The polarity of the over current detection pin isn't configured on i.MX6/7
if it's unspecified in the device tree. So the actual configuration depends
on bootloader behavior which is bad.
So encourage users to fix their device tree by issuing a warning in this
case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The status quo on i.MX6 is that if "over-current-active-high" is
specified in the device tree this is configured as expected. If
the property is missing polarity isn't changed and so the
polarity is kept as setup by the bootloader. Reset default is
active high, so active low can only be used with help by the
bootloader. On i.MX7 it is similar, but there disabling of
over current detection has a similar inconsistency.
This patch introduces a new property that allows to explicitly
configure for active low over current detection and consistently
sets this up. In the absence of an explicit configuration the
bit is kept as is. On i.MX7 over current detection is used unless
disabled in the device tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The chipidea controller has some special requirements during
suspend/resume, override common ehci->hub_control to implement
it.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
To support imx HSIC, there are some special requirement:
- The HSIC pad is 1.2v, it may need to supply from external
- The data/strobe pin needs to be pulled down first, and after
host mode is initialized, the strobe pin needs to be pulled up
- During the USB suspend/resume, special setting is needed
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
NXP (Freecale) imx HSIC design has some special requirements, add
some flags at host code to handle them.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In stream mode, when fast-forwarding TRBs, the stream number
is not cleared causing the new stream to not get assigned. So
we don't want controller to carry on transfers when short packet
is received. So disable the CSP for stream capable endpoint.
This is based on the 3.30a Programming guide, where table 3-1
device descriptor structure field definitions says for CSP bit
If this bit is 0, the controller generates an XferComplete event
and remove the stream. So if we keep CSP as 1 then switching between
streams would not happen as in stream mode, when fast-forwarding
TRBs, the stream number is not cleared causing the new stream to not get
assigned.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/mos7840.c: In function 'mos7840_send_cmd_write_baud_rate':
drivers/usb/serial/mos7840.c:1584:16: warning:
variable 'number' set but not used [-Wunused-but-set-variable]
drivers/usb/serial/mos7840.c: In function 'mos7840_change_port_settings':
drivers/usb/serial/mos7840.c:1695:21: warning:
variable 'serial' set but not used [-Wunused-but-set-variable]
'number' never used since introduction in commit 3f5429746d ("USB: Moschip
7840 USB-Serial Driver")
'serial' not used since commit 5833041f1b ("USB: serial: remove unnecessary
reinitialisations of urb->dev")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Disable power_down by setting the parameter to
DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
Meson SoCs where USB devices are only recognized when plugged in before
booting Linux. A hot-plugged USB device was not detected even though the
device got power (my USB thumb drive for example has an LED which lit
up).
A similar fix was implemented for Rockchip SoCs in commit c216765d3a
("usb: dwc2: disable power_down on rockchip devices"). That commit
suggests that a change in the dwc2 driver is the cause because the
default value for the "hibernate" parameter (which then got renamed to
"power_down" to support other modes) was changed in the v4.17 merge
window with:
commit 6d23ee9caa ("Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing").
Cc: <stable@vger.kernel.org> # 4.19
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Suggested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Refactoring, no functional changes.
But worth mentioning that checking for port link resume state is now behind
a additional port power check.
This is fine as ports can't be in resume state if port power bit is not
set.
xhci spec section 4.19.1.1.6 figure 34 shows that port power bit must be
set for all 'Enable' substates, including U0,U1,U2,U3 (suspended), Resume,
and RExit states.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move U0 link state handing to USB3 and USB2 specific functions
Note that
bus_state->resuming_ports:
bus_state->resume_done[]:
are only used for USB2, and don't need to cleared for USB3 ports
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Group the code where the wPortstatus and wPortChange bits
are set into one place.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mostly refactoring, with the exception that USB_PORT_STAT_L1 link state
is reported if xhci port link is in U2 AND port is powered.
Previously we did not check if the port was powered, but according to
xhci spec 4.19.1.1.6 All the 'Enabled' states, including
USB_PORT_STAT_L1 (U2), U1, U0 and U3 must have Port power bit set.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that each root hub has their own bus_state strucure the
hcd_undex() used to get the correct bus_state strucure is
no longer needed.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the bus_state structure under struct usb_hub.
We need a bus_state strucure for each roothub to keep track of suspend
related info for each port.
Instead of keeping an array of two bus_state structures right under
struct xhci, it makes more sense move them to the xhci_hub structure.
No functional changes.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is introduced for the pre-0.96 xHC controllers, and the driver only
support HW LPM for 1.0 and later controllers.It's not actually used now
and is thought not to be used in the future any more, so just remove it.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 211f658b7b ("usb: dwc3: pci: Use devm functions to get
the phy GPIOs") changed the code to claim the PHY GPIOs permanently
for Intel Baytrail devices.
This causes issues when the actual PHY driver attempts to claim the
same GPIO descriptors. For example, tusb1210 now fails to probe with:
tusb1210: probe of dwc3.0.auto.ulpi failed with error -16 (EBUSY)
dwc3-pci needs to turn on the PHY once before dwc3 is loaded, but
usually the PHY driver will then hold the GPIOs to turn off the
PHY when requested (e.g. during suspend).
To fix the problem, this reverts the commit to restore the old
behavior to put the GPIOs immediately after usage.
Link: https://www.spinics.net/lists/linux-usb/msg174681.html
Cc: stable@vger.kernel.org
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/mtu3/mtu3_qmu.c: In function 'qmu_tx_zlp_error_handler':
drivers/usb/mtu3/mtu3_qmu.c:385:22: warning:
variable 'req' set but not used [-Wunused-but-set-variable]
It seems dbginfo original intention is print 'req' other than 'mreq'
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The missed break statement in the outer switch makes the code fall through
always and thus always same value will be printed.
Besides that, compiler warns about missed fall through marker:
drivers/usb/dwc3/./trace.h: In function ‘trace_raw_output_dwc3_log_trb’:
drivers/usb/dwc3/./trace.h:246:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (pcm) {
^~~~~~
Add the missing break statement to work correctly without compilation
warnings.
Fixes: fa8d965d73 ("usb: dwc3: trace: pretty print high-bandwidth transfers too")
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here's a fix for a reported USB-console regression in 4.18 which
revealed a long-standing bug in the console implementation.
The patch has been in linux-next over night with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXAlOXAAKCRALxc3C7H1l
COC9AP4jozobKxNIgbmP6LAwz34Zv19qZyhi2hOzM0Less5o+QD+PLKS4yFPErNq
L6jm+cb1RE3rW9bjrbphoT7PvQoa3QM=
=QA9N
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fix for v4.20-rc6
Here's a fix for a reported USB-console regression in 4.18 which
revealed a long-standing bug in the console implementation.
The patch has been in linux-next over night with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: console: fix reported terminal settings
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f0 ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The spinlock was inside the urb completion function which is only
called once per display and is then resubmitted from this function.
There was no other place where this lock was used.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does allocate a DMA address with usb_alloc_coherent but did
not set the appropriate flag to signal that transfer_dma is set to a
valid value.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot and KASAN found the following invalid-free bug in
port_over_current_notify():
--------------------------------------------------------------------------
BUG: KASAN: double-free or invalid-free in port_over_current_notify
drivers/usb/core/hub.c:5192 [inline]
BUG: KASAN: double-free or invalid-free in port_event
drivers/usb/core/hub.c:5241 [inline]
BUG: KASAN: double-free or invalid-free in hub_event+0xd97/0x4140
drivers/usb/core/hub.c:5384
CPU: 1 PID: 32710 Comm: kworker/1:3 Not tainted 4.20.0-rc3+ #129
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256
kasan_report_invalid_free+0x64/0xa0 mm/kasan/report.c:336
__kasan_slab_free+0x13a/0x150 mm/kasan/kasan.c:501
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kfree+0xcf/0x230 mm/slab.c:3817
port_over_current_notify drivers/usb/core/hub.c:5192 [inline]
port_event drivers/usb/core/hub.c:5241 [inline]
hub_event+0xd97/0x4140 drivers/usb/core/hub.c:5384
process_one_work+0xc90/0x1c40 kernel/workqueue.c:2153
worker_thread+0x17f/0x1390 kernel/workqueue.c:2296
kthread+0x35a/0x440 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
--------------------------------------------------------------------------
The problem is caused by use of a static array to store
environment-string pointers. When the routine is called by multiple
threads concurrently, the pointers from one thread can overwrite those
from another.
The solution is to use an ordinary automatic array instead of a static
array.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+98881958e1410ec7e53c@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add another Apple Cinema Display to the list of supported displays.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we are going to use the same in Designware USB 3 driver,
rename the property to be consistent across the drivers.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the new frame_number API to report the isochronous interval
frame number. This patch checks and reports the interval in which the
isoc transfer was transmitted or received via the Isoc-First TRB SOF
number field.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When the controller supports SS mode, but works as HS mode, the
SOFTCONN will not be cleared automatically when clear USB3_EN
by default, this cause an issue that can't disconnect from host,
so clear SOFTCONN when clear USB3_EN when the class driver want
to disable the D+ pullup.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the controller receives a new SETUP during SETUP data stage,
and will generate SETUPENDISR interrupt, the driver should abort
the current SETUP command and process the new one.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the issue: device doesn't accept LGO_U1/U2:
1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2
by default;
2. enable/disable controller to initiate requests for transition into
U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable hardware remote wakeup from L1 automatically based on the FIFO
status, instead of manual way.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The QMU checksum calculation is redundant, mostly used by debug,
so remove it here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally, when dr_mode is USB_DR_MODE_HOST, it didn't power down device ip,
so host ip sleep will fail at ssusb_host_disable.
Power down device ip at ssusb_host_setup.
Signed-off-by: Hsin-Yi, Wang <hsinyi@chromium.org>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify the wait delay utilize the high resolution timer API to allow for
more precisely scheduled callbacks.
A previous commit added a 1ms retry delay after multiple consecutive
NAKed transactions using jiffies. On systems with a low timer interrupt
frequency, this delay may be significantly longer than specified,
resulting in misbehavior with some USB devices.
This scenario was reached on a Raspberry Pi 3B with a Macally FDD-USB
floppy drive (identified as 0424:0fdc Standard Microsystems Corp.
Floppy, based on the USB97CFDC USB FDC). With the relay delay, the drive
would be unable to mount a disk, replying with NAKs until the device was
reset.
Using ktime, the delta between starting the timer (in dwc2_hcd_qh_add)
and the callback function can be determined. With the original delay
implementation, this value was consistently approximately 12ms. (output
in us).
<idle>-0 [000] ..s. 1600.559974: dwc2_wait_timer_fn: wait_timer delta: 11976
<idle>-0 [000] ..s. 1600.571974: dwc2_wait_timer_fn: wait_timer delta: 11977
<idle>-0 [000] ..s. 1600.583974: dwc2_wait_timer_fn: wait_timer delta: 11976
<idle>-0 [000] ..s. 1600.595974: dwc2_wait_timer_fn: wait_timer delta: 11977
After converting the relay delay to using a higher resolution timer, the
delay was much closer to 1ms.
<idle>-0 [000] d.h. 1956.553017: dwc2_wait_timer_fn: wait_timer delta: 1002
<idle>-0 [000] d.h. 1956.554114: dwc2_wait_timer_fn: wait_timer delta: 1002
<idle>-0 [000] d.h. 1957.542660: dwc2_wait_timer_fn: wait_timer delta: 1004
<idle>-0 [000] d.h. 1957.543701: dwc2_wait_timer_fn: wait_timer delta: 1002
The floppy drive operates properly with delays up to approximately 5ms,
and sends NAKs for any delays that are longer.
Fixes: 38d2b5fb75 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Terin Stock <terin@terinstock.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When initializing a hub we want to give a USB3 port in link training
the same debounce delay time before autosuspening the hub as already
trained, connected enabled ports.
USB3 ports won't reach the enabled state with "current connect status" and
"connect status change" bits set until the USB3 link training finishes.
Catching the port in link training (polling) and adding the debounce delay
prevents unnecessary failed attempts to autosuspend the hub.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the controller supports SS mode, but works as HS mode, the
SOFTCONN will not be cleared automatically when clear USB3_EN
by default, this cause an issue that can't disconnect from host,
so clear SOFTCONN when clear USB3_EN when the class driver want
to disable the D+ pullup.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If the controller receives a new SETUP during SETUP data stage,
and will generate SETUPENDISR interrupt, the driver should abort
the current SETUP command and process the new one.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix the issue: device doesn't accept LGO_U1/U2:
1. set SW_U1/U2_ACCEPT_ENABLE to eanble controller to accept LGO_U1/U2
by default;
2. enable/disable controller to initiate requests for transition into
U1/U2 by SW_U1/U2_REQUEST_ENABLE instead of SW_U1/U2_ACCEPT_ENABLE;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable hardware remote wakeup from L1 automatically based on the FIFO
status, instead of manual way.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The QMU checksum calculation is redundant, mostly used by debug,
so remove it here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Originally, when dr_mode is USB_DR_MODE_HOST, it didn't power down device ip,
so host ip sleep will fail at ssusb_host_disable.
Power down device ip at ssusb_host_setup.
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Hsin-Yi, Wang <hsinyi@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Power down feature of DWC2 module integrated in Samsung SoCs doesn't work
properly or needs some additional handling in PHY or SoC glue layer, so
disable it for now. Without disabling power down, DWC2 causes random memory
trashes and fails enumeration if there is no USB link to host on driver
probe.
Fixes: 03ea6d6e9e ("usb: dwc2: Enable power down")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Availability of TRB's is calculated using dwc3_calc_trbs_left(), which
determines total available TRB's based on the HWO bit set in a TRB.
In the present code, __dwc3_prepare_one_trb() is called with a TRB which
needs to be prepared for transfer. This __dwc3_prepare_one_trb() calls
dwc3_calc_trbs_left() to determine total available TRBs and set IOC bit
if the total available TRBs are zero. Since the present working TRB (which
is passed as an argument to __dwc3_prepare_one_trb() ) doesn't yet have
the HWO bit set before calling dwc3_calc_trbs_left(), there are chances
that dwc3_calc_trbs_left() wrongly calculates this present working TRB
as free(since the HWO bit is not yet set) and returns the total available
TRBs as greater than zero (including the present working TRB). This could
be a problem.
This patch corrects the above mentioned problem in __dwc3_prepare_one_trb()
by increementing the dep->trb_enqueue at the last (after preparing the TRB)
instead of increementing at the start and setting the IOC bit only if the
total available TRBs returned by dwc3_calc_trbs_left() is 1 . Since we are
increementing the dep->trb_enqueue at the last, the present working TRB is
also considered as available by dwc3_calc_trbs_left() and non zero value is
returned . So, according to the modified logic, when the total available
TRBs is equal to 1 that means the total available TRBs in the pool are 0.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The stream capable endpoints require stream id to be given
when issuing START TRANSFER. While issuing no-op trb the
stream id is not yet known, so don't issue no-op trb's on
stream capable endpoints.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For stream capable endpoints, stream id related information
needs to be updated into DEPCMD while issuing START TRANSFER.
This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a new PID 0x7843 to the driver.
Let the new products be able to set up 3 serial ports with the driver.
Note that this depends on e8603076f5 ("USB: serial: mos7840: clean up
register handling").
Signed-off-by: JackyChou <jackychou@asix.com.tw>
[ johan: mention dependency in case anyone wants to backport this ]
Signed-off-by: Johan Hovold <johan@kernel.org>
In the read/write function, set port 2 independently in the 2-port case.
When setting the offset of port registers, the offset between port 1 and
other ports is different, so port 1 is set independently.
Then in the rest of ports, the port 2 between 2-ports case and 4-ports case
is different, so port 2 in 2-ports case is set independently.
Specifically, port 2 in the 2-port case maps to the registers used by
port 3 in the 4-port case.
Signed-off-by: JackyChou <jackychou@asix.com.tw>
[ johan: simplify register-offset handling at port probe, add a comment
and amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The ACPI device with INT3515 _HID is representing a complex USB PD
hardware infrastructure which includes several I2C slave ICs.
We add an ID to the I2C multi instantiate list to enumerate
all I2C slaves correctly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In this second set of fixes for the current -rc cycle, we have some
regressions fixes for the old omap_udc driver done by Aaro Koskinen.
We're also reverting an old patch on dwc3 which is, now, known to
break USB certification in some cases.
We have a fix on u_ether for an unsafe list iteration.
-----BEGIN PGP SIGNATURE-----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=MIKU
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v4.20-rc4
In this second set of fixes for the current -rc cycle, we have some
regressions fixes for the old omap_udc driver done by Aaro Koskinen.
We're also reverting an old patch on dwc3 which is, now, known to
break USB certification in some cases.
We have a fix on u_ether for an unsafe list iteration.
* tag 'fixes-for-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: gadget: u_ether: fix unsafe list iteration
USB: omap_udc: fix rejection of out transfers when DMA is used
USB: omap_udc: fix USB gadget functionality on Palm Tungsten E
USB: omap_udc: fix omap_udc_start() on 15xx machines
USB: omap_udc: fix crashes on probe error and module removal
USB: omap_udc: use devm_request_irq()
Revert "usb: dwc3: gadget: skip Set/Clear Halt when invalid"
iscsi_target_mod is the only LIO fabric where fabric_ops.name differs from
the fabric_ops.fabric_name string. fabric_ops.name is used when matching
target/$fabric ConfigFS create paths, so rename it .fabric_alias and
fallback to target/$fabric vs .fabric_name comparison if .fabric_alias
isn't initialised. iscsi_target_mod is the only fabric module to set
.fabric_alias . All other fabric modules rely on .fabric_name matching and
can drop the duplicate string.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All fabrics return a const string. In all cases *except* iSCSI the
get_fabric_name() string matches fabric_ops.name.
Both fabric_ops.get_fabric_name() and fabric_ops.name are user-facing, with
the former being used for PR/ALUA state and the latter for ConfigFS
(config/target/$name), so we unfortunately need to keep both strings around
for now. Replace the useless .get_fabric_name() accessor function with a
const string fabric_name member variable.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
list_for_each_entry_safe() is not safe for deleting entries from the
list if the spin lock, which protects it, is released and reacquired during
the list iteration. Fix this issue by replacing this construction with
a simple check if list is empty and removing the first entry in each
iteration. This is almost equivalent to a revert of the commit mentioned in
the Fixes: tag.
This patch fixes following issue:
--->8---
Unable to handle kernel NULL pointer dereference at virtual address 00000104
pgd = (ptrval)
[00000104] *pgd=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 1 PID: 84 Comm: kworker/1:1 Not tainted 4.20.0-rc2-next-20181114-00009-g8266b35ec404 #1061
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events eth_work
PC is at rx_fill+0x60/0xac
LR is at _raw_spin_lock_irqsave+0x50/0x5c
pc : [<c065fee0>] lr : [<c0a056b8>] psr: 80000093
sp : ee7fbee8 ip : 00000100 fp : 00000000
r10: 006000c0 r9 : c10b0ab0 r8 : ee7eb5c0
r7 : ee7eb614 r6 : ee7eb5ec r5 : 000000dc r4 : ee12ac00
r3 : ee12ac24 r2 : 00000200 r1 : 60000013 r0 : ee7eb5ec
Flags: Nzcv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 6d5dc04a DAC: 00000051
Process kworker/1:1 (pid: 84, stack limit = 0x(ptrval))
Stack: (0xee7fbee8 to 0xee7fc000)
...
[<c065fee0>] (rx_fill) from [<c0143b7c>] (process_one_work+0x200/0x738)
[<c0143b7c>] (process_one_work) from [<c0144118>] (worker_thread+0x2c/0x4c8)
[<c0144118>] (worker_thread) from [<c014a8a4>] (kthread+0x128/0x164)
[<c014a8a4>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xee7fbfb0 to 0xee7fbff8)
...
---[ end trace 64480bc835eba7d6 ]---
Fixes: fea14e68ff ("usb: gadget: u_ether: use better list accessors")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Gadget driver may take an unbounded amount of time to queue requests
after XferNotReady. This is important for isochronous endpoints which
need to be started for a specific (micro-)frame.
If we fail to start a transfer for isochronous endpoint, let's try
queueing to a future interval and see if that helps. We will stop trying
if we fail a start transfer for 5 intervals in the future.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 387f869d25 ("usb: gadget: u_ether: conditionally align
transfer size") started aligning transfer size only if requested,
breaking omap_udc DMA mode. Set quirk_ep_out_aligned_size to restore
the old behaviour.
Fixes: 387f869d25 ("usb: gadget: u_ether: conditionally align transfer size")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On Palm TE nothing happens when you try to use gadget drivers and plug
the USB cable. Fix by adding the board to the vbus sense quirk list.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On OMAP 15xx machines there are no transceivers, and omap_udc_start()
always fails as it forgot to adjust the default return value.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We currently crash if usb_add_gadget_udc_release() fails, since the
udc->done is not initialized until in the remove function.
Furthermore, on module removal the udc data is accessed although
the release function is already triggered by usb_del_gadget_udc()
early in the function.
Fix by rewriting the release and remove functions, basically moving
all the cleanup into the release function, and doing the completion
only in the module removal case.
The patch fixes omap_udc module probe with a failing gadged, and also
allows the removal of omap_udc. Tested by running "modprobe omap_udc;
modprobe -r omap_udc" in a loop.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current code fails to release the third irq on the error path
(observed by reading the code), and we get also multiple WARNs with
failing gadget drivers due to duplicate IRQ releases. Fix by using
devm_request_irq().
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Running out of requests on isochronous endpoints is part of normal
operation. We don't really need to know about it every time it
happens.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
They are much more useful in hexadecimal than in decimal. Moreover,
generic commands are already logged in hex.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Sometimes, errors happen when kicking transfers from
__dwc3_gadget_start_isoc(). In those cases, we need to pass along the
error so gadget driver can make informed decisions.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cherry G230 Stream 2.0 (G85-231) and 3.0 (G85-232) need this quirk to
function correctly. This fixes a but where double pressing numlock locks
up the device completely with need to replug the keyboard.
Signed-off-by: Michael Niewöhner <linux@mniewoehner.de>
Tested-by: Michael Niewöhner <linux@mniewoehner.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two new Realtek card readers require ums-realtek to work
correctly.
Add the new IDs to support them.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have a list of cancelled requests, we can skip over TRBs
when END_TRANSFER command completes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Whenever we have a request in flight, we can move it to the cancelled
list and later simply iterate over that list and skip over any TRBs we
find.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Extract the logic for skipping over TRBs to its own function. This
makes the code slightly more readable and makes it easier to move this
call to its final resting place as a following patch.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we track how many TRBs a request uses, it's easier to skip
over them in case of a call to usb_ep_dequeue(). Let's do so and
simplify the code a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Both flags are used for the same purpose in dwc3: appending an extra
TRB at the end to deal with controller requirements. By combining both
flags into one, we make it clear that the situation is the same and
that they should be treated equally.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DWC_usb31 version 1.70a-ea06 and prior, for highspeed and fullspeed
isochronous IN, BIT[15:14] of the 16-bit microframe number reported by
the XferNotReady event are invalid. The driver uses this number to
schedule the isochronous transfer and passes it to the START TRANSFER
command. Because this number is invalid, the command may fail. If
BIT[15:14] matches the internal 16-bit microframe, the START TRANSFER
command will pass and the transfer will start at the scheduled time, if
it is off by 1, the command will still pass, but the transfer will start
2 seconds in the future. For all other conditions, the START TRANSFER
command will fail with bus-expiry.
In order to workaround this issue, we can test for the correct
combination of BIT[15:14] by sending START TRANSFER commands with
different values of BIT[15:14]: 'b00, 'b01, 'b10, and 'b11. Each
combination is 2^14 uframe apart (or 2 seconds). 4 seconds into the
future will result in a bus-expiry status. As the result, within the 4
possible combinations for BIT[15:14], there will be 2 successful and 2
failure START COMMAND status. One of the 2 successful command status
will result in a 2-second delay start. The smaller BIT[15:14] value is
the correct combination.
Since there are only 4 outcomes and the results are ordered, we can
simply test 2 START TRANSFER commands with BIT[15:14] combinations 'b00
and 'b01 to deduce the smaller successful combination.
Let test0 = test status for combination 'b00 and test1 = test status for
'b01 of BIT[15:14]. The correct combination is as follow:
if test0 fails and test1 passes, BIT[15:14] is 'b01
if test0 fails and test1 fails, BIT[15:14] is 'b10
if test0 passes and test1 fails, BIT[15:14] is 'b11
if test0 passes and test1 passes, BIT[15:14] is 'b00
Synopsys STAR 9001202023: Wrong microframe number for isochronous IN
endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a new field to dwc3 structure to track VERSIONTYPE. The VERSIONTYPE
is represented in ASCII in the 32-bit VERSIONTYPE register. In
DWC_usb31, sub releases for each version are tracked with VERSIONTYPE
such as "ea01" and "ea02".
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some protocols implemented in userspace with FunctionFS might require large
buffers, e.g. 64kB or more. Currently the said memory is allocated with
kmalloc, which might fail should system memory be highly fragmented.
On the other hand, some UDC hardware allows scatter-gather operation and
this patch takes advantage of this capability: if the requested buffer
is larger than PAGE_SIZE and the UDC allows scatter-gather operation, then
the buffer is allocated with vmalloc and a scatterlist describing it is
created and passed to usb request.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Nothing to remap, only check length.
Define a minimal structure for CCID descriptor only used to check length.
As this descriptor shares the same value as HID descriptors, keep track and
compare current interface's class to expected HID and CCID standard values.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistake in comment
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The vb2_ops structure can be const as it is only stored in the ops
field of a vb2_queue structure and this field is const.
Done with the help of Coccinelle.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Set GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG register
to accept LPM token during ISOC transfers when TxFIFO is
not empty.
- Added two definitions.
#define GLPMCFG_LPM_ACCEPT_CTRL_CONTROL BIT(21)
#define GLPMCFG_LPM_ACCEPT_CTRL_ISOC BIT(22)
This patch uses GLPMCFG_LPM_ACCEPT_CTRL_ISOC.
GLPMCFG_LPM_ACCEPT_CTRL_CONTROL is defined for further use.
- Added setting GLPMCFG_LPM_ACCEPT_CTRL_ISOC bit in GLPMCFG
register in dwc2_gadget_init_lpm function.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to the databook DCTL_RMTWKUPSIG bit
is defined in DCTL register not in DCFG.
Updated setting DCTL_RMTWKUPSIG bit to DCTL
register.
Fixes: 187c5298a1 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC_usb31 and DWC_usb3 v3.30a and higher do not support OTG mode. If
the controller supports DRD but the dr_mode is not specified or set to
OTG, then set the mode to peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds a safety connection way for "forced_b_device" with
"workaround_for_vbus" like below:
< Example for R-Car E3 Ebisu >
# modprobe <any usb gadget driver>
# echo 1 > /sys/kernel/debug/ee020000.usb/b_device
(connect a usb cable to host side.)
# echo 2 > /sys/kernel/debug/ee020000.usb/b_device
Previous code should have connected a usb cable before the "b_device"
is set to 1 on the Ebisu board. However, if xHCI driver on the board
is probed, it causes some troubles:
- Conflicts USB VBUS/signals between the board and another host.
- "Cannot enable. Maybe the USB cable is bad?" might happen on
both the board and another host with a usb hub.
- Cannot enumerate a usb gadget correctly because an interruption
of VBUS change happens unexpectedly.
Reported-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allow extcon device, found by name, to provide DR status for USB.
This is needed, for example, in case of Intel Merrifield platform,
where the Intel Basin Cove PMIC provides an extcon device to communicate
the detected role.
Note, that the "linux,extcon-name" property name is only for kernel
internal use by X86/ACPI platform code and as such is not documented
in the device tree bindings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Switch to device property for 'extcon' handling.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's not very useful to repeat a bunch of probe deferral errors. And
it's also not very useful to log "failed" without telling the error
code.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The usb_gadget_ops structure can be const as it is only stored in
the ops field of a usb_gadget structure and this field is const.
Done with the help of Coccinelle.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support the option to disable USB2 LPM. Set xhci "usb2-lpm-disable"
property via "snps,usb2-lpm-disable" property.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
GUSB2PHYCFG.ENBLSLPM enables the controller to assert low power signals
to the PHY. Unless disabled via device property, explicitly set
GUSB2PHYCFG.ENBLSLPM as it may not be set by default.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Current implementation only prints/sets the link state for peripheral
mode only. Check and prevent printing bogus link state if the current
mode of operation is not peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Highspeed device and below has different state names than superspeed and
higher. Add proper checks and printouts of link states for highspeed and
below.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To dump internal LSP and endpoint state debug registers, we must write
to GDBGLSPMUX register. This patch correctly dump LSP and endpoint
states from the debug registers.
If the controller is in device mode, all LSP and endpoint state
registers will be dumped via the debugfs attribute "lsp_dump". In host
mode, the user has to write the LSP number to "lsp_dump" to dump a
specific LSP selection.
Fixes: 80b776340c ("usb: dwc3: Dump LSP and BMU debug info")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
TxFIFO and RxFIFO from GDBGFIFOSPACE are fifo depths in MDWIDTH. Convert
them into bytes for easier read.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Tx/RxFIFO types in the GDBGFIFOSPACE.FIFO_QUEUE_SELECT are not
queue. Properly rename them.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit ffb80fc672.
Turns out that commit is wrong. Host controllers are allowed to use
Clear Feature HALT as means to sync data toggle between host and
periperal.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a hunk of code that is indented too much by one level, fix
this by removing the extraneous tabs.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a missing indentation before the return statement. Add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve baud-rate generation by using rounding-to-closest instead of
truncation in divisor calculation.
Results have been verified by logic analyzer on an FT232RT (232BM) chip.
The following table shows the wanted baud rate, the baud rate obtained
with the old method (truncation), with the new method (rounding) and the
baud rate generated by the windows 10 driver. The numbers in parentheses
is the error.
+- Wanted --+------ Old -------+------ New -------+------ Win -------+
| 9600 | 9600 (0.00%) | 9604 (0.05%) | 9605 (0.05%) |
| 19200 | 19200 (0.00%) | 19199 (0.01%) | 19198 (0.01%) |
| 38400 | 38395 (0.01%) | 38431 (0.08%) | 38394 (0.02%) |
| 57600 | 57725 (0.22%) | 57540 (0.10%) | 57673 (0.13%) |
| 115200 | 115307 (0.09%) | 115330 (0.11%) | 115320 (0.10%) |
| 921600 | 919963 (0.18%) | 920386 (0.13%) | 920810 (0.09%) |
| 961200 | 996512 (3.67%) | 956480 (0.49%) | 956937 (0.44%) |
+-----------+------------------+------------------+------------------+
The error due to noise in the measurements is in the order of a few
tenths of a %. As can be seen, the baud rate is significantly improved
for some rates (e.g. 961200), and corresponds to the output given by the
windows driver.
The theoretical baud rate has been calculated for all baud rates from 1
to 3M, and as expected, the error is centered around 0, with a triangle
shape instead of a sawtooth, so the maximum error is decreased to half.
Signed-off-by: Nikolaj Fogh <nikolajfogh@gmail.com>
[ johan: edit commit message slightly ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Here are a number of small USB fixes for 4.20-rc4.
There's the usual xhci and dwc2/3 fixes as well as a few minor other
issues resolved for problems that have been reported. Full details are
in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW/ZsOg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymPlACeO1ii05UG6Mb47AC0sZbgMk5diWwAnRK3A0Pe
fSupZy5v6u1HBEormFco
=5k0S
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.20-rc4.
There's the usual xhci and dwc2/3 fixes as well as a few minor other
issues resolved for problems that have been reported. Full details are
in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: cdc-acm: add entry for Hiro (Conexant) modem
usb: xhci: Prevent bus suspend if a port connect change or polling state is detected
usb: core: Fix hub port connection events lost
usb: dwc3: gadget: fix ISOC TRB type on unaligned transfers
Revert "usb: gadget: ffs: Fix BUG when userland exits with submitted AIO transfers"
usb: dwc2: pci: Fix an error code in probe
usb: dwc3: Fix NULL pointer exception in dwc3_pci_remove()
xhci: Add quirk to workaround the errata seen on Cavium Thunder-X2 Soc
usb: xhci: fix timeout for transition from RExit to U0
usb: xhci: fix uninitialized completion when USB3 port got wrong status
xhci: Add check for invalid byte size error when UAS devices are connected.
xhci: handle port status events for removed USB3 hcd
xhci: Fix leaking USB3 shared_hcd at xhci removal
USB: misc: appledisplay: add 20" Apple Cinema Display
USB: quirks: Add no-lpm quirk for Raydium touchscreens
usb: quirks: Add delay-init quirk for Corsair K70 LUX RGB
USB: Wait for extra delay time after USB_PORT_FEAT_RESET for quirky hub
usb: dwc3: gadget: Properly check last unaligned/zero chain TRB
usb: dwc3: core: Clean up ULPI device
The F81532/534 had a internal configuration space to save & control
IC state with address F81534_CUSTOM_ADDRESS_START (0x2f00). Layout
as following:
+00h: to indicate the section is valid
+01h~04h: UART Mode & port availability
+05h~08h: Output pin control on IC power on
+09h~12h: Output pin control on working <-- New added
Old driver will use +05~08h as default on working, but newer IC will
configed with shutdown mode(7) in 05h~08h and working mode with RS232(1)
in 09h~12h. It'll make mainstream driver not working.
This patch will make mainstream driver compatible older and newer IC.
If using a old IC, the +05h~08h will be 00h~06h, we'll direct apply it.
If using a new IC, the +05h~08h will be 07h or larger, we'll read +09h~12h
to apply newer configuration.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
idVendor 0x0572
idProduct 0x1349
Signed-off-by: Maarten Jacobs <maarten256@outlook.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'cipher' algorithms (single block ciphers) are always synchronous, so
passing CRYPTO_ALG_ASYNC in the mask to crypto_alloc_cipher() has no
effect. Many users therefore already don't pass it, but some still do.
This inconsistency can cause confusion, especially since the way the
'mask' argument works is somewhat counterintuitive.
Thus, just remove the unneeded CRYPTO_ALG_ASYNC flags.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
USB3 roothub might autosuspend before a plugged USB3 device is detected,
causing USB3 device enumeration failure.
USB3 devices don't show up as connected and enabled until USB3 link trainig
completes. On a fast booting platform with a slow USB3 link training the
link might reach the connected enabled state just as the bus is suspending.
If this device is discovered first time by the xhci_bus_suspend() routine
it will be put to U3 suspended state like the other ports which failed to
suspend earlier.
The hub thread will notice the connect change and resume the bus,
moving the port back to U0
This U0 -> U3 -> U0 transition right after being connected seems to be
too much for some devices, causing them to first go to SS.Inactive state,
and finally end up stuck in a polling state with reset asserted
Fix this by failing the bus suspend if a port has a connect change or is
in a polling state in xhci_bus_suspend().
Don't do any port changes until all ports are checked, buffer all port
changes and only write them in the end if suspend can proceed
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will clear the USB_PORT_FEAT_C_CONNECTION bit in case of a hub port reset
only if a device is was attached to the hub port before resetting the hub port.
Using a Lenovo T480s attached to the ultra dock it was not possible to detect
some usb-c devices at the dock usb-c ports because the hub_port_reset code
will clear the USB_PORT_FEAT_C_CONNECTION bit after the actual hub port reset.
Using this device combo the USB_PORT_FEAT_C_CONNECTION bit was set between the
actual hub port reset and the clear of the USB_PORT_FEAT_C_CONNECTION bit.
This ends up with clearing the USB_PORT_FEAT_C_CONNECTION bit after the
new device was attached such that it was not detected.
This patch will not clear the USB_PORT_FEAT_C_CONNECTION bit if there is
currently no device attached to the port before the hub port reset.
This will avoid clearing the connection bit for new attached devices.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
type used on unaligned transfers on dwc3. Also a fix for a NULL pointer
dereference in dwc3_pci_remove(). Note that a recent commit on ffs was
reverted because it causes a regression elsewere.
-----BEGIN PGP SIGNATURE-----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=hWLY
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
For now only 5 small fixes. Most importantly, we have a fix for the TRB
type used on unaligned transfers on dwc3. Also a fix for a NULL pointer
dereference in dwc3_pci_remove(). Note that a recent commit on ffs was
reverted because it causes a regression elsewere.
* tag 'fixes-for-v4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: dwc3: gadget: fix ISOC TRB type on unaligned transfers
Revert "usb: gadget: ffs: Fix BUG when userland exits with submitted AIO transfers"
usb: dwc2: pci: Fix an error code in probe
usb: dwc3: Fix NULL pointer exception in dwc3_pci_remove()
usb: dwc3: gadget: Properly check last unaligned/zero chain TRB
usb: dwc3: core: Clean up ULPI device
When chaining ISOC TRBs together, only the first ISOC TRB should be of
type ISOC_FIRST, all others should be of type ISOC. This patch fixes
that.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We added some error handling to this function but forgot to set the
error code on this path.
Fixes: ecd29dabb2 ("usb: dwc2: pci: Handle error cleanup in probe")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In dwc3_pci_quirks() function, gpiod lookup table is only registered for
baytrail SOC. But in dwc3_pci_remove(), we try to unregistered it
without any checks. This leads to NULL pointer de-reference exception in
gpiod_remove_lookup_table() when unloading the module for non baytrail
SOCs. This patch fixes this issue.
Fixes: 5741022cbd ("usb: dwc3: pci: Add GPIO lookup table on platforms
without ACPI GPIO resources")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/mos7840.c: In function 'mos7840_interrupt_callback':
drivers/usb/serial/mos7840.c:604:14: warning:
variable 'st' set but not used [-Wunused-but-set-variable]
drivers/usb/serial/mos7840.c: In function 'mos7840_write':
drivers/usb/serial/mos7840.c:1303:17: warning:
variable 'data1' set but not used [-Wunused-but-set-variable]
drivers/usb/serial/mos7840.c:1700:11: warning:
variable 'iflag' set but not used [-Wunused-but-set-variable]
They are never used since introduction in commit 3f5429746d ("USB:
Moschip 7840 USB-Serial Driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/quatech2.c: In function 'qt2_process_read_urb':
drivers/usb/serial/quatech2.c:503:27: warning:
variable 'port_priv' set but not used [-Wunused-but-set-variable]
It not used any more after commit 2be818a116 ('Revert "USB: quatech2:
only write to the tty if the port is open."')
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Latest NVIDIA GPU cards have a Cypress CCGx Type-C controller
over I2C interface.
This UCSI I2C driver uses I2C bus driver interface for communicating
with Type-C controller.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Implement workaround for ThunderX2 Errata-129 (documented in
CN99XX Known Issues" available at Cavium support site).
As per ThunderX2errata-129, USB 2 device may come up as USB 1
if a connection to a USB 1 device is followed by another connection to
a USB 2 device, the link will come up as USB 1 for the USB 2 device.
Resolution: Reset the PHY after the USB 1 device is disconnected.
The PHY reset sequence is done using private registers in XHCI register
space. After the PHY is reset we check for the PLL lock status and retry
the operation if it fails. From our tests, retrying 4 times is sufficient.
Add a new quirk flag XHCI_RESET_PLL_ON_DISCONNECT to invoke the workaround
in handle_xhci_port_status().
Cc: stable@vger.kernel.org
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This definition is used by msecs_to_jiffies in milliseconds.
According to the comments, max rexit timeout should be 20ms.
Align with the comments to properly calculate the delay.
Verified on Sunrise Point-LP and Cannon Lake.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek USB3.0 Card Reader [0bda:0328] reports wrong port status on
Cannon lake PCH USB3.1 xHCI [8086:a36d] after resume from S3,
after clear port reset it works fine.
Since this device is registered on USB3 roothub at boot,
when port status reports not superspeed, xhci_get_port_status will call
an uninitialized completion in bus_state[0].
Kernel will hang because of NULL pointer.
Restrict the USB2 resume status check in USB2 roothub to fix hang issue.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Observed "TRB completion code (27)" error which corresponds to Stopped -
Length Invalid error(xhci spec section 4.17.4) while connecting USB to
SATA bridge.
Looks like this case was not considered when the following patch[1] was
committed. Hence adding this new check which can prevent
the invalid byte size error.
[1] ade2e3a xhci: handle transfer events without TRB pointer
Cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <sandeep.singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At xhci removal the USB3 hcd (shared_hcd) is removed before the primary
USB2 hcd. Interrupts for port status changes may still occur for USB3
ports after the shared_hcd is freed, causing NULL pointer dereference.
Check if xhci->shared_hcd is still valid before handing USB3 port events
Cc: <stable@vger.kernel.org>
Reported-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the shared_hcd pointer is valid when calling usb_put_hcd()
The shared_hcd is removed and freed in xhci by first calling
usb_remove_hcd(xhci->shared_hcd), and later
usb_put_hcd(xhci->shared_hcd)
Afer commit fe190ed0d6 ("xhci: Do not halt the host until both HCD have
disconnected their devices.") the shared_hcd was never properly put as
xhci->shared_hcd was set to NULL before usb_put_hcd(xhci->shared_hcd) was
called.
shared_hcd (USB3) is removed before primary hcd (USB2).
While removing the primary hcd we might need to handle xhci interrupts
to cleanly remove last USB2 devices, therefore we need to set
xhci->shared_hcd to NULL before removing the primary hcd to let xhci
interrupt handler know shared_hcd is no longer available.
xhci-plat.c, xhci-histb.c and xhci-mtk first create both their hcd's before
adding them. so to keep the correct reverse removal order use a temporary
shared_hcd variable for them.
For more details see commit 4ac53087d6 ("usb: xhci: plat: Create both
HCDs before adding them")
Fixes: fe190ed0d6 ("xhci: Do not halt the host until both HCD have disconnected their devices.")
Cc: Joel Stanley <joel@jms.id.au>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: <stable@vger.kernel.org>
Reported-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Jack Pham <jackp@codeaurora.org>
Tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add another Apple Cinema Display to the list of supported displays
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Raydium USB touchscreen fails to set config if LPM is enabled:
[ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.030660] usb 1-8: Product: Raydium Touch System
[ 2.030661] usb 1-8: Manufacturer: Raydium Corporation
[ 7.132209] usb 1-8: can't set config #1, error -110
Same behavior can be observed on 2386:3114.
Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[ 206.143691] usb 3-2.4: device descriptor read/64, error -32
[ 206.351671] usb 3-2.4: device descriptor read/64, error -32
Info for this hub:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1a40 ProdID=0101 Rev=01.11
S: Product=USB 2.0 Hub
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.
Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in comment
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_pool_destroy() can handle NULL pointer correctly, so there is
no need to check NULL pointer before calling dma_pool_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the initial connect to a non-pd port, sink would hard reset
twice before deeming that the port partner is non-pd. TCPM sets the
the charge path to false during the hard reset. This causes unnecessary
connects/disconnects of charge path and makes port take longer to
charge from the non-pd ports. Avoid this by not setting the charge path
to false unless the partner has already identified to be pd capable.
When partner is a pd port, set the charge path to false in
SNK_HARD_RESET_SINK_OFF. Set the current limits to default value based
of CC pull up and resume the charge path when port enters
SNK_HARD_RESET_SINK_ON.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
--------
Changes in V3:
Rebase on top of usb-next
Changes in V2:
Based on feedback of jackp@codeaurora.org
- vsafe_5v_hard_reset flag from tcpc_config is removed
- Patch only differentiates between pd port partner and non-pd port
partner
V1 version of the patch is here:
https://lkml.org/lkml/2018/9/14/11
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During HARD_RESET the data link is disconnected.
For self powered device, the spec is advising against doing that.
>From USB_PD_R3_0
7.1.5 Response to Hard Resets
Device operation during and after a Hard Reset is defined as follows:
Self-powered devices Should Not disconnect from USB during a Hard Reset
(see Section 9.1.2).
Bus powered devices will disconnect from USB during a Hard Reset due to the
loss of their power source.
Tackle this by letting TCPM know whether the device is self or bus powered.
This overcomes unnecessary port disconnections from hard reset.
Also, speeds up the enumeration time when connected to Type-A ports.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
---------
Version history:
V3:
Rebase on top of usb-next
V2:
Based on feedback from heikki.krogerus@linux.intel.com
- self_powered added to the struct tcpm_port which is populated from
a. "connector" node of the device tree in tcpm_fw_get_caps()
b. "self_powered" node of the tcpc_config in tcpm_copy_caps
Based on feedbase from linux@roeck-us.net
- Code was refactored
- SRC_HARD_RESET_VBUS_OFF sets the link state to false based
on self_powered flag
V1 located here:
https://lkml.org/lkml/2018/9/13/94
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current check for the last extra TRB for zero and unaligned transfers
does not account for isoc OUT. The last TRB of the Buffer Descriptor for
isoc OUT transfers will be retired with HWO=0. As a result, we won't
return early. The req->remaining will be updated to include the BUFSIZ
count of the extra TRB, and the actual number of transferred bytes
calculation will be wrong.
To fix this, check whether it's a short or zero packet and the last TRB
chain bit to return early.
Fixes: c6267a5163 ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If dwc3_core_init_mode() fails with deferred probe,
next probe fails on sysfs with
sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:11.0/dwc3.0.auto/dwc3.0.auto.ulpi'
To avoid this failure, clean up ULPI device.
Cc: <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull AFS updates from Al Viro:
"AFS series, with some iov_iter bits included"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
missing bits of "iov_iter: Separate type from direction and use accessor functions"
afs: Probe multiple fileservers simultaneously
afs: Fix callback handling
afs: Eliminate the address pointer from the address list cursor
afs: Allow dumping of server cursor on operation failure
afs: Implement YFS support in the fs client
afs: Expand data structure fields to support YFS
afs: Get the target vnode in afs_rmdir() and get a callback on it
afs: Calc callback expiry in op reply delivery
afs: Fix FS.FetchStatus delivery from updating wrong vnode
afs: Implement the YFS cache manager service
afs: Remove callback details from afs_callback_break struct
afs: Commit the status on a new file/dir/symlink
afs: Increase to 64-bit volume ID and 96-bit vnode ID for YFS
afs: Don't invoke the server to read data beyond EOF
afs: Add a couple of tracepoints to log I/O errors
afs: Handle EIO from delivery function
afs: Fix TTL on VL server and address lists
afs: Implement VL server rotation
afs: Improve FS server rotation error handling
...
-----BEGIN PGP SIGNATURE-----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=V4X4
-----END PGP SIGNATURE-----
Merge tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull new experimental media request API from Mauro Carvalho Chehab:
"A new media request API
This API is needed to support device drivers that can dynamically
change their parameters for each new frame. The latest versions of
Google camera and codec HAL depends on such feature.
At this stage, it supports only stateless codecs.
It has been discussed for a long time (at least over the last 3-4
years), and we finally reached to something that seem to work.
This series contain both the API and core changes required to support
it and a new m2m decoder driver (cedrus).
As the current API is still experimental, the only real driver using
it (cedrus) was added at staging[1]. We intend to keep it there for a
while, in order to test the API. Only when we're sure that this API
works for other cases (like encoders), we'll move this driver out of
staging and set the API into a stone.
[1] We added support for the vivid virtual driver (used only for
testing) to it too, as it makes easier to test the API for the ones
that don't have the cedrus hardware"
* tag 'media/v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (53 commits)
media: dt-bindings: Document the Rockchip VPU bindings
media: platform: Add Cedrus VPU decoder driver
media: dt-bindings: media: Document bindings for the Cedrus VPU driver
media: v4l: Add definition for the Sunxi tiled NV12 format
media: v4l: Add definitions for MPEG-2 slice format and metadata
media: videobuf2-core: Rework and rename helper for request buffer count
media: v4l2-ctrls.c: initialize an error return code with zero
media: v4l2-compat-ioctl32.c: add missing documentation for a field
media: media-request: update documentation
media: media-request: EPERM -> EACCES/EBUSY
media: v4l2-ctrls: improve media_request_(un)lock_for_update
media: v4l2-ctrls: use media_request_(un)lock_for_access
media: media-request: add media_request_(un)lock_for_access
media: vb2: set reqbufs/create_bufs capabilities
media: videodev2.h: add new capabilities for buffer types
media: buffer.rst: only set V4L2_BUF_FLAG_REQUEST_FD for QBUF
media: v4l2-ctrls: return -EACCES if request wasn't completed
media: media-request: return -EINVAL for invalid request_fds
media: vivid: add request support
media: vivid: add mc
...
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The alloc_bootmem_pages_nopanic(size) is a shortcut for
__alloc_bootmem_nopanic(size, PAGE_SIZE, BOOTMEM_LOW_LIMIT) which allocates
PAGE_SIZE aligned memory. Since BOOTMEM_LOW_LIMIT is hardwired to 0 there
is no restrictions on where the allocated memory should reside.
The memblock_alloc_nopanic(size, PAGE_SIZE) also allocates PAGE_SIZE
aligned memory without any restrictions and thus can be used as a
replacement for alloc_bootmem_pages_nopanic()
Link: http://lkml.kernel.org/r/1536927045-23536-12-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting added
to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW9LlHw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnvwCffYmMWyMG9zSOw1oSzFPl7TVN1hYAoMyJqzLg
umyLwWxC9ZWWkrpc3iD8
=ux+Y
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB/PHY driver patches for 4.20-rc1
Lots of USB changes in here, primarily in these areas:
- typec updates and new drivers
- new PHY drivers
- dwc2 driver updates and additions (this old core keeps getting
added to new devices.)
- usbtmc major update based on the industry group coming together and
working to add new features and performance to the driver.
- USB gadget additions for new features
- USB gadget configfs updates
- chipidea driver updates
- other USB gadget updates
- USB serial driver updates
- renesas driver updates
- xhci driver updates
- other tiny USB driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (229 commits)
usb: phy: ab8500: silence some uninitialized variable warnings
usb: xhci: tegra: Add genpd support
usb: xhci: tegra: Power-off power-domains on removal
usbip:vudc: BUG kmalloc-2048 (Not tainted): Poison overwritten
usbip: tools: fix atoi() on non-null terminated string
USB: misc: appledisplay: fix backlight update_status return code
phy: phy-pxa-usb: add a new driver
usb: host: add DT bindings for faraday fotg2
usb: host: ohci-at91: fix request of irq for optional gpio
usb/early: remove set but not used variable 'remain_length'
usb: typec: Fix copy/paste on typec_set_vconn_role() kerneldoc
usb: typec: tcpm: Report back negotiated PPS voltage and current
USB: core: remove set but not used variable 'udev'
usb: core: fix memory leak on port_dev_path allocation
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
USB: serial: cypress_m8: remove set but not used variable 'iflag'
...
Pull tty ioctl updates from Al Viro:
"This is the compat_ioctl work related to tty ioctls.
Quite a bit of dead code taken out, all tty-related stuff gone from
fs/compat_ioctl.c. A bunch of compat bugs fixed - some still remain,
but all more or less generic tty-related ioctls should be covered
(remaining issues are in things like driver-private ioctls in a pcmcia
serial card driver not getting properly handled in 32bit processes on
64bit host, etc)"
* 'work.tty-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (53 commits)
kill TIOCSERGSTRUCT
change semantics of ldisc ->compat_ioctl()
kill TIOCSER[SG]WILD
synclink_gt(): fix compat_ioctl()
pty: fix compat ioctls
compat_ioctl - kill keyboard ioctl handling
gigaset: add ->compat_ioctl()
vt_compat_ioctl(): clean up, use compat_ptr() properly
gigaset: don't try to printk userland buffer contents
dgnc: don't bother with (empty) stub for TCXONC
dgnc: leave TIOC[GS]SOFTCAR to ldisc
remove fallback to drivers for TIOCGICOUNT
dgnc: break-related ioctls won't reach ->ioctl()
kill the rest of tty COMPAT_IOCTL() entries
dgnc: TIOCM... won't reach ->ioctl()
isdn_tty: TCSBRK{,P} won't reach ->ioctl()
kill capinc_tty_ioctl()
take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()
synclink: reduce pointless checks in ->ioctl()
complete ->[sg]et_serial() switchover
...
Pull siginfo updates from Eric Biederman:
"I have been slowly sorting out siginfo and this is the culmination of
that work.
The primary result is in several ways the signal infrastructure has
been made less error prone. The code has been updated so that manually
specifying SEND_SIG_FORCED is never necessary. The conversion to the
new siginfo sending functions is now complete, which makes it
difficult to send a signal without filling in the proper siginfo
fields.
At the tail end of the patchset comes the optimization of decreasing
the size of struct siginfo in the kernel from 128 bytes to about 48
bytes on 64bit. The fundamental observation that enables this is by
definition none of the known ways to use struct siginfo uses the extra
bytes.
This comes at the cost of a small user space observable difference.
For the rare case of siginfo being injected into the kernel only what
can be copied into kernel_siginfo is delivered to the destination, the
rest of the bytes are set to 0. For cases where the signal and the
si_code are known this is safe, because we know those bytes are not
used. For cases where the signal and si_code combination is unknown
the bits that won't fit into struct kernel_siginfo are tested to
verify they are zero, and the send fails if they are not.
I made an extensive search through userspace code and I could not find
anything that would break because of the above change. If it turns out
I did break something it will take just the revert of a single change
to restore kernel_siginfo to the same size as userspace siginfo.
Testing did reveal dependencies on preferring the signo passed to
sigqueueinfo over si->signo, so bit the bullet and added the
complexity necessary to handle that case.
Testing also revealed bad things can happen if a negative signal
number is passed into the system calls. Something no sane application
will do but something a malicious program or a fuzzer might do. So I
have fixed the code that performs the bounds checks to ensure negative
signal numbers are handled"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (80 commits)
signal: Guard against negative signal numbers in copy_siginfo_from_user32
signal: Guard against negative signal numbers in copy_siginfo_from_user
signal: In sigqueueinfo prefer sig not si_signo
signal: Use a smaller struct siginfo in the kernel
signal: Distinguish between kernel_siginfo and siginfo
signal: Introduce copy_siginfo_from_user and use it's return value
signal: Remove the need for __ARCH_SI_PREABLE_SIZE and SI_PAD_SIZE
signal: Fail sigqueueinfo if si_signo != sig
signal/sparc: Move EMT_TAGOVF into the generic siginfo.h
signal/unicore32: Use force_sig_fault where appropriate
signal/unicore32: Generate siginfo in ucs32_notify_die
signal/unicore32: Use send_sig_fault where appropriate
signal/arc: Use force_sig_fault where appropriate
signal/arc: Push siginfo generation into unhandled_exception
signal/ia64: Use force_sig_fault where appropriate
signal/ia64: Use the force_sig(SIGSEGV,...) in ia64_rt_sigreturn
signal/ia64: Use the generic force_sigsegv in setup_frame
signal/arm/kvm: Use send_sig_mceerr
signal/arm: Use send_sig_fault where appropriate
signal/arm: Use force_sig_fault where appropriate
...
In the iov_iter struct, separate the iterator type from the iterator
direction and use accessor functions to access them in most places.
Convert a bunch of places to use switch-statements to access them rather
then chains of bitwise-AND statements. This makes it easier to add further
iterator types. Also, this can be more efficient as to implement a switch
of small contiguous integers, the compiler can use ~50% fewer compare
instructions than it has to use bitwise-and instructions.
Further, cease passing the iterator type into the iterator setup function.
The iterator function can set that itself. Only the direction is required.
Signed-off-by: David Howells <dhowells@redhat.com>
Smatch complains that "reg" can be uninitialized if the
abx500_get_register_interruptible() call fails. It's an interruptable
function, so we should check if the user presses CTRL-C.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic power-domain framework has been updated to allow devices
that require more than one power-domain to create a new device for
each power-domain required and then link these new power-domain
devices to the consumer device.
Update the Tegra xHCI driver to use the new APIs provided by the
generic power-domain framework so we can use the generic power-domain
framework for managing the xHCI controllers power-domains. Please
note that to maintain backward compatibility with older device-tree
blobs these new generic power-domain APIs are only used if the
'power-domains' property is present and otherwise we fall back to
using the legacy Tegra APIs for managing the power-domains.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the XUSB power domains used by the Tegra xHCI controller are
never powered off on the removal of the driver, however, they will be
powered off on probe failure. Update the removal code to be consistent
with the probe failure path to power off the XUSB power domains.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rmmod path, usbip_vudc does platform_device_put() twice once from
platform_device_unregister() and then from put_vudc_device().
The second put results in:
BUG kmalloc-2048 (Not tainted): Poison overwritten error or
BUG: KASAN: use-after-free in kobject_put+0x1e/0x230 if KASAN is
enabled.
[ 169.042156] calling init+0x0/0x1000 [usbip_vudc] @ 1697
[ 169.042396] =============================================================================
[ 169.043678] probe of usbip-vudc.0 returned 1 after 350 usecs
[ 169.044508] BUG kmalloc-2048 (Not tainted): Poison overwritten
[ 169.044509] -----------------------------------------------------------------------------
...
[ 169.057849] INFO: Freed in device_release+0x2b/0x80 age=4223 cpu=3 pid=1693
[ 169.057852] kobject_put+0x86/0x1b0
[ 169.057853] 0xffffffffc0c30a96
[ 169.057855] __x64_sys_delete_module+0x157/0x240
Fix it to call platform_device_del() instead and let put_vudc_device() do
the platform_device_put().
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon success the update_status handler returns a positive number
corresponding to the number of bytes transferred by usb_control_msg.
However the return code of the update_status handler should indicate if
an error occurred(negative) or how many bytes of the user's input to sysfs
that was consumed. Return code zero indicates all bytes were consumed.
The bug can for example result in the update_status handler being called
twice, the second time with only the "unconsumed" part of the user's input
to sysfs. Effectively setting an incorrect brightness.
Change the update_status handler to return zero for all successful
transactions and forward usb_control_msg's error code upon failure.
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.20-rc1, including:
- support for CBUS GPIO on FTDI devices (FTX and FT232R)
- fix of a long-standing transfer-length bug
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=V6Jo
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.20-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.20-rc1
Here are the USB-serial updates for 4.20-rc1, including:
- support for CBUS GPIO on FTDI devices (FTX and FT232R)
- fix of a long-standing transfer-length bug
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.20-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cypress_m8: remove set but not used variable 'iflag'
USB: serial: cypress_m8: fix interrupt-out transfer length
USB: serial: ftdi_sio: add support for FT232R CBUS gpios
USB: serial: ftdi_sio: fix gpio name collisions
USB: serial: ftdi_sio: implement GPIO support for FT-X devices
USB: serial: cypress_m8: fix spelling mistake "retreiving" -> "retrieving"
num can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/gadget/function/f_mass_storage.c:3177 fsg_lun_make() warn:
potential spectre issue 'fsg_opts->common->luns' [r] (local cap)
Fix this by sanitizing num before using it to index
fsg_opts->common->luns
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Felipe Balbi <felipe.balbi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7a68d9fb85 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs. However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer. (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)
This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes: 7a68d9fb85 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
atmel,oc-gpio is optional. Request its irq only when atmel,oc is set
in device tree.
devm_gpiod_get_index_optional returns NULL if -ENOENT. Check its
return value for NULL before error, because it is more probable that
atmel,oc is not set.
This fixes the following errors on boards where atmel,oc is not set in
device tree:
[ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[ 0.960000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
[ 0.970000] at91_ohci 500000.ohci: failed to request gpio "overcurrent" IRQ
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... and fix the return value - on success it used to have ioctl(2)
fill the user-supplied struct serial_struct and return -ENOTTY.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
add such methods for usb_serial_driver, provide tty_operations
->[sg]et_serial() calling those. For now the lack of methods
in driver means ENOIOCTLCMD from usb-serial ->[sg]et_serial(),
making tty_ioctl() fall back to calling ->ioctl(). Once all
drivers are converted, we'll be returning -ENOTTY instead,
completing the switchover.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Intel Apollo Lake has the same internal USB role mux as
Intel Cherry Trail.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing pm_runtime_disable() to remove(), in order to avoid
an Unbalanced pm_runtime_enable when the module is removed and
re-probed.
Error log:
root@intel-corei7-64:~# modprobe -r intel_xhci_usb_role_switch
root@intel-corei7-64:~# modprobe intel_xhci_usb_role_switch
intel_xhci_usb_sw intel_xhci_usb_sw: Unbalanced pm_runtime_enable!
Fixes: cb29684686 (usb: roles: intel_xhci: Enable runtime PM)
Cc: <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb standard ("Universal Serial Bus Class Definitions for Communication
Devices") distiguishes between "consistent signals" (DSR, DCD), and
"irregular signals" (break, ring, parity error, framing error, overrun).
The bits of "irregular signals" are set, if this error/event occurred on
the device side and are immeadeatly unset, if the serial state notification
was sent.
Like other drivers of real serial ports do, just the occurence of those
events should be counted in serial_icounter_struct (but no 1->0
transitions).
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resetting the write index of the notification buffer on urb unlink (e.g.
closing a cdc-acm device from userspace) may lead to wrong interpretation
of further received notifications, in case the index is not 0 when urb
unlink happens (i.e. when parts of a notification already have been
transferred). On the device side there is no "reset" of the notification
transimission and thus we would get out of sync with the device.
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device splits up a control message and a reset() happens
between the parts, the message is lost and already recieved parts
must be dropped.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 1aba579f3c ("cdc-acm: handle read pipe errors")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vhci_hub_control() accesses port_status array with out of bounds port
value. Fix it to reference port_status[] only with a valid rhport value
when invalid_rhport flag is true.
The invalid_rhport flag is set early on after detecting in port value
is within the bounds or not.
The following is used reproduce the problem and verify the fix:
C reproducer: https://syzkaller.appspot.com/x/repro.c?x=14ed8ab6400000
Reported-by: syzbot+bccc1fe10b70fadc78d0@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/early/xhci-dbc.c: In function 'xdbc_handle_tx_event':
drivers/usb/early/xhci-dbc.c:720:9: warning:
variable 'remain_length' set but not used [-Wunused-but-set-variable]
It never be used since introduction in
commit aeb9dd1de9 ("usb/early: Add driver for xhci debug capability")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This must have been copy pasted from the function above. Fix it.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when requesting a specific voltage or current through
the psy interface, for PPS, when reading back from that interface
the values will always be the same as previously given, if the
request was successful. However PPS only allows for 20mV voltage
steps and 50mA current steps, and the psy class expects microvolt
and micro amp requests, so inbetween values can be provided through
this interface. Really when reading back the true values negotiated
should be given, and not the ones originally asked for.
To report the actual values negotiated with the Source, the values
stored are now rounded down to the relevant step units prior to
building the PPS request, so that those values are later correctly
reported through the psy interface. In addition this improves the
adjustments made to meet the operating power requirements of the
platform, which previously could have been slightly out due to not
using valid PPS units of voltage and current.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/core/driver.c: In function 'usb_driver_claim_interface':
drivers/usb/core/driver.c:513:21: warning:
variable 'udev' set but not used [-Wunused-but-set-variable]
Since commit c183813fce ("USB: remove LPM management from
usb_driver_claim_interface()"), 'udev' is not used.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the allocation of port_dev_path from the call to
kobject_get_path is not being kfree'd, causing a memory leak. Fix
this by kfree'ing this at the end of the function. Add an extra
error exit path to fix one of the early leaks when envp[0] fails
to be allocated.
Detected by CoverityScan, CID#1473771 ("Resource Leak")
Fixes: 201af55da8 ("usb: core: added uevent for over-current")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- improve overcorrent handling for imx
- some small code restructure (no function affect)
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJburdqExxwZXRlci5jaGVuQG54cC5jb20ACgkQSFkpgVDWcbsr
ogf8C3QeuruN4+awCx4VQ7QPOhy0ewdr0OL3DCt1wjZkhvKilXcLHtKimbm7QQ7F
9tHFpxya63MwZvnqjEGR/EgJpTPGVTx1KSBcBoEQn5qP+iYA/xVSYGpeLEHGZtQE
FtsJGXg/dT1uzho43CibCksqiyHpScNAdUn9wl6go/LJKycVQ3nu+6R+kXbc+0ca
gzPXUsApG4KTEJ8SH5eGZnx2uqZzhJnuYXDRr/8mw6S1GyM6wlobVHvSyhpj1uGy
OsXluLgfu/+o+HYKwmKpqg2gZonk+1r2rE0qSmoAI7rYmX3irBC6VvASYqrok5jj
lKQ/a/M8IeIsXo1a/Xv62SKU3w==
=loIF
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-testing
Peter writes:
- Add pinctrl support for dual-role switch at chipidea-core
- improve overcorrent handling for imx
- some small code restructure (no function affect)
* tag 'usb-ci-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: Fix otg event handler
usb: chipidea: Prevent unbalanced IRQ disable
doc: usb: ci-hdrc-usb2: Add pinctrl properties definition
usb: chipidea: Add dynamic pinctrl selection
usb: chipidea: imx: make MODULE_LICENCE and SPDX-identifier match
usb: chipidea: imx: enable OTG overcurrent in case USB subsystem is already started
usb: chipidea: imx: do not use preprocessor conditionals for PM
With 63 non-merge commits, this is not a large merge window for USB
peripheral. The largest changes go to the UVC gadget driver which a
few folks have been improving.
Apart from UVC changes, we have a few more devices being added to
Renesas USB3 and DWC3 controller drivers and a couple minor bug fixes
on other drivers.
-----BEGIN PGP SIGNATURE-----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=XZcP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB for v4.20
With 63 non-merge commits, this is not a large merge window for USB
peripheral. The largest changes go to the UVC gadget driver which a
few folks have been improving.
Apart from UVC changes, we have a few more devices being added to
Renesas USB3 and DWC3 controller drivers and a couple minor bug fixes
on other drivers.
* tag 'usb-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (63 commits)
USB: net2280: Remove ->disconnect() callback from net2280_pullup()
usb: dwc2: disable power_down on rockchip devices
usb: gadget: udc: renesas_usb3: add support for r8a77990
dt-bindings: usb: renesas_usb3: add bindings for r8a77990
usb: gadget: udc: renesas_usb3: Add r8a774a1 support
usb: gadget: udc: renesas_usb3: Fix b-device mode for "workaround"
usb: dwc2: gadget: Add handler for WkupAlert interrupt
usb: dwc2: gadget: enable WKUP_ALERT interrupt
usb: dwc2: gadget: Program GREFCLK register
usb: dwc2: gadget: Add parameters for GREFCLK register
usb: dwc2: Add definitions for new registers
usb: dwc2: Update target (u)frame calculation
usb: dwc2: Add dwc2_gadget_dec_frame_num_by_one() function
usb: dwc2: Add core parameter for service interval support
usb: dwc2: Update registers definitions to support service interval
usb: renesas_usbhs: add support for R-Car E3
dt-bindings: usb: renesas_usbhs: add bindings for r8a77990
usb: renesas_usbhs: rcar3: Use OTG mode for R-Car D3
Revert "usb: renesas_usbhs: set the mode by using extcon state for non-otg channel"
usb: gadget: f_uac2: disable IN/OUT ep if unused
...
The net2280 UDC driver invokes the gadget driver's ->disconnect()
callback routine when the net2280_pullup() routine turns off the D+
pullup. This is now unnecessary, because the gadget core performs the
callback on our behalf. This patch removes the unneeded callback.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The bug would let the usb controller enter partial power down,
which was formally known as hibernate, upon boot if nothing was plugged
in to the port. Partial power down couldn't be exited properly, so any
usb devices plugged in after boot would not be usable.
Before the name change, params.hibernation was false by default, so
_dwc2_hcd_suspend() would skip entering hibernation. With the
rename, _dwc2_hcd_suspend() was changed to use params.power_down
to decide whether or not to enter partial power down.
Since params.power_down is non-zero by default, it needs to be set
to 0 for rockchip devices to restore functionality.
This bug was reported in the linux-usb thread:
REGRESSION: usb: dwc2: USB device not seen after boot
The commit that caused this regression is:
6d23ee9caa
Signed-off-by: SolidHal <hal@halemmerich.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since r8a77990 (R-Car E3) doesn't have VBUS detect pin and
number of ramif is 4, this patch adds a new renesas_usb3_priv
variable for the SoC.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/serial/cypress_m8.c: In function 'cypress_set_termios':
drivers/usb/serial/cypress_m8.c:866:18: warning:
variable 'iflag' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix interrupt-out transfer length which was being set to the
transfer-buffer length rather than the size of the outgoing packet.
Note that no slab data was leaked as the whole transfer buffer is always
cleared before each transfer.
Fixes: 9aa8dae7b1 ("cypress_m8: use usb_fill_int_urb where appropriate")
Signed-off-by: Johan Hovold <johan@kernel.org>
Enable support for cbus gpios on FT232R. The cbus configuration is
stored in one word in the EEPROM at offset 0x0a (byte-offset 0x14) with
the mux config for CBUS0, CBUS1, CBUS2 and CBUS3 in bits 0..3, 4..7,
8..11 and 12..15, respectively.
Tested using FT232RL by configuring one cbus pin at a time.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the gpio line names, which cause gpiolib to complain loudly
whenever a second ftdi gpiochip is registered:
gpio gpiochip5: Detected name collision for GPIO name 'CBUS0'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS1'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS2'
gpio gpiochip5: Detected name collision for GPIO name 'CBUS3'
and also prevents the legacy sysfs interface from being used (as the
line names are used as device names whenever they are set):
sysfs: cannot create duplicate filename '/class/gpio/CBUS0'
Until non-unique names are supported by gpiolib (without warnings and
stack dumps), let's leave the gpio lines unnamed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Linus recently observed that if we did not worry about the padding
member in struct siginfo it is only about 48 bytes, and 48 bytes is
much nicer than 128 bytes for allocating on the stack and copying
around in the kernel.
The obvious thing of only adding the padding when userspace is
including siginfo.h won't work as there are sigframe definitions in
the kernel that embed struct siginfo.
So split siginfo in two; kernel_siginfo and siginfo. Keeping the
traditional name for the userspace definition. While the version that
is used internally to the kernel and ultimately will not be padded to
128 bytes is called kernel_siginfo.
The definition of struct kernel_siginfo I have put in include/signal_types.h
A set of buildtime checks has been added to verify the two structures have
the same field offsets.
To make it easy to verify the change kernel_siginfo retains the same
size as siginfo. The reduction in size comes in a following change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Trivial fix to spelling mistakes in debug warning messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/typec/tcpm/tcpm.c: In function 'tcpm_pd_select_pps_apdo':
drivers/usb/typec/tcpm/tcpm.c:2212:39: warning:
variable 'snk_ma' set but not used [-Wunused-but-set-variable]
drivers/usb/typec/tcpm/tcpm.c: In function 'tcpm_pd_build_pps_request':
drivers/usb/typec/tcpm/tcpm.c:2405:37: warning:
variable 'min_mv' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform firmware "location" data is used to find port peer
relationships. But firmware is an unreliable source, and there are
real world examples of errors leading to missing or wrong peer
relationships. Debugging this is currently hard.
Exporting the location attribute makes it easier to spot mismatches
between the firmware data and the real world.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new scheme is required just to support legacy low and full-speed
devices. For high speed devices, it will slower the enumeration speed.
So in this patch we try the "old" enumeration scheme first for high speed
devices, and this is what Windows does since Windows 8.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current code mistakenly checks against max current to determine
order but this should be max voltage. This commit fixes the issue
so order is correctly determined, thus avoiding failure based on
a higher voltage PPS APDO having a lower maximum current output,
which is actually valid.
Fixes: 2eadc33f40 ("typec: tcpm: Add core support for sink side PPS")
Cc: <stable@vger.kernel.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the "workaround_for_vbus" is true, the driver will not call
usb_disconnect(). So, since the controller keeps some registers'
value, the driver doesn't re-enumarate suitable speed after
the b-device mode is disabled. To fix the issue, this patch
adds usb_disconnect() calling in renesas_usb3_b_device_write()
if workaround_for_vbus is true.
Fixes: 43ba968b00 ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added interrupt handler for WkupAlert interrupt.
This interrupt should initiate Remote Wake up.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
WKUP_ALERT interrupt should be unmask when lpm mode is enabled.
This interrupt is asserted when the device is in L1 for the duration
mentioned in GREFCLK.SOF_CNN_WKUP_ALERT. This is used to alert SW to
initiate Remote wake up so that the device resumes in time in order not
to lose sync with the host frame number.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added dwc2_gadget_program_ref_clk function to program GREFCLK
register in device mode.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added ref_clk_per and sof_cnt_wkup_alert parameters in
dwc2_core_params struct and set default values.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
New registers were added to dwc otg core.
GREFCLK - This register used to control ref_clk parameters.
GINTSTS2 - New WKUP_ALERT interrupt was added.
GINTMSK2 - Mask register for GINTSTS2.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In service interval based scheduling target (u)frame must be
set as a last frame in this the service interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added dwc2_gadget_dec_frame_num_by_one() function in gadget.c.
This function will be used to calculate descriptor frame number field
value. For service interval mode frame number in descriptor should point
to last (u)frame in the interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added core parameter for service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_SERVICE_INTERVAL_SUPPORTED and
DCTL_SERVICE_INTERVAL_SUPPORTED bits definitions to support
service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for R-Car E3. This SoC needs to release
the PLL reset by the UGCTRL register like R-Car D3. So, this patch
adds a usbhs_of_match entry for this SoC with
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since R-Car D3 can use OTG mode, this patch changes the UGCTRL2
value to UGCTRL2_USB0SEL_OTG and UGCTRL2_VBUSSEL like other R-Car
Gen3 SoCs.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit cd14247d5c.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Via p_chmask/c_chmask the user can define whether uac2 shall support
playback and/or capture. This has only effect on the created ALSA device,
but not on the USB descriptor. This patch adds playback/capture descriptors
dependent on that parameter.
Signed-off-by: Andreas Pape <apape@de.adit-jv.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget documentation doesn't state clearly whether a gadget
driver's ->disconnect() callback should be invoked when the D+ pullup
is turned off. Some UDC drivers do this and some don't. This patch
settles the issue by making the core function usb_gadget_disconnect()
issue the callback, so that UDC drivers don't need to worry about it.
A description of the new behavior is added to the function's
kerneldoc. Also, the patch removes a few superseded callbacks from
other core routines.
Future patches will remove the ->disconnect() calls from the UDC
drivers that make them, as they are now unnecessary. Until all those
patches are merged gadget drivers may receive extra ->disconnect()
callbacks, but this should be harmless.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'optimizations' was misspelled as 'optmizations'. Fixed it. It is a
coding style change which should have no impact on runtime execution of code.
Signed-off-by: Faisal Mehmood <f.m3hm00d@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The name is always non-NULL and then is not used anywhere in this function,
so remove it.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-usb@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The original implementation from commit b504882da5
("USB: add Freescale high-speed USB SOC device controller driver")
returned NULL on failure and an allocated + initialized struct fsl_udc on
success. The current code introduced in commit 4365831dad
("USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register") only
provides partial initialization as well as returning 0 on success and -1
on failures. The function documentation is updated accordingly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 4365831dad ("USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The allocation with fsl_alloc_request() and kmalloc() were unchecked
fixed this up with a NULL check and appropriate cleanup.
Additionally udc->ep_qh_size was reset to 0 on failure of allocation.
Similar udc->phy_mode is initially 0 (as udc_controller was
allocated with kzalloc in fsl_udc_probe()) so reset it to 0 as well
so that this function is side-effect free on failure. Not clear if
this is necessary or sensible as fsl_udc_release() probably can not
be called if fsl_udc_probe() failed - but it should not hurt.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: b504882da5 ("USB: add Freescale high-speed USB SOC device controller driver")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The vbus rise & fall interrupts are used to enable and disable
U3 function of device automatically, this cause some issues when
class driver is initialized as deactivated, and will skip over
software-controlled connect by pullup(), but UDC wants to keep
disconnect until usb_gadget_activate() is called which calls
pullup() if needed. So we disable vbus rise & fall interrupts
and just use pullup() to enable & disable U3 function, and reset
mtu3 state when disconnect instead when vbus fall.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
R-Car Gen3 needs to enable clocks of both host and peripheral.
Since [eo]hci-platform disables the reset(s) when the drivers are
removed, renesas_usbhs driver doesn't work correctly. To fix this
issue, this patch adds multiple clocks management on this
renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
R-Car Gen3 needs to deassert resets of both host and peripheral.
Since [eo]hci-platform is possible to assert the reset(s) when
the probing failed, renesas_usbhs driver doesn't work correctly
regardless of finished probing. To fix this issue, this patch adds
reset_control on this renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using external vbus supply regulator, it should be enabled
synchronously with PWR bit in HPRT register. This also fixes
unbalanced use of this optional regulator (This can be reproduced
easily when unbinding the driver).
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_vbus_supply_exit() may call regulator_disable(). It shouldn't be
called with interrupts disabled as it might sleep.
This is seen with DEBUG_ATOMIC_SLEEP=y.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a race with root hub resume, when using external vbus supply.
Root hub gets resumed, but runtime pm autosuspend runs as external vbus
supply isn't enabled. So, host never exit from power down properly.
Initialize vbus external supply before, rater that after hub resume.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Like the omap back-end, we get a link error with CONFIG_EXTCON=m
when building the qcom back-end into the kernel:
drivers/usb/dwc3/dwc3-qcom.o: In function `dwc3_qcom_probe':
dwc3-qcom.c:(.text+0x13dc): undefined reference to `extcon_get_edev_by_phandle'
dwc3-qcom.c:(.text+0x1b18): undefined reference to `devm_extcon_register_notifier'
dwc3-qcom.c:(.text+0x1b9c): undefined reference to `extcon_get_state'
Do the same thing as OMAP and add an explicit dependency on
EXTCON.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The at91sam9rl PMC is not quite the same as the at91sam9g45 one and now has
its own compatible string. Add support for that.
Fixes: 217bace8e548 ("ARM: dts: fix PMC compatible")
Acked-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver may sleep in an interrupt handler.
The function call path (from bottom to top) in Linux-4.17 is:
[FUNC] fotg210_ep_queue(GFP_KERNEL)
drivers/usb/gadget/udc/fotg210-udc.c, 744:
fotg210_ep_queue in fotg210_get_status
drivers/usb/gadget/udc/fotg210-udc.c, 768:
fotg210_get_status in fotg210_setup_packet
drivers/usb/gadget/udc/fotg210-udc.c, 949:
fotg210_setup_packet in fotg210_irq (interrupt handler)
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
If possible, spin_unlock() and spin_lock() around fotg210_ep_queue()
can be also removed.
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling all EP's allow to reset EP's to initial state.
On disconnect disable all EP's instead of just killing
all requests. Because of some platform didn't catch
disconnect event, same stuff added to
dwc2_hsotg_core_init_disconnected() function when USB
reset detected on the bus.
Changed from version 1:
Changed lock acquire flow in dwc2_hsotg_ep_disable()
function.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 variant found in Exynos5433 SoCs requires keeping all DRD30/UHOST30
clocks enabled all the time the driver does any access to DWC3 registers,
otherwise external abort happens. So far DWC3 hardware module worked with
samsung,exynos5250-dwusb3 compatible only by luck when built into kernel:
all DRD30 clocks were left enabled by bootloader and later kept enabled
by the DRD PHY driver. However, if one tried to use Exnos DWC3 driver as
a module or performed system suspend/resume cycle, external abort
happened. This patch finally fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add per-variant list of clocks and manage them all together in
the single array. This is a preparation for adding new variants
of Exynos SoCs. No functional changes for existing Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All supported Exynos variants provide respective generic PHY framework
based drivers for controlling USB PHYs, so there is no point
creating fake USB PHYs based on platform devices. While removing useless
code, remove calls to runtime PM, which have no effect.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistake in dev_dbg message
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/usb/gadget/udc/mv_udc_core.c:188:33: warning: equality
comparison with extraneous parentheses [-Wparentheses-equality]
while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~
drivers/usb/gadget/udc/mv_udc_core.c:188:33: note: remove extraneous
parentheses around the comparison to silence this warning
while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
~ ^ ~
drivers/usb/gadget/udc/mv_udc_core.c:188:33: note: use '=' to turn this
equality comparison into an assignment
while ((curr_dqh->curr_dtd_ptr == curr_dtd->td_dma)) {
^~
=
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/120
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch removes a set but unused variable in hcd.c.
Fixes gcc warning:
variable ‘data_fifo’ set but not used [-Wunused-but-set-variable]
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Joshua Abraham <j.abraham1776@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit 8ada211d03.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
In other words, like other R-Car Gen3 SoCs, R-Car D3 can change the mode
by using the phy-rcar-gen3-usb2 driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistakes in debug warning messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Give USB3 devices a better chance to enumerate at USB3 speeds if
they are connected to a suspended host.
Porting from "671ffdff5b13 xhci: resume USB 3 roothub first"
Cc: <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The workaround for missing CAS bit is also needed for xHC on Intel
sunrisepoint PCH. For more details see:
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ACM TTY port is disconnected, the URBs it uses must be killed, and
then the buffers must be freed. Unfortunately a previous refactor removed
the code freeing the buffers because it looked extremely similar to the
code killing the URBs.
As a result, there were many new leaks for each plug/unplug cycle of a
CDC-ACM device, that were detected by kmemleak.
Restore the missing code, and the memory leak is removed.
Fixes: ba8c931ded ("cdc-acm: refactor killing urbs")
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some device-id patches for 4.19-rc7.
Some Quectel modems have a vendor command which can be used to disable
certain interfaces in their configurations, but unlike some other modems
this also causes the interface numbers to change. These patches allow us
to support all such interface permutations at least for the Quectel
EP06.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=82HD
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.19-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.19-rc7
Here are some device-id patches for 4.19-rc7.
Some Quectel modems have a vendor command which can be used to disable
certain interfaces in their configurations, but unlike some other modems
this also causes the interface numbers to change. These patches allow us
to support all such interface permutations at least for the Quectel
EP06.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.19-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: simple: add Motorola Tetra MTP6550 id
USB: serial: option: add two-endpoints device-id flag
USB: serial: option: improve Quectel EP06 detection
Fix uninitialized symbol 'actual' in function
usbtmc_ioctl_abort_bulk_in_tag().
When symbol 'actual' is not initialized and usb_bulk_msg() fails,
the subsequent kernel debug message shows invalid data.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Fixes: cbe743f133 ("usb: usbtmc: Fix ioctl USBTMC_IOCTL_ABORT_BULK_IN")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix uninitialized symbol 'actual' in function usbtmc_ioctl_clear.
When symbol 'actual' is not initialized and usb_bulk_msg() fails,
the subsequent kernel debug message shows a random value.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Fixes: dfee02ac4b ("usb: usbtmc: Fix ioctl USBTMC_IOCTL_CLEAR")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix uninitialized symbol 'actual' in function usbtmc_read.
When symbol 'actual' is not initialized and usb_bulk_msg() fails,
the subsequent kernel debug message shows a random value.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Fixes: d7604ff0dc ("usb: usbtmc: Optimize usbtmc_read")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel memory is allocated twice in new function
usbtmc_ioctl_request and creates a memory leak.
This fix removes the superfluous kmalloc().
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Fixes: 658f24f452 ("usb: usbtmc: Add ioctl for generic requests on control")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for R-Car E3. This SoC needs to release
the PLL reset by the UGCTRL register like R-Car D3. So, this patch
adds a usbhs_of_match entry for this SoC with
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since R-Car D3 can use OTG mode, this patch changes the UGCTRL2
value to UGCTRL2_USB0SEL_OTG and UGCTRL2_VBUSSEL like other R-Car
Gen3 SoCs.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cd14247d5c.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8ada211d03.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
In other words, like other R-Car Gen3 SoCs, R-Car D3 can change the mode
by using the phy-rcar-gen3-usb2 driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 1cbd53c8cd ("usb: core: introduce per-port over-current
counters") usb ports expose a sysfs value 'over_current_count'
to user space. This value on its own is not very useful as it requires
manual polling.
As a solution, fire a udev event from the usb hub device that specifies
the values 'OVER_CURRENT_PORT' and 'OVER_CURRENT_COUNT' that indicate
the path of the usb port where the over-current event occurred and the
value of 'over_current_count' in sysfs. Additionally, call
sysfs_notify() so the sysfs value supports poll().
Signed-off-by: Jon Flatley <jflat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the controller is configured for a fixed power role (Source
only or Sink only), attach does not proceed within the TCPM state
machine as there is no CC event generated by this driver to update
the CC line status.
To rectify this, when CC is configured as Source or Sink we now
make use of the hardware's automatic fixed Source or Sink
toggling mechanism, which detects attaches in the same way as for
DRP toggling. In this way the result of toggling is handled in the
same way by the 'fusb302_handle_togdone()' function, and CC events
are generated as expected for TCPM allowing a contract to be
established.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a typo in the enum name of the 'OFF' state for toggling
(TOGGLINE instead of TOGGLING). This commit resolves that trivial
spelling inconsistency.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When USB bus host controller root hub resumes from autosuspend,
it immediately tries to enter auto-suspend, but there can be a
scenario when root hub is resuming its usb2 ports, in that particular
case USB host controller auto suspend fails since it is busy
to resuming its usb2 ports.
This makes multiple failed cycles of auto-suspend until all usb2
ports of host controller root hub do not resume.
This patch uses USB core framework usb_hcd_start_port_resume,
usb_hcd_end_port_resume API's in order to autoresume/autosuspend
root hub properly.
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XUSB firmware header is in little endian byte order, so make the
fields __le32 and __le16 instead of u32 and u16 to avoid warnings from
sparse when the fields are used with the endian-aware __le32_to_cpu()
and __le16_to_cpu() accessors, respectively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci controller on Alpine and Titan Ridge keeps the whole thunderbolt
awake if the host controller is not allowed tp sleep.
This is the case even if no USB devices are connected to the host.
Because of this bigger impact, allow runtime pm as default for these xhci
controllers in the driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use soft retry to recover from a USB Transaction Errors that are caused by
temporary error conditions. The USB device is not aware that the xHC
has halted the endpoint, and will be waiting for another retry
A Soft Retry perform additional retries and recover from an error which has
caused the xHC to halt an endpoint.
Soft retry has some limitations:
Soft Retry attempts shall not be performed on Isoch endpoints
Soft Retry attempts shall not be performed if the device is behind a TT in
a HS Hub
Software shall limit the number of unsuccessful Soft Retry attempts to
prevent an infinite loop.
For more details on Soft retry see xhci specs 4.6.8.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TPL support is used to identify targeted devices during
EH2.0 and EH3.0 certification test, the user can add "tpl-support"
at dts to enable this feature.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supports SSP scheduling only for SSP device directly connected
to root hub but not through external USB3 gen2 hub which need
use a new scheduling way.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mainly improve SuperSpeed ISOC bandwidth in last microframe,
and LowSpeed/FullSpeed IN INT/ISOC bandwidth in split and
idle microframes by introduing a bandwidth budget table;
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the interval equal zero, needn't round up to power of two
for the number of packets in each ESIT, so fix it.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of maximum ESIT payload of endpoint context to calculate
the number of packets to send in each ESIT
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's dangerous to use empty code define.
Furthermore it lead to the following warning:
"suggest braces around empty body in an « else » statement"
So let's replace emptyness by "do {} while(0)"
Furthermore, as suggested by Joe Perches, rename the macro to INCR.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the quest to remove all stack VLA usage from the kernel[1], this
replaces struct crypto_skcipher and SKCIPHER_REQUEST_ON_STACK() usage
with struct crypto_sync_skcipher and SYNC_SKCIPHER_REQUEST_ON_STACK(),
which uses a fixed stack size.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch allows using the CBUS pins of FT-X devices as GPIO in CBUS
bitbanging mode. There is no conflict between the GPIO and VCP
functionality in this mode. Tested on FT230X and FT231X.
As there is no way to request the current CBUS register configuration
from the device, all CBUS pins are set to a known state when the first
GPIO is requested. This allows using libftdi to set the GPIO pins
before loading this module for UART functionality, a behavior that
existing applications might be relying upon (though no specific case
is known to the authors of this patch).
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: minor style changes ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The driver uses the %d format to print unsigned int values. The correct
format is %u. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Several macros used to define attributes and their access functions take
multiple arguments to specify endianness and string conversion
functions, based on the size of the attribute. This can be simplified by
passing the number of bits explicitly, and constructing the name of the
functions internally.
The UVCG_OPTS_ATTR macro can be simplified further as all fields it
deals with are unsigned int.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
USB descriptors are stored in little endian, requiring the use of
conversion macros. Those macros are incorrectly used for values stored
in native endian structures within the driver. Operation on big endian
platforms is thus broken. Fix it by removing the conversion macros where
they're not needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
The function is never called, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Adding device context to the kernel log messages make them more useful.
Add new uvcg_* macros based on dev_*() that print both the gadget device
name and the function name.
While at it, remove a commented out printk statement and an unused
printk-based macro.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
When USB requests for video data fail to be submitted, the driver
signals a problem to the host by halting the video streaming endpoint.
This is only valid in bulk mode, as isochronous transfers have no
handshake phase and can't thus report a stall. The usb_ep_set_halt()
call returns an error when using isochronous endpoints, which we happily
ignore, but some UDCs complain in the kernel log. Fix this by only
trying to halt the endpoint in bulk mode.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
USB requests for video data are queued from two different locations in
the driver, with the same code block occurring twice. Factor it out to a
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
There is an issue where the host is unable to tell the gadget what frame
rate it wants if the dwFrameIntervals in the interface descriptors are
not in ascending order. This means that when instantiating a uvc gadget
via configfs the user must make sure the dwFrameIntervals are in
ascending order.
Instead of silently failing the breaking of this rule, we sort the
dwFrameIntervals upon writing to configfs.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
While checks are in place to avoid attributes and children of a format
being manipulated after the format is linked into the streaming header,
the linked flag was never actually set, invalidating the protections.
Update the flag as appropriate in the header link calls.
Signed-off-by: Joel Pepper <joel.pepper@rwth-aachen.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
- Add bFrameIndex as a UVCG_FRAME_ATTR_RO for each frame size.
- Automatically assign ascending bFrameIndex to each frame in a format.
Before all "bFrameindex" attributes were set to "1" with no way to
configure the gadget otherwise. This resulted in the host always
negotiating for bFrameIndex 1 (i.e. the first frame size of the gadget).
After the negotiation the host driver will set the user or application
selected frame size, while the gadget is actually set to the first frame
size.
Now, when the containing format is linked into the streaming header,
iterate over all child frame descriptors and assign ascending indices.
The automatically assigned indices can be read from the new read only
bFrameIndex configfs attribute in each frame descriptor item.
Signed-off-by: Joel Pepper <joel.pepper@rwth-aachen.de>
[Simplified documentation, renamed function, blank space update]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
The UVC format description are numbered using the descriptor's
bFormatIndex field. The index is used in UVC requests, and is thus
needed to handle requests in userspace. Make it dynamically discoverable
by exposing it in a bFormatIndex configfs attribute of the uncompressed
and mjpeg format config items.
The bFormatIndex value exposed through the attribute is stored in the
config item private data. However, that value is never set: the driver
instead computes the bFormatIndex value when linking the stream class
header in the configfs hierarchy and stores it directly in the class
descriptors in a separate structure. In order to expose the value
through the configfs attribute, store it in the config item private data
as well. This results in a small code simplification.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
The video control and video streaming interface numbers are needed in
the UVC gadget userspace stack to reply to UVC requests. They are
hardcoded to fixed values at the moment, preventing configurations with
multiple functions.
To fix this, make them dynamically discoverable by userspace through
read-only configfs attributes in <function>/control/bInterfaceNumber and
<function>/streaming/bInterfaceNumber respectively.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
The UVC configfs implementation creates all groups as global static
variables. This prevents creation of multiple UVC function instances,
as they would all require their own configfs group instances.
Fix this by allocating all groups dynamically. To avoid duplicating code
around, extend the config_item_type structure with group name and
children, and implement helper functions to create children
automatically for most groups.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Some of the .allow_link() and .drop_link() operations implementations
call config_group_find_item() and then leak the reference to the
returned item. Fix this by dropping those references where needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixed errors spaces required around the for loop '=' , ';' and '<'
in drivers/usb/storage/isd200.c
Signed-off-by: Jagdish Tirumala <t.jag587@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving all the drivers that depend on the Port Controller
Manager under a new directory drivers/usb/typec/tcpm/ and
making Guenter Roeck the designated reviewer of that code.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugfs needs to be initialized as the last step in
probe in this case. The struct dentry *rootdir can't be
pointing to anything unless driver probe really finishes
successfully.
It is also not necessary to clear the i2c clientdata if the
probe fails, so removing the extra label used for that.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not possible to use the parent of the port device when
requesting mux handles as the parent may be a multiport USB
Type-C or PD controller. The muxes must be assigned to the
ports, not the controllers.
This will also move the requesting of the muxes after the
port device is initialized.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions typec_mux_get() and typec_switch_get() already
make sure that the mux device reference count is
incremented, but the same must be done to the driver module
as well to prevent the drivers from being unloaded in the
middle of operation.
This fixes a potential "BUG: unable to handle kernel paging
request at ..." from happening.
Fixes: 93dd2112c7 ("usb: typec: mux: Get the mux identifier from function parameter")
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applying dynamic usbcore quirks in early booting when the slab is
not yet ready would cause kernel panic of null pointer dereference
because the quirk_count has been counted as 1 while the quirk_list
was failed to allocate.
i.e.,
[ 1.044970] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 1.044995] IP: [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
[ 1.045016] PGD 0
[ 1.045026] Oops: 0000 [#1] PREEMPT SMP
[ 1.046986] gsmi: Log Shutdown Reason 0x03
[ 1.046995] Modules linked in:
[ 1.047008] CPU: 0 PID: 81 Comm: kworker/0:3 Not tainted 4.4.154 #28
[ 1.047016] Hardware name: Google Coral/Coral, BIOS Google_Coral.10068.27.0 12/04/2017
[ 1.047028] Workqueue: usb_hub_wq hub_event
[ 1.047037] task: ffff88017a321c80 task.stack: ffff88017a384000
[ 1.047044] RIP: 0010:[<ffffffffb0953ec7>] [<ffffffffb0953ec7>] usb_detect_quirks+0x88/0xd1
To tackle this odd, let's balance the quirk_count to 0 when the kcalloc
call fails, and defer the quirk setting into a lower level callback
which ensures that the kernel memory management has been initialized.
Fixes: 027bd6cafd ("usb: core: Add "quirks" parameter for usbcore")
Signed-off-by: Harry Pan <harry.pan@intel.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes potential "BUG: unable to handle kernel paging
request at ..." from happening.
Fixes: fde0aa6c17 ("usb: common: Small class for USB role switches")
Cc: <stable@vger.kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in dev_dbg message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is code in the .remove() hook to handle the drvdata
being NULL, for good reasons: it is never set, so it will
always be NULL. As I moved code around, static checkers
start complaining.
Instead of this, make sure to always set it on successful
probe so we can always dereference it on the remove path.
Use the platform_device_[set|get]_drvdata() since this is
a platform device.
Fixes: ffa8a31b5b ("usb: host: fotg2: add silicon clock handling")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
R-Car Gen3 needs to enable clocks of both host and peripheral.
Since [eo]hci-platform disables the reset(s) when the drivers are
removed, renesas_usbhs driver doesn't work correctly. To fix this
issue, this patch adds multiple clocks management on this
renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
R-Car Gen3 needs to deassert resets of both host and peripheral.
Since [eo]hci-platform is possible to assert the reset(s) when
the probing failed, renesas_usbhs driver doesn't work correctly
regardless of finished probing. To fix this issue, this patch adds
reset_control on this renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB audio class 3.0 specification introduced many significant
changes like
- new power domains, support for LPM/L1
- new cluster descriptor
- new high capability and class-specific string descriptors
- BADD profiles
- ... and many other things (check spec from link below:
http://www.usb.org/developers/docs/devclass_docs/USB_Audio_v3.0.zip)
Now that UAC3 is supported in linux, choose UAC3
configuration for audio if the device supports it.
Selecting this configuration will enable the system to
save power by leveraging the new power domains and LPM L1
capability and also support new codec types and data formats
for consumer audio applications.
Signed-off-by: Saranya Gopal <saranya.gopal@intel.com>
Reviewed-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a proper PHY driver, instead of hooks to a board support package.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is done do that it could be enabled alongside other platform EHCI
glue drivers on multiplatform kernels.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As all the properties of the usbtmc driver can now be
controlled on a per file descriptor basis by ioctl functions
the sysfs interface is of limited use.
We are not aware about applications that are using the sysfs
parameter TermChar, TermCharEnabled or auto_abort.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ioctl USBTMC_IOCTL_API_VERSION to get current API version
of usbtmc driver.
This is to allow an instrument library to determine whether
the driver API is compatible with the implementation.
The API may change in future versions. Therefore the macro
USBTMC_API_VERSION should be incremented when changing tmc.h
with new flags, ioctls or when changing a significant behavior
of the driver.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use common timeout macro USB_CTRL_GET_TIMEOUT (=5s) for all
usb_control_msg() function calls.
The macro USBTMC_TIMEOUT should only be used as default value for
Bulk IN/OUT transfers.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add parameter 'tag' to function usbtmc_ioctl_abort_bulk_out_tag()
for future versions.
Use USBTMC_BUFSIZE (4k) instead of USBTMC_SIZE_IOBUFFER (2k).
Using USBTMC_SIZE_IOBUFFER is deprecated.
Insert a sleep of 50 ms between subsequent
CHECK_ABORT_BULK_OUT_STATUS control requests to avoid stressing
the instrument with repeated requests.
Use common macro USB_CTRL_GET_TIMEOUT instead of USBTMC_TIMEOUT.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add parameter 'tag' to function usbtmc_ioctl_abort_bulk_in_tag()
for future versions.
Remove calculation of max_size (=wMaxPacketSize) and wrong
condition (actual == max_size) in while loop. An abort operation
should always flush the complete Bulk-IN until a short packet is
received.
Return error code ENOMSG when transfer (specified by given tag)
is not in progress and device returns code
USBTMC_STATUS_TRANSFER_NOT_IN_PROGRESS.
Use USBTMC_BUFSIZE (4k) instead of USBTMC_SIZE_IOBUFFER (2k).
Using USBTMC_SIZE_IOBUFFER is deprecated.
Use common macro USB_CTRL_GET_TIMEOUT instead of USBTMC_TIMEOUT.
Check only bit 0 (field bmAbortBulkIn) of the
CHECK_ABORT_BULK_IN_STATUS response, since other bits are reserved
and can change in future versions.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove calculation of max_size (=wMaxPacketSize) and wrong
condition (actual == max_size) in while loop. A device clear
should always flush the complete Bulk-IN FIFO.
Insert a sleep of 50 ms between subsequent CHECK_CLEAR_STATUS
control requests to avoid stressing the instrument with
repeated requests.
Some instruments need time to cleanup internal I/O buffers.
Polling and nonbraked requests slow down the response time of
devices.
Use USBTMC_BUFSIZE (4k) instead of USBTMC_SIZE_IOBUFFER (2k).
Using USBTMC_SIZE_IOBUFFER is deprecated.
Check only bit 0 (field bmClear) of the CHECK_CLEAR_STATUS
response, since other bits are reserved and can change in
future versions.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use new usbtmc_generic_read function to maximize bandwidth
during long data transfer. Also fix reading of zero length
packet (ZLP) or trailing short packet.
The maximum input transfer size is limited to INT_MAX (=2GB).
Also remove redundant return in send_request_dev_dep_msg_in().
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use new usbtmc_generic_write function to maximize bandwidth
during long data transfer.
The maximum output transfer size is limited to INT_MAX (=2GB).
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ioctl USBTMC_IOCTL_AUTO_ABORT to configure auto_abort for
each specific file handle.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add ioctl USBTMC_IOCTL_MSG_IN_ATTR that returns the specific
bmTransferAttributes field of the last DEV_DEP_MSG_IN Bulk-IN
header. This header is received by the read() function. The
meaning of the (u8) bitmap bmTransferAttributes is:
Bit 0 = EOM flag is set when the last transfer of a USBTMC
message is received.
Bit 1 = is set when the last byte is a termchar (e.g. '\n').
Note that this bit is always zero when the device does not support
the termchar feature or when termchar detection is not enabled
(see ioctl USBTMC_IOCTL_CONFIG_TERMCHAR).
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wait until an SRQ (service request) is received on the interrupt pipe
or until the given period of time is expired. In contrast to the
poll() function this ioctl does not return when other (a)synchronous
I/O operations fail with EPOLLERR.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Submitted urbs are not allowed when system is suspended.
Thus the submitted urb waiting at interrupt pipe is killed
during suspend callback and submitted again when system resumes.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ioctl USBTMC_IOCTL_CLEANUP_IO kills all submitted urbs to OUT
and IN bulk, and clears all received data from IN bulk. Internal
transfer counters and error states are reset.
An application should use this ioctl after an asnychronous transfer
was canceled and/or error handling has finished.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioctl USBTMC_IOCTL_CANCEL_IO stops and kills all flying urbs of
last USBTMC_IOCTL_READ and USBTMC_IOCTL_WRITE function calls.
A subsequent call to USBTMC_IOCTL_READ or
USBTMC_IOCTL_WRITE_RESULT returns -ECANCELED with
information about current transferred data.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USBTMC_IOCTL_READ call provides for generic synchronous and
asynchronous reads on bulk IN to implement vendor specific library
routines.
Depending on transfer_size the function submits one or more urbs (up
to 16) each with a size of up to 4kB.
The flag USBTMC_FLAG_IGNORE_TRAILER can be used when the transmission
size is already known. Then the function does not truncate the
transfer_size to a multiple of 4 kB, but does reserve extra space
to receive the final short or zero length packet. Note that the
instrument is allowed to send up to wMaxPacketSize - 1 bytes at the
end of a message to avoid sending a zero length packet.
With flag USBTMC_FLAG_ASYNC the ioctl is non blocking. When no
received data is available, the read function submits as many urbs as
needed to receive transfer_size bytes. However the number of flying
urbs (=4kB) is limited to 16 even with subsequent calls of this ioctl.
Returns -EAGAIN when non blocking and no data is received.
Signals EPOLLIN | EPOLLRDNORM when asynchronous urbs are ready to
be read.
In non blocking mode the usbtmc_message.message pointer may be NULL
and the ioctl just submits urbs to initiate receiving data. However if
data is already available due to a previous non blocking call the ioctl
will return -EINVAL when the message pointer is NULL.
This ioctl does not support compatibility for 32 bit
applications running on 64 bit systems. However all other
convenient ioctls of the USBTMC driver can still be used in 32
bit applications as well. Note that 32 bit applications running
on 32 bit target systems are not affected by this limitation.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioctl USBTMC_IOCTL_WRITE_RESULT copies current out_transfer_size
to given __u32 pointer and returns current out_status of the last
(asnynchronous) USBTMC_IOCTL_WRITE call.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new ioctl USBTMC_IOCTL_WRITE sends a generic message to bulk OUT.
This ioctl is used for vendor specific or asynchronous I/O as well.
The message is split into chunks of 4k (page size).
Message size is aligned to 32 bit boundaries.
With flag USBTMC_FLAG_ASYNC the ioctl is non blocking.
With flag USBTMC_FLAG_APPEND additional urbs are queued and
out_status/out_transfer_size is not reset. EPOLLOUT | EPOLLWRNORM
is signaled when all submitted urbs are completed.
Flush flying urbs when file handle is closed or device is
suspended or reset.
This ioctl does not support compatibility for 32 bit
applications running on 64 bit systems. However all other
convenient ioctls of the USBTMC driver can still be used in 32
bit applications as well. Note that 32 bit applications running
on 32 bit target systems are not affected by this limitation.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add USBTMC_IOCTL_CTRL_REQUEST to send arbitrary requests on the
control pipe. Used by specific applications of IVI Foundation,
Inc. to implement VISA API functions: viUsbControlIn/Out.
The maximum length of control request is set to 4k.
This ioctl does not support compatibility for 32 bit
applications running on 64 bit systems. However all other
convenient ioctls of the USBTMC driver can still be used in 32
bit applications as well. Note that 32 bit applications running
on 32 bit target systems are not affected by this limitation.
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This update populates the tcpc handle's fwnode pointer with the
child usb-connector node, if it exists, so that TCPM can perform
generic property handling to define the ports capabilities.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_find_alt_setting() takes a pointer to a struct usb_host_config as
an argument; it searches for an interface with specified interface and
alternate setting numbers in that config. However, it crashes if the
usb_host_config pointer argument is NULL.
Since this is a general-purpose routine, available for use in many
places, we want to to be more robust. This patch makes it return NULL
whenever the config argument is NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+19c3aaef85a89d451eac@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzing project found a use-after-free bug in the USB
core. The bug was caused by usbfs not unbinding from an interface
when the USB device file was closed, which led another process to
attempt the unbind later on, after the private data structure had been
deallocated.
The reason usbfs did not unbind the interface at the appropriate time
was because it thought the interface had never been claimed in the
first place. This was caused by the fact that
usb_driver_claim_interface() does not clean up properly when
device_bind_driver() returns an error. Although the error code gets
passed back to the caller, the iface->dev.driver pointer remains set
and iface->condition remains equal to USB_INTERFACE_BOUND.
This patch adds proper error handling to usb_driver_claim_interface().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+f84aa7209ccec829536f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_driver_claim_interface() disables and re-enables Link Power
Management, but it shouldn't do either one, for the reasons listed
below. This patch removes the two LPM-related function calls from the
routine.
The reason for disabling LPM in the analogous function
usb_probe_interface() is so that drivers won't have to deal with
unwanted LPM transitions in their probe routine. But
usb_driver_claim_interface() doesn't call the driver's probe routine
(or any other callbacks), so that reason doesn't apply here.
Furthermore, no driver other than usbfs will ever call
usb_driver_claim_interface() unless it is already bound to another
interface in the same device, which means disabling LPM here would be
redundant. usbfs doesn't interact with LPM at all.
Lastly, the error return from usb_unlocked_disable_lpm() isn't handled
properly; the code doesn't clean up its earlier actions before
returning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8306095fd2 ("USB: Disable USB 3.0 LPM in critical sections.")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we filter flags before they reach the core we need to generate our
own warnings.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 0cb54a3e47 ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting a ZERO_PACKET or not is sensible only for output.
In the input direction the device decides.
Likewise accepting short packets makes sense only for input.
This allows operation with panic_on_warn without opening up
a local DOS.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+843efa30c8821bd69f53@syzkaller.appspotmail.com
Fixes: 0cb54a3e47 ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6e22e3af7b.
The bug the patch describes to, has been already fixed in commit
2df6948428 ("USB: cdc-wdm: don't enable interrupts in USB-giveback")
so need to this, revert it.
Fixes: 6e22e3af7b ("usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TI AM335x CPPI 4.1 module uses a single register bit for CPPI interrupts
in both musb controllers. So disabling the CPPI irq in one musb driver
breaks the other musb module.
Since musb is already disabled before tearing down dma controller in
musb_remove(), it is safe to not disable CPPI irq in
musb_dma_controller_destroy().
Fixes: 255348289f ("usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At OTG work running time, it's possible that several events need to be
addressed (e.g. ID and VBUS events). The current implementation handles
only one event at a time which leads to ignoring the other one. Fix it.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The ChipIdea IRQ is disabled before scheduling the otg work and
re-enabled on otg work completion. However if the job is already
scheduled we have to undo the effect of disable_irq int order to
balance the IRQ disable-depth value.
Fixes: be6b0c1bd0 ("usb: chipidea: using one inline function to cover queue work operations")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some hardware implementations require to configure pins differently
according to the USB role (host/device), this can be an update of the
pins routing or a simple GPIO value change.
This patch introduces new optional "host" and "device" pinctrls.
If these pinctrls are defined by the device, they are respectively
selected on host/device role start.
If a default pinctrl exist, it is restored on host/device role stop.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The SPDX-License-Identifier is set to GPL-2.0+, which correspond to
MODULE_LICENSE "GPL".
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
When initializing the USB subsystem before starting the kernel,
OTG overcurrent detection is disabled. In case the OTG polarity of
overcurrent is low active, the overcurrent detection is never enabled
again and events cannot be reported as expected. Because imx usb
overcurrent polarity is low active by default, only detection needs
to be enable in usbmisc init function.
Signed-off-by: Nicolas Adell <nicolas.adell@actia.fr>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Use preprocessor conditionals for CONFIG_PM and CONFIG_PM_SLEEP is
not necessary since SET_SYSTEM_SLEEP_PM_OPS and SET_RUNTIME_PM_OPS does
that internally.
It is also the preferred way according to our coding style guidelines.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The UVC configfs implementation is large and difficult to navigate. Add
a bit more air to the code to make it easier to read.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Various configfs groups (represented by config_group) are wrapped in
structures that they're the only member of. This allows adding other
data fields to groups, but it unnecessarily makes the code more complex.
Remove the outer structures and use config_group directly to simplify
the code. Groups can still be wrapped individually in the future if
other data fields need to be added.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
These ioctls never reach driver's ->ioctl() - tty_ioctl() handles
them on its own. ->tiocm[gs]et() is what actually gets called,
and mos7720 provides those, with results equivalent to what the
unreachable code would be doing when called.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Allow matching on interfaces having two endpoints by adding a new
device-id flag.
This allows for the handling of devices whose interface numbers can
change (e.g. Quectel EP06) to be contained in the device-id table.
Tested-by: Kristian Evensen <kristian.evensen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Quectel EP06 (and EM06/EG06) LTE modem supports updating the USB
configuration, without the VID/PID or configuration number changing.
When the configuration is updated and interfaces are added/removed, the
interface numbers are updated. This causes our current code for matching
EP06 not to work as intended, as the assumption about reserved
interfaces no longer holds. If for example the diagnostic (first)
interface is removed, option will (try to) bind to the QMI interface.
This patch improves EP06 detection by replacing the current match with
two matches, and those matches check class, subclass and protocol as
well as VID and PID. The diag interface exports class, subclass and
protocol as 0xff. For the other serial interfaces, class is 0xff and
subclass and protocol are both 0x0.
The modem can export the following devices and always in this order:
diag, nmea, at, ppp. qmi and adb. This means that diag can only ever be
interface 0, and interface numbers 1-5 should be marked as reserved. The
three other serial devices can have interface numbers 0-3, but I have
not marked any interfaces as reserved. The reason is that the serial
devices are the only interfaces exported by the device where subclass
and protocol is 0x0.
QMI exports the same class, subclass and protocol values as the diag
interface. However, the two interfaces have different number of
endpoints, QMI has three and diag two. I have added a check for number
of interfaces if VID/PID matches the EP06, and we ignore the device if
number of interfaces equals three (and subclass is set).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
[ johan: drop uneeded RSVD(5) for ADB ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Today kernel threads never dequeue siginfo so it is pointless to
enqueue siginfo for them. The usb gadget mass storage driver goes
one farther and uses SEND_SIG_FORCED to guarantee that no siginfo is
even enqueued.
Generalize the optimization of the usb mass storage driver and never
perform an unnecessary allocation when delivering signals to kthreads.
Switch the mass storage driver from sending signals with
SEND_SIG_FORCED to SEND_SIG_PRIV. As using SEND_SIG_FORCED is now
unnecessary.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
None of the callers use the it so remove it.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
In commit ed194d1367 ("usb: core: remove local_irq_save() around
->complete() handler") I removed the only user of the flags variable and
forgot to remove the variable, leading to warning because it is unused
now.
Remove the unused variable.
Fixes: ed194d1367 ("usb: core: remove local_irq_save() around ->complete() handler")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a81cf9799a.
The patch causes a regression, which I cannot find the reason for.
So let's revert for now, as a revert hurts only performance.
Original report:
I was trying to resolve the problem with Oliver but we don't get any conclusion
for 5 months, so I am now sending this to mail list and cdc_acm authors.
I am using simple request-response protocol to obtain the boiller parameters
in constant intervals.
A simple one transaction is:
1. opening the /dev/ttyACM0
2. sending the following 10-bytes request to the device:
unsigned char req[] = {0x02, 0xfe, 0x01, 0x05, 0x08, 0x02, 0x01, 0x69, 0xab, 0x03};
3. reading response (frame of 74 bytes length).
4. closing the descriptor
I am doing this transaction with 5 seconds intervals.
Before the bad commit everything was working correctly: I've got a requests and
a responses in a timely manner.
After the bad commit more time I am using the kernel module, more problems I have.
The graph [2] is showing the problem.
As you can see after module load all seems fine but after about 30 minutes I've got
a plenty of EAGAINs when doing read()'s and trying to read back the data.
When I rmmod and insmod the cdc_acm module again, then the situation is starting
over again: running ok shortly after load, and more time it is running, more EAGAINs
I have when calling read().
As a bonus I can see the problem on the device itself:
The device is configured as you can see here on this screen [3].
It has two transmision LEDs: TX and RX. Blink duration is set for 100ms.
This is a recording before the bad commit when all is working fine: [4]
And this is with the bad commit: [5]
As you can see the TX led is blinking wrongly long (indicating transmission?)
and I have problems doing read() calls (EAGAIN).
Reported-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: a81cf9799a ("cdc-acm: implement put_char() and flush_chars()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since renesas_usb3 udc driver calls usb_of_get_companion_dev()
which is on usb/core/of.c, build error like below happens if we
disable CONFIG_USB because the usb/core/ needs CONFIG_USB:
ERROR: "usb_of_get_companion_dev" [drivers/usb/gadget/udc/renesas_usb3.ko] undefined!
According to the usb/gadget/Kconfig, "NOTE: Gadget support
** DOES NOT ** depend on host-side CONFIG_USB !!".
So, to fix the issue, this patch changes the usb_of_get_companion_dev()
place from usb/core/of.c to usb/common/common.c to be called by both
host and gadget.
Reported-by: John Garry <john.garry@huawei.com>
Fixes: 39facfa01c ("usb: gadget: udc: renesas_usb3: Add register of usb role switch")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MTK xHCI controller use some reserved bytes in endpoint context for
bandwidth scheduling, so need keep them in xhci_endpoint_copy();
The issue is introduced by:
commit f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
It resets endpoints and will drop bandwidth scheduling parameters used
by interrupt or isochronous endpoints on MTK xHCI controller.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use IS_ERR() instead of IS_ERR_OR_NULL() because devm_of_phy_get_by_index()
never return NULL value;
But still need ignore the error of -ENODEV, for more information, please
refer to:
[0] https://lkml.org/lkml/2018/4/19/88
[1] https://patchwork.kernel.org/patch/10160181/
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vbus rise & fall interrupts are used to enable and disable
U3 function of device automatically, this cause some issues when
class driver is initialized as deactivated, and will skip over
software-controlled connect by pullup(), but UDC wants to keep
disconnect until usb_gadget_activate() is called which calls
pullup() if needed. So we disable vbus rise & fall interrupts
and just use pullup() to enable & disable U3 function, and reset
mtu3 state when disconnect instead when vbus fall.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
simple_strtoul is obsolete, and use kstrtoint instead
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A common flaw in the kernel is integer overflow during memory allocation
size calculations. In an effort to reduce the frequency of these bugs,
kmalloc_array was implemented, which allocates memory for an array,
while at the same time detects integer overflow.
This patch replaces cases of:
kmalloc(a * b, gfp)
with:
kmalloc_array(a, b, gfp)
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul pointed out that the 50-ms sleep during OHCI initialization takes
up a large fraction of a system's boot time. Things get worse when
there are two OHCI controllers present, each requiring 50 ms.
However, there really is no need to send a 50-ms reset signal out all
the root-hub ports during initialization. The ports themselves will
be disabled, and the only way to enable a port is to reset it.
Therefore all attached USB devices will receive a proper reset in any
case. The controller reset does not need to be long enough to reset
those other devices, so the 50-ms delay isn't necessary.
Without the delay, there is no remaining incentive for skipping the
reset when the controller is already in the RESET state. This patch
removes the test, issuing the command unconditionally, and removes the
following delay.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When used in a system with software-controlled silicon clocks,
the FOTG210 needs to grab, prepare and enable the clock.
This is needed on for example the Cortina Gemini, where the
platform will by default gate off the clock unless the
peripheral (in this case the USB driver) grabs and enables
the clock.
If there is no clock available on the platform, we live
without it. Make sure to percolate probe deferrals.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variables snk_pdo and toggling_mode_name are defined but are not used and
hence can be removed.
Cleans up clang warnings:
warning: 'snk_pdo' defined but not used [-Wunused-const-variable=]
warning: 'toggling_mode_name' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because USB_STORAGE build symbol strictly depends on SCSI build
symbol, there is no need to specify it again.
In addition USB_STORAGE_ENE_UB6250 entry description repeats a note
about SCSI dependency from the parent USB_STORAGE entry description,
hence the change removes this duplication.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of explicit setting of USB_STORAGE dependency for every
underlying build entries, exploit if USB_STORAGE / endif block.
The change is a trivial non-functional cleanup, it shortens
the Kconfig file and it is expected to reduce zconf parser
workload a little.
Dependencies of USB_UAS build option are left aside deliberately.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing NULL check for pool since dma_pool_destroy is safe
Signed-off-by: Salil Kapur <salilkapur93@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core disabled interrupts before invocation the ->complete handler
because the handler might have expected that interrupts are disabled.
All handlers were audited and use proper locking now. With it, the core
code no longer needs to disable interrupts before invoking the
->complete handler.
Remove local_irq_save() statement before invoking the ->complete
handler.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
-----BEGIN PGP SIGNATURE-----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=bEhk
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.19-rc2
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
Here are two fixes for array-underflow bugs in completion handlers due
to insufficient sanity checks.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XYLd
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.19-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.19-rc3
Here are two fixes for array-underflow bugs in completion handlers due
to insufficient sanity checks.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
wdm_in_callback() is a completion handler function for the USB driver.
So it should not sleep. But it calls service_outstanding_interrupt(),
which calls usb_submit_urb() with GFP_KERNEL.
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
async_complete() in uss720.c is a completion handler function for the
USB driver. So it should not sleep, but it is can sleep according to the
function call paths (from bottom to top) in Linux-4.16.
[FUNC] set_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 372:
set_1284_register in parport_uss720_frob_control
drivers/parport/ieee1284.c, 560:
[FUNC_PTR]parport_uss720_frob_control in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
[FUNC] get_1284_register(GFP_KERNEL)
drivers/usb/misc/uss720.c, 382:
get_1284_register in parport_uss720_read_status
drivers/parport/ieee1284.c, 555:
[FUNC_PTR]parport_uss720_read_status in parport_ieee1284_ack_data_avail
drivers/parport/ieee1284.c, 577:
parport_ieee1284_ack_data_avail in parport_ieee1284_interrupt
./include/linux/parport.h, 474:
parport_ieee1284_interrupt in parport_generic_irq
drivers/usb/misc/uss720.c, 116:
parport_generic_irq in async_complete
Note that [FUNC_PTR] means a function pointer call is used.
To fix these bugs, GFP_KERNEL is replaced with GFP_ATOMIC.
These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i_usX2Y_subs_startup in usbusx2yaudio.c is a completion handler function
for the USB driver. So it should not sleep, but it is can sleep
according to the function call paths (from bottom to top) in Linux-4.16.
[FUNC] msleep
drivers/usb/host/u132-hcd.c, 2558:
msleep in u132_get_frame
drivers/usb/core/hcd.c, 2231:
[FUNC_PTR]u132_get_frame in usb_hcd_get_frame_number
drivers/usb/core/usb.c, 822:
usb_hcd_get_frame_number in usb_get_current_frame_number
sound/usb/usx2y/usbusx2yaudio.c, 303:
usb_get_current_frame_number in i_usX2Y_urb_complete
sound/usb/usx2y/usbusx2yaudio.c, 366:
i_usX2Y_urb_complete in i_usX2Y_subs_startup
Note that [FUNC_PTR] means a function pointer call is used.
To fix this bug, msleep() is replaced with mdelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The steps taken by usb core to set a new interface is very different from
what is done on the xHC host side.
xHC hardware will do everything in one go. One command is used to set up
new endpoints, free old endpoints, check bandwidth, and run the new
endpoints.
All this is done by xHC when usb core asks the hcd to check for
available bandwidth. At this point usb core has not yet flushed the old
endpoints, which will cause use-after-free issues in xhci driver as
queued URBs are cancelled on a re-allocated endpoint.
To resolve this add a call to usb_disable_interface() which will flush
the endpoints before calling usb_hcd_alloc_bandwidth()
Additional checks in xhci driver will also be implemented to gracefully
handle stale URB cancel on freed and re-allocated endpoints
Cc: <stable@vger.kernel.org>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kernel-doc warning for missing function parameter 'mode' description:
../drivers/usb/typec/bus.c:268: warning: Function parameter or member 'mode' not described in 'typec_match_altmode'
Also fix typos for same function documentation.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hc_died() should only be called once, and with the primary HCD
as parameter. It will mark both primary and secondary hcd's dead.
Remove the extra call to usb_cd_died with the shared hcd as parameter.
Fixes: ff9d78b36f ("USB: Set usb_hcd->state and flags for shared roothubs")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dual role mode is enabled, when switch u3port0 to device mode,
it will affect port id calculation of host(xHCI), specially when
host supports multi U2 ports or U3 ports, so need enable its dual
role mode, and fix it here.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hope that UAS devices would be less broken than old style storage
devices has turned out to be unfounded. Make UAS support more of the
quirk flags of the old driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device does not correctly handle the LPM operations.
Also, the device cannot handle ATA pass-through commands
and locks up when attempted while running in super speed.
This patch adds the equivalent quirk logic as found in uas.
Signed-off-by: Tim Anderson <tsa@biglakesoftware.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snprintf() always returns the full length of the string it could have
printed, even if it was truncated because the buffer was too small.
So in case the counter value is truncated, we will over-read from
in_buffer and over-write to the caller's buffer.
I don't think it's actually possible for this to happen, but in case
truncation occurs, WARN and return -EIO.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the written data starts with a digit, yurex_write() tries to parse
it as an integer using simple_strtoull(). This requires a null-
terminator, and currently there's no guarantee that there is one.
(The sample program at
https://github.com/NeoCat/YUREX-driver-for-Linux/blob/master/sample/yurex_clock.pl
writes an integer without a null terminator. It seems like it must
have worked by chance!)
Always add a null byte after the written data. Enlarge the buffer
to allow for this.
Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In xhci_plat_probe() both sysdev and pdev->dev are being used
for finding quirks. There are some drivers(like dwc3 host.c)
which adds quirks(like usb3-lpm-capable) into pdev and the logic
present in xhci_plat_probe() checks for quirks in either sysdev
or pdev for finding the quirks. Because of this logic, some of
the quirks are getting missed(usb3-lpm-capable quirk added by dwc3
host.c driver is getting missed).This patch fixes this by iterating
over all the available parents for finding the quirks. In this way
all the quirks which are present in child or parent are correctly
updated.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the cancelled URB is on the current endpoint ring.
If the endpoint ring has been reallocated since the URB was enqueued
then the URB may contain TD and TRB pointers to a already freed ring.
In this the case return the URB without touching any of the freed ring
structure data.
Don't try to stop the ring. It would be useless.
This can occur if endpoint is not flushed before it is dropped and
re-added, which is the case in usb_set_interface() as xhci does
things in an odd order.
Cc: <stable@vger.kernel.org>
Tested-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WORLDE Controller KS49 or Prodipe MIDI 49C USB controller
cause a -EPROTO error, a communication restart and loop again.
This issue has already been fixed for KS25.
https://lore.kernel.org/patchwork/patch/753077/
I just add device 201 for KS49 in quirks.c to get it works.
Signed-off-by: Laurent Roux <xpros64@hotmail.fr>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoC/IP as STM32F469, the snpsid can only be read after clock is
enabled, otherwise it will read as 0, and the dwc2_check_core_endianness
will assume the core and AHB have opposite endianness, leading to the
following error:
[ 1.976339] dwc2 50000000.usb: 50000000.usb supply vusb_d not found, using dummy regulator
[ 1.986124] dwc2 50000000.usb: Linked as a consumer to regulator.0
[ 1.992711] dwc2 50000000.usb: 50000000.usb supply vusb_a not found, using dummy regulator
[ 2.003672] dwc2 50000000.usb: dwc2_core_reset: HANG! AHB Idle timeout GRSTCTL GRSTCTL_AHBIDLE
[ 2.015176] dwc2: probe of 50000000.usb failed with error -16
The proposed patch changes the location where dwc2_check_core_endianness
is called, allowing the clock peripheral to be enabled first.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Bruno Meirelles Herrera <bmh@certi.org.br>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This implements the V4L2 part of the request support. The main
change is that vb2_qbuf and vb2_prepare_buf now have a new
media_device pointer. This required changes to several drivers
that did not use the vb2_ioctl_qbuf/prepare_buf helper functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of error, the function pcim_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 7740d04d90 ("usb: dwc3: pci: Enable ULPI Refclk on platforms where the firmware does not")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that maxpacket size of ep0 is incorrect
for SuperSpeed. Otherwise, CDC NCM class with SuperSpeed doesn't
work correctly on this driver because its control read data size
is more than 64 bytes.
Reported-by: Junki Kato <junki.kato.xk@renesas.com>
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Junki Kato <junki.kato.xk@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no deallocation of fotg210->ep[i] elements, allocated at
fotg210_udc_probe.
The patch adds deallocation of fotg210->ep array elements and simplifies
error path of fotg210_udc_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit f16443a034 ("USB: gadgetfs, dummy-hcd, net2280: fix locking
for callbacks") was based on a serious misunderstanding. It
introduced regressions into both the dummy-hcd and net2280 drivers.
The problem in dummy-hcd was fixed by commit 7dbd8f4cab ("USB:
dummy-hcd: Fix erroneous synchronization change"), but the problem in
net2280 remains. Namely: the ->disconnect(), ->suspend(), ->resume(),
and ->reset() callbacks must be invoked without the private lock held;
otherwise a deadlock will occur when the callback routine tries to
interact with the UDC driver.
This patch largely is a reversion of the relevant parts of
f16443a034. It also drops the private lock around the calls to
->suspend() and ->resume() (something the earlier patch forgot to do).
This is safe from races with device interrupts because it occurs
within the interrupt handler.
Finally, the patch changes where the ->disconnect() callback is
invoked when net2280_pullup() turns the pullup off. Rather than
making the callback from within stop_activity() at a time when dropping
the private lock could be unsafe, the callback is moved to a point
after the lock has already been dropped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: f16443a034 ("USB: gadgetfs, dummy-hcd, net2280: fix locking for callbacks")
Reported-by: D. Ziesche <dziesche@zes.com>
Tested-by: D. Ziesche <dziesche@zes.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
An incorrect #ifdef caused a pair of harmless warnings when CONFIG_PM_SLEEP
is disabled:
drivers/usb/dwc3/dwc3-of-simple.c:223:12: error: 'dwc3_of_simple_resume' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-of-simple.c:213:12: error: 'dwc3_of_simple_suspend' defined but not used [-Werror=unused-function]
static int dwc3_of_simple_suspend(struct device *dev)
Since the #ifdef method is generally hard to get right, use
a simpler __maybe_unused annotation here to let the compiler
drop the unused functions silently. This also improves
compile-time coverage.
Fixes: 76251db865 ("usb: dwc3: of-simple: reset host controller at suspend/resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Similarly to a recently reported bug in io_ti, a malicious USB device
could set port_number to a negative value and we would underflow the
port array in the interrupt completion handler.
As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
As reported by Dan Carpenter, a malicious USB device could set
port_number to a negative value and we would underflow the port array in
the interrupt completion handler.
As these devices only have one or two ports, fix this by making sure we
only consider the seventh bit when determining the port number (and
ignore bits 0xb0 which are typically set to 0x30).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC
-----BEGIN PGP SIGNATURE-----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=ZjwY
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this development
cycle:
- lots of type-c work, with drivers graduating out of staging,
and displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot
simpler in the future.
- usbserial driver fixes and reworks
- other misc changes
Full details are in the shortlog.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3hBPA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yloNwCggMZi9m8Krjq7d7aLw5oJJex/nIAAn0jeADOT
NpoCgrtGHjwrATxN5/Ke
=jXa3
-----END PGP SIGNATURE-----
Merge tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this
development cycle:
- lots of type-c work, with drivers graduating out of staging, and
displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot simpler in
the future.
- usbserial driver fixes and reworks
- other misc changes
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: serial: pl2303: add a new device id for ATEN
usb: renesas_usbhs: Kconfig: convert to SPDX identifiers
usb: dwc3: gadget: Check MaxPacketSize from descriptor
usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms
usb: dwc2: Turn on uframe_sched on "amlogic" platforms
usb: dwc2: Turn on uframe_sched on "his" platforms
usb: dwc2: Turn on uframe_sched on "bcm" platforms
usb: dwc2: gadget: ISOC's starting flow improvement
usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.
usb: dwc3: core: Enable AutoRetry feature in the controller
usb: dwc3: Set default mode for dwc_usb31
usb: gadget: udc: renesas_usb3: Add register of usb role switch
usb: dwc2: replace ioread32/iowrite32_rep with dwc2_readl/writel_rep
usb: dwc2: Modify dwc2_readl/writel functions prototype
usb: dwc3: pci: Intel Merrifield can be host
usb: dwc3: pci: Supply device properties via driver data
arm64: dts: dwc3: description of incr burst type
usb: dwc3: Enable undefined length INCR burst type
usb: dwc3: add global soc bus configuration reg0
usb: dwc3: Describe 'wakeup_work' field of struct dwc3_pci
...
Notable changes:
- A fix for a bug in our page table fragment allocator, where a page table page
could be freed and reallocated for something else while still in use, leading
to memory corruption etc. The fix reuses pt_mm in struct page (x86 only) for
a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but bring us in
to line with x86 behaviour and/or fix outright bugs. Thanks to Florian Weimer
for reporting many of these.
- A series to improve the hvc driver & related OPAL console code, which have
been seen to cause hardlockups at times. The hvc driver changes in particular
have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in use
anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM CPUs
(controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals to bring it
into line with other arches, including showing the offending VMA and dumping
the instructions around the fault.
Thanks to:
Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Alexey
Spirkov, Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
Arnd Bergmann, Bartosz Golaszewski, Benjamin Herrenschmidt, Bharat Bhushan,
Bjoern Noetel, Boqun Feng, Breno Leitao, Bryant G. Ly, Camelia Groza,
Christophe Leroy, Christoph Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt,
Darren Stevens, Dave Young, David Gibson, Diana Craciun, Finn Thain, Florian
Weimer, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel Stanley,
Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh Salgaonkar, Markus
Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues, Michael Hanselmann, Michael
Neuling, Michael Schmitz, Mukesh Ojha, Murilo Opsfelder Araujo, Nicholas
Piggin, Parth Y Shah, Paul Mackerras, Paul Menzel, Ram Pai, Randy Dunlap,
Rashmica Gupta, Reza Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff,
Scott Wood, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson,
Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat Rao
B, zhong jiang.
-----BEGIN PGP SIGNATURE-----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=PzRz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A fix for a bug in our page table fragment allocator, where a page
table page could be freed and reallocated for something else while
still in use, leading to memory corruption etc. The fix reuses
pt_mm in struct page (x86 only) for a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but
bring us in to line with x86 behaviour and/or fix outright bugs.
Thanks to Florian Weimer for reporting many of these.
- A series to improve the hvc driver & related OPAL console code,
which have been seen to cause hardlockups at times. The hvc driver
changes in particular have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
use anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX
instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM
CPUs (controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals
to bring it into line with other arches, including showing the
offending VMA and dumping the instructions around the fault.
Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
Rao, zhong jiang"
* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
powerpc/mm/book3s/radix: Add mapping statistics
powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
powerpc/mm/hash: Remove unnecessary do { } while(0) loop
powerpc/64s: move machine check SLB flushing to mm/slb.c
powerpc/powernv/idle: Fix build error
powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
powerpc/mm: remove warning about ‘type’ being set
powerpc/32: Include setup.h header file to fix warnings
powerpc: Move `path` variable inside DEBUG_PROM
powerpc/powermac: Make some functions static
powerpc/powermac: Remove variable x that's never read
cxl: remove a dead branch
powerpc/powermac: Add missing include of header pmac.h
powerpc/kexec: Use common error handling code in setup_new_fdt()
powerpc/xmon: Add address lookup for percpu symbols
powerpc/mm: remove huge_pte_offset_and_shift() prototype
powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
powerpc/fadump: handle crash memory ranges array index overflow
...
This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the
continuing absence of Nic we have target updates for tcmu and target
core (all with reviews and acks). The biggest observable change is
going to be that we're (again) trying to switch to mulitqueue as the
default (a user can still override the setting on the kernel command
line). Other major core stuff is the removal of the remaining
Microchannel drivers, an update of the internal timers and some
reworks of completion and result handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW3R3niYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishauRAP4yfBKK
dbxF81c/Bxi/Stk16FWkOOrjs4CizwmnMcpM5wD/UmM9o6ebDzaYpZgA8wIl7X/N
o/JckEZZpIp+5NySZNc=
=ggLB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr.
In addition, with the continuing absence of Nic we have target updates
for tcmu and target core (all with reviews and acks).
The biggest observable change is going to be that we're (again) trying
to switch to mulitqueue as the default (a user can still override the
setting on the kernel command line).
Other major core stuff is the removal of the remaining Microchannel
drivers, an update of the internal timers and some reworks of
completion and result handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue
scsi: ufs: remove unnecessary query(DM) UPIU trace
scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done()
scsi: aacraid: Spelling fix in comment
scsi: mpt3sas: Fix calltrace observed while running IO & reset
scsi: aic94xx: fix an error code in aic94xx_init()
scsi: st: remove redundant pointer STbuffer
scsi: qla2xxx: Update driver version to 10.00.00.08-k
scsi: qla2xxx: Migrate NVME N2N handling into state machine
scsi: qla2xxx: Save frame payload size from ICB
scsi: qla2xxx: Fix stalled relogin
scsi: qla2xxx: Fix race between switch cmd completion and timeout
scsi: qla2xxx: Fix Management Server NPort handle reservation logic
scsi: qla2xxx: Flush mailbox commands on chip reset
scsi: qla2xxx: Fix unintended Logout
scsi: qla2xxx: Fix session state stuck in Get Port DB
scsi: qla2xxx: Fix redundant fc_rport registration
scsi: qla2xxx: Silent erroneous message
scsi: qla2xxx: Prevent sysfs access when chip is down
scsi: qla2xxx: Add longer window for chip reset
...
-----BEGIN PGP SIGNATURE-----
iJEEABYIADkWIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCW3HajRscamFjZWsuYW5h
c3pld3NraUBnbWFpbC5jb20ACgkQYhBsURv0pdvxAwEA+qS5O9ByxlhT+BUC4ck6
nIy0ITOCXP8ySoo8VVhzjikBAPrb9lFYGvHqzKN4dYtnSILPmlTSf1t1flng2Zev
NfoE
=lNwq
-----END PGP SIGNATURE-----
Merge tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"LED triggers improvements make the biggest part of this pull request.
The most striking ones, that allowed for nice cleanups in the triggers
are:
- centralized handling of creation and removal of trigger sysfs
attributes via attribute group
- addition of module_led_trigger() helper
The other things that need to be mentioned:
New features and improvements to existing LED class drivers:
- lt3593: add DT support, switch to gpiod interface
- lm3692x: support LED sync configuration, change OF calls to fwnode
calls
- apu: modify PC Engines apu/apu2 driver to support apu3
Change in the drivers/net/can/led.c:
- mark led trigger as broken since it's in the way for the further
cleanups. It implements a subset of the netdev trigger and an Ack
is needed from someone who can actually test and confirm that the
netdev trigger works for can devices"
* tag 'leds-for-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (32 commits)
leds: ns2: Change unsigned to unsigned int
usb: simplify usbport trigger
leds: gpio trigger: simplifications from core changes
leds: backlight trigger: simplifications from core changes
leds: activity trigger: simplifications from core changes
leds: default-on trigger: make use of module_led_trigger()
leds: heartbeat trigger: simplifications from core changes
leds: oneshot trigger: simplifications from core changes
leds: transient trigger: simplifications from core changes
leds: timer trigger: simplifications from core changes
leds: netdev trigger: simplifications from core changes
leds: triggers: new function led_set_trigger_data()
leds: triggers: define module_led_trigger helper
leds: triggers: handle .trigger_data and .activated() in the core
leds: triggers: add device attribute support
leds: triggers: let struct led_trigger::activate() return an error code
leds: triggers: make the MODULE_LICENSE string match the actual license
leds: lm3692x: Support LED sync configuration
dt: bindings: lm3692x: Update binding for LED sync control
leds: lm3692x: Change DT calls to fwnode calls
...
This converts drivers that were only calling transport_deregister_session
to use target_remove_session. The calling of
transport_deregister_session_configfs via target_remove_session for these
types of drivers is ok, because they were not exporting info from fields
like sess_acl_list, sess->se_tpg and sess->fabric_sess_ptr from configfs
accessible functions, so they will see no difference.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename target_alloc_session to target_setup_session to avoid confusion with
the other transport session allocation function that only allocates the
session and because the target_alloc_session does so much more. It
allocates the session, sets up the nacl and registers the session.
The next patch will then add a remove function to match the setup in this
one, so it should make sense for all drivers, except iscsi, to just call
those 2 functions to setup and remove a session.
iscsi will continue to be the odd driver.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Chris Boot <bootc@bootc.net>
Cc: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Cc: Michael Cyr <mikecyr@linux.vnet.ibm.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Movie Song <MovieSong@aten-itlab.cn>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
-----BEGIN PGP SIGNATURE-----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=HiNz
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.19
Not a big pull request with only 37 non-merge commits, most of which
are touching dwc2 (74% of the changes).
The most important changes are dwc2's support for uframe scheduling
and its endian-agnostic readl/writel wrappers.
From dwc3 side we have a special new glue layer for Synopsys HAPS
which will help Synopsys running FPGA validation using our upstream
driver. We also have the beginnings of dual-role support for Intel
Merrifield platform.
Apart from these, just a series of non-critical changes.
endpoint->maxpacket is not updated after setting the
usb_set_maxpacket_limit() on endpoint enable. The MaxPacketSize can be
different than the endpoint->maxpacket_limit.
DWC3 has been consistently using MaxPacketSize from the endpoint's
descriptor, so let's keep it consistent and use the MaxPacketSize from
the endpoint's descriptor instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on stm32f4x9_fsotg since commit
e35b135055 ("usb: dwc2: Add support for STM32F429/439/469 USB OTG
HS/FS in FS mode (internal PHY)"). That commit is pretty recent, so
it's unclear to me why the uframe scheduler was left off. Hopefully
it's because someone copied it from other parameters and didn't think
to try it?
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on Amlogic since commit f94310ac07
("usb: dwc2: add support for Meson8b and GXBB SoCs"). While this was
after most of the recent improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler"), presumably
the parameters were copied from another platform and the uframe
scheduler wasn't tried.
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on HiSilicon since commit
37dd9d65cc ("usb: dwc2: add support of hi6220"). Since then there
have been many many improvements, notably the commit 9f9f09b048
("usb: dwc2: host: Totally redo the microframe scheduler")
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's no reason to have the uframe scheduler off on dwc2. Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".
The uframe scheduler has been off on Broadcom since commit
58b179dcf2 ("staging: dwc2: disable uframe_sched on the bcm2835").
Since then there have been many many improvements, notably the commit
9f9f09b048 ("usb: dwc2: host: Totally redo the microframe
scheduler")
Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To start ISOC transfers in handlers dwc2_gadget_handle_nak() and
dwc2_gadget_handle_out_token_ep_disabled() driver reads current frame
number, based on which, set target frame number to start first ISOC
transfer.
In case if system's high IRQ latency and multiple EP's asserted
interrupt in same frame, there are high probability that when reading
current frame number in EP's handlers, actual frame number can be
increased. As result for bInterval > 1, starting target frame
will be set wrongly and all ISOC packets will be dropped.
In patch "usb: dwc2: Change reading of current frame number flow"
reading of current frame number done ASAP in common interrupt handler.
This frame number stored in frame_number variable which used as
starting frame number for ISOC EP's in above mentioned handlers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Declared dwc2_check_core_endianness() function for dynamicly check
core endianness.
Added needs_byte_swap flag to hsotg structure, and depending on
flag swap value inside dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By default when core sees any transaction error (CRC or overflow) it
replies with terminating retry ACK (Retry=1 and Nump == 0).
Enabling this Auto Retry feature in controller will make the core send
a non-terminanting ACK upon such transaction errors. That is, ACK TP
with Retry=1 and Nump != 0.
Doing so will give controller a chance to recover from transient error
conditions.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc_usb31 does not support OTG mode. If the controller supports DRD but
the dr_mode is not specified or set to OTG, then set the mode to
peripheral.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds role switch support for R-Car SoCs into the USB 3.0
peripheral driver. Some R-Car SoCs (e.g. R-Car H3) have USB 3.0
dual-role device controller which has the USB 3.0 xHCI host and
Renesas USB 3.0 peripheral.
Unfortunately, the mode change register (DRD_CON) contains
the USB 3.0 peripheral controller side only. So, this renesas_usb3
driver manages the DRD_CON now. However, in peripheral mode, the host
should stop. Also the host hardware needs to reinitialize its own
registers when the mode changes from peripheral to host mode.
Otherwise, the host cannot work correctly (e.g. detect a device
as high-speed).
To achieve this reinitialization by a driver, this driver also
registers a role switch driver to manage the DRD_CON and get
a device pointer of usb 3.0 host from "companion" property of OF.
Then, when the usb role is changed, renesas_usb3_role_switch_set()
will attach/release the xhci-plat driver to reinitialize the host
hardware.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_readl_rep/dwc2_writel_rep functions using readl/writel in a
loop.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added hsotg argument to dwc2_readl/writel function prototype,
and also instead of address pass offset of register.
hsotg will contain flag field for endianness.
Also customized dwc2_set_bit and dwc2_clear_bit function for
dwc2_readl/writel functions.
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On Intel Edison board the OTG function is enabled, thus,
USB can switch to the host mode.
Allow that by changing dr_mode property to "otg" for Intel Merrifield.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For now all PCI enumerated dwc3 devices require some properties
to be present. This allows us to unconditionally append them and supply
via driver_data.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add the macro definition for global soc bus configuration
register 0
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Pengbo Mu <pengbo.mu@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Describe 'wakeup_work' field of struct dwc3_pci to avoid a warning:
drivers/usb/dwc3/dwc3-pci.c:59: warning: Function parameter or member 'wakeup_work' not described in 'dwc3_pci'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJbWo96ExxwZXRlci5jaGVuQG54cC5jb20ACgkQSFkpgVDWcbv9
BwgAnNcotaqyTwAe1/Zq/enT3i49yeQmKyj1+OC1LKBqyAKp5IcSzx/9o+FqYWhC
YB+Sdy51Qq/7MsRNE2OdQFkJ/FmL2k7acc+oF9eBeMQ/EqU7nZGjs8jQrHUQ/R/I
6QpFguXIPgiwtRUyAEWGM7LIGc8a76GFXBJZALISzQRvj5WK7efO1ZwqLd1ELcJm
BuGtZ85WDEinuXAXKyjAyuF9tOIh5Y67/9JQ1slzj4WDhdnpN2ULBu3tFIPUROvo
755pX+K5WiKpST4BeX77VaCKj2pAgANE0YWJDLfGYlkoWyR/Y1mA0SA2jcS+PLs7
iA8NlLYZ04m1xL480dpNPkOWbA==
=wGOB
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
One patch to enable USB Ethernet gadget at Tegra platforms
Commit ff3f0789b3 ("usb: dwc3: use BIT() macro where possible")
changed DWC3_DEPCFG_STREAM_EVENT_EN from bit 13 to bit 12.
Spotted this cleanup typo while looking at diffs between 4.9.35 and
4.14.16 for a separate issue.
Fixes: ff3f0789b3 ("usb: dwc3: use BIT() macro where possible")
Signed-off-by: Erich E. Hoover <ehoover@sweptlaser.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we power off the SoC logic rail in S3, we can find that the Type-C
PHY can't initialize correctly after system resume. We need to toggle
the USB3-OTG reset before trying to initialize the PHY, or else it
times out.
phy phy-ff800000.phy.9: phy poweron failed --> -110
dwc3 fe900000.dwc3: failed to initialize core
dwc3: probe of fe900000.dwc3 failed with error -110
Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. We're still skeptical about that, and we haven't yet found a
case where this seems to have mattered. This approach is much easier, it
simply holds the USB3-OTG reset while device is supended.
The dwc3 core is going to reinitialize the controller at suspend/resume
anyway (including a "soft reset"), so it should be safe to do this.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The kref used to be needed because sharing of fsg_common among multiple USB
function instances was handled by fsg. Now this is managed by configfs, we
don't need it anymore. So let's eliminate kref from this driver.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
fsg_common_set_num_buffers() may fail due to ENOMEM. So add
error handling for fail case.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Even though we only use them once, it is better to not put/release
the GPIOs immediately after use, so that others cannot claim them.
Use devm functions to get the phy GPIOs, so that they will be
automatically released when were unbound from the device and
remove the gpio_put calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
On some Bay Trail (BYT) systems the firmware does not enable the
ULPI Refclk.
This commit adds a helper which checks and if necessary enabled the Refclk
and calls this helper for BYT machines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Bay Trail / BYT SoCs do not have a builtin device-mode phy, instead
they require an external ULPI phy for device-mode.
Only some BYT devices have an external phy, but even on those devices
device-mode is not working because the dwc3 does not see the phy.
The problem is that the ACPI fwnode for the dwc3 does not contain the
expected GPIO resources for the GPIOs connected to the chip-select and
reset pins of the phy.
I've found the workaround which some Android x86 kernels use for this:
https://github.com/BORETS24/Kernel-for-Asus-Zenfone-2/blob/master/arch/x86/platform/intel-mid/device_libs/pci/platform_usb_otg.c
Which boils down to hardcoding the GPIOs for these devices.
The good news it that all boards (*) use the same GPIOs.
This commit fixes the ULPI phy not woring by adding a gpiod_lookup_table
call which adds a hardcoded mapping for BYT devices. Note that the mapping
added by gpiod_add_lookup_table is a fallback mapping, so boards which
properly provide GPIO resources in the ACPI firmware-node resources
will not use this.
*) Except for the first revision of the evalulation-kit, which normal users
don't have
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This documentation patch specifies that certain USB gadget endpoint
operations may be called in interrupt context:
usb_ep_queue, usb_ep_dequeue, usb_ep_set_halt,
usb_ep_clear_halt, usb_ep_set_wedge, usb_ep_fifo_status,
and usb_ep_fifo_flush;
while others must be called in process context:
usb_ep_enable and usb_ep_disable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This fixes the following checkpatch error:
ERROR: code indent should use tabs where possible
Here, spaces are replaced by a tab in 2 lines.
Signed-off-by: Parth Y Shah <sparth1292@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This driver is to be used for Synopsys PCIe-base HAPS platform. Move the
the HAPS support from dwc3-pci to this driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.
It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.
This manifests as the following bugs:
Prior to 946ef68ad4 ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.
After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.
Fixes: 946ef68ad4 ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When utilising multiple instantiations of a UVC gadget on a composite
device, there is no clear method to link a particular configuration to
its respective video node.
Provide a means for identifying the correct video node by exposing the
name of the function configuration through sysfs.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The to_f_uvc_opts() function is forward-declared without needing to, as
its definition can simply be moved up in the file. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Moved dwc2_readl/writel functions after hsotg declaration for
adding hsotg structure to dwc2_readl/writel function prototypes.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Trivial fix to spelling mistake in usbg_us_strings array
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The trace module parameter controls output of debugging messages in the
UVC function driver. Move it from the webcam module to the UVC function
module where it belongs. This allows ConfigFS-based UVC gadgets to
control tracing.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In order to speed up compilation, only include the headers that are
strictly required within other headers. To that end, use forward
structure declaration and move #include statements to .c file as
appropriate.
While at it, sort headers alphabetically, and remove unneeded __KERNEL__
guards.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The UVC gadget userspace API (V4L2 events and custom ioctls) is defined
in a header internal to the kernel. Move it to a new public header to
make it accessible to userspace.
The UVC_INTF_CONTROL and UVC_INTF_STREAMING macros are not used, so
remove them in the process.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Exynos5440 (quad-core A15 with GMAC, PCIe, SATA) was targeting
server platforms but it did not make it to the market really. There are
no development boards with it and probably there are no real products
neither. The development for Exynos5440 ended in 2013 and since then
the platform is in maintenance mode.
Removing Exynos5440 makes our life slightly easier: less maintenance,
smaller code, reduced number of quirks, no need to preserve DTB
backward-compatibility.
The Device Tree sources and some of the drivers for Exynos5440 were
already removed. This removes remaining drivers.
-----BEGIN PGP SIGNATURE-----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=3x4x
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-exynos5440-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Exynos5440 drivers removal
The Exynos5440 (quad-core A15 with GMAC, PCIe, SATA) was targeting
server platforms but it did not make it to the market really. There are
no development boards with it and probably there are no real products
neither. The development for Exynos5440 ended in 2013 and since then
the platform is in maintenance mode.
Removing Exynos5440 makes our life slightly easier: less maintenance,
smaller code, reduced number of quirks, no need to preserve DTB
backward-compatibility.
The Device Tree sources and some of the drivers for Exynos5440 were
already removed. This removes remaining drivers.
* tag 'samsung-drivers-exynos5440-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
The Exynos5440 is not actively developed, there are no development
boards available and probably there are no real products with it.
Remove wide-tree support for Exynos5440.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
32 bit applications can only call ioctl functions on 64 bit systems
when the field .compat_ioctl is defined for file operations.
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on USB2.0 Spec Section 11.12.5,
"If a hub has per-port power switching and per-port current limiting,
an over-current on one port may still cause the power on another port
to fall below specific minimums. In this case, the affected port is
placed in the Power-Off state and C_PORT_OVER_CURRENT is set for the
port, but PORT_OVER_CURRENT is not set."
so let's check C_PORT_OVER_CURRENT too for over current condition.
Fixes: 08d1dec6f4 ("usb:hub set hub->change_bits when over-current happens")
Cc: <stable@vger.kernel.org>
Tested-by: Alessandro Antenucci <antenucci@korg.it>
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add USBTMC_IOCTL_CONFIG_TERMCHAR to control TermChar handling
for next read(). Controls field 'TermChar' and Bit 1 of field
'bmTransferAttributes' of REQUEST_DEV_DEP_MSG_IN BULK-OUT header.
Allows enabling/disabling of terminating a read on reception of
term_char individually for each read request.
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add USBTMC_IOCTL_EOM_ENABLE to specify EOM bit for next write()
call. Sets Bit 0 of field 'bmTransferAttributes' of DEV_DEP_MSG_OUT
Bulk-OUT Header.
Allows fine grained control over end of message handling on a
per file descriptor basis.
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add USBTMC488_IOCTL_TRIGGER to send TRIGGER Bulk-OUT header
according to Subclass USB488 Specification
The usbtmc trigger command is equivalent to the IEEE 488 GET (Group
Execute Trigger) action. While the "*TRG" command can be sent as
data to perform the same operation, in some situations an instrument
will be busy and unable to process the data immediately in which
case the USBTMC488_IOCTL_TRIGGER can be used to trigger the
instrument with lower latency.
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Tested-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ioctls USBTMC_IOCTL_GET_TIMEOUT / USBTMC_IOCTL_SET_TIMEOUT to
get/set I/O timeout for specific file handle.
Different operations on an instrument can take different lengths of
time thus it is important to be able to set the timeout slightly
longer than the expected duration of each operation to optimise the
responsiveness of the application. As the instrument may be shared by
multiple applications the timeout should be settable on a per file
descriptor basis.
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- use consistent error value ETIMEOUT instead of ETIME
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add 'struct usbtmc_file_data' for each file handle to cache last
srq_byte (=Status Byte with SRQ) received by usbtmc_interrupt(..)
usbtmc488_ioctl_read_stb returns cached srq_byte when available for
each file handle to avoid race conditions of concurrent applications.
SRQ now sets EPOLLPRI instead of EPOLLIN since EPOLLIN is now reserved
for asynchronous reads
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build errors when built for PPC64:
These variables are only used on PPC32 so they don't need to be
initialized for PPC64.
../drivers/usb/phy/phy-fsl-usb.c: In function 'usb_otg_start':
../drivers/usb/phy/phy-fsl-usb.c:865:3: error: '_fsl_readl' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:865:16: error: '_fsl_readl_be' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:866:3: error: '_fsl_writel' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:866:17: error: '_fsl_writel_be' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:868:16: error: '_fsl_readl_le' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_le;
../drivers/usb/phy/phy-fsl-usb.c:869:17: error: '_fsl_writel_le' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_le;
and the sysfs "show" function return type should be ssize_t, not int:
../drivers/usb/phy/phy-fsl-usb.c:1042:49: error: initialization of 'ssize_t (*)(struct device *, struct device_attribute *, char *)' {aka 'long int (*)(struct device *, struct device_attribute *, char *)'} from incompatible pointer type 'int (*)(struct device *, struct device_attribute *, char *)' [-Werror=incompatible-pointer-types]
static DEVICE_ATTR(fsl_usb2_otg_state, S_IRUGO, show_fsl_usb2_otg_state, NULL);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.19-rc1, including:
- gpio support for CP2102N devices
- improved line-speed handling for cp210x
- conversion to spin_lock_irqsave() in completion handlers
- dropped kl5kusb105 support from the kl5kusb105 driver (sic!)
Included are also various lower-priority fixes and clean ups.
All but the final commit have been in linux-next, and with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=0ukW
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.19-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.19-rc1
Here are the USB-serial updates for 4.19-rc1, including:
- gpio support for CP2102N devices
- improved line-speed handling for cp210x
- conversion to spin_lock_irqsave() in completion handlers
- dropped kl5kusb105 support from the kl5kusb105 driver (sic!)
Included are also various lower-priority fixes and clean ups.
All but the final commit have been in linux-next, and with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds GPIO support for CP2102N devices.
It introduces new generic code to support emulating separate
input and outputs directions even though these devices
only know output modes (open-drain and pushpull). Existing
GPIO support for CP2105 has been migrated over to the new
code structure.
Only limitation is that for the QFN28 variant, only 4 out of
7 GPIOs are supported. This is because the config array
locations of the last 3 pins are not documented, and reverse
engineering revealed offsets that conflicted with other
documented functions. Hence we'll play it safe instead
until somebody clears this up further.
Signed-off-by: Karoly Pados <pados@pados.hu>
[ johan: fix style issues and a couple of minor bugs; use Karoly's
updated commit message ]
Acked-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
If td_list is not empty the cfg_cmd will not be freed,
call xhci_free_command to free it.
Signed-off-by: Zheng Xiaowei <zhengxiaowei@ruijie.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a bug in the sink PDO search code when trying to select
a PPS APDO. The current code actually sets the starting index for
searching to whatever value 'i' is, rather than choosing index 1
to avoid the first PDO (always 5V fixed). As a result, for sources
which support PPS but whose PPS APDO index does not match with the
supporting sink PPS APDO index for the platform, no valid PPS APDO
will be found so this feature will not be permitted.
Sadly in testing, both Source and Sink capabilities matched up and
this was missed. Code is now updated to correctly set the start
index to 1, and testing with additional PPS capable sources show
this to work as expected.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Fixes: 2eadc33f40 ("typec: tcpm: Add core support for sink side PPS")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1b9ba000 ("Allow function drivers to pause control
transfers") states that USB_GADGET_DELAYED_STATUS is only
supported if data phase is 0 bytes.
It seems that when the length is not 0 bytes, there is no
need to explicitly delay the data stage since the transfer
is not completed until the user responds. However, when the
length is 0, there is no data stage and the transfer is
finished once setup() returns, hence there is a need to
explicitly delay completion.
This manifests as the following bugs:
Prior to 946ef68ad4 ('Let setup() return
USB_GADGET_DELAYED_STATUS'), when setup is 0 bytes, ffs
would require user to queue a 0 byte request in order to
clear setup state. However, that 0 byte request was actually
not needed and would hang and cause errors in other setup
requests.
After the above commit, 0 byte setups work since the gadget
now accepts empty queues to ep0 to clear the delay, but all
other setups hang.
Fixes: 946ef68ad4 ("Let setup() return USB_GADGET_DELAYED_STATUS")
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the coherent_dma_mask for the PS3 ehci, ohci, and snd devices.
Silences WARN_ON_ONCE messages emitted by the dma_alloc_attrs() routine.
Reported-by: Fredrik Noring <noring@nocrew.org>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CP2104 and the ECI interface of CP2105 support further baud rates than
the ones specified in AN205 table 1, and we can use the same equations
as for CP2102N to determine and report back the actual baud rates used.
Note that this could eventually be generalised also to CP2108, which
uses a different base clock. There appears to be an error in the CP2108
equations which needs to be confirmed on actual hardware first however
(specifically, the subtraction of one from the divisor appears to be
incorrect as it introduces larger errors).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The CP2102N equations for determining the actual baud rate can be used
also for other device types, so let's factor it out.
Note that this removes the now unused cp210x_is_cp2102n() helper.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
CP2102N devices support a lot more baudrates than earlier chips by
SiLabs. These devices are not constrained anymore by the table in AN205,
and are able to generate almost any baudrate in the supported range
with only minimal errors. This has also been verified with a scope on
a physical device. This patch adds support for all baudrates supported
by the CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu>
[johan: rework on top of an205 and max-speed patches ]
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Newer cp210x devices support higher line speeds than the older ones
which supported a discrete set of speeds up to 921.6 kbaud.
To support these higher speeds, we have for some time mapped speeds
lower than 1 Mbaud to the speeds supported by older devices, while
allowing the device to pick the closest possible rate for higher speeds
(without trying to guess and report back what rate was actually chosen).
As this implementation can lead to undefined behaviour for older devices
which do not support the higher rates, let's use the later-added
device-type detection to determine the maximum supported speed.
This will also be useful when adding support for cp2102n which can
handle rates up to 3 Mbaud.
As per the data sheets the following maximum speeds are used
cp2101 921.6 kbaud
cp2102/3 1 Mbaud
cp2104/8 2 Mbaud
cp2105
- ECI port 2 Mbaud
- SCI port 921.6 kbaud
while keeping the maximum 2 Mbaud for unknown device types in order to
avoid any regressions.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Older cp210x devices only support a fixed set of line speeds to which a
requested speed is mapped. Reimplement this mapping using a table
instead of a long if-else construct.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The list [1] of commits doing endianness fixes in USB subsystem is long
due to below quote from USB spec Revision 2.0 from April 27, 2000:
------------
8.1 Byte/Bit Ordering
Multiple byte fields in standard descriptors, requests, and responses
are interpreted as and moved over the bus in little-endian order, i.e.
LSB to MSB.
------------
This commit belongs to the same family.
[1] Example of endianness fixes in USB subsystem:
commit 14e1d56cbe ("usb: gadget: f_uac2: endianness fixes.")
commit 42370b8211 ("usb: gadget: f_uac1: endianness fixes.")
commit 63afd5cc78 ("USB: chaoskey: fix Alea quirk on big-endian hosts")
commit 74098c4ac7 ("usb: gadget: acm: fix endianness in notifications")
commit cdd7928df0 ("ACM gadget: fix endianness in notifications")
commit 323ece54e0 ("cdc-wdm: fix endianness bug in debug statements")
commit e102609f10 ("usb: gadget: uvc: Fix endianness mismatches")
list goes on
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make sure only to copy any actual data rather than the whole buffer,
when releasing the temporary buffer used for unaligned non-isochronous
transfers.
Taken directly from commit 0efd937e27 ("USB: ehci-tegra: fix inefficient
copy of unaligned buffers")
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM)
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more
supported way") introduced a common way to align DMA allocations.
The code in the commit aligns the struct dma_aligned_buffer but the
actual DMA address pointed by data[0] gets aligned to an offset from
the allocated boundary by the kmalloc_ptr and the old_xfer_buffer
pointers.
This is against the recommendation in Documentation/DMA-API.txt which
states:
Therefore, it is recommended that driver writers who don't take
special care to determine the cache line size at run time only map
virtual regions that begin and end on page boundaries (which are
guaranteed also to be cache line boundaries).
The effect of this is that architectures with non-coherent DMA caches
may run into memory corruption or kernel crashes with Unhandled
kernel unaligned accesses exceptions.
Fix the alignment by positioning the DMA area in front of the allocation
and use memory at the end of the area for storing the orginal
transfer_buffer pointer. This may have the added benefit of increased
performance as the DMA area is now fully aligned on all architectures.
Tested with Lantiq xRX200 (MIPS) and RPi Model B Rev 2 (ARM).
Fixes: 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in a more supported way")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Aspeed SoC has a memory ordering issue that (thankfully)
only affects the USB gadget device. A read back is necessary
after writing to memory and before letting the device DMA
from it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Variable maxpacket is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'maxpacket' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For unidirectional endpoints, the endpoint pointer will be NULL for the
unused direction. Check that the endpoint is active before
dereferencing this pointer.
Fixes: 1b4977c793 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_in() function")
Fixes: 689efb2619 ("usb: dwc2: Update dwc2_handle_incomplete_isoc_out() function")
Fixes: d84845522d ("usb: dwc2: Update GINTSTS_GOUTNAKEFF interrupt handling")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix build errors when built for PPC64:
These variables are only used on PPC32 so they don't need to be
initialized for PPC64.
../drivers/usb/phy/phy-fsl-usb.c: In function 'usb_otg_start':
../drivers/usb/phy/phy-fsl-usb.c:865:3: error: '_fsl_readl' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:865:16: error: '_fsl_readl_be' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_be;
../drivers/usb/phy/phy-fsl-usb.c:866:3: error: '_fsl_writel' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:866:17: error: '_fsl_writel_be' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_be;
../drivers/usb/phy/phy-fsl-usb.c:868:16: error: '_fsl_readl_le' undeclared (first use in this function); did you mean 'fsl_readl'?
_fsl_readl = _fsl_readl_le;
../drivers/usb/phy/phy-fsl-usb.c:869:17: error: '_fsl_writel_le' undeclared (first use in this function); did you mean 'fsl_writel'?
_fsl_writel = _fsl_writel_le;
and the sysfs "show" function return type should be ssize_t, not int:
../drivers/usb/phy/phy-fsl-usb.c:1042:49: error: initialization of 'ssize_t (*)(struct device *, struct device_attribute *, char *)' {aka 'long int (*)(struct device *, struct device_attribute *, char *)'} from incompatible pointer type 'int (*)(struct device *, struct device_attribute *, char *)' [-Werror=incompatible-pointer-types]
static DEVICE_ATTR(fsl_usb2_otg_state, S_IRUGO, show_fsl_usb2_otg_state, NULL);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When handling split transactions we will try to delay retry after
getting a NAK from the device. This works well for BULK transfers that
can be polled for essentially forever. Unfortunately, on slower systems
at boot time, when the kernel is busy enumerating all the devices (USB
or not), we issue a bunch of control requests (reading device
descriptors, etc). If we get a NAK for the IN part of the control
request and delay retry for too long (because the system is busy), we
may confuse the device when we finally get to reissue SSPLIT/CSPLIT IN
and the device will respond with STALL. As a result we end up with
failure to get device descriptor and will fail to enumerate the device:
[ 3.428801] usb 2-1.2.1: new full-speed USB device number 9 using dwc2
[ 3.508576] usb 2-1.2.1: device descriptor read/8, error -32
[ 3.699150] usb 2-1.2.1: device descriptor read/8, error -32
[ 3.891653] usb 2-1.2.1: new full-speed USB device number 10 using dwc2
[ 3.968859] usb 2-1.2.1: device descriptor read/8, error -32
...
Let's not delay retries of split CONTROL IN transfers, as this allows us
to reliably enumerate devices at boot time.
Fixes: 38d2b5fb75 ("usb: dwc2: host: Don't retry NAKed transactions right away")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Substream period size potentially can be changed in runtime, however
this is not accounted in the data copying routine, the change replaces
the cached value with an actual value from substream runtime.
As a side effect the change also removes a potential division by zero
in u_audio_iso_complete() function, if there is a race with
uac_pcm_hw_free(), which sets prm->period_size to 0.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is no necessity to copy PCM stream ring buffer area and size
properties to UAC private data structure, these values can be got
from substream itself.
The change gives more control on substream and avoid stale caching.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In u_audio_iso_complete, the runtime hw_ptr is updated before the
data is actually copied over to/from the buffer/dma area. When
ALSA uses this hw_ptr, the data may not actually be available to
be used. This causes trash/stale audio to play/record. This
patch updates the hw_ptr after the data has been copied to avoid
this.
Fixes: 132fcb4608 ("usb: gadget: Add Audio Class 2.0 Driver")
Signed-off-by: Joshua Frkuska <joshua_frkuska@mentor.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix below smatch (v0.5.0-4443-g69e9094e11c1) warnings:
drivers/usb/gadget/function/u_audio.c:607 g_audio_setup() warn: strcpy() 'pcm_name' of unknown size might be too large for 'pcm->name'
drivers/usb/gadget/function/u_audio.c:614 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->driver'
drivers/usb/gadget/function/u_audio.c:615 g_audio_setup() warn: strcpy() 'card_name' of unknown size might be too large for 'card->shortname'
Below commits performed a similar 's/strcpy/strlcpy/' rework:
* v2.6.31 commit 8372d4980f ("ALSA: ctxfi - Fix PCM device naming")
* v4.14 commit 003d3e70db ("ALSA: ad1848: fix format string overflow warning")
* v4.14 commit 6d8b04de87 ("ALSA: cs423x: fix format string overflow warning")
Fixes: eb9fecb9e6 ("usb: gadget: f_uac2: split out audio core")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver may sleep in an interrupt handler.
The function call path (from bottom to top) in Linux-4.16.7 is:
[FUNC] r8a66597_queue(GFP_KERNEL)
drivers/usb/gadget/udc/r8a66597-udc.c, 1193:
r8a66597_queue in get_status
drivers/usb/gadget/udc/r8a66597-udc.c, 1301:
get_status in setup_packet
drivers/usb/gadget/udc/r8a66597-udc.c, 1381:
setup_packet in irq_control_stage
drivers/usb/gadget/udc/r8a66597-udc.c, 1508:
irq_control_stage in r8a66597_irq (interrupt handler)
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool (DSAC-2) and checked by
my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16.7 are:
[FUNC] msleep
drivers/usb/gadget/udc/r8a66597-udc.c, 839:
msleep in init_controller
drivers/usb/gadget/udc/r8a66597-udc.c, 96:
init_controller in r8a66597_usb_disconnect
drivers/usb/gadget/udc/r8a66597-udc.c, 93:
spin_lock in r8a66597_usb_disconnect
[FUNC] msleep
drivers/usb/gadget/udc/r8a66597-udc.c, 835:
msleep in init_controller
drivers/usb/gadget/udc/r8a66597-udc.c, 96:
init_controller in r8a66597_usb_disconnect
drivers/usb/gadget/udc/r8a66597-udc.c, 93:
spin_lock in r8a66597_usb_disconnect
To fix these bugs, msleep() is replaced with mdelay().
This bug is found by my static analysis tool (DSAC-2) and checked by
my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current code is broken as it re-defines "req" inside the
if block, then goto out of it. Thus the request that ends
up being sent is not the one that was populated by the
code in question.
This fixes RNDIS driver autodetect by Windows 10 for me.
The bug was introduced by Chris rework to remove the local
queuing inside the if { } block of the redefined request.
Fixes: 636ba13aec ("usb: gadget: composite: remove duplicated code in OS desc handling")
Cc: <stable@vger.kernel.org> # v4.17
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A couple of bugs in the driver are preventing SETUP packets
with an OUT data phase from working properly.
Interestingly those are incredibly rare (RNDIS typically
uses them and thus is broken without this fix).
The main problem was an incorrect register offset being
applied for arming RX on EP0. The other problem relates
to stalling such a packet before the data phase, in which
case we don't get an ACK cycle, and get the next SETUP
packet directly, so we shouldn't reject it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Drop redundant input-speed re-encoding at every open(). The output and
input speeds are initialised to the same value and are kept in sync on
termios updates.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Variables iflag, mask and serial are being assigned but are never used
hence are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'iflag' set but not used [-Wunused-but-set-variable]
warning: variable 'mask' set but not used [-Wunused-but-set-variable]
warning: variable 'serial' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The device (a POS terminal) implements CDC ACM, but has not union
descriptor.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJbRA8GExxwZXRlci5jaGVuQG54cC5jb20ACgkQSFkpgVDWcbsE
Ygf/QAv1RHor7dx2XO0p2lfVSscQegsoXFobtRhItfmwbS1i/P5iavfMqIxRosBh
xac2hHwGSn3isAMRfak3oyKbyrVKo0MYnHHKiQAc1U6X//DQCYfZ933H5wEzXj8q
KvPPPmMLrD5EAgkNcNruYMx0/Onwch/azR+njozVGFpZWfRkAURePGeb0dCTZl/f
/+1Sa3J28No62cUpKrqs55/POjaHSibY8D9iwlQxImkeaBtJNTohevkEUfJunbJ3
0VVWgfEh4BpuInVv6Wu7UzjggRPUrfhozny6qxfHfNpc/RLkZtzcDLD5IsOy3vHc
8cRtU/AamMX3J/tOiAC1tSOSaQ==
=hohq
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One regression fix causes imx51 board hang when using ULPI PHY
Variable maxpacket is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'maxpacket' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer dev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable num_ports is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'num_ports' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable t is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 't' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer dbc is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
variable 'dbc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'selector' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'selector' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable modey is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'modey' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer usbdev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'usbdev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer ep is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'ep' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver was apparently never tested with an actual KLSI device. In
fact, even the device-id entry which was supposed to allow for this had
a typo in it.
Tests now reveal that the predicted firmware differences with the
PalmConnect adapters are real and that the driver does not support KLSI
devices with PID 0x000c, so let's remove the broken entry.
Reported-by: Chris Jakob <chris.jakob@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In general, accessing userspace memory beyond the length of the supplied
buffer in VFS read/write handlers can lead to both kernel memory corruption
(via kernel_read()/kernel_write(), which can e.g. be triggered via
sys_splice()) and privilege escalation inside userspace.
Fix it by using simple_read_from_buffer() instead of custom logic.
Fixes: 6bc235a2e2 ("USB: add driver for Meywa-Denki & Kayac YUREX")
Signed-off-by: Jann Horn <jannh@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a condition check about the PLL acvice of this
controller. Otherwise, the controller might cause hang when
any USB clocks are not supplied yet and accesses the xHCI registers.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch simplifies getting the firmware name for R-Car Gen3.
Almost all R-Car Gen3 USB3.0 Host controllers use "V3". But,
r8a7795 ES1.x SoCs only should use "V2". Since the xhci-plat already
has the firmware_name of R-Car Gen3 as "V3", the xhci-rcar doesn't
need some members of rcar_quirks_match.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To clean up the xhci-rcar.c code later, this patch adds firmware_name
"V3" for R-Car Gen3.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-8 points out that the fix-byte buffer might be too small if
desc->mode is a three-digit number:
drivers/usb/typec/class.c: In function 'typec_register_altmode':
drivers/usb/typec/class.c:502:32: error: '%d' directive writing between 1 and 3 bytes into a region of size 2 [-Werror=format-overflow=]
sprintf(alt->group_name, "mode%d", desc->mode);
^~
drivers/usb/typec/class.c:502:27: note: directive argument in the range [0, 255]
sprintf(alt->group_name, "mode%d", desc->mode);
^~~~~~~~
drivers/usb/typec/class.c:502:2: note: 'sprintf' output between 6 and 8 bytes into a destination of size 6
sprintf(alt->group_name, "mode%d", desc->mode);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
I assume this cannot happen in practice, but we can simply make the
string long enough to avoid the warning. This uses the two padding
bytes that already exist after the string.
Fixes: 4ab8c18d4d ("usb: typec: Register a device for every mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the error handling paths forgets to unlock dp->lock on the error
exit path leading to a potential lock-up. Also the return path for a
successful call to the function configuration_store can return an
uninitialized error return code if dp->alt->active is false, so ensure
ret is zeroed on the successful exit path to avoid garbage being returned.
Detected by CoverityScan, CID#1471597 ("Unitialized scalar variable")
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer adev is being dereferenced before it is being sanity
checked with a null pointer check, hence it is possible for
a null pointer dereference to occur. Fix this by dereferencing
adev only once it is null checked.
Detected by CoverityScan, CID#1471598 ("Dereference before null check")
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corsair Strafe appears to suffer from the same issues
as the Corsair Strafe RGB.
Apply the same quirks (control message delay and init delay)
that the RGB version has to 1b1c:1b15.
With these quirks in place the keyboard works correctly upon
booting the system, and no longer requires reattaching the device.
Signed-off-by: Nico Sneck <snecknico@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The > should be >= here so that we don't read one element beyond the end
of the ep->stream_info->stream_rings[] array.
Fixes: e9df17eb14 ("USB: xhci: Correct assumptions about number of rings per endpoint.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without that option, we run into a link failure:
drivers/usb/gadget/udc/aspeed-vhub/hub.o: In function `ast_vhub_std_hub_request':
hub.c:(.text+0x5b0): undefined reference to `usb_gadget_get_string'
Fixes: 7ecca2a408 ("usb/gadget: Add driver for Aspeed SoC virtual hub")
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are three fixes for broken control-transfer error handling, which
could lead to uninitialised slab data leaking to user space.
Included is also a new device id for cp210x.
All but the final two patches have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=UDQ5
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.18-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
USB-serial fixes for v4.18-rc4
Here are three fixes for broken control-transfer error handling, which
could lead to uninitialised slab data leaking to user space.
Included is also a new device id for cp210x.
All but the final two patches have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing version-request error handling and suppress printing of the
(zeroed) transfer-buffer content in case of errors.
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to return -EIO in case of a short modem-status read request.
While at it, split the debug message to not include the (zeroed)
transfer-buffer content in case of errors.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing transfer-length sanity check to the status-register
completion handler to avoid leaking bits of uninitialised slab data to
user space.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix broken modem-status error handling which could lead to bits of slab
data leaking to user space.
Fixes: 3b36a8fd67 ("usb: fix uninitialized variable warning in keyspan_pda")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
The led trigger core learned a few things that allow to simplify the
trigger drivers. Make use of automated trigger attributes and error
checking of the activate callback. Also use the wrappers to set and get
trigger_data.
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Given that activating a trigger can fail, let the callback return an
indication. This prevents to have a trigger active according to the
"trigger" sysfs attribute but not functional.
All users are changed accordingly to return 0 for now. There is no intended
change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Commit 03e6275ae3 ("usb: chipidea: Fix ULPI on imx51") causes a kernel
hang on imx51 systems that use the ULPI interface and do not select the
CONFIG_USB_CHIPIDEA_ULPI option.
In order to avoid such potential misuse, let's always build the
chipidea ULPI code into the final ci_hdrc object.
Tested on a imx51-babbage board.
Fixes: 03e6275ae3 ("usb: chipidea: Fix ULPI on imx51")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
There are two versions of the Qivicon Zigbee stick in circulation. This
adds the second USB ID to the cp210x driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The "r" variable is an int and "bufsize" is an unsigned int so the
comparison is type promoted to unsigned. If usb_control_msg() returns a
negative that is treated as a high positive value and the error handling
doesn't work.
Fixes: 2d5a9c72d0 ("USB: serial: ch341: fix control-message error handling")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since most target drivers do not use the second fabric_make_tpg() argument
("group") and since it is trivial to derive the group pointer from the wwn
pointer, do not pass the group pointer to fabric_make_tpg().
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The set_current_limit tcpm_dev callback is optional and the tcpm core
will already log the passed in values, so there is no need to have an
empty implementation of this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Comparing an int to a size, which is unsigned, causes the int to become
unsigned, giving the wrong result. usb_get_descriptor can return a
negative error code.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
int x;
expression e,e1;
identifier f;
@@
*x = f(...);
... when != x = e1
when != if (x < 0 || ...) { ... return ...; }
*x < sizeof(e)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds more complete handling of VDMs and registration of
partner alternate modes, and introduces callbacks for
alternate mode operations.
Only DFP role is supported for now.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of the tcpm specific mux states, using the generic
USB Type-C connector state values, and with DisplayPort
using connector states defined for the DisplayPort Alt Mode.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DisplayPort USB Type-C Alt Mode allows DisplayPort displays
and adapters to be attached to the USB Type-C ports on the
system.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing a simple bus for the alternate modes. Bus allows
binding drivers to the discovered alternate modes the
partners support.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before a device was created for every discovered SVID, but
this will create a device for every discovered mode of every
SVID. The idea is to make it easier to create mode specific
drivers once a bus for the alternate mode is added.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for the muxes to be usable with alternate modes,
the alternate mode devices will need also to be able to get
a handle to the muxes on top of the port devices. To make
that possible, the muxes need to be possible to request with
an identifier.
This will change the API so that the mux identifier is given
as a function parameter to typec_mux_get(), and the hard-coded
"typec-mux" is replaced with that value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f2a8aa053c ("typec: tcpm: Represent source supply through
power_supply") moved the code to register a power_supply representing
the device supplying power to the type-C connector, from the fusb302
code to the generic tcpm code so that we have a psy reporting the
supply voltage and current for all tcpm devices.
This broke the reporting of current and voltage through the psy interface
when supplied by a a non pd supply (5V, current as reported by
get_current_limit). The cause of this breakage is port->supply_voltage
and port->current_limit not being set in that case.
This commit fixes this by setting port->supply_voltage and
port->current_limit from tcpm_set_current_limit().
This commit also removes setting supply_voltage and current_limit
from tcpm_reset_port() as that calls tcpm_set_current_limit(0, 0)
which now already sets these to 0.
Fixes: f2a8aa053c ("typec: tcpm: Represent source supply through...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_put_sync() gets called everytime in xhci_dbc_stop().
If dbc is not started, this makes the runtime PM counter incorrectly
becomes 0, and calls autosuspend function. Then we'll keep seeing this:
[54664.762220] xhci_hcd 0000:00:14.0: Root hub is not suspended
So only calls pm_runtime_put_sync() when dbc was started.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds function typec_get_orientation() that can be used
for checking the current cable plug orientation.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move TCPCI(Typec port controller interface) driver and rt1711h
driver out of staging.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As DRP port autonomously toggles the Rp/Rd need a start value to
begin with, so add one parameter for it in tcpm_start_drp_toggling.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support of get typec and power delivery config from
firmware description.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds 3 APIs to get the typec port power and data type,
and preferred power role by its name string.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add fwnode handle to get the fwnode so we can get typec configs
it contains.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the quest to remove all stack VLA usage from the kernel[1], this
uses the maximum buffer size and adds a sanity check. While 25 bytes
is the size of the largest current things coming through, Heikki
Krogerus pointed out that the actual max in 64 bytes, as per ch 1.3.2
http://www.ti.com/lit/ug/slvuan1a/slvuan1a.pdf
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Oliver Neukum <oneukum@suse.com>
Cc: "Bjørn Mork" <bjorn@mork.no>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the code path
__usb_hcd_giveback_urb()
-> wdm_in_callback()
-> service_outstanding_interrupt()
The function service_outstanding_interrupt() will unconditionally enable
interrupts during unlock and invoke usb_submit_urb() with GFP_KERNEL.
If the HCD completes in BH (like ehci does) then the context remains
atomic due local_bh_disable() and enabling interrupts does not change
this.
Defer the error case handling to a workqueue as suggested by Oliver
Neukum. In case of an error the worker performs the read out and wakes
the user.
Fixes: c1da59dad0 ("cdc-wdm: Clear read pipeline in case of error")
Cc: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Cc: legousb-devel@lists.sourceforge.net
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intr_idx_lock lock is acquired only in the completion callback of
the ->int_in_urb (iowarrior_callback()). There is only one URB that is
scheduled / completed so there can't be more than one user of the lock.
The comment says that it protects ->intr_idx and the callback is the
only place in driver that writes to it.
Remove the intr_idx_lock lock because it is superfluous.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wa_urb_dequeue() locks multiple spinlocks while disabling interrupts:
spin_lock_irqsave(&lock1, flags);
spin_lock_irqsave(&lock2, flags2);
Obviously there is no need for the second irqsave and "flags2" variable
since interrupts are disabled at that point. Remove the second irqsave:
spin_lock_irqsave(&lock1, flags);
spin_lock(&lock2);
and eliminate the flags2 variable.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We accidentally return 1 instead of negative error codes.
Fixes: df44831ee2 ("USB host: Add USB ehci support for nuvoton npcm7xx platform")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Avi Fishman <AviFishman70@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are bunch of new device ids for cp210x.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=+oP9
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.18-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.18-rc3
Here are bunch of new device ids for cp210x.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a "tty_" prefix to the tty "flag" variable to avoid any future
mixups with the recently added irq-mask "flags" one.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The portdata spinlock can be taken in interrupt context (via
sierra_outdat_callback()).
Disable interrupts when taking the portdata spinlock when discarding
deferred URBs during close to prevent a possible deadlock.
Fixes: 014333f77c ("USB: sierra: fix urb and memory leak on disconnect")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[ johan: amend commit message and add fixes and stable tags ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
USB Ethernet gadget now works on Tegra114 and Tegra124.
Similar to commit 061e20e989 ("usb: chipidea: tegra: Use aligned DMA
on Tegra30").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The commit 4e88d4c083 ("usb: add a flag to skip PHY
initialization to struct usb_hcd") delete the assignment
for hcd->usb_phy, it causes usb_phy_notify_connect{disconnect)
are not called, the USB PHY driver is not notified of hot plug
event, then the disconnection will not be detected by hardware.
Fixes: 4e88d4c083 ("usb: add a flag to skip PHY initialization
to struct usb_hcd")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reported-by: Mats Karrman <mats.dev.list@gmail.com>
Tested-by: Mats Karrman <mats.dev.list@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch adds support for ehci controller for the Nuvoton
npcm7xx platform.
Most of the code was taken from ehci-spear.c + specific initialization
code
Signed-off-by: Avi Fishman <AviFishman70@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cdc-acm driver does not have a refcount of itself, but uses a
tty_port's refcount. That is, if the refcount of tty_port is '0', we
can clean up the cdc-acm driver by calling the .destruct()
callback function of struct tty_port_operations.
The problem is the destruct() callback function is not called if
the probe() fails, because tty_port's refcount is not zero. So,
add tty_port_put() when probe() fails.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two do the same thing, but we want to remove getnstimeofday64()
to have a more consistent interface.
It would be nice to use a monotonic clocksource here rather than
'real' time, but that would break the user interface.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the new get_resuming_ports HCD method to
the xhci-hcd driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for the new get_resuming_ports HCD method to
the ehci-hcd driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device attached to a root-hub port sends a wakeup request
to a sleeping system, we do not report the wakeup event to the PM
core. This is because a system resume involves waking up all
suspended USB ports as quickly as possible; without the normal
USB_RESUME_TIMEOUT delay, the host controller driver doesn't set the
USB_PORT_STAT_C_SUSPEND flag and so usb_port_resume() doesn't realize
that a wakeup request was received.
However, some environments (such as Chrome OS) want to have all wakeup
events reported so they can be ascribed to the appropriate device. To
accommodate these environments, this patch adds a new routine to the
hub driver and a corresponding new HCD method to be used when a root
hub resumes. The HCD method returns a bitmap of ports that have
initiated a wakeup signal but not yet completed resuming. The hub
driver can then report to the PM core that the child devices attached
to these ports initiated a wakeup event.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port->logbuffer_head may be wrong if the two processes enters
_tcpm_log at the mostly same time. The 2nd process enters _tcpm_log
before the 1st process update the index, then the 2nd process will
not allocate logbuffer, when the 2nd process tries to use log buffer,
the index has already updated by the 1st process, so it will get
NULL pointer for updated logbuffer, the error message like below:
tcpci 0-0050: Log buffer index 6 is NULL
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tcpm_set_state() function take msecs not jiffies.
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to UCSI Specification, Connector Change Event only
means a change in the Connector Status and Operation Mode
fields of the STATUS data structure. So any other change
should create another event.
Unfortunately on some platforms the firmware acting as PPM
(platform policy manager - usually embedded controller
firmware) still does not report any other status changes if
there is a connector change event. So if the connector power
or data role was changed when a device was plugged to the
connector, the driver does not get any indication about
that. The port will show wrong roles if that happens.
To fix the issue, always checking the data and power role
together with a connector change event.
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue where the driver fails with an error:
ioremap error for 0x3f799000-0x3f79a000, requested 0x2, got 0x0
On some platforms the UCSI ACPI mailbox SystemMemory
Operation Region may be setup before the driver has been
loaded. That will lead into the driver failing to map the
mailbox region, as it has been already marked as write-back
memory. acpi_os_ioremap() for x86 uses ioremap_cache()
unconditionally.
When the issue happens, the embedded controller has a
pending query event for the UCSI notification right after
boot-up which causes the operation region to be setup before
UCSI driver has been loaded.
The fix is to notify acpi core that the driver is about to
access memory region which potentially overlaps with an
operation region right before mapping it.
acpi_release_memory() will check if the memory has already
been setup (mapped) by acpi core, and deactivate it (unmap)
if it has. The driver is then able to map the memory with
ioremap_nocache() and set the memtype to uncached for the
region.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Fixes: 8243edf441 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some controllers take almost 55ms to complete controller
restore state (CRS).
There is no timeout limit mentioned in xhci specification so
fixing the issue by increasing the timeout limit to 100ms
[reformat code comment -Mathias]
Signed-off-by: Ajay Gupta <ajaykuee@gmail.com>
Signed-off-by: Nagaraj Annaiah <naga.annaiah@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The address-of operator will always evaluate to true. However,
power should be explicitly disabled if no power domain is used.
Remove the address-of operator.
Fixes: 58c38116c6 ("usb: xhci: tegra: Add support for managing powergates")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initialize the 'err' variate to remove the build warning,
the warning is shown as below:
drivers/usb/host/xhci-tegra.c: In function 'tegra_xusb_mbox_thread':
drivers/usb/host/xhci-tegra.c:552:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
drivers/usb/host/xhci-tegra.c:482:6: note: 'err' was declared here
Fixes: e84fce0f88 ("usb: xhci: Add NVIDIA Tegra XUSB controller driver")
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't rely on event interrupt (EINT) bit alone to detect pending port
change in resume. If no change event is detected the host may be suspended
again, oterwise roothubs are resumed.
There is a lag in xHC setting EINT. If we don't notice the pending change
in resume, and the controller is runtime suspeded again, it causes the
event handler to assume host is dead as it will fail to read xHC registers
once PCI puts the controller to D3 state.
[ 268.520969] xhci_hcd: xhci_resume: starting port polling.
[ 268.520985] xhci_hcd: xhci_hub_status_data: stopping port polling.
[ 268.521030] xhci_hcd: xhci_suspend: stopping port polling.
[ 268.521040] xhci_hcd: // Setting command ring address to 0x349bd001
[ 268.521139] xhci_hcd: Port Status Change Event for port 3
[ 268.521149] xhci_hcd: resume root hub
[ 268.521163] xhci_hcd: port resume event for port 3
[ 268.521168] xhci_hcd: xHC is not running.
[ 268.521174] xhci_hcd: handle_port_status: starting port polling.
[ 268.596322] xhci_hcd: xhci_hc_died: xHCI host controller not responding, assume dead
The EINT lag is described in a additional note in xhci specs 4.19.2:
"Due to internal xHC scheduling and system delays, there will be a lag
between a change bit being set and the Port Status Change Event that it
generated being written to the Event Ring. If SW reads the PORTSC and
sees a change bit set, there is no guarantee that the corresponding Port
Status Change Event has already been written into the Event Ring."
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Negative error code will be larger than sizeof().
Note that none of these bugs prevent errors from being detected, even if
the ir-usb one would cause a less precise debug message to printed.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
[ johan: add comment about implications ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The sbitmap and the percpu_ida perform essentially the same task,
allocating tags for commands. The sbitmap outperforms the percpu_ida as
documented here: https://lkml.org/lkml/2014/4/22/553
The sbitmap interface is a little harder to use, but being able to remove
the percpu_ida code and getting better performance justifies the additional
complexity.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> # f_tcm
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Introduce target_free_tag() and convert all drivers to use it.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PID bitfield in descriptor should be set based on particular request
length, not based on EP's mc value. PID value can't be set to 0 even
request length is 0.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Freed allocated request for ep0 to prevent memory leak in case when
dwc2_driver_probe() failed.
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It happens when enable debug log, if set_alt() returns
USB_GADGET_DELAYED_STATUS and usb_composite_setup_continue()
is called before increasing count of @delayed_status,
so fix it by using spinlock of @cdev->lock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Jay Hsu <shih-chieh.hsu@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If isoc split in transfer with no data (the length of DATA0
packet is zero), we can't simply return immediately. Because
the DATA0 can be the first transaction or the second transaction
for the isoc split in transaction. If the DATA0 packet with no
data is in the first transaction, we can return immediately.
But if the DATA0 packet with no data is in the second transaction
of isoc split in transaction sequence, we need to increase the
qtd->isoc_frame_index and giveback urb to device driver if needed,
otherwise, the MDATA packet will be lost.
A typical test case is that connect the dwc2 controller with an
usb hs Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
In the case, the isoc split in transaction sequence like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet (176 bytes)
- CSPLIT IN transaction
- DATA0 packet (0 byte)
This patch use both the length of DATA0 and qtd->isoc_split_offset
to check if the DATA0 is in the second transaction.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The commit 3bc04e28a0 ("usb: dwc2: host: Get aligned DMA in
a more supported way") rips out a lot of code to simply the
allocation of aligned DMA. However, it also introduces a new
issue when use isoc split in transfer.
In my test case, I connect the dwc2 controller with an usb hs
Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
It's because that the usb Hub uses an MDATA for the first
transaction and a DATA0 for the second transaction for the isoc
split in transaction. An typical isoc split in transaction sequence
like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet
- CSPLIT IN transaction
- DATA0 packet
The DMA address of MDATA (urb->dma) is always DWORD-aligned, but
the DMA address of DATA0 (urb->dma + qtd->isoc_split_offset) may
not be DWORD-aligned, it depends on the qtd->isoc_split_offset (the
length of MDATA). In my test case, the length of MDATA is usually
unaligned, this cause DATA0 packet transmission error.
This patch use kmem_cache to allocate aligned DMA buf for isoc
split in transaction. Note that according to usb 2.0 spec, the
maximum data payload size is 1023 bytes for each fs isoc ep,
and the maximum allowable interrupt data payload size is 64 bytes
or less for fs interrupt ep. So we set the size of object to be
1024 bytes in the kmem cache.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The dwc2_get_ls_map() use ttport to reference into the
bitmap if we're on a multi_tt hub. But the bitmaps index
from 0 to (hub->maxchild - 1), while the ttport index from
1 to hub->maxchild. This will cause invalid memory access
when the number of ttport is hub->maxchild.
Without this patch, I can easily meet a Kernel panic issue
if connect a low-speed USB mouse with the max port of FE2.1
multi-tt hub (1a40:0201) on rk3288 platform.
Fixes: 9f9f09b048 ("usb: dwc2: host: Totally redo the microframe scheduler")
Cc: <stable@vger.kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan hminas@synopsys.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case when a hub is connected to DWC2 host
auto suspend occurs and host goes to
hibernation. When any device connected to hub
host hibernation exiting incorrectly.
- Added dwc2_hcd_rem_wakeup() function call to
exit from suspend state by remote wakeup.
- Increase timeout value for port suspend bit to be set.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The #ifdef guards around these are wrong, resulting in warnings
in certain configurations:
drivers/usb/dwc3/dwc3-qcom.c:244:12: error: 'dwc3_qcom_resume' defined but not used [-Werror=unused-function]
static int dwc3_qcom_resume(struct dwc3_qcom *qcom)
^~~~~~~~~~~~~~~~
drivers/usb/dwc3/dwc3-qcom.c:223:12: error: 'dwc3_qcom_suspend' defined but not used [-Werror=unused-function]
static int dwc3_qcom_suspend(struct dwc3_qcom *qcom)
This replaces the guards with __maybe_unused annotations to shut up
the warnings and give better compile time coverage.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix to return error code -ENODEV from the get device failed error
handling case instead of 0, as done elsewhere in this function.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In ISOC OUT transfer, when the OUT token received while EP disabled,
we shouldn't complete a usb request. The current flow completed one
usb request, this will lead to a packet drop to function driver.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit fe8abf332b ("usb: dwc3: support clocks and resets for DWC3 core")
adds support for handling clocks and resets in the DWC3 core, so that for
platforms following the standard devicetree bindings this does not need
to be duplicated in all the different glue layers.
These changes intended for devicetree based platforms introduce an
uncoditional clk_bulk_get() in the core probe path. This leads to the
following error being logged on x86/ACPI systems:
[ 26.276783] dwc3 dwc3.3.auto: Failed to get clk 'ref': -2
This commits wraps the clk_bulk_get() in an if (dev->of_node) check so
that it only is done on devicetree instantiated devices, fixing this
error.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In ISOC transfer, when the NAK interrupt happens, we shouldn't complete
a usb request, the current flow will complete one usb request with no
hardware transfer, this will lead to a packet drop on the usb bus.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The clocks have already been explicitly disabled and put as part of
remove() so the runtime suspend callback must not be run when balancing
the runtime PM usage count before returning.
Fixes: 16adc674d0 ("usb: dwc3: add generic OF glue layer")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of requests queue is empty reset EP target_frame to
initial value.
This allow restarting ISOC traffic in case when function
driver queued requests with interruptions.
Tested-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Silicon Labs defines alternative VID/PID pairs for some chips that when
used will automatically install drivers for Windows users without manual
intervention. Unfortunately, these IDs are not recognized by the Linux
module, so using these IDs improves user experience on one platform but
degrades it on Linux. This patch addresses this problem.
Signed-off-by: Karoly Pados <pados@pados.hu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is a late set of changes from Deepa Dinamani doing an automated
treewide conversion of the inode and iattr structures from 'timespec'
to 'timespec64', to push the conversion from the VFS layer into the
individual file systems.
There were no conflicts between this and the contents of linux-next
until just before the merge window, when we saw multiple problems:
- A minor conflict with my own y2038 fixes, which I could address
by adding another patch on top here.
- One semantic conflict with late changes to the NFS tree. I addressed
this by merging Deepa's original branch on top of the changes that
now got merged into mainline and making sure the merge commit includes
the necessary changes as produced by coccinelle.
- A trivial conflict against the removal of staging/lustre.
- Multiple conflicts against the VFS changes in the overlayfs tree.
These are still part of linux-next, but apparently this is no longer
intended for 4.18 [1], so I am ignoring that part.
As Deepa writes:
The series aims to switch vfs timestamps to use struct timespec64.
Currently vfs uses struct timespec, which is not y2038 safe.
The series involves the following:
1. Add vfs helper functions for supporting struct timepec64 timestamps.
2. Cast prints of vfs timestamps to avoid warnings after the switch.
3. Simplify code using vfs timestamps so that the actual
replacement becomes easy.
4. Convert vfs timestamps to use struct timespec64 using a script.
This is a flag day patch.
Next steps:
1. Convert APIs that can handle timespec64, instead of converting
timestamps at the boundaries.
2. Update internal data structures to avoid timestamp conversions.
Thomas Gleixner adds:
I think there is no point to drag that out for the next merge window.
The whole thing needs to be done in one go for the core changes which
means that you're going to play that catchup game forever. Let's get
over with it towards the end of the merge window.
[1] https://www.spinics.net/lists/linux-fsdevel/msg128294.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CZX2
-----END PGP SIGNATURE-----
Merge tag 'vfs-timespec64' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground
Pull inode timestamps conversion to timespec64 from Arnd Bergmann:
"This is a late set of changes from Deepa Dinamani doing an automated
treewide conversion of the inode and iattr structures from 'timespec'
to 'timespec64', to push the conversion from the VFS layer into the
individual file systems.
As Deepa writes:
'The series aims to switch vfs timestamps to use struct timespec64.
Currently vfs uses struct timespec, which is not y2038 safe.
The series involves the following:
1. Add vfs helper functions for supporting struct timepec64
timestamps.
2. Cast prints of vfs timestamps to avoid warnings after the switch.
3. Simplify code using vfs timestamps so that the actual replacement
becomes easy.
4. Convert vfs timestamps to use struct timespec64 using a script.
This is a flag day patch.
Next steps:
1. Convert APIs that can handle timespec64, instead of converting
timestamps at the boundaries.
2. Update internal data structures to avoid timestamp conversions'
Thomas Gleixner adds:
'I think there is no point to drag that out for the next merge
window. The whole thing needs to be done in one go for the core
changes which means that you're going to play that catchup game
forever. Let's get over with it towards the end of the merge window'"
* tag 'vfs-timespec64' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground:
pstore: Remove bogus format string definition
vfs: change inode times to use struct timespec64
pstore: Convert internal records to timespec64
udf: Simplify calls to udf_disk_stamp_to_time
fs: nfs: get rid of memcpys for inode times
ceph: make inode time prints to be long long
lustre: Use long long type to print inode time
fs: add timespec64_truncate()
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
Here is the driver core patchset for 4.18-rc1.
The large chunk of these are firmware core documentation and api
updates. Nothing major there, just better descriptions for others to be
able to understand the firmware code better. There's also a user for a
new firmware api call.
Other than that, there are some minor updates for debugfs, kernfs, and
the driver core itself.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbZAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykbiACgu/2qqou1iV4GxOkvrj5wfsHD+lYAoNPNNDHu
Qf3CCEKbxogF6YowDiAH
=Dsqq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the driver core patchset for 4.18-rc1.
The large chunk of these are firmware core documentation and api
updates. Nothing major there, just better descriptions for others to
be able to understand the firmware code better. There's also a user
for a new firmware api call.
Other than that, there are some minor updates for debugfs, kernfs, and
the driver core itself.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
driver core: hold dev's parent lock when needed
driver-core: return EINVAL error instead of BUG_ON()
driver core: add __printf verification to device_create_groups_vargs
mm: memory_hotplug: use put_device() if device_register fail
base: core: fix typo 'can by' to 'can be'
debugfs: inode: debugfs_create_dir uses mode permission from parent
debugfs: Re-use kstrtobool_from_user()
Documentation: clarify firmware_class provenance and why we can't rename the module
Documentation: remove stale firmware API reference
Documentation: fix few typos and clarifications for the firmware loader
ath10k: re-enable the firmware fallback mechanism for testmode
ath10k: use firmware_request_nowarn() to load firmware
firmware: add firmware_request_nowarn() - load firmware without warnings
firmware_loader: make firmware_fallback_sysfs() print more useful
firmware_loader: move kconfig FW_LOADER entries to its own file
firmware_loader: replace ---help--- with help
firmware_loader: enhance Kconfig documentation over FW_LOADER
firmware_loader: document firmware_sysfs_fallback()
firmware: rename fw_sysfs_fallback to firmware_fallback_sysfs()
firmware: use () to terminate kernel-doc function names
...
Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the
staging portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxba6w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykumQCg2abWE5LijR0SNJIwX8xk64HLUAMAnAxBZDG3
aB0GyOQd54L+09q4LAdn
=ZCEx
-----END PGP SIGNATURE-----
Merge tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY updates from Greg KH:
"Here is the big USB pull request for 4.18-rc1.
Lots of stuff here, the highlights are:
- phy driver updates and new additions
- usual set of xhci driver updates
- normal set of musb updates
- gadget driver updates and new controllers
- typec work, it's getting closer to getting fully out of the staging
portion of the tree.
- lots of minor cleanups and bugfixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
Revert "xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"
xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers
xhci: Allow more than 32 quirks
usb: xhci: force all memory allocations to node
selftests: add test for USB over IP driver
USB: typec: fsusb302: no need to check return value of debugfs_create_dir()
USB: gadget: udc: s3c2410_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: renesas_usb3: no need to check return value of debugfs_create functions
USB: gadget: udc: pxa27x_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: gr_udc: no need to check return value of debugfs_create functions
USB: gadget: udc: bcm63xx_udc: no need to check return value of debugfs_create functions
USB: udc: atmel_usba_udc: no need to check return value of debugfs_create functions
USB: dwc3: no need to check return value of debugfs_create functions
USB: dwc2: no need to check return value of debugfs_create functions
USB: core: no need to check return value of debugfs_create functions
USB: chipidea: no need to check return value of debugfs_create functions
USB: ehci-hcd: no need to check return value of debugfs_create functions
USB: fhci-hcd: no need to check return value of debugfs_create functions
USB: fotg210-hcd: no need to check return value of debugfs_create functions
USB: imx21-hcd: no need to check return value of debugfs_create functions
...
This reverts commit 8466489ef5.
Now that we can properly reset the uPD72020x without a hard PCI reset,
let's get rid of the existing quirks.
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Renesas controllers get into a weird state if they are reset while
programmed with 64bit addresses (they will preserve the top half of the
address in internal, non visible registers).
You end up with half the address coming from the kernel, and the other
half coming from the firmware.
Also, changing the programming leads to extra accesses even if the
controller is supposed to be halted. The controller ends up with a fatal
fault, and is then ripe for being properly reset. On the flip side,
this is completely unsafe if the defvice isn't behind an IOMMU, so
we have to make sure that this is the case. Can you say "broken"?
This is an alternative method to the one introduced in 8466489ef5
("xhci: Reset Renesas uPD72020x USB controller for 32-bit DMA issue"),
which will subsequently be removed.
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now have 32 different quirks, and the field that holds them
is full. Let's bump it up to the next stage so that we can handle
some more... The type is now an unsigned long long, which is 64bit
on most architectures.
We take this opportunity to change the quirks from using (1 << x)
to BIT_ULL(x).
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci driver forces DMA memory to be node aware, however, there are
several ring-related memory allocations that are not memory node aware.
This patch resolves those *alloc functions to be allocated on the proper
memory node.
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Clean up the fsusb302 driver to not care if the root directory was
created, as the code should work properly either way.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the device structure.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the device structure.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jaejoong Kim <climbbb.kim@gmail.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the device structure.
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the device structure.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johan Hovold <johan@kernel.org>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the host controller structure.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Johan Hovold <johan@kernel.org>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@intel.com>
Cc: Vasyl Gomonovych <gomonovych@gmail.com>
Cc: Mariusz Skamra <mariuszx.skamra@intel.com>
Cc: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
There is also no need to keep the file dentries around at all, so remove
those variables from the host controller structure.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
We do need to save the dentries for these files, so keep them around,
but no need to check if they are "valid" or not, as the code works just
as well either way.
Cc: Pete Zaitcev <zaitcev@kotori.zaitcev.us>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Fredrik Noring <noring@nocrew.org>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because of this, lots of init functions do not need to have return
values, so this cleans up a lot of unused error handling code that never
could have triggered in the past.
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Clean up the tcpm.c code to not care about this, turns out no one was
even checking the return value of this function, so it didn't matter.
Note, I do not think this code can be removed in a running system, as
the debugfs root directory will stick around, that should be fixed
someday...
Revieved-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A built-in PHY driver cannot link against modular USB core code:
drivers/usb/phy/phy-tegra-usb.o: In function `tegra_usb_phy_probe':
phy-tegra-usb.c:(.text+0x6bc): undefined reference to `usb_get_dr_mode'
This uses a 'select' statement in Kconfig like we have for other such
PHY drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the USB hub core waits for 50 ms after enumerating the
device. This was added to help "some high speed devices" to
enumerate (b789696af8 "[PATCH] USB: relax usbcore reset timings").
On some devices, the time-to-active is important, so we provide
a per-port option to reduce the time to what the USB specification
requires: 10 ms.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "old" enumeration scheme is considerably faster (it takes
~244ms instead of ~356ms to get the descriptor).
It is currently only possible to use the old scheme globally
(/sys/module/usbcore/parameters/old_scheme_first), which is not
desirable as the new scheme was introduced to increase compatibility
with more devices.
However, in our case, we care about time-to-active for a specific
USB device (which we make the firmware for), on a specific port
(that is pogo-pin based: not a standard USB port). This new
sysfs option makes it possible to use the old scheme on a single
port only.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix silly mistake when enabling runtime PM support for the Tegra XHCI
driver. If runtime PM was enabled correctly for the XHCI device, then
we should call pm_runtime_get_sync() to enable the device.
Fixes: ee9e5f4c78 ("usb: xhci: tegra: Add runtime PM support")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Workaround introduced for i.MX53 in be9cae2479 ("usb: chipidea:
imx: Fix ULPI on imx53") seems to be applicable in case of i.MX51 as
well. Running latest kernel on ZII RDU1 Board (imx51-zii-rdu1.dts)
exhibits a kernel frozen on PORTSC access and applying the workaround
resolves the issue.
Fixes: be9cae2479 ("usb: chipidea: imx: Fix ULPI on imx53")
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-By: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the only users of this variable got removed, we now get a
warning about 'otg' being unused:
drivers/usb/musb/da8xx.c: In function 'da8xx_musb_interrupt':
drivers/usb/musb/da8xx.c:226:19: error: unused variable 'otg' [-Werror=unused-variable]
Fixes: d2852f2d3e ("usb: musb: remove references to default_a of struct usb_otg")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears that a "#define DEBUG" was left in on the recent patch
landed for the Qualcomm DWC3 glue driver. Let's remove it.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Host Controller driver 'ohci-at91.c' reads a Special Function
Register - OHCI Interrupt Configuration Register (AT91_SFR_OHCIICR)
for bits SUSPEND_A/B/C. These bits are defined in sama5d2 alone, so
sfr register mapping is done with compatible string "atmel,sama5d2-sfr".
This gives a kernel warning 'failed to find sfr node' with non sama5d2
cpus which is removed here, thus leaving it up to having a proper DTS.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to do extra endianness conversion in
usb_set_isoch_delay because it is already done
in usb_control_msg()
Fixes: 886ee36e72 ("usb: core: add support for USB_REQ_SET_ISOCH_DELAY")
Cc: Dmytro Panchenko <dmytro.panchenko@globallogic.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # v4.16+
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 4.18-rc1, including:
- support for hardware-assisted XON/XOFF output flow control for pl2303
- fix for a long-standing IXON/IXOFF mixup in ftdi_sio
- blacklist of two apparently unused dwm-158 modem interfaces that
confused some user space daemon (option)
- add missing const to a tty helper currently used by USB serial only
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=gsOA
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.18-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.18-rc1
Here are the USB-serial updates for 4.18-rc1, including:
- support for hardware-assisted XON/XOFF output flow control for pl2303
- fix for a long-standing IXON/IXOFF mixup in ftdi_sio
- blacklist of two apparently unused dwm-158 modem interfaces that
confused some user space daemon (option)
- add missing const to a tty helper currently used by USB serial only
Included are also various clean ups.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
SoC have internal I/O buses that can't be proved for devices. The
devices on the buses can be accessed directly without additinal
configuration required. This type of bus is represented as
"simple-bus". In some platforms, we name "soc" with "simple-bus"
attribute and many devices are hooked under it described in DT
(device tree).
In commit bf74ad5bc4 ("Hold the device's parent's lock during
probe and remove") to solve USB subsystem lock sequence since
USB device's characteristic. Thus "soc" needs to be locked
whenever a device and driver's probing happen under "soc" bus.
During this period, an async driver tries to probe a device which
is under the "soc" bus would be blocked until previous driver
finish the probing and release "soc" lock. And the next probing
under the "soc" bus need to wait for async finish. Because of
that, driver's async probe for init time improvement will be
shadowed.
Since many devices don't have USB devices' characteristic, they
actually don't need parent's lock. Thus, we introduce a lock flag
in bus_type struct and driver core would lock the parent lock base
on the flag. For USB, we set this flag in usb_bus_type to keep
original lock behavior in driver core.
Async probe could have more benefit after this patch.
Signed-off-by: Martin Liu <liumartin@google.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra XHCI controller requires that the XUSBA (for superspeed) and
XUSBC (for host) power-domains are enabled. Commit 8df127456f
("soc/tegra: pmc: Enable XUSB partitions on boot") was added to force
on these power-domains if the XHCI driver is enabled while proper
power-domain support is added, to ensure the device did not hang on
boot. However, rather than forcing on these power-domains in the PMC
driver we can use the legacy Tegra powergate APIs to turn on these
power-domains during the probe of the Tegra XHCI driver.
In the near future we plan to move the Tegra XHCI driver to use the
generic PM domain framework for power-domains and so to prepare for
this only use the legacy Tegra powergate API if there is not PM
domain associated with device (ie. dev.pm_domain is NULL). Please
note that in the future the superspeed and host resets will be handled
by the generic PM domain provider and so these are only these are only
needed in the case where there is no generic PM domain.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add runtime PM support to the Tegra XHCI driver and move the function
calls to enable/disable the clocks, regulators and PHY into the runtime
PM callbacks.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding runtime PM support to the Tegra XHCI driver, it is desirable
to move the function calls to enable the clocks, regulators and PHY from
the tegra_xusb_probe into the runtime PM handlers. Currently, the
clocks, regulators and PHY are all enabled before we call
usb_create_hcd() in tegra_xusb_probe(), however, we cannot call
pm_runtime_get_sync() at this point because the platform device data is
not yet initialised. Fortunately, the function usb_create_hcd() can be
called before we enable the clocks, regulators and PHY and so prepare
for adding runtime PM support, by moving the call to usb_create_hcd()
before we enable the hardware.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ALWAYS_SYNC flag is currently honored by the usb-storage driver but not UAS
and is required to work around devices that become unstable upon being
queried for cache. This code is taken straight from:
drivers/usb/storage/scsiglue.c:284
Signed-off-by: Alexander Kappner <agk@godking.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB Type-C PHY in Intel WhiskeyCove PMIC has build-in
USB Type-C state machine which we were relying on to
configure the CC lines correctly. This patch removes that
dependency and configures the CC line according to commands
from the port manager (tcpm.c) in wcove_set_cc().
This fixes an issue where USB devices attached to the USB
Type-C port do not get enumerated. When acting as
source/host, the HW FSM sometimes fails to configure the PHY
correctly.
Fixes: 3c4fb9f169 ("usb: typec: wcove: start using tcpm for USB PD support")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue where the mux does not get configured
when the parent device is suspended. The registers for this
mux are mapped to the parent device MMIO (usually xHCI PCI
device), so in order for the driver to be able to program
the registers, the parent device must be resumed.
Reported-by: Sathyanarayanan Kuppuswamy <sathyanarayanan.kuppuswamy@intel.com>
Fixes: f6fb9ec02b ("usb: roles: Add Intel xHCI USB role switch driver")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing the "fusb302" debugfs directory when unloading
the driver. That allows the driver to be loaded more then
one time. The directory will not get actually removed until
it is empty, so only after the last instance has been
removed.
This fixes an issue where the driver can't be re-loaded if
it has been unloaded as the "fusb302" debugfs directory
already exists.
Fixes: 76f0c53d08 ("usb: typec: fusb302: Move out of staging")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to determine the USB port type with this mux is very
difficult. To simplify the situation, always allow user
control, even if the port is USB Type-C port.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix htmldocs warning:
drivers/usb/typec/mux.c:186: warning: Function parameter or member 'mux' not described in
'typec_mux_unregister'
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: bdecb33af3 ("usb: typec: API for controlling USB Type-C Multiplexers")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pdev_nr and rhport can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/usbip/vhci_sysfs.c:238 detach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:328 attach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:338 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_ss->vdev'
drivers/usb/usbip/vhci_sysfs.c:340 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_hs->vdev'
Fix this by sanitizing pdev_nr and rhport before using them to index
vhcis and vhci->vhci_hcd_ss->vdev respectively.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When printer_write() calls usb_ep_queue(), a udc driver (e.g.
renesas_usbhs driver) may call usb_gadget_giveback_request() in
the udc .queue ops immediately. Then, printer_write() calls
list_add(&req->list, &dev->tx_reqs_active) wrongly. After that,
if we do unbind the printer driver, WARN_ON() happens in
printer_func_unbind() because the list entry is not removed.
So, this patch moves list_add(&req->list, &dev->tx_reqs_active)
calling before usb_ep_queue().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For supply registration, provide fwnode pointer of the port device,
via the power_supply_config structure, to allow other psy drivers
to add us as a supplier. At present this only applies to DT
based platforms using the 'power-supplies' DT property, but in the
future should also work for ACPI platforms when the relevant support
is added to the power_supply core.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The notifier callbacks of extcon are called in atomic context, but the
callbacks will call regulator_enable()/regulator_disable() which may
sleep caused by mutex, so use work queue to call the sleep functions.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When VBUS_FALL interrupt arises, it means U3 device is disconnected
with host, so need reset status of gadget
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear test_mode flag when the gadget is reset by host, otherwise
will affect the next test item.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reset EP when disable it to reset data toggle for U2 EP, and
SeqN, flow control status etc for U3 EP, this can avoid
issue of uncontinuous SeqN
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the controller receives a LPM request, it will reject the LPM
request, and need software to re-enable it after LPM resume if the
controller doesn't remote wakeup from L1 automatically
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable compliance transition for a port by writing "compliance" to the
ports portsc file in debugfs.
port must be "Not-connected" and Link must be in RxDetect state to enable
compliance mode.
Only needed for host that have CTC flag set.
Allows state transitioning to compliance at 1st LFPS timeout.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ports/portxx/portsc for each xHC hardware usb port to debugfs.
Showing the content of the port status and control register for
each port (PORTSC)
Portxx is numbered starting from 1 for historical reasons to better
match port numbering shown by lsusb and other places.
Ports in debugfs are in the order XHC controller has them,
In most cases USB2 ports come first, followed by USB3 ports.
i.e. USB2 ports are port01-portxx, and USB3 portxx-portmax.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we are now using the new port strtuctes the port_arrays
are no longer needed, remove them completely
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_get_ports() is one of the last functions using port_arrays in
xhci-hub.c. We get the same data directly from hub and port structures
instead, so convert and remove both xhci_get_ports() and port_arrays from
all function that no longer need it.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get rid of port iomem arrays and use port structures in the following
functions:
xhci_find_raw_port_number()
xhci_disable_port_wake_on_bits()
xhci_set_usb2_hardware_lpm()
xhci_all_ports_seen_u0()
compliance_mode_recovery()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't use pointers to port array and port index as function parameters
in xhci_test_and_clear_bit(), just use a pointer to the right port
structure.
xhci_test_and_clear_bit() was the last port_array user in
xhci_get_port_status() and handle_port_status(), so remove the
port_array from them as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove old iomem port array and index as parameters, just
send a ponter to a port strucure instread
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hcd_portnum is a better desctiption than faked_port_index, and
is in line with the name the port structure uses.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use port structures in the port event handler.
Getting the right hcd and hcd portnumber from the hardware port number
is a lot easier with port structures, and allows us to remove a lot
of the previous code, including the find_faked_portnum_from_hw_index()
function
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use port structures instead of mmio port arrays for
xhci_port_missing_cas_quirk() and xhci_set_remote_wake_mask() in
xhci-hub.c
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new port structures for functions in xhci-hub.c to get
port mmio address of portsc register instead of the port array
xhci_get_port_io_addr() is no longer needeed and is removed.
Plan is to get rid of the mmio port array completely.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
quick way to get the xhci roothub and thus all the ports
belonging to a certain hcd
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows us to know the correct hcd a xhci roothub and its ports
belong to.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current way of having one array telling only the port speed,
and then two separate arrays with mmio addresses for usb2 and usb3 ports
requeres helper functions to transate hw to hcd, and hcd to hw port
numbers, and is hard to expand.
Instead create a structure describing a port, including the mmio address,
the port hardware index, hcd port index, and a pointer to the roothub
it belongs to.
Create one array containing all port structures in the same order the
hardware controller sees them. Then add an array of port pointers to
each xhci hub structure pointing to the ports that belonging to the
roothub.
This way we can easily convert hw indexed port events to usb core
hcd port numbers, and vice versa usb core hub hcd port numbers
to hw index and mmio address.
Other benefit is that we can easily find the parent hcd and xhci
structure of a port structure. This is useful in debugfs where
we can give one port structure pointer as parameter and get both
the correct mmio address and xhci lock needed to set some port
parameter.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds support for HiSilicon STB xHCI host controller.
There are two xHCI host controllers on HiSilicon STB SoCs. Each
one requires additional configuration before exposing interface
compliant with xHCI.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A total of 98 non-merge commits, the biggest part being in dwc3 this
time around with a large refactoring of dwc3's transfer handling code.
We also have a new driver for Aspeed virtual hub controller.
Apart from that, just a list of miscellaneous fixes all over the place.
-----BEGIN PGP SIGNATURE-----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=b56m
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
usb: changes for v4.18 merge window
A total of 98 non-merge commits, the biggest part being in dwc3 this
time around with a large refactoring of dwc3's transfer handling code.
We also have a new driver for Aspeed virtual hub controller.
Apart from that, just a list of miscellaneous fixes all over the place.
UDC core ensures the usb_ep parameter passed in is not NULL, so
checking if (ep != NULL) is pointless.
Convert to_musb_ep() to a simple macro to not directly return NULL to
avoid warnings from code static analysis tools.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget function drivers should ensure the usb_request parameter
passed in is not NULL. UDC core doesn't check if it is NULL, so MUSB
driver shouldn't have to check it either.
Convert to_musb_request() to a simple macro to not directly return NULL
to avoid warnings from code static analysis tools.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to use DSPS-based controllers with device-tree descriptions
of the USB topology, we need to associate the glue device's device-tree
node with the child controller device.
Note that this can also be used to eventually let USB core manage
generic phys.
Also note that the other glue drivers will require similar changes to be
able to describe their buses in DT.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As decided in the discussion [1] we are deleting the otg protocol
support from the musb drivers.
First this patch disables the flags for enabling the otg protocols. We
will later gradually delete the otg protocol code from the musb drivers.
[1] https://www.spinics.net/lists/linux-usb/msg167003.html
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb drivers do not use the otg fsm framework, so referencing to
otg->default_a doesn't have any effect, so remove the references.
But tusb6010 glue driver uses it locally to control the vbus power, so
keep the references in tusb6010 only.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_stage0_irq() is 400+ lines long. Break its interrupt events
handling into each individual functions to make it easy to read.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following members in struct musb_hdrc_config are not used,
so remove them.
soft_con
utm_16
big_endian
mult_bulk_tx
mult_bulk_rx
high_iso_tx
high_iso_rx
dma
dma_channels
dyn_fifo_size
vendor_ctrl
vendor_stat
vendor_req
dma_req_chan
musb_hdrc_eps_bits
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/linux/usb/musb.h already defines enum for musb port mode, so
remove the duplicate in musb_core.h and use the definition in musb.h.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_core already has musb_get_mode(), so remove the duplicate from
musb_dsps.c.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both musb_io and musb_platform_ops in struct musb define a quirks flag
for the same purpose. Let's remove the one in struct musb_io, and use
that in struct musb_platform_ops instead.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following wrappers were defined because of Blackfin support. Now
Blackfin support is removed, these wrappers are no longer needed, so
remove them.
musb_write_txfifosz
musb_write_txfifoadd
musb_write_rxfifosz
musb_write_rxfifoadd
musb_write_ulpi_buscontrol
musb_read_txfifosz
musb_read_txfifoadd
musb_read_rxfifosz
musb_read_rxfifoadd
musb_read_ulpi_buscontrol
musb_read_hwvers
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, nobody uses adjust_channel_params() any
more, so remove it from struct musb_platform_ops.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, we no longer need function pointers for
musb_readl() and musb_writel().
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, header musbhsdma.h is only included in
musbhsdma.c. So let's merge the content in musbhsdma.h to musbhsdma.c
and delete musbhsdma.h.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support hardware-level Xon/Xoff flow control in transmit direction with
pl2303.
I only know how to get the hardware to do IXON/!IXANY with ^S/^Q as control
characters, so I preserve the old behaviour for all other cases.
Signed-off-by: Florian Zumbiehl <florz@florz.de>
[ johan: rewrite logic using pl2303_termios_change() helper ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the somewhat convoluted hardware-assisted flow control
handling.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop urb_ prefixes from value and index variables used in control
requests.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Replace all __u types with their u counterparts throughout the driver
(whose structures are not exported to user space).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since forever this driver has had IXON and IXOFF mixed up, and has used
the latter rather than the former to enable hardware-assisted software
flow control on output.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
When _param is unsigned and the minimum value of range is 0, it gives
the following warning:
COVERITY NO_EFFECT: This less-than-zero comparison of an unsigned value
is never true.
Converting ._param to int to avoid this warning.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver cause double phy_put()
calling. This driver must not call phy_put() in the remove because
the driver calls devm_phy_get() in the probe.
Fixes: 279d4bc640 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that reconnection is possible to fail
because unexpected state handling happens by the irqs. To fix the issue,
the driver disables the controller's irqs when disconnected.
Fixes: 746bfe63bb ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver ignores errors other than
the non-existence of the device, f.e. a memory allocation failure
in devm_phy_get(). So, this patch replaces devm_phy_get() with
devm_phy_optional_get().
Reported-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: 279d4bc640 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver cannot call phy_init()
if a gadget driver is alreadly loaded because usb_add_gadget_udc()
might call renesas_usb3_start() via .udc_start.
This patch also revises the typo (s/an optional/optional/).
Fixes: 279d4bc640 ("usb: gadget: udc: renesas_usb3: add support for generic phy")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver causes panic if a gadget
driver is already loaded because usb_add_gadget_udc() might call
renesas_usb3_start() via .udc_start, and then pm_runtime_get_sync()
in renesas_usb3_start() doesn't work correctly.
Note that the usb3_to_dev() macro should not be called at this timing
because the macro uses the gadget structure.
Fixes: cf06df3fae ("usb: gadget: udc: renesas_usb3: move pm_runtime_{en,dis}able()")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that this driver doesn't remove its debugfs.
Fixes: 43ba968b00 ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc3_ep_dequeue() waits for completion of End Transfer command using
wait_event_lock_irq(), which will release the dwc3->lock while waiting
and reacquire after completion. This allows a potential race condition
with ep_disable() which also removes all requests from started_list
and pending_list.
The check for NULL r->trb should catch this but currently it exits to
the wrong 'out1' label which calls dwc3_gadget_giveback(). Since its
list entry was already removed, if CONFIG_DEBUG_LIST is enabled a
'list_del corruption' bug is thrown since its next/prev pointers are
already LIST_POISON1/2. If r->trb is NULL it should simply exit to
'out0'.
Fixes: cf3113d893 ("usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following sparse warning:
drivers/usb/dwc3/gadget.c:169:6: warning:
symbol 'dwc3_gadget_del_and_unmap_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix to return error code -ENOMEM from the alloc fail error handling
case instead of 0, as done elsewhere in this function.
Fixes: ecd29dabb2 ("usb: dwc2: pci: Handle error cleanup in probe")
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By clearing NAK status of EP, core will send ZLP
to IN token and assert NAK interrupt relying
on TxFIFO status only.
The WA applies only to core versions from 2.72a
to 4.00a (including both). Also for FS_IOT_1.00a
and HS_IOT_1.00a.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devm_regulator_get_optional returns -ENODEV if the regulator isn't
there, so if that's the case we have to make sure not to leave -ENODEV
in the regulator pointer.
Also, make sure we return 0 in that case, but correctly propagate any
other errors. Also propagate the error from _dwc2_hcd_start.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external vbus supply")
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 4.17-rc, commit 03ea6d6e9e ("usb: dwc2: Enable power down")
caused the HiKey board to not correctly handle switching between
usb-gadget and usb-host mode.
Unplugging the OTG port would result in:
[ 42.240973] dwc2 f72c0000.usb: dwc2_restore_host_registers: no host registers to restore
[ 42.249066] dwc2 f72c0000.usb: dwc2_host_exit_hibernation: failed to restore host registers
And the USB-host ports would not function.
And plugging in the OTG port, we would see:
[ 46.046557] WARNING: CPU: 3 PID: 6 at drivers/usb/dwc2/gadget.c:260 dwc2_hsotg_init_fifo+0x194/0x1a0
[ 46.055761] CPU: 3 PID: 6 Comm: kworker/u16:0 Not tainted 4.17.0-rc5-00030-ge67da8c #231
[ 46.055767] Hardware name: HiKey Development Board (DT)
[ 46.055784] Workqueue: dwc2 dwc2_conn_id_status_change
...
Thus, this patch sets the hisi params to disable the power_down
flag by default, and gets thing working again.
Cc: John Youn <johnyoun@synopsys.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Artur Petrosyan <arturp@synopsys.com>
Cc: Grigor Tovmasyan <tovmasya@synopsys.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added descriptions for all not described parameters.
Fix all kernel doc's warnings.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Introduce FSL_USB2_PHY_UTMI_DUAL in gadget driver for setting
phy in SOCs with utmi dual phy
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Tested-by: Tiago Brusamarello <tbrusa@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix sparse warning
Fixes: 5f0b74e548 ("USB: dwc3: get extcon device by OF graph bindings")
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We dont' need to touch req->direction or req->epnum from
ep_queue(). It's enough that we initialize both fields from
alloc_request() and just keep them for the entire lifetime of the
request.
No functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of *always* calling dwc3_gadget_ep_get_transfer_index() after
sending a Start Transfer command, we can call it once from
dwc3_send_gadget_ep_cmd() itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of returning resource index number just to assign it to a
field inside 'dep' which was passed as argument, we can assing
dep->resource_index from inside dwc3_gadget_ep_get_transfer_index()
itself.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we have many started requests and one of them in the middle is
completed with Missed Isoc, let's not End Transfer as that would
result in us loosing (possibly) many more intervals.
Instead, let's allow the controller to go through its list of started
requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
XferNotReady and XferInProgress give us the uFrame number we're
currently in. Printing that out on tracepoints may help us find bugs
in transfer scheduling.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Avoid a prototype when the function can be defined earlier. No
functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of having a prototype for a function that's defined a few
lines down, let's just move definition to the place where prototype
was.
No functional changes, cleanup only.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In a few places, the argument is completely unnecessary. On places
where it's needed, we can get it from dep->dwc.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Those two arguments refer to a single bitfield in the register. In
order to simplify the code, we can combine them into a single argument
and expect caller to pass the correct action argument at all times.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will only have event status of IOC when IOC bit is set in
TRB. There's no need to check both bits.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We know that only OUT endpoints can trigger SHORT. We also know that
count MUST be > 0 whenever SHORT triggers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This will make it easier to figure out the reason for the event. That
information really helps debugging certain problems.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We are trying to kick transfers on Isochronous endpoints in a more
controlled manner now. And this ended up rendering this piece of code
unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of having one big loop, let's split it down into two smaller
handlers: one for linear buffers and one for scatterlist.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After all the previous changes, it's now a lot clearer how isoc
transfers should be managed. We don't need to try to End Transfers
from ep_queue since that's already done by cleanup_requests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now, this part of the code is duplicated and brings no extra value to
the driver. Let's remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case we get an event with status set to Missed Isoc, this means we
have missed an isochronous interval and should issue End Transfer
command and wait for the following XferNotReady.
Let's do that early, rather than late.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By now, it has the same semantics as DWC3_EP_TRANSFER_STARTED, but
that has a much more descriptive name.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We will need an up-to-date frame_number from XferInProgress too when
future patches improve our handling of Isoc endpoints.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The core requires the extra two bits of information for properly
scheduling Isochronous transfers. This means that we can't rely on
__dwc3_gadget_get_frame(). Let's always cache uFrame number from
XferNotReady instead.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Endpoint handlers need to know about endpoints, not dwc. If they
really need access to dwc (e.g. for printing error messages) we have a
reference to it tucked inside the endpoint.
This patch has no functional changes, it's simply moving things around.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We *KNOW* which events we enable for which endpoint types and
we *KNOW* when they'll trigger. The endpoint type checks are
pointless.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch simply renames two functions to more descriptive names so
that it's easier to understand what they're doing.
Cleanup only, no functional changes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of constantly calling kick transfer everything some event
shows up, let's just rely on the fact that we send Update Transfer
every time a new request is queued.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we're making sure we don't have XferComplete events, we can
rename this function to what it actually handles:
dwc3_gadget_endpoint_transfer_in_progress()
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
XferComplete is enabled only for the default control pipe, let's make
that clear in the code.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We don't use XferNotReady for anything other than Default Control
Pipe, which is handled in ep0.c, and Isochronous endpoints. Let's make
that clear in the code.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Interrupt endpoints behave much like Bulk endpoints with the exception
that they are periodic. We can pre-issue Start Transfer exactly as we
do for Bulk endpoints.
While at that, remove one trailing blank line which is unnecessary.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The present code correctly fetches the req which were previously not
queued from the started_list but fails to continue queuing from the sg
where it previously stopped queuing (because of the unavailable TRB's).
This patch correct's the code to continue queuing from the correct sg
present in the sglist.
For example, consider 5 sgs in req. Because of limited TRB's among the
5 sgs only 3 got queued. This patch corrects the code to start queuing
from correct sg i.e 4th sg when the TRBs are available.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The code logic in dwc3_prepare_one_trb() incorrectly uses the address
and length fields present in req packet for mapping TRB's instead of
using the address and length fields of scattergather lists. This patch
correct's the code to use sg->address and sg->length when scattergather
lists are present.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
All T&M instruments should also work with rigol_quirk = 1 code path.
So remove unnecessary code in rigol_quirk = 0 code path to simplify the driver.
Tested-by: Dave Penkler <dpenkler@gmail.com>
Reviewed-by: Steve Bayless <steve_bayless@keysight.com>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have the tty port when probing a usb-serial port so use
tty_port_register_device() directly instead of tty_port_install() later
to set up the port link.
This is a step towards enabling serdev for usb-serial (but we need to
determine how to handle hotplugging first).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
stub_probe() calls put_busid_priv() in an error path when device isn't
found in the busid_table. Fix it by making put_busid_priv() safe to be
called with null struct bus_id_priv pointer.
This problem happens when "usbip bind" is run without loading usbip_host
driver and then running modprobe. The first failed bind attempt unbinds
the device from the original driver and when usbip_host is modprobed,
stub_probe() runs and doesn't find the device in its busid table and calls
put_busid_priv(0 with null bus_id_priv pointer.
usbip-host 3-10.2: 3-10.2 is not in match_busid table... skip!
[ 367.359679] =====================================
[ 367.359681] WARNING: bad unlock balance detected!
[ 367.359683] 4.17.0-rc4+ #5 Not tainted
[ 367.359685] -------------------------------------
[ 367.359688] modprobe/2768 is trying to release lock (
[ 367.359689]
==================================================================
[ 367.359696] BUG: KASAN: null-ptr-deref in print_unlock_imbalance_bug+0x99/0x110
[ 367.359699] Read of size 8 at addr 0000000000000058 by task modprobe/2768
[ 367.359705] CPU: 4 PID: 2768 Comm: modprobe Not tainted 4.17.0-rc4+ #5
Fixes: 22076557b0 ("usbip: usbip_host: fix NULL-ptr deref and use-after-free errors") in usb-linus
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
extcon device is used to detect host/device connection. Since extcon
OF property is deprecated, alternative method should be added.
This method uses OF graph bindings to locate extcon.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Historically, the clocks and resets are handled on the glue layer
side instead of the DWC3 core. For simple cases, dwc3-of-simple.c
takes care of arbitrary number of clocks and resets. The DT node
structure typically looks like as follows:
dwc3-glue {
compatible = "foo,dwc3";
clocks = ...;
resets = ...;
...
dwc3 {
compatible = "snps,dwc3";
...
};
}
By supporting the clocks and the reset in the dwc3/core.c, it will
be turned into a single node:
dwc3 {
compatible = "foo,dwc3", "snps,dwc3";
clocks = ...;
resets = ...;
...
}
This commit adds the binding of clocks and resets specific to this IP.
The number of clocks should generally be the same across SoCs, it is
just some SoCs either tie clocks together or do not provide software
control of some of the clocks.
I took the clock names from the Synopsys datasheet: "ref" (ref_clk),
"bus_early" (bus_clk_early), and "suspend" (suspend_clk).
I found only one reset line in the datasheet, hence the reset-names
property is omitted.
Those clocks are required for new platforms. Enforcing the new
binding breaks existing platforms since they specify clocks (and
resets) in their glue layer node, but nothing in the core node.
I listed such exceptional cases in the DT binding. The driver
code has been relaxed to accept no clock. This change is based
on the discussion [1].
I inserted reset_control_deassert() and clk_bulk_enable() before the
first register access, i.e. dwc3_cache_hwparams().
[1] https://patchwork.kernel.org/patch/10284265/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Just set up the show callback in the tty_operations, and use
proc_create_single_data to create the file without additional
boilerplace code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Variants of proc_create{,_data} that directly take a seq_file show
callback and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
usbip_host updates device status without holding lock from stub probe,
disconnect and rebind code paths. When multiple requests to import a
device are received, these unprotected code paths step all over each
other and drive fails with NULL-ptr deref and use-after-free errors.
The driver uses a table lock to protect the busid array for adding and
deleting busids to the table. However, the probe, disconnect and rebind
paths get the busid table entry and update the status without holding
the busid table lock. Add a new finer grain lock to protect the busid
entry. This new lock will be held to search and update the busid entry
fields from get_busid_idx(), add_match_busid() and del_match_busid().
match_busid_show() does the same to access the busid entry fields.
get_busid_priv() changed to return the pointer to the busid entry holding
the busid lock. stub_probe(), stub_disconnect() and stub_device_rebind()
call put_busid_priv() to release the busid lock before returning. This
changes fixes the unprotected code paths eliminating the race conditions
in updating the busid entries.
Reported-by: Jakub Jirasek
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After removing usbip_host module, devices it releases are left without
a driver. For example, when a keyboard or a mass storage device are
bound to usbip_host when it is removed, these devices are no longer
bound to any driver.
Fix it to run device_attach() from the module exit routine to restore
the devices to their original drivers. This includes cleanup changes
and moving device_attach() code to a common routine to be called from
rebind_store() and usbip_host_exit().
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device is left in the busid_table after unbind and rebind. Rebind
initiates usb bus scan and the original driver claims the device.
After rescan the device should be deleted from the busid_table as
it no longer belongs to usbip_host.
Fix it to delete the device after device_attach() succeeds.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refine probe and disconnect debug msgs to be useful and say what is
in progress.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the fallout of the conversion to GPIO descriptors in 3df0340810.
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The include defines the private platform_data structure used with AVR
platforms. It has no user since 7c55984e19. Remove it.
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When converting to GPIO descriptors, gpiod_get_value automatically
handles the line inversion flags from the device tree.
Do not invert the line twice.
Fixes: 3df0340810 ("usb: gadget: udc: atmel: convert to use GPIO descriptors")
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
A message can be forged to crash the stack; here we make sure we don't
completely break the system if this occurs
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It is not a good idea to directly modify the resource of a platform
device. Modify its local copy, and pass it to devm_ioremap_resource()
so that we do not need to restore it in the failure path and the remove
hook.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB3CV version 2.1.80 (March 26, 2018) requires all devices
( gen1, gen2, single lane, dual lane) to return the value of 0x0320
in the bcdUSB field
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some PHY drivers (e.g. for Qualcomm QUSB2 and QMP PHYs) support
runtime PM to reduce PHY power consumption during bus_suspend.
Add changes to let core auto-suspend PHYs on host bus-suspend
using GUSB2PHYCFG register if needed for a platform. Also perform
PHYs runtime suspend/resume and let platform glue drivers e.g.
dwc3-qcom handle remote wakeup during bus suspend by waking up
devices on receiving wakeup event from PHY.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 controller on Qualcomm SOCs has a Qscratch wrapper.
Some of its uses are described below resulting in need to
have a separate glue driver instead of using dwc3-of-simple:
- It exposes register interface to override vbus-override
and lane0-pwr-present signals going to hardware. These
must be updated in peripheral mode for DWC3 if vbus lines
are not connected to hardware block. Otherwise RX termination
in SS mode or DP pull-up is not applied by device controller.
- pwr_events_irq_stat support to check if USB2 PHY is in L2 state
before glue driver proceeds with suspend.
- Support for wakeup interrupts lines that are asserted whenever
there is any wakeup event on USB3 or USB2 bus.
- Support to replace pip3 clock going to DWC3 with utmi clock
for hardware configuration where SSPHY is not used with DWC3.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add compatible string to use this generic glue layer to support
Allwinner H6 platform's dwc3 controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case there are multiple ecm instances, either for multiple
otg controllers, or multiple virtual links using libcomposite,
each instance needs to have its own host mac address string
value for iMACAddress.
Update the source array (ecm_string_defs), every time before
usb_gstrings_attach(). Without that, all links wrongly were
getting the same, last allocated, host mac address, rather
than the correct one, as requested via configfs.
Signed-off-by: Lukasz Nowak <lukasz.nowak@exablue.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes: <b3e3893e1253> ("net: use core MTU range checking")
which patched only one of two functions used to setup the
USB Gadget Ethernet driver, causing a serious performance
regression in the ability to increase mtu size above 1500.
Signed-off-by: John Greb <h3x4m3r0n@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current frame_number is read from core for both
device and host modes. Reading of the current frame
number needs to be performed ASAP due to IRQ latency's.
This is why, it is moved to common interrupt handler.
Accordingly updated dwc2_gadget_target_frame_elapsed()
function which uses stored frame_number instead of
reading frame number.
In cases when target frame value is incremented
the frame_number is required to read again.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Dumping the registers via debugfs makes USB on Raspberry Pi completely
unusable. The read of register GRXSTSP ("Receive Status Read and Pop
Register") is responsible for this behaviour, because it pops the RX FIFO.
So avoid this by omitting the relevant register.
CC: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Fixes: 563cf017c4 ("usb: dwc2: debugfs: add support for complete register dump")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Crash caused by going out of "eps_out" array range.
Iteration on "eps_out" changed to less than "num_of_eps".
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_IPG_ISOC_SUPPORTED and DCFG_IPG_ISOC_SUPPORDED
bits definitions to enable/disable IPG feature.
Added ipg_isoc_en core parameter which will indicate IPG support
enable/disable and initialize it.
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In DDMA mode required to enable BNA interrupt for
both directions.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Changed existing two descriptor-chain flow to one chain.
In two-chain implementation BNA interrupt used for switching between
two chains. BNA interrupt asserted because of returning to
beginning of the chain based on L-bit of last descriptor.
Because of that we lose packets. This issue resolved by using one
desc-chain.
Removed all staff related to two desc-chain flow from
DDMA ISOC related functions.
Removed request length checking from dwc2_gadget_fill_isoc_desc()
function. Request length checking added to dwc2_hsotg_ep_queue()
function. If request length greater than descriptor limits then
request not added to queue. Additional checking done for High
Bandwidth ISOC OUT's which not supported by driver. In
dwc2_gadget_fill_isoc_desc() function also checked desc-chain
status (full or not) to avoid of reusing not yet processed
descriptors.
In dwc2_gadget_start_isoc_ddma() function creation of desc-chain
always started from descriptor 0. Before filling descriptors, they
were initialized by HOST BUSY status.
In dwc2_gadget_complete_isoc_request_ddma() added checking for
desc-chain rollover. Also added checking completion status.
Request completed successfully if DEV_DMA_STS is DEV_DMA_STS_SUCC,
otherwise complete with actual=0. For systems with high IRQ latency
added pointer compl_desc to next descriptor to be completed by
XferCompl interrupt. This pointer replace descriptor index calculation
based on DxEPDMA register. On descriptor completion interrupt
processing all descriptors starting from compl_desc till descriptor
which Buffer Status field not equal DMA_DONE status.
Actually removed dwc2_gadget_start_next_isoc_ddma() function because
now driver use only one desc-chain and instead that function added
dwc2_gadget_handle_isoc_bna() function for handling BNA interrupts.
Handling BNA interrupt done by flushing TxFIFOs for OUT EPs,
completing request with actual=0 and resetting desc-chain number and
target frame to initial values for restarting transfers.
On handling NAK request completed with actual=0. Incremented target
frame to allow fill desc chain and start transfers.
In DDMA mode avoided of frame number incrementing, because tracking
of frame number performed in dwc2_gadget_fill_isoc_desc() function.
When core assert XferCompl along with BNA, we should ignore XferCompl
in dwc2_hsotg_epint() function.
On BNA interrupt replaced dwc2_gadget_start_next_isoc_ddma() by above
mentioned BNA handler.
In dwc2_hsotg_ep_enable() function added sanity check of bInterval
for ISOC IN in DDMA mode, because HW doesn't supported EP's with
bInterval more than 10 and check for mc for ISOC OUT transfers,
because core doesn't support high bandwidth transfers.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In fact the driver depends on EXTCON only when it's configed as
USB_MTU3_DUAL_ROLE, so make USB_MTU3_DUAL_ROLE depend on EXTCON but
not USB_MTU3.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is an error dialog popped up in PC when test TEST_J/K
by EHSETT tool, due to not waiting for the completion of
control transfer. Here fix it by entering test mode after
Status Stage finish.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When boot on the platform with the USB cable connected to Win7,
the Win7 will pop up an error dialog: "USB Device not recognized",
but finally the Win7 can enumerate it successfully.
The root cause is as the following:
When the xHCI driver set PORT_POWER of the OTG port, and if both
IDPIN and VBUS_VALID are high at the same time, the MTU3 controller
will set SESSION and pull up DP, so the Win7 can detect existence
of USB device, but if the mtu3 driver can't switch to device mode
during the debounce time, the Win7 can not enumerate it.
Here to fix it by removing the 1s delayed EXTCON register to speed up
mode switch.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The usb_add_gadget_udc() will set the gadget state as
USB_STATE_NOTATTACHED, so we needn't set it again.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The variable of 'count' is declared as u8, this will cause an issue
due to value truncated when works in SS or SSP mode and data length
is greater than 255, so change it as u32.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Tegra's EHCI driver has a build dependency on Tegra's PHY driver and
currently Tegra's PHY driver is built only when Tegra's EHCI driver is
built. Add own Kconfig entry for the Tegra's PHY driver so that drivers
other than ehci-tegra (like ChipIdea UDC) could work with ehci-tegra
driver being disabled in kernels config by allowing user to manually
select the PHY driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
UTMI pads are shared by USB controllers and reset of UTMI pads is shared
with the reset of USB1 controller. Currently reset of UTMI pads is done by
the EHCI driver and ChipIdea UDC works because EHCI driver always happen
to be probed first. Move reset controls from ehci-tegra to tegra-phy in
order to resolve the problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Tegra's PHY driver has a mix of pr_err() and dev_err(), let's switch to
dev_err() and use common errors message formatting across the driver for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This allows 32 bit owners of ffs endpoints to
make ioctls into a 64 bit kernel.
All of the current epfile ioctls can be handled
with the same struct definitions as regular
ioctl.
Acked-by: Michał Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently, the midi function is not freed until it is
both removed from the config and released by the user.
Since the user could take a long time to release the
card, it's possible that the function could be unlinked
and thus f_midi_opts would be null when freeing f_midi.
Thus, refcount f_midi_opts and only free it when it is
unlinked and all f_midis have been freed.
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The Aspeed BMC SoCs support a "virtual hub" function. It provides some
HW support for a top-level USB2 hub behind which sit 5 gadget "ports".
This driver adds support for the full functionality, emulating the
hub standard requests and exposing 5 UDC gadget drivers corresponding
to the ports.
The hub itself has HW provided dedicated EP0 and EP1 (the latter for
hub interrupts). It also has dedicated EP0s for each function. For
other endpoints, there's a pool of 15 "generic" endpoints that are
shared among the ports.
The driver relies on my previous patch adding a "dispose" EP op to
handle EP allocation between ports. EPs are allocated from the shared
pool in the UDC "match_ep" callback and assigned to the UDC instance
(added to the gadget ep_list).
When the composite driver gets unbound, the new hook will allow the UDC
to clean things up and return those EPs to the shared pool.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The table is never modified by the function. This allows us
to use it on a statically defined table that is marked const.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It has been observed that writing 0xF2 to the power register while it
reads as 0xF4 results in the register having the value 0xF0, i.e. clearing
RESUME and setting SUSPENDM in one go does not work. It might also violate
the USB spec to transition directly from resume to suspend, especially
when not taking T_DRSMDN into account. But this is what happens when a
remote wakeup occurs between SetPortFeature USB_PORT_FEAT_SUSPEND on the
root hub and musb_bus_suspend being called.
This commit returns -EBUSY when musb_bus_suspend is called while remote
wakeup is signalled and thus avoids to reset the RESUME bit. Ignoring
this error when musb_port_suspend is called from musb_hub_control is ok.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hub driver will try to disable a USB3 device twice at logical disconnect,
racing with xhci_free_dev() callback from the first port disable.
This can be triggered with "udisksctl power-off --block-device <disk>"
or by writing "1" to the "remove" sysfs file for a USB3 device
in 4.17-rc4.
USB3 devices don't have a similar disabled link state as USB2 devices,
and use a U3 suspended link state instead. In this state the port
is still enabled and connected.
hub_port_connect() first disconnects the device, then later it notices
that device is still enabled (due to U3 states) it will try to disable
the port again (set to U3).
The xhci_free_dev() called during device disable is async, so checking
for existing xhci->devs[i] when setting link state to U3 the second time
was successful, even if device was being freed.
The regression was caused by, and whole thing revealed by,
Commit 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned.
and causes a NULL pointer dereference the second time we try to set U3.
Fix this by checking xhci->devs[i]->udev exists before setting link state.
The original patch went to stable so this fix needs to be applied there as
well.
Fixes: 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
Cc: <stable@vger.kernel.org>
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix for a long-standing issue in the visor driver, which could
have security implications. Included is also a new modem device id.
Both commits have been in linux-next for a couple of days with no
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=jWQ/
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.17-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.17-rc4
Here's a fix for a long-standing issue in the visor driver, which could
have security implications. Included is also a new modem device id.
Both commits have been in linux-next for a couple of days with no
reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 22072e83eb as it is
broken.
Alan writes:
What you can't see just from reading the patch is that in both
cases (ehci->itd_pool and ehci->sitd_pool) there are two
allocation paths -- the two branches of an "if" statement -- and
only one of the paths calls dma_pool_[z]alloc. However, the
memset is needed for both paths, and so it can't be eliminated.
Given that it must be present, there's no advantage to calling
dma_pool_zalloc rather than dma_pool_alloc.
Reported-by: Erick Cafferata <erick@cafferata.me>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After removing usbip_host module, devices it releases are left without
a driver. For example, when a keyboard or a mass storage device are
bound to usbip_host when it is removed, these devices are no longer
bound to any driver.
Fix it to run device_attach() from the module exit routine to restore
the devices to their original drivers. This includes cleanup changes
and moving device_attach() code to a common routine to be called from
rebind_store() and usbip_host_exit().
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device is left in the busid_table after unbind and rebind. Rebind
initiates usb bus scan and the original driver claims the device.
After rescan the device should be deleted from the busid_table as
it no longer belongs to usbip_host.
Fix it to delete the device after device_attach() succeeds.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the I2C adapter that the PD controller is attached to
does not support SMBus protocol, the driver needs to handle
block reads separately. The first byte returned in block
read protocol will show the total number of bytes. It needs
to be stripped away.
This is handled separately in the driver only because right
now we have no way of requesting the used protocol with
regmap-i2c. This is in practice a workaround for what is
really a problem in regmap-i2c. The other option would have
been to register custom regmap, or not use regmap at all,
however, since the solution is very simple, I choose to use
it in this case for convenience. It is easy to remove once
we figure out how to handle this kind of cases in
regmap-i2c.
Fixes: 0a4c005bd1 ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ref count for the USB role switch device must be
released after we are done using the switch.
Fixes: c6962c2972 ("usb: typec: tcpm: Set USB role switch to device mode when configured as such")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some non-compliant high-speed USB devices have bulk endpoints with a
1024-byte maxpacket size. Although such endpoints don't work with
xHCI host controllers, they do work with EHCI controllers. We used to
accept these invalid sizes (with a warning), but we no longer do
because of an unintentional change introduced by commit aed9d65ac3
("USB: validate wMaxPacketValue entries in endpoint descriptors").
This patch restores the old behavior, so that people with these
peculiar devices can use them without patching their kernels by hand.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Elvinas <elvinas@veikia.lt>
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN found a use-after-free in xhci_free_virt_device+0x33b/0x38e
where xhci_free_virt_device() sets slot id to 0 if udev exists:
if (dev->udev && dev->udev->slot_id)
dev->udev->slot_id = 0;
dev->udev will be true even if udev is freed because dev->udev is
not set to NULL.
set dev->udev pointer to NULL in xhci_free_dev()
The original patch went to stable so this fix needs to be applied
there as well.
Fixes: a400efe455 ("xhci: zero usb device slot_id member when disabling and freeing a xhci slot")
Cc: <stable@vger.kernel.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we get an invalid device configuration from a palm 3 type device, we
might incorrectly parse things, and we have the potential to crash in
"interesting" ways.
Fix this up by verifying the size of the configuration passed to us by
the device, and only if it is correct, will we handle it.
Note that this also fixes an information leak of slab data.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ johan: add comment about the info leak ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for ublox R410M PID 0x90b2 USB modem to option
driver, this module supports LTE Cat M1 / NB1.
Interface layout:
0: QCDM/DIAG
1: ADB
2: AT
3: RMNET
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The dwm-158 interface 4 and 5 doesn't answer to the AT commands
and doesn't appears a option interface.
Tested on openwrt distribution (kernel 4.14 using the old blacklist
definitions).
Lars Melin also writes:
Blacklisting interface 4 and 5 is correct because:
MI_00 D-Link Mobile Broadband Device (cdc_ether)
MI_02 D-Link HSPA+DataCard Diagnostics Interface (also ppp modem)
MI_03 D-Link HSPA+DataCard NMEA Device
MI_04 D-Link HSPA+DataCard Speech Port
MI_05 D-Link HSPA+DataCard Debug Port
MI_06 USB Mass Storage Device
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
[ johan: add Lars's comment on the interface layout and reword summary ]
Cc: Lars Melin <larsm17@gmail.com>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The usb_request pointer could be NULL in musb_g_tx(), where the
tracepoint call would trigger the NULL pointer dereference failure when
parsing the members of the usb_request pointer.
Move the tracepoint call to where the usb_request pointer is already
checked to solve the issue.
Fixes: fc78003e53 ("usb: musb: gadget: add usb-request tracepoints")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_start_urb() doesn't check the pass-in parameter if it is NULL. But
in musb_bulk_nak_timeout() the parameter passed to musb_start_urb() is
returned from first_qh(), which could be NULL.
So wrap the musb_start_urb() call here with a if condition check to
avoid the potential NULL pointer dereference.
Fixes: f283862f3b ("usb: musb: NAK timeout scheme on bulk TX endpoint")
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, logical and is being used instead of *bitwise* and.
Fix this by using a proper bitwise and operator.
Addresses-Coverity-ID: 1468455 ("Logical vs. bitwise operator")
Fixes: 64f7c494a3 ("typec: tcpm: Add support for sink PPS related messages")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not much this time around: A list_del corruption on dwc3_ep_dequeue(),
sparse warning fix also on dwc3, build issues with f_phonet.
Apart from these three, some other minor fixes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
-----BEGIN PGP SIGNATURE-----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=8ivE
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.17-rc3
Not much this time around: A list_del corruption on dwc3_ep_dequeue(),
sparse warning fix also on dwc3, build issues with f_phonet.
Apart from these three, some other minor fixes.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This resolves the merge issue with drivers/usb/core/hcd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trivial fix to spelling mistake in text string
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a few device ids for -rc3, including a new "simple driver".
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=5u11
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.17-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.17-rc3
Here are a few device ids for -rc3, including a new "simple driver".
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
gcc thinks it is too smart and gives off a "you might be using this
variable before it is initialized" warning in tcpm_pd_build_request(),
because it can not follow the logic through the tcpm_pd_select_pdo()
call.
So just make gcc quiet by initializing things to 0, to prevent the
myriad of people complaining that we now have a build warning.
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds sink side support for Get_Status, Status,
Get_PPS_Status and PPS_Status handling. As there's the
potential for a partner to respond with Not_Supported,
handling of this message is also added. Sending of
Not_Supported is added to handle messagescreceived but not
yet handled.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a power_supply class instance to represent a
PD source's voltage and current properties. This provides an
interface for reading these properties from user-space or other
drivers.
For PPS enabled Sources, this also provides write access to set
the current and voltage and allows for swapping between standard
PDO and PPS APDO.
As this represents a superset of the information provided in the
fusb302 driver, the power_supply instance in that code is removed
as part of this change, so reverting the commit titled
'typec: tcpm: Represent source supply through power_supply class'
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds code to handle requesting of PPS APDOs. Switching
between standard PDOs and APDOs, and re-requesting an APDO to
modify operating voltage/current will be triggered by an
external call into TCPM.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some low-speed and full-speed devices (for example, bluetooth)
do not have time to initialize. For them, ETIMEDOUT is a valid error.
We need to give them another try. Otherwise, they will
never be initialized correctly and in dmesg will be messages
"Bluetooth: hci0 command 0x1002 tx timeout" or similars.
Fixes: 264904ccc3 ("usb: retry reset if a device times out")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Moseychuk <franchesko.salias.hudro.pedros@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc3_ep_dequeue() waits for completion of End Transfer command using
wait_event_lock_irq(), which will release the dwc3->lock while waiting
and reacquire after completion. This allows a potential race condition
with ep_disable() which also removes all requests from started_list
and pending_list.
The check for NULL r->trb should catch this but currently it exits to
the wrong 'out1' label which calls dwc3_gadget_giveback(). Since its
list entry was already removed, if CONFIG_DEBUG_LIST is enabled a
'list_del corruption' bug is thrown since its next/prev pointers are
already LIST_POISON1/2. If r->trb is NULL it should simply exit to
'out0'.
Fixes: cf3113d893 ("usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fixes the following sparse warning:
drivers/usb/dwc3/gadget.c:169:6: warning:
symbol 'dwc3_gadget_del_and_unmap_request' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix to return error code -ENOMEM from the alloc fail error handling
case instead of 0, as done elsewhere in this function.
Fixes: ecd29dabb2 ("usb: dwc2: pci: Handle error cleanup in probe")
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By clearing NAK status of EP, core will send ZLP
to IN token and assert NAK interrupt relying
on TxFIFO status only.
The WA applies only to core versions from 2.72a
to 4.00a (including both). Also for FS_IOT_1.00a
and HS_IOT_1.00a.
Signed-off-by: Artur Petrosyan <arturp@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
devm_regulator_get_optional returns -ENODEV if the regulator isn't
there, so if that's the case we have to make sure not to leave -ENODEV
in the regulator pointer.
Also, make sure we return 0 in that case, but correctly propagate any
other errors. Also propagate the error from _dwc2_hcd_start.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external vbus supply")
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since commit 39cee200c2 ("usb: musb: core: call init and shutdown for
the usb phy") the musb USB phy is initialised by musb_core, but the
original initialisation in the dsps-glue init callback was left in
place resulting in two calls to phy init during probe (and similarly,
two shutdowns on remove).
Drop the duplicate phy init and shutdown calls from the dsps glue in
favour of the ones in musb core, which other glue drivers rely on.
Note however that any generic phy is still initialised in the glue init
callback (just as for the other drivers).
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the new HCD flag which prevents USB core from trying to manage our
phys.
This is needed to be able to associate the controller platform device
with the glue device device-tree node on the BBB which uses legacy USB
phys. Otherwise, the generic phy lookup in usb_phy_roothub_init() and
thus HCD registration fails repeatedly with -EPROBE_DEFER (see commit
178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD
core")).
Note that a related phy-lookup issue was recently worked around in the
phy core by commit b7563e2796 ("phy: work around 'phys' references to
usb-nop-xceiv devices"). Something similar may now be needed for other
USB phys, and in particular if we eventually want to let USB core manage
musb generic phys.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1468266 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve the kerneldoc for usb_ep_queue() to note explicitly that the
request's completion routine will be called if and only if the return
value is 0. The corresponding fact about usb_submit_urb() for the
host-side API has long been documented, and this has always been the
intention for the gadget API. But until now, documentation seems to
have been lacking.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Tegra's EHCI driver has a build dependency on Tegra's PHY driver and
currently Tegra's PHY driver is built only when Tegra's EHCI driver is
built. Add own Kconfig entry for the Tegra's PHY driver so that drivers
other than ehci-tegra (like ChipIdea UDC) could work with ehci-tegra
driver being disabled in kernels config by allowing user to manually
select the PHY driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UTMI pads are shared by USB controllers and reset of UTMI pads is shared
with the reset of USB1 controller. Currently reset of UTMI pads is done by
the EHCI driver and ChipIdea UDC works because EHCI driver always happen
to be probed first. Move reset controls from ehci-tegra to tegra-phy in
order to resolve the problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra's PHY driver has a mix of pr_err() and dev_err(), let's switch to
dev_err() and use common errors message formatting across the driver for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This clarifies the license of the code. While here also add an include
guard to the header file.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add rx_lanes and tx_lanes lane count sysfs entries for a usb device
struct usb_devuce rx_lanes and tx_lanes variables.
Shows number of lanes used by the usb device
Data rate of a device is the lane speed * lane count, for example
USB 3.2 Gen 2x2 device uses 10Gbps signaling per lane, and has dual-lane
support 10Gbps * 2 = 20Gbps
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.2 specification adds a Gen XxY notion for USB3 devices where
X is the signaling rate on the wire. Gen 1xY is 5Gbps Superspeed
and Gen 2xY is 10Gbps SuperSpeedPlus. Y is the lane count.
For normal, non inter-chip (SSIC) devies the rx and tx lane count is
symmetric, and the maximum lane count for USB 3.2 devices is 2 (dual-lane).
SSIC devices may have asymmetric lane counts, with up to four
lanes per direction. The USB 3.2 specification doesn't point out
how to use the Gen XxY notion for these devices, so we limit the Gen Xx2
notion to symmertic Dual lane devies.
For other devices just show Gen1 or Gen2
Gen 1 5Gbps
Gen 2 10Gbps
Gen 1x2 10Gbps Dual-lane (USB 3.2)
Gen 2x2 20Gbps Dual-lane (USB 3.2)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the the rx_lane and tx_lane count to "2" for USB 3.2 hosts.
For all other older hosts set the default lane counts to 1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.2 specification adds Dual-lane support, doubling the maximum
SuperSpeedPlus data rate from 10Gbps to 20Gbps.
Dual-lane takes into use a second set of rx and tx wires/pins in the
Type-C cable and connector.
Add "rx_lanes" and "tx_lanes" variables to struct usb_device to store
the numer of lanes in use. Number of lanes can be read using the extended
port status hub request that was introduced in USB 3.1.
Extended port status rx and tx lane count are zero based, maximum
lanes supported by non inter-chip (SSIC) USB 3.2 is 2 (dual lane) with
rx and tx lane count symmetric. SSIC devices support asymmetric lanes
up to 4 lanes per direction.
If extended port status is not available then default to one lane.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hosts that support USB 3.2 Enhaned SuperSpeed can set their hcd speed
to HCD_USB32 to let usb core and host drivers know that the controller
supports new USB 3.2 dual-lane features.
make sure usb core handle HCD_USB32 hosts correctly, for now similar
to HCD_USB32.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The change was done at xhci-plat level and not at a xhci-mvebu.c because,
it is expected that other SoC would have this kind of constraint.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since there is no user of max_snk_*, so we can remove them from tcpm.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since max_snk_* is to be deprecated, so remove max_snk_* by adding a
variable PDO for sink config.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since max_snk_* is to be deprecated, so remove max_snk_* by adding a
variable PDO for sink config.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is a combination of commit 57e6f0d7b8
("typec: tcpm: Only request matching pdos") and source
pdo selection optimization based on it, instead of only
compare between the same pdo type of sink and source,
we should check source pdo voltage range is within the
voltage range of one sink pdo.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wait_for_connected() wait till a port change status to
USB_PORT_STAT_CONNECTION, but this is not possible if
the port is unpowered. The loop will only exit at timeout.
Such case take place if an over-current incident happen
while system is in S3. Then during resume wait_for_connected()
will wait 2s, which may be noticeable by the user.
Signed-off-by: Dominik Bozek <dominikx.bozek@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy interface for associating controllers with phys from board
files and platform code has been unused since commit 9080b8dc76 ("ARM:
OMAP2+: Remove legacy usb-host.c platform init code"). Since then, all
calls to usb_get_phy_dev() and its devres version have been returning
-ENODEV.
Now that the final calls to these functions have been removed, we can
drop this legacy lookup interface altogether.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for legacy phys for rcar2 which hasn't been used with a
mainline kernel since commit 9080b8dc76 ("ARM: OMAP2+: Remove legacy
usb-host.c platform init code"). Specifically, since that commit
usb_get_phy_dev() have always returned -ENODEV and consequently this
code has not been used.
Note that the legacy-phy API is still being used in gadget mode to bind
the peripheral controller.
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for non-DT systems, which hasn't been used by a mainline
kernel since commit 9080b8dc76 ("ARM: OMAP2+: Remove legacy usb-host.c
platform init code"). Specifically, since that commit usb_get_phy_dev()
have always returned -ENODEV when looking up a legacy phy, something
which in turn would have led to the init callback returning
-EPROBE_DEFER indefinitely.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for looking up legacy phys defined by board files,
something which hasn't been used by a mainline kernel since commit
9080b8dc76 ("ARM: OMAP2+: Remove legacy usb-host.c platform init
code"). Specifically, since that commit usb_get_phy_dev() have always
returned -ENODEV and consequently this code has not been used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for looking up and initialising legacy phys in USB core,
something which hasn't been used by a mainline kernel since commit
9080b8dc76 ("ARM: OMAP2+: Remove legacy usb-host.c platform init
code"). Specifically, since that commit usb_get_phy_dev() have always
returned -ENODEV and consequently this code has not been used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the unused legacy usb_bind_phy() helper whose last user was removed
in 2016 when OMAP moved to device-tree boot (9080b8dc76 ("ARM: OMAP2+:
Remove legacy usb-host.c platform init code")).
Note that this means that for the last couple of years the phy_bind_list
has been empty (when using mainline kernels) and that consequently all
phy lookups using the usb_get_phy_dev() interface have failed with
-ENODEV. This helper along with its current users will be removed by
follow-on patches.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refine probe and disconnect debug msgs to be useful and say what is
in progress.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> [drivers/usb/gadget/]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isp1760_stop() is never called in atomic context.
The call chain ending up at isp1760_stop() is:
[1] isp1760_stop() <- isp1760_shutdown()
isp1760_shutdown() is set as ".shutdown" in struct hc_driver.
isp1760_stop() is also set as ".stop" in hc_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, isp1760_stop()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isp1760_init_core() is never called in atomic context.
The call chains ending up at isp1760_init_core() are:
[1] isp1760_init_core() <- isp1760_register() <- isp1760_plat_probe()
[2] isp1760_init_core() <- isp1760_register() <- isp1761_pci_probe()
isp1760_plat_probe() is set as ".probe" in struct platform_driver.
isp1761_pci_probe() is set as ".probe" in struct pci_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, isp1761_pci_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
init_freecom() is never called in atomic context.
init_freecom() is set as ".initFunction" through UNUSUAL_DEV().
And ->initFunction() is only called by usb_stor_acquire_resources(),
which is only called by usb_stor_probe2().
usb_stor_probe2() is called by *_probe() functions (like alauda_probe())
for each USB driver.
*_probe() functions are set ".probe" in struct usb_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, init_freecom()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap_nocache(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use new return type vm_fault_t for the fault handler
in struct vm_operations_struct. For now, this is just
documenting that the function returns a VM_FAULT value
rather than an errno. Once all instances are converted,
vm_fault_t will become a distinct type.
Reference id -> 1c8f422059 ("mm: change return type to
vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new axp288 extcon driver has no dependency on USB itself but
calls the usb role switch helper functions. This causes a link error
when USB_COMMON is disabled, as that subdirectory never gets entered:
drivers/extcon/extcon-axp288.o: In function `axp288_usb_role_work':
extcon-axp288.c:(.text+0x47b): undefined reference to `usb_role_switch_set_role'
extcon-axp288.c:(.text+0x498): undefined reference to `usb_role_switch_get_role'
drivers/extcon/extcon-axp288.o: In function `axp288_extcon_probe':
extcon-axp288.c:(.text+0x675): undefined reference to `usb_role_switch_get'
extcon-axp288.c:(.text+0x6d1): undefined reference to `usb_role_switch_put'
drivers/extcon/extcon-axp288.o: In function `axp288_put_role_sw':
extcon-axp288.c:(.text+0x1c): undefined reference to `usb_role_switch_put'
There are multiple ways of fixing this, I chose to 'select USB_COMMON',
since that is how we solved the same problem for other helpers like
USB_LED_TRIG or PHY drivers.
Fixes: d54f063cdb ("extcon: axp288: Set USB role where necessary")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently hcd.c is the only consumer of the usb_phy_roothub logic. This
already includes the required header files so struct device is known.
However, future consumers might not know about struct device.
Add a forward declaration for struct device to fix potential future
consumers which don't include any of the struct device API headers.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the generic PHY support is disabled the stub of devm_of_phy_get_by_index
returns ENOSYS. This corner case isn't handled properly by
usb_phy_roothub_add_phy and at least breaks USB support on Raspberry Pi
(bcm2835_defconfig):
dwc2 20980000.usb: dwc2_hcd_init() FAILED, returning -38
dwc2: probe of 20980000.usb failed with error -38
Let usb_phy_roothub_alloc() return in case CONFIG_GENERIC_PHY is
disabled to fix this issue (compilers might even be smart enough to
optimize away most of the code within usb_phy_roothub_alloc and
usb_phy_roothub_add_phy if CONFIG_GENERIC_PHY is disabled). All
existing usb_phy_roothub_* functions are already NULL-safe, so no
special handling is required there.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the USB controller can wake up the system (which is the case for
example with the Mediatek USB3 IP) then we must not call phy_exit during
suspend to ensure that the USB controller doesn't have to re-enumerate
the devices during resume.
However, if the USB controller cannot wake up the system (which is the
case for example on various TI platforms using a dwc3 controller) then
we must call phy_exit during suspend. Otherwise the PHY driver keeps the
clocks enabled, which prevents the system from reaching the lowest power
levels in the suspend state.
Solve this by introducing two new functions in the PHY wrapper which are
dedicated to the suspend and resume handling.
If the controller can wake up the system the new usb_phy_roothub_suspend
function will simply call usb_phy_roothub_power_off. However, if wake up
is not supported by the controller it will also call
usb_phy_roothub_exit.
The also new usb_phy_roothub_resume function takes care of calling
usb_phy_roothub_init (if the controller can't wake up the system) in
addition to usb_phy_roothub_power_on.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Fixes: 178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD core")
Reported-by: Roger Quadros <rogerq@ti.com>
Suggested-by: Roger Quadros <rogerq@ti.com>
Suggested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this patch usb_phy_roothub_init served two purposes (from a
caller's point of view - like hcd.c):
- parsing the PHYs and allocating the list entries
- calling phy_init on each list entry
While this worked so far it has one disadvantage: if we need to call
phy_init for each PHY instance then the existing code cannot be re-used.
Solve this by splitting off usb_phy_roothub_alloc which only parses the
PHYs and allocates the list entries.
usb_phy_roothub_init then gets a struct usb_phy_roothub and only calls
phy_init on each PHY instance (along with the corresponding cleanup if
that failed somewhere).
This is a preparation step for adding proper suspend support for some
hardware that requires phy_exit to be called during suspend and phy_init
to be called during resume.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_phy_roothub_exit() should return the error code from the phy_exit()
call if exiting the PHY failed.
However, since a wrong variable is used usb_phy_roothub_exit() currently
always returns 0, even if one of the phy_exit calls returned an error.
Clang also reports this bug:
kernel/drivers/usb/core/phy.c:114:8: warning: explicitly assigning value of
variable of type 'int' to itself [-Wself-assign] error, forbidden
warning: phy.c:114
Fix this by assigning the error code from phy_exit() to the "ret"
variable to propagate the error correctly.
Fixes: 07dbff0ddb ("usb: core: add a wrapper for the USB PHYs on the HCD")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rishabh Bhatnagar <rishabhb@codeaurora.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some boards, under heavy load, the EC firmware is
unable to complete commands even in one second. Increasing
the command completion timeout value to five seconds.
Reported-by: Quanxian Wang <quanxian.wang@intel.com>
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b07c12517f
It is incomplete and causes hangs on devices when shutting down. It
needs a much more "complete" fix in order to work properly. As that fix
has not been merged, revert this patch for now before it causes any more
problems.
Cc: Greg Hackmann <ghackmann@google.com>
Cc: Adam Wallis <awallis@codeaurora.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DELAY_INIT quirk to fix the following problem with HP
v222w 16GB Mini:
usb 1-3: unable to read config index 0 descriptor/start: -110
usb 1-3: can't read configurations, error -110
usb 1-3: can't set config #1, error -110
Signed-off-by: Kamil Lulko <kamilx.lulko@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is the following build error with CONFIG_TYPEC_UCSI=m, CONFIG_FTRACE=y
and CONFIG_TRACING=n:
ERROR: "__tracepoint_ucsi_command" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_register_port" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_notify" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_reset_ppm" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_run_command" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_ack" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
ERROR: "__tracepoint_ucsi_connector_change" [drivers/usb/typec/ucsi/typec_ucsi.ko] undefined!
This compination is quite hard to create because CONFIG_TRACING gets selected
only in rare cases without CONFIG_FTRACE.
The build failure is caused by conditionally compiling trace.c depending on
the wrong option CONFIG_FTRACE. Change this to depend on CONFIG_TRACING like
other users of tracepoints do.
Fixes: c1b0bc2dab ("usb: typec: Add support for UCSI interface")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix it to not print kernel pointer address. Remove the conditional
and debug message as it isn't very useful.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vhci_hcd fails to do reset to put usb device and sockfd in the
module remove/stop paths. Fix the leak.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.
Resume condition is reported differently on USB 2.0 and USB 3.0 devices.
On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.
On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Armada 7K/8K we need to explicitly enable the register clock. This
clock is optional because not all the SoCs using this IP need it but at
least for Armada 7K/8K it is actually mandatory.
The change was done at xhci-plat level and not at a xhci-mvebu.c because,
it is expected that other SoC would have this kind of constraint.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Dell Inspiron 5775 is a Raven Ridge. The Enable Slot command timed
out when a USB device gets plugged:
[ 212.156326] xhci_hcd 0000:03:00.3: Error while assigning device slot ID
[ 212.156340] xhci_hcd 0000:03:00.3: Max number of devices this xHCI host supports is 64.
[ 212.156348] usb usb2-port3: couldn't allocate usb_device
AMD suggests that a delay before xHC suspends can fix the issue.
I can confirm it fixes the issue, so use the suspend delay quirk for
Raven Ridge's xHC.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
