dev_role_id only indicates whether the dev role
is enabled, not started (e.g. on IBSS merge,
the device role is enabled, but not started).
Checking for any role in ROC (in order to determine
whether dev role was started) is wrong as well,
especially in multi-vif env.
Check for started dev role only by checking the dev_hlid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This flag should be set per-vif, rather than globally.
Rename the flag to indicate IN_USE (rather than IDLE), as
in the default configuration (i.e. flag is clear) the vif
should be idle.
Change all the bit operations (and elp conditions) appropriately.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Since the conf_tx callback passes the vif as param,
we must have been added first (and mac80211 verifies it).
Remove the handling of such case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Implement the change_interface callback by simply removing the
current vif and adding a new one after updating the vif type.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl1271_configure_suspend_sta leaves a stale stack declared
completion in wlvif->ps_compl. Set it to NULL before returning.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[small fix to use wlvif->ps_compl instead of wl->ps_compl]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the newly introduced ieee80211_free_txskb() instead
of dev_kfree_skb() for failed tx packets.
Additionally, if the skb is a dummy packet, re-enqueue
it (as the fw expects it) instead of freeing it.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
During plt init we configure some redundant commands,
which are not needed for plt (specifically, we shouldn't
configure any role-specific params, as there are no
active roles). remove them.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use an appropriate mac80211 flags in CCMP keys to indicate we are
calculating the CCMP IV in HW, but require room for the IV to be reserved
in the skb. The space is reserved by mac80211.
depends on "mac80211: support adding IV-room in the skb for CCMP keys".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Print the name of nvs/fw if request_firmware fails. This will make
troubleshooting a bit easier.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
During reconfig we can get the BSS_CHANGED_AP_PROBE_RESP indication
even if a probe-resp has not been set in the first place. Therefore
ignore the error when not getting a probe-resp from mac80211. Resort to
the legacy probe-resp in this case.
Also take this opportunity to add a vif argument to the set_probe_resp
function.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx driver supports probe-response offloading, and the WPS, WPS2
and P2P special cases as well.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating in AP-mode, replace our probe-response template when a
notification is recieved from mac80211. We preserve the "legacy" way of
configuring a probe-response according to beacon for IBSS mode and for
versions of hostapd that do not support this feature.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Idle changes are currently handled per hardware.
However, some operations should be done only per-interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The sdio driver uses a block size of 512 bytes by default. With our
card, this doesn't work correctly because it sets the block size FBR
in the chip too early (ie. before the chip is powered on). Thus, if
we don't set it explicitly, block mode remains disabled in the chip.
If we try to send more data than fits in one block, the sdio driver
will split it into separate blocks before sending to the chip. This
causes problems because the chip is not expecting multiple blocks.
At the moment this is not a problem, because we use chunks of 512
bytes for firmware upload and the data is always sent in byte mode.
In the next patch, we will change the chunk size to a bigger value, so
this patch is a preparation for that.
Signed-off-by: Luciano Coelho <coelho@ti.com>
SDIO blocksize alignment support is now the rule, not the exception.
To simplify the code in patches to come, invert the meaning of the
quirk to be negative (ie. the quirk is set if the device does _not_
support blocksize alignment).
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl->vif should be cleared on remove_interface()
(rather than on stop()) even when only a single
vif is supported, because during vif mode change
stop() might not get called (e.g. because of
monitor interface existence)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The rate policies are configured only after association,
resulting in auth req being sent in wrong rates.
Reconfigure rate policies on bitrate mask change.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Device role is always started along with ROC.
Couple them together by introducing new wl12xx_start_dev
and wl12xx_stop_dev functions.
By using these functions, we solve a bug that occured during
channel switch - we started the dev role on one channel, and
ROCed on a different one.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Injected packets are sent with no vif, causing the wl12xx
to NULL-dereference in multiple places.
Furthermore, injected packets are currently not sent at all,
as system_hlid doesn't belong to any specific role, so
wl1271_skb_dequeue() never return its packets.
Handle both these problems.
Reported-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There's no need to have the bus name included in the platform device
name that we create. The core driver doesn't need to know about the
type of bus it uses. Any differences between the buses that need to
be handled differently in the core, can be passed in the platform data
(as the pwr_in_suspend boolean does).
Use "wl12xx" for the device name in both bus drivers. Rename the
platform driver name to "wl12xx_driver", just to differentiate from
the platform device names.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Separate the debugging macros and other definitions to a new debug.h
file. This is be needed because the sdio and spi modules don't need
to depend on the wl12xx module anymore, but still need to include
wl12xx.h. Currently they do depend on it, because of the debugging
global that wl12xx exports. A future patch will remove this
dependency.
Signed-off-by: Luciano Coelho <coelho@ti.com>
now that useless plat_dev is unnecessary,
we can remove it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[forward ported and fixed sysfs file creation]
Signed-off-by: Luciano Coelho <coelho@ti.com>
after re-factoring a bunch of symbols are only
used inside main.c which allows us to mark
them as static.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[forward-ported]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Move all common parts from sdio.c and spi.c to main.c, since they now
can be handled as part of the platform driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[forward-ported, cleaned-up and rephrased commit message]
[added a bunch of fixes and a new pdata element]
[moved some new code into main.c as well]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Nnow that we have a platform_device on both glue layers, add a
platform_driver to the core driver.
It's currently an empty platform_driver but more functionality will be
added on later patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[forward-ported, cleaned-up and rephrased commit message]
[added platform_driver.driver initialization]
Signed-off-by: Luciano Coelho <coelho@ti.com>
Currently, a single vif might starve all the other vifs.
Save the last vif we dequeued a packet from, and continue
with the following one using a round-robin policy.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
add_interface might be called while the chip is
in elp. add elp_wakeup/sleep calls to handle it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
allocate the rate policies dynamically, instead of using hardcoded
indexes. this is needed for proper multi-role configuration.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The recovery work should call stop() after it removed
all the existing interfaces.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl->vif is appropriate only when a single vif is being used.
Instead, pass wlvif as parameter or iterate through all
the vifs (e.g. when a global configuration was changed)
Leave wl->vif only to determine whether a vif was already
added (this check will be removed as well after both the
driver and fw will support multiple vifs)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When mac80211 changes a global (hw) config, iterate
through all the relevant vifs and update them.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move power_level into the per-interface data.
mac80211 configures some values (e.g. band, channel)
globally, while we configure them per-interface.
In order to make it easier to keep track of the
configured value for each value while keeping sync
with mac80211, save these values both globally
and per-vif.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
add channel into the per-interface data.
mac80211 configures some values (e.g. band, channel)
globally, while we configure them per-interface.
In order to make it easier to keep track of the
configured value for each value while keeping sync
with mac80211, save these values both globally
and per-vif.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
add band field into the per-interface data.
mac80211 configures some values (e.g. band, channel)
globally, while we configure them per-interface.
In order to make it easier to keep track of the
configured value for each value while keeping sync
with mac80211, save these values both globally
and per-vif.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make the initialization flag per-vif, and add some checks for it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move WL1271_FLAG_PSM and WL1271_FLAG_PSM_REQUESTED into
per-vif flags.
These flags should be set per-vif, rather than globally.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Currently, the rx streaming doesn't support multi-vif
(the actual wlvif is taken from wl->vif, and the management
is global).
Make the rx streaming timers/works per-vif, and pass the
the actual vif as param.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The last security seq num has to be saved across reconfigs.
Add a new "persistent" struct into wlvif, which won't get
deleted on wl12xx_init_vif_data()
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If there is an active AP role, stay always on.
Otherwise, allow chip to enter elp.
(Note that this is a global configuration, so if the
device is already configured according to our policy,
we don't have to configure it again)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pass the wlvif associated with each skb as param.
Note that dummy packet doesn't belong to any
particular vif, so we pass NULL in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
keep a list of all the vifs associated with our hw.
it will be later used in order to iterate through vifs.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move bitrate_masks into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Leave only vif-specific deinit stuff in remove_interface().
Move the global deinit (including power_off) to stop().
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make sta use the global wl->links[hlid].tx_queue (by
considering its links map) instead of wl->tx_queue,
and then unify the tx and tx_reset flows for the
various vifs.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move last_tx_hlid into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The fw boot and initialization currently happens inside the
add_interface() callback. This is wrong, as add_interface is
called for each new vif. However, we due to some fw limitation
(we have to know the actual mac address on boot), we can't
completely move it into the start() callback.
Until the fw will be fixed, refactor the fw init into
a new function, and call it from add_interface()
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move recorded_ap_keys into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add wlvif->links_map bitmap to represent all the links
allocated for this vif.
AP vif also has a sta_hlid_map bitmap, which represents
the links stations connected to it (sta_hlid_bitmap is
a subset of wlvif->links_map, which itself is a subset
of the global wl->links_map)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move ba_fields into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move rssi_thold and last_rssi_event into the per-interface
data, rather than being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move ps_poll_failures and psm_entry_retries into the per-interface
data, rather than being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move ps_compl into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move pspoll_work into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move default_key into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move beacon_int into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move dev_hlid into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move session_counter into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move ap_global_hlid and ap_bcast_hlid into the per-interface
data, rather than being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move sta_hlid into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move dev_role_id into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move role_id into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move aid into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move probereq into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move ssid and ssid_len into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move p2p field into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move bss_type into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the per-interface vif->bss_conf instead of the global wl->bssid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move basic_rate into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
move rate_set into the per-interface data, rather than
being global.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Define a per-vif data struct.
This struct holds all the vif-specifc data, which is
currently being hold by the global wl struct.
Start by moving the basic_rate_set field into it.
NOTE: in order to make the patches a bit smaller, start by
using wl->vif in some functions, instead of changing all
the function prototypes at once. finally, wl->vif will be
removed altogether.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Split the init sequence into common commands (non role-specific)
and role-specific commands.
We still need to call the common commands only on add_interface()
(rather than on start()) as the fw must get the mac address
when uploading the nvs.
Future patches will refactor the init sequence further more.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[fixed a couple of sparse warnings]
Signed-off-by: Luciano Coelho <coelho@ti.com>
The mac address of the interface already exists in vif->addr.
Use it instead of wl->mac_addr.
It seems that due to some fw bug, we still need to set nvs->mac
to the actual mac addresss, otherwise the fw doesn't function
well (e.g. can't get dhcp address).
Thus, use wl->mac_addr for this purpose, and don't delete it yet.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current wl12xx fw (7.3.0.0.77) supports both STA and AP mode, and
we no longer use AP-mode-specific quirks.
WL12XX_QUIRK_END_OF_TRANSACTION is still used for certain HWs, while
WL12XX_QUIRK_LPD_MODE is not used anymore.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx FW supports HW channel switch. If we don't use it,
sometimes the firmware gets confused when recalibrating to the new
channel, causing RX problems. This commit adds HW channel switch
support by implementing the channell_switch op.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
[added one comment, remove the tx_flush and rephrased the commit message]
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wiphy max_sched_scan_ie_len attribute was not set correctly and
remained as 0, so when IEs were being passed in a scheduled scan, we
were returning -EINVAL.
Fix this by setting the attribute properly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
tx params should be configured per interface.
add ieee80211_vif param to the conf_tx callback,
and change all the drivers that use this callback.
The following spatch was used:
@rule1@
struct ieee80211_ops ops;
identifier conf_tx_op;
@@
ops.conf_tx = conf_tx_op;
@rule2@
identifier rule1.conf_tx_op;
identifier hw, queue, params;
@@
conf_tx_op (
- struct ieee80211_hw *hw,
+ struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u16 queue,
const struct ieee80211_tx_queue_params *params) {...}
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.
Update all the drivers that implement these callbacks.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an erroneous labeling of array boundaries in the fw_status structure.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Save the configured bitrate, and use the min allowed rate
as the basic rate (e.g. when scanning).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If a hidden SSID is requested, generate a probe response template
containing the real SSID.
Depends on the patch "mac80211: add ssid config to bss information
in AP-mode".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There is a race condition between wl1271_tx_work() and the
channel switch, so make sure all the pending packets are
being sent before switching channel.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx uses a single probe response template, regardless of
the probe request.
However, the P2P spec forbids including the p2p ie in some
cases (e.g. the probe request didn't include the p2p ie).
The fw responds only to probe requests that don't
include the p2p ie, and passes up probe requests that
include them (the supplicant will answer them).
Thus, strip the p2p ie from the probe response template.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx uses the beacon as the probe response template.
However, the beacon includes a TIM ie, which shouldn't
exist in the probe response.
Delete it from the skb before configuring the probe
response template.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were including only 11b rates in IBSS mode. This patch adds OFDM
rates.
[Rephrased commit log and removed one unnecessary comment. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Declare support for p2p interfaces, and create p2p_cli/p2p_go
roles when being asked for.
Indicate we are using a p2p interface by setting the wl->p2p flag.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We set the mac80211 flag for A-MPDU support and also indicate that
Tx-agg session setup is performed in HW.
This patch depends on
"mac80211: add flag to indicate HW only Tx-agg setup support"
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reset the BA state of all connected stations and explicitly clear the
Tx queues. The latter is needed for clearing dummy packets from
tx_queue_count.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When operating as AP track the number of connected stations. When a
single STA is connected don't regulate the PS status of the link.
Since this is the only STA connected, there's no point holding space in
FW for other links. This will speed up communications with a single
connected STA in PSM.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The latest firmware supports up to 16 SSIDs in the scheduled scan
lists. Increase the number we report to cfg80211 and increase the
min/max dwell time to 30 and 60 TUs respectively, because otherwise we
don't have the time to send the probes for all SSIDs.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Declare support for uapsd when working as AP, and
set psd_type and sp_len whan a station is being added.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
