The commits,
"ath9k: Fix regression in channelwidth switch at the same channel"
"ath9k: Fix invalid noisefloor reading due to channel update"
attempted to fix noisefloor calibration when a channel switch
happens due to HT20/HT40 bandwidth change. This is causing invalid
readings resulting in messages like:
"ath: phy16: NF[0] (-45) > MAX (-95), correcting to MAX".
This results in an incorrect noise being used initially for reporting
the signal level of received packets, until NF calibration is done
and the history buffer is updated via the ANI timer, which happens
much later.
When a bandwidth change happens, it is appropriate to reset
the internal history data for the channel. Do this correctly in the
reset() routine by checking the "chanmode" variable.
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check "enable_ani" is not required since it is always
set to true and the logic for disabling/enabling ANI via
debugfs is done at a higher layer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only card with which WoW has been tested and verified is
AR9462. Do not enable it for all cards since WoW is really quirky
and needs to be tested properly with each chip.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR934x v1.3 no longer needs the DCU backoff reduction workaround for
preventing rx overruns, but in turn needs the number of usable Tx
buffers to be reduced slightly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a local bus timeout has been detected, the host interface needs to be
reset to clear the errors. AR934x uses a different synchronous interrupt
bit to indicate this, so the check needs to be fixed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow and Javier Lopez contributed these changes to
make mesh mode use the more similar AP beaconing mode and
queue parameters. Should improve PS performance, interface
concurrency (AP modes can coexist), and beacon interval
stability.
AR9271 (ath9k_htc) mesh interfaces also need to be in AP
operating mode.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According to 802.11-2007 17.3.8.6 (slot time), the slot time should
be increased by 3 us * coverage class. The code only increased the
ack timeout, which is fixed by this patch.
We have noticed in our long shot scenario that we see less collisions
with this patch.
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[add standard reference and commit message]
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparation for updating common->macaddr along with virtual interface
MAC address changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are the remaining knobs in ath9k to support DFS:
* mark AR9280 and AR9580 as DFS tested
* synchronize DFS regulatory domain to reg notifyer
* set required RX filter flags for radar detection
* process radar PHY errors at DFS detector
* notify DFS master on radar detection
DFS support requires CONFIG_ATH9K_DFS_CERTIFIED to be set.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This flag is used for indicating channel interference and
we currently do nothing with it, so remove it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On many different chips, important aspects of the MAC state are not
fully cleared by a warm reset. This can show up as tx/rx hangs, those
annoying "DMA failed to stop in 10 ms..." messages or other quirks.
On AR933x, the chip can occasionally get stuck in a way that only a
driver unload/reload or a reboot would bring it back to life.
With this patch, a full reset is issued when bringing the chip out of
FULL-SLEEP state (after idle), or if either Rx or Tx was not shut down
properly. This makes the DMA related error messages disappear completely
in my tests on AR933x, and the chip does not get stuck anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
alloc failures already get standardized OOM
messages and a dump_stack.
For the affected mallocs around these OOM messages:
Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are no longer needed for ANI functionality
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar900*_init_mode_regs needs to be called before RF banks are allocated,
otherwise the storage size of RF banks isn't known. This patch fixes
a memory overrun that can show up as a crash on unloading the module.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing this in ath9k_hw_fill_cap_info() is odd and it's
cleaner to do this in the init function for calibration.
Also, setup the supported calibration type in init_cal_settings.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a HW capability to indicate whether PAPRD is enabled
for the card, since PAPRD could be enabled in the EEPROM, but
disabled in the driver. This makes things clearer.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k: improve suspend/resume reliability" broke ath9k_htc
and bringing up the device would hang indefinitely. Fix this.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The workaround for ASPM/L0s is needed only for AR9485 1.0,
which was never sold and is not supported by ath9k.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that drv_start() always returns true, as a failing hw start usually
eventually leads to crashes when there's still a station entry present.
Call a power-on reset after a resume and after a hw reset failure to bring
the hardware back to life again.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville says:
====================
Here is another batch of updates intended for 3.7...
Highlights include an hci_connect re-write in Bluetooth, HCI/LLC
layer separation in NFC, removal of the raw pn544 NFC driver, NFC LLCP
raw sockets support, improved IBSS auth frame handling in mac80211,
full-MAC AP mode notification support in mac80211, a lot of attention
paid to brcmfmac, and the usual level of updates to iwlwifi, ath9k,
mwifiex, and rt2x00, and various other updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new callback to handle WLAN RX diversity for
AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During fast channel change, perform 2g5g_switch before starting
noisefloor calibration to avoid nfload timeout.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various parts of the code require AR9565 checks,
this patch adds them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And recognize the device in the init path.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some checks for PA linearization support checked ATH9K_HW_CAP_PAPRD and some
used the EEPROM ops, leading to issues in tx power handling, since those
two can be out of sync.
Disable the feature by default, since it has been reported that it can
cause damage to the rx path under some circumstances. It can now be enabled
for testing via debugfs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature had been disabled in ath9k because the code to support
it was incomplete, but now the code is in sync with the internal QCA
codebase, so it's time to enable it.
On many newer devices, the calibration is assumed to be done with PA
linearization enabled.
Tests with a particular AR933x device showed that the signal emitted
at full power was highly distorted and unreliable with PA linearization
disabled. With this patch, the signal becomes clear and stability
is improved.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before PAPRD training can run, the card needs to have sent a packet for
thermal calibration. Sending a dummy packet with the PAPRD training flag
set causes a crash under some circumstance.
Fix the code by replacing the dummy tx with a delay that waits for a
real packet tx to have occurred.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt is no longer handling it. While it shouldn't fire (wraparound
is highly unlikely), the consequences would be fatal (interrupt storm).
Disable the interrupt to prevent that from happening.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR1111 is same as AR9485. The h/w
difference between them is quite insignificant,
Felix suggests only very few baseband features
may not be available in AR1111. The h/w code for
AR9485 is already present, so AR1111 should
work fine with the addition of its PID/VID.
Cc: stable@vger.kernel.org [2.6.39+]
Cc: Felix Bitterli <felixb@qca.qualcomm.com>
Reported-by: Tim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Tim Bentley <Tim.Bentley@Gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
support WoW for all chipsets starting from AR9280, AR9285, AR9287,
AR9380, AR9382, AR9485, AR9462. Really all hardware may not support
WoW even though the flag is set and the WoW working depends on
your laptop, BIOS apart from the hardware.
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: vadivel@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
noisefloor calibration has to be loaded and started after
chip reset completion and restoring chainmask. Right now it is
being started before MCI reset completion on full reset. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ath9k: Fix softlockup in AR9485" with commit id
64bc1239c7 fixed the reported
issue, yet its better to avoid the possible infinite loop
in ar9003_get_pll_sqsum_dvc by having a timeout as suggested
by ath9k maintainers.
http://www.spinics.net/lists/linux-wireless/msg92126.html.
Based on my testing PLL's locking measurement is done in
~200us (2 iterations).
Cc: stable@vger.kernel.org
Cc: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add utility functions to get and test GPM offset and
remove MCI_STATE*_GPM_OFFSET states.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a full reset, mci_reset will put LNA update to the setting
for 2G mode. Those registers need to be forced to update when
the channel is in 5G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both "MAC Warm Reset" and "MCI Reset Rx" will reset GPM HW write_ptr.
We should check software cached write_ptr against HW write_ptr before
reset. Otherwise the pending DMA data will be lost.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW statemachine is sometimes found stuck in the state
WL_LNA_CTRL_DISABLE when BT is in sleep, which will cause
TX_HOLD always asserted and resmgr stuck in PENDING_TX state
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program MCI related power registers only if MCI interrupts
are enabled. This could help to reduce power consumptions when
WLAN alone is enabled in BT coex chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When software rfkill is triggered, before put the chip in reset
state, give LNA and SPDT control to BT to make sure BT can have
good RF performance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'setChip' variable is unused, remove it and
simplify the functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MCI has to be handled only when BTCOEX is actually enabled.
Check for this condition before calling MCI related functions
from various reset/calibration call-sites.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default value that is being programmed to AR_RTC_KEEP_AWAKE
is 0x2, there is no need to program it manually in various
functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ASPM has to be disabled when BTCOEX is in use, do this properly
by calling the bus-specific ASPM init routine after the
BTCOEX scheme has been determined.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR933x, the internal regulator settings need to be applied before the
PLL init to avoid stability issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes multiple issues with the current RTT
implementation in ath9k.
* The data that is obtained from the RTT interface registers
are stored in 31:5 - mask out the extra bits when reading them.
* A history buffer is maintained which is not needed at all.
Remove this array and just store the baseband data for each
chain (or bank).
* A 'num_readings' variable was being used to handle the
last entry. But it was being used in an improper manner, with
the result that the RTT values were never being written
to the RTT Interface registers. Fix this by using a simple
flag.
* Stop baseband operations before programming the calibration values
to the HW.
* Do not restore RX gain settings as part of RTT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
The delay calculation is the same for all chips, however some parts of the
code missed the extra delay factor for half/quarter.
Clean up the code and move the delay calculation to a common place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some reason the MAC timing is a bit off when waiting for ACKs, so add
some extra delay to the ACK timeout values. Significantly reduces the
number of retransmissions in my tests.
Also disable the 2.4 GHz ACK timeout workaround in half/quarter mode, it
is not required there.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to unifying regulatory limit handling
commit ca2c68cc7b
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.
This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.
This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also tweak beacon response times for better stability with the shorter
timer intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report all defined sync_cause errors in debugfs
to aid with debugging.
Use a macro to print out the interrupts file contents
to decrease code duplication.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the experiment with Azimuth ADEPT-n testbed where the APs transmit
power was reduced to 25% and the signal strength was futher attenuated
by 20dB and induced a path loss of ~7dB, the station was reporting
beacon losses and the following issue were observed.
* rx clear is stuck at low for more than 300ms
* dcu chain and complete state is stuck at one of the hang signature
This patch triggers the hang detection logic that recovers the chip
from any of the above conditions. As the issue was originally reported
in ChromeOs with AR9382 chips, this detection logic is enabled only for
AR9380/2 chips.
Cc: Paul Stewart <pstew@google.com>
Reported-by: Gary Morain <gmorain@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By checking for NR_CPUS, the compiler can optimize out register access
serialization code on non-SMP kernels
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default antenna (as programmed by the INI file) is always 0 anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Automatically set the ah->htc_reset_init on init and after PHY disable.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The logic to determine whether to use FCC is a bit convoluted.
Use a small helper function to decide whether FCC is to be
used.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tested in AR9462 Rev:2, both hardware capability flag are set
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cold reset is more reliable for getting the hardware out of some specific
stuck states.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of CONFIG_ATH9K_BTCOEX_SUPPORT in ath9k_hw
to provide a clean way of compilation without BTCOEX
support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all the MCI-specific declarations that have been
dumped unceremoniously in hw.h to ar9003_mci.h
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all the MCI-specific code in the main reset
function to helper functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting up the required scheme can be done as part of the
BTCOEX initialization path and it doesn't belong in
ath9k_hw_fill_cap_info() anyway.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
v1.0 chips are not available in the market.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Booleans should not be compared to true or false
but be directly tested or tested with !.
Done via cocci script:
@@
bool t;
@@
- t == true
+ t
@@
bool t;
@@
- t != true
+ !t
@@
bool t;
@@
- t == false
+ !t
@@
bool t;
@@
- t != false
+ t
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit adb5066 "ath9k_hw: do not apply the 2.4 ghz ack timeout
workaround to cts" reduced the hardware CTS timeout to the normal
values specified by the standard, but it turns out while it doesn't
need the same extra time that it needs for the ACK timeout, it
does need more than the value specified in the standard, but only
for 2.4 GHz.
This patch brings the CTS timeout value in sync with the initialization
values, while still allowing adjustment for bigger distances.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many systems (e.g. embedded systems) do not have wifi modules connected to
bluetooth modules, so bluetooth coexistence is irrelevant there. With the
addition of MCI support, ath9k picked up quite a bit of extra code that
can be compiled out this way.
This patch redefines ATH9K_HW_CAP_MCI and adds an inline wrapper for
querying the bluetooth coexistence scheme, allowing the compiler to
eliminate code that uses it, with only very little use of #ifdef.
On MIPS this reduces the total size for the modules by about 20k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ATH_DBG_ to macros to shorten the uses and
reduce the line count.
Coalesce ath_dbg formats.
Add missing spaces to coalesced formats.
Add missing newline terminations to ath_dbg formats.
Align ath_dbg arguments where appropriate.
Standardize ath_dbg formats without periods.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
its not used anywhere in the current code
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to enable DFS upstream we want to be sure
DFS has been tested for each chipset. Push for public
documentation of the requirements we want in place and
allow for enabling each chipset through a single upstream
commit.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable ANI for ar9100 since it seems to be working fine (and as a
matter of fact ANI was always performed for ar9100 since code which
was supposed to disable it didn't achieve this goal).
This patch sets config.enable_ani to default (true) value for
ar9100.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently in ath9k code there is an attempt which is meant to
disable ANI for ar9100 and ar9340. But it doesn't really achieve
this. All it does is disable ANI init and setup (i.e. calls to
ath9k_hw_ani_setup and ath9k_hw_ani_init). Since ath9k_hw_ani_setup is
not called ah->config.ani_poll_interval is never initialized (i.e. it
is always zero) and ath_ani_calibrate always executes ANI procedures
(over uninitialized ANI parameters).
Moreover, ath_ani_calibrate is being called each 1ms because
common->ani.timer is set to zero interval because
ah->config.ani_poll_interval==0 (and thus smallest value of all
intervals). Normally it should not be called this often.
This patch changes the code so config.enable_ani is used to check if
ANI should be performed.
config.enable_ani is initialized to true by default. This patch sets
it to false for ar9100 and ar9340.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the default tx/rx chainmask for AR9462 is 0x3.
this patch helps to assign 0x3 rather than 0x7 for
AR9462 with the help of fix_chainmask module if something
goes wrong in reading tx/rx chain mask from OTP/EEPROM
card(though its very unlikely)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
only for AR9485 (or) later chipsets TxIQ calibration
runs as part of AGC calibration. without this patch
TX IQ cal completion i.e. ar9003_hw_tx_iq_cal_run won't be executed
for AR9003
Reviewed-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
here we check for BT state and if BT calibration has started,
give 25ms for BT Calibration to finish. we also take care of 2G/5G
switch and LNA transfer incase WLAN is operating in 5G. in case the BT
state is awake when we do WLAN calibration re-calibrate and we reset
the message exchange between WLAN and BT. BT is given preference when
simultaneous CAL request happens. calibration for WLAN/BT is done
assuming that the other co-existing module is in awake state, if not
we continue to do calibration while if the other module's state changes
we need to do restart the calibration handshake
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
send halt BT GPM if the chip is in network sleep and BT state
is awake
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by
commit 2577c6e8f2 (ath9k_hw: Add
support for AR946/8x chipsets) that caused a nasty regression to
appear on my Acer Ferrari One (the box locks up entirely at random
times after the wireless has been started without any way to get
debug information out of it).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code here treats very large values of "limit" as less than
MAX_POWER_RATE because of the cast to int. We should do the compare
as u32 instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
During the fast channel change noise floor values are being loaded
twice at init_cal and after channel_change. The commit "ath9k_hw:
Improve fast channel change for AR9003 chips" overlooked it that
caused failure to load nf while doing bgscan. This patch performs noise
floor calibration after the fast and full reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Renamed to be in sync with Marketing term and to avoid
confusion with other chip names.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support the fast channel change across band switch only when there
are available of reusable cabliration results. And also observed that
doing agc control calibration on fastcc, sometimes causing calibration
timeout. Hence changing agc control to be run only on full chip reset.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supported calibrations of radio retention table (RTT) are
- DC offset
- Filter
- Peak detect
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k_hw: Improve fast channel change for AR9003 chips"
fixes the fast channel change issue for AR9003 chips that was
originally observed in AR9382 chip. Hence enabling fastcc support
again for 11A channel for AR9003 chips.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently Tx IQ calibration is enabled by default for all AR9003
chips. But for AR9480, the calibration status should be read from
chip after processing ini. And also the carrier leak calibration
status is checked during init cal. As the init_cal is being called
for fast channel change too, the tx_cl status only be read after
full reset. Hence moving that into process ini function.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to reuse Carrier leak calibration
during fast channel change for AR9480 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to reduce the overall scan time, fast channel change
should be implemented properly. This patch adds fast channel
change support across band switch or channel mode switch
instead of doing full chip reset. During the fastcc, tx iqcal
measurements are preserved and will be reloaded after successful
the channel change.
This patch also addressed fast channel issue where the STA can not
see APs in higher than operating channel on 5GHz band after
the association.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Because of not clearing Bit 14 of AR_WA, the ASPM L1 is not
enabled when entering into sleep mode. AR9480 does not need
bit 14 to be set.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is unused since the previous dead code that was using it had been
removed earlier.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code for handling various restrictions concerning regulatory limits,
antenna gain, etc. is very convoluted and duplicated across various
EEPROM parsing implementations, making it hard to review.
This patch partially cleans up the mess by unifying regulatory limit
handling in one function and simplifying handling of antenna gain.
It also removes unused transmit power scaling arrays from the EEPROM code,
which belonged to an unimplemented API that isn't supposed to be in
the driver anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the AR_SREV register does not seems to indicate whether AR9480 is
pci_express capable or not though the other information like macVersion
etc can be obtained properly. this fix is essential as ASPM won't be intialized
and its related driver functionality ath9k_hw_configpcipowersave won't be
called
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch fixes the assumption of maximum number of GPIO pins present
in AR9287/AR9300. this fix is essential as we might encounter some
functionality issues involved in accessing the status of GPIO pins which
are all incorrectly assumed to be not within the range of max_num_gpio
of AR9300/AR9287 chipsets
Cc: stable@kernel.org
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9003 seems to have issues sometimes with fast channel change
in 5GHz and this case is handled specifically for AR9280 by doing
a full reset. Let's do a full reset for 5GHz channles of AR9380
& for all channels of AR9280 pci chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for AR946/8x chipets.
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we already have ah->{rx,tx}chainmask for the same purpose
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit 9c204b46c7
(ath9k_hw: do not limit initial tx power to 20 dbm),
setting of txpower was broken.
This patch fixes it by initializing reg_pwr from the new
power limit, not the previous value.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx latecy to start signal(usec) of 11a is 41 not 37 and
also corrected the rx delay in quarter rate.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only used to workaround interoperability issues related to longer
delays in receiving the block ack, so it is not necessary to apply it
to the CTS exchange.
Should improve throughput slightly, especially when there are lots
of retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9287 v1.3+ chips, MAC runs at 117MHz. But the initvals
IFS parameters are loaded based on 44/88MHz clockrate. So
eifs/usec from ini should not be used for AR9287 v1.3+.
The mentioned values are tested on 2 chain HT40 mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize 9us slot time as that is what is used mostly
(for non-ERP cases) and also to be in sync with initvals.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9340 is not listed in ath_mac_bb_names, which leads to such a message:
ieee80211 phy0: Atheros AR???? Rev:0 mem=0xb8100000, irq=2
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here are the AR9580 1.0 initvals checksums using the
Atheros initvals-tools [1]. This is useful for when
we udate the initvals again with other values. It ensures
that we match the same initvals used internally. The
tool is documented on the wiki [2].
$ ./initvals -f ar9580-1p0
0x00000000e912711f ar9580_1p0_modes_fast_clock
0x000000004a488fc7 ar9580_1p0_radio_postamble
0x00000000f3888b02 ar9580_1p0_baseband_core
0x0000000003f783bb ar9580_1p0_mac_postamble
0x0000000094be244a ar9580_1p0_low_ob_db_tx_gain_table
0x0000000094be244a ar9580_1p0_high_power_tx_gain_table
0x0000000090be244a ar9580_1p0_lowest_ob_db_tx_gain_table
0x00000000ed9eaac6 ar9580_1p0_baseband_core_txfir_coeff_japan_2484
0x00000000c4d66d1b ar9580_1p0_mac_core
0x00000000e8e9043a ar9580_1p0_mixed_ob_db_tx_gain_table
0x000000003521a300 ar9580_1p0_wo_xlna_rx_gain_table
0x00000000301fc841 ar9580_1p0_soc_postamble
0x00000000a9a06b3a ar9580_1p0_high_ob_db_tx_gain_table
0x00000000a15ccf1b ar9580_1p0_soc_preamble
0x0000000029495000 ar9580_1p0_rx_gain_table
0x0000000037ac0ee8 ar9580_1p0_radio_core
0x00000000603a1b80 ar9580_1p0_baseband_postamble
0x000000003d8b4396 ar9580_1p0_pcie_phy_clkreq_enable_L1
0x00000000398b4396 ar9580_1p0_pcie_phy_clkreq_disable_L1
0x00000000397b4396 ar9580_1p0_pcie_phy_pll_on_clkreq
[1] git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
[2] http://wireless.kernel.org/en/users/Drivers/ath9k_hw/initvals-tool
Cc: David Quan <dquan@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EIFS value read from AR_D_GBL_IFS_EIFS register in core clocks and then
written back as microsecond value.
Signed-off-by: Alex Hacker <hacker@epn.ru>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable ASPM in pci ->probe on upstream (device) and downstream
(PCIe port) component. According to e1000e driver authors this is
required. I did not find that requirement in PCIe spec, but it seems
to be logical for me.
This need to be fixed for CONFIG_PCIEASPM, that will be done later ...
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k presents the internal calibrated noise floor as channel
noise measurement, however this results in highly chip specific values
that are only useful as relative measurements but do not resemble any
real channel noise values.
In order to give a much better approximation of the real channel noise,
add the difference between the measured noise floor and the nominal
chip specific noise floor to the default minimum channel noise value,
which is currently used to calculate the signal strength from the RSSI
value. This may not be 100% accurate, but it's much better than what's
there before.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When testing for tx power, bypass the default limits.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We receive many bug reports about system hang during suspend/resume
when ath9k driver is in use. Adrian Chadd remarked that this problem
happens on systems that have ASPM disabled.
To do not hit the bug, skip doing ->config_pci_powersave magic if PCIe
downstream port device, which ath9k device is connected to, has ASPM
disabled.
Bug was introduced by:
commit 53bc7aa08b
Author: Vivek Natarajan <vnatarajan@atheros.com>
Date: Mon Apr 5 14:48:04 2010 +0530
ath9k: Add support for newer AR9285 chipsets.
Patch should address:
https://bugzilla.kernel.org/show_bug.cgi?id=37462https://bugzilla.kernel.org/show_bug.cgi?id=37082https://bugzilla.redhat.com/show_bug.cgi?id=697157
however I did not receive confirmation about that, except from Camilo
Mesias, whose system stops hang regularly with this patch (but still
hangs from time to time, but this is probably some other bug).
Tested-by: Camilo Mesias <camilo@mesias.co.uk>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices (e.g. Ubiquiti AirRouter) ship with broken EEPROM chainmask
data, which breaks the initial calibration after a hardware reset.
To fix this, mask the eeprom chainmask with the chainmask of the chip,
and use the chip chainmask if the result is zero.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
