The v2 of NetGear WNA1000M uses a different idProduct: USB ID 0846:9043
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Cc: Stable <stable@vger.kernel.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I remove duplicated routines which related rtl92cu_set_hw_reg().
1. rtl92c_set_qos() and HW_VAR_AC_PARAM routine are similar code.
so i replace code with rtlpriv->cfg->ops->set_hw_reg().
2. rtl92c_set_mac_addr() and 'HW_VAR_ETHER_ADDR' case at
rtl92cu_set_hw_reg() routine are similar code.
so i removed rtl92c_set_mac_addr() function.
also it was not used anywhere.
3. remove HW_VAR_ACM_CTRL routine in rtl92cu_set_hw_reg().
if rtl_usb->acm_method is not EACMWAY2_SW, HW_VAR_ACM_CTRL is called
from HW_VAR_AC_PARAM. but it never called. because acm_method is always
EACMWAY2_SW. so i remove acm_method check routine
and HW_VAR_ACM_CTRL routine.
both usb and pci interface is not used HW_VAR_ACM_CTRL.
but i can't test pci interface module, so i didn't modify pci code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl92c_set_xxx_filter is same routine with rtl92cu_set_hw_reg.
so i remove those functions that are rtl92c_set_xxx_filter.
(rtl92c_get_xxx_filter is also same reason.)
also i add code updating struct rtl_mac member variable in the
rtl92cu_set_hw_reg.
after that, no more _update_mac_setting is not useful. thus i remove that.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the rtlwifi/rtl8192cu, rtl8723 code is dead code.
So I remove it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl92cu_rx_query_desc set a isampdu twice.
but second code is related to isfirst_ampdu.
so i change it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the rtlwifi/rtl8192cu, I change debug message "RTL8192CE" to
"RTL8192CU".
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
in the _rtl92c_phy_rf6052_config_parafile(), cases
RF90_PATH_A and RF90_PATH_B call the same routine.
so i remove one of these routine. also the return
routine is duplicated. so i remove it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
in the rtlwifi/rtl8192cu, INTF_PCI and INTF_USB is unnecessary.
because RTL8192CU chipset is only USB interface.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
_InitBeaconParameters() and rtl92cu_init_beacon_parameters() is
same routine. I remove both functions. then i add
_rtl92cu_init_beacon_parameters() in the hw.c.
_rtl92cu_init_beacon_parameters() is same routine with
_InitBeaconParameters().
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
in the rtlwifi/rtl8192cu, IS_HARDWARE_TYPE_8192CE and IS_HARDWARE_TYPE_8192CU
is unnecessary. because rtlwifi/rtl8192cu codes aren't shared.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After physical reconnect, the rtl8192cu chipset shows low
transmission rates.It cause is that variable "iqk_initialized"
do not de-initialized. So I add this code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
parameter "infra_mode" of rtl92c_init_beacon_max_error() is not used.
so i remove this.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialization routine set REG_BCN_MAX_ERR to 0xFF.
also _rtl92cu_set_media_status set REG_BCN_MAX_ERR to same value.
so i remove this code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add new ID for ASUS N10 WiFi dongle.
Signed-off-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB ID 2001:330d is used for a D-Link DWA-131.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I changed REG_CR+2 and (MSR) to MSR because MSR is defined as (REG_CR + 2).
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add HAL_DEF_WOWLAN case in rtl92cu_get_hw_reg
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All hw driver components in the rtlwifi driver, except for the
rtl8192de component has this bug. They would clear BE bit in the
ACM_CTRL register instead of the VO bit when processing the VO queue.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After rtl8192cu download firmware routine, set fw_ready flag.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Patch "rtlwifi: add support to send beacon frame" allows
the beaconing of rtl8192cu. But mesh beaconing is not
working. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With this change, all of the drivers now use the common routine. As this
driver has VHT capability, an additional parameter is needed, thus all the
drivers had to be modified.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The code uses macros to determine the parameters that are passed to the
rate setting routine. A simpler method is implemented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This common set of rate descriptors is renamed to be DESC_RATExx.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Four of the drivers (92ce, 92cu, 92de, and 92se) supply an argument to the
rate-mapping routine that is never used, thus it can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warning:
drivers/net/wireless/rtlwifi/rtl8192cu/hw.c:1595:6: warning:
symbol 'usb_cmd_send_packet' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl92c_set_fw_rsvdpagepkt is used by rtl8192cu and its pci sibling rtl8192ce.
rtl_cmd_send_packet crashes when called inside rtl8192cu because it works on
memory allocated only by rtl8192ce.
Fix the crash by calling a dummy function when used in rtl8192cu.
Comparision with the realtek vendor driver makes me think, something is missing in
the dummy function.
Short test as WPA2 station show good results connected to an 802.11g basestation.
Traffic stops after few MBytes as WPA2 station connected to an 802.11n basestation.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize function pointer with a function indicating bt coexist is not there.
Prevents Ooops.
Signed-off-by: Karsten Wiese <fzuuzf@googlemail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A locking problem was found in routine _rtl92ee_cmd_send_packet() that led
to system freezes. Upon inspection, several drivers had the same problem;
however, the routines all used the same code. The common code has been
moved into rtlwifi.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Realtek released new drivers on 06/28/2014. These changes implement all their
changes into the kernel version of the driver. In addition, these modifications
are part of the process of unifying the Realtek and kernel code bases.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the driver to match the latest Realtek release, and
it is an important step in getting the internal code source at Realtek to match
the code in the kernel. The primary reason for this is to make it easier for
Realtek to maintain the kernel source without requiring an intermediate like me.
In this process of merging the two source repositories, there are a lot
of changes in both, and this commit is rather large.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bt_msr & 0xfc will never match 0x3. Fix this by using a mask that actually matches the available types.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A check for CONFIG_AUTOSUSPEND was included in this driver when it was
added in v2.6.39. But that Kconfig symbol doesn't exist. Remove that
check and the single line it hides.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With certain hardware combinations the poll interval is exceeded before
initialization completes.
Tested on a MacBookPro10,1 using a Sabrent USB-A11N USB adapter.
Signed-off-by: Andy Spencer <andy753421@ucla.edu>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes: a53268be0c ('rtlwifi: rtl8192cu: Fix too long disable of IRQs')
Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit f78bccd79b entitled "rtlwifi:
rtl8192ce: Fix too long disable of IRQs", Olivier Langlois
<olivier@trillion01.com> fixed a problem caused by an extra long disabling
of interrupts. This patch makes the same fix for rtl8192cu.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The addition of a driver for the RTL8821AE requires a new API for the
fill_tx_desc() and set_desc() callback routines. This commit makes the
appropriate modifications in all the other drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A driver for the RTL8723BE will soon be added. This patch adds the
necessary parts to the common headers, and modifies the existing
drivers for those changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rtl*_set_check_bssid functions are mostly the same, but access the
RCR register in different ways. Use the get_hw_reg abstraction layer
(which reads rtlpci->receive_config for PCI devices and mac->rx_conf for
USB).
There is no functional change for cases where receive_config was
accessed directly. For rtl8192ce, there is still no change because
nothing modifies REG_RCR or receive_config. For rtl8192cu, it now also
applies changes to rx_conf from configure_filter, but that can be
considered a bug which is fixed later.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The latest vendor driver has some new values.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The latest vendor driver contains some changes not in the kernel version.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bring _rtl92c_phy_iq_calibrate() in line with the vendor driver function _PHY_IQCalibrate().
Also fix incorrect initialisation for rtl8192cu.
Signed-of-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses the newly introduced power index register routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
