[why]
Currently logical values are swapped in HW, causing
system aperture to be undefined, so VA and PA cannot co-exist
[how]
program values correctly
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
'second_line_offset_adj' was mistakenly left at zero, even though DSC spec
v1.2a recommends setting this field to 512 for 4:2:0.
[how]
Set 'second_line_offset_adj' to 512 for 4:2:0 and leave at zero otherwise
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We're not expected to enter the default case, but not returning a
default value here is incorrect.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unintentionally introduced behaviour change from previous refactor,
which causes clks to be 0 in no stream cases, which will cause
divide by 0.
[How]
Skip calculation of clocks when no stream. Which is the same as old
behaviour.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <tong.cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some parts of the DSC spec relating to 4.2.0 were not reflected in
drm_dsc_compute_rc_parameters, causing unexpected config failures
[How]
Add nsl_bpg_offset and rbs_min computation
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dce was re-arch'd, therefore adding aux tracing log into new dce
[How]
The porting from submit_channel_request/process_channel_reply of aux_engine_dce110.c
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <tong.cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.
[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching
[how]
Use existing override logic. If override not defined, then force
min = 507
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For better readability and reusability
[How]
Move snippets of BW calculation code into helpers.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A regression caused dsc to never get disabled in certain situations.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some values were not being converted or bit-shifted properly for
HW registers, causing black screen
[how]
Fix up the values before programming HW
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To add support for OS requirement to set preferred link training
parameters.
[HOW]
Create new structure of dp link training overrides. During link training
processes, these values should be used instead of the default training
parameters.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On some modes SMU will be in infinite loop state at boot, this is
because driver assumes p_state_support is false, but this is the
opposite of the assumed boot state by SMU. we optimize away
notifying SMU about no pstate, and so they will get stuck
[how]
when we init clk manager, init pstate to true, so it matches driver load
assumption
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
not needed for navi14 at the moment.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change the pipes to 5 if the asic is nv14
This is a temp patch, there was some refactor in the dml part of the code.
which is not in this branch. for now this is good, we can implement this
properly once we have an updated branch.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
Some active dongles have DP++ port and DP port at the same time. Current
code doesn't cover DP++ case and processes as default DVI case, in which
audio is disabled. Because of dual mode, DP case is also treat as DVI case
for the other port.
[How]:
According DP 1.4 spec, add DP++ procedure similar with HDMI case. Also
add None dongle type for DP case.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously assume eDP sink present if connector present. Do not
need to enforce this restriction. Fix issue where driver attempt
to read link setting even though no edp connected.
{How]
Only read link setting after reading connection status.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES)
but the max number of audio devices (num_audio) is 7. In some projects,
it will run out of audios array.
[How]
Incraese the audios array size to 7.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For boards that support eDP but do not have a physical eDP
display connected an ASSERT will be thrown. This is not a
critical failure and shouldn't be treated as such.
[How]
Drop the assertion.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dm_helpers_parse_edid_caps, there is a corner case where no speakers
can be allocated even though the audio mode count is greater than 0.
Enabling audio when no speaker allocations exists can cause issues in
the video stream.
[How]
Add a check to not enable audio unless one or more speaker allocations
exist (since doing this can cause issues in the video stream).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is possible (but very unlikely) that constructing dc fails
before current_state is created.
We support 666 color depth in some scenarios, but this
isn't handled in get_norm_pix_clk. It uses exactly the
same pixel clock as the 888 case.
[How]
Check for non null current_state before destructing.
Add case for 666 color depth to get_norm_pix_clk to
avoid assertion.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver will create 0, 1, and 2 ddc engines for RV2,
but some platforms used 0, 1, and 3.
[How]
Still allocate 4 ddc engines for RV2.
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot optimization removed proper front end power off sequence.
In driver disable enable case, this causes driver to power gate hubp
and dpp while there is still memory fetching going on, this can cause
invalid memory requests to be generated which will hang data fabric.
[How]
Put back proper front end power off sequence
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In pipe split issue occurs when we program immediate flip while vsync flip is pending
[how]
Don't program immediate flip until flip is no longer pending
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display's hsync width is lower than the minimum dcn20 is set
to support right now. This will cause optc1_validate_timing to fail which
eventually will result in wrong set mode. This was set to 8 as per
HW team's request for no valid reason.
[How]
Changing min_h_sync_width to 4 will let us validate timing for
preffered mode and light up the headset. This change was made
to Vega 10 before for a similar issue.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some platforms, the encoder id 3 is not populated. So the encoders
are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This
would cause encoders id 4 & id 5 to fail when finding corresponding
audio device, defaulting to the first available audio device. As result,
we cannot stream audio into two DP ports with encoders id 4 & id 5.
[How]
It need to create enough audio device objects (0 - 5) to perform matching.
Then use encoder engine id to find matched audio device.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When the system is going into suspend, set_backlight gets called
after the eDP got blanked. Since smooth brightness is enabled,
the driver will make a call into the DMCU to ramp the brightness.
The DMCU would try to enable ABM to do so. But since the display is
blanked, this ends up causing ABM1_ACE_DBUF_REG_UPDATE_PENDING to
get stuck at 1, which results in a dead lock in the DMCU firmware.
[how]
Disable brightness ramping when the eDP display is blanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we recover from hang, we do not want to skip the audio enable call.
[How]
Disable audio in dc_reinitialize_hardware
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When launch D10.2, driver will write DPCD 0x107 with 0x00
[How]
Read MAX_DOWNSPREAD (0x0003h) then keep in current
link settings
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before accessing it's vtable, check that stream_encoder is non-null.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently we don't wait for blacklight programming completion in DMCU
when setting backlight level. Some sequences such as PSR static screen
event trigger reprogramming requires it to be complete.
[How]
Add generic wait for dmcu command completion in set backlight level.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardware docs state that we must wait until the GPUVM context is ready
after programming it.
[How]
Poll until the valid bit of PAGE_TABLE_BASE_ADDR_LO32 is set to 1 after
programming it.
v2: fix include for udelay (Alex)
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current code will not wait for the entire frame
after global unlock.
This causes dsc dynamic target bpp update corruption when
there is a surface update immediately happens after this.
[how]
Wait for the entire whole frame after unlock before continuing
the rest of stream and surface update.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DCE110, DCE112 and DCE120 the max_clks_by_state for the clk_mgr are
copied from their respective table before the call to
dce_clk_mgr_construct, but then dce_clk_mgr_construct overwrites
these with the dce80_max_clks_by_state.
[How]
Copy these after we call dce_clk_mgr_construct so we're using the
right tables.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We reset the optimized_required in atomic_plane_disable
flag immediately after it is set in atomic_plane_disconnect, causing us to
never have flag set during next flip in UpdatePlanes.
[how]
Optimize directly after each time plane is removed.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fixes issue when we have a display connected using a passive
dongle and then emulate over it using a DP connection at 1 x 1.62 Ghz.
System hangs because register bus returns back 0xFFFFFFFF for all
register reads after setting register DIG_BE_CNTL in
dcn10_link_encoder_connect_dig_be_to_fe(). Hang occurs later
when trying to do a register read.
[How]
At the start of the emulation, dc_link_set_preferred_link_settings()
and dp_retrain_link_dp_test() is called, even though it is connected
using a passive dongle.
Add an extra condition in dp_retrain_link_dp_test() to check for
link->dongle_max_pix_clk > 0. This is the only way we know if the
connection is using passive dongle so we don't retrain DP.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently logical values are swapped in HW, causing
system aperture to be undefined, so VA and PA cannot co-exist
[how]
program values correctly
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
'second_line_offset_adj' was mistakenly left at zero, even though DSC spec
v1.2a recommends setting this field to 512 for 4:2:0.
[how]
Set 'second_line_offset_adj' to 512 for 4:2:0 and leave at zero otherwise
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We're not expected to enter the default case, but not returning a
default value here is incorrect.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.
[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching
[how]
Use existing override logic. If override not defined, then force
min = 507
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A regression caused dsc to never get disabled in certain situations.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some values were not being converted or bit-shifted properly for
HW registers, causing black screen
[how]
Fix up the values before programming HW
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On some modes SMU will be in infinite loop state at boot, this is
because driver assumes p_state_support is false, but this is the
opposite of the assumed boot state by SMU. we optimize away
notifying SMU about no pstate, and so they will get stuck
[how]
when we init clk manager, init pstate to true, so it matches driver load
assumption
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] dc sw clock implementation of navi10 and raven are not exact the
same. dcccg, dchub reference clock initialization is done after dc calls
vbios dispcontroller_init table. for raven family, before
dispcontroller_init is called by dc, the ref clk values are referred
by sw clock implementation and program asic register using wrong
values. this causes dchub pstate error. This need provide valid ref
clk values. for navi10, since dispcontroller_init is not called,
dchubbub_global_timer_enable = 0, hubbub2_get_dchub_ref_freq will
hit aeert. this need remove hubbub2_get_dchub_ref_freq from this
location and move to dcn20_init_hw.
[HOW] for all asic, initialize dccg, dchub ref clk with data from
vbios firmware table by default. for raven asic family, use these data
from vbios, for asic which support sw dccg component, like navi10,
read ref clk by sw dccg functions and update the ref clk.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Workaround for now to avoid underflow.
The uclk switch time should really be bumped up to 404, but doing so
would expose p-state hang issues for higher bandwidth display
configurations.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang complains that 'false' is a not a pointer:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_resource.c:2428:10: error: expression which evaluates to zero treated as a null pointer constant of type 'struct pipe_ctx *' [-Werror,-Wnon-literal-null-conversion]
return false;
Changing it to 'NULL' looks like the right thing that will shut up
the warning and make it easier to read, while not changing behavior.
Fixes: 7ed4e6352c ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As previously fixed for dml in commit 4769278e5c ("amdgpu/dc/dml:
Support clang option for stack alignment") and calcs in commit
cc32ad8f55 ("amdgpu/dc/calcs: Support clang option for stack
alignment"), dcn20 uses an option that is not available with clang:
clang: error: unknown argument: '-mpreferred-stack-boundary=4'
scripts/Makefile.build:281: recipe for target 'drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_resource.o' failed
Use the same trick that we have in the other two files.
Fixes: 7ed4e6352c ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the clock is already logged, also log the voltage.
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The drm_audio_component can be used to give pin ELD notifications
directly to the sound driver. This fixes audio endpoints disappearing
due to missing unsolicited notifications.
[How]
Send the notification via the audio component whenever we enable or
disable audio state on a stream. This matches what i915 does with
their drm_audio_component and what Takashi Iwai's proposed hack for
radeon/amdpgu did.
This is a bit delayed in when the notification actually occurs, however.
We wait until after all the programming is complete rather than sending
the notification mid sequence.
Particular care is needed for the get ELD callback since it can happen
outside the locking and fencing DRM does for atomic commits.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to give pin notifications to the sound driver from DM we need
to know whether audio is enabled on a stream and what pin it's using
from DC.
[How]
Expose the instance via stream status if it's a mapped resource for
the stream. It will be -1 if there's no audio mapped.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On 32-bit architectures, dividing a 64-bit integer in the kernel
leads to a link error:
ERROR: "__udivdi3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
ERROR: "__divdi3" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
Change the two recently introduced instances to a multiply+shift
operation that is also much cheaper on 32-bit architectures.
We can do that here, since both of them are really 32-bit numbers
that change a few percent.
Fixes: bedbbe6af4 ("drm/amd/display: Move link functions from dc to dc_link")
Fixes: f18bc4e53a ("drm/amd/display: update calculated bounding box logic for NV")
Acked-by: Slava Abramov <slava.abramov@amd.com>
Tested-by: Slava Abramov <slava.abramov@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without this header, we get a compiler error in some configurations:
.../dc/dcn20/dcn20_hwseq.c: In function 'dcn20_hwss_wait_for_blank_complete':
.../dc/dcn20/dcn20_hwseq.c:1493:3: error: implicit declaration of function 'udelay' [-Werror=implicit-function-declaration]
Note: the use of udelay itself may be problematic, as can occupy
the CPU for 200ms in a busy-loop here.
Fixes: 7ed4e6352c ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Reviewed-by: Christian König <Christian.Koenig@amd.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All asics newer than vega10 use client ids, so simplify the
check.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are a couple of spelling mistakes in dm_error messages and
a comment. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The AVI infoframe is incorrectly programmed on DCN1/2 when enabling a
stream - causing the wrong pixel encoding to be used for display.
This is because the AVI infoframe is programmed before the DIG BE is
connected to the FE and turned on, so enabling the AFMT block doesn't
actually work and the registers subsequently can't be written to.
[How]
Program the infoframe *after* turning on the DIG FE. This was the
behavior previously used but it was incorrectly reverted
when adding the DCN2 HW sequencer code.
v2: Don't call update_info_frame twice
Fixes: 7ed4e6352c ("drm/amd/display: Add DCN2 HW Sequencer and Resource")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Inconsistent indentation and mixed use of brackets.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported by smatch:
amdgpu_dm.c:5637 amdgpu_dm_commit_planes() error: we previously assumed 'acrtc_state->stream' could be null
This seems to be checked for null pretty consistently elsewhere.
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to protect the comments. The DCN1_01 config
was dopped anyway. Got accidently brought back with the
navi merge.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We may need to sleep for up to 80ms
(8ms per each of up to 10 loop iterations):
/* First DPCD read after VDD ON can fail if the particular board
* does not have HPD pin wired correctly. So if DPCD read fails,
* which it should never happen, retry a few times. Target worst
* case scenario of 80 ms.
*/
Switch udelay to msleep to avoid limits on arm.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
during navi10 bring up, dwb causes system hang.
to continue debug major issue, disable dwb by
set num-dwb = 0. the hang issue is not reproduced now
by enable num-dwb =1. dc source is shared by all os.
win needs num-dwb = 1.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before for raven and navi we are calling pp_smu functions for pme
[how]
refactor a code so we will call clk_mgr's enable_pme_wa function so we
can use pme_wa for future asics. This way we don't need to worry about
different ASIC since clk_mgr already have that information
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging underflow issues it can be useful to have asserts when the
underflow initially occurs.
[How]
Read the underflow status registers after actions that have a high risk
of causing underflow and assert that no underflow occurred. If underflow
occurred, clear the bit.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently vmid is decided internally inside dc. With the introduction
of new asics we are required to coordinate vmid use with external
components.
This change converts vmid logic to a DAL module allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
dcn2 use fixed clocks and not program DPP CLK or Disp_CLK.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
value commited to by HW team is going to be higher
than pre-silicon, and will cause underflow if driver not
updated
[how]
update hardcoded value, update pstate switching logic
to fix case where with long uclk time we won't allow switch
even when we should
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for the upcoming DRM plane color management properties
we need to correct a lot of wrong behavior and assumptions made for
CRTC color management.
The documentation added by this commit in amdgpu_dm_color explains
how the HW color pipeline works and its limitations with the DRM
interface.
The current implementation does the following wrong:
- Implicit sRGB DGM when no CRTC DGM is set
- Implicit sRGB RGM when no CRTC RGM is set
- No way to specify a non-linear DGM matrix that produces correct output
- No way to specify a correct RGM when a linear DGM is used
We had workarounds for passing kms_color tests but not all of the
behavior we had wrong was covered by these tests (especially when
it comes to non-linear DGM). Testing both DGM and RGM at the same time
isn't something kms_color tests well either.
[How]
The specifics for how color management works in AMDGPU and the new
behavior can be found by reading the documentation added to
amdgpu_dm_color.c from this patch.
All of the incorrect cases from the old implementation have been
addressed for the atomic interface, but there still a few TODOs for
the legacy one.
Note: this does cause regressions for kms_color@pipe-a-ctm-* over HDMI.
The result looks correct from visual inspection but the CRC no longer
matches. For reference, the test was previously doing the following:
linear degamma -> CTM -> sRGB regamma -> RGB to YUV (709) -> ...
Now the test is doing:
linear degamma -> CTM -> linear regamma -> RGB to YUV (709) -> ...
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This is meant to make it clearer that 0xf is not a valid OPP ID, and
that code making use of OPP IDs should not accept this value.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
expose this function for future use
Implementation of DCN3 DIO Link Encoder including
dpcs register headers.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add dwb stereo caps and ver for future use
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add Alpha surface type for future use
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Existing behavior has overlapping ranges resulting in path
dependent SMU selection
[how]
Make ranges non-overlapping, resulting in non-path dependent
selection
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
According to the latest specs, the max_target bpp sink
can support is 16 bpp.
[how]
update dsc max_target_bpp to 16
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
required for new checks.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Current policy assumes virtual DPCD peer device as
an individual MST branch device with 1 input and 1 output.
However this is only true for virtual DP-to-DP peer device.
In general there are three types of virtual DP peer devices.
1. Sink peer device with virtual DPCD.
2. Virtual DP-to-DP Peer device with virtual DPCD.
3. Virtual DP-to-HDMI Protocol Converter Peer Device with
Virtual DPCD.
So we should break the assumption and handle all three types.
[how]
DP-to-DP peer device will have virtual DPCD cap upstream.
Sink peer device will have virtual DPCD on the logical port.
Dp to HDMI protocol converter peer device will have virtual DPCD
on its converter port.
For DSC capable Synaptics non VGA port we workaround by enumerating
a virutal DPCD peer device on its upstream
even if it doesn't have one.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
useful for debugging
[how]
plumb a debug option in dc
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Almost every function in DC that works with stream state expects that
the current state on the stream is the one that it should be writing
out. These functions are typically triggered by specifying a particular
stream update - but the actual contents of the stream update itself
are ignored, leaving it to the DM to actually update the stream state
itself.
The problem with doing this in DM is a matter of timing. On Linux
most of this is incorrectly done in atomic check, when we actually want
it to be done during atomic commit tail while access to DC is locked.
To give an example, a commit requesting to modify color management
state for DM could come in, be rejected, but still have modified
the actual system state for the stream since it's shared memory. The
next time color management gets programmed it'll use the rejected
color management info - which might not even still be around if it's
a custom transfer function.
So a reasonable place to perform this is within DC itself and this is
the model that's currently in use for surface updates. DC can even
compare the current system state to the incoming surface update to
determine update level, something that can't currnetly be done with the
framework for stream updates.
[How]
Duplicate the framework used for surface updates for stream updates
as well. Copy all the updates after checking the update type.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SwathWidthCThisState is expected to be an unsigned int array.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
when resetting pipes from 480p to dual-pipe 8k, modulo reg write for
video optimized rate updated one pipe without changing the other, causing
sync error
[how]
removed code from dcn2
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The output_bpp pipe parameter was assigned an incorrect value
(color depth enum), and subsequently used to overwrite
the OutputBpp parameter calculated by DML. Seems like this had no
effect except with DSC enabled, which would make DML produce
bad outputs.
[How]
Removed assignment to OutputBpp, fixed output_bpp assignment,
and properly set ForcedOutputLinkBPP instead of OutputBpp.
Also removed condition in DML that prevented forcing of
Output BPP with DSC enabled.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
VM implemenation is missing conversion from HW values in hubbub
DM not passing actual PTB during flip
[how]
add proper HW conversion from logical values
fix cases where we programmed VA even though we are in PA
plumb in PTB from DM
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes for the following:
- Incorrect pointer type (unsigned int instead of double)
- Incorrect DSC number of slices setting
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently DSC power gating is disabled by default because the power
transition doesn't happen, causing a crash on some systems
[how]
Fix the lack of power state transition and enable DSC power gating
by default.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Should do full update when display writeback is updated.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dsc adjustment is allowed via stream update sequence.
dsc enablement is only allowed via commit stream sequence.
with the current unified dsc set function, it is hard
to determine which sequence it is called by.
The solution is to decouple dsc adjustment out of enablement
sequence so we can handle them separately.
[how]
decouple dsc adjustment out of enablement.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
current DML logic uses currently trained setting for number
of dp lanes in DML calculations. this is obviously flawed since
just because 1 lane is in use doesn't mean only 1 lane can be used
this causes mode validation to fail depending on current state,
which is incorrect
[how]
DML should always assume 4 lanes are available. validation of
bandwidth is not supposed to be handled by DML, since we do
link validation without DML already
also, DML is expecting there to be a copy of the max state, this
state is removed when update_bounding_box is called to update
actual SKU clocks. fix this as well by duping last state.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN code should make as few references to DCE as possible
[HOW]
Copy DCE110 implementation of find_first_free_match_stream_enc_for_link
into DCN10
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
From DCE110 onward, we have the ability to assign DIG BE and FE
separately for any display connector type; before, we could only do this
for DP.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With DSC power gating enabled, one of the register reads times out occasionally,
causing a DSC test to fail.
[how]
Disable DSC power gating in Diags.
NOTE: This has to be reverted once the problems with DSC power gating are
resolved.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want a test pattern to show up on screen when we're blanked and have
visual confirm enabled, for debugging. Raven does this, it's a mistake that
Navi does not.
[How]
- in "blank_pixel_data", set appropriate DPG pattern for visual confirm
- refactor DPG calls out of "enable_stream_timing"
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
these enums/structs will be used more generically in the future
so moving it to dc_hw_types and dc_types
Signed-off-by: Tyler DiBattista <tyler.dibattista@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Reuse existent code path (dcn1+) and in order to do that apply de gamma
in 1D blender LUT and re use MPC OGAM.
Follow up is required.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Features that are desirable for minimizing the Global Sync Period:
DRR and lateflip
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In compute dsc bandwidth range there is an uninitialized variable
[how]
Initialize the variable to the correct value.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To send sdp message immediately from a single slot.
[How]
Modify the generic SDP message interface, and use GSP4 to send immediate
sdp message.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN2.0 LB BPP should be 48 or 16BPC and max cursor width should be 256.
Also use populate_dml_pipes as functions pointer instead of using it directly
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A regression was introduced when we set correct tile size
for the gfx9 swizzle mode. This resulted in incorrect
macro tile size.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Plane disable gets calls when we enable blank. On DCN2, we blank by using
DPG to display a black colour instead of using OTG blank. DPG runs off the
OPP clock, therefore we shouldn't disable the OPP clock when disabling the
plane. We do need to disable the OPP clock when disabling the entire pipe,
that will be addressed in a separate commit.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It looks like mpo isn't properly disabled during odm, this change is
meant to fix that.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dwb fixes.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
dcn20 has num_dwb =1 in the res cap, but not created.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GSL is being used to synchronize pipes when vsync is off but
on transition to vsync on during a mode change GSL is not
being reset correctly.
[How]
Disable GSL on any plane that is disabled.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A few of the new DSC DPCD caps were introduced by a DP 1.4a SCR in order
to give DSC branch decoders a chance to expose their maximum throughput
and maximum line width limitations.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If a set is done, DSC settings are zeroed out, leading to no DSC for the modes
that require ODM, such as 8k60.
This was a regression introduced by 5a4f26295176bbfc776c75aaf0f6dd8ccf806958.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Emulating passive dongle on USB-C port causes issue on some asics.
[How]
Check for DP_IS_USB_C flag in bios parser and propagate it to
encoder features flags. If DP_IS_USB_C flag is set and it is trying to
emulate passive dongle, then return fail.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DCHub arbiter has a mechanism to dynamically rate limit the DCHub
request stream to the fabric. If the memory controller is fully utilized
and the DCHub requestors are well ahead of their amortized schedule,
then it is safe to prevent the next winner from being committed and sent
to the fabric. The utilization of the memory controller is approximated
by ensuring that the number of outstanding requests is greater than a
threshold specified by the ARB_MIN_REQ_OUTSTANDING. To determine that
the DCHub requestors are well ahead of the amortized schedule, the slack
of the next winner is compared with the ARB_SAT_LEVEL in DLG RefClk
cycles.
[How]
The recommended settings to enable thise dynamic limiting for Navi is
180 requests.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It was missing, although defined in DP spec
[how]
- Add handling of this value to DSC code
- Also remove unused file dsc_helpers.c
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
This is for DC_I2c arbitration use between HW use/SW use and DMCU use.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
'Divide by zero' error happens when line size happens to be zero.
[how]
The code that makes sure line size minimum value can be 1 was already
present in DCN1 part of the driver, this is mearly a port to DCN2.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to ensure that incoming flips are latched and
complete immediately, we need to program the vupdate
interrupt to come during the back porch of each frame.
[How]
Program the vupdate start_line to be in the back porch
like it's done for DCN1.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The split condition is broken and will always activate
at the moment.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Different HW will need to init HUBP differently. For now, add a vtable
entry, and hook a NO-OP for DCN1 and DCN2.
In addition, future HW will need to access the HUBPREQ_DEBUG and
CUR_TTU_CNTL0 register for hubp_init. Add that here.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OPTC data format was left at its default value (444) when enabling
ODM combine. This caused issues with FPGA capture.
[How]
Write the OPTC_DATA_FORMAT field when enabling ODM combine.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to the generic introduction of seamless boot, the display is no
longer blanked upon boot. However, this causes corruption on some
systems that does not lock the memory in the non-secure boot case,
resulting in brief corruption on boot due to garbage being written into
the frame buffer.
[How]
Add a flag, read during DC init, to determine whether display should be
blanked on boot. Default to true.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DSC target bpp precision is a decoder DPCD and an AMD encoder capability.
It must be taken into account when calculating target bitrate.
[how]
Add a DC DSC function that does this calculation.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ABM is currently not enabled on DCN2.
[How]
Update the register name list for DCN2 and un-comment the code that
creates the abm object.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current policy will always enable DSC to 12 bpp
regardless of if the current bandwidth is enough for MST displays.
This logic is not optimal because user will get lower quality output
if DSC compression is enabled.
This change to is to implement a DSC MST bandwidth fair share
algorithm so we will dynamically decide if DSC is needed and what
quality (target bpp) is needed to fairly destribute the MST bandwidth
in one MST topology. This will allow user to see the most optimal
image quality with the given bandwidth.
[how]
We will start with lowest bandwidth possible and run a
Max-Min fairness algorithm to fairly distribute the available
bandwidth. If there is still remaining bandwidth, we will try to fit
the timing without DSC compression.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There are ASICs that have fewer DSC engines than pipes, which makes
DSC a resource that should be used only if required.
[how]
Acquire DSC HW resource if required by stream and release when not
required anymore.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] system crash when initialize dwb
current linux driver does not support dwb.
disable this feature for now.
[HOW] set num_dwb = 0 to disable dwb for now
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] linux upstream already has interrupt vupdate for freesync
in dcn10. dcn20 interrupt shares the same source code as dcn10.
but dcn20 interrupt translator does not add vupdate interrupt.
this cause index of vupdate aarray be negative which causes
crash.
[HOW] add vupdate into dc interrupt transltor
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DSC resource has to be acquired before it can be used and simply copying
a reference to it is very likely to cause problems when accessing DSC.
[how]
Set DSC resource pointer to NULL to mark it as unused after primary pipe
resources were copied to the secondary ODM pipe.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some nightly tests are failing since the new value for fclk is a
bit too low. Also, a new test for the maximum downscale case was
needed.
[How]
Updated the default value for fclk to be 1.2GHz.
Signed-off-by: Tyler DiBattista <tyler.dibattista@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
when an update programming sequence requires both
front end and back end pipe to be updated synchronously,
a global update lock needs to be set to ensure that
we don't get a frame with only front end update but
not the back end update.
[how]
setup global lock parameters on enable_stream_timing.
enable global lock when pipe_control_lock_global is called.
disable global lock when pipe_control_lock is called.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some register fields are not needed.
[How]
remove them
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We used this change to investigate the performance of bandwidth validation,
it will be useful to have if we need to investigate further.
[How]
We use performance counter tick numbers to profile performance, they live
at dc->debug.bw_val_profile (set .enable in debugger to turn on measuring).
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can split validation into three parts: getting voltage level, getting
watermarks, and rq/dlg calculations. The voltage level is enough to answer
the question "do we support this state", and the rest of it is to determine
what hardware programming is needed to support the state. Most of the calls
to validate_bandwidth only care about the first part, so we added an early
return in that case
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
display_mode_vba is for DCN2 and up. When building for upstream (DCN1
enabled only), there will be a build error, since display_mode_vba.c/h
is stripped out.
Note that building DCN1 only with internal dal-dev is still fine, since
display_mode_vba.h is not stripped out internally - only in upstream.
The make directives therefore stll work, and so will any #include's.
[How]
Since subsequent generations require DCN2 enabled anyways, guard the
makefile directive for display_mode_vba.o with DCN2. Guard any includes
with DCN2. In addition, guard the entire contents of display_mode_vba.h
with DCN2, to simulate the file being stripped out in upstream.
A forward declaration for 'struct display_mode_lib' also needs to be
added in display_mode_lib.h. Previously, display_mode_vba.h contained
the forward declaration, and display_mode_lib.h in turn included it.
This won't work if mode_vba.h is stripped out, requring mode_lib.h to do
so itself.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Usage of this enum is DSC-only.
[How]
Guard it with CONFIG_DRM_AMD_DC_DSC_SUPPORT.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Can not turn on two displays at the same time with the asic having only one DSC.
DC_DSC_RESOURCE allocation failed.
[Solution]
Only add_dsc if the timing is dsc capable based on diag_dc and num_dsc
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If voltage level > 0, DCFCLK and SOCCLK could be 0 during DML
calculations, which ended up causing an assert.
[How]
Initialize dcfclk_mhz and socclk_mhz values according to the
voltage level.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Added some regs and exposed some functions for future use
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On at least some of the devices (e.g. Realtek scaler) we get a black screen if 1/16th
precision is used.
[how]
Work around it by reducing precision to 1/8th for N4:2:2 and 4:2:0 color formats. This
is a safe workaround and would have a very mild impact on the quality.
The issue is still to be root-caused and fixed correctly.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Global optic double buffer lock is currently disabled due to
incorrect programming sequence that affects non global lock.
[how]
Isolate global lock programming sequence out of non global lock
programming sequence, so it can be enabled without affecting
non global lock.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
This is now done in the original link bandwidth calculation and DSC
must not do this anymore.
[how]
Remove the line of code that should have been removed when transition
to correctly applying FEC overhead was made.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We shouldnt need overhead on top of dppclk when setting fclk.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Clean up some dsc legacy functions that are
no longer needed.
[how]
remove two dsc functions in dc_dsc, use dc_bandwidth_in_kbps_from_timing
instead of calc_required_bandwidth_for_timing.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn20_apply_ctx_for_surface can be called with 0 planes, which means we
should blank the display. In this case when we get down to
dcn20_setup_gsl_group_as_lock, pipe_ctx->plane_state is NULL, but we don't
check for it. However, this function is only called by
dcn20_pipe_control_lock, and in that function we alraedy have a local for
the immediate flip status, which is what we care about in the plane state.
[How]
- pass in immediate flip status as parameter
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently dsc is validated not taking the image width limitation into
mind.
This change addresses that, but due to previous design being limited
to non odm dsc validation additional sequence changes are made.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
u clk set request was being sent in units of mts, when it needed to be
in units of Mhz
[How]
add a division by 16 to convert from mts to Mhz
Signed-off-by: Aidan Wood <Aidan.Wood@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If num_states == 0 we did update_bound_box which doesn't updated any max
clocks if num_states == 0, therefore we need to do cap_soc_clocks
instead, also SMU cannot set DCF clock to a higher than or equal to freq
than SOC clock
[How]
Add a num_states != 0 check for update_bounding_box to be run, and after
we run get_maximum_sustainable_clocks we now check if the reported max
value of DCF is higher than SOC and if necessary set it to 1000
(becomes 1 after division by 1000) lower than SOC
Signed-off-by: Aidan Wood <Aidan.Wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently link bandwidth is calculated in various places using the same
multi-step formula. Doing this in one common place makes sure the same
formula will indeed be applied to all link bandwidth calculations.
It also makes it possible to apply link-setting-specific adjustments
that affect effective link bandwidth.
[how]
Replace all implementations of link bandwidth calculation with a call
to a function.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
When TM is enabled with 3dlut, we apply conversion to
dcip3 in gamut remap matrix, if source area less than
dcip3. If it is bigger, we remap to bt2020. The added
flags will be used to facilitate this logic.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently dcn2+ validation will unconditionally print a failure
reason before validation completes. This change categorizes the
failure reason as a warning log and only prints at the end of
validation resolving false positives.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
swath_bytes_horz_wc should be 256/64/64 for 2160p 32bpp surface
Signed-off-by: Bob Yang <Bob.Yang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn*_disable_plane() doesn't unlock the pipe anymore, making the extra
lock unnecessary.
In addition - during full plane updates - all necessary pipes should be
locked/unlocked together when modifying hubp to avoid tearing in
pipesplit setups.
[How]
Remove redundant locks, and add function to lock all pipes. If an
interdependent pipe update is required, lock down all pipes. Otherwise,
lock only the top pipe for the updated pipe tree.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A previous fix was done for DCN1 that needed to be ported to DCN2:
commit 60c677534e73 ("drm/amd/display: Disconnect mpcc when changing tg")
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why] we meet a bug when program dsc register even dsc mode is not
enabled. disable dsc config for now. we will re-visit this issue.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] dcn20 enable usb-c dp ALT mode in dmcu. There is bug
when enable abm feature which cause system crash. dal team
will debug this bug later.
[HOW] disable dcn abm feature for dcn20.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pstate allow/block is not being handled properly on DCN2
[how]
DML needs to be updated to calculate pstate support at both min and max
mpc combine rather than just min
clock manager needs to update current to new pstate support before
sending to pplib/smu
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding writeback_config enum to vba_vars_st, replacing old flag.
Initialize to dm_normal.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.
[How]
- Pull get_active_display_cnt out to clk_mgr.
- Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
DMUB is using DPREF CLK, but DMCU still use displayclk.
This is for updating DMCU wait_for_loop after display clock change.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Modern Standby may toggle display adapter state between D0
and D3 state unpredictably.
But events that cause transition to D0 are not always resulting
in a display light up scenario.
Modern eDP panels should be able to power on panel logic
quickly upon VDD going high. Based on spec, the T3 time
between VDD on and HPD high can be between 0 and 80 ms.
Doing any tricky sorts of optimization by powering on panel
VDD early during D0 transition on can negatively impact other
features due to unnecessary power drain and toggling when
final system state does not intend for the panel to be lit up.
We need OEMs to source higher end panels that have T3 time
close to 0 if they want quick S3/Modern Standby resume times.
[How]
Remove panel VDD power on in init_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
link-specific functions should reside in dc_link.c
[How]
Move them there.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Current calculation of bounding box will cause DML to increase voltage
state due to DPP or DISPCLK, this is unnecessary since from DML perspective
we can max DPP/DISP can be supported at DPM0. This is because
increasing voltage for DPP/DISP is done separately via actual minimum values
of DISP and DPP CLK
[how]
For each calculated state, DPP, DISP, PHY, and DSC clk should always be set to
maximum. FCLK, SOCCLK, and DCFCLK should be based of UCLK.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. DMCU is not running on some platform but driver still send ABM
command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable
[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.
[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
caller of pp_nv_set_pme_wa_enable pass incorrect pp_smu:
dc->res_pool->pp_smu. it should be dc->res_pool->pp_smu->nv_funcs.pp_smu.
with incorrect input, pp->dm = NULL. This causes system crash.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VTG has a parameter FP2, which is defined as:
if VSTARTUP is before VSYNC:
FP2 = number of lines in between VSTARTUP and VSYNC
else
FP2 = 0
Currently, FP2 is only programmed during "program_timing". However, the
position of VSTARTUP is affected by the prefetching requirements on all pipes,
so the position might change when we do memory request control on another pipe, so we need
to make sure that FP2 stays up-to-date whenever we adjust VSTARTUP.
[How]
- refactor VTG_CONTROL programming into a new function "set_vtg_params"
- call it after calling "program_global_sync"
- make sure it's called after because it relies on the cached dlg params
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
during bring up time, before window dc-ppplib interface
design, linux dc use raven dc-pplib interface.
now nvai10 dc-pplib-smu interface is changed and verified
under window, navi10 need its specific dc-pplib-smu
interface. todo: hook set_hard_min_uclk_by_freq,
get_maximum_sustainable_clocks
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program DCN2 VMID (Virtual Memory Support)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program DCN2 cursor (IPP)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 HUBP (Display to data fabric interface
pipe) and HUBBUB (DCN memory HUB interface)
HW Blocks:
+--------++------+
| HUBBUB || HUBP |
+--------++------+
|
v
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 DPP (Multiple pipe and plane combine)
HW Blocks:
+--------+
| DPP |
+--------+
|
v
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 MPC (Multiple pipe and plane combine)
HW Blocks:
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program the DCN2 OPP (Output Plane Processing)
HW Blocks:
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for handling of clocking relevant to the DCN2 block,
including programming of the DCCG (Display Controller Clock Generator)
block:
HW Blocks:
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN2, which entails our
stream and link encoders.
HW Blocks:
+--------+
| DIO |
+--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update DML (Display Mode Lib) to support DCN2
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to program DCN2 IRQ handling
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding support to program GPIO HW block of DCN2
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding support to program DCN2 AUX and I2C HW.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN2.0 (Display Core Next) is the display block in Navi10.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We don't want to expose sensitive ASIC information before ASIC release.
[HOW]
Encode the soc_bounding_box in the gpu_info FW (for Linux) and read it
at driver load.
v2: fix warning when CONFIG_DRM_AMD_DC_DCN2_0 is not set (Alex)
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add callback function get_clock_by_type_with_latency for navi10 asic
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit ebc8c6f18322ad54275997a888ca1731d74b711f.
There are still missing corner cases with cursor interaction and these
fast plane updates on Picasso and Raven2 leading to endless PSTATE
warnings for typical desktop usage depending on the userspace.
This change should be reverted until these issues have been resolved.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110949
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After clkmgr rework it gets initialized after resource pool.
The clkmgr is used in resource pool init for xgmi path.
That causes driver crash on Vega20 with xgmi due to NULL deref.
[How]
Move xgmi compensation code to dce121_clk_mgr_construct()
That also allows to make dce121_clock_patch_xgmi_ss_info()
internal static function.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Gj1MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGctkH/0At3+SQPY2JJSy8
i6+TDeytFx9OggeGLPHChRfehkAlvMb/kd34QHnuEvDqUuCAMU6HZQJFKoK9mvFI
sDJVayPGDSqpm+iv8qLpMBPShiCXYVnGZeVfOdv36jUswL0k6wHV1pz4avFkDeZa
1F4pmI6O2XRkNTYQawbUaFkAngWUCBG9ECLnHJnuIY6ohShBvjI4+E2JUaht+8gO
M2h2b9ieddWmjxV3LTKgsK1v+347RljxdZTWnJ62SCDSEVZvsgSA9W2wnebVhBkJ
drSmrFLxNiM+W45mkbUFmQixRSmjv++oRR096fxAnodBxMw0TDxE1RiMQWE6rVvG
N6MC6xA=
=+B0P
-----END PGP SIGNATURE-----
Merge v5.2-rc5 into drm-next
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The memory was set to zero already by a call of the function “kzalloc”.
Thus remove an extra call of the function “memset” for this purpose.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
"git diff" says:
\ No newline at end of file
after modifying the file.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Add code to signal all dma-fences when freed with pending signals.
- Annotate reservation object access in CONFIG_DEBUG_MUTEXES
Core Changes:
- Assorted documentation fixes.
- Use irqsave/restore spinlock to add crc entry.
- Move code around to drm_client, for internal modeset clients.
- Make drm_crtc.h and drm_debugfs.h self-contained.
- Remove drm_fb_helper_connector.
- Add bootsplash to todo.
- Fix lock ordering in pan_display_legacy.
- Support pinning buffers to current location in gem-vram.
- Remove the now unused locking functions from gem-vram.
- Remove the now unused kmap-object argument from vram helpers.
- Stop checking return value of debugfs_create.
- Add atomic encoder enable/disable helpers.
- pass drm_atomic_state to atomic connector check.
- Add atomic support for bridge enable/disable.
- Add self refresh helpers to core.
Driver Changes:
- Add extra delay to make MTP SDM845 work.
- Small fixes to virtio, vkms, sii902x, sii9234, ast, mcde, analogix, rockchip.
- Add zpos and ?BGR8888 support to meson.
- More removals of drm_os_linux and drmP headers for amd, radeon, sti, r128, r128, savage, sis.
- Allow synopsis to unwedge the i2c hdmi bus.
- Add orientation quirks for GPD panels.
- Edid cleanups and fixing handling for edid < 1.2.
- Add runtime pm to stm.
- Handle s/r in dw-hdmi.
- Add hooks for power on/off to dsi for stm.
- Remove virtio dirty tracking code, done in drm core.
- Rework BO handling in ast and mgag200.
-----BEGIN PGP SIGNATURE-----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=4uQX
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add code to signal all dma-fences when freed with pending signals.
- Annotate reservation object access in CONFIG_DEBUG_MUTEXES
Core Changes:
- Assorted documentation fixes.
- Use irqsave/restore spinlock to add crc entry.
- Move code around to drm_client, for internal modeset clients.
- Make drm_crtc.h and drm_debugfs.h self-contained.
- Remove drm_fb_helper_connector.
- Add bootsplash to todo.
- Fix lock ordering in pan_display_legacy.
- Support pinning buffers to current location in gem-vram.
- Remove the now unused locking functions from gem-vram.
- Remove the now unused kmap-object argument from vram helpers.
- Stop checking return value of debugfs_create.
- Add atomic encoder enable/disable helpers.
- pass drm_atomic_state to atomic connector check.
- Add atomic support for bridge enable/disable.
- Add self refresh helpers to core.
Driver Changes:
- Add extra delay to make MTP SDM845 work.
- Small fixes to virtio, vkms, sii902x, sii9234, ast, mcde, analogix, rockchip.
- Add zpos and ?BGR8888 support to meson.
- More removals of drm_os_linux and drmP headers for amd, radeon, sti, r128, r128, savage, sis.
- Allow synopsis to unwedge the i2c hdmi bus.
- Add orientation quirks for GPD panels.
- Edid cleanups and fixing handling for edid < 1.2.
- Add runtime pm to stm.
- Handle s/r in dw-hdmi.
- Add hooks for power on/off to dsi for stm.
- Remove virtio dirty tracking code, done in drm core.
- Rework BO handling in ast and mgag200.
Tiny conflict in drivers/gpu/drm/amd/display/dc/clk_mgr/clk_mgr.c,
needed #include <linux/slab.h> to make it compile.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0e01de30-9797-853c-732f-4a5bd6e61445@linux.intel.com
I missed amdgpu in my connnector_helper_funcs->atomic_check conversion,
which is understandably causing compilation failures.
Fixes: 6f3b62781b ("drm: Convert connector_helper_funcs->atomic_check to accept drm_atomic_state")
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> [for rcar lvds]
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Karol Herbst <karolherbst@gmail.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: dri-devel@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190614002713.141340-1-sean@poorly.run
this patch fixes below compilation error
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c: In
function ‘dcn10_apply_ctx_for_surface’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:2378:3:
error: implicit declaration of function ‘udelay’
[-Werror=implicit-function-declaration]
udelay(underflow_check_delay_us);
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: David Francis <David.Francis@amd.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: hersen wu <hersenxs.wu@amd.com>
Cc: "Leo (Hanghong) Ma" <hanghong.ma@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Found issue in EDID Emulation where if we connect a display using
a passive HDMI-DP dongle, disconnect it and then try to emulate
a display using DP, we could not see 4K modes. This was because
on a disconnect, dongle_max_pix_clk was still set so when we
emulate using DP, in dc_link_validate_mode_timing(), it would
think we were still using a dongle and limit the modes we support.
[How]
In dc_link_detect(), set dongle_max_pix_clk to 0 when we detect
a hotplug out ( if new_connection_type = dc_connection_none ).
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
refactor a code so we will call clk_mgr's enable_pme_wa function so we
can use pme_wa for future asics. This way we don't need to worry about
different ASIC since clk_mgr already have that information
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
The spec does not allow POST_LT_ADJ_GRANTED to be set when TPS4 is used.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We incorrectly began powering down the display at boot/resume whenever
fast boot was not possible. This should not be done in the case where there
exists a stream for the eDP since this implies that we want to turn it on.
[How]
Add check for eDP stream to decide whether to power off edp.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
By the time output csc matrix is being programmed, stream connection to
OPP has been established, but this information has not been relayed back
to HUBP.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Our existing logic in deciding whether to use RAM or ROM
depends on whether we are dealing with an identity gamma ramp.
[How]
In addition to the is_identity flag
a new is_logical_identity flag has been
added. The is_identity flag now denotes
whether the OS gamma is an RGB256 identity
and the new logical identity will inidicate
that the given gamma ramp regardless of its
type is identity.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For debugging underflow issues it can be useful to have asserts when the
underflow initially occurs.
[How]
Read the underflow status registers after actions that have a high risk
of causing underflow and assert that no underflow occurred. If underflow
occurred, clear the bit.
Signed-off-by: Thomas Lim <Thomas.Lim@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently vmid is decided internally inside dc. This makes it
difficult to use vmid use with external components.
This change moves vmid logic outside dc and allowing vmid to be
passed in as a parameter to DC.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBios sometimes reports incorrect object type as encoder instead of
connector
[How]
Change error message to debug message
Signed-off-by: Jordan Lazare <Jordan.Lazare@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are no longer needed, Also added RESERVED bits.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using this logic breaks driver unload, this is a temporary fix
a followup patch will properly fix this
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD not going to be high if Panel VDD is off
And all AUX transaction will fail :(
[How]
1. Power on VDD before attempting detection if it isn't already on
2. Improve the robustness by having a retry mechanism on the
first DPCD read after VDD on. If a particular board always holds
HPD high incorrectly, the AUX access may fail, so we can retry
in those scenarios. This change would only improve logic
since it prevents AUX failure leading to bad resolution on internal
panel.
3. We should never need to re-detect internal panel, so logic
is re-arranged a bit to skip earlier.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for the upcoming DRM plane color management properties
we need to correct a lot of wrong behavior and assumptions made for
CRTC color management.
The documentation added by this commit in amdgpu_dm_color explains
how the HW color pipeline works and its limitations with the DRM
interface.
The current implementation does the following wrong:
- Implicit sRGB DGM when no CRTC DGM is set
- Implicit sRGB RGM when no CRTC RGM is set
- No way to specify a non-linear DGM matrix that produces correct output
- No way to specify a correct RGM when a linear DGM is used
We had workarounds for passing kms_color tests but not all of the
behavior we had wrong was covered by these tests (especially when
it comes to non-linear DGM). Testing both DGM and RGM at the same time
isn't something kms_color tests well either.
[How]
The specifics for how color management works in AMDGPU and the new
behavior can be found by reading the documentation added to
amdgpu_dm_color.c from this patch.
All of the incorrect cases from the old implementation have been
addressed for the atomic interface, but there still a few TODOs for
the legacy one.
Note: this does cause regressions for kms_color@pipe-a-ctm-* over HDMI.
The result looks correct from visual inspection but the CRC no longer
matches. For reference, the test was previously doing the following:
linear degamma -> CTM -> sRGB regamma -> RGB to YUV (709) -> ...
Now the test is doing:
linear degamma -> CTM -> linear regamma -> RGB to YUV (709) -> ...
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
This is meant to make it clearer that 0xf is not a valid OPP ID, and
that code making use of OPP IDs should not accept this value.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Add i2c_hw_Status check to make sure when HW i2c is in use.
2. Don't reset HW engine in is_hw_busy() and instead do this in
process_transaction() because SW i2c does not check if hw i2c is in use
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to assert just return
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Almost every function in DC that works with stream state expects that
the current state on the stream is the one that it should be writing
out. These functions are typically triggered by specifying a particular
stream update - but the actual contents of the stream update itself
are ignored, leaving it to the DM to actually update the stream state
itself.
The problem with doing this in DM is a matter of timing. On Linux
most of this is incorrectly done in atomic check, when we actually want
it to be done during atomic commit tail while access to DC is locked.
To give an example, a commit requesting to modify color management
state for DM could come in, be rejected, but still have modified
the actual system state for the stream since it's shared memory. The
next time color management gets programmed it'll use the rejected
color management info - which might not even still be around if it's
a custom transfer function.
So a reasonable place to perform this is within DC itself and this is
the model that's currently in use for surface updates. DC can even
compare the current system state to the incoming surface update to
determine update level, something that can't currnetly be done with the
framework for stream updates.
[How]
Duplicate the framework used for surface updates for stream updates
as well. Copy all the updates after checking the update type.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some panels return a link rate of 0 (unknown) in DPCD 0. In this case,
an appropriate mode cannot be set, and certain panels will show
corruption as they are forced to use a mode they do not support.
[HOW]
Read DPCD 10 in the case where supported link rate from DPCD 0 is
unknown, and pass that value on to the reported link rate.
This re-introduces behaviour present in previous versions that appears
to have been accidentally removed.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tao.Huang <Tao.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The module parameter to specify the default ABM level is now defined,
so hook it up in DM.
[How]
On connector reset specify the default level. DC will program this as
part of the modeset since it gets passed onto the stream in
dm_update_crtc_state.
It's only set for eDP connectors, but it doesn't matter if this is
specified for connectors or hardware that doesn't support ABM.
It's DC's responsibility to check that ABM can be set or adjusted, and
DC does check that the DMCU firmware is running and if there's backlight
control available.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever the a modeset is allowed (but not neccessarily required) we
currently recreate all the planes in the state. Most IGT tests and
legacy IOCTLs create atomic commits with this flag set, so the pipes
are often unnecessarily reprogrammed.
Poor performance and stuttering can occur when many of these commits
are frequently issued.
This flag was needed when the appropriate conditions for checking
whether the planes needed a reset were not in place, but
should_reset_plane should cover everything needed now.
[How]
Drop the check for state->allow_modeset in should_reset_plane.
All planes on a CRTC should reset in the following conditions:
- The CRTC needs a modeset
- The CRTC degamma changes
- Planes are added or removed to the CRTC
These conditions are all covered in should_reset_plane.
We still can't drop the format change check in should_reset_plane since
fill_dc_plane_info_and_addr isn't called when validating the state, so
we can't tell if a FULL update is needed or not.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <david.francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The old logic for checking which output depth to use relied on using
the current connector state rather than the new proposed state. This
was a problem when performing atomic commits since we weren't verifying
it against the incoming max_requested_bpc.
But switching this to only use the new state and not the current state
breaks filtering modes - it'll always assume that the maximum bpc
supported by the display is in use, which will cause certain modes
like 1440p@144Hz to be filtered even when using 8bpc.
[How]
Still use the connector->state if we aren't passed an explicit state.
This will respect the max_bpc the user currently has when filtering
modes.
Also remember to reset the default max_requested_bpc to 8 whenever
connector reset is called to retain old behavior when using the new
property.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110845
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unlike our regular connectors, MST connectors don't start off with
an initial connector state. This causes a NULL pointer dereference to
occur when attaching the bpc property since it tries to modify the
connector state.
We need an initial connector state on the connector to avoid the crash.
[How]
Use our reset helper to allocate an initial state and reset the values
to their defaults. We were already doing this before, just not for
MST connectors.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This will be useful for verifying whether we enter the correct output
color depth from IGT.
[How]
Locks the connector and associated CRTC if available and outputs
the current and maximum output bpc values.
Example:
cat /sys/kernel/debug/dri/0/DP-1/output_bpc
Current: 8
Maximum: 10
v2: Drop unneeded connector status check
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN_VERSION_1_01 is no longer handled in the dal_hw_translate_init
switch since it was inadvertently dropped in the patch that removed the
unnecessary DCN1_01 guards.
This caused numerous regressions on DCN1_01 when loading the driver.
[How]
Add it back.
Fixes: 97df424fe7 ("drm/amd/display: Drop DCN1_01 guards")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching from vt to desktop with EDID emulation we can receive
an atomic commit such that we have a crtc where mode_changed = true.
During the dm_update_crtc_state disable pass we remove the stream from
the context and free it on the dm_new_crtc_state.
During the enable pass we compare the new provisional stream to the
dm_old_crtc_state->stream and determine that the stream is unchanged
and no scaling has been changed.
Following this, new_crtc_state->mode_changed is then set to false.
The connectors haven't changed and the CRTC active state hasn't changed
so drm_atomic_crtc_needs_modeset returns false, so we jump to
skip_modeset and we hit:
BUG_ON(dm_new_crtc_state->stream == NULL);
...since the old stream is gone from the context and the new stream is
also still NULL.
[How]
Ensure that we still a stream to reuse before checking if we can reuse
the old stream without a full modeset.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Drop all uses of drmP.h in drm/amd/display/.
Fix fallout.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-9-sam@ravnborg.org
Drop use of the deprecated drmP.h header file from
all amd header files.
This makes it a more smooth process to get rid of drmP.h
in the .c files.
Added include files and forwards as appropriate.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-7-sam@ravnborg.org
Drop use of the deprecated drmP.h header from atom.h
Fix fallout in various files.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-6-sam@ravnborg.org
Delete the unused drmP.h from amdgpu.h.
Fix fallout in various files.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-5-sam@ravnborg.org
Drop use of the deprecated drmP.h from display/dc/os_types.h
Fix all fallout after this change.
Most of the fixes was adding a missing include of vmalloc.h.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-4-sam@ravnborg.org
Fix so no files in drm/amd/ depends on the
deprecated drm_os_linux.h header file.
It was done manually:
- remove drm_os_linux.h from drmP.h
- fix all build errros
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190609220757.10862-3-sam@ravnborg.org
amdgpu:
- Revert timeline support until KHR is ready
- Various driver reload fixes
- Refactor clock handling in DC
- Aux fixes for DC
- Bandwidth calculation updates for DC
- Fix documentation due to file rename
- RAS fix
- Fix race in late_init
ttm:
- Allow for better forward progress when there is heavy memory contention
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190606032537.6939-1-alexander.deucher@amd.com
These got added back by subsequent merges accidently.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEuXvWqAysSYEJGuVH/lWMcqZwE8MFAlz3iIMACgkQ/lWMcqZw
E8NlwA/+NxCaUyuymD7dxw266Y4HlsL+jcba1pYOjuMpknnhb4HgDEgg//UekjSN
UxskzNh4H4+DD4yphgsFn5wqkivlUxTFS+mt0FdrjT8h2gij4jQQ1k8EIMeuxg5P
OHjJYwvHN2c/4fiQF9Fo5/nxYciN0erzcA7mFcbMeDIWtyO7BBr/6eXKl68G9FwH
cXvpshNzVNvvpoaSpZLnxm/YkLDZNj1Io0+sVu2/w0AY0jmGEFFFpXxh42nnh4TL
CwLzilfstJnXmJuM5nwcpUS1pV9IovauVDD3owGL5J1ZwiFy8j+e9GAA4kv6pf8C
VsK3FynFt7u1BX26yfLWVLbCFF8wrpz5B3WZXrJLGiSpQi3zshpc/CMnchLfOdYf
FijrQTrciVsQglxrDqqtaJ54ReF7wr5LWW3PhB1GYZRbQb9pZ4h4zroQQToFSkBa
uxAEj9khJWgLhY6CeYzVbT1kShqjG7vjskDUbw493tZ+VqvL04Cy47npYi28iYxu
hl+5maJY5KWnO6YTeJbuox3GjWelURtGhqfxbWhRAn1h74UQNjG8U9x5fWf3f4v7
YgZn4Z2UvHrs5XQdZE9sZm01vKFtQM7IHqfM5l2ZkKmKY/SQ1fII/XISOoaoLIZl
X35WwB727OS4vTSCusd5QGKESh0WFtUB8dFM/NfXNQM7SGXtG/c=
=GrAP
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add devicetree bindings for new panels.
- Convert allwinner's DT bindings to a schema.
- Drop video/hdmi static functions from kernel docs.
- Discard old fence when reserving space in reservation_object_get_fences_rcu.
Core Changes:
- Add missing -ENOMEM handling in edid loading.
- Fix null pointer deref in scheduler.
- Header cleanups, making them self-contained.
- Remove drmP.h inclusion from core.
- Fix make htmldocs warning in scheduler and HDR metadata.
- Fix a few warnings in the uapi header and add a doc section for it.
- Small MST sideband error handling fix.
- Clarify userspace review requirements.
- Clarify implicit/explicit fencing in docs.
- Flush output polling on shutdown.
Driver Changes:
- Small cleanups to stm.
- Add new driver for ST-Ericsson MCDE
- Kconfig fix for meson HDMI.
- Add support for Armadeus ST0700 Adapt panel.
- Add KOE tx14d24vm1bpa panel.
- Update timings for st7701.
- Fix compile error in mcde.
- Big series of tc358767 fixes, and enabling support for IRQ and HPD handling.
- Assorted fixes to sii902x, and implementing HDMI audio support.
- Enable HDR metadata support on amdgpu.
- Assorted fixes to atmel-hlcdc, and add sam9x60 LCD controller support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6c43ffa9-11ff-5354-d772-c20fd4d1e3d9@linux.intel.com
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Calling drm_atomic_set_fb_for_plane() (which gets a reference of the new
fb and put the old fb) is not required, as it's taken care by
drm_mode_cursor_universal() when calling drm_atomic_helper_update_plane().
Cc: <stable@vger.kernel.org> # v4.20+
Fixes: 674e78acae ("drm/amd/display: Add fast path for cursor plane updates")
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-3-helen.koike@collabora.com
[Why]
We can issue HDR static metadata as part of stream updates for
non-modesets as long as we force a modeset when entering or exiting HDR.
This avoids unnecessary blanking for simple metadata updates.
[How]
When changing scaling and abm for the stream also check if HDR has
changed and send the stream update. This will only happen in non-modeset
cases.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-3-nicholas.kazlauskas@amd.com
[Why]
For userspace to send static HDR metadata to the display we need to
attach the property on the connector and send it to DC.
[How]
The property is attached to HDMI and DP connectors. Since the metadata
isn't actually available when creating the connector this isn't a
property we can dynamically support based on the extension block
being available or not.
When the HDR metadata is changed a modeset will be forced for now.
We need to switch from 8bpc to 10bpc in most cases anyway, and we want
to fully exit HDR mode when userspace gives us a NULL metadata, so this
isn't completely unnecessary.
The requirement can later be reduced to just entering and exiting HDR
or switching max bpc.
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-2-nicholas.kazlauskas@amd.com
add ticket for display bo, so that it can preempt busy bo.
v2: fix stupid rebase error
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Pierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Issue:
Will have follow error when reload driver:
[ 3986.567739] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:07.0/drm_dp_aux_dev'
[ 3986.567743] CPU: 6 PID: 1767 Comm: modprobe Tainted: G OE 5.0.0-rc1-custom #1
[ 3986.567745] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 3986.567746] Call Trace:
......
[ 3986.567808] drm_dp_aux_register_devnode+0xdc/0x140 [drm_kms_helper]
......
[ 3986.569081] kobject_add_internal failed for drm_dp_aux_dev with -EEXIST, don't try to register things with the same name in the same directory.
Reproduce sequences:
1.modprobe amdgpu
2.modprobe -r amdgpu
3.modprobe amdgpu
Root cause:
When unload driver, it doesn't unregister aux.
v2: Don't use has_aux
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We only want to manual trigger end-of-frame when the bottom-most
pipe is flipped to prevent overlays from ending the frame too early.
[How]
Check that the manual trigger is only firing on bottom plane.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There's some unnecessary mem allocation for CS_TFM_ID. What's worse, it
depends on LUT size and since it's 4K for CS_TFM_1D, it is 16x bigger
than in regular case when it's actually needed. This leads to some
crashes in stress conditions.
[How]
Skip ramp combining designed for RGB256 and DXGI gamma with CS_TFM_1D.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For commits with allow_modeset=false and CRTC degamma changes the planes
aren't reset. This results in incorrect rendering.
[How]
Reset the planes when color management has changed on the CRTC.
Technically this will include regamma changes as well, but it doesn't
really after legacy userspace since those commit with
allow_modeset=true.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some backlight tests fail due to backlight settling
taking too long. This happens because the step
size used to change backlight levels is too small.
[How]
1. Change the size of the backlight gain step size
2. Change how DMCU firmware gets the step size value
so that it is passed in by driver during DMCU initn
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some displays take some time to power up AUX CH once they are
put into D3 state via write to DPCD 600h=2.
Interestingly enough, some display may simply NACK, but some might
also ACK with a bunch of 0s, which can cause issues with receiver
cap retrieval. Note that not all DPCD address return 0s, but in
particular it has been observed on some higher DPCD address such
as DPCD 2200h, etc.
[How]
Based on spec, receiver will monitor differential signal while in D3 and
AUX CH is in low power mode. When detected, it may allow up to
1 ms to power up AUX CH and reply.
If we read Sink power state D3, we should add 1 ms delay to satisfy
this spec requirement.
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description] This is cause by failing to read link caps from driver.
Signed-off-by: Daniel He <daniel.he@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding writeback_config enum to vba_vars_st, replacing old flag.
Initialize to dm_normal.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.
[How]
* Pull get_active_display_cnt out to clk_mgr.
* Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Value read from SMU is 16 bits, not 32.
[How]
Fix type, and add wm_type enum in preparation for future interfaces.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Modern Standby may toggle display adapter state between D0
and D3 state unpredictably.
But events that cause transition to D0 are not always resulting
in a display light up scenario.
Modern eDP panels should be able to power on panel logic
quickly upon VDD going high. Based on spec, the T3 time
between VDD on and HPD high can be between 0 and 80 ms.
Doing any tricky sorts of optimization by powering on panel
VDD early during D0 transition on can negatively impact other
features due to unnecessary power drain and toggling when
final system state does not intend for the panel to be lit up.
We need OEMs to source higher end panels that have T3 time
close to 0 if they want quick S3/Modern Standby resume times.
[How]
Remove panel VDD power on in init_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
during It's possible to call dcn_validate_bandwidth with no plane.
In that case, as we are only intersted in if output timing is supported or not,
even if we cannot support native resolution, we still want to support lower
resolution if it is valid
[how]
if there exist no surface, make viewport/rec_out size at max 1080p. It is
already known that 1080p x 6(max # of pipes) is supported, so if we fail
validation, it is because of the stream
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
by adding fast_validate flag, we are skipping some portion of
dcn_validate_bandwidth code that is not necessary for mode validation.
However we have a bug where it does not calculate
v->total_data_read_bandwidth, which is one of the factors determines the
result of the validation, and therefore report false positive during
mode validation.
[how]
add calculation of v->total_data_read_bandwidth outside of the region
that is guarded by fast_validate flag
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
link-specific functions should reside in dc_link.c
[How]
Move them there.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add min_dcfclk_mhz to bounding box overrides.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Better organization
[How]
Move clk_mgr files under dc/clk_mgr
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. DMCU is not running on some platform but driver still send ABM
command. It may cause assert due to DMCU is not alive.
2. To make sure PSR disable when driver disable
[How]
1. Add dmcu_is_running in ABM struct, driver can check this flag to
determine driver should send ABM command or not.
2. Send PSR disable command when destroy PSR
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the previous implementation DRR event sometimes came
in during FP2 region which is a keep-out zone. This
would cause the frame not to latch until the next frame
which resulted in heavy flicker. To fix this we need
to make sure that it triggers in the BP.
[How]
1. Remove DRR programming during flip
2. Setup manual trigger for DRR event and trigger it
after surface programming is complete
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GSL is a form of locking that can be used to synchronize pipes in a
pipe-split configurations when async flip is used. Add the registers
here.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously there were 2 consecutive calls being made to disable
audio stream. The first one disabled the audio stream, and the second
one went through and also tried to disable the audio stream causing
BACO entry issues due to the ASIC appearing busy.
[How]
1. Add a status field to the audio struct which stores enabled/disabled
info
2. In the calls to enable/disable audio stream check if we're already
in the desired state before executing the function
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
stream id should uniquely identify an instance of stream.
the copy constructor should be treated as a new
stream instance.
[how]
assign a new stream id in this copy constructor.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This macro is specificly used by RV1. Move it to the appropriate
location.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add vtable entries for de-alpha and bias color management interfaces.
Move piece-wise transfer function registers to a helper list for future
reuse.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We can’t use hardcoded SRGB ROM for output TF if we have GAMMA_CS_TFM_1D
(unless we know 1D LUT is identity), so we never want to return here early.
We apply the LUT part of ColorTransform3x4 only in apply_lut_1d() which is
called near the end of that function.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
First step of refactoring clk mgr to better handle different
ways of handling clock operations. Clock operation policies are
soc specific and not just DCN vesion specific. It is not a hw resource,
should not be in the resource pool.
[How]
Change clock manager creation to be based on HW internal ID, rename
clock manager members to be more clear. Move clock manager out of
resource.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New stuff for 5.3:
- Add new thermal sensors for vega asics
- Various RAS fixes
- Add sysfs interface for memory interface utilization
- Use HMM rather than mmu notifier for user pages
- Expose xgmi topology via kfd
- SR-IOV fixes
- Fixes for manual driver reload
- Add unique identifier for vega asics
- Clean up user fence handling with UVD/VCE/VCN blocks
- Convert DC to use core bpc attribute rather than a custom one
- Add GWS support for KFD
- Vega powerplay improvements
- Add CRC support for DCE 12
- SR-IOV support for new security policy
- Various cleanups
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190529220944.14464-1-alexander.deucher@amd.com
dc_destroy should be called amdgpu_cgs_destroy_device,
as it will use cgs context to read or write registers.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
