch/powerpc/kernel/cpu_setup_power.S [cherry-picked fix]
arch/powerpc/kvm/book3s_xive.c [include asm/debugfs.h]
Similarly to commit 2563a70c3b ("powerpc/64s: Remove unnecessary relocation
branch from idle handler"), the machine check handler has a BRANCH_TO from
relocated to relocated code, which is unnecessary.
It has also caused build errors with some toolchains:
arch/powerpc/kernel/exceptions-64s.S: Assembler messages:
arch/powerpc/kernel/exceptions-64s.S:395: Error: operand out of range
(0xffffffffffff8280 is not between 0x0000000000000000 and
0x000000000000ffff)
Fixes: 1945bc4549 ("powerpc/64s: Fix POWER9 machine check handler from stop state")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reported-and-tested-by : Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eE4D
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- add framework for supporting PCIe devices in Endpoint mode (Kishon
Vijay Abraham I)
- use non-postable PCI config space mappings when possible (Lorenzo
Pieralisi)
- clean up and unify mmap of PCI BARs (David Woodhouse)
- export and unify Function Level Reset support (Christoph Hellwig)
- avoid FLR for Intel 82579 NICs (Sasha Neftin)
- add pci_request_irq() and pci_free_irq() helpers (Christoph Hellwig)
- short-circuit config access failures for disconnected devices (Keith
Busch)
- remove D3 sleep delay when possible (Adrian Hunter)
- freeze PME scan before suspending devices (Lukas Wunner)
- stop disabling MSI/MSI-X in pci_device_shutdown() (Prarit Bhargava)
- disable boot interrupt quirk for ASUS M2N-LR (Stefan Assmann)
- add arch-specific alignment control to improve device passthrough by
avoiding multiple BARs in a page (Yongji Xie)
- add sysfs sriov_drivers_autoprobe to control VF driver binding
(Bodong Wang)
- allow slots below PCI-to-PCIe "reverse bridges" (Bjorn Helgaas)
- fix crashes when unbinding host controllers that don't support
removal (Brian Norris)
- add driver for MicroSemi Switchtec management interface (Logan
Gunthorpe)
- add driver for Faraday Technology FTPCI100 host bridge (Linus
Walleij)
- add i.MX7D support (Andrey Smirnov)
- use generic MSI support for Aardvark (Thomas Petazzoni)
- make Rockchip driver modular (Brian Norris)
- advertise 128-byte Read Completion Boundary support for Rockchip
(Shawn Lin)
- advertise PCI_EXP_LNKSTA_SLC for Rockchip root port (Shawn Lin)
- convert atomic_t to refcount_t in HV driver (Elena Reshetova)
- add CPU IRQ affinity in HV driver (K. Y. Srinivasan)
- fix PCI bus removal in HV driver (Long Li)
- add support for ThunderX2 DMA alias topology (Jayachandran C)
- add ThunderX pass2.x 2nd node MCFG quirk (Tomasz Nowicki)
- add ITE 8893 bridge DMA alias quirk (Jarod Wilson)
- restrict Cavium ACS quirk only to CN81xx/CN83xx/CN88xx devices
(Manish Jaggi)
* tag 'pci-v4.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (146 commits)
PCI: Don't allow unbinding host controllers that aren't prepared
ARM: DRA7: clockdomain: Change the CLKTRCTRL of CM_PCIE_CLKSTCTRL to SW_WKUP
MAINTAINERS: Add PCI Endpoint maintainer
Documentation: PCI: Add userguide for PCI endpoint test function
tools: PCI: Add sample test script to invoke pcitest
tools: PCI: Add a userspace tool to test PCI endpoint
Documentation: misc-devices: Add Documentation for pci-endpoint-test driver
misc: Add host side PCI driver for PCI test function device
PCI: Add device IDs for DRA74x and DRA72x
dt-bindings: PCI: dra7xx: Add DT bindings to enable unaligned access
PCI: dwc: dra7xx: Workaround for errata id i870
dt-bindings: PCI: dra7xx: Add DT bindings for PCI dra7xx EP mode
PCI: dwc: dra7xx: Add EP mode support
PCI: dwc: dra7xx: Facilitate wrapper and MSI interrupts to be enabled independently
dt-bindings: PCI: Add DT bindings for PCI designware EP mode
PCI: dwc: designware: Add EP mode support
Documentation: PCI: Add binding documentation for pci-test endpoint function
ixgbe: Use pcie_flr() instead of duplicating it
IB/hfi1: Use pcie_flr() instead of duplicating it
PCI: imx6: Fix spelling mistake: "contol" -> "control"
...
Merge more updates from Andrew Morton:
- the rest of MM
- various misc things
- procfs updates
- lib/ updates
- checkpatch updates
- kdump/kexec updates
- add kvmalloc helpers, use them
- time helper updates for Y2038 issues. We're almost ready to remove
current_fs_time() but that awaits a btrfs merge.
- add tracepoints to DAX
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (114 commits)
drivers/staging/ccree/ssi_hash.c: fix build with gcc-4.4.4
selftests/vm: add a test for virtual address range mapping
dax: add tracepoint to dax_insert_mapping()
dax: add tracepoint to dax_writeback_one()
dax: add tracepoints to dax_writeback_mapping_range()
dax: add tracepoints to dax_load_hole()
dax: add tracepoints to dax_pfn_mkwrite()
dax: add tracepoints to dax_iomap_pte_fault()
mtd: nand: nandsim: convert to memalloc_noreclaim_*()
treewide: convert PF_MEMALLOC manipulations to new helpers
mm: introduce memalloc_noreclaim_{save,restore}
mm: prevent potential recursive reclaim due to clearing PF_MEMALLOC
mm/huge_memory.c: deposit a pgtable for DAX PMD faults when required
mm/huge_memory.c: use zap_deposited_table() more
time: delete CURRENT_TIME_SEC and CURRENT_TIME
gfs2: replace CURRENT_TIME with current_time
apparmorfs: replace CURRENT_TIME with current_time()
lustre: replace CURRENT_TIME macro
fs: ubifs: replace CURRENT_TIME_SEC with current_time
fs: ufs: use ktime_get_real_ts64() for birthtime
...
fadump supports specifying memory to reserve for fadump's crash kernel
with fadump_reserve_mem kernel parameter. This parameter currently
supports passing a fixed memory size, like fadump_reserve_mem=<size>
only. This patch aims to add support for other syntaxes like
range-based memory size
<range1>:<size1>[,<range2>:<size2>,<range3>:<size3>,...] which allows
using the same parameter to boot the kernel with different system RAM
sizes.
As crashkernel parameter already supports the above mentioned syntaxes,
this patch deprecates fadump_reserve_mem parameter and reuses
crashkernel parameter instead, to specify memory for fadump's crash
kernel memory reservation as well. If any offset is provided in
crashkernel parameter, it will be ignored in case of fadump, as fadump
reserves memory at end of RAM.
Advantages using crashkernel parameter instead of fadump_reserve_mem
parameter are one less kernel parameter overall, code reuse and support
for multiple syntaxes to specify memory.
Suggested-by: Dave Young <dyoung@redhat.com>
Link: http://lkml.kernel.org/r/149035346749.6881.911095631212975718.stgit@hbathini.in.ibm.com
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that crashkernel parameter parsing and vmcoreinfo related code is
moved under CONFIG_CRASH_CORE instead of CONFIG_KEXEC_CORE, remove
dependency with CONFIG_KEXEC for CONFIG_FA_DUMP. While here, get rid of
definitions of fadump_append_elf_note() & fadump_final_note() functions
to reuse similar functions compiled under CONFIG_CRASH_CORE.
Link: http://lkml.kernel.org/r/149035343956.6881.1536459326017709354.stgit@hbathini.in.ibm.com
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
support; virtual interrupt controller performance improvements; support
for userspace virtual interrupt controller (slower, but necessary for
KVM on the weird Broadcom SoCs used by the Raspberry Pi 3)
* MIPS: basic support for hardware virtualization (ImgTec
P5600/P6600/I6400 and Cavium Octeon III)
* PPC: in-kernel acceleration for VFIO
* s390: support for guests without storage keys; adapter interruption
suppression
* x86: usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits; emulation of CPL3 CPUID faulting
* generic: first part of VCPU thread request API; kvm_stat improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJZEHUkAAoJEL/70l94x66DBeYH/09wrpJ2FjU4Rqv7FxmqgWfH
9WGi4wvn/Z+XzQSyfMJiu2SfZVzU69/Y67OMHudy7vBT6knB+ziM7Ntoiu/hUfbG
0g5KsDX79FW15HuvuuGh9kSjUsj7qsQdyPZwP4FW/6ZoDArV9mibSvdjSmiUSMV/
2wxaoLzjoShdOuCe9EABaPhKK0XCrOYkygT6Paz1pItDxaSn8iW3ulaCuWMprUfG
Niq+dFemK464E4yn6HVD88xg5j2eUM6bfuXB3qR3eTR76mHLgtwejBzZdDjLG9fk
32PNYKhJNomBxHVqtksJ9/7cSR6iNPs7neQ1XHemKWTuYqwYQMlPj1NDy0aslQU=
=IsiZ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"ARM:
- HYP mode stub supports kexec/kdump on 32-bit
- improved PMU support
- virtual interrupt controller performance improvements
- support for userspace virtual interrupt controller (slower, but
necessary for KVM on the weird Broadcom SoCs used by the Raspberry
Pi 3)
MIPS:
- basic support for hardware virtualization (ImgTec P5600/P6600/I6400
and Cavium Octeon III)
PPC:
- in-kernel acceleration for VFIO
s390:
- support for guests without storage keys
- adapter interruption suppression
x86:
- usual range of nVMX improvements, notably nested EPT support for
accessed and dirty bits
- emulation of CPL3 CPUID faulting
generic:
- first part of VCPU thread request API
- kvm_stat improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (227 commits)
kvm: nVMX: Don't validate disabled secondary controls
KVM: put back #ifndef CONFIG_S390 around kvm_vcpu_kick
Revert "KVM: Support vCPU-based gfn->hva cache"
tools/kvm: fix top level makefile
KVM: x86: don't hold kvm->lock in KVM_SET_GSI_ROUTING
KVM: Documentation: remove VM mmap documentation
kvm: nVMX: Remove superfluous VMX instruction fault checks
KVM: x86: fix emulation of RSM and IRET instructions
KVM: mark requests that need synchronization
KVM: return if kvm_vcpu_wake_up() did wake up the VCPU
KVM: add explicit barrier to kvm_vcpu_kick
KVM: perform a wake_up in kvm_make_all_cpus_request
KVM: mark requests that do not need a wakeup
KVM: remove #ifndef CONFIG_S390 around kvm_vcpu_wake_up
KVM: x86: always use kvm_make_request instead of set_bit
KVM: add kvm_{test,clear}_request to replace {test,clear}_bit
s390: kvm: Cpu model support for msa6, msa7 and msa8
KVM: x86: remove irq disablement around KVM_SET_CLOCK/KVM_GET_CLOCK
kvm: better MWAIT emulation for guests
KVM: x86: virtualize cpuid faulting
...
Highlights include:
- Larger virtual address space on 64-bit server CPUs. By default we use a 128TB
virtual address space, but a process can request access to the full 512TB by
passing a hint to mmap().
- Support for the new Power9 "XIVE" interrupt controller.
- TLB flushing optimisations for the radix MMU on Power9.
- Support for CAPI cards on Power9, using the "Coherent Accelerator Interface
Architecture 2.0".
- The ability to configure the mmap randomisation limits at build and runtime.
- Several small fixes and cleanups to the kprobes code, as well as support for
KPROBES_ON_FTRACE.
- Major improvements to handling of system reset interrupts, correctly treating
them as NMIs, giving them a dedicated stack and using a new hypervisor call
to trigger them, all of which should aid debugging and robustness.
Many fixes and other minor enhancements.
Thanks to:
Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anshuman Khandual, Anton Blanchard, Balbir Singh, Ben
Hutchings, Benjamin Herrenschmidt, Bhupesh Sharma, Chris Packham, Christian
Zigotzky, Christophe Leroy, Christophe Lombard, Daniel Axtens, David Gibson,
Gautham R. Shenoy, Gavin Shan, Geert Uytterhoeven, Guilherme G. Piccoli,
Hamish Martin, Hari Bathini, Kees Cook, Laurent Dufour, Madhavan Srinivasan,
Mahesh J Salgaonkar, Mahesh Salgaonkar, Masami Hiramatsu, Matt Brown, Matthew
R. Ochs, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Oliver O'Halloran,
Pan Xinhui, Paul Mackerras, Rashmica Gupta, Russell Currey, Sukadev
Bhattiprolu, Thadeu Lima de Souza Cascardo, Tobin C. Harding, Tyrel Datwyler,
Uma Krishnan, Vaibhav Jain, Vipin K Parashar, Yang Shi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZDHUMAAoJEFHr6jzI4aWAT7oQALkE2Nj3gjcn1z0SkFhq/1iO
Py9Elmqm4E+L6NKYtBY5dS8xVAJ088ffzERyqJ1FY1LHkB8tn8bWRcMQmbjAFzTI
V4TAzDNI890BN/F4ptrYRwNFxRBHAvZ4NDunTzagwYnwmTzW9PYHmOi4pvWTo3Tw
KFUQ0joLSEgHzyfXxYB3fyj41u8N0FZvhfazdNSqia2Y5Vwwv/ION5jKplDM+09Y
EtVEXFvaKAS1sjbM/d/Jo5rblHfR0D9/lYV10+jjyIokjzslIpyTbnj3izeYoM5V
I4h99372zfsEjBGPPXyM3khL3zizGMSDYRmJHQSaKxjtecS9SPywPTZ8ufO/aSzV
Ngq6nlND+f1zep29VQ0cxd3Jh40skWOXzxJaFjfDT25xa6FbfsWP2NCtk8PGylZ7
EyqTuCWkMgIP02KlX3oHvEB2LRRPCDmRU2zECecRGNJrIQwYC2xjoiVi7Q8Qe8rY
gr7Ib5Jj/a+uiTcCIy37+5nXq2s14/JBOKqxuYZIxeuZFvKYuRUipbKWO05WDOAz
m/pSzeC3J8AAoYiqR0gcSOuJTOnJpGhs7zrQFqnEISbXIwLW+ICumzOmTAiBqOEY
Rt8uW2gYkPwKLrE05445RfVUoERaAjaE06eRMOWS6slnngHmmnRJbf3PcoALiJkT
ediqGEj0/N1HMB31V5tS
=vSF3
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Larger virtual address space on 64-bit server CPUs. By default we
use a 128TB virtual address space, but a process can request access
to the full 512TB by passing a hint to mmap().
- Support for the new Power9 "XIVE" interrupt controller.
- TLB flushing optimisations for the radix MMU on Power9.
- Support for CAPI cards on Power9, using the "Coherent Accelerator
Interface Architecture 2.0".
- The ability to configure the mmap randomisation limits at build and
runtime.
- Several small fixes and cleanups to the kprobes code, as well as
support for KPROBES_ON_FTRACE.
- Major improvements to handling of system reset interrupts,
correctly treating them as NMIs, giving them a dedicated stack and
using a new hypervisor call to trigger them, all of which should
aid debugging and robustness.
- Many fixes and other minor enhancements.
Thanks to: Alastair D'Silva, Alexey Kardashevskiy, Alistair Popple,
Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual, Anton
Blanchard, Balbir Singh, Ben Hutchings, Benjamin Herrenschmidt,
Bhupesh Sharma, Chris Packham, Christian Zigotzky, Christophe Leroy,
Christophe Lombard, Daniel Axtens, David Gibson, Gautham R. Shenoy,
Gavin Shan, Geert Uytterhoeven, Guilherme G. Piccoli, Hamish Martin,
Hari Bathini, Kees Cook, Laurent Dufour, Madhavan Srinivasan, Mahesh J
Salgaonkar, Mahesh Salgaonkar, Masami Hiramatsu, Matt Brown, Matthew
R. Ochs, Michael Neuling, Naveen N. Rao, Nicholas Piggin, Oliver
O'Halloran, Pan Xinhui, Paul Mackerras, Rashmica Gupta, Russell
Currey, Sukadev Bhattiprolu, Thadeu Lima de Souza Cascardo, Tobin C.
Harding, Tyrel Datwyler, Uma Krishnan, Vaibhav Jain, Vipin K Parashar,
Yang Shi"
* tag 'powerpc-4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (214 commits)
powerpc/64s: Power9 has no LPCR[VRMASD] field so don't set it
powerpc/powernv: Fix TCE kill on NVLink2
powerpc/mm/radix: Drop support for CPUs without lockless tlbie
powerpc/book3s/mce: Move add_taint() later in virtual mode
powerpc/sysfs: Move #ifdef CONFIG_HOTPLUG_CPU out of the function body
powerpc/smp: Document irq enable/disable after migrating IRQs
powerpc/mpc52xx: Don't select user-visible RTAS_PROC
powerpc/powernv: Document cxl dependency on special case in pnv_eeh_reset()
powerpc/eeh: Clean up and document event handling functions
powerpc/eeh: Avoid use after free in eeh_handle_special_event()
cxl: Mask slice error interrupts after first occurrence
cxl: Route eeh events to all drivers in cxl_pci_error_detected()
cxl: Force context lock during EEH flow
powerpc/64: Allow CONFIG_RELOCATABLE if COMPILE_TEST
powerpc/xmon: Teach xmon oops about radix vectors
powerpc/mm/hash: Fix off-by-one in comment about kernel contexts ids
powerpc/pseries: Enable VFIO
powerpc/powernv: Fix iommu table size calculation hook for small tables
powerpc/powernv: Check kzalloc() return value in pnv_pci_table_alloc
powerpc: Add arch/powerpc/tools directory
...
Power9/ISAv3 has no VRMASD field in LPCR, we shouldn't be setting reserved bits,
so don't set them on Power9.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
machine_check_early() gets called in real mode. The very first time when
add_taint() is called, it prints a warning which ends up calling opal
call (that uses OPAL_CALL wrapper) for writing it to console. If we get a
very first machine check while we are in opal we are doomed. OPAL_CALL
overwrites the PACASAVEDMSR in r13 and in this case when we are done with
MCE handling the original opal call will use this new MSR on it's way
back to opal_return. This usually leads to unexpected behaviour or the
kernel to panic. Instead move the add_taint() call later in the virtual
mode where it is safe to call.
This is broken with current FW level. We got lucky so far for not getting
very first MCE hit while in OPAL. But easily reproducible on Mambo.
Fixes: 27ea2c420c ("powerpc: Set the correct kernel taint on machine check errors.")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The entire body of unregister_cpu_online() is inside an #ifdef
CONFIG_HOTPLUG_CPU block. This is ugly and means we create an empty function
when hotplug is disabled for no reason.
Instead move the #ifdef out of the function body and define the function to be
NULL in the else case. This means we'll pass NULL to cpuhp_setup_state(), but
that's fine because it accepts NULL to mean there is no teardown callback, which
is exactly what we want.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This code was until recently completely undocumented and even now the comment is
not very verbose.
We've already had one patch sent to remove the IRQ enable/disable because it's
"paradoxical and unnecessary". So document it thoroughly to save anyone else
from puzzling over it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull livepatch updates from Jiri Kosina:
- a per-task consistency model is being added for architectures that
support reliable stack dumping (extending this, currently rather
trivial set, is currently in the works).
This extends the nature of the types of patches that can be applied
by live patching infrastructure. The code stems from the design
proposal made [1] back in November 2014. It's a hybrid of SUSE's
kGraft and RH's kpatch, combining advantages of both: it uses
kGraft's per-task consistency and syscall barrier switching combined
with kpatch's stack trace switching. There are also a number of
fallback options which make it quite flexible.
Most of the heavy lifting done by Josh Poimboeuf with help from
Miroslav Benes and Petr Mladek
[1] https://lkml.kernel.org/r/20141107140458.GA21774@suse.cz
- module load time patch optimization from Zhou Chengming
- a few assorted small fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
livepatch: add missing printk newlines
livepatch: Cancel transition a safe way for immediate patches
livepatch: Reduce the time of finding module symbols
livepatch: make klp_mutex proper part of API
livepatch: allow removal of a disabled patch
livepatch: add /proc/<pid>/patch_state
livepatch: change to a per-task consistency model
livepatch: store function sizes
livepatch: use kstrtobool() in enabled_store()
livepatch: move patching functions into patch.c
livepatch: remove unnecessary object loaded check
livepatch: separate enabled and patched states
livepatch/s390: add TIF_PATCH_PENDING thread flag
livepatch/s390: reorganize TIF thread flag bits
livepatch/powerpc: add TIF_PATCH_PENDING thread flag
livepatch/x86: add TIF_PATCH_PENDING thread flag
livepatch: create temporary klp_update_patch_state() stub
x86/entry: define _TIF_ALLWORK_MASK flags explicitly
stacktrace/x86: add function for detecting reliable stack traces
- restore powerpc dumping; Ankit Kumar
- fix more bugs in the rarely exercises module unloading logic
- reorganize filesystem locking to fix problems noticed by lockdep
- refactor internal pstore APIs to make development and review easier:
- improve error reporting
- add kernel-doc structure and function comments
- avoid insane argument passing by using a common record structure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=S14G
-----END PGP SIGNATURE-----
Merge tag 'pstore-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"This has a large internal refactoring along with several smaller
fixes.
- constify compression structures; Bhumika Goyal
- restore powerpc dumping; Ankit Kumar
- fix more bugs in the rarely exercises module unloading logic
- reorganize filesystem locking to fix problems noticed by lockdep
- refactor internal pstore APIs to make development and review
easier:
- improve error reporting
- add kernel-doc structure and function comments
- avoid insane argument passing by using a common record
structure"
* tag 'pstore-v4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (23 commits)
pstore: Solve lockdep warning by moving inode locks
pstore: Fix flags to enable dumps on powerpc
pstore: Remove unused vmalloc.h in pmsg
pstore: simplify write_user_compat()
pstore: Remove write_buf() callback
pstore: Replace arguments for write_buf_user() API
pstore: Replace arguments for write_buf() API
pstore: Replace arguments for erase() API
pstore: Do not duplicate record metadata
pstore: Allocate records on heap instead of stack
pstore: Pass record contents instead of copying
pstore: Always allocate buffer for decompression
pstore: Replace arguments for write() API
pstore: Replace arguments for read() API
pstore: Switch pstore_mkfile to pass record
pstore: Move record decompression to function
pstore: Extract common arguments into structure
pstore: Add kernel-doc for struct pstore_info
pstore: Improve register_pstore() error reporting
pstore: Avoid race in module unloading
...
Remove unnecessary tags in eeh_handle_normal_event(), and add function
comments for eeh_handle_normal_event() and eeh_handle_special_event().
The only functional difference is that in the case of a PE reaching the
maximum number of failures, rather than one message telling you of this
and suggesting you reseat the device, there are two separate messages.
Suggested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_handle_special_event() is called when an EEH event is detected but
can't be narrowed down to a specific PE. This function looks through
every PE to find one in an erroneous state, then calls the regular event
handler eeh_handle_normal_event() once it knows which PE has an error.
However, if eeh_handle_normal_event() found that the PE cannot possibly
be recovered, it will free it, rendering the passed PE stale.
This leads to a use after free in eeh_handle_special_event() as it attempts to
clear the "recovering" state on the PE after eeh_handle_normal_event() returns.
Thus, make sure the PE is valid when attempting to clear state in
eeh_handle_special_event().
Fixes: 8a6b1bc70d ("powerpc/eeh: EEH core to handle special event")
Cc: stable@vger.kernel.org # v3.11+
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull x86 asm updates from Ingo Molnar:
"The main changes in this cycle were:
- unwinder fixes and enhancements
- improve ftrace interaction with the unwinder
- optimize the code footprint of WARN() and related debugging
constructs
- ... plus misc updates, cleanups and fixes"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/unwind: Dump all stacks in unwind_dump()
x86/unwind: Silence more entry-code related warnings
x86/ftrace: Fix ebp in ftrace_regs_caller that screws up unwinder
x86/unwind: Remove unused 'sp' parameter in unwind_dump()
x86/unwind: Prepend hex mask value with '0x' in unwind_dump()
x86/unwind: Properly zero-pad 32-bit values in unwind_dump()
x86/unwind: Ensure stack pointer is aligned
debug: Avoid setting BUGFLAG_WARNING twice
x86/unwind: Silence entry-related warnings
x86/unwind: Read stack return address in update_stack_state()
x86/unwind: Move common code into update_stack_state()
debug: Fix __bug_table[] in arch linker scripts
debug: Add _ONCE() logic to report_bug()
x86/debug: Define BUG() again for !CONFIG_BUG
x86/debug: Implement __WARN() using UD0
x86/ftrace: Use Makefile logic instead of #ifdef for compiling ftrace_*.o
x86/ftrace: Add -mfentry support to x86_32 with DYNAMIC_FTRACE set
x86/ftrace: Clean up ftrace_regs_caller
x86/ftrace: Add stack frame pointer to ftrace_caller
x86/ftrace: Move the ftrace specific code out of entry_32.S
...
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
Debug interrupts can be taken during interrupt entry, since interrupt
entry does not automatically turn them off. The kernel will check
whether the faulting instruction is between [interrupt_base_book3e,
__end_interrupts], and if so clear MSR[DE] and return.
However, when the kernel is built with CONFIG_RELOCATABLE, it can't use
LOAD_REG_IMMEDIATE(r14,interrupt_base_book3e) and
LOAD_REG_IMMEDIATE(r15,__end_interrupts), as they ignore relocation.
Thus, if the kernel is actually running at a different address than it
was built at, the address comparison will fail, and the exception entry
code will hang at kernel_dbg_exc.
r2(toc) is also not usable here, as r2 still holds data from the
interrupted context, so LOAD_REG_ADDR() doesn't work either. So we use
the *name@got* to get the EV of two labels directly.
Test programs test.c shows as follows:
int main(int argc, char *argv[])
{
if (access("/proc/sys/kernel/perf_event_paranoid", F_OK) == -1)
printf("Kernel doesn't have perf_event support\n");
}
Steps to reproduce the bug, for example:
1) ./gdb ./test
2) (gdb) b access
3) (gdb) r
4) (gdb) s
Signed-off-by: Liu Hailong <liu.hailong6@zte.com.cn>
Signed-off-by: Jiang Xuexin <jiang.xuexin@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Reviewed-by: Liu Song <liu.song11@zte.com.cn>
Reviewed-by: Huang Jian <huang.jian@zte.com.cn>
[scottwood: cleaned up commit message, and specified bad behavior
as a hang rather than an oops to correspond to mainline kernel behavior]
Fixes: 1cb6e06492 ("powerpc/book3e: support CONFIG_RELOCATABLE")
Cc: <stable@vger.kernel.org> # 4.4.x-
Signed-off-by: Scott Wood <oss@buserror.net>
* pci/resource-mmap:
ia64: Use generic pci_mmap_resource_range()
ia64: Remove redundant checks for WC in pci_mmap_page_range()
ia64: Remove redundant valid_mmap_phys_addr_range() from pci_mmap_page_range()
PCI: Add I/O BAR support to generic pci_mmap_resource_range()
x86/PCI: Use generic pci_mmap_resource_range()
unicore32/PCI: Use generic pci_mmap_resource_range()
sh/PCI: Use generic pci_mmap_resource_range()
parisc: Use generic pci_mmap_resource_range()
mn10300/PCI: Use generic pci_mmap_resource_range()
MIPS: PCI: Use generic pci_mmap_resource_range()
cris/PCI: Use generic pci_mmap_resource_range()
ARM/PCI: Use generic pci_mmap_resource_range()
PCI: Add pci_mmap_resource_range() and use it for ARM64
PCI: Add BAR index argument to pci_mmap_page_range()
PCI: Use BAR index in sysfs attr->private instead of resource pointer
PCI: Add arch_can_pci_mmap_io() on architectures which can mmap() I/O space
PCI: Move multiple declarations of pci_mmap_page_range() to <linux/pci.h>
PCI: Add arch_can_pci_mmap_wc() macro
xtensa/PCI: Do not mmap PCI BARs to userspace as write-through
PCI: Only allow WC mmap on prefetchable resources
PCI: Fix another sanity check bug in /proc/pci mmap
PCI: Fix pci_mmap_fits() for HAVE_PCI_RESOURCE_TO_USER platforms
Have the NMI IPI code use this op when the platform defines it.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a simple NMI IPI system that handles concurrency and reentrancy.
The platform does not have to implement a true non-maskable interrupt,
the default is to simply use the debugger break IPI message. This has
now been co-opted for a general IPI message, and users (debugger and
crash) have been reimplemented on top of the NMI system.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Incorporate incremental fixes from Nick]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
System reset is a non-maskable interrupt from Linux's point of view
(occurs under local_irq_disable()), so it should use nmi_enter/exit.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The system reset interrupt is used for crash/debug situations, so it is
desirable to have as little impact on the normal state of the system as
possible.
Currently it uses the current kernel stack to process the exception.
This stores into the stack which may be involved with the crash. The
stack pointer may be corrupted, or it may have overflowed.
Avoid or minimise these problems by creating a dedicated NMI stack for
the system reset interrupt to use.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In preparation for using a dedicated stack for system reset interrupts,
prevent a nested system reset from recovering, in order to simplify
code that is called in crash/debug path. This allows a system reset
interrupt to just use the base stack pointer.
Keep an in_nmi nesting counter similarly to the in_mce counter. Consider
the interrrupt non-recoverable if it is taken inside another system
reset.
Interrupt nesting could be allowed similarly to MCE, but system reset
is a special case that's not for normal operation, so simplicity wins
until there is requirement for nested system reset interrupts.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The system reset interrupt can occur when MSR_EE=0, and it currently
uses the PACA_EXGEN save area.
Some PACA_EXGEN interrupts have a window where MSR_RI=1 and MSR_EE=0
when the save area is still in use. A system reset interrupt in this
window can lead to undetected corruption when the save area gets
overwritten.
This patch introduces PACA_EXNMI save area for system reset exceptions,
which closes this corruption window. It's also helpful to retain the
EXGEN state for debugging situations, even if not considering the
recoverability aspect.
This patch also moves the PACA_EXMC area down to a less frequently used
part of the paca with the new save area.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This code is common to a few exceptions, and another user will be added.
This causes a trivial change to generated code:
- 604: std r9,416(r1)
- 608: mfspr r11,314
- 60c: std r11,368(r1)
- 610: mfspr r12,315
+ 604: mfspr r11,314
+ 608: mfspr r12,315
+ 60c: std r9,416(r1)
+ 610: std r11,368(r1)
machine_check_powernv_early could also use this, but that requires non
trivial changes to generated code, so that's for another patch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Subsequent patches will add more non-RI variant exceptions, so
create a macro for it rather than open-code it.
This does not change generated instructions.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This merges in the powerpc topic/xive branch to bring in the code for
the in-kernel XICS interrupt controller emulation to use the new XIVE
(eXternal Interrupt Virtualization Engine) hardware in the POWER9 chip
directly, rather than via a XICS emulation in firmware.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
After commit c950fd6f20 kernel registers pstore write based on flag set.
Pstore write for powerpc is broken as flags(PSTORE_FLAGS_DMESG) is not set for
powerpc architecture. On panic, kernel doesn't write message to
/fs/pstore/dmesg*(Entry doesn't gets created at all).
This patch enables pstore write for powerpc architecture by setting
PSTORE_FLAGS_DMESG flag.
Fixes: c950fd6f20 ("pstore: Split pstore fragile flags")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ankit Kumar <ankit@linux.vnet.ibm.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Split ftrace_64.S further retaining the core ftrace 64-bit aspects
in ftrace_64.S and moving ftrace_caller() and ftrace_graph_caller() into
separate files based on -mprofile-kernel. The livepatch routines are all
now contained within the mprofile file.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
entry_*.S now includes a lot more than just kernel entry/exit code. As a
first step at cleaning this up, let's split out the ftrace bits into
separate files. Also move all related tracing code into a new trace/
subdirectory.
No functional changes.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch makes KVM capable of using the XIVE interrupt controller
to provide the standard PAPR "XICS" style hypercalls. It is necessary
for proper operations when the host uses XIVE natively.
This has been lightly tested on an actual system, including PCI
pass-through with a TG3 device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Cleanup pr_xxx(), unsplit pr_xxx() strings, etc., fix build
failures by adding KVM_XIVE which depends on KVM_XICS and XIVE, and
adding empty stubs for the kvm_xive_xxx() routines, fixup subject,
integrate fixes from Paul for building PR=y HV=n]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The XIVE enablement patches included a change to set the LPES (Logical
Partitioning Environment Selector) bit (bit # 3) in LPCR (Logical Partitioning
Control Register) on POWER9 hosts. This bit sets external interrupts to guest
delivery mode, which uses SRR0/1. The host's EE interrupt handler is written to
expect HSRR0/1 (for earlier CPUs). This should be fine because XIVE is
configured not to deliver EEs to the host (Hypervisor Virtulization Interrupt is
used instead) so the EE handler should never be executed.
However a bug in interrupt controller code, hardware, or odd configuration of a
simulator could result in the host getting an EE incorrectly. Keeping the EE
delivery mode matching the host EE handler prevents strange crashes due to using
the wrong exception registers.
KVM will configure the LPCR to set LPES prior to running a guest so that EEs are
delivered to the guest using SRR0/1.
Fixes: 08a1e650cc ("powerpc: Fixup LPCR:PECE and HEIC setting on POWER9")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Massage change log to avoid referring to LPES0 which is now renamed LPES]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For CPUs present at boot each logical CPU acquires a reference to the
associated device node of the core. This happens in register_cpu() which
is called by topology_init(). The result of this is that we end up with
a reference held by each thread of the core. However, these references
are never freed if the CPU core is DLPAR removed.
This patch fixes the reference leaks by acquiring and releasing the references
in the CPU hotplug callbacks un/register_cpu_online(). With this patch symmetric
reference counting is observed with both CPUs present at boot, and those DLPAR
added after boot.
Fixes: f86e4718f2 ("driver/core: cpu: initialize of_node in cpu's device struture")
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Although most of these kprobes patches are powerpc specific, there's a couple
that touch generic code (with Acks). At the moment there's one conflict with
acme's tree, but it's not too bad. Still just in case some other conflicts show
up, we've put these in a topic branch so another tree could merge some or all of
it if necessary.
KPROBES_ON_FTRACE avoids much of the overhead of regular kprobes as it
eliminates the need for a trap, as well as the need to emulate or single-step
instructions.
Though OPTPROBES provides us with similar performance, we have limited
optprobes trampoline slots. As such, when asked to probe at a function
entry, default to using the ftrace infrastructure.
With:
# cd /sys/kernel/debug/tracing
# echo 'p _do_fork' > kprobe_events
before patch:
# cat ../kprobes/list
c0000000000daf08 k _do_fork+0x8 [DISABLED]
c000000000044fc0 k kretprobe_trampoline+0x0 [OPTIMIZED]
and after patch:
# cat ../kprobes/list
c0000000000d074c k _do_fork+0xc [DISABLED][FTRACE]
c0000000000412b0 k kretprobe_trampoline+0x0 [OPTIMIZED]
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
kprobe_lookup_name() is specific to the kprobe subsystem and may not always
return the function entry point (in a subsequent patch for KPROBES_ON_FTRACE).
For looking up function entry points, introduce a separate helper and use it
in optprobes.c
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Allow kprobes to be placed on ftrace _mcount() call sites. This optimization
avoids the use of a trap, by riding on ftrace infrastructure.
This depends on HAVE_DYNAMIC_FTRACE_WITH_REGS which depends on MPROFILE_KERNEL,
which is only currently enabled on powerpc64le with newer toolchains.
Based on the x86 code by Masami.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pass the real LR to the ftrace handler. This is needed for KPROBES_ON_FTRACE for
the pre handlers.
Also, with KPROBES_ON_FTRACE, the link register may be updated by the pre
handlers or by a registed kretprobe. Honor updated LR by restoring it from
pt_regs, rather than from the stack save area.
Live patch and function graph continue to work fine with this change.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Introduce __head_end to mark end of the early fixed sections and use it to
blacklist all exception handlers from kprobes.
mpe: We do not need to do anything special for relocatable kernels, where the
exception vectors are split from the main kernel, as the split vectors are
already excluded by the check for kernel_text_address().
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Move __head_end outside #ifdef 64-bit to unbreak the 32-bit build]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Along similar lines as commit 9326638cbe ("kprobes, x86: Use NOKPROBE_SYMBOL()
instead of __kprobes annotation"), convert __kprobes annotation to either
NOKPROBE_SYMBOL() or nokprobe_inline. The latter forces inlining, in which case
the caller needs to be added to NOKPROBE_SYMBOL().
Also:
- blacklist arch_deref_entry_point(), and
- convert a few regular inlines to nokprobe_inline in lib/sstep.c
A key benefit is the ability to detect such symbols as being
blacklisted. Before this patch:
$ cat /sys/kernel/debug/kprobes/blacklist | grep read_mem
$ perf probe read_mem
Failed to write event: Invalid argument
Error: Failed to add events.
$ dmesg | tail -1
[ 3736.112815] Could not insert probe at _text+10014968: -22
After patch:
$ cat /sys/kernel/debug/kprobes/blacklist | grep read_mem
0xc000000000072b50-0xc000000000072d20 read_mem
$ perf probe read_mem
read_mem is blacklisted function, skip it.
Added new events:
(null):(null) (on read_mem)
probe:read_mem (on read_mem)
You can now use it in all perf tools, such as:
perf record -e probe:read_mem -aR sleep 1
$ grep " read_mem" /proc/kallsyms
c000000000072b50 t read_mem
c0000000005f3b40 t read_mem
$ cat /sys/kernel/debug/kprobes/list
c0000000005f3b48 k read_mem+0x8 [DISABLED]
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Minor change log formatting, fix up some conflicts]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the stack setup and teardown code into ftrace_graph_caller(). This way, we
don't incur the cost of setting it up unless function graph is enabled for this
function.
Also, remove the extraneous LR restore code after the function graph stub. LR
has previously been restored and neither livepatch_handler() nor
ftrace_graph_caller() return back here.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Drop bad change to non-mprofile-kernel version of ftrace_graph_caller]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The idle workaround does not need to load PACATOC, and it does not
need to be called within a nested function that requires LR to be
saved.
Load the PACATOC at entry to the idle wakeup. It does not matter which
PACA this comes from, so it's okay to call before the workaround. Then
apply the workaround to get the right PACA.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If not all threads were in winkle, full state loss recovery is not
necessary and can be avoided. A previous patch removed this optimisation
due to some complexity with the implementation. Re-implement it by
counting the number of threads in winkle with the per-core idle state.
Only restore full state loss if all threads were in winkle.
This has a small window of false positives right before threads execute
winkle and just after they wake up, when the winkle count does not
reflect the true number of threads in winkle. This is not a significant
problem in comparison with even the minimum winkle duration. For
correctness, a false positive is not a problem (only false negatives
would be).
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When taking the core idle state lock, grab it immediately like a regular
lock, rather than adding more tests in there. Holding the lock keeps it
stable, so there is no need to do it whole holding the reservation.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In preparation for adding more bits to the core idle state word, move
the lock bit up, and unlock by flipping the lock bit rather than masking
off all but the thread bits.
Add branch hints for atomic operations while we're here.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ISA specifies power save wakeup due to a machine check exception can
cause a machine check interrupt (rather than the usual system reset
interrupt).
The machine check handler copes with this by doing low level machine
check recovery without restoring full state from idle, then queues up a
machine check event for logging, then directly executes the same idle
instruction it woke from. This minimises the work done before recovery
is performed.
The problem is that it requires machine specific instructions and
knowledge of the book3s idle code. Currently it only has code to handle
POWER8 idle, so POWER9 crashes when trying to execute the P8 idle
instructions which don't exist in ISAv3.0B.
cpu 0x0: Vector: e40 (Emulation Assist) at [c0000000008f3810]
pc: c000000000008380: machine_check_handle_early+0x130/0x2f0
lr: c00000000053a098: stop_loop+0x68/0xd0
sp: c0000000008f3a90
msr: 9000000000081001
current = 0xc0000000008a1080
paca = 0xc00000000ffd0000 softe: 0 irq_happened: 0x01
pid = 0, comm = swapper/0
Instead of going to sleep after recovery, do the usual idle wakeup and
state restoration by calling into the normal idle wakeup path. This
reuses the normal idle wakeup paths.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Mahesh J Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reduces the number of nops for POWER8.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The POWER8 idle code has a neat trick of programming the power on engine
to restore a low bit into HSPRG0, so idle wakeup code can test and see
if it has been programmed this way and therefore lost all state. Restore
time can be reduced if winkle has not been reached.
However this messes with our r13 PACA pointer, and requires HSPRG0 to be
written to. It also optimizes the slowest and most uncommon case at the
expense of another SPR write in the common nap state wakeup.
Remove this complexity and assume winkle sleeps always require a state
restore. This speedup could be made entirely contained within the winkle
idle code by counting per-core winkles and setting a thread bitmap when
all have gone to winkle.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
No functional change.
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The system reset idle handler system_reset_idle_common is relocated, so
relocation is not required to branch to kvm_start_guest. The superfluous
relocation does not result in incorrect code, but it does not compile
outside of exception-64s.S (with fixed section definitions).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In all cases we know which BAR it is. Passing it in means that arch code
(or generic code; watch this space) won't have to go looking for it again.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On kprobe handler re-entry, try to emulate the instruction rather than single
stepping always.
Acked-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Factor out code to emulate instruction into a try_to_emulate()
helper function. This makes no functional changes.
Acked-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With ABIv2, we offset 8 bytes into a function to get at the local entry
point.
mpe: NB this function is currently not called, the change to generic code to
call it is being merged via the tip tree.
Acked-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit 239aeba764 ("perf powerpc: Fix kprobe and kretprobe handling with
kallsyms on ppc64le") changed how we use the offset field in struct kprobe on
ABIv2. perf now offsets from the global entry point if an offset is specified
and otherwise chooses the local entry point.
Fix the same in kernel for kprobe API users. We do this by extending
kprobe_lookup_name() to accept an additional parameter to indicate the offset
specified with the kprobe registration. If offset is 0, we return the local
function entry and return the global entry point otherwise.
With:
# cd /sys/kernel/debug/tracing/
# echo "p _do_fork" >> kprobe_events
# echo "p _do_fork+0x10" >> kprobe_events
before this patch:
# cat ../kprobes/list
c0000000000d0748 k _do_fork+0x8 [DISABLED]
c0000000000d0758 k _do_fork+0x18 [DISABLED]
c0000000000412b0 k kretprobe_trampoline+0x0 [OPTIMIZED]
and after:
# cat ../kprobes/list
c0000000000d04c8 k _do_fork+0x8 [DISABLED]
c0000000000d04d0 k _do_fork+0x10 [DISABLED]
c0000000000412b0 k kretprobe_trampoline+0x0 [OPTIMIZED]
Acked-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The macro is now pretty long and ugly on powerpc. In the light of further
changes needed here, convert it to a __weak variant to be over-ridden with a
nicer looking function.
Suggested-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This reworks helpers for checking TCE update parameters in way they
can be used in KVM.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Override pcibios_default_alignment() to set default alignment to PAGE_SIZE
for all PCI devices on PowerNV platform. Thus sub-page BARs would not
share a page and could be mapped into guest when VFIO passthrough them.
Signed-off-by: Yongji Xie <elohimes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The TLB flush for radix first flushes TLB for radix configuration,
then flushes for hash configuration. The second flush is unnecessary
but does not affect correctness.
Fixes: 1a472c9dba ("powerpc/mm/radix: Add tlbflush routines")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The XIVE enablement patches included a change to set the LPES (Logical
Partitioning Environment Selector) bit (bit # 3) in LPCR (Logical Partitioning
Control Register) on POWER9 hosts. This bit sets external interrupts to guest
delivery mode, which uses SRR0/1. The host's EE interrupt handler is written to
expect HSRR0/1 (for earlier CPUs). This should be fine because XIVE is
configured not to deliver EEs to the host (Hypervisor Virtulization Interrupt is
used instead) so the EE handler should never be executed.
However a bug in interrupt controller code, hardware, or odd configuration of a
simulator could result in the host getting an EE incorrectly. Keeping the EE
delivery mode matching the host EE handler prevents strange crashes due to using
the wrong exception registers.
KVM will configure the LPCR to set LPES prior to running a guest so that EEs are
delivered to the guest using SRR0/1.
Fixes: 08a1e650cc ("powerpc: Fixup LPCR:PECE and HEIC setting on POWER9")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Massage change log to avoid referring to LPES0 which is now renamed LPES]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Prior to commit 2337d20728 ("powerpc/64: CONFIG_RELOCATABLE support for hmi
interrupts"), the branch from hmi_exception_early() to hmi_exception_realmode()
was just a bl hmi_exception_realmode, which the linker would turn into a bl to
the local entry point of hmi_exception_realmode. This was broken when
CONFIG_RELOCATABLE=y because hmi_exception_realmode() is not in the low part of
the kernel text that is copied down to 0x0.
But in fixing that, we added a new bug on little endian kernels. Because the
branch is now a bctrl when CONFIG_RELOCATABLE=y, we branch to the global entry
point of hmi_exception_realmode(). The global entry point must be called with
r12 containing the address of hmi_exception_realmode(), because it uses that
value to calculate the TOC value (r2).
This may manifest as a checkstop, because we take a junk value from r12 which
came from HSRR1, add a small constant to it and then use that as the TOC
pointer. The HSRR1 value will have 0x9 as the top nibble, which puts it above
RAM and somewhere in MMIO space.
Fix it by changing the BRANCH_LINK_TO_FAR() macro to always use r12 to load the
label we're branching to. This means r12 will be setup correctly on LE, fixing
this bug, and r12 is also volatile across function calls on BE so it's a good
choice anyway.
Fixes: 2337d20728 ("powerpc/64: CONFIG_RELOCATABLE support for hmi interrupts")
Reported-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If we set a kprobe on a 'stdu' instruction on powerpc64, we see a kernel
OOPS:
Bad kernel stack pointer cd93c840 at c000000000009868
Oops: Bad kernel stack pointer, sig: 6 [#1]
...
GPR00: c000001fcd93cb30 00000000cd93c840 c0000000015c5e00 00000000cd93c840
...
NIP [c000000000009868] resume_kernel+0x2c/0x58
LR [c000000000006208] program_check_common+0x108/0x180
On a 64-bit system when the user probes on a 'stdu' instruction, the kernel does
not emulate actual store in emulate_step() because it may corrupt the exception
frame. So the kernel does the actual store operation in exception return code
i.e. resume_kernel().
resume_kernel() loads the saved stack pointer from memory using lwz, which only
loads the low 32-bits of the address, causing the kernel crash.
Fix this by loading the 64-bit value instead.
Fixes: be96f63375 ("powerpc: Split out instruction analysis part of emulate_step()")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Ananth N Mavinakayanahalli <ananth@linux.vnet.ibm.com>
[mpe: Change log massage, add stable tag]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Init task invokes smp_ops->setup_cpu() from smp_cpus_done(). Init task can
run on any online CPU at this point, but the setup_cpu() callback requires
to be invoked on the boot CPU. This is achieved by temporarily setting the
affinity of the calling user space thread to the requested CPU and reset it
to the original affinity afterwards.
That's racy vs. CPU hotplug and concurrent affinity settings for that
thread resulting in code executing on the wrong CPU and overwriting the
new affinity setting.
That's actually not a problem in this context as neither CPU hotplug nor
affinity settings can happen, but the access to task_struct::cpus_allowed
is about to restricted.
Replace it with a call to work_on_cpu_safe() which achieves the same result.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/20170412201042.518053336@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In preparation for making the clockevents core NTP correction aware,
all clockevent device drivers must set ->min_delta_ticks and
->max_delta_ticks rather than ->min_delta_ns and ->max_delta_ns: a
clockevent device's rate is going to change dynamically and thus, the
ratio of ns to ticks ceases to stay invariant.
Make the powerpc arch's clockevent driver initialize these fields properly.
This patch alone doesn't introduce any change in functionality as the
clockevents core still looks exclusively at the (untouched) ->min_delta_ns
and ->max_delta_ns. As soon as this has changed, a followup patch will
purge the initialization of ->min_delta_ns and ->max_delta_ns from this
driver.
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Oliver O'Halloran <oohall@gmail.com>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
POWER9 changes requirements and adds new instructions for
synchronization.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change the doorbell callers to know about their msgsnd addressing,
rather than have them set a per-cpu target data tag at boot that gets
sent to the cause_ipi functions. The data is only used for doorbell IPI
functions, no other IPI types, so it makes sense to keep that detail
local to doorbell.
Have the platform code understand doorbell IPIs, rather than the
interrupt controller code understand them. Platform code can look at
capabilities it has available and decide which to use.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add the bit definition and use it in facility_unavailable_exception() so we can
intelligently report the cause if we take a fault for SCV. This doesn't actually
enable SCV.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Drop whitespace changes to the existing entries, flush out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently sys_mmap() and sys_mmap2() (32-bit only), are not visible to the
syscall tracing machinery. This means users are not able to see the execution of
mmap() syscalls using the syscall tracer.
Fix that by using SYSCALL_DEFINE6 for sys_mmap() and sys_mmap2() so that the
meta-data associated with these syscalls is visible to the syscall tracer.
A side-effect of this change is that the return type has changed from unsigned
long to long. However this should have no effect, the only code in the kernel
which uses the result of these syscalls is in the syscall return path, which is
written in asm and treats the result as unsigned regardless.
Example output:
cat-3399 [001] .... 196.542410: sys_mmap(addr: 7fff922a0000, len: 20000, prot: 3, flags: 812, fd: 3, offset: 1b0000)
cat-3399 [001] .... 196.542443: sys_mmap -> 0x7fff922a0000
cat-3399 [001] .... 196.542668: sys_munmap(addr: 7fff922c0000, len: 6d2c)
cat-3399 [001] .... 196.542677: sys_munmap -> 0x0
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Massage change log, add detail on return type change]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Recently in commit f6eedbba7a ("powerpc/mm/hash: Increase VA range to 128TB"),
we increased H_PGD_INDEX_SIZE to 15 when we're building with 64K pages. This
makes it larger than RADIX_PGD_INDEX_SIZE (13), which means the logic to
calculate MAX_PGD_INDEX_SIZE in book3s/64/pgtable.h is wrong.
The end result is that the PGD (Page Global Directory, ie top level page table)
of the kernel (aka. swapper_pg_dir), is too small.
This generally doesn't lead to a crash, as we don't use the full range in normal
operation. However if we try to dump the kernel pagetables we can trigger a
crash because we walk off the end of the pgd into other memory and eventually
try to dereference something bogus:
$ cat /sys/kernel/debug/kernel_pagetables
Unable to handle kernel paging request for data at address 0xe8fece0000000000
Faulting instruction address: 0xc000000000072314
cpu 0xc: Vector: 380 (Data SLB Access) at [c0000000daa13890]
pc: c000000000072314: ptdump_show+0x164/0x430
lr: c000000000072550: ptdump_show+0x3a0/0x430
dar: e802cf0000000000
seq_read+0xf8/0x560
full_proxy_read+0x84/0xc0
__vfs_read+0x6c/0x1d0
vfs_read+0xbc/0x1b0
SyS_read+0x6c/0x110
system_call+0x38/0xfc
The root cause is that MAX_PGD_INDEX_SIZE isn't actually computed to be
the max of H_PGD_INDEX_SIZE or RADIX_PGD_INDEX_SIZE. To fix that move
the calculation into asm-offsets.c where we can do it easily using
max().
Fixes: f6eedbba7a ("powerpc/mm/hash: Increase VA range to 128TB")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This merges the arch part of the XIVE support, leaving the final commit
with the KVM specific pieces dangling on the branch for Paul to merge
via the kvm-ppc tree.
POWER9 DD1.0 hardware has a bug where the SPRs of a thread waking up
from stop 0,1,2 with ESL=1 can endup being misplaced in the core. Thus
the HSPRG0 of a thread waking up from can contain the paca pointer of
its sibling.
This patch implements a context recovery framework within threads of a
core, by provisioning space in paca_struct for saving every sibling
threads's paca pointers. Basically, we should be able to arrive at the
right paca pointer from any of the thread's existing paca pointer.
At bootup, during powernv idle-init, we save the paca address of every
CPU in each one its siblings paca_struct in the slot corresponding to
this CPU's index in the core.
On wakeup from a stop, the thread will determine its index in the core
from the TIR register and recover its PACA pointer by indexing into
the correct slot in the provisioned space in the current PACA.
Furthermore, ensure that the NVGPRs are restored from the stack on the
way out by setting the NAPSTATELOST in paca.
[Changelog written with inputs from svaidy@linux.vnet.ibm.com]
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Call it a bug]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These files don't seem to have any need for asm/debug.h, now that all it
includes are the debugger hooks and breakpoint definitions.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc_debugfs_root is the dentry representing the root of the
"powerpc" directory tree in debugfs.
Currently it sits in asm/debug.h, a long with some other things that
have "debug" in the name, but are otherwise unrelated.
Pull it out into a separate header, which also includes linux/debugfs.h,
and convert all the users to include debugfs.h instead of debug.h.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We need to set LPES in order for normal external interrupts (0x500)
to be directed to the guest while running in guest state.
We also need HEIC set to prevent them to be sent to the host while
in host state.
With XIVE the host never gets one of these and wouldn't know how to
handle it. All host external interrupts come in via the new
hypervisor virtualization interrupts vector.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some powerpc platforms use this to move IRQs away from a CPU being
unplugged. This function has several bugs such as not taking the right
locks or failing to NULL check pointers.
There's a new generic function doing exactly the same thing without all
the bugs, so let's use it instead.
mpe: The obvious place for the select of GENERIC_IRQ_MIGRATION is on
HOTPLUG_CPU, but that doesn't work. On some configs PM_SLEEP_SMP will
select HOTPLUG_CPU even though its dependencies are not met, which means
the select of GENERIC_IRQ_MIGRATION doesn't happen. That leads to the
build breaking. Fix it by moving the select of GENERIC_IRQ_MIGRATION to
SMP.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some platforms (will) need to perform allocations before bringing
a new CPU online. Doing it from smp_ops->setup_cpu is the wrong
thing to do:
- It has no useful failure path (too late)
- Calling any allocator will enable interrupts prematurely
causing problems with large decrementer among others
Instead, add a new callback that is called from __cpu_up (so from
the context trying to online the new CPU) at a point where we
can safely allocate and handle failures.
This will be used by XIVE support.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the kernel is compiled to use 64bit ABIv2 the _GLOBAL() macro does
not include a global entry point. A function's global entry point is
used when the function is called from a different TOC context and in the
kernel this typically means a call from a module into the vmlinux (or
vice-versa).
There are a few exported asm functions declared with _GLOBAL() and
calling them from a module will likely crash the kernel since any TOC
relative load will yield garbage.
flush_icache_range() and flush_dcache_range() are both exported to
modules, and use the TOC, so must use _GLOBAL_TOC().
Fixes: 721aeaa9fd ("powerpc: Build little endian ppc64 kernel with ABIv2")
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the past, there was only one load-with-reservation instruction,
lwarx, and if a program attempted a lwarx on a misaligned address, it
would take an alignment interrupt and the kernel handler would emulate
it as though it was lwzx, which was not really correct, but benign since
it is loading the right amount of data, and the lwarx should be paired
with a stwcx. to the same address, which would also cause an alignment
interrupt which would result in a SIGBUS being delivered to the process.
We now have 5 different sizes of load-with-reservation instruction. Of
those, lharx and ldarx cause an immediate SIGBUS by luck since their
entries in aligninfo[] overlap instructions which were not fixed up, but
lqarx overlaps with lhz and will be emulated as such. lbarx can never
generate an alignment interrupt since it only operates on 1 byte.
To straighten this out and fix the lqarx case, this adds code to detect
the l[hwdq]arx instructions and return without fixing them up, resulting
in a SIGBUS being delivered to the process.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When booting very large systems with a large initrd, we run out of
space early in boot for either RTAS or the flattened device tree (FDT).
Boot fails with messages like:
Could not allocate memory for RTAS
or
No memory for flatten_device_tree (no room)
Increasing the minimum RMA size to 512MB fixes the problem. This
should not have an impact on smaller LPARs (with 256MB memory),
as the firmware will cap the RMA to the memory assigned to the LPAR.
Fix is based on input/discussions with Michael Ellerman. Thanks to
Praveen K. Pandey for testing on a large system.
Reported-by: Praveen K. Pandey <preveen.pandey@in.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The kbuild test robot reported this build failure on a number
of architectures:
> make.cross ARCH=arm
> lib/lib.a(bug.o): In function `find_bug':
> >> lib/bug.c:135: undefined reference to `__start___bug_table'
> >> lib/bug.c:135: undefined reference to `__stop___bug_table'
Caused by:
19d436268d ("debug: Add _ONCE() logic to report_bug()")
Which moved the BUG_TABLE from RO_DATA_SECTION() to RW_DATA_SECTION(),
but a number of architectures don't use RW_DATA_SECTION(), so they
ended up with no __bug_table[] ...
Ideally all those would use RW_DATA_SECTION() in their linker scripts,
but that's for another day.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kbuild test robot <fengguang.wu@intel.com>
Cc: kbuild-all@01.org
Cc: tipbuild@zytor.com
Link: http://lkml.kernel.org/r/20170330154927.o6qmgfp4bdhrajbm@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For an MCE (Machine Check Exception) that hits while in user mode
MSR(PR=1), print the task info to the console MCE error log. This may
help to identify an application that triggered the MCE.
After this patch the MCE console looks like:
Severe Machine check interrupt [Recovered]
NIP: [0000000010039778] PID: 762 Comm: ebizzy
Initiator: CPU
Error type: SLB [Multihit]
Effective address: 0000000010039778
Severe Machine check interrupt [Not recovered]
NIP: [0000000010039778] PID: 763 Comm: ebizzy
Initiator: CPU
Error type: UE [Page table walk ifetch]
Effective address: 0000000010039778
ebizzy[763]: unhandled signal 7 at 0000000010039778 nip 0000000010039778 lr 0000000010001b44 code 30004
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For D-side errors we print the load/store address that caused the
machine check as 'Effective address'. But the instruction that may have
caused the machine check can also be helpful, so in addition to printing
the NIP, also print the kernel function name as well.
After this patch the MCE console log would look like:
Severe Machine check interrupt [Recovered]
NIP [d00000001bc70194]: init_module+0x194/0x2b0 [bork_kernel]
Initiator: CPU
Error type: SLB [Parity]
Effective address: d000000026de0000
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Not all user space application is ready to handle wide addresses. It's
known that at least some JIT compilers use higher bits in pointers to
encode their information. It collides with valid pointers with 512TB
addresses and leads to crashes.
To mitigate this, we are not going to allocate virtual address space
above 128TB by default.
But userspace can ask for allocation from full address space by
specifying hint address (with or without MAP_FIXED) above 128TB.
If hint address set above 128TB, but MAP_FIXED is not specified, we try
to look for unmapped area by specified address. If it's already
occupied, we look for unmapped area in *full* address space, rather than
from 128TB window.
This approach helps to easily make application's memory allocator aware
about large address space without manually tracking allocated virtual
address space.
This is going to be a per mmap decision. ie, we can have some mmaps with
larger addresses and other that do not.
A sample memory layout looks like:
10000000-10010000 r-xp 00000000 fc:00 9057045 /home/max_addr_512TB
10010000-10020000 r--p 00000000 fc:00 9057045 /home/max_addr_512TB
10020000-10030000 rw-p 00010000 fc:00 9057045 /home/max_addr_512TB
10029630000-10029660000 rw-p 00000000 00:00 0 [heap]
7fff834a0000-7fff834b0000 rw-p 00000000 00:00 0
7fff834b0000-7fff83670000 r-xp 00000000 fc:00 9177190 /lib/powerpc64le-linux-gnu/libc-2.23.so
7fff83670000-7fff83680000 r--p 001b0000 fc:00 9177190 /lib/powerpc64le-linux-gnu/libc-2.23.so
7fff83680000-7fff83690000 rw-p 001c0000 fc:00 9177190 /lib/powerpc64le-linux-gnu/libc-2.23.so
7fff83690000-7fff836a0000 rw-p 00000000 00:00 0
7fff836a0000-7fff836c0000 r-xp 00000000 00:00 0 [vdso]
7fff836c0000-7fff83700000 r-xp 00000000 fc:00 9177193 /lib/powerpc64le-linux-gnu/ld-2.23.so
7fff83700000-7fff83710000 r--p 00030000 fc:00 9177193 /lib/powerpc64le-linux-gnu/ld-2.23.so
7fff83710000-7fff83720000 rw-p 00040000 fc:00 9177193 /lib/powerpc64le-linux-gnu/ld-2.23.so
7fffdccf0000-7fffdcd20000 rw-p 00000000 00:00 0 [stack]
1000000000000-1000000010000 rw-p 00000000 00:00 0
1ffff83710000-1ffff83720000 rw-p 00000000 00:00 0
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We optmize the slice page size array copy to paca by copying only the
range based on addr_limit. This will require us to not look at page size
array beyond addr_limit in PACA on slb fault. To enable that copy task
size to paca which will be used during slb fault.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Rename from task_size to addr_limit, consolidate #ifdefs]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the followup patch, we will increase the slice array size to handle
512TB range, but will limit the max addr to 128TB. Avoid doing
unnecessary computation and avoid doing slice mask related operation
above address limit.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We also update the function arg to struct mm_struct. Move this so that function
finds the definition of struct mm_struct. No functional change in this patch.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, the area to preserve boot memory is reserved at the top of
RAM. This leaves fadump vulnerable to memory hot-remove operations. As
memory for fadump has to be reserved early in the boot process, fadump
can't be registered after a memory hot-remove operation. Though this
problem can't be eleminated completely, the impact can be minimized by
reserving memory at an offset closer to bottom of the RAM. The offset
for fadump memory reservation can be any value greater than fadump boot
memory size.
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
So far iommu_table obejcts were only used in virtual mode and had
a single owner. We are going to change this by implementing in-kernel
acceleration of DMA mapping requests. The proposed acceleration
will handle requests in real mode and KVM will keep references to tables.
This adds a kref to iommu_table and defines new helpers to update it.
This replaces iommu_free_table() with iommu_tce_table_put() and makes
iommu_free_table() static. iommu_tce_table_get() is not used in this patch
but it will be in the following patch.
Since this touches prototypes, this also removes @node_name parameter as
it has never been really useful on powernv and carrying it for
the pseries platform code to iommu_free_table() seems to be quite
useless as well.
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the moment iommu_table can be disposed by either calling
iommu_table_free() directly or it_ops::free(); the only implementation
of free() is in IODA2 - pnv_ioda2_table_free() - and it calls
iommu_table_free() anyway.
As we are going to have reference counting on tables, we need an unified
way of disposing tables.
This moves it_ops::free() call into iommu_free_table() and makes use
of the latter. The free() callback now handles only platform-specific
data.
As from now on the iommu_free_table() calls it_ops->free(), we need
to have it_ops initialized before calling iommu_free_table() so this
moves this initialization in pnv_pci_ioda2_create_table().
This should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In real mode, TCE tables are invalidated using special
cache-inhibited store instructions which are not available in
virtual mode
This defines and implements exchange_rm() callback. This does not
define set_rm/clear_rm/flush_rm callbacks as there is no user for those -
exchange/exchange_rm are only to be used by KVM for VFIO.
The exchange_rm callback is defined for IODA1/IODA2 powernv platforms.
This replaces list_for_each_entry_rcu with its lockless version as
from now on pnv_pci_ioda2_tce_invalidate() can be called in
the real mode too.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On Power8 & Power9 the early CPU inititialisation in __init_HFSCR()
turns on HFSCR[TM] (Hypervisor Facility Status and Control Register
[Transactional Memory]), but that doesn't take into account that TM
might be disabled by CPU features, or disabled by the kernel being built
with CONFIG_PPC_TRANSACTIONAL_MEM=n.
So later in boot, when we have setup the CPU features, clear HSCR[TM] if
the TM CPU feature has been disabled. We use CPU_FTR_TM_COMP to account
for the CONFIG_PPC_TRANSACTIONAL_MEM=n case.
Without this a KVM guest might try use TM, even if told not to, and
cause an oops in the host kernel. Typically the oops is seen in
__kvmppc_vcore_entry() and may or may not be fatal to the host, but is
always bad news.
In practice all shipping CPU revisions do support TM, and all host
kernels we are aware of build with TM support enabled, so no one should
actually be able to hit this in the wild.
Fixes: 2a3563b023 ("powerpc: Setup in HFSCR for POWER8")
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
[mpe: Rewrite change log with input from Sam, add Fixes/stable]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For the current task, the kernel stack would only tell the last time the
process was rescheduled, if ever. Use the current stack pointer for the
current task.
Otherwise, every once in a while, the stacktrace printed when reading
/proc/self/stack would look like the process is running in userspace,
while it's not, which some may consider as a bug.
This is also consistent with some other architectures, like x86 and arm,
at least.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cpu_ready_for_interrupts() is called after feature patching, so there's
no need to use early_cpu_has_feature().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER8 uses bit 36 in SRR1 like POWER9 for i-side machine checks, and
contains several conditions for link timeouts that are not currently
handled.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the handling (corrective action) of machine checks to the table
based evaluation.
This changes P7 and P8 ERAT flushing from using SLB flush to using ERAT
flush.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Have machine types define i-side and d-side tables to describe their
machine check encodings, and match entries to evaluate (for reporting)
machine checks.
Functionality is mostly unchanged (tested with a userspace harness), but
it does make a change in that it no longer records DAR as the effective
address for those errors where it is specified to be invalid (which is a
reporting change only).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the flush function introduced with the POWER9 machine check handler
for POWER7 and 8, rather than open coding it multiple times in callers.
There is a specific ERAT flush type introduced for POWER9, but the
POWER7-8 ERAT errors continue to do SLB flushing (which also flushes
ERAT), so as not to introduce functional changes with this cleanup
patch.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Print the faulting address of the machine check that may help with
debugging. The effective address reported can be a target memory address
rather than the faulting instruction address.
Fix up a dangling bracket while here.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The symbols exported for use by MOL/rtlinux aren't getting CRCs and I
was about to fix that. But MOL is dead upstream, and the latest work on
it was to make it use KVM instead of its own kernel module. So remove
them instead.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We concluded there may be a window where the idle wakeup code could get
to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the
hardware may set SRR1[46:47] to 01b (no state loss) which would result
in the wakeup code failing to restore non-volatile GPRs.
I was not able to trigger this condition with trivial tests on real
hardware or simulator, but the ISA (at least 2.07) seems to allow for
it, and Gautham says that it can happen if there is an exception pending
when the sleep/winkle instruction is executed.
Fixes: 1706567117 ("powerpc/kvm: make hypervisor state restore a function")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sparse emits a warning: symbol 'prepare_ftrace_return' was not
declared. Should it be static? prepare_ftrace_return() is called from
assembler and should not be static.
Add a prototype for it to asm-prototypes.h and include that in ftrace.c.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Sparse emits two symbol not declared warnings for swsusp.c. The two
functions, save_processor_state() and restore_processor_state() are
declared already in suspend.h, so include it.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix an assembler error when the THREAD_SIZE is greater than 16k.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add POWER9 machine check handler. There are several new types of errors
added, so logging messages for those are also added.
This doesn't attempt to reuse any of the P7/8 defines or functions,
because that becomes too complex. The better option in future is to use
a table driven approach.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently severity and initiator are always set to MCE_SEV_ERROR_SYNC and
MCE_INITIATOR_CPU in the core mce code. Allow them to be set by the
machine specific mce handlers.
No functional change for existing handlers.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add the TIF_PATCH_PENDING thread flag to enable the new livepatch
per-task consistency model for powerpc. The bit getting set indicates
the thread has a pending patch which needs to be applied when the thread
exits the kernel.
The bit is included in the _TIF_USER_WORK_MASK macro so that
do_notify_resume() and klp_update_patch_state() get called when the bit
is set.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Miroslav Benes <mbenes@suse.cz>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Similar to the pstore_info read() callback, there were too many arguments.
This switches to the new struct pstore_record pointer instead. This adds
"reason" and "part" to the record structure as well.
Signed-off-by: Kees Cook <keescook@chromium.org>
The argument list for the pstore_read() interface is unwieldy. This changes
passes the new struct pstore_record instead. The erst backend was already
doing something similar internally.
Signed-off-by: Kees Cook <keescook@chromium.org>
Five fairly small fixes for things that went in this cycle.
A fairly large patch to rework the CAS logic on Power9, necessitated by a late
change to the firmware API, and we can't boot without it.
Three fixes going to stable, allowing more instructions to be emulated on LE,
fixing a boot crash on 32-bit Freescale BookE machines, and the OPAL XICS
workaround.
And a patch from me to sort the selects under CONFIG PPC. Annoying churn, but
worth it in the long run, and best for it to go in now to avoid conflicts.
Thanks to:
Alexey Kardashevskiy, Anton Blanchard, Balbir Singh, Gautham R. Shenoy,
Laurentiu Tudor, Nicholas Piggin, Paul Mackerras, Ravi Bangoria, Sachin Sant,
Shile Zhang, Suraj Jitindar Singh.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SxON
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Five fairly small fixes for things that went in this cycle.
A fairly large patch to rework the CAS logic on Power9, necessitated
by a late change to the firmware API, and we can't boot without it.
Three fixes going to stable, allowing more instructions to be emulated
on LE, fixing a boot crash on 32-bit Freescale BookE machines, and the
OPAL XICS workaround.
And a patch from me to sort the selects under CONFIG PPC. Annoying
churn, but worth it in the long run, and best for it to go in now to
avoid conflicts.
Thanks to:
Alexey Kardashevskiy, Anton Blanchard, Balbir Singh, Gautham R.
Shenoy, Laurentiu Tudor, Nicholas Piggin, Paul Mackerras, Ravi
Bangoria, Sachin Sant, Shile Zhang, Suraj Jitindar Singh"
* tag 'powerpc-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Sort the selects under CONFIG_PPC
powerpc/64: Fix L1D cache shape vector reporting L1I values
powerpc/64: Avoid panic during boot due to divide by zero in init_cache_info()
powerpc: Update to new option-vector-5 format for CAS
powerpc: Parse the command line before calling CAS
powerpc/xics: Work around limitations of OPAL XICS priority handling
powerpc/64: Fix checksum folding in csum_add()
powerpc/powernv: Fix opal tracepoints with JUMP_LABEL=n
powerpc/booke: Fix boot crash due to null hugepd
powerpc: Fix compiling a BE kernel with a powerpc64le toolchain
selftest/powerpc: Fix false failures for skipped tests
powerpc/powernv: Fix bug due to labeling ambiguity in power_enter_stop
powerpc/64: Invalidate process table caching after setting process table
powerpc: emulate_step() tests for load/store instructions
powerpc: Emulation support for load/store instructions on LE
I see a panic in early boot when building with a recent gcc toolchain.
The issue is a divide by zero, which is undefined. Older toolchains
let us get away with it:
int foo(int a) { return a / 0; }
foo:
li 9,0
divw 3,3,9
extsw 3,3
blr
But newer ones catch it:
foo:
trap
Add a check to avoid the divide by zero.
Fixes: e2827fe5c1 ("powerpc/64: Clean up ppc64_caches using a struct per cache")
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9 the ibm,client-architecture-support (CAS) negotiation process
has been updated to change how the host to guest negotiation is done for
the new hash/radix mmu as well as the nest mmu, process tables and guest
translation shootdown (GTSE).
This is documented in the unreleased PAPR ACR "CAS option vector
additions for P9".
The host tells the guest which options it supports in
ibm,arch-vec-5-platform-support. The guest then chooses a subset of these
to request in the CAS call and these are agreed to in the
ibm,architecture-vec-5 property of the chosen node.
Thus we read ibm,arch-vec-5-platform-support and make our selection before
calling CAS. We then parse the ibm,architecture-vec-5 property of the
chosen node to check whether we should run as hash or radix.
ibm,arch-vec-5-platform-support format:
index value pairs: <index, val> ... <index, val>
index: Option vector 5 byte number
val: Some representation of supported values
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
[mpe: Don't print about unknown options, be consistent with OV5_FEAT]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On POWER9 the hypervisor requires the guest to decide whether it would
like to use a hash or radix mmu model at the time it calls
ibm,client-architecture-support (CAS) based on what the hypervisor has
said it's allowed to do. It is possible to disable radix by passing
"disable_radix" on the command line. The next patch will add support for
the new CAS format, thus we need to parse the command line before calling
CAS so we can correctly select which mmu we would like to use.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 09206b600c ("powernv: Pass PSSCR value and mask to
power9_idle_stop") added additional code in power_enter_stop() to
distinguish between stop requests whose PSSCR had ESL=EC=1 from those
which did not. When ESL=EC=1, we do a forward-jump to a location
labelled by "1", which had the code to handle the ESL=EC=1 case.
Unfortunately just a couple of instructions before this label, is the
macro IDLE_STATE_ENTER_SEQ() which also has a label "1" in its
expansion.
As a result, the current code can result in directly executing stop
instruction for deep stop requests with PSSCR ESL=EC=1, without saving
the hypervisor state.
Fix this BUG by labeling the location that handles ESL=EC=1 case with
a more descriptive label ".Lhandle_esl_ec_set" (local label suggestion
a la .Lxx from Anton Blanchard).
While at it, rename the label "2" labelling the location of the code
handling entry into deep stop states with ".Lhandle_deep_stop".
For a good measure, change the label in IDLE_STATE_ENTER_SEQ() macro
to an not-so commonly used value in order to avoid similar mishaps in
the future.
Fixes: 09206b600c ("powernv: Pass PSSCR value and mask to power9_idle_stop")
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Introduce a trivial, mostly empty <linux/sched/cputime.h> header
to prepare for the moving of cputime functionality out of sched.h.
Update all code that relies on these facilities.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Update code that relied on sched.h including various MM types for them.
This will allow us to remove the <linux/mm_types.h> include from <linux/sched.h>.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task_stack.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task_stack.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/task.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/debug.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/debug.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to move softlockup APIs out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
<linux/nmi.h> already includes <linux/sched.h>.
Include the <linux/nmi.h> header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/clock.h> out of <linux/sched.h>, which
will have to be picked up from other headers and .c files.
Create a trivial placeholder <linux/sched/clock.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/topology.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/topology.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
So the original intention of tsk_cpus_allowed() was to 'future-proof'
the field - but it's pretty ineffectual at that, because half of
the code uses ->cpus_allowed directly ...
Also, the wrapper makes the code longer than the original expression!
So just get rid of it. This also shrinks <linux/sched.h> a bit.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Highlights include:
- An update of the disassembly code used by xmon to the latest versions in
binutils. We've received permission from all the authors of the relevant
binutils changes to relicense their changes to the relevant files from GPLv3
to GPLv2, for inclusion in Linux. Thanks to Peter Bergner for doing the leg
work to get permission from everyone.
- Addition of the "architected" Power9 CPU table entry, allowing us to boot
in Power9 architected mode under a hypervisor.
- Updates to the Power9 PMU code.
- Implementation of clear_bit_unlock_is_negative_byte() to optimise
unlock_page().
- Freescale updates from Scott: "Highlights include 8xx breakpoints and perf,
t1042rdb display support, and board updates."
Thanks to:
Al Viro, Andrew Donnellan, Aneesh Kumar K.V, Balbir Singh, Douglas Miller,
Frédéric Weisbecker, Gavin Shan, Madhavan Srinivasan, Michael Roth, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Peter Bergner, Paul E. McKenney,
Rashmica Gupta, Russell Currey, Sahil Mehta, Stewart Smith.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rspd
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"Highlights include:
- an update of the disassembly code used by xmon to the latest
versions in binutils. We've received permission from all the
authors of the relevant binutils changes to relicense their changes
to the relevant files from GPLv3 to GPLv2, for inclusion in Linux.
Thanks to Peter Bergner for doing the leg work to get permission
from everyone.
- addition of the "architected" Power9 CPU table entry, allowing us
to boot in Power9 architected mode under a hypervisor.
- updates to the Power9 PMU code.
- implementation of clear_bit_unlock_is_negative_byte() to optimise
unlock_page().
- Freescale updates from Scott: "Highlights include 8xx breakpoints
and perf, t1042rdb display support, and board updates."
Thanks to:
Al Viro, Andrew Donnellan, Aneesh Kumar K.V, Balbir Singh, Douglas
Miller, Frédéric Weisbecker, Gavin Shan, Madhavan Srinivasan,
Michael Roth, Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Peter
Bergner, Paul E. McKenney, Rashmica Gupta, Russell Currey, Sahil
Mehta, Stewart Smith"
* tag 'powerpc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (48 commits)
powerpc: Remove leftover cputime_to_nsecs call causing build error
powerpc/mm/hash: Always clear UPRT and Host Radix bits when setting up CPU
powerpc/optprobes: Fix TOC handling in optprobes trampoline
powerpc/pseries: Advertise Hot Plug Event support to firmware
cxl: fix nested locking hang during EEH hotplug
powerpc/xmon: Dump memory in CPU endian format
powerpc/pseries: Revert 'Auto-online hotplugged memory'
powerpc/powernv: Make PCI non-optional
powerpc/64: Implement clear_bit_unlock_is_negative_byte()
powerpc/powernv: Remove unused variable in pnv_pci_sriov_disable()
powerpc/kernel: Remove error message in pcibios_setup_phb_resources()
powerpc/mm: Fix typo in set_pte_at()
pci/hotplug/pnv-php: Disable MSI and PCI device properly
pci/hotplug/pnv-php: Disable surprise hotplug capability on conflicts
pci/hotplug/pnv-php: Remove WARN_ON() in pnv_php_put_slot()
powerpc: Add POWER9 architected mode to cputable
powerpc/perf: use is_kernel_addr macro in perf_get_misc_flags()
powerpc/perf: Avoid FAB_*_MATCH checks for power9
powerpc/perf: Add restrictions to PMC5 in power9 DD1
powerpc/perf: Use Instruction Counter value
...
Apart from adding the helper function itself, the rest of the kernel is
converted mechanically using:
git grep -l 'atomic_inc.*mm_count' | xargs sed -i 's/atomic_inc(&\(.*\)->mm_count);/mmgrab\(\1\);/'
git grep -l 'atomic_inc.*mm_count' | xargs sed -i 's/atomic_inc(&\(.*\)\.mm_count);/mmgrab\(\&\1\);/'
This is needed for a later patch that hooks into the helper, but might
be a worthwhile cleanup on its own.
(Michal Hocko provided most of the kerneldoc comment.)
Link: http://lkml.kernel.org/r/20161218123229.22952-1-vegard.nossum@oracle.com
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes
it was possible to remove the IB DMA mapping code entirely and
switch the RDMA stack to use the core DMA mapping code. This resulted
in a nice set of cleanups, but touched the entire tree. This branch
will be submitted separately to Linus at the end of the merge window
as per normal practice for tree wide changes like this.
-----BEGIN PGP SIGNATURE-----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=e0Si
-----END PGP SIGNATURE-----
Merge tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma DMA mapping updates from Doug Ledford:
"Drop IB DMA mapping code and use core DMA code instead.
Bart Van Assche noted that the ib DMA mapping code was significantly
similar enough to the core DMA mapping code that with a few changes it
was possible to remove the IB DMA mapping code entirely and switch the
RDMA stack to use the core DMA mapping code.
This resulted in a nice set of cleanups, but touched the entire tree
and has been kept separate for that reason."
* tag 'for-next-dma_ops' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (37 commits)
IB/rxe, IB/rdmavt: Use dma_virt_ops instead of duplicating it
IB/core: Remove ib_device.dma_device
nvme-rdma: Switch from dma_device to dev.parent
RDS: net: Switch from dma_device to dev.parent
IB/srpt: Modify a debug statement
IB/srp: Switch from dma_device to dev.parent
IB/iser: Switch from dma_device to dev.parent
IB/IPoIB: Switch from dma_device to dev.parent
IB/rxe: Switch from dma_device to dev.parent
IB/vmw_pvrdma: Switch from dma_device to dev.parent
IB/usnic: Switch from dma_device to dev.parent
IB/qib: Switch from dma_device to dev.parent
IB/qedr: Switch from dma_device to dev.parent
IB/ocrdma: Switch from dma_device to dev.parent
IB/nes: Remove a superfluous assignment statement
IB/mthca: Switch from dma_device to dev.parent
IB/mlx5: Switch from dma_device to dev.parent
IB/mlx4: Switch from dma_device to dev.parent
IB/i40iw: Remove a superfluous assignment statement
IB/hns: Switch from dma_device to dev.parent
...
Remove the prototypes for shmem_mapping() and shmem_zero_setup() from
linux/mm.h, since they are already provided in linux/shmem_fs.h. But
shmem_fs.h must then provide the inline stub for shmem_mapping() when
CONFIG_SHMEM is not set, and a few more cfiles now need to #include it.
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1702081658250.1549@eggly.anvils
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This type conversion is a leftover that got ignored during the kcpustat
conversion to nanosecs, resulting in build breakage with config having
CONFIG_NO_HZ_FULL=y.
arch/powerpc/kernel/time.c: In function 'running_clock':
arch/powerpc/kernel/time.c:712:2: error: implicit declaration of function 'cputime_to_nsecs' [-Werror=implicit-function-declaration]
return local_clock() - cputime_to_nsecs(kcpustat_this_cpu->cpustat[CPUTIME_STEAL]);
All we need is to remove it.
Fixes: e7f340ca9c ("powerpc, sched/cputime: Remove unused cputime definitions")
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We will set LPCR with correct value for radix during int. This make sure we
start with a sanitized value of LPCR. In case of kexec, cpus can have LPCR
value based on the previous translation mode we were running.
Fixes: fe036a0605 ("powerpc/64/kexec: Fix MMU cleanup on radix")
Cc: stable@vger.kernel.org # v4.9+
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Optprobes on powerpc are limited to kernel text area. We decided to also
optimize kretprobe_trampoline since that is also in kernel text area.
However,we failed to take into consideration the fact that the same
trampoline is also used to catch function returns from kernel modules.
As an example:
$ sudo modprobe kobject-example
$ sudo bash -c "echo 'r foo_show+8' > /sys/kernel/debug/tracing/kprobe_events"
$ sudo bash -c "echo 1 > /sys/kernel/debug/tracing/events/kprobes/enable"
$ sudo cat /sys/kernel/debug/kprobes/list
c000000000041350 k kretprobe_trampoline+0x0 [OPTIMIZED]
d000000000e00200 r foo_show+0x8 kobject_example
$ cat /sys/kernel/kobject_example/foo
Segmentation fault
With the below (trimmed) splat in dmesg:
Unable to handle kernel paging request for data at address 0xfec40000
Faulting instruction address: 0xc000000000041540
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c000000000041540] optimized_callback+0x70/0xe0
LR [c000000000041e60] optinsn_slot+0xf8/0x10000
Call Trace:
[c0000000c7327850] [c000000000289af4] alloc_set_pte+0x1c4/0x860 (unreliable)
[c0000000c7327890] [c000000000041e60] optinsn_slot+0xf8/0x10000
--- interrupt: 700 at 0xc0000000c7327a80
LR = kretprobe_trampoline+0x0/0x10
[c0000000c7327ba0] [c0000000003a30d4] sysfs_kf_seq_show+0x104/0x1d0
[c0000000c7327bf0] [c0000000003a0bb4] kernfs_seq_show+0x44/0x60
[c0000000c7327c10] [c000000000330578] seq_read+0xf8/0x560
[c0000000c7327cb0] [c0000000003a1e64] kernfs_fop_read+0x194/0x260
[c0000000c7327d00] [c0000000002f9954] __vfs_read+0x44/0x1a0
[c0000000c7327d90] [c0000000002fb4cc] vfs_read+0xbc/0x1b0
[c0000000c7327de0] [c0000000002fd138] SyS_read+0x68/0x110
[c0000000c7327e30] [c00000000000b8e0] system_call+0x38/0xfc
Fix this by loading up the kernel TOC before calling into the kernel.
The original TOC gets restored as part of the usual pt_regs restore.
Fixes: 762df10bad ("powerpc/kprobes: Optimize kprobe in kretprobe_trampoline()")
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Highlights include:
- Support for direct mapped LPC on POWER9, giving Linux direct access to
devices that may be on there such as a UART.
- Memory hotplug support for the Power9 Radix MMU.
- Add new AUX vectors describing the processor's cache geometry, to be used by
glibc.
- The ability for a guest to ask the hypervisor to resize the guest's hash
table, and in addition support for doing so automatically when memory is
hotplugged into/out-of the guest. This allows the hash table to be sized
based on the current memory usage of the guest, rather than the maximum
possible memory usage.
- Implementation of optprobes (kprobe optimisation) for powerpc.
In addition there's the topic branch shared with the KVM tree, which includes
support for guests to use the Radix MMU on Power9.
Thanks to:
Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton Blanchard,
Benjamin Herrenschmidt, Chris Packham, Daniel Axtens, Daniel Borkmann, David
Gibson, Finn Thain, Gautham R. Shenoy, Gavin Shan, Greg Kurz, Joel Stanley,
John Allen, Madhavan Srinivasan, Mahesh Salgaonkar, Markus Elfring, Michael
Neuling, Nathan Fontenot, Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi
Bangoria, Reza Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Icle
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for direct mapped LPC on POWER9, giving Linux direct access
to devices that may be on there such as a UART.
- Memory hotplug support for the Power9 Radix MMU.
- Add new AUX vectors describing the processor's cache geometry, to
be used by glibc.
- The ability for a guest to ask the hypervisor to resize the guest's
hash table, and in addition support for doing so automatically when
memory is hotplugged into/out-of the guest. This allows the hash
table to be sized based on the current memory usage of the guest,
rather than the maximum possible memory usage.
- Implementation of optprobes (kprobe optimisation) for powerpc.
In addition there's the topic branch shared with the KVM tree, which
includes support for guests to use the Radix MMU on Power9.
Thanks to:
Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T, Anton
Blanchard, Benjamin Herrenschmidt, Chris Packham, Daniel Axtens,
Daniel Borkmann, David Gibson, Finn Thain, Gautham R. Shenoy, Gavin
Shan, Greg Kurz, Joel Stanley, John Allen, Madhavan Srinivasan,
Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Nathan Fontenot,
Naveen N. Rao, Nicholas Piggin, Paul Mackerras, Ravi Bangoria, Reza
Arbab, Shailendra Singh, Vaibhav Jain, Wei Yongjun"
* tag 'powerpc-4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (129 commits)
powerpc/mm/radix: Skip ptesync in pte update helpers
powerpc/mm/radix: Use ptep_get_and_clear_full when clearing pte for full mm
powerpc/mm/radix: Update pte update sequence for pte clear case
powerpc/mm: Update PROTFAULT handling in the page fault path
powerpc/xmon: Fix data-breakpoint
powerpc/mm: Fix build break with BOOK3S_64=n and MEMORY_HOTPLUG=y
powerpc/mm: Fix build break when CMA=n && SPAPR_TCE_IOMMU=y
powerpc/mm: Fix build break with RADIX=y & HUGETLBFS=n
powerpc/pseries: Fix typo in parameter description
powerpc/kprobes: Remove kprobe_exceptions_notify()
kprobes: Introduce weak variant of kprobe_exceptions_notify()
powerpc/ftrace: Fix confusing help text for DISABLE_MPROFILE_KERNEL
powerpc/powernv: Fix opal_exit tracepoint opcode
powerpc: Add a prototype for mcount() so it can be versioned
powerpc: Drop GPL from of_node_to_nid() export to match other arches
powerpc/kprobes: Optimize kprobe in kretprobe_trampoline()
powerpc/kprobes: Implement Optprobes
powerpc/kprobes: Fixes for kprobe_lookup_name() on BE
powerpc: Add helper to check if offset is within relative branch range
powerpc/bpf: Introduce __PPC_SH64()
...
With the inclusion of commit 333f7b7686 ("powerpc/pseries: Implement
indexed-count hotplug memory add") and commit 753843471c
("powerpc/pseries: Implement indexed-count hotplug memory remove"), we
now have complete handling of the RTAS hotplug event format as described
by PAPR via ACR "PAPR Changes for Hotplug RTAS Events".
This capability is indicated by byte 6, bit 2 (5 in IBM numbering) of
architecture option vector 5, and allows for greater control over
cpu/memory/pci hot plug/unplug operations.
Existing pseries kernels will utilize this capability based on the
existence of the /event-sources/hot-plug-events DT property, so we
only need to advertise it via CAS and do not need a corresponding
FW_FEATURE_* value to test for.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull scheduler updates from Ingo Molnar:
"The main changes in this (fairly busy) cycle were:
- There was a class of scheduler bugs related to forgetting to update
the rq-clock timestamp which can cause weird and hard to debug
problems, so there's a new debug facility for this: which uncovered
a whole lot of bugs which convinced us that we want to keep the
debug facility.
(Peter Zijlstra, Matt Fleming)
- Various cputime related updates: eliminate cputime and use u64
nanoseconds directly, simplify and improve the arch interfaces,
implement delayed accounting more widely, etc. - (Frederic
Weisbecker)
- Move code around for better structure plus cleanups (Ingo Molnar)
- Move IO schedule accounting deeper into the scheduler plus related
changes to improve the situation (Tejun Heo)
- ... plus a round of sched/rt and sched/deadline fixes, plus other
fixes, updats and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (85 commits)
sched/core: Remove unlikely() annotation from sched_move_task()
sched/autogroup: Rename auto_group.[ch] to autogroup.[ch]
sched/topology: Split out scheduler topology code from core.c into topology.c
sched/core: Remove unnecessary #include headers
sched/rq_clock: Consolidate the ordering of the rq_clock methods
delayacct: Include <uapi/linux/taskstats.h>
sched/core: Clean up comments
sched/rt: Show the 'sched_rr_timeslice' SCHED_RR timeslice tuning knob in milliseconds
sched/clock: Add dummy clear_sched_clock_stable() stub function
sched/cputime: Remove generic asm headers
sched/cputime: Remove unused nsec_to_cputime()
s390, sched/cputime: Remove unused cputime definitions
powerpc, sched/cputime: Remove unused cputime definitions
s390, sched/cputime: Make arch_cpu_idle_time() to return nsecs
ia64, sched/cputime: Remove unused cputime definitions
ia64: Convert vtime to use nsec units directly
ia64, sched/cputime: Move the nsecs based cputime headers to the last arch using it
sched/cputime: Remove jiffies based cputime
sched/cputime, vtime: Return nsecs instead of cputime_t to account
sched/cputime: Complete nsec conversion of tick based accounting
...
The CAPI driver creates virtual PHB (vPHB) from the CAPI adapter.
The vPHB's IO and memory windows aren't built from device-tree node
as we do for normal PHBs. A error message is thrown in below path
when trying to probe AFUs contained in the adapter. The error message
is confusing and unnecessary.
cxl_probe()
pci_init_afu()
cxl_pci_vphb_add()
pcibios_scan_phb()
pcibios_setup_phb_resources()
This removes the error message. We might have the case where the
first memory window on real PHB isn't populated properly because
of error in "ranges" property in the device-tree node. We can check
the device-tree instead for that. This also removes one unnecessary
blank line in the function.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PVR value of 0x0F000005 means we are arch v3.00 compliant (i.e. POWER9).
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Russell Currey <ruscur@russell.cc>
[mpe: Don't set num_pmcs, so we keep the PMU fields from the raw entry]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are quite a few entries in asm-offests.c which look like:
DEFINE(REG, STACK_FRAME_OVERHEAD+offsetof(struct pt_regs, reg));
So define a macro to do it once.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
[mpe: Rename to STACK_PT_REGS_OFFSET for excruciating explicitness]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A lot of entries in asm-offests.c look like this:
DEFINE(TI_FLAGS, offsetof(struct thread_info, flags));
But there is a common macro, OFFSET, which makes this cleaner:
OFFSET(TI_flags, thread_info, flags)
So use it.
Signed-off-by: Rashmica Gupta <rashmicy@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
WARN_ONCE() takes a condition and a format string. We were passing a
constant string as the condition, and the function name as the format
string. It would work, but the message would be just the function name.
Fix it by just using WARN_ONCE() directly instead of if (x) WARN_ONCE().
Noticed-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently xmon data-breakpoint feature is broken.
Whenever there is a watchpoint match occurs, hw_breakpoint_handler will
be called by do_break via notifier chains mechanism. If watchpoint is
registered by xmon, hw_breakpoint_handler won't find any associated
perf_event and returns immediately with NOTIFY_STOP. Similarly, do_break
also returns without notifying to xmon.
Solve this by returning NOTIFY_DONE when hw_breakpoint_handler does not
find any perf_event associated with matched watchpoint, rather than
NOTIFY_STOP, which tells the core code to continue calling the other
breakpoint handlers including the xmon one.
Cc: stable@vger.kernel.org
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
... as the generic weak variant will do.
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Kprobe placed on the kretprobe_trampoline() during boot time can be
optimized, since the instruction at probe point is a 'nop'.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Current infrastructure of kprobe uses the unconditional trap instruction
to probe a running kernel. Optprobe allows kprobe to replace the trap
with a branch instruction to a detour buffer. Detour buffer contains
instructions to create an in memory pt_regs. Detour buffer also has a
call to optimized_callback() which in turn call the pre_handler(). After
the execution of the pre-handler, a call is made for instruction
emulation. The NIP is determined in advanced through dummy instruction
emulation and a branch instruction is created to the NIP at the end of
the trampoline.
To address the limitation of branch instruction in POWER architecture,
detour buffer slot is allocated from a reserved area. For the time
being, 64KB is reserved in memory for this purpose.
Instructions which can be emulated using analyse_instr() are the
candidates for optimization. Before optimization ensure that the address
range between the detour buffer allocated and the instruction being
probed is within +/- 32MB.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The hypervisor needs to know a guest is capable of using the HPT resizing
PAPR extension in order to make full advantage of it for memory hotplug.
If the hypervisor knows the guest is HPT resize aware, it can size the
initial HPT based on the initial guest RAM size, relying on the guest to
resize the HPT when more memory is hot-added. Without this, the hypervisor
must size the HPT for the maximum possible guest RAM, which can lead to
a huge waste of space if the guest never actually expends to that maximum
size.
This patch advertises the guest's support for HPT resizing via the
ibm,client-architecture-support OF interface. We use bit 5 of byte 6 of
option vector 5 for this purpose, as defined in the PAPR ACR "HPT
resizing option".
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Reviewed-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All entry points already read the MSR so they can easily do
the right thing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The branch from hmi_exception_early to hmi_exception_realmode must use
a "relocatable-style" branch, because it is branching from unrelocated
exception code to beyond __end_interrupts.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
start,size has the benefit of being easier to search for (start,end
usually gives you the preceeding vector from the one you want, as first
result).
Suggested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Somewhere along the line, search/replace left some naming garbled,
and untidy alignment (aka. mpe stuffed it up). Might as well fix them
all up now while git blame history doesn't extend too far.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds AUX vectors for the L1I,D, L2 and L3 cache levels
providing for each cache level the size of the cache in bytes
and the geometry (line size and number of ways).
We chose to not use the existing alpha/sh definition which
packs all the information in a single entry per cache level as
it is too restricted to represent some of the geometries used
on POWER.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
All shipping firmware versions have it wrong in the device-tree
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Retrieved from device-tree when available
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have two set of identical struct members for the I and D sides
and mostly identical bunches of code to parse the device-tree to
populate them. Instead make a ppc_cache_info structure with one
copy for I and one for D
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It will be used to calculate the associativity
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In a number of places we called "cache line size" what is actually
the cache block size, which in the powerpc architecture, means the
effective size to use with cache management instructions (it can
be different from the actual cache line size).
We fix the naming across the board and properly retrieve both
pieces of information when available in the device-tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We don't patch instructions based on the cache lines or block
sizes these days.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The variables are defined twice in setup_32.c and setup_64.c, do it
once in setup-common.c instead
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The main change is we're reverting the initial stack protector support we
merged this cycle. It turns out to not work on toolchains built with libc
support, and fixing it will be need to wait for another release.
And the rest are all fairly minor:
- Some pasemi machines were not booting due to a missing error check in
prom_find_boot_cpu().
- In EEH we were checking a pointer rather than the bool it pointed to.
- The clang build was broken by a BUILD_BUG_ON() we added.
- The radix (Power9 only) version of map_kernel_page() was broken if our
memory size was a multiple of 2MB, which it generally isn't.
Thanks to:
Darren Stevens, Gavin Shan, Reza Arbab.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XUAi
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"The main change is we're reverting the initial stack protector support
we merged this cycle. It turns out to not work on toolchains built
with libc support, and fixing it will be need to wait for another
release.
And the rest are all fairly minor:
- Some pasemi machines were not booting due to a missing error check
in prom_find_boot_cpu()
- In EEH we were checking a pointer rather than the bool it pointed
to
- The clang build was broken by a BUILD_BUG_ON() we added.
- The radix (Power9 only) version of map_kernel_page() was broken if
our memory size was a multiple of 2MB, which it generally isn't
Thanks to: Darren Stevens, Gavin Shan, Reza Arbab"
* tag 'powerpc-4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Use the correct pointer when setting a 2MB pte
powerpc: Fix build failure with clang due to BUILD_BUG_ON()
powerpc: Revert the initial stack protector support
powerpc/eeh: Fix wrong flag passed to eeh_unfreeze_pe()
powerpc: Add missing error check to prom_find_boot_cpu()
The modversion symbol CRCs are emitted as ELF symbols, which allows us
to easily populate the kcrctab sections by relying on the linker to
associate each kcrctab slot with the correct value.
This has a couple of downsides:
- Given that the CRCs are treated as memory addresses, we waste 4 bytes
for each CRC on 64 bit architectures,
- On architectures that support runtime relocation, a R_<arch>_RELATIVE
relocation entry is emitted for each CRC value, which identifies it
as a quantity that requires fixing up based on the actual runtime
load offset of the kernel. This results in corrupted CRCs unless we
explicitly undo the fixup (and this is currently being handled in the
core module code)
- Such runtime relocation entries take up 24 bytes of __init space
each, resulting in a x8 overhead in [uncompressed] kernel size for
CRCs.
Switching to explicit 32 bit values on 64 bit architectures fixes most
of these issues, given that 32 bit values are not treated as quantities
that require fixing up based on the actual runtime load offset. Note
that on some ELF64 architectures [such as PPC64], these 32-bit values
are still emitted as [absolute] runtime relocatable quantities, even if
the value resolves to a build time constant. Since relative relocations
are always resolved at build time, this patch enables MODULE_REL_CRCS on
powerpc when CONFIG_RELOCATABLE=y, which turns the absolute CRC
references into relative references into .rodata where the actual CRC
value is stored.
So redefine all CRC fields and variables as u32, and redefine the
__CRC_SYMBOL() macro for 64 bit builds to emit the CRC reference using
inline assembler (which is necessary since 64-bit C code cannot use
32-bit types to hold memory addresses, even if they are ultimately
resolved using values that do not exceed 0xffffffff). To avoid
potential problems with legacy 32-bit architectures using legacy
toolchains, the equivalent C definition of the kcrctab entry is retained
for 32-bit architectures.
Note that this mostly reverts commit d4703aefdb ("module: handle ppc64
relocating kcrctabs when CONFIG_RELOCATABLE=y")
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 38addce8b6 ("gcc-plugins: Add latent_entropy plugin") excludes
certain powerpc early boot code from the latent entropy plugin by adding
appropriate CFLAGS. It looks like this was supposed to cover
prom_init.o, but ended up saying init.o (which doesn't exist) instead.
Fix the typo.
Fixes: 38addce8b6 ("gcc-plugins: Add latent_entropy plugin")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Extend the existing PRRN infrastructure to perform the actual affinity
updating for cpus and memory in addition to the device tree updating.
For cpus, dynamic affinity updating already appears to exist in the
kernel in the form of arch_update_cpu_topology(). For memory, we must
place a READD operation on the hotplug queue for any phandle included in
the PRRN event that is determined to be an LMB.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since the core doesn't deal with cputime_t anymore, most of these APIs
have been left unused. Lets remove these.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-33-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is one more step toward converting cputime accounting to pure nsecs.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-25-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is one more step toward converting cputime accounting to pure nsecs.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-24-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is one more step toward converting cputime accounting to pure nsecs.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-23-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This is one more step toward converting cputime accounting to pure nsecs.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-22-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that most cputime readers use the transition API which return the
task cputime in old style cputime_t, we can safely store the cputime in
nsecs. This will eventually make cputime statistics less opaque and more
granular. Back and forth convertions between cputime_t and nsecs in order
to deal with cputime_t random granularity won't be needed anymore.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1485832191-26889-8-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This adds code to branch around the parts that radix guests don't
need - clearing and loading the SLB with the guest SLB contents,
saving the guest SLB contents on exit, and restoring the host SLB
contents.
Since the host is now using radix, we need to save and restore the
host value for the PID register.
On hypervisor data/instruction storage interrupts, we don't do the
guest HPT lookup on radix, but just save the guest physical address
for the fault (from the ASDR register) in the vcpu struct.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With host and guest both using radix translation, it is feasible
for the host to take interrupts that come from the guest with
relocation on, and that is in fact what the POWER9 hardware will
do when LPCR[AIL] = 3. All such interrupts use HSRR0/1 not SRR0/1
except for system call with LEV=1 (hcall).
Therefore this adds the KVM tests to the _HV variants of the
relocation-on interrupt handlers, and adds the KVM test to the
relocation-on system call entry point.
We also instantiate the relocation-on versions of the hypervisor
data storage and instruction interrupt handlers, since these can
occur with relocation on in radix guests.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To use radix as a guest, we first need to tell the hypervisor via
the ibm,client-architecture call first that we support POWER9 and
architecture v3.00, and that we can do either radix or hash and
that we would like to choose later using an hcall (the
H_REGISTER_PROC_TBL hcall).
Then we need to check whether the hypervisor agreed to us using
radix. We need to do this very early on in the kernel boot process
before any of the MMU initialization is done. If the hypervisor
doesn't agree, we can't use radix and therefore clear the radix
MMU feature bit.
Later, when we have set up our process table, which points to the
radix tree for each process, we need to install that using the
H_REGISTER_PROC_TBL hcall.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
64-bit Book3S exception handlers must find the dynamic kernel base
to add to the target address when branching beyond __end_interrupts,
in order to support kernel running at non-0 physical address.
Support this in KVM by branching with CTR, similarly to regular
interrupt handlers. The guest CTR saved in HSTATE_SCRATCH1 and
restored after the branch.
Without this, the host kernel hangs and crashes randomly when it is
running at a non-0 address and a KVM guest is started.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the new non-PCI ISA bridge support to expose the POWER9
LPC bus as direct mapped via the ISA IO port range. This
enables direct access via drivers such as 8250
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The POWER9 chip supports an LPC bus that isn't hanging
off a PCI bus, so let's add support for that, mapping it
to the reserved space at ISA_IO_BASE
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We'll be adding non-PCI isa bridge support so let's not
have all the definition in pci-bridge.h
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The power9_idle_stop method currently takes only the requested stop
level as a parameter and picks up the rest of the PSSCR bits from a
hand-coded macro. This is not a very flexible design, especially when
the firmware has the capability to communicate the psscr value and the
mask associated with a particular stop state via device tree.
This patch modifies the power9_idle_stop API to take as parameters the
PSSCR value and the PSSCR mask corresponding to the stop state that
needs to be set. These PSSCR value and mask are respectively obtained
by parsing the "ibm,cpu-idle-state-psscr" and
"ibm,cpu-idle-state-psscr-mask" fields from the device tree.
In addition to this, the patch adds support for handling stop states
for which ESL and EC bits in the PSSCR are zero. As per the
architecture, a wakeup from these stop states resumes execution from
the subsequent instruction as opposed to waking up at the System
Vector.
The older firmware sets only the Requested Level (RL) field in the
psscr and psscr-mask exposed in the device tree. For older firmware
where psscr-mask=0xf, this patch will set the default sane values that
the set for for remaining PSSCR fields (i.e PSLL, MTL, ESL, EC, and
TR). For the new firmware, the patch will validate that the invariants
required by the ISA for the psscr values are maintained by the
firmware.
This skiboot patch that exports fully populated PSSCR values and the
mask for all the stop states can be found here:
https://lists.ozlabs.org/pipermail/skiboot/2016-September/004869.html
[Optimize the number of instructions before entering STOP with
ESL=EC=0, validate the PSSCR values provided by the firimware
maintains the invariants required as per the ISA suggested by Balbir
Singh]
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently all the low-power idle states are expected to wake up
at reset vector 0x100. Which is why the macro IDLE_STATE_ENTER_SEQ
that puts the CPU to an idle state and never returns.
On ISA v3.0, when the ESL and EC bits in the PSSCR are zero, the CPU
is expected to wake up at the next instruction of the idle
instruction.
This patch adds a new macro named IDLE_STATE_ENTER_SEQ_NORET for the
no-return variant and reuses the name IDLE_STATE_ENTER_SEQ
for a variant that allows resuming operation at the instruction next
to the idle-instruction.
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are chances that multiple CPUs can call crash_fadump() simultaneously
and would start duplicating same info to vmcoreinfo ELF note section. This
causes makedumpfile to fail during kdump capture. One example is,
triggering dumprestart from HMC which sends system reset to all the CPUs at
once.
makedumpfile --dump-dmesg /proc/vmcore
read_vmcoreinfo_basic_info: Invalid data in /tmp/vmcoreinfoyjgxlL: CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971
makedumpfile Failed.
Running makedumpfile --dump-dmesg /proc/vmcore failed (1).
makedumpfile -d 31 -l /proc/vmcore
read_vmcoreinfo_basic_info: Invalid data in /tmp/vmcoreinfo1mmVdO: CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971CRASHTIME=1475605971
makedumpfile Failed.
Running makedumpfile -d 31 -l /proc/vmcore failed (1).
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A subsequent patch to make KVM handlers relocation-safe makes them
unusable from within alt section "else" cases (due to the way fixed
addresses are taken from within fixed section head code).
Stop open-coding the KVM handlers, and add them both as normal. A more
optimal fix may be to allow some level of alternate feature patching in
the exception macros themselves, but for now this will do.
The TRAMP_KVM handlers must be moved to the "virt" fixed section area
(name is arbitrary) in order to be closer to .text and avoid the dreaded
"relocation truncated to fit" error.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch has been reworked since RFC version. In the RFC, this patch
was preceded by a patch clearing MSR RI for all PPC32 at all time at
exception prologs. Now MSR RI clearing is done only when this 8xx perf
events functionality is compiled in, it is therefore limited to 8xx
and merged inside this patch.
Other main changes have been to take into account detailed review from
Peter Zijlstra. The instructions counter has been reworked to behave
as a free running counter like the three other counters.
The 8xx has no PMU, however some events can be emulated by other means.
This patch implements the following events (as reported by 'perf list'):
cpu-cycles OR cycles [Hardware event]
instructions [Hardware event]
dTLB-load-misses [Hardware cache event]
iTLB-load-misses [Hardware cache event]
'cycles' event is implemented using the timebase clock. Timebase clock
corresponds to CPU clock divided by 16, so number of cycles is
approximatly 16 times the number of TB ticks
On the 8xx, TLB misses are handled by software. It is therefore
easy to count all TLB misses each time the TLB miss exception is
called.
'instructions' is calculated by using instruction watchpoint counter.
This patch sets counter A to count instructions at address greater
than 0, hence we count all instructions executed while MSR RI bit is
set. The counter is set to the maximum which is 0xffff. Every 65535
instructions, debug instruction breakpoint exception fires. The
exception handler increments a counter in memory which then
represent the upper part of the instruction counter. We therefore
end up with a 48 bits counter. In order to avoid unnecessary overhead
while no perf event is active, this counter is started when the first
event referring to this counter is added, and the counter is stopped
when the last event referring to it is deleted. In order to properly
support breakpoint exceptions, MSR RI bit has to be unset in exception
epilogs in order to avoid breakpoint exceptions during critical
sections during changes to SRR0 and SRR1 would be problematic.
All counters are handled as free running counters.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
FIX_SRR1() is defined as blank. Last useful instance of FIX_SRR1()
was removed by commit 40ef8cbc6d ("powerpc: Get 64-bit configs to
compile with ARCH=powerpc") in 2005.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch implements HW breakpoint on the 8xx. The 8xx has
capability to manage HW breakpoints, which is slightly different
than BOOK3S:
1/ The breakpoint match doesn't trigger a DSI exception but a
dedicated data breakpoint exception.
2/ The breakpoint happens after the instruction has completed,
no need to single step or emulate the instruction,
3/ Matched address is not set in DAR but in BAR,
4/ DABR register doesn't exist, instead we have registers
LCTRL1, LCTRL2 and CMPx registers,
5/ The match on one comparator is not on a double word but
on a single word.
The patch does:
1/ Prepare the dedicated registers in call to __set_dabr(). In order
to emulate the double word handling of BOOK3S, comparator E is set to
DABR address value and comparator F to address + 4. Then breakpoint 1
is set to match comparator E or F,
2/ Skip the singlestepping stage when compiled for CONFIG_PPC_8xx,
3/ Implement the exception. In that exception, the matched address
is taken from SPRN_BAR and manage as if it was from SPRN_DAR.
4/ I/D TLB error exception routines perform a tlbie on bad TLBs. That
tlbie triggers the breakpoint exception when performed on the
breakpoint address. For this reason, the routine returns if the match
is from one of those two tlbie.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
The RTAS device-tree node's refcount has been increased by one in
the function call of_find_node_by_name(), but it's missed to be
decreased by one in the error path. It leads to unbalanced refcount
on RTAS device-tree node.
This fixes above issue by decreasing RTAS device-tree node's refcount
in error path.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This uses of_property_read_u32() in rtas_initialize() so that we
needn't explicitly care the CPU's endian.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This removes the unnecessary nested if statements in function
rtas_initialize(), to simplify the code. No functional changes
introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some but not all architectures provide set_dma_ops(). Move dma_ops
from struct dev_archdata into struct device such that it becomes
possible on all architectures to configure dma_ops per device.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Cc: x86@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Unfortunately the stack protector support we merged recently only works
on some toolchains. If the toolchain is built without glibc support
everything works fine, but if glibc is built then it leads to a panic
at boot.
The solution is not rc5 material, so revert the support for now. This
reverts commits:
6533b7c16e ("powerpc: Initial stack protector (-fstack-protector) support")
902e06eb86 ("powerpc/32: Change the stack protector canary value per task")
Fixes: 6533b7c16e ("powerpc: Initial stack protector (-fstack-protector) support")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In __eeh_clear_pe_frozen_state(), we should pass the flag's value
instead of its address to eeh_unfreeze_pe(). The isolated flag is
cleared if no error returned from __eeh_clear_pe_frozen_state(). We
never observed the error from the function. So the isolated flag should
have been always cleared, no real issue is caused because of the misused
@flag.
This fixes the code by passing the value of @flag to eeh_unfreeze_pe().
Fixes: 5cfb20b96f ("powerpc/eeh: Emulate EEH recovery for VFIO devices")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
prom_init.c calls 'instance-to-package' twice, but the return
is not checked during prom_find_boot_cpu(). The result is then
passed to prom_getprop(), which could be PROM_ERROR. Add a return check
to prevent this.
This was found on a pasemi system, where CFE doesn't have a working
'instance-to package' prom call.
Before Commit 5c0484e25e ('powerpc: Endian safe trampoline') the area
around addr 0 was mostly 0's and this doesn't cause a problem. Once the
macro 'FIXUP_ENDIAN' has been added to head_64.S, the low memory area
now has non-zero values, which cause the prom_getprop() call
to hang.
mpe: Also confirmed that under SLOF if 'instance-to-package' did fail
with PROM_ERROR we would crash in SLOF. So the bug is not specific to
CFE, it's just that other open firmwares don't trigger it because they
have a working 'instance-to-package'.
Fixes: 5c0484e25e ("powerpc: Endian safe trampoline")
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Darren Stevens <darren@stevens-zone.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the check pointed registers, the thread's old check pointed
registers are preserved.
Fixes: 9d3918f7c0 ("powerpc/ptrace: Enable support for NT_PPC_CVSX")
Fixes: 19cbcbf75a ("powerpc/ptrace: Enable support for NT_PPC_CFPR")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the registers, the thread's old registers are preserved.
Fixes: c6e6771b87 ("powerpc: Introduce VSX thread_struct and CONFIG_VSX")
Cc: stable@vger.kernel.org # v2.6.27+
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We give up recovery on permanent error, simply shutdown the affected
devices and remove them. If the devices can't be put into quiet state,
they spew more traffic that is likely to cause another unexpected EEH
error. This was observed on "p8dtu2u" machine:
0002:00:00.0 PCI bridge: IBM Device 03dc
0002:01:00.0 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
0002:01:00.1 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
0002:01:00.2 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
0002:01:00.3 Ethernet controller: Intel Corporation \
Ethernet Controller X710/X557-AT 10GBASE-T (rev 02)
On P8 PowerNV platform, the IO path is frozen when shutdowning the
devices, meaning the memory registers are inaccessible. It is why
the devices can't be put into quiet state before removing them.
This fixes the issue by enabling IO path prior to putting the devices
into quiet state.
Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_VIRT_CPU_ACCOUNTING_NATIVE=y used to accumulate user time and
account it on ticks and context switches only through the
vtime_account_user() function.
Now this model has been generalized on the 3 archs for all kind of
cputime (system, irq, ...) and all the cputime flushing happens under
vtime_account_user().
So let's rename this function to better reflect its new role.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1483636310-6557-11-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently CONFIG_VIRT_CPU_ACCOUNTING_NATIVE=y accounts the cputime on
any context boundary: irq entry/exit, guest entry/exit, context switch,
etc...
Calling functions such as account_system_time(), account_user_time()
and such can be costly, especially if they are called on many fastpath
such as twice per IRQ. Those functions do more than just accounting to
kcpustat and task cputime. Depending on the config, some subsystems can
perform unpleasant multiplications and divisions, among other things.
So lets accumulate the cputime instead and delay the accounting on ticks
and context switches only.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1483636310-6557-8-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
That in order to gather all cputime accumulation to the same place.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1483636310-6557-7-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to prepare for CONFIG_VIRT_CPU_ACCOUNTING_NATIVE=y to delay
cputime accounting to the tick, provide finegrained accumulators to
powerpc in order to store the cputime until flushing.
While at it, normalize the name of several fields according to common
cputime naming.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1483636310-6557-6-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On context switch with powerpc32, the cputime is accumulated in the
thread_info struct. So the switching-in task must move forward its
start time snapshot to the current time in order to later compute the
delta spent in system mode.
This is what we do for the normal cputime by initializing the starttime
field to the value of the previous task's starttime which got freshly
updated.
But we are missing the update of the scaled cputime start time. As a
result we may be accounting too much scaled cputime later.
Fix this by initializing the scaled cputime the same way we do for
normal cputime.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1483636310-6557-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:
AS arch/powerpc/kernel/misc_32.o
arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]
This problem is evident after commit 989cea5c14 ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created. That was with commit 9994a33865 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").
The offending line does not make a lot of sense. This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.
Thanks to Nicholas Piggin for suggesting this solution.
Fixes: 9994a33865 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IMA kexec buffer allows the currently running kernel to pass the
measurement list via a kexec segment to the kernel that will be kexec'd.
This is the architecture-specific part of setting up the IMA kexec
buffer for the next kernel. It will be used in the next patch.
Link: http://lkml.kernel.org/r/1480554346-29071-6-git-send-email-zohar@linux.vnet.ibm.com
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andreas Steffen <andreas.steffen@strongswan.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Cc: Josh Sklar <sklar@linux.vnet.ibm.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "ima: carry the measurement list across kexec", v8.
The TPM PCRs are only reset on a hard reboot. In order to validate a
TPM's quote after a soft reboot (eg. kexec -e), the IMA measurement
list of the running kernel must be saved and then restored on the
subsequent boot, possibly of a different architecture.
The existing securityfs binary_runtime_measurements file conveniently
provides a serialized format of the IMA measurement list. This patch
set serializes the measurement list in this format and restores it.
Up to now, the binary_runtime_measurements was defined as architecture
native format. The assumption being that userspace could and would
handle any architecture conversions. With the ability of carrying the
measurement list across kexec, possibly from one architecture to a
different one, the per boot architecture information is lost and with it
the ability of recalculating the template digest hash. To resolve this
problem, without breaking the existing ABI, this patch set introduces
the boot command line option "ima_canonical_fmt", which is arbitrarily
defined as little endian.
The need for this boot command line option will be limited to the
existing version 1 format of the binary_runtime_measurements.
Subsequent formats will be defined as canonical format (eg. TPM 2.0
support for larger digests).
A simplified method of Thiago Bauermann's "kexec buffer handover" patch
series for carrying the IMA measurement list across kexec is included in
this patch set. The simplified method requires all file measurements be
taken prior to executing the kexec load, as subsequent measurements will
not be carried across the kexec and restored.
This patch (of 10):
The IMA kexec buffer allows the currently running kernel to pass the
measurement list via a kexec segment to the kernel that will be kexec'd.
The second kernel can check whether the previous kernel sent the buffer
and retrieve it.
This is the architecture-specific part which enables IMA to receive the
measurement list passed by the previous kernel. It will be used in the
next patch.
The change in machine_kexec_64.c is to factor out the logic of removing
an FDT memory reservation so that it can be used by remove_ima_buffer.
Link: http://lkml.kernel.org/r/1480554346-29071-2-git-send-email-zohar@linux.vnet.ibm.com
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andreas Steffen <andreas.steffen@strongswan.org>
Cc: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Cc: Josh Sklar <sklar@linux.vnet.ibm.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for secure and
trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and store
them as relative offsets to save space in the kernel image & memory.
- Allow building the kernel with thin archives, which should allow us to build
an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the kernel endian
from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9 Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage support,
qbman fixes/cleanup, device tree updates, and some misc cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual,
Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz, Christophe Jaillet,
Christophe Leroy, Denis Kirjanov, Elimar Riesebieter, Frederic Barrat,
Gautham R. Shenoy, Geliang Tang, Geoff Levand, Jack Miller, Johan Hovold,
Lars-Peter Clausen, Libin, Madhavan Srinivasan, Michael Neuling, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin,
Rashmica Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xOzf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for
secure and trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to
SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and
store them as relative offsets to save space in the kernel image &
memory.
- Allow building the kernel with thin archives, which should allow us
to build an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the
kernel endian from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9
Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via
debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage
support, qbman fixes/cleanup, device tree updates, and some misc
cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz,
Christophe Jaillet, Christophe Leroy, Denis Kirjanov, Elimar
Riesebieter, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff
Levand, Jack Miller, Johan Hovold, Lars-Peter Clausen, Libin,
Madhavan Srinivasan, Michael Neuling, Nathan Fontenot, Naveen N.
Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin, Rashmica
Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain"
[ And thanks to Michael, who took time off from a new baby to get this
pull request done. - Linus ]
* tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (174 commits)
powerpc/fsl/dts: add FMan node for t1042d4rdb
powerpc/fsl/dts: add sg_2500_aqr105_phy4 alias on t1024rdb
powerpc/fsl/dts: add QMan and BMan nodes on t1024
powerpc/fsl/dts: add QMan and BMan nodes on t1023
soc/fsl/qman: test: use DEFINE_SPINLOCK()
powerpc/fsl-lbc: use DEFINE_SPINLOCK()
powerpc/8xx: Implement support of hugepages
powerpc: get hugetlbpage handling more generic
powerpc: port 64 bits pgtable_cache to 32 bits
powerpc/boot: Request no dynamic linker for boot wrapper
soc/fsl/bman: Use resource_size instead of computation
soc/fsl/qe: use builtin_platform_driver
powerpc/fsl_pmc: use builtin_platform_driver
powerpc/83xx/suspend: use builtin_platform_driver
powerpc/ftrace: Fix the comments for ftrace_modify_code
powerpc/perf: macros for power9 format encoding
powerpc/perf: power9 raw event format encoding
powerpc/perf: update attribute_group data structure
powerpc/perf: factor out the event format field
powerpc/mm/iommu, vfio/spapr: Put pages on VFIO container shutdown
...
Merge more updates from Andrew Morton:
- a few misc things
- kexec updates
- DMA-mapping updates to better support networking DMA operations
- IPC updates
- various MM changes to improve DAX fault handling
- lots of radix-tree changes, mainly to the test suite. All leading up
to reimplementing the IDA/IDR code to be a wrapper layer over the
radix-tree. However the final trigger-pulling patch is held off for
4.11.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (114 commits)
radix tree test suite: delete unused rcupdate.c
radix tree test suite: add new tag check
radix-tree: ensure counts are initialised
radix tree test suite: cache recently freed objects
radix tree test suite: add some more functionality
idr: reduce the number of bits per level from 8 to 6
rxrpc: abstract away knowledge of IDR internals
tpm: use idr_find(), not idr_find_slowpath()
idr: add ida_is_empty
radix tree test suite: check multiorder iteration
radix-tree: fix replacement for multiorder entries
radix-tree: add radix_tree_split_preload()
radix-tree: add radix_tree_split
radix-tree: add radix_tree_join
radix-tree: delete radix_tree_range_tag_if_tagged()
radix-tree: delete radix_tree_locate_item()
radix-tree: improve multiorder iterators
btrfs: fix race in btrfs_free_dummy_fs_info()
radix-tree: improve dump output
radix-tree: make radix_tree_find_next_bit more useful
...
This change allows us to pass DMA_ATTR_SKIP_CPU_SYNC which allows us to
avoid invoking cache line invalidation if the driver will just handle it
via a sync_for_cpu or sync_for_device call.
Link: http://lkml.kernel.org/r/20161110113534.76501.86492.stgit@ahduyck-blue-test.jf.intel.com
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull namespace updates from Eric Biederman:
"After a lot of discussion and work we have finally reachanged a basic
understanding of what is necessary to make unprivileged mounts safe in
the presence of EVM and IMA xattrs which the last commit in this
series reflects. While technically it is a revert the comments it adds
are important for people not getting confused in the future. Clearing
up that confusion allows us to seriously work on unprivileged mounts
of fuse in the next development cycle.
The rest of the fixes in this set are in the intersection of user
namespaces, ptrace, and exec. I started with the first fix which
started a feedback cycle of finding additional issues during review
and fixing them. Culiminating in a fix for a bug that has been present
since at least Linux v1.0.
Potentially these fixes were candidates for being merged during the rc
cycle, and are certainly backport candidates but enough little things
turned up during review and testing that I decided they should be
handled as part of the normal development process just to be certain
there were not any great surprises when it came time to backport some
of these fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
Revert "evm: Translate user/group ids relative to s_user_ns when computing HMAC"
exec: Ensure mm->user_ns contains the execed files
ptrace: Don't allow accessing an undumpable mm
ptrace: Capture the ptracer's creds not PT_PTRACE_CAP
mm: Add a user_ns owner to mm_struct and fix ptrace permission checks
x86: userspace can now hide nested VMX features from guests; nested
VMX can now run Hyper-V in a guest; support for AVX512_4VNNIW and
AVX512_FMAPS in KVM; infrastructure support for virtual Intel GPUs.
PPC: support for KVM guests on POWER9; improved support for interrupt
polling; optimizations and cleanups.
s390: two small optimizations, more stuff is in flight and will be
in 4.11.
ARM: support for the GICv3 ITS on 32bit platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQExBAABCAAbBQJYTkP0FBxwYm9uemluaUByZWRoYXQuY29tAAoJEL/70l94x66D
lZIH/iT1n9OQXcuTpYYnQhuCenzI3GZZOIMTbCvK2i5bo0FIJKxVn0EiAAqZSXvO
nO185FqjOgLuJ1AD1kJuxzye5suuQp4HIPWWgNHcexLuy43WXWKZe0IQlJ4zM2Xf
u31HakpFmVDD+Cd1qN3yDXtDrRQ79/xQn2kw7CWb8olp+pVqwbceN3IVie9QYU+3
gCz0qU6As0aQIwq2PyalOe03sO10PZlm4XhsoXgWPG7P18BMRhNLTDqhLhu7A/ry
qElVMANT7LSNLzlwNdpzdK8rVuKxETwjlc1UP8vSuhrwad4zM2JJ1Exk26nC2NaG
D0j4tRSyGFIdx6lukZm7HmiSHZ0=
=mkoB
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Small release, the most interesting stuff is x86 nested virt
improvements.
x86:
- userspace can now hide nested VMX features from guests
- nested VMX can now run Hyper-V in a guest
- support for AVX512_4VNNIW and AVX512_FMAPS in KVM
- infrastructure support for virtual Intel GPUs.
PPC:
- support for KVM guests on POWER9
- improved support for interrupt polling
- optimizations and cleanups.
s390:
- two small optimizations, more stuff is in flight and will be in
4.11.
ARM:
- support for the GICv3 ITS on 32bit platforms"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (94 commits)
arm64: KVM: pmu: Reset PMSELR_EL0.SEL to a sane value before entering the guest
KVM: arm/arm64: timer: Check for properly initialized timer on init
KVM: arm/arm64: vgic-v2: Limit ITARGETSR bits to number of VCPUs
KVM: x86: Handle the kthread worker using the new API
KVM: nVMX: invvpid handling improvements
KVM: nVMX: check host CR3 on vmentry and vmexit
KVM: nVMX: introduce nested_vmx_load_cr3 and call it on vmentry
KVM: nVMX: propagate errors from prepare_vmcs02
KVM: nVMX: fix CR3 load if L2 uses PAE paging and EPT
KVM: nVMX: load GUEST_EFER after GUEST_CR0 during emulated VM-entry
KVM: nVMX: generate MSR_IA32_CR{0,4}_FIXED1 from guest CPUID
KVM: nVMX: fix checks on CR{0,4} during virtual VMX operation
KVM: nVMX: support restore of VMX capability MSRs
KVM: nVMX: generate non-true VMX MSRs based on true versions
KVM: x86: Do not clear RFLAGS.TF when a singlestep trap occurs.
KVM: x86: Add kvm_skip_emulated_instruction and use it.
KVM: VMX: Move skip_emulated_instruction out of nested_vmx_check_vmcs12
KVM: VMX: Reorder some skip_emulated_instruction calls
KVM: x86: Add a return value to kvm_emulate_cpuid
KVM: PPC: Book3S: Move prototypes for KVM functions into kvm_ppc.h
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the final round of converting the notifier mess to the state
machine. The removal of the notifiers and the related infrastructure
will happen around rc1, as there are conversions outstanding in other
trees.
The whole exercise removed about 2000 lines of code in total and in
course of the conversion several dozen bugs got fixed. The new
mechanism allows to test almost every hotplug step standalone, so
usage sites can exercise all transitions extensively.
There is more room for improvement, like integrating all the
pointlessly different architecture mechanisms of synchronizing,
setting cpus online etc into the core code"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
tracing/rb: Init the CPU mask on allocation
soc/fsl/qbman: Convert to hotplug state machine
soc/fsl/qbman: Convert to hotplug state machine
zram: Convert to hotplug state machine
KVM/PPC/Book3S HV: Convert to hotplug state machine
arm64/cpuinfo: Convert to hotplug state machine
arm64/cpuinfo: Make hotplug notifier symmetric
mm/compaction: Convert to hotplug state machine
iommu/vt-d: Convert to hotplug state machine
mm/zswap: Convert pool to hotplug state machine
mm/zswap: Convert dst-mem to hotplug state machine
mm/zsmalloc: Convert to hotplug state machine
mm/vmstat: Convert to hotplug state machine
mm/vmstat: Avoid on each online CPU loops
mm/vmstat: Drop get_online_cpus() from init_cpu_node_state/vmstat_cpu_dead()
tracing/rb: Convert to hotplug state machine
oprofile/nmi timer: Convert to hotplug state machine
net/iucv: Use explicit clean up labels in iucv_init()
x86/pci/amd-bus: Convert to hotplug state machine
x86/oprofile/nmi: Convert to hotplug state machine
...
8xx uses a two level page table with two different linux page size
support (4k and 16k). 8xx also support two different hugepage sizes
512k and 8M. In order to support them on linux we define two different
page table layout.
The size of pages is in the PGD entry, using PS field (bits 28-29):
00 : Small pages (4k or 16k)
01 : 512k pages
10 : reserved
11 : 8M pages
For 512K hugepage size a pgd entry have the below format
[<hugepte address >0101] . The hugepte table allocated will contain 8
entries pointing to 512K huge pte in 4k pages mode and 64 entries in
16k pages mode.
For 8M in 16k mode, a pgd entry have the below format
[<hugepte address >1101] . The hugepte table allocated will contain 8
entries pointing to 8M huge pte.
For 8M in 4k mode, multiple pgd entries point to the same hugepte
address and pgd entry will have the below format
[<hugepte address>1101]. The hugepte table allocated will only have one
entry.
For the time being, we do not support CPU15 ERRATA when HUGETLB is
selected
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> (v3, for the generic bits)
Signed-off-by: Scott Wood <oss@buserror.net>
Four fixes, the first for code we merged this cycle and three that are also
going to stable:
- On 64-bit Book3E we were not placing the .text section where we said we would
in the asm.
- We broke building the boot wrapper on some 32-bit toolchains.
- Lazy icache flushing was broken on pre-POWER5 machines.
- One of the error paths in our EEH code would lead to a deadlock.
Thanks to:
Andrew Donnellan, Ben Hutchings, Benjamin Herrenschmidt, Nicholas Piggin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6IL4
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Four fixes, the first for code we merged this cycle and three that are
also going to stable:
- On 64-bit Book3E we were not placing the .text section where we
said we would in the asm.
- We broke building the boot wrapper on some 32-bit toolchains.
- Lazy icache flushing was broken on pre-POWER5 machines.
- One of the error paths in our EEH code would lead to a deadlock.
Thanks to: Andrew Donnellan, Ben Hutchings, Benjamin Herrenschmidt,
Nicholas Piggin"
* tag 'powerpc-4.9-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64: Fix placement of .text to be immediately following .head.text
powerpc/eeh: Fix deadlock when PE frozen state can't be cleared
powerpc/mm: Fix lazy icache flush on pre-POWER5
powerpc/boot: Fix build failure in 32-bit boot wrapper
There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when a
module is being unloaded and before the text goes away and this code
grabs the ftrace_lock mutex and removes the module functions from the
ftrace list, such that it will no longer do any modifications to that
module's text, the update to make functions be traced or not is done
under the ftrace_lock mutex as well. And by now, __init section codes
should not been modified by ftrace, because it is black listed in
recordmcount.c and ignored by ftrace.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We are going to get rid of @current references in mmu_context_boos3s64.c
and cache mm_struct in the VFIO container. Since mm_context_t does not
have reference counting, we will be using mm_struct which does have
the reference counter.
This changes mm_iommu_init/mm_iommu_cleanup to receive mm_struct rather
than mm_context_t (which is embedded into mm).
This should not cause any behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current facility_strings[] are correct when the trap address is
0xf80 (hypervisor facility unavailable). When the trap address is
0xf60 (facility unavailable) IC (Interruption Cause) a.k.a status in the
code is undefined for values 0 and 1.
Add a check to prevent printing the (misleading) facility name for IC 0
and 1 when we came in via 0xf60. In all cases, print the actual IC
value, to avoid any confusion.
This hasn't been seen on real hardware, on only qemu which was
misreporting an exception.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[mpe: Fix indentation, combine printks(), massage change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Do not introduce any additional alignment. Placement of text section
will be set by fixed section macros. Without this, output section
alignment defaults to 4096, which makes BookE text section start at
0x1000 when it is expected to start at 0x100.
This was introduced by commit 57f266497d ("powerpc: Use gas sections
for arranging exception vectors") and was caught with the scripted head
section checker (not yet merged).
Fixes: 57f266497d ("powerpc: Use gas sections for arranging exception vectors")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In eeh_reset_device(), we take the pci_rescan_remove_lock immediately after
after we call eeh_reset_pe() to reset the PCI controller. We then call
eeh_clear_pe_frozen_state(), which can return an error. In this case, we
bail out of eeh_reset_device() without calling pci_unlock_rescan_remove().
Add a call to pci_unlock_rescan_remove() in the eeh_clear_pe_frozen_state()
error path so that we don't cause a deadlock later on.
Reported-by: Pradipta Ghosh <pradghos@in.ibm.com>
Fixes: 7895470063 ("powerpc/eeh: Avoid I/O access during PE reset")
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we've defined structures to describe each of the client
architecture vectors, we can use those to construct the value we pass to
firmware.
This avoids the tricks we previously played with the W() macro, allows
us to properly endian annotate fields, and should help to avoid bugs
introduced by failing to have the correct number of zero pad bytes
between fields.
It also means we can avoid hard coding IBM_ARCH_VEC_NRCORES_OFFSET in
order to update the max_cpus value and instead just set it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The "client architecture vectors" are a series of structures we pass to
firmware to define various things, such as what processors we support
and many other options.
Each structure is entirely different so we have to define a different
struct for each one, but that's OK.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This purgatory implementation is based on the versions from kexec-tools
and kexec-lite, with additional changes.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds the support code needed for implementing
kexec_file_load() on powerpc.
This consists of functions to load the ELF kernel, either big or little
endian, and setup the purgatory enviroment which switches from the first
kernel to the second kernel.
None of this code is built yet, as it depends on CONFIG_KEXEC_FILE which
we have not yet defined. Although we could define CONFIG_KEXEC_FILE in
this patch, we'd then have a window in history where the kconfig symbol
is present but the syscall is not, which would be awkward.
Signed-off-by: Josh Sklar <sklar@linux.vnet.ibm.com>
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit 2965faa5e0 ("kexec: split kexec_load syscall from kexec core
code") introduced CONFIG_KEXEC_CORE so that CONFIG_KEXEC means whether
the kexec_load system call should be compiled-in and CONFIG_KEXEC_FILE
means whether the kexec_file_load system call should be compiled-in.
These options can be set independently from each other.
Since until now powerpc only supported kexec_load, CONFIG_KEXEC and
CONFIG_KEXEC_CORE were synonyms. That is not the case anymore, so we
need to make a distinction. Almost all places where CONFIG_KEXEC was
being used should be using CONFIG_KEXEC_CORE instead, since
kexec_file_load also needs that code compiled in.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This converts one that was missed by b1576fec7f ("powerpc: No need
to use dot symbols when branching to a function").
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
From 80f23935ca ("powerpc: Convert cmp to cmpd in idle enter sequence"):
PowerPC's "cmp" instruction has four operands. Normally people write
"cmpw" or "cmpd" for the second cmp operand 0 or 1. But, frequently
people forget, and write "cmp" with just three operands.
With older binutils this is silently accepted as if this was "cmpw",
while often "cmpd" is wanted. With newer binutils GAS will complain
about this for 64-bit code. For 32-bit code it still silently assumes
"cmpw" is what is meant.
In this case, cmpwi is called for, so this is just a build fix for
new toolchains.
Cc: stable@vger.kernel.org # v3.0+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes marked for stable:
- Set missing wakeup bit in LPCR on POWER9 (Benjamin Herrenschmidt)
- Fix the early OPAL console wrappers (Oliver O'Halloran)
- Fixup kernel read only mapping (Aneesh Kumar K.V)
Fixes for code merged this cycle:
- Fix missing CRCs, add more asm-prototypes.h declarations (Nicholas Piggin)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=75sc
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Set missing wakeup bit in LPCR on POWER9
- Fix the early OPAL console wrappers
- Fixup kernel read only mapping
Fixes for code merged this cycle:
- Fix missing CRCs, add more asm-prototypes.h declarations"
* tag 'powerpc-4.9-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fixup kernel read only mapping
powerpc/boot: Fix the early OPAL console wrappers
powerpc: Fix missing CRCs, add more asm-prototypes.h declarations
powerpc: Set missing wakeup bit in LPCR on POWER9
Ensure that PSSCR is set to a safe value corresponding to no
state-loss each time a POWER9 CPU comes online.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-By: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 adds new capabilities to the tlbie (TLB invalidate entry)
and tlbiel (local tlbie) instructions. Both instructions get a
set of new parameters (RIC, PRS and R) which appear as bits in the
instruction word. The tlbiel instruction now has a second register
operand, which contains a PID and/or LPID value if needed, and
should otherwise contain 0.
This adapts KVM-HV's usage of tlbie and tlbiel to work on POWER9
as well as older processors. Since we only handle HPT guests so
far, we need RIC=0 PRS=0 R=0, which ends up with the same instruction
word as on previous processors, so we don't need to conditionally
execute different instructions depending on the processor.
The local flush on first entry to a guest in book3s_hv_rmhandlers.S
is a loop which depends on the number of TLB sets. Rather than
using feature sections to set the number of iterations based on
which CPU we're on, we now work out this number at VM creation time
and store it in the kvm_arch struct. That will make it possible to
get the number from the device tree in future, which will help with
compatibility with future processors.
Since mmu_partition_table_set_entry() does a global flush of the
whole LPID, we don't need to do the TLB flush on first entry to the
guest on each processor. Therefore we don't set all bits in the
tlb_need_flush bitmap on VM startup on POWER9.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This adds code to handle two new guest-accessible special-purpose
registers on POWER9: TIDR (thread ID register) and PSSCR (processor
stop status and control register). They are context-switched
between host and guest, and the guest values can be read and set
via the one_reg interface.
The PSSCR contains some fields which are guest-accessible and some
which are only accessible in hypervisor mode. We only allow the
guest-accessible fields to be read or set by userspace.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This merges in the ppc-kvm topic branch to get changes to
arch/powerpc code that are necessary for adding POWER9 KVM support.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Partially copied from commit df0698be14 ("ARM: stack protector:
change the canary value per task")
A new random value for the canary is stored in the task struct whenever
a new task is forked. This is meant to allow for different canary values
per task. On powerpc, GCC expects the canary value to be found in a global
variable called __stack_chk_guard. So this variable has to be updated
with the value stored in the task struct whenever a task switch occurs.
Because the variable GCC expects is global, this cannot work on SMP
unfortunately. So, on SMP, the same initial canary value is kept
throughout, making this feature a bit less effective although it is still
useful.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Partialy copied from commit c743f38013 ("ARM: initial stack protector
(-fstack-protector) support")
This is the very basic stuff without the changing canary upon
task switch yet. Just the Kconfig option and a constant canary
value initialized at boot time.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Invoke the kprobe handlers directly rather than through notify_die(), to
reduce path taken for handling kprobes. Similar to commit 6f6343f53d
("kprobes/x86: Call exception handlers directly from do_int3/do_debug").
While at it, rename post_kprobe_handler() to kprobe_post_handler() for
more uniform naming.
Reported-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Define and set the POWER9 HFSCR doorbell bit so that guests can use
msgsndp.
ISA 3.0 calls this MSGP, so name it accordingly in the code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
The previous convention of keeping the files around until the CPU is dead
has not been preserved as there is no point to keep them available when the
cpu is going down. This makes the hotplug call symmetric.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: rt@linuxtronix.de
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20161117183541.8588-17-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is the reasonable expectation that if an executable file is not
readable there will be no way for a user without special privileges to
read the file. This is enforced in ptrace_attach but if ptrace
is already attached before exec there is no enforcement for read-only
executables.
As the only way to read such an mm is through access_process_vm
spin a variant called ptrace_access_vm that will fail if the
target process is not being ptraced by the current process, or
the current process did not have sufficient privileges when ptracing
began to read the target processes mm.
In the ptrace implementations replace access_process_vm by
ptrace_access_vm. There remain several ptrace sites that still use
access_process_vm as they are reading the target executables
instructions (for kernel consumption) or register stacks. As such it
does not appear necessary to add a permission check to those calls.
This bug has always existed in Linux.
Fixes: v1.0
Cc: stable@vger.kernel.org
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
There is a new bit, LPCR_PECE_HVEE (Hypervisor Virtualization Exit
Enable), which controls wakeup from STOP states on Hypervisor
Virtualization Interrupts (which happen to also be all external
interrupts in host or bare metal mode).
It needs to be set or we will miss wakeups.
Fixes: 9baaef0a22 ("powerpc/irq: Add support for HV virtualization interrupts")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Rename it to HVEE to match the name in the ISA]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
eeh_pe_reset and eeh_reset_pe are two different functions in the same
file which do mostly the same thing. Not only is this confusing, but
potentially causes disrepancies in functionality, notably eeh_reset_pe
as it does not check return values for failure.
Refactor this into the following:
- eeh_pe_reset(): stays as is, performs a single operation, exported
- eeh_pe_reset_full(): new, full reset process that calls eeh_pe_reset()
- eeh_reset_pe(): removed and replaced by eeh_pe_reset_full()
- eeh_reset_pe_once(): removed
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PHB, PE (and by association MVE) numbers are printed as a mix of decimal
and hexadecimal throughout the kernel. This can be misleading, so make
them all hexadecimal.
Standardising on hex instead of dec because:
- PHB numbers are presented in hex in sysfs/debugfs (and lspci, etc)
- PE numbers are presented as hex in sysfs and parsed in hex in debugfs
The only place I think this could cause confusing are the messages during
boot, i.e.
pci 000a:01 : [PE# 000] Secondary bus 1 associated with PE#0
which can be a quick way to check PE numbers. pe_level_printk() will
only print two characters instead of three, so the above would be
pci 000a:01 : [PE# 00] Secondary bus 1 associated with PE#0
which gives a hint it's in hex.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When switching from/to a guest that has a transaction in progress,
we need to save/restore the checkpointed register state. Although
XER is part of the CPU state that gets checkpointed, the code that
does this saving and restoring doesn't save/restore XER.
This fixes it by saving and restoring the XER. To allow userspace
to read/write the checkpointed XER value, we also add a new ONE_REG
specifier.
The visible effect of this bug is that the guest may see its XER
value being corrupted when it uses transactions.
Fixes: e4e3812150 ("KVM: PPC: Book3S HV: Add transactional memory support")
Fixes: 0a8eccefcb ("KVM: PPC: Book3S HV: Add missing code for transaction reclaim on guest exit")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Fixes marked for stable:
- Fix system reset interrupt winkle wakeups (Nicholas Piggin)
- Fix setting of AIL in hypervisor mode (Benjamin Herrenschmidt)
Fixes for code merged this cycle:
- Fix exception vector build with 2.23 era binutils (Hugh Dickins)
- Fix missing update of HID register on secondary CPUs (Aneesh Kumar K.V)
Other:
- Fix missing pr_cont()s in show_stack() (Michael Ellerman)
- Fix missing pr_cont()s in print_msr_bits() et. al. (Michael Ellerman)
- Fix missing pr_cont()s in show_regs() (Michael Ellerman)
- Fix missing pr_cont()s in instruction dump (Andrew Donnellan)
- Invalidate ERAT on tlbiel for POWER9 DD1 (Michael Neuling)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+6XC
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- fix system reset interrupt winkle wakeups
- fix setting of AIL in hypervisor mode
Fixes for code merged this cycle:
- fix exception vector build with 2.23 era binutils
- fix missing update of HID register on secondary CPUs
Other:
- fix missing pr_cont()s
- invalidate ERAT on tlbiel for POWER9 DD1"
* tag 'powerpc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix missing update of HID register on secondary CPUs
powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1
powerpc/64: Fix setting of AIL in hypervisor mode
powerpc/oops: Fix missing pr_cont()s in instruction dump
powerpc/oops: Fix missing pr_cont()s in show_regs()
powerpc/oops: Fix missing pr_cont()s in print_msr_bits() et. al.
powerpc/oops: Fix missing pr_cont()s in show_stack()
powerpc: Fix exception vector build with 2.23 era binutils
powerpc/64s: Fix system reset interrupt winkle wakeups
The ibm_pa_features array consists of structures that describe which bit
and byte in the ibm,pa-features property toggles one or more flags in
either the CPU, MMU, or user visible feature flags.
Each one consists of 7 values, which are all unsigned long, int or char,
meaning the compiler gives us no warning if we assign the wrong values
to the wrong elements. In fact we have had a bug here in the past, where
we were setting incorrect bits, see commit 6997e57d69 ("powerpc:
scan_features() updates incorrect bits for REAL_LE").
So switch to using named initialisers for the structure elements, to
reduce the likelihood of future bugs, and hopefully improve readability
also.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
When ending an oops, don't clear die_owner unless the nest count
went to zero. This prevents a second nested oops from hanging forever
on the die_lock.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When exiting xmon with 'x' (exit and recover), oops_begin bails
out immediately, but die then calls __die() and oops_end(), which
cause a lot of bad things to happen.
If the debugger was attached then went to graceful recovery, exit
from die() immediately.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the unused but set variable srr1 in save_mce_event() to
fix the following GCC warning when building with 'W=1':
arch/powerpc/kernel/mce.c:75:11: warning: variable 'srr1' set but not used
It has never been used.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix two [-Wold-style-declaration] GCC warnings by moving the inline
keyword before the return type.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Commit d3cbff1b5 "powerpc: Put exception configuration in a common place"
broke the setting of the AIL bit (which enables taking exceptions with
the MMU still on) on all processors, moving it incorrectly to a function
called only on the boot CPU. This was correct for the guest case but
not when running in hypervisor mode.
This fixes it by partially reverting that commit, putting the setting
back in cpu_ready_for_interrupts()
Fixes: d3cbff1b5a ("powerpc: Put exception configuration in a common place")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Only s390 and powerpc have hardware facilities allowing to measure
cputimes scaled by frequency. On all other architectures
utimescaled/stimescaled are equal to utime/stime (however they are
accounted separately).
Remove {u,s}timescaled accounting on all architectures except
powerpc and s390, where those values are explicitly accounted
in the proper places.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161031162143.GB12646@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since commit:
cf9efce0ce ("powerpc: Account time using timebase rather than PURR")
cputime_last_delta is not initialized to other value than 0, hence it's
not used except zero check and cputime_to_scaled() just returns
the argument.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1479175612-14718-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
