This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function isn't really related to any bus core. It touches PCI
device config registers only, so move it to the (PCI) host file.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It doesn't operate on PCI core, but PCI host device, so there is no
point of passing core related struct.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bringing PCIe hosted bus up requires operating on host-related core.
Since we plan to support PCIe Gen 2 devices we should provide a helper
picking the correct one (PCIE or PCIE2).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Debug code prints the fifo name via custom dev_warn() wrappers. The
fifo_names array is only non-zero when debugging is manually enabled,
which is all well and good. However, it's *not* good that this array
uses zero-length arrays in the non-debug case, and so it doesn't
actually have any memory allocated to it. This means that as far as we
know, fifo_names[i] actually points to garbage memory.
I've seen this in my log:
[ 4601.205511] brcmsmac bcma0:1: wl0: brcms_c_d11hdrs_mac80211: �GeL txop exceeded phylen 137/256 dur 1602/1504
So let's give this array space enough to fill it with a NULL byte.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list@broadcom.com
Cc: netdev@vger.kernel.org
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcms_c_attach_malloc() function can call this with a NULL
"wlc->corestate" or "wlc->hw".
Also I threw in a bonus cleanup by deleting an obvious comment and a
no-op NULL assignment. :)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions brcmu_pkt_buf_free_skb() and release_firmware() test whether
their argument is NULL and then return immediately. Thus the test around
the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 802.11 core statistics are retrieved from the core registers
but not stored. So the debug code was never triggered to give a
warning message on tx underruns or rx overflows. This patch fixes
this and assures the statistics are stored in the snapshot.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like in case of SSB SPROMs they are encoded in a bit tricky way.
SPROM struct already uses s8 type and it's supposed to store decoded
values.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete unnecessary local variable whose value is always 0 and that hides
the fact that the result is always 0.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression ret;
expression e;
position p;
@@
-ret = 0;
... when != ret = e
return
- ret
+ 0
;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[arend@broadcom.com: make brcms_b_detach() a void function]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete a variable that is at most only assigned to a constant, but never
used otherwise.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some BCM4313 out there with a PCI id of 0x4313. These devices
are missing a sprom and are only used on routers or other embedded
devices. We found one connected to a BCM63XX SoC.
This devices was found by someone in this ticket:
https://dev.openwrt.org/ticket/13551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace the calls to bcma_core_pci_extend_L1timer() by calls to the
newly introduced bcma_core_pci_ip() and bcma_core_pci_down()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For debug purposes it is good to have the phy and radio information
available in the log. Only logged when driver is built when BRCMDBG
or BRCM_TRACING kconfig are set.
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Relegate 2 phy messages to debug status as they create excessive
log spam, noted in multiple bugzillas for brcmsmac v3.8 and up.
This is a follow on to net-next 99e9494069:
brcmsmac: Reduce log spam in heavy tx, make err print in debug
brcmsmac bcma0:0: phyerr 0x10, rate 0x14
brcmsmac bcma0:0: brcms_c_ampdu_dotxstatus_complete:
ampdu tx phy error (0x10)
Signed-off-by: John Greene <jogreene@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression introduced by:
commit 6da3b6c48d
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun Mar 24 01:45:52 2013 +0100
brcmsmac: remove brcms_bss_cfg->associated
The regression behaviour was described on mailing list.
http://mid.gmane.org/5197DC4F.7030503@broadcom.com:
"On laptop I installed kernel with brcmsmac compiled as
module. It comes up and associates during boot, but after
logging in there is no connectivity. Triggering reassoc
gives connectivity for some time, but after a while (1-2 min)
it stops."
Before the mentioned commit the return value of
the function brcms_c_ps_allowed() was always false,
which is desired behaviour as power-save is not
supported at the moment. Therefor, the function is
changed to just return false instead of simply
reverting the mentioned commit.
Bug: 58471 <https://bugzilla.kernel.org/show_bug.cgi?id=58471>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible to configure the ucode to automatically send the probe
responses to the clients after they send a probe request. At least for
WPS the userspace needs to answer the probe requests and we do not know
a way to say to the ucode to just handle the normal probe requests, so
for now no probe requests should be handled by the ucode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ucode is able to answer probe response by itself. This writes such
a template into the specific memory. Currently the probe requests are
also send to mac80211 so there are more answers send to a requesting
client. We have to make the ucode stop sending probe requests to the
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To send the correct probe response the hardware needs to know the SSID
when it changed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it possible that a beacon template provided by mac80211 is
written to the hardware for constant beaconing.
This is based on an old version of brcmsmac, on b43 and the spec b43 is
based on.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make brcms_c_set_beacon_period() write the beacon period to the
hardware if a new one is set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was a read only member, replace it with pub->up.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was a read only member. The checks using BSS are replaced by
better fitting checks of the new type member.
The change in brcms_c_tbtt() was based on code from b43, in
brcms_c_ps_allowed() the same happens with BSS being true or false,
beaconing and probe responses are just needed in ap mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it possible to easily check in which mode the device is
currently running. This also adds a function to start station mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
setting the tsf is needed to start a timer to make beaconing in AP mode
work.
This is based on older versions of brcmsmac and b43.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This exports the firmware version in use to userspace through ethtool.
root@OpenWrt:/# ethtool -i wlan0
firmware-version: 610.812
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the casts of the first argument of memset.
Neaten the style by using the sizeof the actual variable
being memset not the sizeof the type of variable.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These messages don't seem to be errors but notifications
that some attribute isn't quite right.
Don't mark them as errors.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses a long standing issue of the driver with the
mac80211 .flush() callback. Since implementing the .flush() callback
a number of issues have been fixed, but a WARN_ON_ONCE() was still
triggered because the timeout on the flush could still occur.
This patch changes the awkward design using msleep() into one using
a waitqueue. The waiting flush() context will kick the transmit dma
when it is idle and the timeout used waiting for the event is set
to 500 ms. Worst case there can be 64 frames outstanding for transmit
in the driver. At a rate of 1Mbps that would take 1.5 seconds assuming
MTU is 1500 bytes and ignoring retries. The WARN_ON_ONCE() is also
removed as this was put in to indicate the flush timeout as a reason
for the driver to stall. That was not happening since fixing endless
AMPDU retries with following upstream commit:
commit 85091fc0a7
Author: Arend van Spriel <arend@broadcom.com>
Date: Thu Feb 23 18:38:22 2012 +0100
brcm80211: smac: fix endless retry of A-MPDU transmissions
bugzilla: 42840 <https://bugzilla.kernel.org/show_bug.cgi?id=42840>
bugzilla@redhat: <https://bugzilla.redhat.com/show_bug.cgi?id=799168>
bugzilla@redhat: <https://bugzilla.redhat.com/show_bug.cgi?id=787649>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Camaleón <noelamac@gmail.com>
Cc: Milan Bouchet-Valat <nalimilan@club-internet.fr>
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue was reported on the wireless list (see [1]) in which
brcmsmac ran into a fatal error:
[ 588.284074] brcmsmac bcma0:0: frameid != txh->TxFrameID
[ 588.284098] brcmsmac bcma0:0: MI_TFS: fatal
[ 588.284103] brcmsmac bcma0:0: wl0: fatal error, reinitializing
[ 588.286208] ieee80211 phy0: Hardware restart was requested
The tx status feedback is processed in a loop limiting the number of
frames processed in one run. The code terminate processing when the
limit is reached regardless the txstatus value read from the device
register. When that status is is flagged as being valid it must be
processed as the hardware will clear it after is has been read.
Bisecting was done by Seth Forshee and showed following commit as the
culprit:
commit 57fe504817
Author: Piotr Haber <phaber@broadcom.com>
Date: Wed Nov 28 21:44:07 2012 +0100
brcmsmac: fix bounds checking in tx/rx
[1] http://www.spinics.net/lists/linux-wireless/msg101293.html
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interface address of the wireless device is determined by
the permanent address stored in the device. This patch allows
it to be overridden from user-space.
Reported-by: Maximilian Engelhardt <maxi@daemonizer.de>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/brcm80211/brcmsmac/main.c: In function ‘brcms_b_recv’:
drivers/net/wireless/brcm80211/brcmsmac/main.c:7636: warning: ‘morepending’ may be used uninitialized in this function
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This device can be found on some embedded devices connected to a
Broadcom SoC like the BCM4718.
I tested this with my Netgear WNDR3400 v1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As described in the documentation of bcma_wflush16 in drivers/net
/wireless/brcm80211/brcmsmac/types.h some PCIe controllers of Broadcom
SoCs are broken. The PCIe controller on these SoCs are mostly used to
connect some additional wifi device to the SoC and some of these wifi
devices are supported by brcmsmac.
For my BCM43224 connected to the broken PCIe controller of the BCM4718 I
need an extra read after write in brcms_b_write_objmem() to prevent a
Data bus error. This fixes the problem reading tsf_random later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for bcma wifi core revision 17 which is found on
BCM4716/4717/4718 SoCs. The firmware version 610.812 for brcmsmac found
in linux-firmware does not support these cores, but a firmware
generated with b43-fwcutter from the proprietary broadcom wireless
driver works with these chips. This wifi core contains a revision 5
N-PHY and a revision 7 radio of type 0x2056.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcms_b_txstatus and brcms_b_recv are off by one when
doing bounds checking on number of packets to process
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcms_c_isr returns true if interrupt was for us
and if dpc should be scheduled which is the same thing.
Simplify it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
