When a controller requires external configuration, then setting this
quirk will allow indicating this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Reading the controller configuration information is a valid management
command when the controller is unconfigured. Allow this command, but
return invalid index on all other commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a Bluetooth controller does not have a valid public Bluetooth
address, then allow the driver to indicate this. If the quirk is
set, the Bluetooth core will switch to unconfigured state first
and will allow userspace to configure the address before starting
the full initialization of the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's wasteful to use list_del_init (which re-initializes the list_head)
if we're just about to free the element and never use it again.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a found device is marked as blocked while doing passive LE scanning,
neither report it nor try to connect to it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of looking through the entire list of entries we can more
efficiently use the new hci_pend_le_action_lookup() function to look up
entries specifically in the pend_le_reports list. Since the search is
now limited to the right list we can also remove an unnecessary check
for list_empty() before the lookup.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances we need to look up entries in pend_le_conns and in
other in pend_le_reports. This patch converts the existing lookup
function for pend_le_conns to something that can be used for both lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since there are no more users of this function we can simply go ahead
and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is the last place using hci_pend_le_conn_add() and we can more
just as simply manipulate the list directly here.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When powering off (hci_dev_do_close) we should clear both the
pend_le_reports and pend_le_conns types of entries. When powering on
respectively we should populate both lists. This patch converts the
hci_pend_le_conns_clear() function into hci_pend_le_actions_clear()
(which can now be static) and converts the restart_le_auto_conns()
function into restart_le_actions().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there are no-longer any users of the hci_pend_le_conn_del()
function we can simply go ahead and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since params->action is used for both the pend_le_conns and
pend_le_reports lists we can simplify the adding and deleting of the
lists considerably. For example, when deleting entries in most
situations we no-longer need to check the auto_connect value but can
directly proceed with calling list_del_init on param->action (which is
safe even if the entry is not part of any list).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hci_conn_params_set() is called if the new auto_connect value is
the same as the old one we don't need to take any action. Simply return
success from the function in this case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that pend_le_connections is a list of hci_conn_params entries we can
simply remove items from that list as we iterate through the global list
of le_conn_params. This also moves the responsibility of calling
hci_update_background_scan() to the functions that were previously
calling hci_pend_le_conns_clear(). The only user that's left for
hci_pend_le_conns_clear() is hci_dev_do_close() which anyway does not
need to call hci_update_background_scan().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation to store also HCI_AUTO_CONN_REPORT entries in a list it
makes sense to convert the existing pend_le_conn list head of
hci_conn_params into a more generically named "action". This makes sense
because a parameter entry will never participate in more than one action
list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we're doing passive scanning we shouldn't proceed with any of the
code that deals with active scanning (pending reports, etc.). This patch
fixes a missing return statement for the passive scanning section in the
process_adv_report() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Read Controller Configuration Information command allows retrieving
details about possible configurations option. The supported options are
returned and also the missing options (if any).
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since we only store entries with identity addresses in the
le_conn_params and pend_le_conns lists we can avoid unnecessary lookups
by checking for an identity address before diving into the lists
themselves.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If a device is in the pend_le_conns list it cannot at the same time also
have the need to be notified through mgmt_device_found. By making
check_pending_le_conn return whether it found an entry or not we can
avoid unnecessary checks in process_adv_report().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the connection parameters are always a basis for adding entries to
hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more
efficient to have the parameters themselves be the entries in the
pend_le_conns list. We do this by adding another list_head to the
hci_conn_params struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When processing passive scanning results we need the resolved identity
address both in check_pending_le_conn() as well as later in
process_adv_report(). Since process_adv_report() calls
check_pending_le_conn() we can simply resolve the IRK earlier in the
function and thereby eliminate a second lookup.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When calling Remove Device for an entry using HCI_AUTO_CONN_REPORT we
need to decrement the pend_le_reports value correspondingly. This patch
fixes one such missing action in the Remove Device command handler.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The handler for variable length commands were trying to calculate the
expected length of the command based on the given parameter count, and
then comparing that with the received data. However, the expected count
was stored in a u16 which can easily overflow. With a carefully crafted
command this can then be made to match the given data even though the
parameter count is actually way too big, resulting in a buffer overflow
when parsing the parameters.
This patch fixes the issue by calculating a per-command maximum
parameter count and returns INVALID_PARAMS if it is exceeded.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're scanning for specific devices that use an RPA we need to
convert the RPA to the identity address before looking up the entry in
the connection parameters. This patch adds the necessary code to do this
in the process_adv_report() function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have one or more devices with HCI_AUTO_CONN_REPORT we should do
background scanning and emit mgmt_device_found events. This patch
modifies the hci_update_background_scan() function to extend the
conditions needed to trigger scanning, and adds the necessary code to
process_adv_report() to emit mgmt_device_found events.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the kernel is doing LE scanning because of one or more devices
added with action 0x00 through the Add Device command we do want to let
mgmt_device_found() to proceed with sending an event. This kind of
devices are tracked with hdev->pend_le_reports, so check this value
before bailing out from the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be able to make the right choice of whether to start passive scanning
or to send out a mgmt_device_found event we need to know if there are
any devices in the le_conn_params list with the auto_connect value set
to HCI_AUTO_CONN_REPORT. This patch adds a counter for this kind of
devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This command allows to get the list of currently known controller that
are in unconfigured state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller in an unconfigured state gets removed, then send
Unconfigured Index Removed events.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller is in unconfigured state it is currently hidden
from the management interface. This change now announces the new
controller with an Unconfigured Index Added event and allows clients
to easily detect the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the new unconfigured controller state it is possible to provide a
fully functional HCI transport, but disable the higher level operations
that would normally happen. This way userspace can try to configure the
controller before releases the unconfigured state.
The internal state is represented by HCI_UNCONFIGURED. This replaces the
HCI_QUIRK_RAW_DEVICE quirk as internal state representation. This is now
a real state and drivers can use the quirk to actually trigger this
state. In the future this will allow a more fine grained switching from
unconfigured state to configured state for controller inititialization.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we don't have an identity address for connection parameters it
doesn't really make sense to send them to user space. Instead just
ignore them for now. Later we can add support for sending them when we
eventually get the identity through pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are more places that can take advantage of is_identity_address()
besides hci_core.c. This patch moves the function to hci_core.h and
gives it the appropriate hci_ prefix.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The calling functions of mgmt_new_conn_param have more information about
the parameters, such as whether the kernel is tracking them or not. It
makes therefore sense to have them pass an initial store_hint value to
the mgmt_new_conn_param function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The caller of hci_le_conn_update is directly interested in knowing what
the best value is for the store_hint parameter of the corresponding
mgmt event. Since hci_le_conn_update knows whether there were stored
parameters that were updated or not we can have it return an initial
store_hint value to the caller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should update any stored connection parameters when we receive the LE
Remote Connection Parameter Request HCI event. This patch adds the
necessary code to the function that handles the event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch implements the new Load Connection Parameters mgmt command
that's intended to load the desired connection parameters for LE
devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Remove Device mgmt command is supposed to undo what the Add Device
command does. An entry added by Add Device cannot have the
HCI_AUTO_CONN_DISABLED auto_connect value, so we should treat this as an
invalid entry to remove. This patch adds the necessary pieces to the
Remove Device command handler so that it only removes entries which were
added by Add Device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The 0x00 action value of mgmt means "scan and report" but do not
connect. This is different from HCI_AUTO_CONN_DISABLED so we need a new
value for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances we'll need to either clear only the enabled
parameters or only the disabled ones. This patch adds convenience
functions for this purpose.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon have specific clear functions for clearing enabled or
disabled entries, so rename the function that removes everything to
clear_all().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When allocating a new controller structure, then default to the internal
use value 0xffff first. Default to 0x0000 is a bad idea since that is
the manufacturer identifier of Ericsson Technology Licensing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Unlike BR/EDR we cannot reject LE connections of blocked devices but
have to do it as soon as we get a LE Connection Complete event. The
patch adds a blacklist check to the hci_le_conn_complete_evt function
and drops all connections for blocked devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ATT channel isn't the only one that we should ensure doesn't receive
data from blocked devices. SMP is another, and in general we don't want
data packets going to any of the various handlers. Therefore, add a
single check to the l2cap_recv_frame function.
The patch fixes at the same time the use of a correct address type. The
blacklist stores the values with the user space facing triple type
wheras hci_conn->dst_type uses the HCI address type (0x00 or 0x01).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some embedded controllers allow the programming of a public address
and this adds vendor support for supporting OEM confguration of such
addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch introduces a new Mgmt event called "New Connection Parameter".
This event indicates to userspace the connection parameters values the
remote device requested.
The user may store these values and load them into kernel. This way, next
time a connection is established to that device, the kernel will use those
parameters values instead of the default ones.
This event is sent when the remote device requests new connection
parameters through connection parameter update procedure. This event is
not sent for slave connections.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth 4.1 introduces a new LE meta event called "LE Remote
Connection Parameter Request" event. In order to the controller
sends this event to host, we should enable it during controller
initialization.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During init2 phase, the LE local features have not be read yet so
we aren't able to rely on hdev->le_features to determine if the
controller supports the Connection Parameters Request Procedure.
For that reason, this patch moves LE event mask setting from init2
into init3 initialization phase.
The hdev->le_features mask will be checked by the next patch in order
to know if "LE Remote Connection Parameter Request Event" should be
enabled.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for LE Connection Parameters Request Link
Layer control procedure introduced in Core spec 4.1. This procedure
allows a Peripheral or Central to update the Link Layer connection
parameters of an established connection.
Regarding the acceptance of connection parameters, the LL procedure
follows the same approach of L2CAP procedure (see l2cap_conn_param_
update_req function). We accept any connection parameters values as
long as they are within the valid range.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the Block/Unblock Device mgmt commands we should only emit the
Blocked/Unblocked events on any socket except for the one which received
the command. The code was previously incorrectly trying to look up a
non-existent pending command and thereby ending up not skipping the
command socket for the event.
We can simplify the code a lot by simply sending the event directly from
the command handler functions. We have the reference to the command
socket available there which makes it easy to pass to the mgmt_event
function for skipping.
The only notable side-effect of this is that the old blacklisting
ioctl's no-longer cause mgmt events to be emitted, however as user space
versions using these ioctl's are not mgmt-aware this is acceptable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The background scanning normally gets enabled during power on by
adding devices to the pending connection list. However devices
might be already on that list and the list of devices is empty,
then it is better to trigger the background manually.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a new controller is initialized, but not powered from userspace
at the moment, the HCI_AUTO_OFF flag is still set. During this period,
userspace might program device for auto-connection, but never power
on the controller. In this case do not try to start background
scanning and leave it for later to be started.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If we're encrypted with the STK we should allow re-encryption with an
LTK even though the achieved security level is the same. This patch adds
the necessary logic to the smp_sufficient_security function which is
used to determine whether to proceed with encryption or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are certain subtle differences in behavior when we're encrypted
with the STK, such as allowing re-encryption even though the security
level stays the same. Because of this, add a flag to track whether we're
encrypted with an STK or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we're already encrypted with a good enough LTK we should just ignore
an incoming SMP Security Request. The code was already taking care of
this in the smp_conn_security function before calling smp_ltk_encrypt
but failed to do the same in smp_cmd_security_req. This patch fixes the
issue by moving up the smp_sufficient_security function and using it in
the Security Request handler before trying to request encryption.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Device Found events of the management interface should indicate if
it is possible to connect to a remote device or if it is broadcaster
only advertising. To allow this differentation the Not Connectable flag
is introduced that will be set when it is known that a device can not
be connected.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing the flags parameter directly to mgmt_device_found function
makes the core simpler and more readable. With this it becomes a lot
easier to add new flags in the future.
This also changes hci_inquiry_cache_update to just return that flags
needed for mgmt_device_found since that is its only use for the two
return parameters anyway.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The advertising data and scan response data are merged in the wrong
order. It should be advertsing data first and then scan response data
and not the other way around.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org # 3.16
The connection interval parameter of hci_conn_params_set are always used
with the controller defaults. So just let hci_conn_params_add set the
controller default and not bother resetting them to controller defaults
every time the hci_conn_params_set is called.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_conn_params_add function provides the default allocation of
connection parameters. To avoid code duplication, use that code from
hci_conn_params_set to allocate or lookup parameter struct.
As a benefit the connection latency and supervision timeout parameters
are no longer reset to default when calling hci_conn_params_set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When adding new connection parameters, it is useful to return either
the existing struct or the newly created one.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The return value of smp_ltk_encrypt is simple boolean, so just use
bool and make the code a bit more readable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is to support the Motorola HF850 carkit which reports the error
code 0x10 for an eSCO attempt, even though it advertises eSCO support.
With this patch we will retry with a SCO connection, which succeeds.
Signed-off-by: Nick Pelly <npelly@google.com>
Signed-off-by: Kiran Kumar Raparthy <kiran.kumar@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We have all the necessary remote information for getpeername() when we
are in the BT_CONFIG state so this should be allowed. This is
particularly important for LE sockets where changing the security level
will temporarily move the socket into BT_CONFIG state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bt_seq_ops is only used with __seq_open_private as
const struct seq_operations *
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch renames l2cap_check_conn_param() to hci_check_conn_params()
and moves it to hci_core.h so it can reused in others files. This helper
will be reused in the next patch.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the controller is not active or in init/setup phase, do not
try to start or stop background scanning.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When trying to pair a new Bluetooth Low Energy device, then make sure
that the default connections parameters are in place before trying to
establish the first connection to that device. With the connection
parameters structure allocated, the slave preferred values can now
easily be tracked and all future connections will use the correct
values from that start decreasing connection establishment time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some cases it is useful to not overwrite connection parametes and
instead just create default ones if they don't exist. This function
does exactly that. hci_conn_params_add will allow to create new
default connection parameters. hci_conn_params_set will set the
values and also create new parameters if they don't exist.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller has a default value for the supervision timeout. Expose
this via debugfs for testing purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller has a default value for the connection latency. Expose
this via debugfs for testing purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Store the connection latency and supervision timeout default values
with all the other controller defaults. And when needed use them
for new connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When devices are added or removed, then make sure that events are send
out to all other clients so that the list of devices can be easily
tracked. This is especially important when external clients are
adding or removing devices within the auto-connection list.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the auto-connection handling has gained offical management
command support, remove the le_auto_conn debugfs entry.
For debugging purposes replace it a simple device_list debugfs
entry that allows listing of the current internal auto-connection
list used for passive scanning.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This allows adding or removing devices from the background scanning
list the kernel maintains. Device flagged for auto-connection will
be automatically connected if they are found.
The passive scanning required for auto-connection will be started
and stopped on demand.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the LE connection parameters for connection latency and
supervision timeout are known, then use then. If they are not
know fallback to defaults.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the slave updates the connection parameters, store also the
connection latency and supervision timeout information in the
internal list of connection parameters for known devices.
Having these values available allowes the auto-connection
procedure to use the correct values from the beginning without
having to request an update on every connection establishment.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When calling hci_conn_params_clear function, it should update the
background scanning properly and not require a separate call to
update it.
For the case when the function is used during unregister of a
controller, an extra safe guard is but in place.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When hci_conn_params_clear is called, it is always followed by a
call to hci_pend_le_conns_clear. So instead of making this explicit
just make sure it is always called. This makes this function similar
on how hci_conn_params_add and hci_conn_params_del work.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_pend_le_conn_* function should be placed before their actual
users. So move them before hci_conn_params_* functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The usage of non-resovlable private addresses for passive scanning is
a bad idea. Passive scanning will not send any SCAN_REQ and thus using
your identity address for passive scanning is not a privacy issue.
It is important to use the identity address during passive scanning
since that is the only way devices using direct advertising will be
reported correctly by the controller. This is overlooked detail in
the Bluetooth specification that current controllers are not able
to report direct advertising events for other than their current
address.
When remote peers are using direct advertising and scanning is done
with non-resolvable private address these devices will not be found.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Bluetooth controllers that are marked for raw-only usage can only be
used with user channel access. Any other operation should be rejected.
This simplifies the whole raw-only support since it now depends on
the fact that the controller is marked with HCI_QUIRK_RAW_DEVICE and
runtime raw access is restricted to user channel operation.
The kernel internal processing of HCI commands and events is designed
around the case that either the kernel has full control over the device
or that the device is driven from userspace. This now makes a clear
distinction between these two possible operation modes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch implements support for the Get Clock Information mgmt
command. This is done by performing one or two HCI_Read_Clock commands
and creating the response from the stored values in the hci_dev and
hci_conn structs.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for storing the local and piconet clock values
from the HCI_Read_Clock command response to the hci_dev and hci_conn
structs. This will be later used in another patch to implement support
for the Get Clock Info mgmt command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By using kzalloc we ensure that there are no struct members, such as the
user_data pointer, left uninitialized.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch increments the management interface revision due to the
changes with the debug key command and other fixes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the connection is in master role and it is going to be
disconnected based on the disconnection timeout, then send
the HCI_Read_Clock_Offset command in an attempt to update the
clock offset value in the inquiry cache.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The abstraction of disconnect operation via hci_conn_disconnect is not
needed and it does not add any readability. Handle the difference of
AMP physical channels and BR/EDR/LE connection in the timeout callback.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_amp_disconn function is a local function and there is no
need for a reason parameter. That one can be retrieved from the
hci_conn object easily.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The smp_conn member of struct hci_conn was simply a pointer to the
l2cap_conn object. Since we already have hcon->l2cap_data that points to
the same thing there's no need to have this second variable. This patch
removes it and changes the single place that was using it to use
hcon->l2cap_data instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The smp_user_confirm_reply() function is called whenever user space
sends a user confirmation reply mgmt command. In case of a misbehaving
user space, or if the SMP session was removed by the time the command
comes it is important that we return an appropriate error and do not try
to access the non-existent SMP context. This patch adds the appropriate
check for the HCI_CONN_LE_SMP_PEND flag before proceeding further.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that the SMP context has it's own crypto handle it doesn't need to
lock the hci_dev anymore for most operations. This means that it is safe
to call smp_user_confirm_reply with the lock already held.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Passing the full SMP context instead of just the crypto context lets us
use the crypto handle from the context which in turn removes the need to
lock the hci_dev. Passing the SMP context instead of just the crypto
handle allows a bit more detailed logging which is helpful in
multi-adapter scenarios.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Many places have to be extra careful to not hold the hdev lock when
calling into the SMP code. This is because the SMP crypto functions use
the crypto handle that's part of the hci_dev struct. Giving the SMP
context its own handle helps simplifying the locking logic and removes
the risk for deadlocks.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hdev lock must be held before calling into smp_distribute_keys. Also
things such as hci_add_irk() require the lock. This patch fixes the
issue by adding the necessary locking into the smp_cmd_ident_addr_info
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the link_mode member of the hci_conn struct is a bit field and we
already have a flags member as well it makes sense to merge these two
together. This patch moves all used link_mode bits into corresponding
flags. To keep backwards compatibility with user space we still need to
provide a get_link_mode() helper function for the ioctl's that expect a
link_mode style value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The ssp_debug_mode debugfs option for developers is no longer
needed. Support for using Secure Simple Pairing (SSP) debug
mode is exposed by the management interface now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds a new valid mode 0x02 for the mgmt_set_debug_keys
command. The 0x02 mode sets the HCI_USE_DEBUG_KEYS flag which makes us
always use debug keys for pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To pave the way for actively using debug keys for pairing this patch
adds a new HCI_USE_DEBUG_KEYS flag for the purpose. When the flag is set
we issue a HCI_Write_SSP_Debug mode whenever HCI_Write_SSP_Mode(0x01)
has been issued as well as before issuing a HCI_Write_SSP_Mode(0x00)
command.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We should never allow user space to feed back debug keys to the kernel.
If the user desires to use debug keys require setting the appropriate
debug keys mode and performing a new pairing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no point in having boolean variables in the hci_conn struct
since it already has a flags member. This patch converts the flush_key
member into a proper flag.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of waiting for a disconnection to occur to remove a debug key
simply never store it in the list to begin with. This means we can also
remove the debug keys check when looking up keys in
hci_link_key_request_evt().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We're planning to add a flag to actively use debug keys in addition to
simply just accepting them, which makes the current generically named
DEBUG_KEYS flag a bit confusing. Since the flag in practice affects
whether the kernel keeps debug keys around or not rename it to
HCI_KEEP_DEBUG_KEYS.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There are two callers of hci_add_link_key(). The first one is the HCI
Link Key Notification event and the second one the mgmt code that
receives a list of link keys from user space. Previously we've had the
hci_add_link_key() function being responsible for also emitting a mgmt
signal but for the latter use case this should not happen. Because of
this a rather awkward new_key paramter has been passed to the function.
This patch moves the mgmt event sending out from the hci_add_link_key()
function, thereby making the code a bit more understandable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
By returning the added (or updated) key we pave the way for further
refactoring (in subsequent patches) that allows moving the mgmt event
sending out from this function (and thereby removal of the awkward
new_key parameter).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the current LE connection parameters of a slave connection do not
match up with the controller defined values, then trigger the connection
update procedure to allow adjusting them.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For all incoming LE connections, the minimum and maximum connection
interval is a value that should be copied from the controller default
values. This allows to properly check if the resulting connection
interval of a newly established connection is in the range we are
expecting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the LE controller changes its connection parameters, it will send
a connection parameter update event. Make sure that the new set of
parameters are stored in hci_conn struct and thus will properly update
the previous values retrieved from the connection complete event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The LE connection parameters are needed later on to be able to decide
if it is required to trigger connection update procedures. So when the
connection has been established successfully, store the current used
parameters in hci_conn struct.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the module is unloaded, unregister the network device
so that the system does not try to access non-existing device.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Count how many 6LoWPAN connections there exists so that we
do not unload the module if there are still connections alive.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Instead of adding the 6LoWPAN functionality to Bluetooth module,
we create a separate kernel module for it.
Usage:
In the slave side do this:
$ modprobe bluetooth_6lowpan
$ echo 62 > /sys/kernel/debug/bluetooth/6lowpan_psm
$ hciconfig hci0 leadv
In the master side do this:
$ modprobe bluetooth_6lowpan
$ echo 62 > /sys/kernel/debug/bluetooth/6lowpan_psm
$ echo 'connect E0:06:E6:B7:2A:73 1' > \
/sys/kernel/debug/bluetooth/6lowpan_control
The 6LoWPAN functionality can be controlled by psm value. If it
is left to 0, then the module is disabled and all the 6LoWPAN
connections are dropped if there were any. In the above example,
the psm value is just an example and not a real value for
6LoWPAN service. The real psm value is yet to be defined in
Bluetooth specification.
The 6lowpan controlling interface is a temporary solution
until the specifications are ready.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Create a CoC dynamically instead of one fixed channel for communication
to peer devices.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The highly optimized TX path for L2CAP channels and its fragmentation
within the HCI ACL packets requires to copy data from user provided
IO vectors and also kernel provided memory buffers.
This patch allows channel clients to provide a memcpy_fromiovec callback
to keep this optimized behavior, but adapt it to kernel vs user memory
for the TX path. For all kernel internal L2CAP channels, a default
implementation is provided that can be referenced.
In case of A2MP, this fixes a long-standing issue with wrongly accessing
kernel memory as user memory.
This patch originally by Marcel Holtmann.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All the special settings configured via debugfs are either developer
only options or temporary solutions. To not clutter the standard flags,
move them to their own dbg_flags entry.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the rename of STK_SLAVE to simply STK happened we missed this place
in the ltk_type_master function. Now, checking for master is as simple
as checking whether the type is SMP_LTK. The helper function is kept
around for better readability in the (right now three) callers and for
simpler extension with new key types in the future.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The valid range of IO capabilities for the Set IO Capability and Pair
Device mgmt commands is 0-4 (4 being the KeyboarDisplay capability for
SMP). We should return an invalid parameters error if user space gives
us a value outside of this range.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the SMP code needs to swap ordering of variable length buffers add
a convenience function that can be used for any length buffer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no reason to have explicit values for these flags. Convert them
to an enum to be consistent with other similar flags.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The LTK type has really nothing to do with HCI so it makes more sense to
have these in smp.h than hci.h. This patch moves the defines to smp.h
and removes the HCI_ prefix in the same go.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We never store the "master" type of STKs since we request encryption
directly with them so we only need one STK type (the one that's
looked-up on the slave side). Simply remove the unnecessary define and
rename the _SLAVE one to the shorter form.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The smp_chan_create function may return NULL, e.g. in the case of memory
allocation failure, so we always need to check for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the whole HCI command, event and data packet processing has been
migrated to use workqueues instead of tasklets, it makes sense to use
struct delayed_work instead of struct timer_list for the timeout
handling. This patch converts the hdev->cmd_timer to use workqueue
as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When allocating the L2CAP SKB for transmission, provide the upper layers
with a clear distinction on what is the header and what is the body
portion of the SKB.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SKB for L2CAP sockets are all allocated in a central callback
in the socket support. Instead of having to pass around the socket
priority all the time, assign it to skb->priority when actually
allocating the SKB.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The struct l2cap_ops field should not allow any modifications and thus
it is better declared as const.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Only warn if the value is written to alpha or beta. We don't care
emitting a one-time warning when only reading it.
Reported-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4960, section 8.3 says:
On an idle destination address that is allowed to heartbeat,
it is recommended that a HEARTBEAT chunk is sent once per RTO
of that destination address plus the protocol parameter
'HB.interval', with jittering of +/- 50% of the RTO value,
and exponential backoff of the RTO if the previous HEARTBEAT
is unanswered.
Currently, we calculate jitter via sctp_jitter() function first,
and then add its result to the current RTO for the new timeout:
TMO = RTO + (RAND() % RTO) - (RTO / 2)
`------------------------^-=> sctp_jitter()
Instead, we can just simplify all this by directly calculating:
TMO = (RTO / 2) + (RAND() % RTO)
With the help of prandom_u32_max(), we don't need to open code
our own global PRNG, but can instead just make use of the per
CPU implementation of prandom with better quality numbers. Also,
we can now spare us the conditional for divide by zero check
since no div or mod operation needs to be used. Note that
prandom_u32_max() won't emit the same result as a mod operation,
but we really don't care here as we only want to have a random
number scaled into RTO interval.
Note, exponential RTO backoff is handeled elsewhere, namely in
sctp_do_8_2_transport_strike().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in repair-mode and TCP_RECV_QUEUE is set, we end up calling
tcp_push with mss_now being 0. If data is in the send-queue and
tcp_set_skb_tso_segs gets called, we crash because it will divide by
mss_now:
[ 347.151939] divide error: 0000 [#1] SMP
[ 347.152907] Modules linked in:
[ 347.152907] CPU: 1 PID: 1123 Comm: packetdrill Not tainted 3.16.0-rc2 #4
[ 347.152907] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 347.152907] task: f5b88540 ti: f3c82000 task.ti: f3c82000
[ 347.152907] EIP: 0060:[<c1601359>] EFLAGS: 00210246 CPU: 1
[ 347.152907] EIP is at tcp_set_skb_tso_segs+0x49/0xa0
[ 347.152907] EAX: 00000b67 EBX: f5acd080 ECX: 00000000 EDX: 00000000
[ 347.152907] ESI: f5a28f40 EDI: f3c88f00 EBP: f3c83d10 ESP: f3c83d00
[ 347.152907] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 347.152907] CR0: 80050033 CR2: 083158b0 CR3: 35146000 CR4: 000006b0
[ 347.152907] Stack:
[ 347.152907] c167f9d9 f5acd080 000005b4 00000002 f3c83d20 c16013e6 f3c88f00 f5acd080
[ 347.152907] f3c83da0 c1603b5a f3c83d38 c10a0188 00000000 00000000 f3c83d84 c10acc85
[ 347.152907] c1ad5ec0 00000000 00000000 c1ad679c 010003e0 00000000 00000000 f3c88fc8
[ 347.152907] Call Trace:
[ 347.152907] [<c167f9d9>] ? apic_timer_interrupt+0x2d/0x34
[ 347.152907] [<c16013e6>] tcp_init_tso_segs+0x36/0x50
[ 347.152907] [<c1603b5a>] tcp_write_xmit+0x7a/0xbf0
[ 347.152907] [<c10a0188>] ? up+0x28/0x40
[ 347.152907] [<c10acc85>] ? console_unlock+0x295/0x480
[ 347.152907] [<c10ad24f>] ? vprintk_emit+0x1ef/0x4b0
[ 347.152907] [<c1605716>] __tcp_push_pending_frames+0x36/0xd0
[ 347.152907] [<c15f4860>] tcp_push+0xf0/0x120
[ 347.152907] [<c15f7641>] tcp_sendmsg+0xf1/0xbf0
[ 347.152907] [<c116d920>] ? kmem_cache_free+0xf0/0x120
[ 347.152907] [<c106a682>] ? __sigqueue_free+0x32/0x40
[ 347.152907] [<c106a682>] ? __sigqueue_free+0x32/0x40
[ 347.152907] [<c114f0f0>] ? do_wp_page+0x3e0/0x850
[ 347.152907] [<c161c36a>] inet_sendmsg+0x4a/0xb0
[ 347.152907] [<c1150269>] ? handle_mm_fault+0x709/0xfb0
[ 347.152907] [<c15a006b>] sock_aio_write+0xbb/0xd0
[ 347.152907] [<c1180b79>] do_sync_write+0x69/0xa0
[ 347.152907] [<c1181023>] vfs_write+0x123/0x160
[ 347.152907] [<c1181d55>] SyS_write+0x55/0xb0
[ 347.152907] [<c167f0d8>] sysenter_do_call+0x12/0x28
This can easily be reproduced with the following packetdrill-script (the
"magic" with netem, sk_pacing and limit_output_bytes is done to prevent
the kernel from pushing all segments, because hitting the limit without
doing this is not so easy with packetdrill):
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1460>
+0 > S. 0:0(0) ack 1 <mss 1460>
+0.1 < . 1:1(0) ack 1 win 65000
+0 accept(3, ..., ...) = 4
// This forces that not all segments of the snd-queue will be pushed
+0 `tc qdisc add dev tun0 root netem delay 10ms`
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=2`
+0 setsockopt(4, SOL_SOCKET, 47, [2], 4) = 0
+0 write(4,...,10000) = 10000
+0 write(4,...,10000) = 10000
// Set tcp-repair stuff, particularly TCP_RECV_QUEUE
+0 setsockopt(4, SOL_TCP, 19, [1], 4) = 0
+0 setsockopt(4, SOL_TCP, 20, [1], 4) = 0
// This now will make the write push the remaining segments
+0 setsockopt(4, SOL_SOCKET, 47, [20000], 4) = 0
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=130000`
// Now we will crash
+0 write(4,...,1000) = 1000
This happens since ec34232575 (tcp: fix retransmission in repair
mode). Prior to that, the call to tcp_push was prevented by a check for
tp->repair.
The patch fixes it, by adding the new goto-label out_nopush. When exiting
tcp_sendmsg and a push is not required, which is the case for tp->repair,
we go to this label.
When repairing and calling send() with TCP_RECV_QUEUE, the data is
actually put in the receive-queue. So, no push is required because no
data has been added to the send-queue.
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Fixes: ec34232575 (tcp: fix retransmission in repair mode)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Andrew Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
based on checkpatch:
"debugfs_remove_recursive(NULL) is safe this check is probably not required"
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-06-27
Please pull the following batch of fixes for the 3.16 stream...
For the mac80211 bits, Johannes says:
"We have a fix from Eliad for a time calculation, a fix from Max for
head/tailroom when sending authentication packets, a revert that Felix
requested since the patch in question broke regulatory and a fix from
myself for an issue with a new command that we advertised in the wrong
place."
For the bluetooth bits, Gustavo says:
"A few fixes for 3.16. This pull request contains a NULL dereference fix,
and some security/pairing fixes."
For the iwlwifi bits, Emmanuel says:
"I have here a fix from Eliad for scheduled scan: it fixes a firmware
assertion. Arik reverts a patch I made that didn't take into account
that 3160 doesn't have UAPSD and hence, we can't assume that all
newer firmwares support the feature. Here too, the visible effect
is a firmware assertion. Along with that, we have a few fixes and
additions to the device list."
For the ath10k bits, Kalle says:
"Bartosz fixed an issue where we were not able to create 8 vdevs when
using DFS. Michal removed a false warning which was just confusing
people."
On top of that...
Arend van Spriel fixes a 'divide by zero' regression in brcmfmac.
Amitkumar Karwar corrects a transmit timeout in mwifiex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When an UDP application switches from AF_INET to AF_INET6 sockets, we
have a small performance degradation for IPv4 communications because of
extra cache line misses to access ipv6only information.
This can also be noticed for TCP listeners, as ipv6_only_sock() is also
used from __inet_lookup_listener()->compute_score()
This is magnified when SO_REUSEPORT is used.
Move ipv6only into struct sock_common so that it is available at
no extra cost in lookups.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The if_lock()/if_unlock() in next_to_run() adds a significant
overhead, because its called for every packet in busy loop of
pktgen_thread_worker(). (Thomas Graf originally pointed me
at this lock problem).
Removing these two "LOCK" operations should in theory save us approx
16ns (8ns x 2), as illustrated below we do save 16ns when removing
the locks and introducing RCU protection.
Performance data with CLONE_SKB==100000, TX-size=512, rx-usecs=30:
(single CPU performance, ixgbe 10Gbit/s, E5-2630)
* Prev : 5684009 pps --> 175.93ns (1/5684009*10^9)
* RCU-fix: 6272204 pps --> 159.43ns (1/6272204*10^9)
* Diff : +588195 pps --> -16.50ns
To understand this RCU patch, I describe the pktgen thread model
below.
In pktgen there is several kernel threads, but there is only one CPU
running each kernel thread. Communication with the kernel threads are
done through some thread control flags. This allow the thread to
change data structures at a know synchronization point, see main
thread func pktgen_thread_worker().
Userspace changes are communicated through proc-file writes. There
are three types of changes, general control changes "pgctrl"
(func:pgctrl_write), thread changes "kpktgend_X"
(func:pktgen_thread_write), and interface config changes "etcX@N"
(func:pktgen_if_write).
Userspace "pgctrl" and "thread" changes are synchronized via the mutex
pktgen_thread_lock, thus only a single userspace instance can run.
The mutex is taken while the packet generator is running, by pgctrl
"start". Thus e.g. "add_device" cannot be invoked when pktgen is
running/started.
All "pgctrl" and all "thread" changes, except thread "add_device",
communicate via the thread control flags. The main problem is the
exception "add_device", that modifies threads "if_list" directly.
Fortunately "add_device" cannot be invoked while pktgen is running.
But there exists a race between "rem_device_all" and "add_device"
(which normally don't occur, because "rem_device_all" waits 125ms
before returning). Background'ing "rem_device_all" and running
"add_device" immediately allow the race to occur.
The race affects the threads (list of devices) "if_list". The if_lock
is used for protecting this "if_list". Other readers are given
lock-free access to the list under RCU read sections.
Note, interface config changes (via proc) can occur while pktgen is
running, which worries me a bit. I'm assuming proc_remove() takes
appropriate locks, to assure no writers exists after proc_remove()
finish.
I've been running a script exercising the race condition (leading me
to fix the proc_remove order), without any issues. The script also
exercises concurrent proc writes, while the interface config is
getting removed.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling set_current_state() inside the busy-loop in
pktgen_thread_worker(). In case of pkt_dev->delay, then it is still
used/enabled in pktgen_xmit() via the spin() call.
The set_current_state(TASK_INTERRUPTIBLE) uses a xchg, which implicit
is LOCK prefixed. I've measured the asm LOCK operation to take approx
8ns on this E5-2630 CPU. Performance increase corrolate with this
measurement.
Performance data with CLONE_SKB==100000, rx-usecs=30:
(single CPU performance, ixgbe 10Gbit/s, E5-2630)
* Prev: 5454050 pps --> 183.35ns (1/5454050*10^9)
* Now: 5684009 pps --> 175.93ns (1/5684009*10^9)
* Diff: +229959 pps --> -7.42ns
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This stub now allows userspace to see IFLA_INFO_KIND for ovs master and
IFLA_INFO_SLAVE_KIND for slave.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, it is assumed that ops->setup is filled up. But there might be
case that ops might make sense even without ->setup. In that case,
forbid to newlink and dellink.
This allows to register simple rtnl link ops containing only ->kind.
That allows consistent way of passing device kind (either device-kind or
slave-kind) to userspace.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 371121057607e3127e19b3fa094330181b5b031e("net:
QDISC_STATE_RUNNING dont need atomic bit ops") the
__QDISC_STATE_RUNNING is renamed to __QDISC___STATE_RUNNING,
but the old names existing in comment are not replaced with
the new name completely.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can be used in virtual networking applications, and
may have other uses as well. The option is disabled by
default.
A specific use case is setting up virtual routers, bridges, and
hosts on a single OS without the use of network namespaces or
virtual machines. With proper use of ip rules, routing tables,
veth interface pairs and/or other virtual interfaces,
and applications that can bind to interfaces and/or IP addresses,
it is possibly to create one or more virtual routers with multiple
hosts attached. The host interfaces can act as IPv6 systems,
with radvd running on the ports in the virtual routers. With the
option provided in this patch enabled, those hosts can now properly
obtain IPv6 addresses from the radvd.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is disabled by default, just like similar debug info
already in this module. But, makes it easier to find out
why RA is not being accepted when debugging strange behaviour.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have two different ways to handle changes to sk->sk_dst
First way (used by TCP) assumes socket lock is owned by caller, and use
no extra lock : __sk_dst_set() & __sk_dst_reset()
Another way (used by UDP) uses sk_dst_lock because socket lock is not
always taken. Note that sk_dst_lock is not softirq safe.
These ways are not inter changeable for a given socket type.
ipv4_sk_update_pmtu(), added in linux-3.8, added a race, as it used
the socket lock as synchronization, but users might be UDP sockets.
Instead of converting sk_dst_lock to a softirq safe version, use xchg()
as we did for sk_rx_dst in commit e47eb5dfb2 ("udp: ipv4: do not use
sk_dst_lock from softirq context")
In a follow up patch, we probably can remove sk_dst_lock, as it is
only used in IPv6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Fixes: 9cb3a50c5f ("ipv4: Invalidate the socket cached route on pmtu events if possible")
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the race condition in userspace, there is chance that two
overlapping megaflows could be installed in datapath. And this
causes userspace unable to delete the less inclusive megaflow flow
even after it timeout, since the flow_del logic will stop at the
first match of masked flow.
This commit fixes the bug by making the kernel flow_del and flow_get
logic check all masks in that case.
Introduced by 03f0d916a (openvswitch: Mega flow implementation).
Signed-off-by: Alex Wang <alexw@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Fixes build error introduced by commit 1fb6f159fd (tcp: add
tcp_conn_request):
net/ipv4/tcp_input.c: In function 'pr_drop_req':
net/ipv4/tcp_input.c:5889:130: error: 'struct sock_common' has no member named 'skc_v6_daddr'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow statistics need to take into account the TCP flags from the packet
currently being processed (in 'key'), not the TCP flags matched by the
flow found in the kernel flow table (in 'flow').
This bug made the Open vSwitch userspace fin_timeout action have no effect
in many cases.
This bug is introduced by commit 88d73f6c41 (openvswitch: Use
TCP flags in the flow key for stats.)
Reported-by: Len Gao <leng@vmware.com>
Signed-off-by: Ben Pfaff <blp@nicira.com>
Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
When use gre vport, openvswitch register a gre_cisco_protocol but
does not supply a err_handler with it. The gre_cisco_err() in
net/ipv4/gre_demux.c expect err_handler be provided with the
gre_cisco_protocol implementation, and call ->err_handler() without
existence check, cause the kernel crash.
This patch provide a err_handler to fix this bug.
This bug introduced by commit aa310701e7 (openvswitch: Add gre
tunnel support.)
Signed-off-by: Wei Zhang <asuka.com@163.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
When sample action returns with an error, the skb has already been
freed. This patch fix a bug to make sure we don't free it again.
This bug introduced by commit ccb1352e76 (net: Add Open vSwitch
kernel components.)
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time around. The highlights include:
- iscsi-target CHAP authentication fixes to enforce explicit key
values (Tejas Vaykole + rahul.rane)
- fix a long-standing OOPs in target-core when a alua configfs
attribute is accessed after port symlink has been removed.
(Sebastian Herbszt)
- fix a v3.10.y iscsi-target regression causing the login reject
status class/detail to be ignored (Christoph Vu-Brugier)
- fix a v3.10.y iscsi-target regression to avoid rejecting an
existing ITT during Data-Out when data-direction is wrong (Santosh
Kulkarni + Arshad Hussain)
- fix a iscsi-target related shutdown deadlock on UP kernels (Mikulas
Patocka)
- fix a v3.16-rc1 build issue with vhost-scsi + !CONFIG_NET (MST)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: fix iscsit_del_np deadlock on unload
iovec: move memcpy_from/toiovecend to lib/iovec.c
iscsi-target: Avoid rejecting incorrect ITT for Data-Out
tcm_loop: Fix memory leak in tcm_loop_submission_work error path
iscsi-target: Explicily clear login response PDU in exception path
target: Fix left-over se_lun->lun_sep pointer OOPs
iscsi-target; Enforce 1024 byte maximum for CHAP_C key value
iscsi-target: Convert chap_server_compute_md5 to use kstrtoul
Create tcp_conn_request and remove most of the code from
tcp_v4_conn_request and tcp_v6_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add queue_add_hash member to tcp_request_sock_ops so that we can later
unify tcp_v4_conn_request and tcp_v6_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mss_clamp member to tcp_request_sock_ops so that we can later
unify tcp_v4_conn_request and tcp_v6_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new tcp_request_sock_ops method to unify the IPv4/IPv6
signature for tcp_v[46]_send_synack. This allows us to later unify
tcp_v4_rtx_synack with tcp_v6_rtx_synack and tcp_v4_conn_request with
tcp_v4_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More work in preparation of unifying tcp_v4_conn_request and
tcp_v6_conn_request: indirect the init sequence calls via the
tcp_request_sock_ops.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the tcp_v6_conn_request calls flow similar with that of
tcp_v4_conn_request.
Note that want_cookie can be true only if isn is zero and that is why
we can move the if (want_cookie) block out of the if (!isn) block.
Moving security_inet_conn_request() has a couple of side effects:
missing inet_rsk(req)->ecn_ok update and the req->cookie_ts
update. However, neither SELinux nor Smack security hooks seems to
check them. This change should also avoid future different behaviour
for IPv4 and IPv6 in the security hooks.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create wrappers with same signature for the IPv4/IPv6 request routing
calls and use these wrappers (via route_req method from
tcp_request_sock_ops) in tcp_v4_conn_request and tcp_v6_conn_request
with the purpose of unifying the two functions in a later patch.
We can later drop the wrapper functions and modify inet_csk_route_req
and inet6_cks_route_req to use the same signature.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the specific IPv4/IPv6 cookie sequence initialization to a new
method in tcp_request_sock_ops in preparation for unifying
tcp_v4_conn_request and tcp_v6_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the specific IPv4/IPv6 intializations to a new method in
tcp_request_sock_ops in preparation for unifying tcp_v4_conn_request
and tcp_v6_conn_request.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since pktops is only used for IPv6 only and opts is used for IPv4
only, we can move these fields into a union and this allows us to drop
the inet6_reqsk_alloc function as after this change it becomes
equivalent with inet_reqsk_alloc.
This patch also fixes a kmemcheck issue in the IPv6 stack: the flags
field was not annotated after a request_sock was allocated.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 016818d07 (tcp: TCP Fast Open Server - take SYNACK RTT after
completing 3WHS) changes the code to only take a snt_synack timestamp
when a SYNACK transmit or retransmit succeeds. This behaviour is later
broken by commit 843f4a55e (tcp: use tcp_v4_send_synack on first
SYN-ACK), as snt_synack is now updated even if tcp_v4_send_synack
fails.
Also, commit 3a19ce0ee (tcp: IPv6 support for fastopen server) misses
the required IPv6 updates for 016818d07.
This patch makes sure that snt_synack is updated only when the SYNACK
trasnmit/retransmit succeeds, for both IPv4 and IPv6.
Cc: Cardwell <ncardwell@google.com>
Cc: Daniel Lee <longinus00@gmail.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a consequence of the recently introduced serialized access
to the socket in commit 8d94168a761819d10252bab1f8de6d7b202c3baa
("tipc: same receive code path for connection protocol and data
messages") we can make a number of simplifications in the
detection and handling of connection congestion situations.
- We don't need to keep two counters, one for sent messages and one
for acked messages. There is no longer any risk for races between
acknowledge messages arriving in BH and data message sending
running in user context. So we merge this into one counter,
'sent_unacked', which is incremented at sending and subtracted
from at acknowledge reception.
- We don't need to set the 'congested' field in tipc_port to
true before we sent the message, and clear it when sending
is successful. (As a matter of fact, it was never necessary;
the field was set in link_schedule_port() before any wakeup
could arrive anyway.)
- We keep the conditions for link congestion and connection connection
congestion separated. There would otherwise be a risk that an arriving
acknowledge message may wake up a user sleeping because of link
congestion.
- We can simplify reception of acknowledge messages.
We also make some cosmetic/structural changes:
- We rename the 'congested' field to the more correct 'link_cong´.
- We rename 'conn_unacked' to 'rcv_unacked'
- We move the above mentioned fields from struct tipc_port to
struct tipc_sock.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simplify the code for receiving connection probes, leveraging the
recently introduced tipc_msg_reverse() function. We also stick to
the principle of sending a possible response message directly from
the calling (tipc_sk_rcv or backlog_rcv) functions, hence making
the call chain shallower and easier to follow.
We make one small protocol change here, allowed according to
the spec. If a protocol message arrives from a remote socket that
is not the one we are connected to, we are currently generating a
connection abort message and send it to the source. This behavior
is unnecessary, and might even be a security risk, so instead we
now choose to only ignore the message. The consequnce for the sender
is that he will need longer time to discover his mistake (until the
next timeout), but this is an extreme corner case, and may happen
anyway under other circumstances, so we deem this change acceptable.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation to eliminate port_lock we need to bring reception
of connection protocol messages under proper protection of bh_lock_sock
or socket owner.
We fix this by letting those messages follow the same code path as
incoming data messages.
As a side effect of this change, the last reference to the function
net_route_msg() disappears, and we can eliminate that function.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several functions in port.c, related to the port protocol and
connection shutdown, need to send messages. We now convert them
to use the new link send function.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We move the message sending across established connections
to use the message preparation and send functions introduced
earlier in this series. We now do the message preparation
and call to the link send function directly from the socket,
instead of going via the port layer.
As a consequence of this change, the functions tipc_send(),
tipc_port_iovec_rcv(), tipc_port_iovec_reject() and tipc_reject_msg()
become unreferenced and can be eliminated from port.c. For the same
reason, the functions tipc_link_xmit_fast(), tipc_link_iovec_xmit_long()
and tipc_link_iovec_fast() can be eliminated from link.c.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We merge the code for sending port name and port identity addressed
messages into the corresponding send functions in socket.c, and start
using the new fragmenting and transmit functions we just have introduced.
This saves a call level and quite a few code lines, as well as making
this part of the code easier to follow. As a consequence, the functions
tipc_send2name() and tipc_send2port() in port.c can be removed.
For practical reasons, we break out the code for sending multicast messages
from tipc_sendmsg() and move it into a separate function, tipc_sendmcast(),
but we do not yet convert it into using the new build/send functions.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a message arrives in a node and finds no destination
socket, we may need to drop it, reject it, or forward it after
a secondary destination lookup. The latter two cases currently
results in a code path that is perceived as complex, because it
follows a deep call chain via obscure functions such as
net_route_named_msg() and net_route_msg().
We now introduce a function, tipc_msg_eval(), that takes the
decision about whether such a message should be rejected or
forwarded, but leaves it to the caller to actually perform
the indicated action.
If the decision is 'reject', it is still the task of the recently
introduced function tipc_msg_reverse() to take the final decision
about whether the message is rejectable or not. In the latter case
it drops the message.
As a result of this change, we can finally eliminate the function
net_route_named_msg(), and hence become independent of net_route_msg().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The way we build and send rejected message is currenty perceived as
hard to follow, partly because we let the transmission go via deep
call chains through functions such as tipc_reject_msg() and
net_route_msg().
We want to remove those functions, and make the call sequences shallower
and simpler. For this purpose, we separate building and sending of
rejected messages. We build the reject message using the new function
tipc_msg_reverse(), and let the transmission go via the newly introduced
tipc_link_xmit2() function, as all transmission eventually will do. We
also ensure that all calls to tipc_link_xmit2() are made outside
port_lock/bh_lock_sock.
Finally, we replace all calls to tipc_reject_msg() with the two new
calls at all locations in the code that we want to keep. The remaining
calls are made from code that we are planning to remove, along with
tipc_reject_msg() itself.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fragmentation at message sending is currently performed in two
places in link.c, depending on whether data to be transmitted
is delivered in the form of an iovec or as a big sk_buff. Those
functions are also tightly entangled with the send functions
that are using them.
We now introduce a re-entrant, standalone function, tipc_msg_build2(),
that builds a packet chain directly from an iovec. Each fragment is
sized according to the MTU value given by the caller, and is prepended
with a correctly built fragment header, when needed. The function is
independent from who is calling and where the chain will be delivered,
as long as the caller is able to indicate a correct MTU.
The function is tested, but not called by anybody yet. Since it is
incompatible with the existing tipc_msg_build(), and we cannot yet
remove that function, we have given it a temporary name.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Message fragmentation is currently performed at link level, inside
the protection of node_lock. This potentially binds up the sending
link structure for a long time, instead of letting it do other tasks,
such as handle reception of new packets.
In this commit, we make the MTUs of each active link become easily
accessible from the socket level, i.e., without taking any spinlock
or dereferencing the target link pointer. This way, we make it possible
to perform fragmentation in the sending socket, before sending the
whole fragment chain to the link for transport.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current link implementation provides several different transmit
functions, depending on the characteristics of the message to be
sent: if it is an iovec or an sk_buff, if it needs fragmentation or
not, if the caller holds the node_lock or not. The permutation of
these options gives us an unwanted amount of unnecessarily complex
code.
As a first step towards simplifying the send path for all messages,
we introduce two new send functions at link level, tipc_link_xmit2()
and __tipc_link_xmit2(). The former looks up a link to the message
destination, and if one is found, it grabs the node lock and calls
the second function, which works exclusively inside the node lock
protection. If no link is found, and the destination is on the same
node, it delivers the message directly to the local destination
socket.
The new functions take a buffer chain where all packet headers are
already prepared, and the correct MTU has been used. These two
functions will later replace all other link-level transmit functions.
The functions are not backwards compatible, so we have added them
as new functions with temporary names. They are tested, but have no
users yet. Those will be added later in this series.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some places, TIPC functions returns positive integers as return
codes. This goes against standard Linux coding practice, and may
even cause problems in some cases.
We now change the return values of the functions filter_rcv()
and filter_connect() to become signed integers, and return
negative error codes when needed. The codes we use in these
particular cases are still TIPC specific, since they are both
part of the TIPC API and have no correspondence in errno.h
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the function tipc_nodesub_notify() we call a function pointer
aggregated into the object to be notified, whereafter we set
the function pointer to NULL. However, in some cases the function
pointed to will free the struct containing the function pointer,
resulting in a write to already freed memory.
This bug seems to always have been there, without causing any
notable harm.
In this commit we fix the problem by inverting the order of the
zeroing and the function call.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ERROR: "memcpy_fromiovecend" [drivers/vhost/vhost_scsi.ko] undefined!
commit 9f977ef7b6
vhost-scsi: Include prot_bytes into expected data transfer length
in target-pending makes drivers/vhost/scsi.c call memcpy_fromiovecend().
This function is not available when CONFIG_NET is not enabled.
socket.h already includes uio.h, so no callers need updating.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Based on RFC3810 6.2, we also need to check the hop limit and router alert
option besides source address.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MIB counters for rcvbuferrors in UDP to help diagnose problems.
Signed-off-by: James M Leddy <james.leddy@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix crash in ipvs tot_stats estimator, from Julian Anastasov.
2) Fix OOPS in nf_nat on netns removal, from Florian Westphal.
3) Really really really fix locking issues in slip and slcan tty write
wakeups, from Tyler Hall.
4) Fix checksum offloading in fec driver, from Fugang Duan.
5) Off by one in BPF instruction limit test, from Kees Cook.
6) Need to clear all TSO capability flags when doing software TSO in
tg3 driver, from Prashant Sreedharan.
7) Fix memory leak in vlan_reorder_header() error path, from Li
RongQing.
8) Fix various bugs in xen-netfront and xen-netback multiqueue support,
from David Vrabel and Wei Liu.
9) Fix deadlock in cxgb4 driver, from Li RongQing.
10) Prevent double free of no-cache DST entries, from Eric Dumazet.
11) Bad csum_start handling in skb_segment() leads to crashes when
forwarding, from Tom Herbert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: fix setting csum_start in skb_segment()
ipv4: fix dst race in sk_dst_get()
net: filter: Use kcalloc/kmalloc_array to allocate arrays
trivial: net: filter: Change kerneldoc parameter order
trivial: net: filter: Fix typo in comment
net: allwinner: emac: Add missing free_irq
cxgb4: use dev_port to identify ports
xen-netback: bookkeep number of active queues in our own module
tg3: Change nvram command timeout value to 50ms
cxgb4: Not need to hold the adap_rcu_lock lock when read adap_rcu_list
be2net: fix qnq mode detection on VFs
of: mdio: fixup of_phy_register_fixed_link parsing of new bindings
at86rf230: fix irq setup
net: phy: at803x: fix coccinelle warnings
net/mlx4_core: Fix the error flow when probing with invalid VF configuration
tulip: Poll link status more frequently for Comet chips
net: huawei_cdc_ncm: increase command buffer size
drivers: net: cpsw: fix dual EMAC stall when connected to same switch
xen-netfront: recreate queues correctly when reconnecting
xen-netfront: fix oops when disconnected from backend
...
Dave Jones reported that a crash is occurring in
csum_partial
tcp_gso_segment
inet_gso_segment
? update_dl_migration
skb_mac_gso_segment
__skb_gso_segment
dev_hard_start_xmit
sch_direct_xmit
__dev_queue_xmit
? dev_hard_start_xmit
dev_queue_xmit
ip_finish_output
? ip_output
ip_output
ip_forward_finish
ip_forward
ip_rcv_finish
ip_rcv
__netif_receive_skb_core
? __netif_receive_skb_core
? trace_hardirqs_on
__netif_receive_skb
netif_receive_skb_internal
napi_gro_complete
? napi_gro_complete
dev_gro_receive
? dev_gro_receive
napi_gro_receive
It looks like a likely culprit is that SKB_GSO_CB()->csum_start is
not set correctly when doing non-scatter gather. We are using
offset as opposed to doffset.
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 7e2b10c1e5 ("net: Support for multiple checksums with gso")
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IP route cache had been removed in linux-3.6, we broke assumption
that dst entries were all freed after rcu grace period. DST_NOCACHE
dst were supposed to be freed from dst_release(). But it appears
we want to keep such dst around, either in UDP sockets or tunnels.
In sk_dst_get() we need to make sure dst refcount is not 0
before incrementing it, or else we might end up freeing a dst
twice.
DST_NOCACHE set on a dst does not mean this dst can not be attached
to a socket or a tunnel.
Then, before actual freeing, we need to observe a rcu grace period
to make sure all other cpus can catch the fact the dst is no longer
usable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dormando <dormando@rydia.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kcalloc/kmalloc_array to make it clear we're allocating arrays. No
integer overflow can actually happen here, since len/flen is guaranteed
to be less than BPF_MAXINSNS (4096). However, this changed makes sure
we're not going to get one if BPF_MAXINSNS were ever increased.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the order of the parameters to sk_unattached_filter_create() in
the kerneldoc to reflect the order they appear in the actual function.
This fix is only cosmetic, in the generated doc they still appear in the
correct order without the fix.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems overkill to use vmalloc() for typical listeners with less than
2048 hash buckets. Try kmalloc() and fallback to vmalloc() to reduce TLB
pressure.
Use kvfree() helper as it is now available.
Use ilog2() instead of a loop.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: netdev@vger.kernel.org
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver is now responsible for veryfing if the
switch is possible.
Since this is inherently tricky driver may decide
to disconnect an interface later with
cfg80211_stop_iface().
This doesn't mean driver can accept everything. It
should do it's best to verify requests and reject
them as soon as possible.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel switch finalization is now 2-step. First
step is when driver calls chswitch_done(), the
other is when reservation is actually finalized
(which be defered for in-place reservation).
It is now safe to call ieee80211_chswitch_done()
more than once.
Also remove the ieee80211_vif_change_channel()
because it is no longer used.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel switch finalization is now 2-step. First
step is when driver calls csa_finish(), the other
is when reservation is actually finalized (which
can be deferred for in-place reservation).
It is now safe to call ieee80211_csa_finish() more
than once.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_check_combinations() computes
radar_detect accordingly depending on chanctx
reservation status.
This makes it possible to use the function for
channel_switch validation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Multi-vif in-place reservations happen when
it is impossible to allocate more channel contexts
as indicated by interface combinations.
Such reservations are not finalized until all
assigned interfaces are ready.
This still doesn't handle all possible cases
(i.e. degradation of number of channels) properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split sched scan IEs to band specific and not band specific
blocks. Common IEs blocks may be sent to the FW once per command,
instead of per band.
This allows optimization of size of the command, which may be
required by some drivers (eg. iwlmvm with newer firmware version).
As this changes the mac80211 API, update all drivers to use the
new version correctly, even if they don't (yet) make use of the
split data.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.
As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix nfs4_negotiate_security to create an rpc_clnt used to test each SECINFO
returned pseudoflavor. Check credential creation (and gss_context creation)
which is important for RPC_AUTH_GSS pseudoflavors which can fail for multiple
reasons including mis-configuration.
Don't call nfs4_negotiate in nfs4_submount as it was just called by
nfs4_proc_lookup_mountpoint (nfs4_proc_lookup_common)
Signed-off-by: Andy Adamson <andros@netapp.com>
[Trond: fix corrupt return value from nfs_find_best_sec()]
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
The non-split wiphy state shouldn't be increased in size
so move the new set_qos_map command into the split if
statement.
Cc: stable@vger.kernel.org (3.14+)
Fixes: fa9ffc7456 ("cfg80211: Add support for QoS mapping")
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
