[Why]
This function is not being used, it was left in
when introducing DCN2
[How]
Remove the function
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
during a refactor a redundant code that has unknown behaviour was added.
[how]
removed old bad code
Fixes: 8a31820b12 ("drm/amd/display: Make init_hw and init_pipes generic for seamless boot")
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How] Allocate memory for default page and program memory block addr
into default page addr register.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
IEEE OUI will now be used while referring to certain vendors.
instead of normal index
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before a statically allocated PPS data structure, that did
get zeroed-out at startup, had been re-used for making packed PPS
SDP. With S3 fix, using a non-initialized PPS data structure was
introduced, while wrongly assuming it'd get initialized before it's
populated. As a consequence 'vbr_enable' and perhaps some other
fields are left uninitialized when making packed PPS SDP. This can
affect 'simple_422' as well because of the way PPS SDP packing is
done (the fields are not masked first, only shifted). The behavior
will be different, depending on the content of uninitialized data.
[how]
Zero-out PPS data structure at initialization time before it's
populated
Fixes: 1a9e3d4569 ("drm/amd/display: Set DSC before DIG front-end is connected to its back-end")
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add new function to get the voltage at the end of
dcn_validate_bandwidth, to check against the
highest voltage we allow.
Created a stub to allow for optimizations
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Sun peng Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adding NULL checks to various parameters in log_tf, to avoid
nullptr errors
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Nikola Cornij <Nikola.Cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the writeback Hratio and Vratio in dml.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A previous odm change broke stream enable by always setting
n_multiply as if odm was on.
This fixes the check for odm by making sure opp count is >1
rather than not 0.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
With Scatter Gather enabled, HUBP underflows during MPO enabled video
playback. hubp_init has a register write that fixes this problem, but
the register is cleared when HUBP gets power gated.
[how]
Make a call to hubp_init during enable_plane, so that the fix can
be applied after HUBP powers back on again.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Disable_audio_stream gets enum option as a paramenter which will decide
if we free acquired resources or not. However checks for the option is
guarded by the other condition which check if audio stream is getting
diabled more than once. With both conditions combined, if we attempt to
disable audio stream twice in a row, first with keep and second with
free as an option, we will never free any resources, which will make
system think there is audio endpoint connected even after we plug out
the device
[How]
Get rid of option as parameter to disable_audio_stream and move the part
of the code that free acquired resources to outside where to keep or to
free resources is actually determined
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dig_encoder_sel_to_atom will always return zero on any ASIC version
past DCE80 since programming of the FE selection is handled by
driver, but the translation code was left in the function, making
it look like a coding error.
[How]
Remove code that has no effect, and replace with a comment describing
why it returns zero.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm is handled using top_bottom pipe by special casing
the differing opps to differentiate from mpc combine.
Since top/bottom pipe list was made to track mpc muxing this creates
difficulties in adding a 4 pipe odm case support.
Rather than continue using mpc combine list, this change reworks odm
to use it's own linked list to keep track of odm combine pipes. This
also opens up options for using mpo with odm, if a practical use case
is ever found.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a dcfeaturemask flag for mclk switching. Disable by default;
enable once the feature has seen more testing.
Set amdgpu.dcfeaturemask=2 on the kernel command line in grub
to enable this.
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Properly set all_displays_in_sync so that when the data is
propagated to powerplay, it's set properly and we can enable
mclk switching when all monitors are in sync.
v2: fix logic, clean up
v3: check for blending chains, simplify logic
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was broken by a previous change switching to cached fw_info.
Fixed by inverting a valid bool check.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=111432
Fixes: 9adc8050bf ("drm/amd/display: make firmware info only load once during dc_bios create")
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the pointer init_data is dereferenced on the assignment
of fw_info before init_data is sanity checked to see if it is null.
Fix te potential null pointer dereference on init_data by only
performing dereference after it is null checked.
Addresses-Coverity: ("Dereference before null check")
Fixes: 9adc8050bf ("drm/amd/display: make firmware info only load once during dc_bios create")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 80e80ec817.
This commit fixed an issue with underscan commits not updating all
needed timing values, but through various refactors it is no longer
necessary. It causes corruption on odm combine by
overwriting the halved h_active in the stream timing
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 6c5be4ac63.
This commit was accidentally promoted twice
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit ec8763486d.
Re-enable enc2_dp_set_dsc_config. This function caused warnings
due to missing register definitions. With the registers added,
this now works
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 9e14d4f17e.
optc dsc config was causing warnings due to missing register
definitions. With the registers restored, the function can
be re-enabled
The reverted commit also disabled sanity checks and dsc
power gating. The sanity check warnings are not associated
with dsc, and power gating on dsc still has an issue on
non-dsc monitors where the dsc hardware block is never init
and so cannot respond to power gating requests. Therefore,
those are left as is
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When building arm32 allyesconfig:
ld.lld: error: undefined symbol: __aeabi_uldivmod
>>> referenced by dc_link.c
>>> gpu/drm/amd/display/dc/core/dc_link.o:(wait_for_alt_mode) in archive drivers/built-in.a
>>> referenced by dc_link.c
>>> gpu/drm/amd/display/dc/core/dc_link.o:(wait_for_alt_mode) in archive drivers/built-in.a
time_taken_in_ns is of type unsigned long long so we need to use div_u64
to avoid this error.
Fixes: b5b1f45549 ("drm/amd/display: Enable type C hotplug")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous SOC bounding box firmware loading logic was for NV10, when we
still had it in firmware. Now that it's brought into driver code, and
NV12 BB is in firmware, this logic needs to be repurposed for NV12.
[How]
Set SOC_BOUNDING_BOX_VALID to false, and add the dcn_2_0_nv12_soc BB
struct. In init_soc_bounding_box, load firmware to nv12 BB instead.
In addition, conditionally update and patch the BB, depending on ASIC
REV.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN10 performs color processing before MPC combination, causes color
shift in RGB colorspaces when positive brightness offset is applied
However, YCbCr is still unfixed and remains disabled
[How]
Add layerIndex to dc_plane_state and dc_plane_info structs
Re-enable MPO when brightness is adjusted and colorspace is not YCbCr
Set rear plane's brightness offset to 0 when front plane visible
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
disable_az_endpoint has been skipped because
dc->debug.az_endpoint_mute_only = true.
[how]
set dc->debug.az_endpoint_mute_only false when PPLIB’s PME notification function
pointer is not NULL at the dcn10_resource construct function,because right now
SMU/PPLIB and DAL all have the AZ D3 force PME notification implemented. AZ D3 should work.
Signed-off-by: yanyan kang <Yanyan.Kang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
During detection link training if a display is disconnected,
the current code will retry 3 times of link training
on disconnected link before giving up.
[how]
Before each retry check for HPD status, only retry
verify link cap when HPD is still high.
Also put a 10ms delay between each retry to improve
the chance of success.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable dcn_mem_pwr as golden setting updates
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the paremeters are extracted as if dml is calculating
using pipes as we pass them in. in reality, dml internally merges
pipes into planes if pipe split is detected.
This change adds reverse logic to dcn20_calculate_dlg_params so
that the global sync parameters can be correctly extracted for
all the pipes when pipe split is enabled.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some logs messages were not precise and some new log messages
were needed after "get packed PPS" function was introduced
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A recent bug showed that logging would be useful in debugging
various gamma issues.
[How]
Add logging in dc.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are repeated (but guarded) definitions of dwb_src enums. There are
also unused entires. Clean them up.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These are needed to send back DRM vblank events in the case where VRR
is on. Without the interrupt enabled we're deferring the events into the
vblank queue and userspace is left waiting forever to get back the
events they need.
Found using igt@kms_vrr - the test fails immediately due to vblank
timeout.
[How]
Register them the same way we're handling it for DCN1.
This fixes igt@kms_vrr for DCN2.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
OGAM_MEM_PWR could stay in light up when driver woke up to update gamma.
either disable MEM_LOW power feature or set to OGAM_bypass could make artificial color distortion goes away.
Easy reproduce after LOW_MEM Power feature enables and resume from S3.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Julian Parkin <jparkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
A misleading message "Programming PPS" appears before both programming
and "query PPS" functions
[how]
Move the message from "log PPS" function to "program PPS" function
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not all ASIC types have this function implemented - check before
calling.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Julian Parkin <jparkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The type was changed previously to better reflect possible register
values.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If DSC is available, a higher picture quality is achieved by using
DSC with 4:4:4 format. Using 4:2:2 instead does not offer any benefit
and would only introduce loss of quality. Removing it reduces
maintenance and testing effort.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The vm config will be clear to 0 when system enter S4. It will
cause hubbub didn't know how to fetch data when system resume.
The flip always pending because earliest_inuse_address and
request_address are different.
[How]
Reprogram VM config when system resume
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and How]
We want to change where timing is done for alt mode.
Some of the commented out #ifs are needed for DCN20
so we enable them for that case.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Need to change interface function signature / add an enum
to reflect the available register field values
[How]
- Add a new enum and modify existing functions to use it instead
of bool
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current optc odm interface only accepts 2 opps, we need to
expand this to allow 4 to 1 odm combine.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to add DML struct members that were omitted in previous
DML implemenations.
[How]
- Add missing enum values
- Add missing struct members
- Set new input values in the fetch functions
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are currently two interfaces for exactly the same thing:
hupb_update_dchub in hupb and update_dchub in hubbub. The hubbub
version is currently unused past dcn10, largely because the call
from the dcn10 hardware sequencer does not call through the
interface, so the hupb interface was used instead. This is
confusing because of the duplicate code, the unused functions,
and the fact that more that one block currently owns this set
of registers.
[How]
Remove the hubp interface entirely, as well as the register
declarations that are not longer needed because of this. Change
the call site to always call the hubbub version through the
interface. Fix the update_dchub function in dcn20_hubbub.c to
program the correct registers for dcn20.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Resource mapping done in dcn20_validate_bandwidth has a flaw: When a full
update is performed, the HWSS will only update the MPCC tree for the stream
that is updated as opposed to all streams. This means that when mapping pipes
in validation, care must be taken to not change any existing mapping, otherwise it
leads to partial hw programming
[how]
it's not strictly necessary to track which stream/mpcc tree is being updated, but
rather it's sufficient to compare current and new state and just keep pipes that were
previously already mapped unchanged.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
At the time DIG FE is connected to its BE, the clocks in OTG are enabled and
PHY will also be set up. When DSC has to be used to fit the stream into the
available bandwidth, without DSC being set DIG could get exposed to the
higer bandwidth it (or link) could handle. This causes the HW to "reject"
video enable setup (the register shows that video enable was attempted, but
the status bit shows it as disabled).
[how]
- Separate DSC setup into DSC register config and DSC PPS SDP setup
- Move most of the DSC setup (register config) to before
dcn10_link_encoder_connect_dig_be_to_fe() is called
- Set up DSC PPS SDP after DIG FE is connected to its BE. This is because
setting DSC PPS SDP before that has no effect.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why] Minimum slice height is recommended by VESA DSC Spreadsheet user guide
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous "less risky" implemenation of 3 tiered fallback is no longer necessary since
DMLv2 has gone through proper validation. v2 can now be used as the default and 1
level of fallback can be removed
[how]
remove previous workaround implemenation
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot (building SW state inheriting BIOS-initialized timing) was
enabled on DCN2, including fixes
[How]
Includes fixes for MPC, DPPCLK, and DIG FE mapping/OTG source select/
Pixel clock.
This is part 2 of 2 for seamless boot NV10
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
underflow seen on certain monitor setups caused by making dcnxx_init_hw
generic
[How]
by moving dcn20_init_hw into dcn10, we added a dcn-specific clk_mgr
init (dc->clk_mgr->funcs->init_clocks()). Thus, put old clk_mgr
memset in an else statement so both memsets don't get set
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For seamless boot the init_hw sequence must be split into
actual hardware vs pipes, in order to defer pipe initialization to set mode
and skip of pipe-destructive sequences
[How]
made dcn10_init_hw and dcn10_init_pipes generic for future dcns to inherit
deleted dcn20 specific versions. This is part 1 of a 2 partimplementation
of seamless boot
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When planes are enabled, they must be enabled using VSYNC update (not immediate).
However, before the VUPDATE occurs, DM may call with an "immediate" flip which is address
only. This operation would normally be okay, but if the locking for immediate flip happens
to occur before the VUPDATE associated with the initial plane enablement, it will cause HW
to hang.
[how]
HWSS should enforce plane enable in HW to be synchronous with the call that enables the plane.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
if dynamic allocation fails during gpio_open, it will cause crash due to
page fault.
[how]
handle allocation when gpio object gets created and prevent from calling
gpio_open if allocation failed
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Auto Overclock Memory fails for some systems that don't support
p-state.
[How] Implement the workaround, and it's corresponding enable flag.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DC does not correct account for the fact that DPP DTO is double buffered while DPP ref is not.
This means that when DPP ref clock is lowered when it's "safe to lower", the DPP blocks that need
an increased divider will temporarily have actual DPP clock drop below minimum while DTO
double buffering takes effect. This results in temporary underflow.
[how]
To fix this, DPP clock cannot be programmed atomically, but rather be broken up into the DTO and the
ref. Each has a separate "safe to lower" logic. When doing "prepare" the ref and dividers may only increase.
When doing "optimize", both may decrease. It is guaranteed that we won't exceed max DPP clock because
we do not use dividers larger than 1.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently every time DC wants to access firmware info we make a call
into VBIOS. This makes no sense as there is nothing that can change
runtime inside fw info and can cause issues when calling unstable
bios during bringup.
This change eliminate this behavior by only calling bios once for fw
info and keeping it stored as part of dc_bios.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We require a method to perform synchronous link training.
[HOW]
Sync LT is broken into 3 basic steps.
"Begin" starts the state machine, and resets "preferred" link settings.
"Attempt" will attempt to train the link with a given set of training
parameters.
"End" stops the state machine, and will optionally disable the link phy.
Between "Begin" and "End" DPCD:600h must not be set to "2"
(D3:Powered Down).
Between "Begin" and "End", there may be multiple "Attempts" with different
training parameters.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DCN20 common register list that contains registers shared
between DCN20 generations.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Support degamma ROM and RAM based on hardware capabilities.
Some refactoring into color module
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Gary Kattan <Gary.Kattan@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When endpoint is at the boundary of a region, such as at 2^0=1
we find that the last segment has a sharp slope and some points
are clipped at the top.
[How]
If end point is 1, which is exactly at the 2^0 region boundary, we
need to program an additional region beyond this point.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
hdmi data scramble and tmds rate is not reset during pipe reset.
[how]
reset hdmi tmds rate and data scramble on pipe reset
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
drr is still enabled after driver is unloaded causing black screen
[how]
disable drr during pipe reset.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add to clk_mgr_internal struct, for future use.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For use by future ASICs
Signed-off-by: Sung Lee <sung.lee@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should be 'dce_audio_mask', not 'dce_aduio_mask'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's large and doesn't need contiguous memory. Fixes
allocation failures in some cases.
v2: kvfree the memory.
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This file was accidentally added to the driver during
Navi promotion
Nothing includes it. No makefile attempts to compile it, and
it would fail compilation if they tried
Remove it
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>w
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We were previously forcing the uclk for every state to max and reducing
the switch time to prevent uclk switching from occuring. This workaround
was previously needed in order to avoid hangs + underflow under certain
display configurations.
Now that DC has the proper fix complete we can drop the hacks and
improve power for most display configurations.
[How]
We still need the function pointers hooked up to grab the real uclk
states from pplib. The rest of the prior hack can be reverted.
The key requirements here are really just DC support, updated firmware,
and support for disabling p-state support when needed in pplib/smu.
When these requirements are met uclk switching works without underflow
or hangs.
Fixes: 02316e963a ("drm/amd/display: Force uclk to max for every state")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to support uclk switching on NV10 the SOC bounding box
needs to be updated.
[How]
We currently read the constants from the gpu info FW, but supporting
workarounds in DC for different versions of the FW adds additional
complexity to the codebase.
NV10 has been released so it's cleanest to keep the bounding box and
source code in sync by embedding the bounding box like we do for
other ASICs.
Fixes: 02316e963a ("drm/amd/display: Force uclk to max for every state")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some code was missing the CONFIG_DRM_AMD_DC_DSC_SUPPORT guard.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently the allocation of config may fail and a null pointer
dereference on config can occur. Fix this by added a null
check on a failed allocation of config.
Addresses-Coverity: ("Dereference null return")
Fixes: c2cd9d04ec ("drm/amd/display: Hook up calls to do stereo mux and dig programming to stereo control interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
arch/x86/Makefile disables SSE and SSE2 for the whole kernel. The
AMDGPU drivers modified in this patch re-enable SSE but not SSE2. Turn
on SSE2 to support emitting double precision floating point instructions
rather than calls to non-existent (usually available from gcc_s or
compiler_rt) floating point helper routines for Clang.
This was originally landed in:
commit 1011745073 ("drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines")
but reverted in:
commit 193392ed9f ("Revert "drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines"")
due to bugreports from GCC builds. Add guards to only do so for Clang.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=109487
Link: https://github.com/ClangBuiltLinux/linux/issues/327
Suggested-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hi Linus,
Please, pull the following patches that mark switch cases where we are
expecting to fall through. These patches are part of the ongoing efforts
to enable -Wimplicit-fallthrough. Most of them have been baking in linux-next
for a whole development cycle.
Also, pull the Makefile patch that globally enables the
-Wimplicit-fallthrough option.
Finally, some missing-break fixes that have been tagged for -stable:
- drm/amdkfd: Fix missing break in switch statement
- drm/amdgpu/gfx10: Fix missing break in switch statement
Notice that with these changes, we completely get rid of all the
fall-through warnings in the kernel.
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----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=J2sO
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull Wimplicit-fallthrough enablement from Gustavo A. R. Silva:
"This marks switch cases where we are expecting to fall through, and
globally enables the -Wimplicit-fallthrough option in the main
Makefile.
Finally, some missing-break fixes that have been tagged for -stable:
- drm/amdkfd: Fix missing break in switch statement
- drm/amdgpu/gfx10: Fix missing break in switch statement
With these changes, we completely get rid of all the fall-through
warnings in the kernel"
* tag 'Wimplicit-fallthrough-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
Makefile: Globally enable fall-through warning
drm/i915: Mark expected switch fall-throughs
drm/amd/display: Mark expected switch fall-throughs
drm/amdkfd/kfd_mqd_manager_v10: Avoid fall-through warning
drm/amdgpu/gfx10: Fix missing break in switch statement
drm/amdkfd: Fix missing break in switch statement
perf/x86/intel: Mark expected switch fall-throughs
mtd: onenand_base: Mark expected switch fall-through
afs: fsclient: Mark expected switch fall-throughs
afs: yfsclient: Mark expected switch fall-throughs
can: mark expected switch fall-throughs
firewire: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable -Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
[Why]
In an effort to stop redundant calls to dce110_disable_audio_stream
the audio->enabled flag was added to the audio resource struct. While
this state probably shouldn't have been tracked on the audio struct
itself it still works fine for some sequences.
However, it does not work for cases where we're freeing the audio
resource (such as hotplugs) or when dynamic audio is enabled.
In these cases the pipe_ctx->stream_res.audio = NULL before we can
set audio->enabled = false. The next time we acquire the audio resource
such as on hotplug the audio will not be enabled for the stream since
DC thinks it's still enabled.
Audio state tracking should cover this sequence.
[How]
Set audio->enabled = false at the start as long as we have
pipe_ctx->stream_res.audio.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]:
Some active dongles have DP++ port and DP port at the same time. Current
code doesn't cover DP++ case and processes as default DVI case, in which
audio is disabled. Because of dual mode, DP case is also treat as DVI case
for the other port.
[How]:
According DP 1.4 spec, add DP++ procedure similar with HDMI case. Also
add None dongle type for DP case.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC configures the GSL group for the pipe when pipe_split is enabled
and we're switching flip types (buffered <-> immediate flip) on DCN2.
In order to record what GSL group the pipe is using DC stores it in
the pipe's stream_res. DM is not aware of this internal grouping, nor
is DC resource.
So when DM creates a dc_state context and passes it to DC the current
GSL group is lost - DM never knew about it in the first place.
After 3 immediate flips we run out of GSL groups and we're no longer
able to correctly perform *any* flip for multi-pipe scenarios.
[How]
The gsl_group needs to be copied to the new context.
DM has no insight into GSL grouping and could even potentially create
a brand new context without referencing current hardware state. So this
makes the most sense to have happen in DC.
There are two places where DC can apply a new context:
- dc_commit_state
- dc_commit_updates_for_stream
But what's shared between both of these is apply_ctx_for_surface.
This logic only matters for DCN2, so it can be placed in
dcn20_apply_ctx_for_surface. Before doing any locking (where the GSL
group is setup) we can copy over the GSL groups before committing the
new context.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersen.wu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a flag to dc_debug_options to determine if a disconnected edp link
should be destroyed.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For some platforms, we need to know SMU version for driver/SMU
compatibility. This change adds that field.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Existing support in DC for pstate only accounts for a single latency. This is sufficient when the
variance of latency is small, or that pstate support isn't necessary for correct ASIC functionality.
Newer ASICs violate both existing assumptions. PState support is mandatory of correct ASIC
functionality, but not all latencies have to be supported. Existing code supports a "full p state" which
allows memory clock to change, but is hard for DCN to support (as it requires very large buffers).
New code will now fall back to a "dummy p state" support when "full p state" cannot be support.
This easy p state support should always be allowed.
[how]
Define a new latency in socBB. Add fallback logic to support it. Note DML is also updated to ensure
that fallback will always work.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN2x asic, the MPCC status register definition changed, and
our logic for assert is incorrect. disabled is valid state,
where we should see idle and not busy, where as in not
disabled state, we should see not idle.
[How]
Change assert condition to be more sensible.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously assume eDP sink present if connector present. Do not
need to enforce this restriction. Fix issue where driver attempt
to read link setting even though no edp connected.
{How]
Only read link setting after reading connection status.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES)
but the max number of audio devices (num_audio) is 7. In some projects,
it will run out of audios array.
[How]
Incraese the audios array size to 7.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For boards that support eDP but do not have a physical eDP
display connected an ASSERT will be thrown. This is not a
critical failure and shouldn't be treated as such.
[How]
Drop the assertion.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In an effort to stop redundant calls to dce110_disable_audio_stream
the audio->enabled flag was added to the audio resource struct. While
this state probably shouldn't have been tracked on the audio struct
itself it still works fine for some sequences.
However, it does not work for cases where we're freeing the audio
resource (such as hotplugs) or when dynamic audio is enabled.
In these cases the pipe_ctx->stream_res.audio = NULL before we can
set audio->enabled = false. The next time we acquire the audio resource
such as on hotplug the audio will not be enabled for the stream since
DC thinks it's still enabled.
Audio state tracking should cover this sequence.
[How]
Set audio->enabled = false at the start as long as we have
pipe_ctx->stream_res.audio.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Code to enable DCN20 dynamic metadata feature is duplicated in two places
and was added to DCE110 enable stream.
[How]
Create DCN20 specific enable stream function for clarity, and add a hardware
sequencer function to program dynamic metadata to avoid the duplicate
code.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In dm_helpers_parse_edid_caps, there is a corner case where no speakers
can be allocated even though the audio mode count is greater than 0.
Enabling audio when no speaker allocations exists can cause issues in
the video stream.
[How]
Add a check to not enable audio unless one or more speaker allocations
exist (since doing this can cause issues in the video stream).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It is possible (but very unlikely) that constructing dc fails
before current_state is created.
We support 666 color depth in some scenarios, but this
isn't handled in get_norm_pix_clk. It uses exactly the
same pixel clock as the 888 case.
[How]
Check for non null current_state before destructing.
Add case for 666 color depth to get_norm_pix_clk to
avoid assertion.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
update_bounding_box calculates intermediate bb states based on clock relationship
however, the last state doesn't need to maintain a minimum relationship, but should
actually contain maximum of every clock. otherwise maximum clocks are not usable
[how]
once the calculated bb is built, override the last state with max values
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add dual plane dcc programming support for
surfaces.
Removes unions from plane size and dcc params as they
serve no practical purpose only making our code
more convoluted. This results in easy dual plane
dcc and surface size programming.
Temporary diags_dm code is used to handle the interface
change without breaking functionality as a diags change
needs to be applied after this one.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
