- Setting the TFS pin selector for SPORT 0 based on whether the selected
port id F or G. If the port is F then no conflict should exist for the
TFS. When Port G is selected and EMAC then there is a conflict between
the PHY interrupt line and TFS. Current settings prevent the conflict
by ignoring the TFS pin when Port G is selected. This allows both
ssm2602 using Port G and EMAC concurrently.
- some code cleanup
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Codec doesn't support to configure bit clock and frame sync polarities
- Codec doesn't support DSP_A format but DSP_B with inverted bit clock
polarity
- Match also other formats with their signal polarities
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix "ASoC: OMAP: Fix DSP DAI format in McBSP DAI driver" was not correct
due misunderstanding of DSP_A format and similar error in TLV320AIC33
codec which was used to test the original fix.
This patch corrects now DSP_A format in OMAP McBSP DAI driver and is
verified with TLV320AIC23 codec that's implementing DSP_A correctly.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix word clock length which must equal to one bit clock cycle in DSP mode.
Surprisingly McBSP is able synchronize into wrong length when it's
slave but e.g. TLV320AIC33 codec in slave configuration is outputting
some amount of noise if word clock length is longer than one bit clock
cycle.
Fix also bit clock and frame sync polarities in DSP mode since they are
opposite from I2S.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
debugfs_create_dir() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make the visibility of the tristate conditional on having the OpenFirmware
helper code enabed so that users who can't use it don't see the visible
option. Kconfig ignores dependencies for select so other users are
unaffected.
Thanks to Takashi for the suggestion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes this warning:
sound/soc/codecs/tlv320aic23.c: In function 'tlv320aic23_write':
sound/soc/codecs/tlv320aic23.c:104: warning: passing argument 2 of
'codec->hw_write' makes pointer from integer without a cast
Replaces i2c smbus write function with standard i2c write function
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The files below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
sound/soc/codecs/ad1980.c
sound/soc/codecs/wm8580.c
sound/soc/codecs/wm8900.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update the contact information for Liam Girdwood in ASoC core and
drivers as my old email address is no longer valid.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds destination and source port for dma in platform driver as
required by OMAP1
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Acked-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Device registration should be handled at the machine level and not
in the driver code itself. This patch removes the device registration
from the driver code in preparation for moving it to the machine
definition.
[Squashed down two parts to this patch for bisectability - there's also
a third part adding registration of the device to the out of tree GTA01
machine driver -- broonie]
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a couple of thinkos introduced during the I2C API update.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This prevents error messages at startup where the endpoints are being
set before the widgets/controls have even been added.
Signed-off-by: Jonas Bonn <jonas.bonn@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This suits better when adding support for multiple links and different
link formats.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Thanks to Arun KS <arunks@mistralsolutions.com> for fixing one typo in
original version of this patch.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The TLV320AIC26 Kconfig option is unusual in that it supports the
OpenFirmware machine driver which doesn't have a hard binding to the
codec driver but discovers the codec via the device tree. This makes it
meaningful to select the codec without a machine driver.
Ideally there would be a proxy entry so that this option was only
visible on OpenFirmware systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8510 microphone input PGA was represented as a DAPM PGA but in
DAPM terms the functionality is that of a mixer since it takes three
switchable inputs and produces one output. Representing it as an input
was causing its controls to be misinterpreted as gain controls and
would cause some required DAPM updates to be missed.
Reported-by: Jukka Hynninen <ext-jukka.hynninen@vaisala.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The WM8510 bias level configuration blindly overwrites the power
management registers, interfering with the operation of DAPM.
Only adjust the specific bits required, implementing use of the VMID
resistor string configuration control as we go.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement SPI support for WM8510, cut'n'pasting from the support for
WM8731 contributed by Cliff Cai and Alan Horstmann since the wire format
is the same for both codecs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Implement SPI support for WM8753, cut'n'pasting from the support for
WM8731 contributed by Cliff Cai and Alan Horstmann since the wire format
is the same for both codecs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replaces SOC_ENUM with custom SOC_SINGLE_TLV for Sidetone volume
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enables DSP DAI format for McBSP in OMAP platform driver
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With MMAP enabled (DMA mode) on the AD1981, there is +/- 250ms of delay between
writing data to alsa and audio starts coming out of the AD1981.
Copy more data to local buffer before starting DMA
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASoC machine drivers for this board were only provided as examples
for the new AT91 ASoC platform driver. Since the ETI-B1 board is
proprietary and there are other AT91 ASoC machine drivers available,
it makes sense to remove these drivers.
Signed-off-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new API call snd_soc_dapm_nc_pin() which allows machine drivers to
mark pins as being permanently disabled. At present this is identical
to snd_soc_dapm_disable_pin() except in terms of improving the internal
documentation of machine drivers that use it. The intention is that in
future it will be extended to provide additional features such as hiding
controls that are only relevant to paths using the disconnected pin.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for powering down VREF on standard headphone insertion, also
powers up the VREF on a headset insertion.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Set the third microphone to a default config of a 'Line In' to be
added the Input Source Mux's.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Since there are now multiple OpenMoko platforms it is more important to
check that the machine driver is running on the correct system. This
was orgininally generated as part of the initial GTA02 machine port.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Ingo reported Oops at probing mtpav driver. It's a race between
the irq handler and the rawmidi instance registration.
This patch fixes the order of registration to avoid the race.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The MIDI interfaces have to be detected dynamically for Edirol devices
ua-700, ua-25 and ua4-fx. This patch reverses the wrong changes made by
my other patch in uaxx-quirk.
Signed-off-by: Pedro Lopez-Cabanillas <pedro.lopez.cabanillas@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a note on the dependency of old RTC stuff, which is exclusive
with the new RTC class drivers.
http://bugme.linux-foundation.org/show_bug.cgi?id=11430
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Function dapm_mux_update_power needs enum index mux and register mask value val
as parameters, but it only has a parameter val, and uses it as both val and mux.
snd_soc_test_bits(widget->codec, e->reg, mask, val) val is register mask here,
e->texts[val] but val should be enum index mux here.
This patch adds a new param mux to fix it.
Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Increase the card components[] (and thus snd_card_info.components[],
too) array size from 80 to 128 chars so that more strings can be
stored. The 80 chars aren't enough for more than 2 HD-audio codecs,
and this hits an ugly snd_BUG() as reported by Wu Fegguang for HP
2230s.
The control protocol number is increased to 2.0.6 as well, in case
it matters.
Reported-by: Wu Fengguang <wfg@linux.intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Mic PGA Switch should be inverted in the WM8510 driver but isn't.
Reported-by: ext-jukka.hynninen@vaisala.com
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
fix a typo in comment for is_in_nid_list().
Signed-off-by: Wu Fengguang <wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
fix a typo in comment for process_unsol_events().
Signed-off-by: Wu Fengguang<wfg@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
